JavaScript appears to be disabled in your browser.
You must enable JavaScript in your browser to take advantage of all the features in this website.
Article number: 300054890 Product: M-08 Concept Carbon D Stay R 3mm Tune your M-08 Concept chassis with this 3mm-thick carbon fiber rear damper stay! Lightweight and with greater rigidity than kit standard resin parts, it boosts handling. Features 6 attachment holes (3 additional compared to kit parts) on each side for more setup options. Item Information/Contents • 3mm-thick Carbon Fiber Damper Stay (Rear) x1 • 5mm Ball Connector Nuts x2 • 5.5x1mm Spacers x2 • 3x10mm Screws x2 • Compatible with M-08 Concept chassis.
Article number: 300054889 Product: M-08 Concept Carbon DS (Fr) 3mm Tune your M-08 Concept chassis with this 3mm-thick carbon fiber front damper stay! Lightweight and with greater rigidity than kit standard resin parts, it boosts handling. Features 4 attachment holes (2 additional compared to kit parts) on each side for more setup options. Item Information/Contents • 3mm-thick Carbon Fiber Damper Stay (Front) x1 • 3x10mm Screws x2 • 5mm Ball Connector Nuts x2 • Compatible with M-08 Concept chassis.
Article number: 300054887 Product: TRF420 Toe Control RearSus Set ★The parts in this set allow toe to vary as your car's suspension works, providing greater traction in corners for even faster times! ★As the suspension moves when the car corners, the toe also changes. ★Uprights, caster blocks and lower mounts are crafted in rigid aluminum, while upright arms are carbon fiber.
Warning! Not suitable for children under 14 years.
Article number: 300054885 Product: Alum. Adjustable SepSusMt E (1/1) These parts are a new concept in Tamiya suspension mounts, using different bushings to allow adjustment of the following parameters: toe angle, tread, roll center and skid (caster) angle! There are three different types of mount, each with different dimensions. The bushings sprue contains 7 pairs of different bushing types, each type with a different hole for the suspension shafts, giving a total of 25 potential shaft offset positions. Contents/Information • Aluminum Adjustable Suspension Mount (E-a), (E-b) x1 each • Bushings Sprue x1 • This mount allows settings between C and G (toe angles depend upon separate suspension mounts and bushings used). • Mount has the iconic Tamiya blue anodized finish. • Compatible with TRF419, TA07 and TB-05 chassis cars.
Article number: 300054884 Product: Alum. Adjustable SepSusMt (A) (1/1) These parts are a new concept in Tamiya suspension mounts, using different bushings to allow adjustment of the following parameters: toe angle, tread, roll center and skid (caster) angle! There are three different types of mount, each with different dimensions. The bushings sprue contains 7 pairs of different bushing types, each type with a different hole for the suspension shafts, giving a total of 25 potential shaft offset positions. Contents/Information • Aluminum Adjustable Suspension Mount (A-a), (A-b) x1 each • Bushings Sprue x1 • This mount allows settings between XA and C (toe angles depend upon separate suspension mounts and bushings used). • Mount has the iconic Tamiya blue anodized finish. • Compatible with TRF419, TA07 and TB-05 chassis cars.
Article number: 300054883 Product: Alu Adjustable SepSusMt (XB) (1/1) These parts are a new concept in Tamiya suspension mounts, using different bushings to allow adjustment of the following parameters: toe angle, tread, roll center and skid (caster) angle! There are three different types of mount, each with different dimensions. The bushings sprue contains 7 pairs of different bushing types, each type with a different hole for the suspension shafts, giving a total of 25 potential shaft offset positions. Contents/Information • Aluminum Adjustable Suspension Mount (XB-a), (XB-b) x1 each • Bushings Sprue x1 • This mount allows settings between XD and X (toe angles depend upon separate suspension mounts and bushings used). • Mount has the iconic Tamiya blue anodized finish. • Compatible with TRF419, TA07 and TB-05 chassis cars.
Article number: 300054882 Product: Alum. Adjustable SusMt (1) E These parts are a new concept in Tamiya suspension mounts, using different bushings to allow adjustment of the following parameters: toe angle, tread, roll center and skid (caster) angle! There are three different types of mount, each with different dimensions. The bushings sprue contains 7 pairs of different bushing types, each type with a different hole for the suspension shafts, giving a total of 25 potential shaft offset positions. Contents/Information • Aluminum Adjustable Suspension Mount (E) x1 • Bushings Sprue x1 • This mount allows settings between C and G (toe angles depend upon separate suspension mounts and bushings used). • Mount has the iconic Tamiya blue anodized finish. • Compatible with TRF419, TA07 and TB-05 chassis cars.
Article number: 300054881 Product: Alum. Adjustable SusMt (A) (1) These parts are a new concept in Tamiya suspension mounts, using different bushings to allow adjustment of the following parameters: toe angle, tread, roll center and skid (caster) angle! There are three different types of mount, each with different dimensions. The bushings sprue contains 7 pairs of different bushing types, each type with a different hole for the suspension shafts, giving a total of 25 potential shaft offset positions. Contents/Information • Aluminum Adjustable Suspension Mount (A) x1 • Bushings Sprue x1 • This mount allows settings between XA and C (toe angles depend upon separate suspension mounts and bushings used). • Mount has the iconic Tamiya blue anodized finish. • Compatible with TRF419, TA07 and TB-05 chassis cars.
Article number: 300054880 Product: Alum. Adjustable SusMt (XB) (1) These parts are a new concept in Tamiya suspension mounts, using different bushings to allow adjustment of the following parameters: toe angle, tread, roll center and skid (caster) angle! There are three different types of mount, each with different dimensions. The bushings sprue contains 7 pairs of different bushing types, each type with a different hole for the suspension shafts, giving a total of 25 potential shaft offset positions. Contents/Information • Aluminum Adjustable Suspension Mount (XB) x1 • Bushings Sprue x1 • This mount allows settings between XD and X (toe angles depend upon separate suspension mounts and bushings used). • Mount has the iconic Tamiya blue anodized finish. • Compatible with TRF419, TA07 and TB-05 chassis cars.
Article number: 300054879 Product: TRF419 Alum. F Direct Cups (2) ★Lightweight aluminum direct cups give a more linear steering feel, as well as a weight savings of around 2.8g per cup compared to kit-standard parts. ★Also included are durable reinforced swing shaft caps. Compatible Chassis TRF419, TRF419X, TRF419X WS & TRF419XR Chassis
Article number: 300054878 Product: TRF SSBB Damper Upgrade Set
Give your TRF Super Short Big Bore Dampers an overhaul with this set, which includes completely redesigned set V Parts (those in Item 54871), plus dedicated new cylinder cap and 5.8mm damper ball connector nuts. Not only will they give more setup options, the new designs and material also boost durability and damper performance.
Item Contents/Information • Reinforced V Parts for TRF Dampers (damper ends, damper tops, spring retainers, etc.) x2 • Cylinder Caps x4 • 5.8mm Damper Ball Connector Nuts x8 • For use with Item 42305 TRF Super Short Big Bore Dampers (4pcs.).
Article number: 300054877 Product: T3-01 Aluminum Motor Mount
This precision aluminum motor mount can be used in place of the kit-standard resin A4 component, for more exacting attachment, and less motor strain thanks to enhanced heat sink effect.
Item Contents/Information
• Aluminum Motor Mount x1 • 3x6mm Hex Head Countersunk Screws x2 • Pinion Adapter x1 • Included pinion adapter allows use with kit-standard 26T, plus separately sold 27T and 28T 06 module pinion gears. • Compatible with T3-01 chassis models.
Article number: 300054876 Product: T3-01 Reinf. Diff Joint&Pinion
The carburized metal components in this set provide greater durability than kit-standard resin parts, giving the drivetrain more resistance to bumps and undulations, plus the ability to handle more powerful setups.
Set Contents/Information
• Metal Differential Joints x2 • Metal Differential Pinions x6 • Differential Collars x2 • Grease • Compatible with T3-01 chassis models.
Article number: 300054875 Product: TT-02 Oil Gear Diff Unit
Tamiya is delighted to announce that the gear differential unit from the recently-released TT-02RR Chassis Kit (Item 47382) is to be released as its own Hop-Up Option part!
• Glass fiber-reinforced Nylon Gear Case Parts x1 • Gasket x1 • Die-Cast Bevel Gears x4 • Oil-filled gear differential units facilitate smooth, efficient drive. Use different grades of oil, gear diff putty, etc. to quickly adjust your setup. • Compatible with TT-02 series chassis (Item 53792 required for TT-02, TT-02D; Item 53791 required for TT02B).
Article number: 300054874 Product: TT-02 Adjustable Upper Arm Set
★These upper arms allow setting of camber angle between 0 and 2 degrees via adjustment of turnbuckle shaft. ★Use Item 42236 when adjusting.
Compatible Chassis TT-02, TT-02RR & TT-02D Chassis *Use with Item 53792 Assembly Universal Shaft (TT-01, TA04).
Article number: 300054873 Product: WR-02CB T Parts Rims (2+2) DeepGry These are color variations of the rim sections from the stylish 2-part wheels used on the Comical Grasshopper (Item 58662)! Pair them with the colored spoke components (S Parts) in your model, or separately available limited edition part products, for a stylish and unique look. Item Contents/Information • WR-02CB T Parts (Deep Gray) x1 • Use with WR-02CB S Parts (Spokes) and ribbed (front) or round block (rear) bubble tires.
Article number: 300054871 Product: Rein. V Parts for TRF Dampers
Give your TRF dampers an overhaul with this completely redesigned set of V Parts, made to give you more setup options. The new designs and material also boost durability and damper performance.
• ø5mm Damper Ends (S) & (M) • ø5.8mm Damper Ends (S) & (M) • ø5mm Damper Tops • ø5.8mm Damper Tops • Spring Retainers (S) & (M) • Compatible with TRF Dampers (Items 53571, 53901, 54000 etc.) using Item 53334.
Article number: 300054870 Product: Stab. End 5mm Adjusters (4) These are brand new designs which integrate adjusters and stabilizer ends (such as those in Items 54757 and 42281). The result is a lighter chassis and improved stabilizer effect, thanks to an effective 4.7mm shortening of the stabilizer bar. Item Contents/Information - Stabilizer End 5mm Adjusters x4 - Compatible with stabilizers such as 54757 and 42281. - Adjusters may require filing down when used on some models.
Article number: 300054869 Product: OF 5mm Adjusters L (8) open Face - Open Face 5mm Reinforced Adjusters (Long) x8 - Length: 15mm - May require filing down when used on some models.
Article number.: 300054868 Product: OF 5mm Adjusters M (8) open Face - Open Face 5mm Reinforced Adjusters (Medium) x8 - Length: 11.5mm - May require filing down when used on some models.
Article number: 300054867 Product: WR-02CB Alum. Skid Guard (1) This is a lightweight and rigid one-piece aluminum front skid guard for big wheel chassis models, replacing kitstandard molded part. Its skid angle of 30 degrees helps your model barrel over rough terrain, insulating chassis components against bumps and shocks. Item Contents/Information • Skid Guard x1 • Used in place of kit-standard F4 or M8 which holds U-shaped shaft in place. • Can be used in tandem with kit-included front bumper parts. • Two 3x10mm screws for attachment are included. • Compatible with WR-02, WR-02C, WR-02G, GF-01, G6-01 and WR-02CB chassis models.
Article number: 300054866 Product: RndBlk R Bubble Tires Soft (2) These tires, which were first developed for our new Comical Grasshopper (Item 58662), are now released as Hop-Up Options for use with Tamiya big wheel chassis! Item Contents/Information • Round Block Rear Bubble Tires (Soft) x2 • Tire width/diameter: 56mm/98mm • Tires have a distinctive rounded "bubble" shape for a fun look and drive. • Round block pattern makes for excellent grip and drive. • Soft compound maximizes grip, even on poorer surfaces. • Compatible with WR-02CB, WR-02C, WR-02G, GF-01 and G6-01 chassis models. Please note standard WR-02 chassis are not compatible.
Article number: 300054864 Product: T3-01/WR-02 Multipurpose Driver Figure Here is a new, versatile driver figure ready to take the wheel (or handlebar) of your models! This figure has been included in the Dual Rider (Item 57407) kit. Item Contents/Information • This is an assembly driver figure with two potential helmet types: screw-attach the visor and chin guard parts for a motocross style helmet, or remove them for a standard type. • Hand parts rotate to allow their fitting to included steering wheel and handlebar. • Screws and small parts for attachment are included. • Stickers create 4 different designs of eye, plus one pair of sunglasses, analog instrumentation for motorbike models, and digital displays for both car and bike models, plus plenty of generic designs. • Paint as you like using Tamiya Color plastic paints. • Compatible with T3-01, WR-02 and GF-01 chassis models (not WR-02G and Heavy Dump Truck models).
Article number: 300054863 Product: Alum. HT Servo Saver Cap Ensure that your servo is well protected with this durable and lightweight aluminum cap for use with hi-torque servo savers. Item Contents/Information • Aluminum Hi-Torque Servo Saver Cap x1 • This cap is for use in place of Q4 parts in hi-torque servo savers, providing good durability. • The part has the iconic Tamiya blue anodized finish, with the TAMIYA name laser-engraved.
Article number: 300054862 Product: Alum. Servo Step Screws (4) Get the best out of your servo with these step screws, which give tighter and more secure attachment. Item Contents/Information • Aluminum Step Screws x4 • Step screws cater to holes between 4.5mm and 5mm, and do not require washers, meaning that they give a great fit and save maintenance time. • Hex holes ensure tight attachment. • Some servos may only require 2 screws.
Article number: 300054861 Product: 1:10 Rally Block Tire Soft *2 26mm Here is another tire option for your touring car model: these are soft compound rally block tires which provide super grip in cooler running conditions, in particular. Item Contents/Information • Rally Block Tires (Soft) x2 • Tire Inserts x2 - these are the same as were included in Item 53133. • This product comes in a re-openable zippered bag. • Compatible with 26mm width wheels such as Items 53232 and 53914. • Compatible with tire inserts such as Item 53156.
Article number: 300054860 Product: T3-01 370 Sport-Tuned Motor
★This tuned motor is perfect for use with the R/C Dancing Rider, and offers dynamic drive. ★Input voltage: 6.6-7.2V ★RPM: 22,200 (at 7.2V) ★Maximum torque: 4.91mN-m ★Maximum usage: 2.85A
Compatible Chassis T3-01 Chassis *Use with Item 54228 Fluorine Coated 06 Module Pinion Gear (26T, 27T), Item 54834 T3-01 Full Ball Bearing Set, Item 54857 T3-01 One-Piece Rear Axle Shaft Set and Item 54876 T3-01 Reinforced Differential Joint & Pinion Set. **Item 55105 LF1100-6.6V Racing Pack (M-Size) is required as a power source..
Article number: 300054859 Product: T3-01 FRP Support Arms
2mm thick FRP support arms part reinforces the chassis and gives the driver even greater controllability!
• FRP Support Arms x1 • Screws and other small parts for attachment are included. • Compatible with T3-01 chassis models.
Article number: 300054857 Product: T3-01 1pc Rear Axle Shaft This is a rigid, highly durable one-piece shaft for efficient drive and secure wheel attachment. Comes with blue anodized 9mm hex hub. (Not compatible with T3-01 specific wheels.)
Article number: 300054856 Product: Body Set Dancing Rider Chrome This is a chrome plated spare body set of the Dancing Rider. For the modeler’s convenience, the body comes pre-cut. • Chrome plated finish polycarbonate body. The body is pre-cut, and features holes already drilled for mounting on the T3-01 chassis. • Stickers are included to decorate the body. • Compatible with T3-01 chassis models.
Article number: 300054853 Product: 1:10 Twin5spk Wheels +2 Bla (4) 24mm - Twin-spoke design wheels are a perfect match for super sports car models. - These components are molded in black. - Offset: +2
Article number: 300054852 Product: 1:10 18-Spk Wheels 0 FlYel (4) 24mm - 18-spoke wheels are a perfect option for racing cars. - These components are molded in jazzy fluorescent yellow. - Offset: 0
Article number: 300054851 Product: 1:10 RallyDish Wheels 0 Whi (4) 24mm This spare wheel set depicts the spoke wheel commonly seen on Subaru Impreza R/C models. • Rally Dish Wheels (White) x4 • Zero offset. • Compatible with 1/10 scale touring car tires: Items 51023, 51049, 53433, 53705, 54256 and 54293.
Article number: 300054850 Product: 1:10 Mesh Wheels +2 FlYel (4) 24mm This is a color variation of Tamiya’s classic mesh wheel set for touring and sports car R/C kit models. The original set of wheels come in white, whereas these come in a vibrant shade of yellow. • Mesh Wheels (Yellow) x4 • Wheels have an offset of +2. • Compatible 1/10 scale 24mm width touring car tires: Items 51023, 51049, 53433, 53705, 54256 and 54293. • Compatible tire inserts: Items 53434, 53435, and 53582.
Article number: 300054849 Product: Aluminum Wing Washers (2) Blue These lightweight 14mm-diameter aluminum components stabilize polycarbonate racing wings used on R/C cars. Compared to the standard attachment method, these wing washers will allow the wing to be more effective. Furthermore, they provide protection in the event of crashes and rolls. • Aluminum Wing Washers x2 • 3x8mm Titanium Screws x2 • Wing washers have a blue anodized finish. • For use with aluminum adjustable wing stays (Items 54510 and 54773).
Article number: 300054848 Product: Aluminum Wing Washers (2) Black These lightweight 14mm-diameter aluminum components stabilize polycarbonate racing wings used on R/C cars. Compared to the standard attachment method, these wing washers will allow the wing to be more effective. Furthermore, they provide protection in the event of crashes and rolls. • Aluminum Wing Washers x2 • 3x8mm Titanium Screws x2 • Wing washers have a black anodized finish. • For use with aluminum adjustable wing stays (Items 54510 and 54773).
Article number: 300054847 Product: TB-05 Carb R Damper Stay SSBB
This Carbon Fiber shock tower is for use on TB-05 chassis race car kits. It allows you to install Tamiya’s world famous TRF Super Short Big Bore Dampers. The combination of the two parts will result in a car set up that exhibits a lower center of gravity.
• Carbon Front Damper Stay x1 • Crafted from 3mm thickness carbon fiber material for superb rigidity and optimal damper performance. • Features 3 extra damper attachment holes (total 6), for a wider range of setup options. • Compatible with TB-05 PRO chassis cars using TRF Super Short Big Bore Dampers.
Article number: 300054841 Product: T3-01 Front Tire soft (1) This is a soft compound tire for the front of the T3-01 chassis. (Dancing Rider kit) Using this tire will open up a number of different setup options, particularly enhancing grip in mid speed ranges. • Front Tire (Soft) x1 • Inner Sponge x1 (equivalent to Item 54590 M-Chassis Inner Sponge (Super Hard)) • Compatible with T3-01 chassis models.
Article number: 300054840 Product: T3-01 R Spring Soft/Hard This rear cam side spring option is designed for the T3-01 (Dancing Rider Kit) chassis. These springs replace the kit standard MA10 parts in the rear slide suspension. By using this option spring set, it will help you adapt the model to changing surface conditions and model speed. • Rear Spring (Soft) x1 • Rear Spring (Hard) x1 • Compatible with T3-01 chassis models.
Article number: 300054839 Product: T3-01 F Spring Soft/Hard This front fork spring set option is designed for the T3-01 (Dancing Rider Kit) chassis. These springs replace the kit standard MC9 parts in the front fork tubes. By using this option spring set, it will help you adapt the model to changing surface conditions and model speed. • Front Springs (Soft) x2 • Front Springs (Hard) x2 • Compatible with T3-01 chassis models.
Article number: 300054838 Product: T3-01 Feder-Set Lenkung Mittel/Hart This steering spring set is designed to be used with the T3-01 (Dancing Rider Kit) chassis. These springs replace the kit standard MC10 parts in the top of the front fork. By using these stiffer options, it will help adapt your machine to different surface conditions and model speed. • Steering Spring (Medium) x1 • Steering Spring (Hard) x1 • Sponge Tape (15x150mm) x1 • Compatible with T3-01 chassis models.
Article number: 300054835 Product: T3-01 Alu Adjst Link Arm Set This turnbuckle link arm replaces the A9 part in the T3-01 chassis kit. This option part is lightweight, durable and allows adjustability with the link arm between the servo and gearbox, which will let you adjust the lean angle and turn achieved by the model, as well as allowing easier use of a variety of servos. • 3x42mm Aluminum Turnbuckles x2 • 5mm Adjusters (Gray) x4 • 5mm Ball Connectors (Black) x4 • Screws and other small parts for attachment included. • Compatible with T3-01 chassis models.
Article number: 300054834 Product: T3-01 Full Ball Bearing Set This is a ball bearing set for the T3-01 Dancing Rider Trike. Ball bearings vastly improve efficiency in all moving parts, thereby increasing speed and run time. • 1280 Ball Bearings x2 • 1060 Ball Bearings x8 • 630 Ball Bearings x4 • Install in place of kit standard G1 (diff), G2 (front wheel, rear axles) and G3 (gear) plastic bushings. • Compatible with T3-01
Article number: 300054832 Product: T3-01 W Pin Spike Tires R *2 These are wide pin spike tires designed to be used with the Tamiya T3-01 Dancing Rider Trike kit. They offer more stability than the standard tires in the original kit. The pin spikes will also allow you to more easily transverse through low cut grass, turf and hard pack dirt surfaces. • Rear Wide Pin Spike Tires x2 • Inner Sponges x2 • Compatible with T3-01 chassis models employing dedicated wheels in Item 54833
Article number: 300054831 Product: T3-01 Chrome Whl 4 WSS Tire R (2) These are plastic chrome plated rear wheels designed for the T3-01 Dancing Rider Trike kit. They offer a wider stance thereby improving stability when used in conjunction with a wider tire. • Wheels for Rear Wide Semi-Slick Tires x2 • Attach using B7 and 2.6x20mm screws included in the chassis kit. • Compatible with T3-01 chassis models employing dedicated tires in Item 54830.
Article number: 300054830 Product: T3-01 W Semi-Slick Tires R (2) These are wide semi-slick tires designed to be used with the Tamiya T3-01 Dancing Rider Trike kit. They offer more stability than the standard tires in the original kit. • Rear Wide Semi-Slick Tires x2 • Inner Sponges x2 • Compatible with T3-01 chassis models employing dedicated wheels in Item 54831.
Article number: 300054828 Product: 1:14 H Parts Racing Truck (Chrome) ★Shiny chrome plated H parts sprue with side mirror, coupler and rear bumper components, to customize your racing truck model. ★Please note that mirror surface parts are not included in this product.
Article number: 300054825 Product: TB-05 Carbon Rein. Lower Deck This is a carbon fiber-reinforced nylon resin version of the TB-05 PRO lower deck, which features integrated side frame sections. Compared to the standard FRP (Fiberglass Reinforced Plastic) chassis, from the stock kit, carbon reinforced plastic offers increased rigidity. This option part is especially helpful to use when driving under high-grip track conditions. • TB-05 PRO Lower Deck x1 • Carbon-fiber reinforced deck improves performance on high-grip carpet and asphalt surfaces.
Article number: 300054824 Product: M-Chassis 11spk Whl Plt (2) These are chrome plated rear wheels to the T3-01 trike chassis. Use it to spice up the look of your Dancing Rider Kit. • Chrome Plated 11-Spoke Wheels x1 • Compatible with T3-01 and M-chassis models.
Article number: 300054819 Product: XL UrtnBumper Bla TT-02/TT-01E This extra-large (XL) bumper is made from black urethane, as opposed to the gray bumpers used on many of Tamiya’s on-road RC kits. Cut it to just the size you need for a perfect fit to your model’s body! • Urethane Bumper (Black) x1 • Bumper helps absorb shocks and lessen the chance of body damage. • Compatible with TT-02 and TT-01 Type-E chassis cars.
Article number: 300054817 Product: Alu. Motor Guard GF-01/WR-02 This handy motor guard is compatible with Tamiya’s GF-01. G6-01 and WR-02 chassis. Employ it to protect your model’s motor from dust and debris and help it dissipate heat too. • Aluminum Motor Guard x1 • Two included 3x28mm cap screws make for extremely secure attachment to the motor. • A hex wrench is included to aid in attachment. • Compatible with GF-01, G6-01 and WR-02 chassis cars.
Article number: 300054816 Product: DT-03 Rein M Part DS Mount These are carbon fiber-reinforced plastic M parts. The sprue contains damper stay mount, wing stay, front bumper parts and more. • DT-03 Reinforced M Parts Sprue x1 • Carbon-fiber reinforced parts improve chassis rigidity, and performance on high-grip carpet and asphalt surfaces. • Compatible with DT-03 chassis cars.
Article number: 300054815 Product: TT-02B Rein Covers & L-Arms (2) These are carbon fiber-reinforced plastic parts. The sprue contains lower suspension arm, gear cover parts and more. • TT-02B Reinforced Gear Cover & Lower Suspension Arm Parts x2 • Contains the following parts from the TT-02B C sprue: C1 (front lower arms), C9 (rear lower arms), C6 (body mounts), C7 (gear covers) and C8 (battery posts) • Glass fiber-reinforced parts improve chassis rigidity, and performance on high-grip carpet and asphalt surfaces. • Compatible with TT-02B chassis cars. Use with turnbuckle shafts.
Article number: 300054814 Product: TT-02 Carbon Bumper Support This is a carbon fiber bumper support for the TT-02 touring car chassis. Using this piece will reduce chassis weight and boost its durability at the same. • 2mm thick Carbon Fiber Bumper Support x1 • Install in place of TT-02 B7 or TT-01 Type-E D4 parts for more secure attachment. • Compatible with TT-02 and TT-01 Type-E chassis cars (cannot be used on TT-02B).
Article number: 300054813 Product: M-07 Concept LF Kingpin Pipe (4) These components are used in place of the kit-standard MB16 parts and are fitted into the front uprights. When used they give super smooth suspension motion. • Low-Friction Kingpin Pipes x4 • Low-friction plated surface gives smooth motion. • Compatible with M-07 Concept cars.
Article number: 300054812 Product: M-07 Concept Hi-Trac LowerDeck This is a carbon fiber-reinforced plastic main chassis for the distinctive M-07. Compared to the standard fiberglass reinforced chassis, it will flex significantly less under load. This set up is ideal when racing your car on high-grip surfaces. • M-07 Concept Lower Deck x1 • Carbon-fiber reinforced part optimizes chassis flex for improved performance on high-grip surfaces, without compromising pitch rigidity. • Compatible with M-07 Concept chassis.
Article number: 300054811 Product: M-07 Concept Rein. D Pts (2) These are carbon fiber-reinforced nylon plastic D parts (suspension arms) for the M-07 chassis. They exhibit stiffer flex characteristics compared to the standard plastic parts found in the standard kit. These suspension arms are ideal to use under high grip surfaces. • M-07 Concept D Parts Sprues x2 • Carbon-fiber reinforced parts improve chassis rigidity, and performance on high-grip carpet and asphalt surfaces. • Compatible with M-07 Concept chassis.
Article number: 300054810 Product: M-07 Concept Rein. C Pts (2) These are carbon fiber-reinforced nylon plastic C parts for the M-07 chassis. They exhibit stiffer flex characteristics compared to the standard plastic parts found in the standard kit. • M-07 Concept C Parts Sprues x2 • Carbon-fiber reinforced parts improve chassis rigidity, and performance on high-grip carpet and asphalt surfaces. • Compatible with M-07 Concept chassis.
Article number: 300054807 Product: G6-01 D Parts Chassis ClrGry The G6-01 chassis has a fascinating drivetrain, and it almost seems a shame to cover it up with the sturdy monocoque chassis. Well, now you can keep it safely covered yet still see the inner workings with these clear gray monocoque parts! • G6-01 D Parts Sprue (Clear Gray) x1 • Parts are molded in clear gray polycarbonate. • Used in place of kit standard black components, these parts allow viewing of the drivetrain as the model runs! • Compatible with G6-01 chassis cars.
Article number: 300054805 Product: TB-05 Carbon Side Members (2) 2,5mm These carbon fiber parts for the TB-05 PRO chassis are designed to endow it with much greater rigidity, allowing you to adapt to a wider range of track conditions. • 2.5mm-thick Carbon Fiber Side Members x2 • Greater rigidity leads to more stable handling. • The parts are attached to the side frames only, ensuring that they do not hinder access to and maintenance of key areas such as the differentials, steering setup and R/C equipment. • Compatible with TB-05 PRO chassis
Article number: 300054804 Product: TB-05 Carbon Damper Stay R 3mm Tune your TB-05 PRO chassis with this 3mm thick carbon fiber rear shock tower! Lightweight and with greater rigidity than kit standard plastic parts, it boosts handling. Features 7 attachment holes (3 additional than the standard shock tower) on each side for more setup options. • 3mm-thick Carbon Fiber Damper Stay (Rear) x1 • Screws for attachment included. • Compatible with TB-05 PRO chassis. • Recommended for use with Items 42102, 42287 and 50746.
Article number: 300054803 Product: TB-05 Carbon Damper Stay F 3mm Tune your TB-05 PRO chassis with this 3mm thick carbon fiber front shock tower! Lightweight and with greater rigidity than kit standard plastic parts, it boosts handling. Features 5 attachment holes (2 additional from the kit standard shock tower) on each side for more setup options. • 3mm-thick Carbon Fiber Damper Stay (Front) x1 • Screws for attachment included. • Compatible with TB-05 PRO chassis. • Recommended for use with Items 42102, 42287 and 50746.
Article number: 300054801 Product: TB-05 Aluminum Steering Arms (2) These are aluminum steering arms for the TB-05 race car chassis. By using these instead of the standard plastic arms, they sharpen steering response leading to more precise motion and direct steering feel. • Aluminum Steering Arm (Right) x1 • Aluminum Steering Arm (Left) x1 • Anodized blue finish. • Recommended for use with separately sold aluminum servo mount (Item 54800) and steering bridge (Item 54802). • Compatible with TB-05 PRO chassis.
Article number: 300054799 Product: TT-02 HT ServoSaver & Alu.Horn
This set includes a hi-torque servo saver and dedicated TT-02 design aluminum servo horn to protect internal servo gears and give more direct steering feel to your car.
• Hi-Torque Servo Saver (Black) x1 (Item 51000) • TT-02 Aluminum Servo Horn x1 • Screws for attachment included. • Compatible with all TT-02 chassis variants.
Article number: 300054798 Product: TA-07 Low-Friction Belt 750/White ★This belt is made from low-friction material and is 0.2mm thinner than the standard part, for very smooth running and superb efficiency. ★White material makes for easy identification.
Article number: 300054797 Product: Touring Car Short Springs II
Different spring stiffnesses make a big difference to handling in any of Tamiya’s 1/10 touring cars. This short set compliments the existing line-up of springs with three new spring rates. Use them to get your car set up just right for the conditions of the track and your driving style. The springs come in black and have a unique color mark for easy differentiation.
• Super Hard Short Springs (White) x2 • Medium-Hard Short Springs (Gold) x2 • Medium-Soft Short Springs (no color mark) x2 • These 3 types complement Hard, Medium and Soft springs in Item 42168. • Compatible with touring car short dampers (Items 50519, 50746, 53155, 53280, 53571, 53901, 54000, 54753, 42102, 42273, 42287, 42291 and 47342).
Article number: 300054794 Product: 2-Piece Mesh Wheels (2) Black This is a two-piece mesh wheel set. The wheel rim itself is chrome plated while the mesh centerpiece is molded in black. The set is a color variation of the classic wheels from Item 50548, which include a gold color center piece. Item Contents •Hubcap Sections (Black) x2 •Rim Sections (Plated) x2 •Assembly required. 2 types of offset can be achieved, depending upon the assembly method used. •Compatible with 1/10 scale R/C touring car models using narrow 26mm tires.
Article number: 300054792 Product: Body Set R/C PC Reinf Mesh Tape (2m) This polycarbonate reinforcing mesh tape is the perfect solution for hobbyists that are a little more than rough with their bodies. With this tape you can easily reinforce spoilers, fenders and the like with this handy mesh type tape, simply apply clear silicone adhesive to secure the mesh tape in place. Item Contents •2-meter roll of mesh tape (35mm width) x1 •Apply to the inside of the body, on the area you wish to reinforce •Fix into place with separately sold clear silicone adhesive found at local hardware stores
Article number: 300054791 Product: M-07 Concept Carbon BmpSpt This lightweight and rigid carbon fiber support replaces the stock plastic part on the M-07 M-Chassis kit. It will help keep the urethane bumper securely in place. Set Contents •Carbon Fiber Bumper Support x1 •Small parts for attachment included. •Compatible with M-07 Concept chassis cars.
Article number: 300054789 Product: TA-07 Carbon Stiffeners (Rear) Increase your setup options for the TA07 PRO chassis with these 3mm thick carbon fiber versions of the rear plastic stiffeners! Lightweight and rigid L/R stiffener parts fuse chassis and bulkheads together for great rigidity, altering handling characteristics. These parts are ideal for track conditions that have high grip. When using these parts, the chassis will exhibit less lateral chassis flex compared to using resin standard parts.
Article number: 300054788 Product: TA-07 Carbon Stiffeners (Front) Increase your setup options for the TA07 PRO chassis with these 3mm thick carbon fiber versions of the front plastic stiffeners! Lightweight and rigid L/R stiffener and steering support parts fuse chassis and bulkheads together for great rigidity, altering handling characteristics. These parts are ideal for track conditions that have high grip. When using these parts, the chassis will exhibit less lateral chassis flex compared to using resin standard parts.
Article number: 300054787 Product: M-07C Alu Querlenkerhalter hi./+0,5 blau These durable, precision suspension shaft mounts have suspension ball holes offset by 0.5mm (2 different positions) compared to the standard mounts in Item 54760 M-07 Concept Rr Sus. Mount Aluminum. By switching their attachment positions, you can alter rear suspension arm skid angle! They give secure arm attachment, and keep motion smooth, even with toe applied. •Aluminum Rear Suspension Mounts x4 (2 types x2 each) •Blue anodized finish. •Small parts for attachment are included. •Compatible with M-07 Concept chassis cars.
Article number: 300054786 Product: M-07C Alu Querlenkerhalter vo./4° blau This suspension mount is crafted in aluminum for excellent rigidity compared to the standard plastic part found in the M-07 M-Chassis kit. It also gives a caster angle of 4° compared to the 5° offered by kit B1 parts. The 4-degree angle provides more bite in the turns, which is ideal for short and technical course tracks. •Aluminum Front Suspension Mount (4°) x1 •Blue anodized finish. •Compatible with M-07 Concept chassis cars only.
Article number: 300054785 Product: R/C Body Mt Hole Clear Patches (8) 0,5mm These clear patches can be used to protect your R/C model body mount holes from unsightly cracks and widening. Item Contents •Clear Patches x8 •0.5mm thickness clear material provides effective and discreet reinforcement •Internal diameter of 6.5mm allows use on most body mount holes
Article number: 300054783 Product: TC-01/TA-07 Carbon Crossmember Rear ★This 2mm thickness carbon fiber part connects left and right rear body mounts, for more rigidity and less body wobble. ★It offers a choice of 3 body mount positions.
Article number: 300054782 Product: C-01/TA-07 Carbon Crossmember Front ★This 2mm thickness carbon fiber part connects left and right front body mounts, for more rigidity and less body wobble. ★It also has transponder attachment holes.
Article number: 300054781 Product: M-07 Concept Alu R Uprights (2) blau These tough and lightweight aluminum rear uprights not only bolster the M-07 Concept chassis suspension, they also have a 2-piece design that allows adjustment of upper arm length and angle, which allows you to adjust the handling of your car to suit course and track conditions. •2-Piece Rear Uprights x2 •Blue anodized finish. •2mm spacers, ball connectors and screws for attachment included. •Compatible with M-07 Concept chassis cars only.
Article number: 300054774 Product: Raikiri GT Body Whi Painted ★This handy set includes the stylish Kota Nezu-designed Raikiri GT R/C car body and wing molded in 1mm polycarbonate and pre-painted in white. ★Cut out the body and wing, make holes, apply stickers and attach the wing yourself. Compatible Chassis 257mm wheelbase touring car chassis that fit bodies 188mm or less in width.
Article number: 300054773 Product: Alu. Adjustable Wing Stay 2 This versatile Wing Stay Set facilitates a number of wing angle options. It allows attachment at 8° increments between 8° and 32°. Furthermore, it positions the wing itself 10mm or 20mm (this depends upon attachment holes used) further rearwards than the previous aluminum wing mount. (item 54510) • Wing stay mounts x2 • Wing stay adjustable parts x2 • Compatible with touring car bodies with space to make attachment holes. Note: Wing parts are sold separately. Compatible with the following wing sets: 54729 RC Racing Wing Carbon Pattern, 54688 RC Racing Wing Set 2 Carbon Pattern, 54494 RC Racing Wing Set 2, 54458 RC Racing Wing B, 54457 RC Racing Wing A, 53604 RC Racing Wing Set, 53470 RC Lightweight Wing Carbon.
.
Article number: 300054771 Product: Pinion Gear Coated Alu 24T M0.6 This aluminum pinion gear is lightweight and features a durable hard coating. Thanks to its rounded teeth, it has greater resistance to wear and lower drivetrain friction loss. The gear is compatible with 06 Module spur gears.
Article number: 300054770 Product: Pinion Gear Coated Alu 22T M0.6 This aluminum pinion gear is lightweight and features a durable hard coating. Thanks to its rounded teeth, it has greater resistance to wear and lower drivetrain friction loss. The gear is compatible with 06 Module spur gears.
Article number: 300054769 Product: Pinion Gear Coated Alu 18T M0.6 This aluminum pinion gear is lightweight and features a durable hard coating. Thanks to its rounded teeth, it has greater resistance to wear and lower drivetrain friction loss. The gear is compatible with 06 Module spur gears.
Article number: 300054768 Product: 06 H. Coated Alu. Pinion 17T This aluminum pinion gear is lightweight and features a durable hard coating. Thanks to its rounded teeth, it has greater resistance to wear and lower drivetrain friction loss. The gear is compatible with 06 Module spur gears.
Article number: 300054763 Product: M-07C Alu Lenkhebel-Set (L/R) Blau elox. This aluminum steering arm set helps sharpen up the M-07 Concept’s steering response. The more precise motion also leads to a direct steering feel compared to the standard FRP plastic parts. Furthermore, aluminum parts offer extremely secure attachment. •Aluminum Steering Arm (Right) x1 •Aluminum Steering Arm (Left) x1 •Anodized in blue finish. •Compatible with M-07 Concept chassis. •Note: Ball bearings are sold separately.
Article number: 300054762 Product: M-07 Concept Carbon D Stay Rear Tune your M-07 Concept chassis with this 3mm thick carbon fiber rear damper stay! Lighter weight and with greater rigidity than kit standard plastic parts, it boosts handling and offers more tuning options. The damper stay also features 4 attachment holes compared to the 2 attachment holes from the kit standard shock tower. •3mm-thick Carbon Fiber Damper Stay (Front) x1 •Screws for attachment included. •Compatible with M-07 Concept chassis.
Article number: 300054761 Product: M-07 Concept Carbon D Stay F Tune your M-07 Concept chassis with this 3mm thick carbon fiber front damper stay! Lighter weight and with greater rigidity than kit standard plastic parts, it boosts handling and offers more tuning options. The damper stay also features 4 attachment holes compared to the 2 attachment holes from the kit standard shock tower. •3mm-thick Carbon Fiber Damper Stay (Front) x1 •Screws for attachment included. •Compatible with M-07 Concept chassis.
Article number: 300054760 Product: M-07 Concept Alu. R Sus Mt (4) These durable, precision aluminum mounts make for secure suspension arm attachment on the M-07 Concept chassis. Suspension balls are included to keep motion smooth, even with toe applied to the wheels. •Aluminum Rear Suspension Mounts x4 •Anodized in blue. •Small parts for attachment included. •Compatible with M-07 Concept chassis.
Article number: 300054759 Product: M-07 Concept Alu. Heat Sink This aluminum heat sink uses fins to help heat dissipate from the motor mounted on the M-07 Concept chassis. The use of a heat sink helps to prevent loss of performance from overheating in a long race. •Aluminum Motor Heat Sink x1 •Anodized in blue. •3x8mm screw for attachment included. •Compatible with M-07 Concept chassis.
Article number: 300054757 Product: M-07 Concept Stabilizer Set FR (2+2) These stabilizers are designed to be used with the M-07 Concept machine. They are a valuable tool in adjusting the M-07 Concept setup by quickly and easily altering the suspension rigidity and handling characteristics. The set includes 2 stiffness’s for the front and rear of the car, plus adjusters to easily alter the Left and right balance. •Front Stabilizers (Soft: red, Hard: blue) x2 •Rear Stabilizers (Soft: red, Hard: blue) x2 •Adjuster rods, stabilizer stoppers and small parts for attachment included. •Compatible with M-07 Concept chassis.
Article number: 300054755 Product: TA-07 Carbon Stiffener (Center) Increase your setup options for the TA07 PRO chassis with this 2mm thick carbon fiber center stiffener. This lightweight and rigid part fits neatly onto the center brace and rear stiffeners for more rigidity and stiffer pitch damping. Item Contents •Carbon Fiber Stiffener (Center) x1 •Screws for attachment included. •This item pairs perfectly with carbon fiber front (Item 54788) and rear (Item 54789) stiffeners. •Compatible with TA07 PRO chassis cars.