RC spare parts
Discover first-class RC spare parts from Tamiya. Screws, shock absorbers, drives and much more! If you want to find out more, you can read on here.
Other spare parts & accessories
10mm Shim Set, RC accessory, 0.1-0.3 mm spacers
300053588€13.49
This 10 mm shim set brings fine mechanical adjustment to RC chassis work, with 30 spacers sized at 10 mm inner diameter and 13 mm outer diameter for controlled spacing at shaft mounting points. The 3 thickness options of 0.1 mm, 0.2 mm and 0.3 mm make it possible to correct small gaps that can lead to unwanted movement in suspension or wheel axle assemblies. Instead of relying on a single washer size, the set gives stepped tuning options that suit different setup needs across on-road and off-road vehicles. Each shim can be placed to shift the position of a mounted part in small increments, including forward adjustment where the chassis layout calls for tighter spacing. That makes the set useful during maintenance, rebuilds and race-focused setup changes where alignment and reduced slippage matter. Scope of delivery: 1 spacer set with 30 pieces. On the bench, the assortment supports careful fitting of moving parts before a run. During a rebuild or handling-focused setup session, the different shim thicknesses help dial in cleaner spacing at the exact point where play needs to be reduced. Warning! Not suitable for children under 14 years.
Axes & drive shafts
12 mm Wheel Hub Hexagon Set, RC chassis accessory
300053056€10.59
This 12 mm wheel hub hexagon set brings a clean aluminium upgrade to the wheel mounting area on a wide range of RC chassis. The pin-type design pairs each hex hub with a matching pin, creating the interface that transfers drive from the axle to the wheel while keeping the fit consistent during assembly, maintenance and parts replacement. The scope of delivery includes 4 wheel hub hexagons and 4 pins. The aluminium construction gives these small drivetrain parts a crisp machined look, and the 12 mm hex format matches the standard wheel mounting size used across many compatible on-road and off-road platforms. Fitment listed in the data covers CR-01, DF-03, DF-02, DT-03, DT-03T, DT-02, F103GT, M-06, M-06 PRO, M-05, M-05 PRO, M-05 ver.II PRO, MF-01X, TT-02B, TT-02FT, TT-02RR, TT-02D, TT-02 TYPE-SR, TT-02 TYPE-S, TT-02, TT-01D TYPE-E and TT-01 TYPE-E chassis. For workshop stock, rebuilds or replacing worn wheel mounting parts, this set covers one full chassis with 4 matching hubs and pins. It suits bench work where exact chassis compatibility matters and keeps the wheel mounting hardware aligned with the specified 12 mm standard used by the listed platforms. Warning! Not suitable for children under 14 years.
Gears & motor pinions
19T Pinion Gear, model accessory, M0.6
303505049€5.69
This 19T pinion gear is a compact drivetrain part for model applications that use module M0.6 gearing. Its 19 straight teeth mesh with the matching gear stage to pass motor rotation into the transmission, making it a functional choice when a specific tooth count is needed in the drive layout. The dark metal gear body is shaped for shaft mounting, with a central round bore and a side set-screw hole visible on the part. The top surface is marked with 19, which helps distinguish this version from other tooth counts during maintenance or parts sorting. As a small mechanical component, the pinion sits at the point where motor output meets the rest of the drivetrain, so the tooth count directly relates to the gearing combination used in the model. It fits naturally into workshop tasks such as replacing a worn pinion, restoring a compatible drivetrain, or keeping a matching spare ready for service intervals. On the bench, the compact form and visible marking make it straightforward to identify alongside other transmission parts and gearing options. Warning! Not suitable for children under 14 years.
Gears & motor pinions
20/21T Pinion Gear Set, RC motor accessory, aluminum
300050356€9.99
This 20/21T Pinion Gear Set is a compact drivetrain upgrade for compatible RC chassis, pairing 2 aluminum pinions with 2 grub screws for secure mounting on the motor shaft. The 20-tooth and 21-tooth options give a clear gearing choice when replacing worn parts or adjusting the drive layout for a specific chassis setup. The machined aluminum construction keeps the focus on precise tooth engagement and clean fitment in model drivetrains that use module 0.6 gearing. One pinion is marked 20 for quick identification during setup, which helps separate the two ratios at the workbench. The set is intended for a wide spread of Tamiya platforms including M-05, M-05 PRO, M-05 ver.II PRO, M-06, M-06 PRO, WR-02, WR-02G, WR-02CB, GF-01, GF-01TR, GF-01CB, G6-01, G6-01TR and TB-05 PRO. It also supports CC-01 with 20T only, plus TA06, TA06 PRO, TA06 MS and TC-01 with 21T only. Additional chassis-specific notes are defined for several applications: DF-02 is used with 53703, F104PRO II is used with 51609, and TA07 MS is used with 51356, 51423 and 51548. That makes the set a practical spare or tuning part for keeping compatible RC cars running with the correct motor pinion combination. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
2mm C-Ring-Set, model accessory, 8-piece
300084171€2.19
This 2 mm C-Ring-Set supplies 8 matching retaining clips for model maintenance, repair work and parts replacement. The compact format suits assemblies that use small fastening points, where a C-shaped ring locks into a groove on a shaft or similar mounting point to hold parts in position. The set groups identical metal clips together, which helps when a rebuild calls for consistent replacement parts rather than mixed hardware. The open centre cutout allows each ring to snap into place on the intended fitting, making this type of fastener useful wherever a low-profile retainer is needed in a mechanical model assembly. The silver-coloured finish also makes the pieces easy to identify in a parts tray or workshop setup alongside screws, washers and other small hardware. Used as spare parts, these C-rings support routine servicing, careful restoration work and the replacement of missing retainers in existing builds. Kept in a hobby drawer, the 8-piece pack provides a practical stock of matching clips for future workshop tasks on compatible model mechanisms. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
2mm E-Ring Satz, model accessory, 15 pieces
300050588€3.09
This E-Ring Satz provides 15 matching retaining clips in a 2 mm size for model maintenance, repairs and mechanical assembly work. Each E-ring is made as a small stamped metal fastener that presses onto a grooved shaft or axle from the side, where it acts as a stop to hold mounted parts in place. The flat clip profile keeps the fastening point compact, which is useful in tight spaces around driveline and wheel assemblies. The pack suits jobs where worn or missing retaining hardware needs a direct replacement in the correct size. A 2 mm E-ring can be used wherever the assembly calls for this specification, including axle or shaft setups that carry gears, bushings or wheels. The 2 mm thickness stated in the data adds a clear reference point when matching spare hardware to an existing build. With 15 identical pieces in one set, the supply supports repeated service work and keeps consistent hardware ready for future rebuilds. On the workbench, these clips fit naturally into parts sorting trays, spare hardware boxes and routine maintenance kits for RC and scale model projects. They are especially useful when a rebuild calls for several matching retainers across multiple connection points or when a small clip needs quick replacement after disassembly. Warning! Not suitable for children under 14 years.
Screws & ball head screws
2mm/M2 Lock Nut Mini 4WD hardware set
300094690€4.99
This hardware set brings 10 compact M2 lock nuts into Mini 4WD maintenance, repair and fresh assembly work. The 2 mm format suits small threaded connections, while the lock-nut construction with a nylon insert ring is designed to hold more firmly once tightened, a useful detail on fast-moving model assemblies where vibration can work against standard fasteners. The close-fitting hex shape supports careful tool use on small parts, and the metal finish gives each nut a clearly defined edge during installation. Keeping matching M2 hardware together also helps maintain a consistent fit across repeated rebuilds, part swaps and setup changes. Because the pack contains 10 pieces, it covers multiple fastening points and leaves spares ready for later workshop use. The set is focused, simple and specific: small fastening hardware for Mini 4WD systems where the right thread size matters. On the bench, these lock nuts suit routine replacement after wear, rebuilding a chassis with fresh hardware, or keeping spare fixings ready in a parts box between race-day adjustments. They also fit neatly into a regular stock of model workshop essentials, alongside the screws, shafts and brackets used in ongoing Mini 4WD upkeep. Warning! Not suitable for children under 14 years.
Screws & ball head screws
2x8mm Differential Tapping Screws, model spare set
300050573€3.29
This spare screw set focuses on one specific workshop need: 10 matching 2x8 mm differential self-tapping screws for compatible model maintenance and repair. The uniform size keeps replacement work consistent when original fasteners are worn, missing or set aside during a rebuild, and the metal construction suits repeated use in model assembly tasks where a precise screw type matters. The domed heads use a crosshead drive, allowing the tool to seat cleanly during installation and removal. A fully threaded shaft is suited to fastening duties where the thread needs to bite along the full length of the screw rather than only near the tip. Because all 10 screws share the same format, the set supports organized parts storage and avoids mixing unmatched hardware into a differential assembly. The pack contents are stated plainly: 10 differential self-tapping screws. On the bench, this set fits naturally into routine servicing, replacement of lost fasteners, or preparation of spare hardware before a rebuild begins. It also works as a practical stock addition for model toolboxes and parts drawers, where a clearly defined 2x8 mm screw can save time during maintenance on compatible assemblies. Warning! Not suitable for children under 14 years.
Axes & drive shafts
37mm SwingShafts, RC spare part for XV-02
300051700€16.19
These 37 mm SwingShafts are a focused RC spare part for keeping compatible chassis setups running cleanly and consistently. Designed for the XV-02 chassis, they replace worn swing shafts in the assembly universal area, where accurate fit and free movement matter to drivetrain response and stable operation during repeated running sessions. Each shaft is marked A • 37 and the set supplies 2 matching parts for the same specified length. The black rod form with metal inserts at both ends reflects the compact mechanical role these parts play inside the chassis assembly. On TT-02 based cars, the shafts can also be used alongside Item 54623 and 51444 for defined compatibility. Combined with Item 54874, they also allow a wider camber angle adjustment range on the TT-02 chassis, opening more setup latitude for fine tuning suspension geometry. This kind of replacement suits regular workshop maintenance, rebuilds after heavy use, or planned setup changes between chassis configurations. In a tuning session, fresh shafts can restore precise movement in the relevant assembly area, while in a parts box they serve as a chassis-specific option for XV-02 and selected TT-02 builds.
Axes & drive shafts
39mm Drive Shaft Set, RC spare part for TT-01E
300050883€12.99
This RC spare part set provides 2 drive shafts in a 39 mm format for selected Tamiya chassis. Designed for TA-01, TA-04, TA-05 and TT-01E platforms, the shafts sit in the drivetrain where rotating assemblies need a compact link that can keep transmitting power while suspension parts move through their travel. Each shaft uses a straight center section with rounded ends and cross pins, a dogbone-style layout commonly used to connect outdrives and wheel-side drive components. That shape allows the shaft to articulate inside the drivetrain rather than acting as a fixed rod, which matters when a chassis is cornering, accelerating or running over uneven surfaces. The 39 mm dimension is the key fit point here, so matching the stated length is essential when replacing worn or missing drivetrain parts. Supplied as a 2-piece set, the pack suits paired servicing work without forcing a mixed left and right setup. In workshop use, these shafts fit naturally into rebuilds, maintenance sessions and parts-box planning for compatible touring car chassis. They also make sense as a trackside spare when a running session calls for a quick drivetrain refresh on TA-01, TA-04, TA-05 or TT-01E based models. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
3mm 5.5x5.0mm Spacer, model accessory, 10-pack
319804641€8.19
This spacer set is built around exact measurements that matter during model maintenance and parts replacement. Each piece is specified at 3 mm with 5.5 x 5.0 mm dimensions, giving a clear reference for assemblies that rely on this format to maintain the intended spacing between compatible components. The set contains 10 matching spacers, which supports repeated service work without mixing different sizes in the same build. The defined dimensions make this set useful when an existing assembly already calls for 3 mm spacers and when consistent fit across several mounting points is needed. Rather than relying on approximate sizing, the stated 5.5 x 5.0 mm format gives a direct basis for checking compatibility against the parts already in use. On the workbench, these spacers suit routine maintenance, measured replacement and keeping spare hardware ready for future adjustments. The 10-piece count also helps when several identical positions in one assembly need the same spacer size, or when matching replacements are kept in reserve for later servicing. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
3mm O-Ring black, model accessory, 10-piece
300084195€1.99
This 10-piece pack of black 3 mm O-rings adds a practical spare-parts supply for model maintenance, repair work and small mechanical assemblies. Each ring shares the same compact diameter and circular form, making the set useful wherever a matching seal or replacement ring is needed to restore fit between moving or joined parts. The pack contains 10 identical rubber O-rings, which helps keep replacements consistent across repeated service jobs instead of mixing unmatched sizes. Their black finish makes them easy to distinguish from other small workshop parts during sorting and storage. In model building and accessory upkeep, small sealing components often matter as much as larger visible parts, especially when a worn ring needs a direct like-for-like swap rather than an improvised substitute. Kept in a parts drawer, tool case or bench organiser, these O-rings are ready for routine maintenance sessions and quick repairs. The uniform 3 mm format also suits builders who prefer to keep duplicate consumable parts available before starting detailed assembly or servicing work. Warning! Not suitable for children under 14 years.
Screws & ball head screws
3mm Washer MA14, model accessory, 15-piece set
300050586€3.09
This MA14 washer set brings a straightforward supply of 15 matching 3 mm washers to the workbench, supporting model maintenance, replacement tasks and assembly jobs that call for correctly sized small hardware. The compact format suits builders who need a ready reserve for routine parts handling rather than a mixed assortment. Each washer is identified in the data as 3 mm Washer and grouped under Models Supplies, placing it clearly in the spare-parts and workshop-accessory side of model building. The 15-piece count gives a practical quantity for keeping common hardware on hand during repairs or when an existing build needs fresh fastening components. The MA14 reference helps distinguish this set from other small parts in a broader workshop stock, especially where several washer sizes may be stored together. On the bench, a dedicated washer pack like this supports cleaner preparation before assembly starts and quicker replacement when a small part is missing during maintenance. It also fits neatly into organised spares storage, where size-specific hardware can be sorted by reference and reached quickly for the next build session.
Other spare parts & accessories
3x0.7mm Aluminum Spacer Set, model accessory
309805645€6.29
These aluminum spacers in 3x0.7 mm format support accurate spacing in detailed model assembly, where a defined gap can influence fit, alignment and component position. The 10-piece pack gives a ready supply for workshop drawers, replacement needs or builds that use several matching spacers in one setup. The 3 mm size and 0.7 mm thickness make this set suited to fine adjustment work rather than broad structural filling. In model construction, spacers like these sit between mounted parts to create consistent separation and help maintain the intended position of screws, brackets or other fitted elements. Aluminum brings a clean, technical finish to this small but useful hardware format and fits naturally into precision-focused hobby work. Whether used during a fresh build, a repair or a measured setup change, the defined dimensions make selection straightforward when a specific spacing value is needed. Kept in a parts box or bench organizer, the set adds a practical option for builders who work through detailed fitting tasks one measured step at a time. Warning! Not suitable for children under 14 years.
Screws & ball head screws
3x10 Tapping Screw BK, model screw set, 10 pcs
309804392€6.19
This screw set supplies 10 black 3x10 tapping screws for model assembly, replacement work and workshop stock. The compact format suits builders who need the exact fastener type stated on a parts list or want matching hardware ready for routine maintenance on compatible models. The 3x10 specification gives a direct reference for size, which helps when sorting spare hardware for repairs or preparing parts before a build begins. The black finish supports a uniform appearance on visible fixing points where darker hardware is preferred. As tapping screws, these fasteners are intended for fastening duties in suitable model applications where this screw type is required. The pack count of 10 pieces provides a practical quantity for replacing missing screws, refreshing used fixings or keeping a small reserve in the workshop. On the bench, this set fits naturally into regular maintenance tasks such as securing parts after disassembly or replacing worn hardware during a rebuild. It also works well as a dedicated spare pack kept alongside model tools and sorted fasteners, ready when the correct 3x10 tapping screw is needed. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
3x10mm Alum. Turnbuckle Shaft, chassis accessory
300053892€11.99
These 3 x 10 mm aluminium turnbuckle shafts bring precise anti-roll bar adjustment to compatible chassis setups while adding a clear blue finish to the hardware. The set contains 4 shafts and is intended as a chassis accessory for fine tuning left and right anti-roll bar settings without removing the adjuster. The compact 3 x 10 mm dimensions suit dedicated on-road racing platforms where small setup changes matter. As a replacement for 9804250, this set gives a direct route to refreshing existing hardware with the same stated function. Compatibility is listed for TRF415MSX, TRF415MS, TB Evo. IV MS and TB Evo. IV. TA05 fitment is also specified, with the condition that adjusters must be shortened. At the workbench, these shafts support quick setup changes between runs when anti-roll bar balance needs a finer response. In regular maintenance, the 4-piece pack also helps keep a matching set ready for rebuilds, repairs or chassis-specific spares within a race box. Warning! Not suitable for children under 14 years.
Screws & ball head screws
3x12mm Counter Screw, model screw set, 10 pieces
300050581€3.29
This screw set provides 10 matching countersunk screws in a 3 x 12 mm format for model assembly, maintenance and hardware replacement. The flat countersunk head supports a flush finish on compatible parts, which helps keep surfaces even where protruding fasteners would interfere with fit or movement. The set is supplied as metal fastening hardware and suits tasks that call for the same stated size across several fixing points. A 12 mm length gives reach through compatible layered parts, while the 3 mm diameter defines the thread size for matching holes and receiving material. Because all 10 screws share the same format, the pack works well for replacing lost fasteners in groups rather than mixing different sizes during a repair. The pointed threaded shafts are shaped for fastening use, and the Phillips drive allows controlled tightening with a matching screwdriver. On the workbench, the set supports routine upkeep of model builds, spare-parts sorting and planned rebuilds where identical hardware is needed across several positions. It also fits neatly into parts storage for future service jobs, keeping a clearly specified screw size ready when a compatible assembly calls for 3 x 12 mm countersunk fixings. Warning! Not suitable for children under 14 years.
Screws & ball head screws
3x12mm Steel CS HexHead Screws, model accessory
300051631€2.79
These 3x12mm Steel CS HexHead Screws are a focused workshop accessory for maintaining compatible model and RC assemblies. The steel construction provides the specified material for replacement use, while the countersunk screw form is made to sit into matching recessed mounting points for a flush finish. Each screw uses a hex head, giving a defined tool interface for secure tightening during fitting and servicing. The pack contains 10 screws, which makes it useful for routine maintenance, repair work, or keeping matching fasteners ready in the parts box. The 3x12mm size is the key reference for checking compatibility with the intended assembly point, especially where the original build calls for the same thread and length. As replacement hardware, these screws are suited to restoring firm connections after wear, loss, or repeated disassembly during setup changes and repairs. On the workbench, they fit naturally into regular service tasks such as refreshing mounting points on a chassis, reattaching compatible sections, or replacing individual fasteners before the next run. For model builders who keep spare hardware sorted by size, this 10-piece set adds a clear, easy-to-store option for ongoing maintenance. Warning! Not suitable for children under 14 years.
Screws & ball head screws
3x15mm Tapping Screw, model accessory, 10-pack
300050583€3.39
This 10-pack of 3x15 mm tapping screws is a focused workshop spare for model maintenance, repairs and ongoing assembly needs. The exact 3x15 mm size gives a clear match point when worn, missing or damaged fasteners need to be replaced with the same format, and the TA-01 and TA-02 designation identifies the intended application directly in the part name. The set consists of 10 silver metal screws with a threaded shaft, rounded pan head and cross-head drive as shown in the product image. That head shape supports secure seating against the mounted part, while the cross-head recess allows controlled tightening with a suitable screwdriver. Keeping identical screws together in one pack helps maintain a consistent fit across the relevant fixing points instead of mixing different lengths or thread types during service work. On the bench, this kind of hardware is useful for routine chassis upkeep, replacing lost fasteners after disassembly, or keeping matching spares ready between rebuilds. For TA-01 and TA-02 based model work, the pack offers a straightforward way to restore the specified fixing point with the correct screw format.
Screws & ball head screws
3x22mm Screw Pin, model spare part, 4 pcs.
309805755€4.29
This spare-parts set provides 4 matching 3 x 22 mm screw pins for compatible model assemblies, giving a direct way to replace fastening parts that are missing, worn or no longer holding as intended. The defined 22 mm length and 3 mm format help maintain the original connection points in builds that rely on this pin size. Each piece has a long cylindrical shaft, a rounded tip, a wide head and a ringed section below the head. That shape supports guided insertion and a seated hold in the matching mounting point, while the uniform dimensions across all 4 pieces keep the set consistent for repair work. The black finish gives the parts a neutral technical appearance that blends into many model layouts and spare-parts boxes. This 4-piece pack suits routine workshop upkeep, targeted repairs and the replacement of individual fastening points on compatible models. Kept alongside other maintenance parts, the pins are ready when a build needs a like-for-like fixing part in the 3 x 22 mm size. Warning! Not suitable for children under 14 years.
Axes & drive shafts
3x23mm Turn-Buckle Shaft, RC spare part, 4 pcs
309805780€4.69
This set of 4 turn-buckle shafts in 3x23 mm format adds a precise replacement option for RC model maintenance and setup work. The metal shafts are threaded on both ends and use a compact central section that supports handling during installation, removal and adjustment inside a linkage assembly. Used in steering or similar connection points where exact length matters, turn-buckle shafts allow the assembly to be tuned by changing the effective linkage position rather than replacing the whole mechanism. The 3x23 mm specification is the key fit detail for matching an existing compatible build, and the pack of 4 provides a practical quantity for servicing paired linkage points or keeping matching spares on hand. The dark metallic finish and cleanly cut threads reflect the functional, workshop-focused character of the part. These shafts fit naturally into bench work such as replacing worn connectors, refreshing a running chassis or preparing a model for its next setup session. In a parts box, pit case or hobby drawer, a matched set of 4 helps keep compatible RC assemblies ready when a linkage needs a fast, like-for-like swap. Warning! Not suitable for children under 14 years.
Screws & ball head screws
3x5mm Flathead-Screw, model screw set, Phillips
300051211€2.89
This screw set supplies 5 matching 3 x 5 mm flathead fasteners for model building, maintenance and hardware replacement. The compact size and crosshead design make the screws easy to identify at the bench, while the flat head sits neatly against compatible parts for a clean, flush connection. Each screw has a Phillips-style drive and a short machine thread, as shown by the defined head shape and threaded shaft. That combination suits small fastening points where controlled tightening matters and where oversized hardware would interfere with surrounding parts. The set is useful when an original screw is lost during assembly, when worn hardware needs replacing, or when a matching group of fasteners is needed for a repair. The black finish keeps the hardware visually understated on many technical builds. On a workbench, these screws fit naturally into routine model care: securing a bracket, refitting a cover, or restoring a connection after disassembly. Kept alongside other spare hardware, the 5-piece pack provides a practical reserve for compatible model sections that call for the same 3 x 5 mm format. Warning! Not suitable for children under 14 years.
Screws & ball head screws
3x6mm Steel CS HexHead Screws, model hardware
300051625€2.89
These 3x6mm Steel CS HexHead Screws provide compact fastening hardware for model maintenance, repairs and fresh assembly work. The steel build pairs a countersunk head with a hex socket drive, so each screw can sit flush in a matching recess while allowing firm, controlled tool engagement during installation. In the pack are 10 matching screws, shown with a dark metal finish and short threaded shafts suited to precise mounting points. The 3x6mm size makes this hardware relevant wherever that exact thread and length are specified in a compatible model or accessory assembly. A countersunk head is used where the screw needs to settle into the surface rather than stand proud, which helps preserve clean part alignment around plates, brackets or other fitted sections. The hex socket format also reduces the chance of slipping compared with a simple slotted head when careful tightening is needed on small-scale assemblies. These screws fit naturally into routine workshop tasks such as replacing worn fasteners, securing parts after servicing, or keeping spare hardware on hand for future adjustments. On RC cars and other model builds, timely replacement of damaged mounting hardware helps maintain consistent fit at the fastening point and supports reliable running after repeated use. Warning! Not suitable for children under 14 years.
Screws & ball head screws
3x6mm Steel Hex Head Screws, model accessory
300051624€2.89
These 3x6 mm steel hex head screws are replacement fastening hardware for model maintenance, repair and parts changes. The steel construction and internal hex drive support secure tightening with a matching tool, while the compact size suits smaller mounting points where consistent hardware dimensions matter. Supplied as a set of 10, they provide a practical stock of matching screws for workshop drawers, pit boxes or spare-parts cases. The rounded head shape and fully threaded shaft are suited to refitting components that rely on small, uniform fasteners. When an original screw is worn, lost or damaged, replacing it with the same 3x6 mm format helps preserve the intended fit at the fixing point. The dark metal finish keeps the set visually consistent, and the identical sizing across all 10 pieces simplifies sorting and selection during repair work. On a workbench, these screws suit routine servicing, rebuilds and hardware replacement on model assemblies that call for this exact size. They are also useful to keep on hand as spare fastening hardware, ready for quick swaps when a repair should not be delayed by a missing screw. Warning! Not suitable for children under 14 years.
Screws & ball head screws
4 mm Adjuster M2, model accessory, 6-piece set
300050633€3.19
This 4 mm Adjuster M2 pack provides 6 matching ball pans for model maintenance, repair work and fresh assemblies that call for the same connection part throughout a linkage setup. The compact shape and M2 specification make the set a practical choice when worn or missing joint pieces need to be replaced with matching components. Each ball pan is supplied as a separate small part, so the pack can support several connection points in one project or stay on hand as workshop spares for later servicing. The 4 mm dimension gives a direct reference when matching existing hardware, while the uniform off-white moulded finish helps keep the parts easy to identify among other small model components. Scope of delivery: 6 ball pans. This set suits bench repairs, routine parts replacement and planned builds where identical linkage fittings are required across the assembly. It also works well as a stock spare for model toolboxes and hobby drawers, ready for the moment a control connection or adjuster point needs the same M2 and 4 mm format again. Warning! Not suitable for children under 14 years.
Screws & ball head screws
4 mm Serrated Wheel Nuts, model accessory, steel
300042282€4.19
These 4 mm serrated wheel nuts are made for compatible 1:10 models and bring a clean, functional solution to wheel mounting and replacement work. The steel construction gives each nut the solid threaded form needed for repeated fitting, while the serrated base increases contact at the mounting point when tightened. In the workshop or at the track, that combination supports a firm connection between wheel and axle hardware. The set contains 8 wheel nuts, making it useful for complete wheel swaps as well as keeping matching spares ready for service intervals. The compact format suits routine maintenance jobs where lost or worn fasteners need to be replaced with the correct size. The metallic finish and flanged nut shape match the hardware style commonly used on model vehicle wheel hubs, and the threaded interior is designed for direct fastening rather than decorative use. As a dedicated accessory part, this set focuses on one specific task: securing wheel assemblies with the correct 4 mm steel nut. On a repair bench, the 8-piece count supports organized replacement across multiple corners of a chassis. During rebuilds or setup changes on compatible 1:10 models, the serrated contact face helps the nut seat with a more positive mechanical hold as the wheel is fitted and tightened. Warning! Not suitable for children under 14 years.
Axes & drive shafts
44mm TRF L.F. Drive Shafts, RC spare part
300042362€22.49
These 44 mm TRF L.F. drive shafts are built for double cardan joint drivetrains that use swing shaft caps from Item 54921. The steel construction and fluorine surface coating focus on two key demands in RC driveline tuning: controlled movement at the joint and reduced friction where the shaft is working under load. Supplied as 2 matching shafts, the set supports a balanced left and right installation in compatible chassis layouts. A key update is the 10.8 mm needle pin section, which is 1 mm longer than on previous shafts. That extra length is specified to get more from swing shaft cap option parts, making these shafts a targeted upgrade for builders refining a double cardan setup rather than changing unrelated areas of the car. The LF44 marking shown on the shafts helps identify the part during maintenance or when several driveline options are kept in a pit box. In workshop use, these shafts suit rebuilds after wear, planned driveline updates, or a fresh parts selection for a compatible competition chassis. They are best matched with the stated cap system, where the longer pin section and low-friction coating can be used as intended in the assembled transmission layout.
Axes & drive shafts
45mm Drive Shafts, TRF421 spare part set
300042387€18.99
These 45 mm drive shafts for TRF421 are a focused drivetrain spare for model car maintenance, supplied as 2 matching parts for Low Friction Double Cardan Joint Shafts. The dark metal shafts are marked LF45 and use a straight shaft form with joint ends shaped for the matching assembly. At the shaft end, each part uses a 10.8 mm needle pin. This detail is specified to work together with Item 54921 Reinforced Swing Shaft Caps, with 2 pieces each for front and rear fitment. The compatibility note is narrow by design: these shafts are only for cars that use Item 54921, which keeps the replacement choice tied to the correct drivetrain layout instead of a broad universal fit claim. As a spare part set, the pair supports maintenance after wear in the transmission area and restores the intended shaft length of 45 mm on both sides. The 2-piece format suits workshop stock, scheduled rebuilds and targeted repairs on a TRF421 setup. In a bench session, the matched pair helps keep the drivetrain specification consistent when replacing both corresponding shafts in the same assembly. Warning! Not suitable for children under 14 years.
Axes & drive shafts
46 mm TRF Swing Shafts, RC accessory, aluminium
300051760€18.99
These TRF 46 mm aluminium half cardan shafts add a focused drivetrain upgrade for compatible RC chassis, combining low weight with a ball bearing mounted layout that helps the axle rotate with less friction. In running, that reduced drag supports steadier power delivery through direction changes, where speed loss at the shaft can affect how cleanly a car carries momentum. The set contains 2 lightweight 46 mm swing axles and is intended as a chassis-specific accessory rather than a universal fit part. The half cardan design suits drivetrain maintenance, replacement work and targeted tuning where the shaft assembly is a key wear point. For TRF421X use, the specification names compatibility with ball bearing set 51762 and differential joints 51764 when the shafts are installed on the TRF421 chassis 42384. That combination gives a clear reference for planning a matching drivetrain setup instead of mixing unspecified parts. On the bench, the defined 46 mm length helps identify the correct shaft format before installation. During track use, the ball bearing mounted construction supports smoother axle movement in repeated corner entries and exits, where friction control matters most in a responsive RC drivetrain. Warning! Not suitable for children under 14 years.
Screws & ball head screws
4mm Ball Connector M2, model accessory, 5-piece
300050590€3.99
This 5-piece set of 4 mm Ball Connector M2 hardware adds a compact connection point to model mechanisms that rely on precise moving links. Each connector uses a polished spherical head above a short neck, hex section and threaded post, creating a clear interface for compatible snap-on or pivoting parts in tight installation spaces. The 4 mm head size and M2 thread make these connectors suited to small-scale mechanical layouts where clean movement and accurate mounting matter. The metal construction gives each piece a defined shape for repeated fastening and removal during setup, adjustment or replacement work. The hex base supports tool-assisted tightening, while the threaded post seats into matching mounting points for a secure mechanical hold. With 5 identical connectors in the pack, the set can equip several linkage positions in one assembly or replace worn hardware across existing running gear. On the workbench, these connectors fit naturally into repair, tuning and fresh build tasks where steering links, control rods or other articulated parts need a ball-end mounting point. The consistent dimensions across all 5 pieces help keep left and right connection points matched when a model uses mirrored hardware. Warning! Not suitable for children under 14 years.
Screws & ball head screws
4mm Flange Lock Nut Bla (8), RC accessory set
300054642€3.89
This RC hardware set brings a clean wheel finish and a more secure fastening point to compatible model cars. Each 4 mm flange lock nut uses a nylon insert that grips the thread as the nut is tightened, helping the connection stay in place when the chassis is exposed to repeated vibration, direction changes and regular wheel removal. The set contains 8 blue flange lock nuts, shown as individual metal fasteners with a flanged base and visible locking ring. That flange gives the nut a broader contact surface than a plain hex nut, which helps distribute clamping force at the mounting point. The blue colour variation also changes the look of the wheel area, making it useful for refresh work on existing builds or for replacing standard hardware supplied in many RC kits. The parts are intended as accessory or spare hardware rather than a complete vehicle component group. Compatibility covers a range of touring car and off-road cars, making the set useful for workshop drawers, rebuild projects and routine running maintenance. When wheel hardware has been removed repeatedly or no longer matches the rest of the chassis, this 8-piece set provides a straightforward replacement option with a locking function built into each nut.
Screws & ball head screws
4mm Flange Lock Nut Blue, RC accessory, 5-pack
300053159€13.79
These 4 mm flanged lock nuts bring a functional hardware upgrade to compatible RC vehicle setups, combining blue anodized aluminum with a compact fastening format that trims weight and sharpens the look of exposed wheel hardware. The metallic finish stands out clearly against darker rims, suspension parts and chassis details, giving maintenance work and final setup a more technical appearance. Each nut uses a hexagonal body with a threaded center hole and a wide integrated flange. That flange increases the contact area at the mounting point, which helps distribute pressure more evenly across the wheel surface than a narrow nut alone. The lock-nut format is suited to repeated fitting and removal during tuning, cleaning and routine parts changes. With 5 matching pieces in the pack, one extra nut remains available after a standard 4-wheel installation, which is useful to keep with trackside spares or workshop hardware. The small size and clear 4 mm specification make this set easy to match with compatible wheel axles and hubs in RC maintenance or customisation work. Whether replacing worn hardware, refining the finish of a competition-inspired build or keeping a spare ready between running sessions, these aluminum nuts add a precise mechanical detail where it is seen most.
Screws & ball head screws
4mm Shift Ball Connector M3, model spare part
319804831€4.29
This 4 mm Shift Ball Connector with M3 thread is a dedicated spare part for Truck and HiLift model applications. The stated size and thread specification provide a direct reference for replacing the same connector type in an existing assembly, where the correct fit of small linkage hardware matters to the overall mechanism. Its role is focused and practical: restoring a worn, missing, or damaged connection point with the specified 4 mm ball format and M3 threading. Because the product data identifies Truck and HiLift compatibility, the connector is suited to those model ranges rather than to general, undefined use. That makes it a useful workshop part for routine maintenance, repair work, and keeping compatible builds equipped with the correct hardware standard. The compact format also stores easily alongside other model service parts, so the required connector type is ready when a rebuild or replacement is due. In a repair session, this spare part can be selected by its exact connector size and thread rather than by guesswork. For ongoing model upkeep, it supports a tidy stock of application-specific hardware for Truck and HiLift assemblies. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
4mm Shim Set, RC accessory, 0.1/0.2/0.3 mm
300053586€11.29
This 4 mm shim set brings fine mechanical adjustment to RC maintenance and model workshop tasks where shaft spacing needs a precise correction. The pack contains 30 shims in total, divided into 10 pieces each at 0.1 mm, 0.2 mm and 0.3 mm, so clearance can be tuned in small measured steps instead of forcing a single thickness into every job. Each shim fits 4 mm shafts and is intended for situations where more clearance is required. The thin ring format slips onto the shaft to change spacing directly at the point of assembly, which helps when rotating parts need a more exact position. Combining different thicknesses from the set also allows intermediate spacing values, giving more control during drivetrain setup, axle work or other moving assemblies that rely on accurate alignment. On the bench, the 3 thickness options support methodical trial fitting during maintenance, rebuilds or parts replacement. The grouped sizes make it straightforward to compare spacing changes, correct excess play and refine the fit of compatible components without replacing the shaft itself.
Screws & ball head screws
4x10mm Step Screw, spare screw set for M-Chassis
300050585€4.39
This spare screw set provides 5 matching 4x10 mm step screws for compatible model chassis work, with a compact format that suits replacement, maintenance and rebuild tasks. The stepped design combines a threaded section, a cylindrical shoulder and a domed head, so one fastener can secure a part while also maintaining the spacing that a plain screw may not provide. The data names TA02, TA03 and M-Chassis compatibility, giving a direct reference for parts matching during service work. In a workshop tray or spares box, the 4x10 mm size is easy to identify when a build calls for the same specification. The 5-piece quantity supports targeted replacement rather than forcing a full hardware change across a chassis. The metal construction fits the role of a small mechanical fastening part where repeated fitting and removal are part of normal model upkeep. This screw pack suits bench repairs, scheduled maintenance and the final stages of a rebuild when the correct shoulder screw is needed to complete a mounting point. It also works as a useful reserve for keeping compatible TA02, TA03 or M-Chassis models ready for the next running session.
Screws & ball head screws
5mm Adjuster Short, RC spare part set, 8 pieces
300054489€2.89
This spare part set brings 8 short 5 mm adjusters into the suspension area of an R/C car, where low-friction material helps linked joints move with a smoother action. Each piece is shaped for use at connection points that need a pivoting link, making it a practical choice for maintenance, worn-part replacement or a fresh chassis build that calls for matching hardware. The short format suits tighter installation points than a longer adjuster and keeps the linkage layout compact around the joint. In use, the circular eyelet opening forms the attachment point for the connected rod or pin, while the low-friction composition focuses on reducing drag at the moving interface. That can help suspension parts articulate more freely as the chassis loads and unloads through direction changes, uneven surfaces and repeated laps. The set contains 8 identical adjusters, which supports consistent fit across several matching positions on a compatible R/C car. On a workbench, these adjusters fit naturally into routine rebuilds, suspension refreshes and setup corrections where several joints need the same part at once. During running sessions, smoother linkage movement can support cleaner suspension response as the car transitions through braking, turn-in and acceleration.
Screws & ball head screws
5mm Adjuster, model accessory, 19mm length
300050596€3.49
This model accessory set supplies 6 ball pans sized at 5 mm diameter and 19 mm length for compatible maintenance and replacement work. The specified dimensions make the set easy to match against an existing assembly, especially when a worn or missing fitting needs the same connection size and overall length. The pack is intended for use with 50592, which gives a direct compatibility reference instead of leaving the fit to estimation. Ball pans sit at the connection point of linked parts, so the stated 5 mm diameter matters when selecting the correct hardware for a rebuild or service task. The quantity of 6 supports repeated replacement work across the same assembly and leaves matching spares available for later upkeep. On the workbench, this set fits neatly into routine model maintenance, whether a compatible build is being refreshed after use or a stored chassis is being brought back into running condition. The compact hardware format also makes it practical to keep alongside other small fittings for planned repairs and parts organisation. Warning! Not suitable for children under 14 years.
Screws & ball head screws
5mm Ball Connector Nut, model accessory, 4pcs
309804206€5.49
The 5mm Ball Connector Nut set supplies 4 matching threaded fittings for model assembly, repair and maintenance work. Each piece combines an internal screw thread with a hexagonal base, giving small mechanical connections a defined contact point for tightening and adjustment during a build. The compact black metal parts are shaped for clean integration into technical assemblies where consistent hardware matters. Their uniform form keeps all 4 fittings visually and mechanically aligned across the same application, which helps when replacing worn connector nuts or preparing matching hardware for a fresh setup. The 5 mm sizing gives a clear reference for compatibility within the intended assembly, while the threaded interior supports a direct fit onto the corresponding shaft or screw. On the workbench, these fittings suit routine servicing, parts replacement and detail-focused model projects that call for precise small hardware rather than mixed spare nuts. The 4-piece pack also leaves matching components ready for follow-up maintenance when the same connection point appears more than once in an assembly. Warning! Not suitable for children under 14 years.
Screws & ball head screws
5mm Ball Head M3, model accessory, 10-piece set
300050592€6.79
This 10-piece set of 5 mm Ball Head M3 parts adds a precise connection component to model maintenance, repair and assembly work. Each ball head uses an M3 threaded shaft and a 5 mm ball, a combination that suits compatible linkage and mounting points where a compact pivoting connection is needed. The metal construction and hex shoulder shown on each part support secure tightening during installation. The pack includes 10 matching ball heads, which helps keep spare hardware on hand for repeated service jobs or fresh builds that call for the same fitting throughout. The spherical head shape is suited to moving connection points that need controlled articulation rather than a fixed joint. The short threaded section keeps the mounting format specific and easy to match against existing compatible parts. The gold-coloured finish shown in the set also makes each piece easy to identify in a parts tray or workshop drawer. On a repair bench, these fittings suit the replacement of worn connection points on compatible models. During a new build, the matching 10-piece quantity supports consistent hardware selection across multiple mounting positions and leaves reserve parts available for later maintenance. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
5mm Body O-Rings, model accessory, 10 pieces
300054384€3.09
These 5 mm body O-rings are small model accessory parts that make a visible difference at the body mounts. Fitted to body mount rods, they allow fine height adjustment of the bodyshell position, so the shell can sit with a more controlled fit on the chassis during setup. The set contains 10 O-rings for replacement stock or fresh installation on compatible body posts. Their role is not limited to spacing: each ring also provides a cushioning effect between the bodyshell and the mount point. On rougher driving surfaces, that added cushion helps reduce body chatter that can appear when the shell moves against the posts over bumps. This gives the shell mount a tidier, more settled feel while the model is running. In workshop use, the rings are easy to keep on hand for routine maintenance, rebuilds, or shell changes between different bodyshell setups. They suit drivers who fine-tune shell height on body mount rods and want spare mounting hardware ready for regular track or car park sessions. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
5mm Shim Set, RC accessory, 0.1 0.2 0.3mm
300053587€11.29
This 5 mm shim set brings precise spacing control to RC chassis work, with 3 thicknesses at 0.1 mm, 0.2 mm and 0.3 mm for fine mechanical adjustment. Used at 5 mm fitment points, the shims help take up excess movement where a cleaner, tighter setup is needed around suspension parts or wheel axles. The set includes 30 shims in total, arranged as 10 pieces of each thickness, which supports repeated setup changes without relying on a single size. Small spacing differences can change how parts sit against each other, and these thin rings make those corrections measurable rather than improvised. On a maintenance bench, they can be selected to match the amount of free play present at a given point. On a fresh build, they support more exact placement of moving parts before the chassis goes into use. The shim assortment suits both on-road and off-road Tamiya vehicles, so the same pack can serve different running platforms in one workshop. Whether the goal is tidying axle movement, refining suspension fit or keeping a race chassis more closely adjusted, the 5 mm format gives a compact tuning part that earns its place in a spares box.
Screws & ball head screws
5mm/M3 Ball Socket Set, model accessory, 8 pieces
300050875€5.99
This 5 mm/M3 ball socket set brings a straightforward replacement option for compatible model linkages, with 8 matching parts ready for maintenance, repair work or a fresh build. The rod-end style shape and circular socket opening suit connection points that rely on a compact joint with controlled movement. Each piece is formed as a small connector end with a faceted outer body, a cylindrical shaft and a socket head that pairs with the stated 5 mm/M3 specification. That combination helps when an existing setup needs the same dimension rather than a close substitute. The pack format keeps several identical parts on hand at once, which is useful when multiple joints on one chassis use the same fitting or when spare hardware belongs in a regular bench stock. The black finish keeps the set visually consistent with many technical assemblies without drawing attention away from the surrounding components. In workshop use, the set fits naturally into routine servicing after wear at steering or suspension connection points. It also suits rebuilds where matching linkage ends across several rods help keep the assembly consistent and easy to sort during installation. Warning! Not suitable for children under 14 years.
Screws & ball head screws
5x9mm Ball Connector, model accessory, 5 pcs.
309805611€7.89
These 5x9 mm ball connectors add a compact mechanical link point to RC and model assemblies where a threaded joint and a smooth pivot surface need to work together. Each piece combines a 5 mm ball, an M3 threaded shaft and a 9 mm length, creating a clear fit for linkage tasks that depend on accurate spacing and dependable attachment. The polished metal finish and defined ball shape suit moving connections such as steering rods, suspension joints or other articulated model hardware, while the hexagonal shoulder provides a practical grip area during fitting. With 5 matching connectors in the pack, the set supports fresh builds, maintenance work and the replacement of worn fastening points. The small format also makes these parts useful for keeping workshop drawers or field boxes stocked with commonly needed RC hardware. In a chassis rebuild, the connectors can be fitted where rods or jointed parts need a threaded anchor and a pivoting contact point. On the bench, the uniform dimensions help keep left and right linkage positions consistent when several matching connection points are required in the same assembly. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
6 mm Shim Set, model accessory, 0.1 0.2 0.3 mm
300053726€16.29
This 6 mm shim set brings precise spacing control to model assemblies that need a cleaner fit on 6 mm shafts. With 3 thicknesses at 0.1 mm, 0.2 mm and 0.3 mm, the set supports small corrections where mechanical play affects alignment, rotation or part position. The set contains 30 pieces in total, arranged as 10 shims of each thickness. That spread makes it possible to compare different spacer combinations during a build or while servicing an existing model, instead of working around a single dimension. The thin shim format suits jobs where only a fraction of a millimetre is needed to correct end float or reduce unwanted movement between parts. Used singly or in combination, the spacers help adapt the fit to the exact requirement of the assembly point. On the bench, the set suits gearbox work, axle spacing and other 6 mm shaft applications where measured adjustment matters. As a compact workshop supply for model maintenance, repair or fresh assembly, it adds a practical range of fine spacer sizes that can be kept ready for repeated mechanical setup tasks. Warning! Not suitable for children under 14 years.
Axes & drive shafts
A-Parts Axlehousing CC-01, spare parts set
300005519€22.79
A-Parts Axlehousing CC-01 is a spare parts set for the CC-01 platform and is listed as parts for 58132. The black injection-molded runner carries several unused structural components in one frame, including axle housing style sections and mounting pieces that support a clean replacement job when original parts need to be swapped. The molded layout keeps each piece attached until removal, which helps with identification before assembly and reduces mix-ups between similar shapes. The visible parts include long housing sections, bracketed elements and a larger case-like component, all formed with mounting holes and connection points that suit chassis or drivetrain installation. Because the pieces come as a matched set on one sprue, builders can replace damaged sections with components produced together rather than mixing unrelated leftovers from a parts box. This kind of spare set fits naturally into bench maintenance, rebuild work and parts sorting between running sessions. When a CC-01 chassis needs fresh housing components after wear or breakage, the set provides the specific molded forms needed to return the assembly to working order.
Other spare parts & accessories
A-Parts Gearbox F/R 58370, RC spare parts
300004432€14.29
This A-Parts sprue is made for the 58370 and provides black injection-molded components for the gearbox F/R area of the DF-03. The unassembled runner groups housing halves, covers and structural sections in one set, giving repair work a direct route back to the intended drivetrain layout. The molded pieces show reinforced ribs, screw holes and cylindrical shaft or bearing mounts that matter when a transmission case needs its original geometry. A larger frame-like section with elongated slots adds another chassis-facing support element, while rounded shell parts serve as protective case sections around moving drivetrain parts. Because the components are supplied on the sprue, each shape stays clearly separated until preparation begins, which helps with part checking before installation. The glossy black finish matches the technical look of many RC chassis internals. This spare parts set suits maintenance benches, rebuild projects and targeted gearbox repairs where damaged housings, brackets or covers need replacement with matching forms. It also supports keeping a DF-03 running with dedicated structural parts on hand for future service work.
Other spare parts & accessories
Alligator Clip for P. Stand, model tool set
300074528€5.99
These alligator clips add a simple, controlled way to hold small model parts while cement or paint dries. The spring-loaded hinge and serrated jaws grip components firmly, so freshly finished pieces can stay separated from the work surface and remain easier to handle during careful bench work. Each pack contains 4 matching clips, which supports parallel work on several parts in the same session. The oval wire loop at the end of each clip provides a clear connection point for mounting on a compatible stand. The clips are intended for use with the Painting Stand, Work Stand and Bottled Paint Stand named in the product data, making them a practical addition for painting, gluing and drying steps where direct hand contact can disturb a finish. On a model bench, the clips can hold newly cemented sections while joints set, or keep painted components raised and separated between coats. Their compact metal form suits detail-focused tasks where small parts need a temporary grip point and a cleaner path through finishing work.
Shock absorbers & springs
Alum. Damper Retainer -1mm, RC part, blue anod
300053876€27.99
The Alum. Damper Retainer -1mm is a suspension tuning part for compatible RC chassis, combining machined aluminum construction with a blue anodized finish and a precise fit around the damper spring area. By lowering the spring set position by 1 mm compared with the aluminum mount of the OP595TRF shock, it supports a lower vehicle height and a more exact starting point for chassis setup. This set contains 4 spring plates for matched installation across the suspension. The rigid aluminum holder is made for reliable initial adjustment of the damper spring, helping setup changes translate more directly at the shock. Compatibility extends beyond the main chassis list: on TD4 and TD2 chassis, only standard front dampers can be installed. On MF-01X chassis, use with 42102 or 42273 or 42354 or 42355 or 54000. On F104 and F104W chassis, use with 53901. In workshop use, the 1 mm change gives a concrete option when refining stance and spring preload on touring, formula, or off-road based builds that share these chassis families. The 4-piece set suits rebuilds, replacement work, or a fresh suspension setup where consistent hardware across the dampers matters. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Alum. Turnbuckle Wrench blue, model tool, 3.0 mm
300053602€14.99
The Alum. Turnbuckle Wrench blue is a dedicated model tool for fine setup work on vehicles with 3 mm adjustable tie rods or camber rods. Its 3.0 mm clamping axle format is made to engage the turnbuckle directly, so alignment changes can be made with a controlled hand movement at the workbench between runs or during a full chassis service. The blue aluminum handle combines low weight with a firm feel, and the ribbed cylindrical shape supports stable finger placement while small adjustments are made. A forked open-end tip slides around the rod section to apply leverage where a standard wrench would be too bulky. This focused shape suits RC maintenance jobs where steering links and camber rods sit close to surrounding parts. The scope of delivery contains 1 clamping axle wrench. On a tuning bench, in a pit box, or beside a partly stripped chassis, this tool supports repeatable suspension and steering setup work without taking extra space. It also works well as a dedicated addition to a model building tool roll where 3 mm linkage hardware is adjusted regularly. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
Aluminium Shock Absorbers, 55.62 mm, 2-Piece Set
300053155€51.99
These aluminium shock absorbers bring a low-friction damper setup to compatible Tamiya M chassis models, combining a machined cylinder interior with a 55.62 mm overall assembled length. The metal damper design is intended for smooth operation, giving the suspension a more even response as the shafts move through the cylinder. Compatibility covers the M-06 chassis, M-06 PRO chassis, M-05 ver.II PRO chassis, M-05 chassis and M-05 PRO chassis. The set contains 2 shock absorbers and is supplied with 48 pieces for assembly, including the hardware and sealing parts needed for the damper build. Aluminium bodies, coil springs, shafts, rod ends, clips and rings form a detailed suspension set that suits replacement, rebuilding or chassis tuning work on the listed platforms. Mounted on a compatible M chassis, the dampers support controlled suspension movement during cornering, braking and direction changes. The purple finish gives the underbody a distinctive technical look, while the complete 2-piece configuration fits neatly into workshop sessions focused on maintenance, setup changes or restoring smooth damper action. Warning! Not suitable for children under 14 years.
Spare parts for old cars
Aluminum 4mm Lock Nut Set, model accessory, pink
319804624€7.19
This set of 4 aluminum lock nuts brings a precise fastening detail to model builds and maintenance work, while the pink anodized finish adds a bright visual accent at the wheel area. With a 4 mm size, the nuts suit compatible threaded axles where compact hardware needs to stay easy to handle during setup and part changes. The lock nut design is made for fastening tasks where vibration and repeated removal matter, making the set useful for routine servicing as well as colour-coordinated upgrades. Aluminum gives each nut a light metal construction that fits neatly into performance-focused builds without adding bulky hardware. The pink finish is more than a colour note on the parts tray: it helps distinguish this set quickly from standard silver or black fittings during bench work. Supplied as 4 matching pieces, the set covers one complete wheel mounting point on many model layouts. On the workbench, these nuts fit naturally into rebuilds, wheel swaps and detail updates where small hardware shapes the final look as much as the mechanical fit. They also suit spare-parts storage for regular running sessions, keeping a matching set ready when worn or misplaced fasteners need replacement.
Other spare parts & accessories
Antenna for 56019, model accessory, 175 mm
305365011€4.49
This antenna for 56019 is a dedicated model accessory with a stated length of 175 mm, intended for use where the matching reference calls for this exact part. The slim rod format gives the model a clean, defined finishing detail while keeping the replacement focused on the named application rather than a generic spare. The part is supplied as 1 piece and is described simply as an antenna for 56019, which keeps selection clear when a specific replacement is needed. The visible form shows a long metal rod with shaped ends, including a hooked bend at one end and a coiled section at the other, indicating a functional mounting or connection point within the matching model setup. That concrete shape matters when replacing a missing or bent antenna, because the end form can be just as important as the overall length. Used on the correct model, this 175 mm antenna suits repair work, parts replacement, or the completion of an existing build that needs the specified external component. It fits naturally into workshop tasks such as restoring a stored model, replacing a worn original, or finishing a project with the named 56019 reference in mind. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Antenna Pipe 300mm, model accessory, black
306095010€0.79
This black antenna pipe adds a neat, functional finishing detail to compatible RC model setups. With a length of 300 mm or 30 cm, the tube gives the antenna a defined route and helps maintain a clean layout above the body where a loose wire would look untidy. The straight tube form makes it useful as a replacement part in routine maintenance, after repairs, or when refreshing an older build with worn running hardware. Its single-purpose design keeps the fit straightforward: the pipe sits in the model's antenna mount and supports the aerial in an upright position. The black finish keeps the look understated, which suits a wide range of body colours and chassis layouts without drawing attention away from the model itself. In workshop use, a spare antenna pipe is a practical part to keep alongside other RC maintenance essentials, especially for builds that still use a visible aerial tube. It also suits restorations where small external details help return a model to a complete, ready-to-run appearance. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Antenna Pipe 380mm, model accessory, clear
306095001€0.89
This clear antenna pipe is a straightforward model accessory for RC setups that use an external aerial guide. With a length of 380 mm, it provides a long tube that can be fitted and trimmed to match the required antenna height on the model, keeping the wire routed in a visible, upright position above the bodyshell. The transparent finish leaves paintwork, markings and body lines unobstructed, which helps preserve the look of the completed model while still making the antenna route easy to follow during fitting. Supplied as 1 piece, it works well as a direct replacement for a damaged tube or as a spare kept on hand for workshop use. The simple tube format also makes it useful across routine maintenance tasks where a clean, correctly sized aerial guide is needed. On the bench, the 380 mm length gives enough material for model-specific adjustment before final installation. During transport, storage and running sessions, the fitted tube helps keep the antenna wire guided consistently instead of leaving it loose around the shell area. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Anti-Wear Grease 3g, model lubricant tube
300053439€12.991 kg = €4,330.00
Anti-Wear Grease in a 3 g tube supports smooth maintenance work on model drivetrains by combining high viscosity with precise placement. On differential gears, shafts and drive axles, the grease adheres well to rotating parts, so lubrication stays where the mechanism needs it during repeated movement. The formulation is described for model vehicles and is supplied in a compact tube with a fine, narrow nozzle for controlled dosing on small contact points. That narrow outlet helps place a small amount directly onto gear teeth, axle sections or shaft ends instead of coating surrounding areas. The grease is temperature stable and retains its viscosity over a wide temperature range, which helps keep application characteristics consistent as moving parts warm up in use. The supplied quantity is 3 g, making it suited to targeted servicing rather than bulk workshop filling. In regular upkeep, the tube fits neatly into a field box or bench drawer and is ready for quick drivetrain attention between runs. It suits focused lubrication tasks on compact assemblies where accurate placement matters, especially around differentials and other enclosed rotating components. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
Axle Spring (2) 58416, model spare part
309805304€0.89
Axle Spring (2) 58416 is a model spare part for the axle area, supplied as a 2-piece spring set under the stated 58416 designation. The format suits maintenance tasks where a matching replacement is needed for a worn, missing or no longer usable spring in a compatible model assembly. The focus here is clear part identification rather than broad fit claims. The ShortDescription names the component as an axle spring, and the pack count confirms 2 springs in the set. That makes the set useful for organised parts storage, planned servicing and direct replacement work where the correct designation matters. In a workshop drawer or spares case, the numbered reference helps separate this spring set from gears, shafts, screws and other maintenance components. During repair or upkeep, a dedicated replacement spring set can help return the axle section to its intended mechanical role in the assembly. The compact 2-piece format also suits keeping a matched pair on hand for future service jobs on compatible model builds. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Axle Spring (2), spare part for model chassis
309808008€2.99
This set of 2 axle springs is a dedicated spare part for 58347 and is shaped for mechanical return action at the axle assembly. Each spring is formed from silver-coloured metal wire and uses a tightly wound coil with one short straight leg, one longer angled arm and a small loop at the end, making the part easy to identify during maintenance. The geometry shown in the part itself matters: the coiled section stores torsion, while the two arms transfer that force back into the moving mechanism. That makes these springs suitable for restoring rotational resistance, return tension or repositioning in the intended axle location on a compatible model. Supplied as a matching pair, the set supports like-for-like replacement where both sides of an assembly use the same spring form. For workshop use, the clear standalone shape helps with part checking before fitting and with replacing worn, bent or missing hardware in an existing chassis setup. As a model spare part rather than a general hardware spring, it is best used where the 58347 fitment and the pictured form match the original assembly requirement. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
B-Parts Gearbox Super Clod Buster spare parts
300005294€19.49
B-Parts Gearbox Super Clod Buster 58321 is a replacement sprue for model maintenance and repair, bringing key transmission-area components together in one clearly structured set. The black injection-moulded frame presents the parts in their original grouped layout, which helps with visual checking before each piece is removed and installed. The sprue shows 2 large matching housing halves, a rounded cover plate, 2 circular discs with evenly spaced holes, a larger curved cover piece, and several smaller link arms and connectors. One housing half features an integrated cylindrical section, indicating a dedicated enclosure area within the gearbox assembly. The opposite half carries reinforcing ribs and multiple screw points, giving the rebuilt section the same shaped mounting structure as the original part set. Small moulded part numbers are also visible on the frame, which supports part recognition during a careful rebuild. This spare-parts set suits workshop use when a Super Clod Buster gearbox section needs replacement after wear, damage or a detailed restoration. It also helps keep a rebuild consistent by supplying matching moulded pieces from the same B-Parts group rather than mixing unrelated components.
Spare parts for old cars
Ball Bearing Set Hornet Grasshopper Chassis
300054997€17.19
This ball bearing set brings together 10 replacement bearings for a focused chassis service job across several classic Tamiya platforms. The pack contains 9 x 1150 ball bearings and 1 x 850 ball bearing, matching the sizes stated for the supported models and giving a clear route to replacing worn rotating parts with the correct mix. The set is intended for Hornet, Grasshopper, Grasshopper II, Super Storm Dragon, CW-01 chassis models such as Lunch Box, plus Mad Bull, Mad Fighter and Rising Fighter. Ball bearings sit at rotating points where shafts and axles need controlled movement, so the correct size matters as much as the quantity. The metal construction and ring design suit maintenance work on running gear and transmission areas where smooth rotation is needed. As a dedicated bearing pack rather than a mixed hardware assortment, it keeps the service task focused on the exact bearing types named in the data. It suits routine rebuilds, repairs after extended running, or planned upgrades on compatible chassis already on the bench. Kept in a workshop drawer or parts case, the 10-piece mix gives a ready reference for several well-known buggy and CW-01 based models when replacement bearings are due.
Other spare parts & accessories
Ball Differential Grease 10g, RC lubricant
300053042€11.39
Ball Differential Grease 10g is a dedicated lubricant for ball type differential gearing in RC model vehicles, supplied in a compact tube with an applicator nozzle for controlled placement on small drivetrain parts. The 10 g fill gives a practical amount for routine servicing, whether the differential is being refreshed during a rebuild or maintained between running sessions. The grease is specified for differential use rather than general-purpose lubrication, which keeps the copy focused on the part it is made for. The supplied tube format helps direct the grease into tight mechanical areas where ball differential components need careful coverage. Compatibility notes in the data reference a wide range of chassis families when used with the stated related parts, including XV-01, XV-01T, XV-01 PRO, M-07 CONCEPT, M-08 CONCEPT, TA06, TA06 PRO, TA06 MS, TT-02, TT-02D, TT-01 TYPE-E, TT-01D TYPE-E, TT-02RR, TT-02FT, TT-02B, MF-01X, M-05, M-05 PRO, M-05 ver.II PRO, M-06, M-06 PRO, DT-02, DT-03 and DT-03T. On the bench, the narrow nozzle supports precise application during drivetrain maintenance, helping keep grease where the ball differential needs it instead of spreading it across surrounding parts. In workshop use, the small tube stores easily with other RC service supplies and is ready when a ball diff setup is due for fresh lubricant. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Basic File Set Smooth Dbl. Cut(3), hobby file set
300074104€8.29
The Basic File Set Smooth Dbl. Cut(3) brings 3 distinct file shapes into one compact bench set for shaping, smoothing and refining small model parts. Flat, round and semi-circular profiles make it easier to match the filing surface to the contour being worked, whether the task is cleaning an edge, opening a curve or evening out a narrow recess. Each file is 140 mm long, with a 2.5 mm handle diameter that suits close hand control on detailed work. The double-cut surface uses 38 cuts per cm, giving the files a fine, even bite that supports a smooth finish rather than heavy stock removal. This makes the set especially suited to surface preparation on plastic scale models, while still handling Mini 4WD parts and selected metal areas where careful finishing matters. At the workbench, the different profiles help move from straight runs to rounded sections without switching to oversized tools. Black rubber grips keep the hold consistent during short filing passes, and the included vinyl case stores the 3 files together between build sessions and transport.
Gears & motor pinions
BB-01 48 Pitch Spur Gear 86T, RC spare part
300051714€4.59
The BB-01 48 Pitch Spur Gear 86T is a dedicated RC spare part for drivetrain setups that use a 48 pitch gear standard. Its circular toothed form and 86-tooth count define how it meshes with the matching pinion, making it a precise choice when a worn transmission part needs replacement or a specific gearing ratio is required for a build. This pack contains 1 spur gear. The part is intended for use with a 48 pitch pinion gear, so the tooth profile stays within the same pitch system across the gear mesh. That matters during maintenance and rebuild work, because matching pitch standards help the teeth engage correctly during rotation. The gear is shown as a molded component with a central mounting hole and reinforced face structure, details that support its role as a fitted mechanical part rather than a general workshop accessory. In practical use, the gear suits bench repairs, scheduled part changes and drivetrain refreshes on various R/C cars that accept this specification. When an RC chassis calls for an 86T spur gear in 48 pitch format, this part provides a direct, clearly defined replacement to keep the transmission setup on the intended gearing standard.
Axes & drive shafts
BB-01 D-Parts Suspension Arms, chassis spare set
300051713€12.79
The BB-01 D-Parts suspension arm set supplies the core chassis pieces that guide wheel movement at both the front and rear of a BB-01 build. With 2 front arms and 2 rear arms in the pack, the set supports a matched replacement across both ends, keeping the suspension layout consistent when worn or damaged parts need changing. Each arm is molded in glass fiber-reinforced nylon, a material choice suited to detailed chassis parts with hinge-pin mounts and outer pivot points. The shared right and left component shape reduces sorting during maintenance, since the same form is used on both sides. The included D-Parts for the BB-01 chassis focus on the mechanical areas that control suspension travel and the connection points around the wheel assemblies. This set fits workshop use, routine upkeep, or a rebuild after hard off-road sessions with a BB-01 machine. It also works as a practical spare to keep alongside other chassis parts, ready for quick replacement when the front or rear arm assemblies need attention.
Shock absorbers & springs
BB-01 Damper Adjuster V Parts, RC spare set
310225338€6.49
The BB-01 Damper Adjuster V Parts set brings front and rear damper adjuster components together on one black molded sprue for focused repair and maintenance work. Shaped rings, collars and linking pieces are arranged as separate numbered sections, so the required part can be identified before removal and fitted where the BB-01 chassis calls for it. The visible sprue layout supports clean handling at the bench, with each molded section kept in place until use rather than arriving as loose pieces. This format helps when comparing part shapes, checking orientation and separating only the needed component during a repair. The set belongs to the model supplies category and is intended for RC and model servicing rather than stand-alone play. Its compact collection of adjuster parts concentrates on one chassis area, which keeps replacement work specific instead of relying on mixed universal hardware. On a workshop table, the numbered sprue can be checked against the relevant build stage or service task before installation. For an existing BB-01 build, the set provides a direct source for renewing front or rear damper adjuster parts when the original pieces need replacement.
Axes & drive shafts
BB-01 Dogbone Shafts, RC spare part, steel
300022068€18.99
These BB-01 Dogbone Shafts are a dedicated steel spare part for the BB-01 chassis and supply a matched pair for drivetrain service. The 2 shafts use the classic dogbone layout, with a pinned ball end on one side and a cup-style joint end on the other, so rotational force can pass between connected drivetrain parts while suspension movement changes the working angle. Crafted in carbon tool steel, the shafts focus on the part of the drivetrain that sees repeated motion under load. The black metal finish and the identical left and right pieces shown in the set make them suited to a like-for-like replacement when an existing pair needs renewal. As a chassis-specific component, the fitment stays tied to the BB-01 platform rather than a broad universal range, which helps keep maintenance accurate and parts selection straightforward. On a bench build, repair session or routine drivetrain refresh, this 2-piece set covers the shaft pair in one pack. It suits keeping a running chassis in service, replacing worn transmission links, or preparing spares for future maintenance on BB-01 based RC vehicles.
Axes & drive shafts
BB-01 Front Upright Set, RC spare parts, 2 pcs
300051712€7.19
The BB-01 C-Parts front upright set supplies 2 replacement components for the front end of a BB-01 chassis, giving RC model maintenance a direct way to renew a key mounting area. Each upright is molded in glass fiber-reinforced nylon, a material choice that suits parts handling steering pivot loads, wheel support points and repeated workshop fitting. The set uses the same component shape for right and left, which simplifies parts identification when a front corner is being rebuilt. The large circular opening in each upright forms the bearing seat area, while the molded mounting points connect with the surrounding chassis hardware. As C-Parts for the BB-01 platform, these pieces belong to the chassis structure itself rather than to bodywork or trim, making them relevant for repair, upkeep and keeping an existing build in running condition. On a bench setup, the pair can replace worn, damaged or missing originals during a front-end refresh on a BB-01 model. The 2-piece format also suits keeping matching spares on hand for routine service, especially when steering and wheel support components need to be exchanged as a pair.
Other spare parts & accessories
BB-01 Main Chassis, RC spare part for BBX
319335893€21.29
The BB-01 Main Chassis is the core frame section for BBX 58719 and provides the shaped base around which the vehicle layout is built. Its black molded form combines an elongated tub design with a large central compartment, creating dedicated space for the main internal installation while keeping the underside profile structured by integrated ribbing. Across the frame, molded screw posts and cylindrical mounting areas define where matching assemblies attach, while rectangular side slots add further connection points along the chassis walls. The one-piece construction keeps the geometry consistent across the length of the frame, which matters when replacing a worn or damaged base on an existing BB-01 build. The underside view shows a symmetrical layout with reinforcement lines running through the tub, giving this spare part the form needed to carry the rest of the chassis hardware in its intended position. This replacement part suits repair work, rebuilds and parts-based restoration of a BBX 58719 using the BB-01 platform. It fits naturally into workshop sessions focused on bringing an RC vehicle back into running condition or preparing a fresh chassis foundation for the next stage of assembly.
Axes & drive shafts
BB-01 T Parts, rear suspension mount set
319225237€14.29
The BB-01 T Parts rear suspension mount set is a focused replacement and maintenance set for the specified suspension area, giving builders the exact molded shapes needed for work on the rear mounting section. The sprue format keeps the components together in one organized frame until removal, which helps with part identification before fitting begins. The visible layout includes multiple molded pieces in black and dark gray, with each shape formed for a technical role within the assembly rather than as a generic mixed parts pack. Numbered positions on the runner support orientation during workshop handling, and the molded frame format helps keep smaller connectors and bracket-style pieces grouped before installation. This makes the set useful when a damaged mount section needs renewal or when a build calls for the named BB-01 rear suspension area to be rebuilt with matching parts. On the bench, the set suits careful repair sessions, planned maintenance, or keeping key replacement parts ready alongside an existing BB-01 build. It also works well as workshop stock for model owners who prefer to keep the specified suspension mount section serviceable with the correct dedicated parts.
Gears & motor pinions
Bevel Gear Differential Set, RC spare part kit
300050602€5.99
This bevel gear differential set is a drivetrain spare part kit for selected RC chassis, built around the internal mechanism that distributes drive through a differential assembly. Supplied as a kit version, it provides 8 pieces for differential service on compatible platforms and suits repair work that focuses on the gear internals rather than the complete chassis. The set is specified for CR-01 and DT-02 chassis, making it a targeted choice when those platforms need matching replacement parts in the differential area. The included contents are 1 bevel gear differential set with 8 pieces. Studio imagery shows the internal layout clearly, with larger bevel gears, smaller mating gears, a 3-armed carrier and 2 flat washers or shims, all centered on the gear action inside the assembly. That component mix supports rebuilds where worn or damaged internal differential parts affect drivetrain function. In workshop use, this kind of set suits routine maintenance, repair after heavy running, or a planned refresh of the axle internals on a compatible chassis. It is not available for XB models, so the fit remains tied to the listed chassis platforms and their matching differential setup. Warning! Not suitable for children under 14 years.
Axes & drive shafts
Bevel Pinion Gear, spare part for model drivetrain
305455040€3.59
This bevel pinion gear is a dedicated spare part for model drivetrain service, built to pass rotational force through an angled gear interface inside a transmission assembly. The compact metal component combines a toothed upper edge with a conical body, making it suitable for mechanical layouts where direction changes within the drive line are required. Reinforced rib-like shaping along the gear body adds structural definition to the part itself, while the central mounting opening is formed for installation on a shaft or axle. That layout supports correct positioning within the surrounding mechanism and helps restore clean meshing when an original gear shows wear or damage. Supplied as 1 individual gear, it suits selective replacement work where only the affected transmission element needs to be exchanged. The plain silver-gray finish keeps the mechanical form easy to identify during maintenance and parts sorting. In workshop use, this spare gear fits repair jobs on model assemblies that rely on compact internal power transfer between connected drivetrain parts. It also serves as a practical replacement to keep an existing build in running condition after wear in a heavily used transmission section. Warning! Not suitable for children under 14 years.
Gears & motor pinions
Bevelgear Set, model spare parts for drivetrain
319440510€5.19
This bevelgear set brings the key transmission parts needed for focused drivetrain maintenance on compatible model assemblies. The set contains 5 metal gears: 2 larger bevel gears with central bore openings and 3 smaller pinion-style bevel gears with short shafts. Their angled teeth are made to mesh at intersecting shaft positions, a layout commonly used to redirect rotary motion through a compact gearbox section. The combination of larger hub gears and smaller pinions supports replacement work where worn or damaged gear teeth can affect smooth running. Because bevel gears transfer motion across a change in shaft direction, they are suited to mechanical areas where drive needs to turn through an angle rather than continue in a straight line. The silver-gray metal construction gives each gear a clearly defined tooth profile and a technical finish that matches the functional role of these parts. Compatibility is stated for BB18, BB19 and BB20, with reference to 58618 Mt.Bee. On the workbench, this set suits planned servicing, targeted repair, or keeping essential transmission parts ready for a compatible model. The clearly differentiated gear sizes also help when matching the correct meshing pair during maintenance and reassembly. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Body Mount Extension Set 5.5 mm, RC car accessory
300054604€7.99
The Body Mount Extension Set 5.5 mm adds a precise height correction to RC car body posts when a different bodyshell calls for more clearance. Each extension piece is designed to work with 5.5 mm to 6 mm diameter body mounts, and the included snap pins lock the selected position through the adjustment holes for a firm mechanical hold. Inside the set are 4 body mount extensions, plus 4 snap pins in 6 mm and 7 mm sizes. The parts are intended for touring car chassis and M-Chassis cars, where body posts may already have been cut down for another shell. Instead of replacing the full mount, this set extends the existing post by 5.5 mm and keeps the mounting point usable for another body setup. The fitting method shown in the leaflet uses the extension on the chassis-side body mount and secures it with a snap pin through the cross hole. This accessory suits workshop adjustments, shell swaps and rebuilds where body height needs a small, exact correction rather than a full change of mounts. It is compatible with TT-01, TT-02, TA05, TA06, TB-03, TB-04, XV-01, FF-03, M-05 and M-06 chassis body mounts, making it a practical addition for keeping several RC car bodyshells in rotation.
Other spare parts & accessories
Body Mount Plate BH 7/8, model accessory set
319808269€11.49
The Body Mount Plate BH 7/8 is a model accessory set for the 58441 and 58452 references named in the data. With 2 mounting plates included, it supplies the specific hardware needed for work on the body mount area, whether the goal is replacing an existing part or completing a matching assembly step on the intended build. Each plate is shown as a formed metal component with a rectangular profile, rounded corners, 2 screw holes and a shaped center section. Those details matter during installation, because the hole positions and stamped form help the plate sit in the intended location and connect with the surrounding structure as designed. The BH 7/8 designation keeps the part identification aligned with the named application, which is useful when sorting spares for maintenance or rebuild work. The compact hardware format also makes this set a focused choice when only the mounting section needs attention rather than a wider parts replacement. On a workshop table, the 2 plates can be set alongside the target chassis parts and matched directly to the specified 58441 or 58452 build. For routine upkeep, rebuilds or parts sorting, this set keeps the replacement task centered on the exact mounting hardware named in the data. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Body Mount Set, RC spare parts for DT-03 chassis
300050855€9.99
This E-parts body mount set is made for selected RC chassis and supplies the core parts needed when body fixing points need replacement. It fits DT-03, DT-03T, G6-01, G6-01TR, TL-01, FF-02 and WR-02 applications named in the data, combining molded mounts with matching hardware for a direct service task at the shell mounting area. The black components are shaped for chassis attachment and body support, while the included mounting material covers the fastening work tied to this set. Multiple hole positions on the molded parts allow the mounting point to be set according to the chassis layout and shell position, which matters when replacing worn posts or correcting body fit after use. As E-parts, these components suit maintenance benches, rebuilds and parts boxes where chassis-specific replacements need to stay close at hand. The set works well during routine RC upkeep, after a cracked mount, or when a stored chassis is being returned to running condition with the correct fixing parts. In workshop use, the combination of mounts and screws keeps the repair centered on one compatible set instead of mixing unmatched hardware from different spares. Warning! Not suitable for children under 14 years.
Axes & drive shafts
BT-01 C Parts, wheel axle spare parts set
300051732€6.99
The BT-01 C Parts set supplies original replacement components for the BT-01 chassis, centering on wheel axle and centre shaft parts used in the drivetrain. Differential cup joints, axle shafts, dogbone shafts and propeller shaft joints are grouped on one sprue, giving a direct source for matching parts when a running chassis needs repair or a rebuild calls for fresh hardware. These components handle connection and rotation transfer inside the BT-01 layout. Dogbone shafts link moving drivetrain sections, while cup joints and shaft ends sit at key handoff points between connected assemblies. Using original parts helps maintain the intended fit of the chassis design and keeps replacement work aligned with the existing BT-01 structure. The set is described as C Parts wheel axles and centre shaft, which makes its role within the chassis system clear for maintenance planning. This spare parts set fits workshop use, routine upkeep and targeted replacement after wear or damage in regular RC running. It also supports keeping a BT-01 chassis ready for the next rebuild session by covering several related drivetrain components in one pack. Compatible with the BT-01 chassis. Warning! Not suitable for children under 14 years.
Axes & drive shafts
BT-01 T Parts, RC spare parts, suspension arms
300051736€6.79
The BT-01 T Parts set is an original spare parts sprue for the BT-01 chassis, bringing together key structural pieces used around the suspension and body mounting areas. Molded in black and supplied as a single T runner, the set gives a direct source for replacing worn, damaged or missing chassis parts while keeping the fit aligned with the BT-01 platform. Alongside suspension arms, the sprue carries body mounts, bumpers and damper shafts, plus further related pieces formed as part of the same runner. The image layout shows mirrored left and right components, support posts, mounting sections and smaller braces, which helps identify each part before installation. This kind of grouped spare set is useful when several connected areas need attention at once, rather than replacing only one isolated piece. As an original spare part from Tamiya, it is intended to match the chassis design named in the data rather than serve as a universal RC car part. On the bench, the set suits routine maintenance after repeated running sessions, impact damage or a rebuild of a BT-01 chassis. It also helps keep a parts box stocked with core replacement pieces that are often needed around suspension and body support points. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
Bumper Ford Ranger Subaru Brat model spare part
319335553€19.99
This replacement bumper supports repair and upkeep on selected Tamiya vehicle builds by restoring a small but visible body detail in a single swap. The part is supplied as 1 piece and is identified in the source data for Ford Ranger and Subaru Brat applications, making it a focused choice for maintenance rather than a general universal fitting. The black moulded form shows multiple mounting points and a shaped center section that align it with model assembly hardware and body attachment areas. That layout helps when sorting spares on the bench, checking compatibility during a rebuild, or replacing a missing section after use. The source data also links the part to Sand Scorcher 58441 and 58452 references, which adds another concrete route for matching it to an existing build or parts collection. As a single replacement component, it suits targeted repairs where the rest of the vehicle remains in serviceable condition. In workshop use, a dedicated spare like this keeps restoration work moving without replacing larger assemblies. It also fits neatly into labelled parts storage for future rebuilds, especially where older Tamiya models are maintained over time and original trim details need to be brought back into place. Warning! Not suitable for children under 14 years.
Gears & motor pinions
C-Parts Gearboxguard, model spare parts for CC-01
300005521€15.79
C-Parts Gearboxguard for CC-01 supplies replacement molded components for drivetrain and chassis-area service on a compatible model build. The black sprue format keeps the individual sections together until trimming, making it easier to identify the required shapes during a repair session at the workbench. The set is presented as model spare parts rather than a complete kit, with molded guard, housing and fastening-area forms visible on the frame. Ribbed detailing, screw holes and cylindrical mounting posts support the mechanical role of the parts once fitted into the existing assembly. Several circular pieces and hexagonal cap-like forms add further replacement coverage for the same component group, which helps when an older build needs targeted maintenance instead of a full parts change. This format suits rebuilds after wear, damage or disassembly, and it also helps keep a CC-01 chassis in running condition with matching replacement sections on hand. AreBatteriesIncluded is stated as false in the data, and no battery is included with these spare parts.
Shock absorbers & springs
C.V.A II Oil-Shock-Set Super Short, damper set
300050746€26.49
The C.V.A II Oil-Shock-Set Super Short is a 48-piece damper set for assembling 2 extra short oil dampers for RC chassis applications. Its shortened format suits layouts where suspension space is tight or where a lower chassis ride height is needed without moving away from an oil-filled damper design. The set is supplied as 1 oil damper set and is intended for model use from 14 years. This version is designed for MF-01X chassis use and also matches the TT-02RR chassis, where it serves as kit standard equipment. The assembly diagrams show the working structure in detail: piston rods fit into the cylinders, O-rings and E-rings secure the moving parts, damper oil is filled into the cylinder, and the piston is moved through the oil to release trapped air before the cap is tightened. Spring installation is completed with dedicated adjuster parts, allowing the suspension unit to be built to the required kit setting. That sequence gives the set clear value for replacement, rebuild and chassis-specific tuning work. On the bench, the compact damper length helps when refreshing an existing suspension layout or preparing a chassis for a lower stance. For MF-01X rear use, 5x9 mm pillows, 19805611, are required separately. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
C.V.A.II Oil Damper Set Mini, RC shock set
300050519€36.29
The C.V.A.II Oil Damper Set Mini adds an oil-filled suspension option to compatible RC chassis and brings a more tunable setup to compact model car builds. Supplied as a 2-piece set, it is designed for builders who want to replace or refine standard dampers with an adjustable unit that can be matched to different mounting positions. Each damper can be adjusted from 55 to 70 mm, giving the set a usable range for several chassis layouts named in the compatibility list. The set is suitable for TD4, TD2, DB02, DB01, DF-03, DF-02, DT-02, DT-03, F103GT, GF-01CB, TT-02B, TT-01 TYPE-E and WR-02CB. The included damper oil supports the oil-pressure design, where the internal fluid works with the spring and shaft movement to manage compression and rebound during running. This makes the set relevant not only as a replacement part, but also as a tuning step when suspension response needs to be matched more closely to the chassis setup. On a bench build, the adjustable length helps when preparing a specific front or rear suspension position before installation. During running sessions, the oil-filled construction supports more measured chassis movement over changing surfaces and through repeated direction changes. For installation, 5 mm ball heads are required separately. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
C.V.A.II Oil Damper Set Short, RC shock set
300050520€39.49
The C.V.A.II Oil Damper Set Short brings oil-filled suspension control to a wide range of RC chassis, with 2 short dampers designed for tuning or replacement use. Its adjustable 80 to 97 mm length gives room to match the setup to different vehicle layouts, helping the suspension work with the chassis rather than against it on rough sections and changing surfaces. This set is suitable for TD4, TD2, CW-01, DB02, DB01, DF-03, DT-02 and TT-02B chassis, and the data also names Monster Beetle, Blackfoot, Lunch Box, Midnight Pumpkin, Manta Ray, Top Force, Force and Blitzer Beetle among the compatible models. That broad fit makes it useful both for restoring an older runner and for refining the handling of an active build. The oil damper format uses fluid resistance inside the shock body to smooth compression and rebound, giving a more measured suspension action than a simple friction-based setup. On the bench, the pair suits maintenance, repair and chassis-specific tuning work where damper length matters. A 5 mm ball head is required for mounting, with part 300050592 required separately, so the set can be installed with the correct attachment hardware for the chosen model. Warning! Not suitable for children under 14 years.
Axes & drive shafts
CC-01 B-Parts, steering servo saver spare set
300005520€15.79
CC-01 B-Parts brings the steering and servo saver section together in one spare parts sprue, giving compatible builds a direct route back to clean mechanical function. The black injection-molded runner presents the parts in an organized layout, with larger mirrored pieces, smaller linkage forms and circular clips arranged for clear identification at the bench. This set is intended as replacement hardware for the CC-01 rather than as a complete vehicle kit, so the focus stays on the steering assembly where accurate fit matters most. Visible molded part numbers such as 8, 9, 10, 11 and 13 help distinguish the individual shapes during preparation. The runner format keeps each component attached until needed, which supports tidier handling while checking the required section against an existing build. Glossy black molded surfaces and crisp edges reflect the technical character expected from RC maintenance parts. On a repair bench, the sprue suits worn steering sections, missing servo saver pieces or a planned refresh of an older chassis. It also fits neatly into a spares collection for hobby work, where keeping the correct CC-01 steering parts close at hand can shorten downtime between rebuild sessions.
Other spare parts & accessories
CC-01 D-Parts, body mount spare part
309005741€7.99
CC-01 D-Parts is a body mount spare part set for model maintenance on the 58324 reference. The set provides 2+2 replacement parts, making it useful when original mounting points are worn, missing or damaged and the shell needs the correct support points back in place. The designation D Parts identifies this set within the CC-01 parts structure, which helps when matching replacements to an existing build or planning a repair. As a model supply rather than a general-purpose accessory, it is intended for a specific application instead of broad compatibility across unrelated chassis types. The body mount function matters at the point where the shell is positioned and secured, so using the named replacement set helps keep that connection in line with the original layout. Batteries are not included. This spare part set fits naturally into workshop tasks such as replacing lost components during a rebuild, refreshing a used chassis, or keeping matching parts on hand for future maintenance. It also works as a practical stock addition alongside other service parts for the same CC-01 reference, especially when a repair calls for the exact D Parts designation rather than a substitute. Warning! Not suitable for children under 14 years.
Gears & motor pinions
CC-01 G-Parts, spare parts set for 58132
309005422€17.29
CC-01 G-Parts for 58132 provide a focused spare-parts set for drivetrain service, centered on molded mechanical components used in rotational power transfer. The set brings together black injection-molded gear elements and related mounting parts that suit repair work on an existing compatible model. Visible components include multiple spur gears, bevel gears, a larger gear with an integrated vertical pinion, a round plate with screw holes, and additional small parts carried on a sprue frame. That combination points to gearbox or differential-related functions where meshing teeth, axle positions and cover placement all need to match the original layout. The larger geared part with integrated pinion supports a compact transfer step within the mechanism, while the bevel gear forms indicate angled drive movement inside the assembly. The round plate adds a fitted structural piece rather than loose hardware, helping restore the intended arrangement of the surrounding mechanism. On the bench, this set suits planned maintenance, wear-related replacement, or the completion of a drivetrain rebuild when original molded parts are no longer usable. It also works well as workshop stock for model owners who keep compatible mechanical spares ready for future service on 58132-based running gear. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
CC-01 M-Parts Toyota, model spare parts, 2 pcs
309115264€26.49
CC-01 M-Parts Toyota is a spare parts set for model work on kit 58445 and provides 2 replacement parts for the matching build. The black injection-molded frame groups the components on a single sprue, so the original shapes, attachment points and part orientation stay easy to reference during repair or rebuild tasks. The molded layout shows several distinct forms, including long curved sections, mirrored arm-shaped pieces, smaller mounting blocks and round connection elements. These details matter when a damaged section needs to be replaced with a part that matches the intended geometry of the original assembly. Because the pieces remain attached to the runner before removal, each section can be identified against the build step before cutting it free. The preformed holes and connection points support clean integration with the corresponding assembly positions in the specified model. This set fits situations such as replacing lost parts during a paused build, refreshing worn sections on an existing chassis, or keeping a stored model ready for future maintenance. In a workshop drawer or alongside a current project, the sprue serves as a direct source for matching CC-01 M-Parts Toyota components tied to kit 58445. Warning! Not suitable for children under 14 years.
Axes & drive shafts
CC-01 Universal Joint, model accessory for Pajero
304135042€15.99
The CC-01 Universal Joint is a dedicated model accessory for Pajero 58132 and serves as a replacement drivetrain part where a precise rotating connection is needed. Its universal-joint design allows torque to pass between connected parts even when the angle changes, which is important on a chassis layout that moves through steering and suspension travel. Used during maintenance or repair, this component helps bring a worn drivetrain area back to a defined mechanical fit. The clear CC-01 designation keeps the application focused on the matching platform, while the Pajero 58132 reference identifies the intended model directly. That makes part selection more straightforward when servicing an existing build rather than replacing larger assemblies unnecessarily. As a single-purpose spare part, it suits bench work that focuses on keeping the drivetrain operating cleanly and consistently. In a workshop setting, the joint can be fitted during routine overhaul after extended running or when a damaged coupling starts to affect smooth rotation. It also works as a practical stock spare for model owners who maintain a CC-01 Pajero 58132 and want the correct replacement ready for the next service interval. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
CC-02 Aluminum Damper Set, chassis upgrade
300054991€94.99
The CC-02 Aluminum Damper Set equips a CC-02 chassis with 4 oil dampers built around lightweight aluminum cylinders. Their narrower shape compared with standard resin cylinders gives the suspension a more realistic scale appearance while the low-friction cylinder surface helps the dampers respond more cleanly across changing terrain. Assembly creates 4 dampers using cylinders, cylinder caps, O-ring caps, adjustable retainers and the included attachment parts. The instruction flow shows oil-filled construction with piston movement used to release trapped air before the cylinder cap is tightened, a setup that supports controlled damping rather than a simple spring-only action. Ball connectors are fitted at both ends, changing the upper mounting style used on standard CC-02 kits and allowing freer motion as the suspension works through roll. The dampers accept the chassis kit-included coil springs, and the leaflet also specifies compatibility with separately sold 12.6 x 50 mm option springs. On a trail-style CC-02 build, this set suits builders aiming for a more detailed underbody view and a more fluid suspension response over ruts, stones and side-to-side weight transfer. It also fits tuning-focused rebuilds where the damper layout is being updated without changing the chassis platform itself.
Other spare parts & accessories
CC-02 LF 6mm Ball Collar (18), chassis parts
300054945€21.19
The CC-02 LF 6mm Ball Collar set adds a focused drivetrain and suspension upgrade to CC-02 chassis cars by replacing kit-standard C9 parts with low-friction steel components. Each collar uses a plated surface to minimise resistance where moving parts pivot and slide, so link-arm action feels cleaner and more direct when the chassis works over uneven terrain. The pack includes 18 collars in total. Of these, 16 are assigned to the link arms, while 1 fits the steering linkage and 1 fits the battery plate, giving the set a chassis-specific layout rather than a generic hardware mix. The 6 mm size matches the stated fitment, and the steel construction brings a precise contact surface to the suspension hardware. In rigid suspension setups, that lower resistance helps the links move with less drag through their travel, which supports more consistent articulation across rough sections. Installed on a CC-02 build, the collars suit tuning sessions that focus on suspension response and chassis control rather than cosmetic changes. They also fit maintenance work where worn standard parts are being swapped for smoother-running hardware in the steering and link assemblies.
Axes & drive shafts
CC-02 SS Adjust Tie-Rod Set, chassis accessory
300054929€23.99
The CC-02 SS Adjust Tie-Rod Set adds a more tunable steering linkage to compatible CC-02 chassis cars by replacing the standard rigid molded link with stainless steel turnbuckle shafts. That change brings toe angle adjustment into the setup, allowing the chassis to be dialed in with greater precision for different running conditions and handling preferences. The set includes 1 x 104 mm stainless steel tie-rod, 1 x 53 mm stainless steel tie-rod, adjusters, and small attachment parts. The turnbuckle shafts feature hex adjustment sections, so length can be changed with a wrench as shown in the set documentation. This mechanism makes it possible to alter the linkage length directly through the shaft rather than removing and replacing a fixed rod. Stainless steel construction gives the main rods a durable metal format suited to repeated setup changes on the chassis. Installed in place of the standard kit linkage, the set supports fine setup work when steering response needs a more exact toe setting than the stock molded part allows. It suits bench tuning, rebuilds, and upgrade work on CC-02 based builds where adjustable linkage geometry is part of the chassis setup. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Chassis Protective Sticker, RC accessory, 0.3 mm
300054499€15.79
This hard protective film is made for the underside of an R/C vehicle chassis, where repeated contact with the track surface can leave marks during regular running. At 0.3 mm thick, it adds a thin sacrificial layer that takes the abrasion while leaving the chassis itself covered. The transparent finish keeps the visual character of the model unchanged. The sheets measure 180 x 330 mm and come in a pack of 2, providing material that can be cut to suit different chassis shapes and lengths. The highly adhesive surface is intended to bond securely under the main chassis, where constant rubbing and sliding place the greatest demand on protection. Because the film is supplied as full sheets rather than pre-cut sections, it can be adapted to a wide range of R/C vehicle layouts. This makes it useful both for a fresh application and for replacing worn film after repeated use. In workshop preparation, the film can be trimmed before a run and applied to the areas most exposed to scraping. After track sessions on abrasive surfaces, the protective layer helps keep the underside cleaner in appearance and reduces direct wear on the chassis base.
Other spare parts & accessories
Craft Tweezers, papercraft tool, 140 mm
300074080€22.49
These craft tweezers are designed for papercraft work, where small tabs, narrow folds and glued sections need controlled handling. At 140 mm in length, they offer a compact format that sits easily in the hand while keeping the tip visible during close, detailed tasks. The foremost part uses an original TAMIYA design created to improve effectiveness in gluing, paper bending and the drying process. That shape helps hold and guide thin paper parts with more control than fingertips alone, especially when working along edges, corners and tight contact points. The tweezers are made from SUS410 stainless steel and finished with a hairline surface, giving the tool a precise, clean look suited to bench work and hobby tables. The pointed, angled form also helps reach into small spaces between folded sections without covering the working area. Sticker and decal application is another practical use, particularly when small markings need careful placement before final pressure is applied. On a papercraft build, during detail finishing, or while handling delicate printed parts, these tweezers support steady, accurate movements across each step of the work. Warning! Not suitable for children under 14 years.
Axes & drive shafts
Cup Joint Universal Shaft for TT-01 DF-02
300053790€21.29
This Cup Joint Universal Shaft is a drivetrain spare part for TT-01 and DF-02 chassis setups, built to work at the gearbox in combination with an assembly cardan shaft. The pot joint design is intended to suppress drive losses, supporting smoother running when the drivetrain is under power. The set contains a left and a right part, giving the specified pair needed for the matching drivetrain layout. Its application is clearly defined for use with the DF-02 Assembly Universal Shaft 53791 or the Assembly Universal Shaft for TT-01 and TA04 53792. That makes it a focused choice for maintenance, replacement, or a driveline setup built around those universal shaft systems. The compact metal parts are shaped for precise fit within the transmission area, where clean engagement matters for consistent rotation. On the bench, this kind of component belongs in rebuilds, wear-part replacement, or a planned drivetrain update on compatible chassis. In running use, the gearbox connection and universal shaft pairing support a more fluid transfer of drive through the system, especially where a correctly matched left and right set is required. Warning! Not suitable for children under 14 years.
Axes & drive shafts
D-Parts F/R Upright, model spare part, 1 pc.
300005296€14.49
D-Parts F/R Upright is a model spare part for selected Tamiya vehicle builds and is supplied as 1 piece. The molded black component is shaped for front and rear upright use, making it a practical choice when an original part from a compatible chassis setup needs replacement during maintenance or repair. The part is specified for compatibility with 58321, 58232 and 58256. Its form combines mirrored upright sections with circular housings, angled support arms, fastening holes and molded connection points in a single unit. That layout matters during repair work because the geometry of an upright part affects how surrounding running gear components line up and mount. Replacing a worn or damaged section with the correct designated part helps restore the intended fit within the assembly area. This spare part suits workshop stock for ongoing model upkeep, rebuilds after heavy running, or the completion of an older chassis that needs the original designated component. Kept alongside other maintenance parts, it supports faster repairs when a compatible model returns to the bench for service or parts replacement.
Shock absorbers & springs
Damper Bag BF1-8, spare parts set for 58441/58452
319401427€44.99
The Damper Bag BF1-8 is a spare parts set for the Tamiya references 58441 and 58452, bringing 28 damper-related components together in one pack for targeted maintenance work. Silver tube sections, rods, caps, bushings and translucent spacer rings form a compact hardware assortment that suits repair tasks where the original suspension parts need replacement. The included contents are listed as 1 damper set with 28 pieces, making the pack a focused source for the small components that are often needed during servicing. The BF1-8 designation helps identify the correct parts group for the stated model numbers, which is useful when matching replacement hardware to an existing build. The mix of metal-look and molded parts shown for the set points to several connection and spacing functions within the damper assembly rather than a single loose replacement part. On the workbench, this set fits routine model upkeep, rebuilds after wear, or the replacement of lost small parts during disassembly. For compatible 58441 and 58452 builds, the grouped contents make it easier to restore the damper area with matching pieces kept together in one set. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
Damper Bushing, model spare part set of 8
319808279€12.29
This set provides 8 damper bushings for model maintenance and replacement work, giving matching inserts for assemblies that use this compact flanged format. Each piece is shown in black with a cylindrical body, a central hole and a lip on both sides, a shape that supports seated placement in the intended mounting point. The small format makes the set useful when a worn insert needs to be exchanged or when spare bushings are kept ready alongside other service parts. Because all 8 pieces share the same form, the pack supports consistent replacement across the same assembly area. The through-hole design suits fastening or guided pass-through where the matching model layout calls for a bushing, while the flanged edges help the part sit in place within the corresponding opening. On the workbench, this kind of spare part belongs in regular upkeep for model vehicles and related mechanical builds that use damper-mounted components. The set can be used during repair sessions, rebuilds or planned maintenance, where fresh bushings help return the intended fit of the original assembly. Warning! Not suitable for children under 14 years.
Screws & ball head screws
DB-01 3mm Thin Alum. Lock Nut, RC accessory
300054155€9.79
The DB-01 3mm Thin Alum. Lock Nut set adds a compact aluminum fastening option to compatible RC chassis, with 5 blue anodized lock nuts included in the pack. The 3 mm format suits platforms that use this hardware size, and the thin profile helps when surrounding parts leave little room for a taller nut. This set is intended for a broad list of chassis named in the data, including DB01, DB02, DN-01, F104PRO II, F104Ver.II PRO, F104W, F104, M-08 CONCEPT, TA07 MS, TA06 MS, TA06, TA06 PRO, TB-Evo.7, TC-01, TRF503, TRF502X, TRF420X, TRF420, TRF419XR, TRF419X, TRF419, TRF211XM, TRF201XMW, TRF201, TRF103, TRF102, TRF101, XV-02PRO, XV-01 Chassis, XV-01 PRO and XV-01T. Aluminum construction reduces weight compared with standard metal hardware, while the lock-nut form is made for fastening duties on running chassis. For workshop maintenance, rebuilds or detail-focused upgrades, the 5-piece set provides matching hardware for multiple mounting points on one chassis. The blue anodized finish also gives exposed fastening points a more technical appearance on race-oriented and off-road builds. Warning! Not suitable for children under 14 years.
Screws & ball head screws
DB-01 5mm Heavy Duty Adjuster, spare part, 8-pack
300051283€6.39
The DB-01 5mm Heavy Duty Adjuster set supplies 8 matching spare parts for maintenance and rebuild work on compatible model assemblies. Each adjuster is specified with a 5 mm ball end and a 25 mm length, giving a clearly defined replacement dimension when an existing linkage needs the same format again. The set is described as a heavy duty version, making it a direct choice when the required part callout is DB-01 and the 5 mm, L=25 mm specification is needed. The scope of delivery contains 8 ball head pans, which supports replacing several worn connection points at once or keeping identical parts ready for later service work. The repeated format across all 8 pieces also helps maintain a consistent setup across the same mechanical area. On the workbench, this set fits naturally into routine repair, parts sorting and planned upkeep of a DB-01 build. Matching dimensions make comparison with removed hardware straightforward, and the 8-piece quantity suits both immediate replacement and keeping reserve parts on hand for future maintenance. Warning! Not suitable for children under 14 years.
Screws & ball head screws
DB-01 5x5mm Al.Ball Connector, model accessory
300054209€18.79
The DB-01 5x5mm Al.Ball Connector set adds a precise moving joint to compatible model assemblies, combining lightweight aluminum construction with a fluorine coating for smooth, lasting action at the linkage point. Each connector uses a spherical head, narrow neck and threaded shaft layout that suits pivoting connections where clean movement and repeatable fit matter. A fixed 4 mm distance from the seat bottom to the cushion ball gives this hardware a defined geometry for suspension setup changes, opening a wider adjustment range than a standard unspecified fit. The hexagon head supports firm tool engagement during installation, which helps when tightening small hardware into a chassis or suspension mount. The set contains 5 matching connectors, making it suitable for replacing worn parts or keeping identical hardware across several connection points. The metallic finish and compact 5x5 mm format suit detailed maintenance work where small differences in fit can affect movement. On a workbench, these connectors suit rebuilds, tuning sessions and routine parts replacement on a DB-01 based setup. They also fit neatly into a spares box for trackside servicing when linkage hardware needs a quick swap to restore smooth articulation. Warning! Not suitable for children under 14 years.
Screws & ball head screws
DB-01 5x5mm Ball Connector, RC chassis part
300053906€18.29
The DB-01 5 x 5 mm aluminium ball connector adds a compact adjustment point to compatible R/C chassis and supports more precise upper arm positioning where setup changes matter. Its blue anodised finish and hex head format give the small hardware piece a clean technical look while keeping installation focused on a defined mounting point. This version reduces the length from the bearing surface to the ball joint from 5 mm to 4 mm, increasing the available adjustment range on competition-capable chassis. The connector is manufactured from high strength aluminium and uses a threaded shaft with a rounded ball head for linkage attachment. A hexagonal hole accepts a 2 mm wrench for controlled tightening, and the instruction sheet notes that spacers can be used if needed to adjust position further. Compatibility covers a broad list of platforms including DB02, F104Ver.II PRO, FF-04 EVO, M-07 CONCEPT, M-08 CONCEPT, TA07 PRO, TA08 PRO, TB-04, TB-05 PRO, TC-01, TRF419, TRF420, TT-02 TYPE-S and XV-02PRO. In workshop use, this hardware suits rebuilds, replacement of worn mounting points and setup revisions across touring, formula and rally chassis in the supported range. The pack contains 5 ball heads, allowing several connection points to be updated in one session. Warning! Not suitable for children under 14 years.
Screws & ball head screws
DB-01 5x5mm Steel Hex Head Ball Connector Set
300053968€14.99
The DB-01 5x5 mm Steel Hex Head Ball Connector set adds a precise metal connection point to RC chassis assemblies where compact hardware and clean fit matter. With 5 matching parts in the pack, it suits repair work, routine maintenance and fresh builds that need consistent ball-end mounting points in a small format. Each connector uses a threaded screw shaft below a flange and rounded ball top, a layout commonly used where a linkage, rod end or ball cup needs to pivot around a fixed point. The 5x5 mm dimensions support installation in tight spaces, while the hex head format helps with controlled fitting during assembly or replacement. High-strength steel gives these connectors the material basis for demanding off-road use, and the same parts can also be installed in on-road chassis. In workshop use, this set supports quick replacement of worn connection hardware on compatible RC models and keeps matching spare parts ready for setup changes. The pack contains 5 ball heads. With compatibility stated as any chassis, the set can serve as a useful stock hardware option across different model car platforms and parts boxes. Warning! Not suitable for children under 14 years.
Screws & ball head screws
DB-01 5x8 mm Ball Connector, RC chassis part
300053907€18.29
The DB-01 5x8 mm Al.Ball Connector set brings a compact aluminium tuning part into suspension setup work on compatible RC chassis. Each connector uses a blue anodized finish and a 5x8 mm format, creating a clean fit for linkage points where precise geometry changes matter during maintenance and track preparation. A key detail lies in the revised distance from the seat bottom to the cushion ball, reduced from 5 mm to 4 mm. That change broadens the available suspension adjustment range and opens finer setup steps than a standard layout allows. The hexagonal hole type supports secure tightening, so each connector can be installed with firm tool engagement rather than relying on a plain slot or rounded head. The set contains 5 ball heads, giving enough hardware for targeted replacement work or coordinated changes across multiple mounting points. Compatibility is stated for the TA05, TRF415MSX and TB Evolution IV chassis, making the set a focused choice for workshop stock, rebuilds and setup revisions on those platforms. During routine servicing, the compact dimensions and defined fit help keep suspension links moving through their intended range while supporting repeatable adjustment work. Warning! Not suitable for children under 14 years.
Screws & ball head screws
DB-01 Ball Head Connector, RC spare part, 5x8 mm
300053969€14.99
The DB-01 5x8 mm Ball Head Connector set adds a compact steel mounting point wherever an RC chassis needs a snap-on linkage connection. Each of the 5 connectors combines a spherical ball head, a short neck and a threaded shaft, creating a clean interface for articulated parts that need controlled movement during running and setup work. The 5x8 mm dimensions make this hardware easy to match to existing assemblies when worn connectors need replacement or a fresh build calls for uniform fittings across several mounting positions. High-strength steel gives these parts the material basis for demanding off-road racing use, where repeated movement and chassis loads act directly on small connection points. The same connector format can also be installed on on-road chassis, so one pack covers more than a single vehicle type. Scope of delivery: 5 ball heads. In workshop use, the set suits routine maintenance, rebuilds after heavy track sessions, or stocking spare hardware for race-day repairs. The compact size also makes it practical for builders who want matching connector geometry across steering links, suspension links or other articulated mounting points that use this format. Warning! Not suitable for children under 14 years.
Screws & ball head screws
DB-01 Dust Cover Ball Head Adjuster Set 20pc
300053980€5.39
The DB-01 Dust Cover Ball Head&Adjuster(20) is a general use option part made to protect the connection joints between ball connectors and adjusters in the suspension system. By covering these exposed joint areas, it helps maintain smooth suspension operation during repeated use and supports more consistent movement where the linkage needs to articulate freely. This set contains 20 dust covers and is intended for chassis maintenance, replacement work and fresh builds that use ball connector and adjuster linkages. The part focuses on the joint itself rather than the whole suspension assembly, adding protection exactly where dirt and wear can affect the connection. Its general use design makes it suitable across a broad range of compatible model chassis rather than limiting fit to a single platform. In workshop use, the covers can be fitted during routine servicing when suspension links are checked, cleaned or renewed. They also make sense as spare stock for rebuilds, tuning sessions or keeping several chassis ready for running with protected linkage points. Compatible with any chassis. Warning! Not suitable for children under 14 years.
Axes & drive shafts
DB-01 Fluorine Coated Suspension Balls, RC parts
300053709€16.79
DB-01 Fluorine Coated Suspens. Balls(8) is a suspension hardware set for RC chassis tuning and maintenance. The fluorine coating reduces friction between each suspension ball and its mount, which supports more fluid suspension movement when the chassis changes direction, settles into corners or reacts to surface input. The scope of delivery contains 8 balls for wishbone shafts, making this set suitable for replacing worn contact points with matching hardware across the suspension assembly. Compatibility reaches across several Tamiya chassis families: TA06, TA06 PRO, TA06 MS, TB-03 VDS and TA05 ver.II use these balls with 54064-54074 and 54171-54175. FF-03, FF-03 PRO, TB-03, TB-04 and TB-04 PRO use them with 54064 to 54074. M-07 CONCEPT and M-08 CONCEPT use them with 54760, while TC-01 uses them with 54760 and 54787. This suspension set suits regular workshop servicing, chassis refreshes and targeted setup work where smooth ball-to-mount movement matters. It also fits neatly into a spares box for track days or bench maintenance, with 8 matching pieces ready for the specified chassis applications. Warning! Not suitable for children under 14 years.
Gears & motor pinions
DB-01/TRF501X Pinion Gear 24/25T 48DP Set
300054218€16.79
The DB-01/TRF501X Pinion Gear 24/25T 48DP set adds a focused drivetrain tuning option to compatible RC chassis with 2 metal pinion gears in 24T and 25T sizes. The 48 pitch format and newly designed tooth profile are intended to reduce noise and friction loss, supporting a cleaner mesh and a smoother running feel during track sessions, maintenance work or ratio changes. Each gear uses 2 grub screw attachment holes, so the fastening position can be selected during installation on the motor shaft. The set also comes with 3 grub screws and an L-shaped hex key for fitting and adjustment. This makes the set useful both as a replacement for worn drivetrain parts and as a practical gearing option when refining acceleration, response or running characteristics on a supported chassis. Compatibility covers DB01-Chassis, DB02-Chassis, DN-01-Chassis, TD2-Chassis, TD4-Chassis, TRF201-Chassis, TRF201XMW-Chassis, TRF211XM-Chassis and TRF502X-Chassis. For TD2-Chassis and TD4-Chassis, use with 22031 is required. On the bench, the 24T and 25T choice allows quick comparison between 2 gearing steps while keeping the same 48DP standard across the setup. Warning! Not suitable for children under 14 years.
Gears & motor pinions
DB-01/TRF501X Spur Gear, RC spare part, 91T 48DP
300051314€6.99
The DB-01/TRF501X Spur Gear 91T 48DP is a dedicated RC spare part for compatible drivetrain setups, combining a 91-tooth count with a 48 pitch tooth profile for precise transmission matching during maintenance or repair. Built for use with the DB01 and TF503 chassis named in the data, it gives the drivetrain a clearly specified replacement component rather than a generic gear. The 91T layout determines the driven gear size within the transmission, while the 48DP format identifies the fine tooth pitch used for correct meshing with the matching pinion. That makes this gear relevant when restoring the original gearing arrangement on a compatible chassis after wear, damage or routine workshop service. As a model supply in the Models & Accessories range, it suits bench work focused on drivetrain upkeep rather than cosmetic changes. The listed designation DB-01/TRF501X also helps place the gear within specific RC platform families. In practical use, this spare part belongs in the workshop alongside other transmission service components for compatible off-road chassis builds. During maintenance sessions, it supports a straightforward parts swap that keeps the drivetrain specification aligned with the stated 91T 48DP format for continued running on the correct platform. Warning! Not suitable for children under 14 years.
Axes & drive shafts
DF-02 B-Parts Upright/Steering Arm Spare Set
300051076€14.29
DF-02 B-Parts Upright/Steering Arm is a chassis spare set for the DF-02 and TT-02B platform, built to restore key steering and wheel support points with matching replacement components. The black molded parts are arranged as 4 sprues with 20 pieces, making this set a practical choice when worn or damaged suspension and steering sections need to be renewed. The upright and steering arm shapes handle pivot and linkage mounting duties within the front end layout, while the mirrored forms support correct left and right installation. Multiple mounting holes are formed into the parts for chassis attachment and linkage connection. The set also includes 4 wheel nuts and 8 washers, adding the fastening hardware needed for the relevant assemblies. As a dedicated spare set, it suits routine maintenance, repair work after running sessions, or keeping workshop stock ready for future rebuilds. On the bench, the parts help bring a DF-02 or TT-02B chassis back into running condition with matching replacement geometry instead of mixed substitutes. For hobby maintenance, rebuild projects, or replacing damaged steering components after track use, this set keeps the fit focused on the specified chassis types. Warning! Not suitable for children under 14 years.
Axes & drive shafts
DF-02 Drive Shaft Set, RC spare part, 64 mm
300051081€13.29
This DF-02 Drive Shaft set provides a direct spare part solution for the DF-02 chassis and includes 2 drive shafts with a stated length of 64 mm. The matching pair format suits maintenance work where both sides of the drivetrain need the same part specification, keeping the assembly consistent across the axle setup. Each shaft follows a straight cylindrical form with ball-shaped ends and cross pins for connection at the mounting points. That layout is designed for mechanical transfer within the drivetrain while matching the geometry required by the DF-02 platform. The black finish and compact rod profile make the parts easy to identify during a rebuild or parts check. As replacement components rather than a general accessory, these shafts are intended for the named chassis application instead of broad multi-model use. The set fits routine workshop tasks such as replacing worn transmission links during servicing, refreshing a stored chassis before running, or keeping matching spare parts ready for a future repair. In a bench setup focused on DF-02 maintenance, the 2 included shafts cover a complete paired change with the specified 64 mm dimension. Warning! Not suitable for children under 14 years.
Axes & drive shafts
DF-02 E-Parts, spare parts set, wheel axle
309005756€9.79
The DF-02 E-Parts set provides replacement components for the wheel axle and differential joint area, giving compatible model maintenance a direct route to restoring key drivetrain connections. Black moulded parts are supplied on sprues, with the axle-related and joint-related sections grouped for clear identification before removal and fitting. This spare parts set is designated as E Parts for 58328 and is intended for focused servicing rather than broad replacement across unrelated assemblies. The visible component mix includes cylindrical axle-linked pieces, connector forms and longer structural elements that belong to the same parts tree. Keeping these pieces together on one runner helps confirm part shape and orientation during workshop preparation. The set format also suits repair benches where damaged drivetrain sections need matching replacement geometry from the original parts family. Used during maintenance, rebuilds or parts replacement after wear, the DF-02 E-Parts set supports continued running with the correct component group kept on hand. It fits naturally into a spares collection for model upkeep, especially when the axle and differential connection points need renewed parts to return a chassis to working order. Warning! Not suitable for children under 14 years.
Gears & motor pinions
DF-02 Metal Parts Bag A, model spare parts
309400152€30.49
DF-02 Metal Parts Bag A is a model spare parts set identified in the source data for 58328. The designation points to a defined replacement pack rather than a general accessory, making it a practical choice when an existing build needs the matching hardware group restored or completed. The stated metal construction gives this set a clear material identity, while the DF-02 naming keeps the part reference specific for workshop organisation. As a parts bag, it suits maintenance, repair and replacement tasks on a compatible build already in use. The source data places it in model supplies, which fits its role as a support component for an established model rather than a standalone vehicle or assembly kit. This also helps when sorting spares by platform and bag reference during bench work. On the work surface, a clearly named replacement pack saves time during upkeep because the part group is already narrowed to DF-02 Metal Parts Bag A for 58328. It works well as a stock spare for routine servicing, for completing an older build, or for replacing missing original metal components with the specified bag reference. Warning! Not suitable for children under 14 years.
Axes & drive shafts
DF-02 Universal Shaft Assembly, RC drivetrain set
300053791€56.99
The DF-02 Universal Shaft Assembly is an RC drivetrain upgrade set built to cut friction where the axle moves through the steering angle. In place of a standard dog bone drive shaft, the universal joint layout keeps power delivery more direct while the front end changes direction, which helps the chassis carry drive more cleanly through bends and technical sections. The set contains 1 ball cardan shaft set with 13 pieces and is built around 2 universal shafts. Visible components include wheel axle parts, cross joints, pins, grubscrews, AW grease and a hex wrench for assembly. The shafts are marked 70, and the document notes grease application at multiple moving contact points in the joint and cup areas. The assembly is designed to be taken apart again, which allows consumable parts to be replaced when wear appears instead of discarding the full shaft unit. Fitment is specified for DF-02, DT-02, DT-03, DT-03T and TT-02B chassis with the matching cup joints listed in the data. On a buggy set up for repeated steering input, jumps and direction changes, this drivetrain layout supports a more consistent feel at the driven axle and gives maintenance-focused builders a clear upgrade path within compatible Tamiya chassis. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
DF-03 B-Parts Damper Stay, chassis spare part
300051249€11.99
The DF-03 B-Parts Damper Stay set is a chassis spare part made for the DF-03 platform and supplies front and rear stay components in one pack. Its molded black parts follow the original mounting pattern, so repair work can focus on restoring the suspension mounting area with the correct fit for this chassis. Several hole positions are built into the stays, giving the assembly clear fastening points where dampers and related hardware attach. Ribbed reinforcement details are formed into the parts, and the set also shows a metal brace element fixed with screws and washers for added structure in the mounting section. This combination suits routine maintenance, replacement after wear, or rebuilding a used chassis with the proper B-parts section rather than mixing unmatched components. On the bench, the set supports a straightforward refresh of damaged front or rear mounting points on a DF-03 build. It also fits parts storage for racers and hobby workshops that keep chassis-specific replacements ready for service between running sessions. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
DF-03 Chassis, RC spare chassis frame
309335449€13.99
The DF-03 Chassis serves as the structural core for a compatible RC vehicle build, forming the main lower frame that carries the mechanical layout. Its black molded construction combines an elongated central body with raised side sections, giving the assembly a defined platform for attaching major modules while keeping the underside compact and purposeful. Across the frame, multiple drilled and countersunk mounting holes create fixed attachment points for screws and hardware. A large oval opening in the center is joined by shaped slots and recessed areas, which help organise the placement of installed parts and leave room for routed connections within the chassis layout. One end uses a rectangular mounting section with 4 visible countersunk holes, while the opposite end extends into a flat plate with additional drilled points for further fitment. These details make the frame more than a simple base plate: it establishes the geometry that the rest of the DF-03 build follows. Used as the lower platform in a rebuild, repair or replacement project, this chassis frame supports a clean restart when an existing vehicle needs a fresh foundation. It also suits workshop stock for keeping a compatible DF-03 machine in running condition after wear or damage to the original frame. Warning! Not suitable for children under 14 years.
Axes & drive shafts
DF-03 D-Parts Rear Upright Hub Carrier Set
300051251€9.59
The DF-03 D-Parts Rear Upright Hub Carrier set is a chassis-specific replacement set for the DF-03 platform, supplying the molded parts used in the rear upright and hub carrier area. With 1 D parts tree and 6 parts in the box, it gives the build a direct source for the designated components when maintenance, rebuild work or part replacement is due. The set is focused on one defined chassis section rather than a mixed hardware assortment, which keeps part selection clear during workshop use. The molded layout on the runner helps identify each piece before removal and fitting, especially when comparing worn parts against fresh replacements. Because the set is tied to the DF-03 chassis, it suits repairs that need the matching geometry and mounting form for that platform. The rear upright and hub carrier area plays a key role in how the corresponding rear assembly is put together, so using the intended parts helps restore the specified structure of that section. On the bench, this set fits naturally into routine servicing, rebuilds after heavy running, or a planned stock of spare chassis parts. It also works well as a replacement pack to keep alongside a DF-03 model, so the required rear section components are on hand when a damaged part needs to be exchanged. Warning! Not suitable for children under 14 years.
Gears & motor pinions
DF-03 Gear Parts Bag, RC spare parts set
309400411€39.99
The DF-03 Gear Parts Bag for 58370 focuses on one of the most important working areas in an RC drivetrain: the differential. This spare parts set brings together the core service components needed when the original assembly shows wear, so the drive system can return to clean, controlled power delivery under load. The set is presented as a dedicated bag for the DF-03 and, based on the included contents, covers the internal differential hardware rather than general chassis maintenance. Visible parts include a large metal gear with shaft, a smaller metal gear, 2 black outdrives, 2 black differential housings or cams, 4 large shim washers, additional small shims and washers, 2 metal pins, 2 groups of ball bearings, 6 white bushings or spacers, 4 coil springs, and a tube marked Ball Diff Grease. That combination supports rebuild work, replacement of worn running parts, and fine adjustment of the differential stack. On the bench, the mix of gears, bearings, shims and grease gives a clear route for servicing a used transmission assembly or refreshing a stored chassis before the next run. As a model-specific spare parts bag for 58370, it also helps keep maintenance organised when a DF-03 build needs the correct drivetrain components close at hand. Warning! Not suitable for children under 14 years.
Axes & drive shafts
DF-03Ra Assembly Universal Shaft RC Parts Set
300053792€35.49
The DF-03Ra Assembly Universal Shaft brings a serviceable drivetrain upgrade to compatible RC chassis, combining a ball cardan shaft layout with high-precision machining that reduces the stalling feel during steering and supports smoother cornering. In the workshop or at the track, the metal shaft parts, pins and couplers form a focused tuning set for driveline maintenance and response. The scope of delivery contains 1 ball cardan shaft set with 13 pieces. Visible set contents include 2 long shafts marked 39, joint hardware, pins, set screws, an L-shaped hex key and AW anti-wear grease for the moving contact points. The PTO shaft can be assembled and disassembled, which allows worn consumable parts to be exchanged instead of replacing the whole assembly. That serviceable layout helps keep the driveline working with the same intended action over repeated running sessions. Compatibility is specified for TT-02 chassis, TT-02D chassis, TT-02FT chassis, TT-01 TYPE-E chassis and TT-01D TYPE-E chassis when combined with the listed companion parts. This makes the set suited to targeted repair work, drivetrain upkeep and handling-focused tuning where steering load and cornering smoothness matter most. Warning! Not suitable for children under 14 years.
Gears & motor pinions
Diff. Gear Bag Grasshopper Hornet Spare Parts
319115010€6.49
This spare parts set is made for differential service on compatible Grasshopper and Hornet RC models. Supplied as a 6-piece gear bag, it focuses on one specific drivetrain area and gives repair or rebuild work the matching gears needed for a direct replacement task. The set belongs to the model supplies range and is intended for maintenance rather than first-time vehicle assembly. By concentrating on the differential section, it helps address wear in a part of the drivetrain that affects power transfer during running. The bag format keeps the relevant gears grouped together for workshop use, whether the job involves replacing worn parts or refreshing an older compatible chassis. Compatibility is stated for Grasshopper and Hornet, so the set can be selected for those named models without adding unrelated universal-fit claims. On the bench, this kind of replacement set fits routine upkeep, targeted repairs and parts storage for future service work. It is a focused choice for RC model maintenance where the differential needs the correct matching gear components rather than a general mixed spares assortment.
Other spare parts & accessories
DN-01 Inner Sponge Front Kit, foam insert set
300051448€6.69
DN-01 Inner Sponge Front Kit is a front foam insert set for selected buggy chassis, built to sit inside the front tyres and support their shape while the model is running. The set contains 2 grey open-cell foam rings and is specified for DT-03, DT-03T and DT-02 chassis applications. Inside the tyre, each insert fills the cavity between tyre and wheel so the front end keeps a more defined profile as loads shift through steering inputs and uneven ground. The donut-shaped foam form shown in the set is intended for front use, which matters when tuning the balance of a buggy around turn-in and directional control. Compatibility is stated with tyre references 51207 and 54284, giving a clear match point when replacing worn inserts or building a fresh wheel and tyre setup. The foam material also keeps the setup light compared with heavier internal fillers. This 2-piece set suits routine maintenance, a chassis refresh or a second wheel set prepared for another surface. On a running DT-03, DT-03T or DT-02 build, fresh front inserts can help restore a more even tyre profile after repeated use and compression. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Double-Sided Tape 20mm x 2m, black tape roll
300054693€14.79
This black double-sided tape gives R/C model work a clean, practical way to mount and protect equipment in one step. The 20 mm x 2 m format provides a continuous roll that can be trimmed to the exact length needed, whether the task calls for a short fixing point or a longer contact strip across a wider surface. Its heat-resistant construction suits model layouts where mounted components sit close to running electronics and need a dependable adhesive layer between parts and the chassis or mounting surface. The foam-style tape profile also helps create a slight buffer where equipment needs both attachment and a degree of separation from the surface below. Compared with pre-cut strips, the roll format keeps sizing flexible during bench work and repeated maintenance. It can be cut for receiver boxes, electronic modules or other onboard components where tidy placement matters. One roll is included.
Axes & drive shafts
Drive Shaft, RC spare part, steel, 45 mm
309805551€12.99
This RC spare part supplies 2 steel drive shafts at 45 mm length for model vehicle drivetrains that use ball differential drives. The shaft format matches Manta Ray and Fire Dragon applications named in the data, giving a direct way to replace worn drivetrain links while keeping the intended mechanical layout in place. Each shaft uses a long steel rod with formed ends that sit into the drivetrain connection points, where rotation is passed through the linked assemblies. The 45 mm measurement matters in this role because shaft length determines how the connected parts line up during running. With 2 identical pieces in the pack, both sides can be fitted with the same specification instead of mixing different lengths or constructions. The part is listed for bowling and ball differential drives, so the stated drivetrain type stays clear when selecting the replacement. This kind of spare part suits repair work, routine maintenance and the refresh of an older chassis that needs the original shaft format restored. It can also be paired with the matching ball cardan shafts named in the data when a compatible drivetrain setup is being completed with related components.
The best selection of RC spare parts
Whether you're looking to upgrade your RC model or repair it after an action-packed run – in our RC spare parts category, you'll find everything you need. Tamiya offers a wide range of high-quality spare parts for your RC models. Our spares cover all essential components to ensure your model is always in top shape.
Spare parts for RC cars: variety for every model
Our RC spare parts are specifically designed to enhance the performance and lifespan of your model. The range includes everything from steering knuckles, drive shafts, and control arms to ball joints and leaf springs. With over 400 different items, we offer everything a hobbyist could wish for. Whether you're searching for spare parts for RC cars or specific components like axle housings or oil dampers – you’ll find it here.
Why RC spare parts are important
No RC model can run without the right spare parts. RC spare parts not only ensure that your model is always ready for action but also boost performance and improve durability. Whether you need spare parts for RC cars or specific components like axles and gearbox protectors – regular maintenance and the replacement of worn-out parts are key to an optimal driving experience. With the right RC car spare parts, you can ensure that your model stays in top condition, allowing you to enjoy the full driving experience.
The benefits of Tamiya RC spare parts
When you choose Tamiya RC spare parts, you're opting for quality and precision. Each of our spare parts is perfectly matched to our models and offers the highest reliability. Thanks to high-quality materials and precise manufacturing, you can be sure that your model building project will always deliver the best performance. Whether you're just starting out in RC model building or you're an experienced hobbyist – Tamiya RC spare parts guarantee quality you can feel.
Browse through our RC spare parts shop
Explore our extensive range of RC spare parts and get your model back in top form. In our RC spare parts shop, you'll find everything you need to maintain, repair, or improve your vehicle. From beginners to professionals – we have the right RC car spare parts to take your model building to the next level.