RC tuning parts
Higher, faster, further with Tamiya tuning parts. Tune your RC vehicles just the way you want them. If you would like to find out more, you can read more here.
RC tuning parts
0.4 Module Pinion Gear Set, RC accessory, 28/29T
300053262€18.99
This 0.4 module steel pinion gear set brings precise gearing changes to compatible RC chassis, with 28T and 29T pinions that allow a finer adjustment of the transmission ratio than broader tooth-count steps. The steel construction and compact geared form suit drivetrain setups where efficient transfer of motor output matters on the track. The set is supplied as 6 parts: 2 pinion gears, 3 set screws and 1 hex key for installation. The pinions are intended for use with separately available 0.4 module spur gears, and the data names specific pairings for several chassis families. FF-03 and FF-03 PRO use it with 54227, TB-03, TB-04 and TB-04 PRO use it with 54055, TA05 Ver.II uses it with 53857, and F104 or F104W use it with 54166 plus 53104 or 53900. F104PRO II uses it with 54166. Compatible chassis named in the data include F104PRO II, F104 Ver.II PRO, F104W, F104, FF-03, FF-03 PRO, TA05 Ver.II, TB-04, TB-04 PRO, TB-03, TRF103, TRF102 and TRF101. In workshop use, the two tooth-count options support quick ratio changes between runs, while the included hex key helps with fitting and adjustment at the bench or trackside. Warning! Not suitable for children under 14 years.
RC tuning parts
04 Spur Gear 93T/104T, RC gear set, 0.4 module
300053900€9.79
The 04 Spur Gear 93T/104T set is a drivetrain tuning part for RC chassis that use 0.4 module gearing. With 93T and 104T spur gears in one pack, it supports finer ratio selection than the standard 0.6 module gear and opens up smaller adjustment steps when acceleration and running efficiency need closer control. Each gear uses a fine tooth profile that changes how the spur and pinion mesh, making this set useful when a standard ratio jump is too broad for the setup. Molybdenum in the gear material is specified to reduce friction resistance at the contact point, which supports smoother power transfer through the drivetrain. The set is intended for F103 and C Car chassis and is used together with 0.4 pinion gear #53101. That compatibility matters when preparing a chassis for different track layouts, motor characteristics or rolling conditions where a small gearing change can alter response. On a bench setup, the 2 tooth counts make back-to-back comparison straightforward because the gearing can be changed with a direct spur swap. On the track, that means a setup can be tuned toward sharper pull out of slower sections or toward a more efficient running balance across a full session.
RC tuning parts
1:10 Touring Car Short Springs II, RC spring set
300054797€19.99
The 1:10 Touring Car Short Springs II set brings finer suspension tuning to touring car setups by adding 3 short spring rates that sit alongside the existing range. Each pack contains 6 black coil springs arranged as 3 pairs, giving a direct way to alter chassis response for changing track conditions and different driving inputs. The set includes 2 Super Hard springs with white marks, 2 Medium-Hard springs with gold marks and 2 Medium-Soft springs without a color mark. That spread broadens the choices beyond the Hard, Medium and Soft options in Item 42168, making it easier to narrow in on a more exact setup. The color coding helps keep spring pairs sorted during rebuilds, test sessions and repeated suspension changes. As short springs, they are intended for touring car short damper layouts rather than standard-length units. Compatibility covers touring car short dampers in Items 50519, 50746, 53155, 53280, 53571, 53901, 54000, 54753, 42102, 42273, 42287, 42291 and 47342. On a practice day or between race heats, swapping one pair for another gives a clear mechanical route to adjusting handling balance through the suspension rather than changing the whole chassis setup. Warning! Not suitable for children under 14 years.
RC tuning parts
33T Steel Idler Gear, chassis spare part
300022087€9.49
This 33T steel idler gear is a dedicated spare part for selected RC chassis and brings a precise transmission component into repair and maintenance work. Supplied as 1 piece, it is intended for use with the BB-01, TD2, TD4 and XV-01 chassis, where the stated 33-tooth specification matches the required internal gear position. The part is used in place of MA27, identified in the source data as the green gear in the reference image. That direct replacement note matters during servicing, because it points to the exact gear position rather than leaving fitment to guesswork. The steel construction suits a mechanical role inside the drivetrain, while the compact gear form with central hub and slot reflects its function as a transmission component rather than an external accessory. For chassis owners keeping a running model in service, a clearly specified spare like this helps restore the intended internal setup with the named tooth count and platform compatibility. It fits naturally into workshop tasks such as replacing a worn transmission gear during a rebuild, refreshing a used chassis, or keeping a matching spare on hand for BB-01, TD2, TD4 or XV-01 maintenance. The single-piece format keeps the scope clear when one exact idler gear is needed. Warning! Not suitable for children under 14 years.
RC tuning parts
3x23mm Turnbuckle Shaft, RC spare part, blue
300054248€8.79
These 3x23 mm turnbuckle shafts are built for RC chassis tuning where precise linkage adjustment matters. The central turnbuckle section changes shaft length without removing the adjusters, which helps keep setup work direct when steering or suspension geometry needs a measured correction. The blue anodized finish gives the aluminum parts a clean technical look that stands out clearly in a parts tray or on the workbench. The set contains 2 threaded rods and is intended for a wide range of compatible chassis: M-06, M-06 PRO, TA06 MS, TA06, TA06 PRO, TA05, TB-Evo.7, TB-05 PRO, TT-02 TYPE-SR, TT-02 TYPE-S, XV-02PRO, XV-01, XV-01 PRO and XV-01T. Aluminum construction keeps the parts light while providing the rigid threaded form needed for repeatable adjustment. The 3x23 mm size makes this pair a specific fitment choice rather than a generic linkage part, which is useful when maintaining an existing build or preparing a chassis for a setup change. On a bench build, these shafts suit routine replacement, geometry correction or tuning updates between running sessions. The visible center section supports tool access for small length changes, making them practical spares for regular chassis maintenance.
RC tuning parts
4x18mm Titanium Turnbuckle Shafts, RC chassis part
300022086€11.99
These 4x18mm titanium turnbuckle shafts are a dedicated chassis option part for the TA08R family and related Tamiya platforms. The titanium construction pairs low weight with a crisp machined finish, while the threaded design allows the shafts to serve as key linkage hardware in compatible RC chassis assemblies. The set contains 2 shafts and is specified for use with the TA08 PRO, TA08R and TB Evo.8 chassis. Each shaft uses a double-threaded layout with a narrow centre section, a format commonly used where steering or suspension links need compact, accurately made connection points. As an option part, this pack suits routine maintenance, targeted replacement of worn hardware, or a planned chassis refresh using the exact stated size of 4x18mm. For a complete kit application, 4 shafts are required. In workshop use, the clearly defined compatibility helps when matching parts to an existing TA08 PRO, TA08R or TB Evo.8 build. The 2-piece pack also supports staged servicing, whether replacing individual linkage points or combining multiple packs to equip a full chassis with the required shaft count. Warning! Not suitable for children under 14 years.
RC tuning parts
5mm Alum. Ball Nut, RC spare part, blue, 10 pcs
300053640€14.29
This spare parts set supplies 10 aluminium ball nuts in a 5 mm format for RC model maintenance, with a blue anodized finish that gives compatible assemblies a clean, uniform look. Each piece combines a rounded ball head with a hexagonal base, a shape that supports attachment to matching sockets and linked mechanical parts where smooth, accurate movement matters. The set is intended for replacing worn ball connector nuts before play in the linkage becomes imprecise. Fresh hardware helps compatible steering and suspension connections seat correctly and move with less unwanted slack, which supports consistent running performance during regular use. The included quantity of 10 pieces suits full maintenance sessions, partial rebuilds or keeping matching replacements ready in a workshop parts box. Scope of delivery: 10 ball nuts. These aluminium ball nuts fit naturally into routine service work on RC models that use this connector style, whether a single linkage needs attention or several mounting points are being refreshed together. They cannot be used on DT-02 chassis XB models. Warning! Not suitable for children under 14 years.
RC tuning parts
5mm L.Friction Adjuster, RC spare part, 8 pieces
300053601€6.79
The 5 mm L.Friction Adjuster set brings a focused upgrade to linkage movement on compatible RC models. Made from a low-friction material, these ball connectors help linkage rods move smoothly at the connection point, which suits steering tie-rods and camber links that rely on clean, consistent articulation. Each pack contains 8 adjusters and is intended for many Tamiya vehicles that use a 3 mm turnbuckle. The 5 mm connector size makes this set a practical choice when worn rod ends need replacement across several mounting points in the same setup. The parts are supplied as adjustment pieces for model maintenance and tuning, with the connector shape built around ball-joint style linkage use. Compared with the standard material, this low-friction version lasts longer before replacement is needed. The set fits naturally into workshop tasks such as refreshing steering linkages, rebuilding camber link connections, or keeping spare rod-end parts ready between running sessions. DT-02 chassis compatibility is stated, while XB model use is not possible. Warning! Not suitable for children under 14 years.
RC tuning parts
5mm Suspension Balls, RC spare parts, low friction
300054747€9.29
These 5mm suspension balls bring a focused drivetrain and chassis tuning detail to compatible RC vehicles by reducing friction where the suspension pivots. Made from POM resin and supplied as a set of 8, they suit Tamiya vehicles that utilize 5mm suspension balls and give a straightforward way to refresh worn hardware or standardize a setup across multiple corners of the chassis. The design was originally used on the TRF419X chassis, which places these parts in proven competition-oriented running gear rather than generic workshop stock. At each mounting point, the low-friction surface helps the suspension move with less resistance as arms and linkages cycle through travel. That smoother motion can help the suspension react more cleanly to steering input, surface changes and load transfer, especially when a setup depends on free, consistent movement at small contact points. In workshop use, this set fits naturally into routine rebuilds, race preparation and parts replacement on compatible models. The 5mm size keeps selection simple for chassis built around that specification, while the pack of 8 provides enough pieces for a complete refresh of key suspension connection points on many layouts.
RC tuning parts
630 Ball Bearings, chassis tuning parts, set of 8
300054925€15.49
This set of 630 ball bearings adds a direct mechanical upgrade to compatible chassis by replacing plain rotating contact points in the reduction gears with metal bearings designed for smoother running. With 8 bearings in the pack, the set suits targeted maintenance work or the first stage of a driveline tune-up on G6-01TR and GF-01TR models. The main effect comes from lower friction at moving points inside the reduction gear assemblies. That reduction in drag helps the drivetrain transfer motion more efficiently and can lessen wear on surrounding rotating parts over time. The bearings have a compact round format with a polished metal finish, matching the small-scale hardware used in RC chassis assemblies. Each reduction gear requires 2 of these 630 bearings, so quantity planning is straightforward when preparing a larger rebuild. A full GF-01 setup needs 16 bearings in total, while a full G6-01 setup needs 24. In workshop use, the set fits neatly into routine servicing, parts replacement, or a gradual chassis upgrade path. It can be used to refresh a model that has seen regular running or to prepare compatible reduction gears before the next driving session.
RC tuning parts
Alu Wheel Hub Clamp Type 9mm, RC car hub set
300054610€16.79
This clamp type wheel hub set adds a precise 9 mm setup option for compatible RC cars that use hex hubs to secure the wheel on the axle. Each aluminum hub clamps directly onto the wheel axle, a fastening method that increases holding strength while supporting smoother wheel rotation during running and tuning work. The set contains 2 wheel hubs, a 1.5 mm hex wrench, cap screws and 2 x 10 mm shafts for attachment. The machined aluminum parts keep weight low while giving the hub area a crisp, technical fit. At 9 mm thickness, this version expands the range beyond 4 mm, 5 mm and 6 mm hub options, which makes it useful when adjusting track width and wheel position on suitable chassis. The instruction data also notes that fit depends on wheel width and offset, and wheels may contact the bodyshell on some combinations. Compatibility covers TT-01 and TT-02 chassis with longer wheel axles and wide rear tread, plus GF-01 and WR-02G chassis cars. In a workshop setup, the clamp design, included hardware and exact 9 mm thickness make this set a practical choice for replacing wide type wheel hubs or refining the stance of an existing RC car build.
RC tuning parts
Alu. Motor Guard GF-01/WR-02, RC motor cover
300054817€38.99
The Alu. Motor Guard GF-01/WR-02 adds a compact aluminum shield around the motor area on compatible Tamiya chassis, combining physical protection with airflow-focused shaping. Slotted openings across the guard help dissipate heat while the cover reduces direct exposure to dust and debris during running. The set contains 1 aluminum motor guard, 2 cap screws in 3x28 mm size and a hex wrench for attachment. Its cylindrical clamp-style form wraps closely around the motor, while the front flange uses multiple mounting holes to secure the part in position. The aluminum construction gives this accessory a precise machined look that suits detailed RC builds and upgrade-focused maintenance. Compatibility is stated for GF-01, G6-01 and WR-02 chassis cars, making it a targeted fit for those platforms rather than a universal add-on. On dirt sections, mixed surfaces or general outdoor running, the guard adds a useful barrier where loose debris can gather around the motor can. It also suits workshop refreshes and chassis upgrades where a cleaner motor area and a more finished mechanical layout are part of the goal.
RC tuning parts
Alum. Adjustable SepSusMt (A), RC chassis mount
300054884€25.99
Alum. Adjustable SepSusMt (A) brings bushing-based suspension tuning to compatible RC chassis cars with a compact aluminum mount set that replaces the standard suspension mount. The two separate mounts, A-a and A-b, work with offset bushings to alter suspension shaft position, opening detailed setup changes that can be felt in how the chassis is balanced for different track conditions. The set contains 1 Aluminum Adjustable Suspension Mount (A-a), 1 Aluminum Adjustable Suspension Mount (A-b) and 1 bushing sprue. The bushing sprue provides 7 pairs of bushing types, and each type uses a different hole position for the suspension shafts. Rotating and pairing those bushings creates 25 potential shaft offset positions, which allows fine adjustment of toe angle, tread, roll center and skid angle. The mount itself allows settings between XA and C, while the final toe angle depends on the separate suspension mounts and bushings used. Shims can be used to adjust clearance where needed. The blue anodized finish gives the aluminum parts the familiar Tamiya look on the chassis. Compatibility is stated for TRF419, TA07 and TB-05 chassis cars, making this set a focused upgrade for racers refining suspension geometry with measured, repeatable changes.
RC tuning parts
Alum. Ball Connector blue 5mm, RC spare part
300053642€13.79
These 5 mm aluminum ball connectors are a focused upgrade and replacement part for the DT-02 chassis, combining low weight, durable metal construction and a blue anodized finish in a compact hardware set. Each connector uses a threaded shaft, a hexagonal base section and a spherical head, creating a secure mounting point that still allows the linked component to articulate smoothly during running. The set contains 10 ball heads, making it useful for servicing several connection points in one session or keeping matching spares ready for later maintenance. The anodized blue finish gives the hardware a crisp technical look while also making the parts easy to distinguish during a rebuild. Replacing worn connectors in time helps maintain clean linkage action where play or wear can reduce consistency. These parts are not available for XB model use. On a workbench, the connectors suit routine chassis upkeep, targeted repairs and detail-focused tuning on a compatible DT-02 build. Once fitted, the smooth ball shape supports free movement at the joint, which matters wherever linked parts need to pivot through repeated steering or suspension travel. Warning! Not suitable for children under 14 years.
RC tuning parts
Alum. HT Servo Saver Cap, RC spare part, aluminum
300054863€5.59
The Alum. HT Servo Saver Cap is a compact RC spare part that combines a machined aluminum build with a precise fit for hi-torque servo savers. Used in place of the Q4 part, it creates a durable contact point at the saver and brings a crisp blue anodized finish to the steering area, where small hardware details remain visible during maintenance and setup. Its disc-shaped form with a countersunk center is made to seat the fixing screw neatly while keeping the cap aligned in the assembly. The aluminum construction adds a lightweight metal component to a high-load area, and the laser-engraved TAMIYA name gives the surface a clean workshop look without changing the part's function. Supplied as 1 cap, it is suited to replacing a worn original part or refreshing a compatible saver with the same specified shape and role. On an RC chassis, this cap fits naturally into routine steering service, rebuild work or detail-focused tuning. It is especially useful when a hi-torque servo saver is already apart for inspection and the Q4 position needs a fresh, more durable replacement component.
RC tuning parts
Alum. Turnbuckle Shaft 3x18mm, RC spare part
300054247€8.79
The Alum. Turnbuckle Shaft 3x18mm in blue is a compact RC spare part for chassis setups that call for precise linkage adjustment. Made from lightweight aluminum, each shaft combines threaded ends with a central section that supports clean, controlled length changes while the part remains installed, which helps keep setup work focused and efficient at the bench. The 3 x 18 mm format suits a wide range of compatible Tamiya chassis, including M-08 CONCEPT, M-06, M-06 PRO, MF-01X, TA08 PRO, TA07 MSX, TA07 MS, TA07 PRO, TB-Evo.6 MS, TB-Evo.6, TRF420X, TRF420, TRF419XR, TRF419X, TRF419 and TT-01D TYPE-E. A blue anodized finish gives the aluminum surface a crisp technical look and makes the parts easy to spot during maintenance. The stopper uses a slot that is tightened with a cap screw to lock the shaft securely. This layout also supports subtle position adjustment when a carbon shaft is used, while avoiding shaft damage and reducing the need to install or remove bearings during service. With 2 threaded rods in the set, the pair fits neatly into regular repair, replacement and tuning work on compatible RC chassis. Setup sessions, trackside checks and workshop maintenance all benefit from hardware that can be adjusted directly and returned to the car with minimal interruption. Warning! Not suitable for children under 14 years.
RC tuning parts
Alum. Turnbuckle Shaft 3x42mm, chassis part
300054250€9.39
These 3 x 42 mm aluminum turnbuckle shafts add a clean, mechanical adjustment point to compatible RC chassis, with a blue anodized finish that stands out clearly during bench work and maintenance. The threaded ends and central wrench section support direct length changes on the installed linkage, so setup corrections can be made without removing the adjusters first. The pair is intended for chassis including TA07 PRO, TA06, TA06 PRO, TA06 MS, TB-04, TB-04 PRO, FF-04 EVO, TRF419, TRF419X, TB Evo.6, TB Evo.6 MS, XV-01 PRO and XV-01T. Aluminum construction keeps the parts light while providing a precise metal interface for linkage duties. The turnbuckle format is especially useful where camber, toe or related linkage geometry needs measured adjustment through small rotational changes at the shaft body rather than full disassembly. With 2 threaded rods in the set, the parts suit paired replacement on one linkage point or a focused tuning update on an existing chassis build. The metallic blue surface also makes the shafts easy to identify among other hardware during servicing, rebuilds and trackside setup checks. Warning! Not suitable for children under 14 years.
RC tuning parts
Aluminum Adjustable Servo Horn for RC Steering
300054893€43.99
This aluminum adjustable servo horn adds fine steering setup control to compatible RC chassis by allowing the distance between the servo horn center and ball connector to be set in 1 mm increments from 15 to 22 mm. That mechanical adjustment changes the linkage geometry directly, making it possible to tune steering throw with a part that sits at the heart of the steering system. The horn also allows steering range adjustment, which helps match the setup to different chassis layouts in the compatible CC-01, GF-01, G6-01, M-05, M-06, M-07 Concept, M-08 Concept, TA07 PRO, TB-05 PRO, TT-02 and TT-02B families. Its aluminum construction brings a precise, machined feel to a component that handles repeated steering inputs. A built-in servo saver function adds impact management at the horn itself, so shocks from crashes are not transferred straight into the servo mechanism. On a touring, rally or off-road chassis, this part supports careful steering tuning through measurable linkage changes rather than guesswork. It suits rebuilds, maintenance work and setup changes where steering response and protection both matter in the same installation.
RC tuning parts
Aluminum Servo Horn, RC steering arm for TAMIYA/FUTABA
300042248€15.99
This aluminum servo horn brings a direct steering link to compatible RC chassis and replaces servo saver action with a firmer connection at the servo output. The result is a sharper steering response that suits precise setup work on track-focused models, while the blue alumite finish and machined cut surfaces give the part a clean technical look. The arm uses a raised pillow ball mounting point set 1.5 mm higher to reduce linkage interference and maintain steering angle through the linkage movement. A clamp-style serration section adds extra holding force at the spline, and tightening the 2 x 5 mm cap screw secures the horn more firmly than a screw-only layout. Scope of delivery: 1x servo arm. The part is specified for TAMIYA/FUTABA fitment and is listed for TA07 MSX, TA07 MS, TA06 MS, TB-Evo.7, TB-Evo.6 MS, TB-Evo.6, TRF420X, TRF420, TRF419XR, TRF419X and TRF419. On a competition chassis, small steering changes are easy to feel, and this direct horn is built for that kind of exact linkage setup. It suits rebuilds, tuning changes and replacement work where secure spline clamping and clean pillow ball positioning matter to the steering system. Warning! Not suitable for children under 14 years.
RC tuning parts
Aluminum Turnbuckle Shaft Set, RC Chassis Spare
300054249€8.79
This spare part set brings adjustable linkage tuning to a wide range of RC chassis with 2 aluminum turnbuckle shafts in a blue anodized finish. Each shaft uses a central hex section that allows length changes while the adjusters stay in place, making setup work on steering or suspension linkages more direct and controlled. The shafts measure 3 x 42 mm and are intended to replace the standard A12 parts in compatible kits. Supported chassis listed in the data include TT-02 Type-S, TA07 PRO, TA06, TA06 PRO, TA06 MS, TB-04, TB-04 PRO, FF-04 EVO, TRF419, TRF419X, TB Evo.7, TB Evo.6, TB Evo.6 MS, MF-01X and RM-01. For TC-01 chassis, use with adjusters such as 54869 is specified. The aluminum construction adds a metal component where repeated setup changes call for a precise threaded part with a clear wrenching point at the center. On a bench build, these shafts suit geometry changes that need repeated fine adjustment between runs. In maintenance or upgrade work, the 2-piece set provides direct replacement parts for worn or standard kit linkages on the named chassis families. Warning! Not suitable for children under 14 years.
RC tuning parts
Ball Bearing Set 1150, RC car accessory, 16 pcs
300054579€30.99
The Ball Bearing Set 1150 brings a focused drivetrain upgrade to compatible R/C car chassis by replacing plastic bushings with 16 metal bearings sized at 11 x 5 x 4 mm. Each bearing supports smoother rotation at key moving points, helping the transmission run with less drag during acceleration and steady laps. This set is intended for a straightforward tuning change that targets friction where axles and drivetrain parts turn under load. In compatible entry level platforms, the swap can help reduce power loss through the driveline while also supporting the longevity of axle joints. The pack provides enough bearings for several listed chassis layouts: DT-03 and DT-02 require 14 bearings, while WR-02, WR-02G and WT-01 require 16. That fitment detail makes the set useful both for a complete replacement on some chassis and for a near-complete conversion on others. On the bench, the compact 1150 format suits builders refining a buggy or wheelie platform with a practical mechanical upgrade rather than a cosmetic change. It fits naturally into maintenance work, rebuilds and fresh kit preparation where smoother rolling parts and more efficient drivetrain movement matter most.
RC tuning parts
BB-01 Alum. Servo Stays, chassis accessory
300022070€23.99
These BB-01 Alum. Servo Stays bring a metal mounting upgrade to the BB-01 chassis with 2 silver-anodized aluminium parts shaped for the servo stay position. The machined L-form, stepped inner corner and mixed drilled and threaded holes give each stay a defined structural role inside the chassis layout. The set contains 2 stays, allowing the left and right mounting points to match in material and finish. The silver anodized surface gives the aluminium a clean technical look, while the threaded holes support direct fastening at the intended fixing points. The larger plain holes and the vertical leg geometry indicate a part designed to hold position accurately once installed. As a chassis accessory rather than a general hardware piece, this set is focused on the BB-01 platform named in the data. That makes the pair a useful choice when refreshing a used chassis, replacing the standard servo stays, or adding a more detailed metal element during a new BB-01 build. On the bench, the 2 matching parts bring a neat, uniform appearance to the servo mounting area and keep the upgrade closely tied to the specified chassis system.
RC tuning parts
BB-01 Aluminium Damper Stays Rear Accessory
300022089€26.99
The BB-01 Aluminium Damper Stays Rear accessory adds a metal mounting set to the rear section of a BB-01 chassis build. Its layout is intended for installation under the roll cage roof, where the rear aluminum damper mount bar works with the included adapters and stiffener post to create the specified attachment point. The silver-anodized finish gives the visible parts a clean technical look that matches detailed off-road model assemblies. Included in the set are 1 rear aluminum damper mount bar, 1 stiffener post, 2 damper mount adapters and 2 3x30 mm hex head screws. The two adapters use a double-hole form, while the long central bar and the post create a compact hardware group for the rear damper mounting area. This makes the set useful for BB-01 owners looking for the exact parts named for this chassis rather than a generic hardware mix. In a workshop setup, the parts suit maintenance, replacement or a focused chassis update where the rear mounting section needs the specified metal components. The compact contents also make the set easy to keep with other BB-01 spares for later fitting or rebuild work. Warning! Not suitable for children under 14 years.
RC tuning parts
BB-01 Aluminium Steering Arms L/R, chassis upgrade
300022090€28.99
The BB-01 Aluminium Steering Arms L/R bring a focused steering upgrade to the BB-01 chassis with silver-anodized aluminum parts shaped for the left and right sides. Replacing the standard S2 and S3 parts, these arms add rigidity at a key point in the steering linkage, helping inputs travel through the assembly with a more linear response. Each set contains 1 left arm and 1 right arm, so the steering assembly can be updated as a matched pair rather than mixing materials across the same mechanism. The arm shape uses a larger recessed mounting end and a smaller drilled connection point, with reinforced contours around the structure to support accurate pivoting movement inside the front steering layout. This makes the set especially relevant for builders refining steering feel on a BB-01 based machine rather than changing unrelated chassis areas. The parts are intended for use in place of the original S2 and S3 components on compatible builds. Use with Item 22091 is recommended. Ball bearings are required separately. On the bench, this upgrade suits rebuilds, maintenance work, or a fresh BB-01 assembly where the steering system is being specified with metal linkage parts from the start. Warning! Not suitable for children under 14 years.
RC tuning parts
BB-01 Aluminum Damper Stays Front RC Hop-Up
300022088€44.99
These BB-01 Aluminum Damper Stays Front parts add a focused chassis upgrade to the front damper mounting area. The set uses 2 silver-anodized aluminum stays in place of the standard A27 parts, bringing a metal component to a section that handles the damper attachment points on the BB-01 layout. Alongside the 2 stays, the set provides 2 P3 O-rings, 2 P4 O-rings, 4 countersunk 3x12 mm hex head screws, 2 standard 3x12 mm hex head screws, 2 5 mm ball posts and 4 aluminum spacers measuring 3.1 x 4.4 x 1.0 mm. The countersunk holes in the stays work with the included flush screws for a neat fit. The paired O-rings and spacers support the specified mounting arrangement, while the ball posts add the required connection points for the front setup. This accessory suits builders refining a BB-01 buggy with dedicated chassis parts rather than universal hardware. During assembly or maintenance, the silver finish stands out clearly against surrounding components, making the upgraded front section easy to identify on the bench and on the completed model. Warning! Not suitable for children under 14 years.
RC tuning parts
BB-01 Aluminum Front Uprights, chassis parts
300022069€53.49
These silver-anodized aluminum front uprights are made for the BB-01 chassis and supply a matched 2-piece set for the front suspension area. The identical right and left shape keeps both sides visually consistent and streamlines parts selection when the chassis is being serviced or updated. Each upright features a large central opening for the hub area plus smaller mounting points for the surrounding front-end hardware. That layout supports accurate positioning within the chassis assembly and gives the front corner a clean, precisely machined metal component in place of the standard part. The silver anodized finish adds a crisp technical look that stands out clearly during a build or maintenance session. As a dedicated BB-01 chassis part, this set suits replacement after wear, a rebuild of the front end, or a selective aluminum conversion focused on the upright area. The 2 included pieces cover both front sides, making the pair a straightforward choice when matching geometry and finish across the chassis matters.
RC tuning parts
BB-01 Aluminum Steering Bridge, chassis part
300022091€14.79
The BB-01 Aluminum Steering Bridge is a dedicated chassis part for the BB-01 platform, built to replace the standard S1 part with a silver-anodized aluminum component. Its rigid construction strengthens the steering linkage area, supporting a more direct steering feel and a more even response as the front end changes direction. The part comes as 1 piece and is shaped for the BB-01 chassis layout, so it serves as a focused hardware upgrade rather than a general universal fitting. The silver-anodized finish gives the machined aluminum surface a clean technical look while matching the functional role of a precision steering component. The bridge uses the existing mounting position in place of the S1 part, concentrating the upgrade on the connection point that guides steering movement. Use with Item 22090 is recommended. Ball bearings are sold separately. In a workshop build or a running chassis refresh, this steering bridge suits BB-01 owners who want to refine the front steering assembly with a specific metal replacement part. It also fits well into a step-by-step tuning plan where individual steering components are upgraded one area at a time. Warning! Not suitable for children under 14 years.
RC tuning parts
BB-01 Slipper Clutch Set, chassis spare part
300022071€57.49
The BB-01 Slipper Clutch Set adds an adjustable drivetrain element to the BB-01 chassis, centering on a gear-integrated shaft with 20T layout and a spring-loaded clutch assembly. By changing spring tension, the clutch alters slip timing and acceleration traction, which can help the chassis deliver steadier power when grip changes across the surface. The set contains the slipper clutch for BB-01 Chassis and is supplied with the core assembly parts: 1 gear-integrated shaft, 1 slipper screw, Plate A, Plate B, 2 slipper pads, 1 1050 ball bearing, 2 spring seats, 1 spring and 1 2.6 mm lock nut. The friction-based clutch action lets the drivetrain absorb part of the initial load under acceleration instead of locking the drive instantly, giving more scope to tune how the BB-01 responds as power comes in. The included spare part 86T gear extends service support for the same chassis platform. This set suits rebuilds, routine maintenance and setup changes on BB-01 running cars. It can be fitted when refreshing worn drivetrain parts or when a different clutch response is needed for changing track grip, repeated acceleration runs or general chassis tuning.
RC tuning parts
C.V.A.II Damper Collar, RC spare part set
300050950€7.69
The C.V.A.II Damper Collar set is a dedicated RC spare part for suspension maintenance on selected Tamiya platforms. Supplied as 1 sprue with 22 parts, it concentrates on the damper area and gives compatible chassis a defined source for replacement and setup work. Fitment is stated for DT-02 chassis, DT-03 chassis and DT-03T chassis, with additional use on vehicles equipped with 54567. For DN-01 chassis, the data also names an important restriction: 54028 cannot be used together. That combination note matters during parts planning because it keeps the suspension configuration aligned with the listed specification rather than trial fitting unrelated pieces. The set is not available for XB models, which separates it clearly from those versions. On the bench, this spare part set suits routine damper service, rebuilds after wear, or preparation of a compatible chassis before the next run. The 22-part sprue format keeps the included pieces together in one pack, making it easier to sort the required parts for maintenance on the supported DT and DN platforms. Warning! Not suitable for children under 14 years.
RC tuning parts
Carbon Short Damper Stay Set, RC chassis upgrade
300022076€48.99
This Carbon Short Damper Stay Set brings front and rear carbon fiber damper stays into one focused chassis upgrade for XV-02 and XV-02RS cars. The woven carbon fiber plates use multiple mounting holes and slotted positions to open up suspension setup changes, so shock geometry can be adjusted with more precision on paved running surfaces. The set contains 2 damper stays, 4 piston rods measuring 30.5 mm, 8 blue 5 x 6.55 mm ball connector nuts, and 8 round head socket screws in 3 x 10 mm size. The front and rear plates have distinct shapes for their mounting positions, with rounded outer edges, central slots and lower slotted openings that support different attachment points. That layout helps tune how the dampers sit on the chassis and how the suspension reacts through direction changes and corner entry. The supplied piston rods are specifically oriented for on-road performance rather than a general mixed-surface setup. On an XV-02 chassis, this set is used with Items 42102, 54465 and 54871; it also fits XV-02RS chassis cars. It suits builders refining a rally platform for asphalt sessions, club practice or repeatable setup testing where small geometry changes can be felt from one run to the next.
RC tuning parts
CC-01 Alum. Oil Damper Set, RC chassis upgrade
300054541€66.99
The CC-01 Alum. Oil Damper Set is an RC chassis upgrade made for the Tamiya CC-01 platform, using aluminum dampers to bring more composed suspension movement to cross-country running. On loose gravel, rutted tracks and uneven ground, the oil-filled design helps the chassis absorb repeated bumps with a steadier response than a basic friction setup. The set provides the parts needed to assemble 4 dampers, covering both front and rear positions for a balanced suspension layout. Each damper uses a silver anodized cylinder with a dark titanium anodized cap, giving the hardware a clean mechanical look that matches detailed off-road builds. V parts are included, along with small attachment parts for mounting to the chassis. The assembly sheet for the damper set notes standard oil as #400 and indicates separate front and rear spring use from the base kit. This upgrade suits builders refining a CC-01 for trail driving, rocky paths or mixed-surface sessions where repeated compression and rebound shape how the chassis settles after bumps. It also fits restoration or tuning work on an existing CC-01, where metal dampers can replace worn stock units with a full 4-piece suspension set. Warning! Not suitable for children under 14 years.
RC tuning parts
CC-01 Barrel Spring Set, chassis tuning springs
300054666€20.29
The CC-01 Barrel Spring Set adds a focused suspension tuning option to compatible CC-01 chassis cars, using 6 coil springs in 3 stiffness grades to change how the chassis reacts over rough ground. Its barrel shape creates progressive damping, which means resistance increases the further each spring is compressed, giving the suspension a more measured response when the surface starts to break up. The set contains 2 soft springs, 2 medium springs and 2 hard springs, making it possible to fit matched pairs and compare different setups with the same chassis. The springs are shown with colour bands that identify hardness at a glance, helping setup changes stay organised when several rates are on the bench. The shorter and longer spring forms in the set broaden the tuning range within the CC-01 platform and keep the adjustment centred on suspension behaviour rather than cosmetic changes. On loose tracks, gravel paths or uneven off-road sections, the progressive spring action supports a smoother ride and helps the chassis manage body roll with more control. For maintenance, replacement or planned tuning sessions, this spring set gives CC-01 owners a direct way to refine handling through a core suspension component.
RC tuning parts
CC-02 Damper Spring Set, RC chassis suspension parts
300054992€18.29
Built for CC-02 chassis cars, this damper set upgrades the suspension with 4 aluminum cylinders shaped for lower friction and a slimmer profile than the kit-standard cylinders. That narrower cylinder form changes the visual balance around the axles and gives the chassis a more scale-focused look while the dampers work through bumps, ruts and side-to-side weight transfer. Each damper uses cylinder caps, O-ring caps and adjustable retainers, with small attachment parts included to complete the installation. The top and bottom mounting points use ball connectors, replacing the kit's upper screw and collar arrangement. That mounting change supports smoother roll motion, especially when the chassis articulates over uneven ground or settles into off-camber sections. The set is intended to kit out a full 4-damper layout on the CC-02 platform rather than changing only one corner of the suspension. Compatibility stays flexible for tuning work, because the dampers can be paired with kit-standard springs or with the dedicated springs sold separately as Item 54992. This makes the set a useful choice for builders refining suspension response, scale appearance and chassis movement on trail-style RC vehicle builds.
RC tuning parts
CC-02 Full Ball Bearing Set, chassis tuning set
300054910€35.99
The CC-02 Full Ball Bearing Set is a focused chassis tuning upgrade for compatible CC-02 models, built around 22 metal bearings in 4 specified sizes. Installed in the rotating points of the chassis, the bearings support smoother movement and more efficient transfer of drive power than plain bushings, which helps the model run with less drag during use. The size mix of 2x 850, 16x 1150, 2x 1260 and 2x 1510 is matched to the CC-02 platform, so the set covers a full conversion with the required quantities already grouped in one pack. Ball bearings are often one of the first mechanical upgrades added to an RC chassis because they reduce friction where shafts and driven parts turn under load. That lower friction can also help reduce wear in those contact areas over time, especially on a model that sees regular running and routine servicing. During a rebuild, maintenance session or fresh chassis assembly, this set gives a direct route to replacing bushings with bearings across the specified CC-02 layout. The compact metal parts suit hobby benches where precise fit and orderly parts selection matter, and the pre-matched count keeps the upgrade process straightforward for the intended chassis family. Warning! Not suitable for children under 14 years.
RC tuning parts
CC-02 Motor Mt. Bridge Spacer, chassis accessory
300054971€27.29
The CC-02 Motor Mt. Bridge Spacer adds a focused chassis upgrade to CC-02 builds by reinforcing the motor mounting area with an aluminum part placed between the gearbox and the motor cap screws. That extra support helps keep the motor fixed in position, which contributes to a more efficient drive when the gears are set correctly and turning smoothly. The spacer also braces the gearbox against warping, giving the motor mount area firmer support under load. Its gun metal anodized finish matches the technical character of RC chassis hardware, while the curved bridge shape and elongated slots support accurate placement during fitting. The instruction diagram shows the spacer used with 3 x 14 mm cap screws and 3 mm washers while the motor position is adjusted to create proper gear backlash. This setup allows clearance for the gears to run lightly instead of binding at the mesh point. On a workbench build or a maintenance session, this part suits drivers refining drivetrain feel on a CC-02 chassis car. It can be fitted when replacing motor mount hardware, correcting gear mesh, or adding stiffness to the gearbox area for more consistent running across repeated sessions.
RC tuning parts
Clamp Alu Wheel Hub, accessory set, 5 mm blue
300053823€36.29
Clamp Alu Wheel Hub 4 5 mm blue brings a more secure wheel mounting setup to compatible Tamiya chassis through a split aluminium hub tightened by cap screws. The machined blue hubs sit neatly at the axle area and are designed to hold firmly during running, while the clamp construction also keeps 2 x 10 mm stainless steel shafts from slipping out when the hub is removed. This accessory set is intended for a broad range of chassis platforms, including TT-02, TT-02 Type-S, TT-02D, TT-01D Type-E, TT-01 Type-E, TT-01 Type-ES, TA07 PRO, TA06, TA06 PRO, TA06 MS, TA05 Ver.II, TB-04, TB-04 PRO, FF-04 EVO, FF-03, FF-03 PRO, TRF419, TRF419X, TB Evo.7, TB Evo.6, TB Evo.6 MS, M-07 Concept, XV-01T and XV-01 PRO. Use with item 53646 or 53647 is specified where required. The scope of delivery lists 1 Wheel Driver Set with 15 pieces, and the product image shows 4 blue clamp hubs, metal screws, pins and an L-shaped hex key. On a workshop bench, the cap screw fixing allows each hub to be tightened with a direct mechanical grip rather than a simple push fit. During maintenance, wheel removal and refitting stay controlled because the shaft hardware remains retained in the assembly, which helps keep small drivetrain parts organised between runs. Warning! Not suitable for children under 14 years.
RC tuning parts
Clamp Type Alum Hubs NarTrd (4), wheel hubs
300042352€20.99
Clamp Type Alum Hubs NarTrd (4) brings a focused chassis tuning option to touring car models with 4 narrow tread clamp type wheel hubs in aluminum. Mounted at the wheel area, these hubs allow a narrower tread setup that can be used at the front for sharper steering response, at the rear for improved grip, or across the whole car to tune overall balance on the track. Each hub uses a clamp type design and comes with 5 cap screws in 1.6 x 4 mm size for installation. The aluminum construction is finished in Tamiya blue anodizing, giving the parts a crisp technical look that stands out during maintenance and setup work. Compatibility covers TA06, TA06 PRO, TA06 MS, TA07 PRO, TA07 MS, TB-04, TB-04 PRO, TB-05 PRO, TB Evo.6, TB Evo.6 MS, TB Evo.7, TRF419, TRF419X, TRF419XR, TRF420 and TT-02 Type-S chassis. For use with 24 mm width medium-narrow wheels, and items 53646 and 54573 may be required. This set fits naturally into bench tuning before practice laps, race-day setup changes, or a rebuild focused on steering feel and rear traction. The 4-hub format supports a full car conversion, while the clamp layout keeps the adjustment centered on a small but influential chassis component.
RC tuning parts
CR-01 Reinforced Drive Shaft Diff Lock Set
300054108€46.49
Built for the CR-01 chassis, this reinforced drive shaft and diff lock set changes the axle drivetrain into a more direct, mechanically linked setup. The reinforced long and short drive shafts work with diff lock case A and diff lock case B to lock securely in place, supporting efficient power transfer when the axle is under load. The differential lock parts install in place of the bevel gears, as shown in the assembly layout, so the axle no longer relies on standard differential action. That change keeps both sides of the axle turning together, a setup often chosen for technical crawling lines where steady drive at both wheels matters. The set also uses 4 mm E-rings together with 3 x 6 mm screws and 2 x 5 mm cap screws in the assembly. Scope of delivery: 1 reinforced differential lock set with 14 pieces. As a chassis-specific tuning set, these parts suit CR-01 builds that need drivetrain components matched to the original axle housing layout. The black mechanical parts format also makes the upgrade easy to identify during maintenance, parts replacement or a fresh rebuild of the axle section. Warning! Not suitable for children under 14 years.
RC tuning parts
CR-01 Reinforced Wheel Axle, chassis spare pair
300054048€11.29
The CR-01 Reinforced Wheel Axle is a chassis spare pair made for the CR-01 platform and supplied as 2 matching replacement parts. Each axle uses stronger material than the standard version, giving this small drivetrain component a more durable basis where wheel-end hardware and repeated impacts concentrate force. The dark metal finish and machined form underline its role as a functional running part rather than a cosmetic add-on. Each piece combines a slotted lower section, a smooth central shaft with a cross-hole and a threaded tip, so the axle can take its place within the existing wheel assembly layout. The upgraded cup area brings improved wear resistance, targeting a contact point that sees repeated movement during running. That makes this pair a practical choice when a CR-01 build needs fresh axle hardware after demanding use on steep sections, uneven ground or hard descents. In workshop use, the pair suits routine maintenance, worn-part replacement or a durability-focused refresh of an existing chassis setup. For RC owners keeping a CR-01 ready for regular trail sessions, these 2 axles add a direct fit spare option centered on strength and wear performance. Warning! Not suitable for children under 14 years.
RC tuning parts
Damper Set Alum. M-Chassis (4), RC damper set
300054000€99.99
This aluminum damper set brings a chassis-specific suspension upgrade to M-Chassis builds with 4 oil dampers developed around a shorter format. The damper cylinders and damper rods are 2 mm shorter than touring car aluminum dampers, which lowers ride height and opens up more exact stroke adjustment on compact chassis layouts. The set is supplied as a 118-piece assembly package with threaded cylinders, adjustment nuts, springs, pistons, O-rings and mounting hardware. A hard black coating on the damper surfaces reduces friction, while the blue damper caps and white springs give the assembled suspension a crisp mechanical contrast. The internal setup can be tailored through piston choice, with 2-hole and 3-hole pistons specified for different chassis positions in the included build information. Standard damper oil is #400, and damper oil is available separately. On the bench, the set supports detailed front and rear suspension work for M-03, M-04, M-05 and M-06 chassis. It can also be used with TT-01 TYPE-E and TT-01D TYPE-E chassis together with 54059 and 54060, and with MF-01X chassis when the stated 5 x 9 mm cushion balls are added. The result is a more precisely tunable damper package for drivers refining ride height, spring tension and damping response. Warning! Not suitable for children under 14 years.
RC tuning parts
DB-01/TRF501X Pinion Gear 24/25T 48DP Set
300054218€16.79
The DB-01/TRF501X Pinion Gear 24/25T 48DP set adds a focused drivetrain tuning option to compatible RC chassis with 2 metal pinion gears in 24T and 25T sizes. The 48 pitch format and newly designed tooth profile are intended to reduce noise and friction loss, supporting a cleaner mesh and a smoother running feel during track sessions, maintenance work or ratio changes. Each gear uses 2 grub screw attachment holes, so the fastening position can be selected during installation on the motor shaft. The set also comes with 3 grub screws and an L-shaped hex key for fitting and adjustment. This makes the set useful both as a replacement for worn drivetrain parts and as a practical gearing option when refining acceleration, response or running characteristics on a supported chassis. Compatibility covers DB01-Chassis, DB02-Chassis, DN-01-Chassis, TD2-Chassis, TD4-Chassis, TRF201-Chassis, TRF201XMW-Chassis, TRF211XM-Chassis and TRF502X-Chassis. For TD2-Chassis and TD4-Chassis, use with 22031 is required. On the bench, the 24T and 25T choice allows quick comparison between 2 gearing steps while keeping the same 48DP standard across the setup. Warning! Not suitable for children under 14 years.
RC tuning parts
DB-01/TRF501X Reinforc.Belt, drive belt
300054140€11.99
This reinforced drive belt is a dedicated transmission spare part for the DB01, TRF501X WE and TRF511 chassis, combining a 369 size and 3.7 mm width with a toothed inner profile that transfers motion through the drivetrain. In a running model, that layout supports steady power delivery where the belt tracks around pulleys inside the chassis. The belt is supplied as 1 reinforced drive belt and is described as dust repelling, a detail aimed at keeping the drive path cleaner during operation. Its flexible construction is paired with low drive resistance, so the drivetrain can run with less drag while maintaining the belt's engagement on the teeth. The reinforced belt core is stated as about 1.5 times stronger than previous drive belts, and the reinforcement is also described as helping prevent tooth slip under load. That combination makes it a focused replacement part for restoring transmission performance on the named chassis. Used in maintenance, rebuilds or race-day spares, this belt suits model setups where the original transmission part needs replacement after wear. Kept in a pit box or workshop drawer, it gives the stated chassis platforms a matching spare for routine drivetrain service. Warning! Not suitable for children under 14 years.
RC tuning parts
DB01/TRF511 Gear Differential Unit 37T RC Part
300054329€43.99
The DB01/TRF511 Gear Differential Unit 37T adds a sealed oil-filled differential layout to compatible RC buggy drivetrains, replacing the kit-standard ball differential used on DB-01 and 511/502 chassis. That change opens another tuning route at the center of the transmission, where oil viscosity directly influences how quickly the differential moves under load on loose or changing off-road surfaces. Inside the assembly, a 37T pulley works with 12T and 20T bevel gears, while the sealed case uses a gasket, O-rings, shafts, shims and screws to hold the oil around the internal gear set. The instruction data specifies filling the case until the bevel gears are covered, making the working principle clear and easy to service. Higher viscosity oil slows differential movement, so the same unit can be adjusted for different grip levels and handling balance. Compared with a standard ball differential, this gear differential requires less frequent maintenance cycles. The included cross shaft from Item 54311 is supplied as standard, and the differential joint cups can also be sourced later as spare parts. On a prepared buggy, this unit suits drivers who tune for specific track conditions rather than leaving the stock setup unchanged. It also fits workshop maintenance sessions where a worn drivetrain is being refreshed with a sealed differential format that can be reopened, refilled and adjusted as running conditions change. Warning! Not suitable for children under 14 years.
RC tuning parts
DF-02/TT-01 Front One-way Unit, RC drivetrain set
300053671€84.99
The DF-02/TT-01 Front One-way Unit changes the front drivetrain layout by replacing the front differential gear with a one-way mechanism. Under power, the front end keeps traction engaged; when throttle is off, the difference in rotation between front and rear wheels is canceled, supporting smoother, stall-free cornering on technical sections and tighter turns. The set contains 19 parts and is built around the one-way ring gear, left and right front one-way housings, one-way joints, bearing spacers and 1060 flanged ball bearings. During assembly, the housing and ring gear holes are aligned and secured with 2 x 8 mm cap screws using the included 1.5 mm hex wrench. The instructions also note a 6 mm washer adjustment when a universal shaft shows excess play at the one-way joint, giving a clear mechanical route to fine-tuning fit. Fitment details matter with this upgrade. TT-02 TYPE-S and TT-02 TYPE-SR chassis use it together with 53590, TT-02B requires the 6 mm O-ring MB16 in the connection cup, and TT-02RR uses the kit wheel axle and driveshaft together with 53590. For DF-02 and TT-01 based builds, this unit suits tuning sessions focused on front-end response and drivetrain behavior rather than cosmetic changes alone. Warning! Not suitable for children under 14 years.
RC tuning parts
DF-03 Damper Spring Set, chassis tuning set
300053927€26.99
The DF-03 Damper Spring Set adds a focused suspension tuning option for compatible RC buggy chassis by putting 12 metal coil springs with 3 distinct hardness levels into one pack. Soft black, medium gold and hard silver springs give a clear starting point for adjusting how the dampers react to bumps, grip changes and direction shifts on different surfaces. The 3x4 configuration supplies a full set arrangement, so matching spring rates can be fitted across the vehicle instead of mixing unrelated parts. On loose dirt, a softer rate can help the suspension move more freely over uneven ground, while firmer springs suit higher-grip sections and route layouts that call for a tighter response. The color coding speeds up setup checks between runs because each hardness level is easy to identify at a glance. This set is specified for DF-03, TT-02B, DB02, DB01, DN-01 and TRF201 chassis, and TT-02B use is stated together with 53926. At the bench, the springs give a direct way to test setup changes before the next battery pack goes in. On the track, that means suspension tuning can follow the road surface and course shape more closely, whether the goal is a calmer reaction over rough sections or a firmer feel through faster lines. Warning! Not suitable for children under 14 years.
RC tuning parts
DT-02 Alu. Servo Mount, chassis accessory set
300054397€17.99
The DT-02 Alu. Servo Mount is a chassis accessory set for the DT-02 platform, built around aluminum parts that bring a clean, technical upgrade to the steering installation area. The compact L-shaped mounts and matching hardware suit maintenance benches, replacement work and fresh chassis builds where a dedicated servo fixing part is needed. The set contains 10 servo mount pieces, making it useful for keeping matching spares on hand across repeated rebuilds or service intervals. The included parts shown with the mounts support fastening during installation, while the metal construction gives the assembly a crisp, precise look inside the chassis layout. As a model accessory rather than a complete vehicle, this set focuses on one specific task: securing the servo mount position on the DT-02 chassis with parts made for that platform. On the workbench, the pack fits naturally into parts sorting, repair sessions and planned upgrades for an existing DT-02 setup. It also suits builders who keep replacement hardware ready between runs, so the next maintenance job can move straight to fitting and alignment with the correct mount parts close at hand. Warning! Not suitable for children under 14 years.
RC tuning parts
DT-02/DT-03 Spring Set, RC damper tuning kit
300053832€26.99
This spring set expands the suspension setup range for DT-03, DT-03T and DT-02 chassis that run with CVA dampers. The pack contains 8 coil springs, with 2 soft and 2 hard springs for the front and the same combination for the rear, giving a direct way to tune the chassis for different road conditions. A key detail lies in the spring design itself: the softer springs use a longer free length, while the harder springs use a shorter free length. That difference keeps vehicle height unchanged when swapping between the two rates, so spring choice can focus on suspension response rather than ride-height correction. The set is intended for use with the DT-03 CVA oil damper set, the CVA oil damper set mini and the CVA oil damper set short, making it a focused upgrade for compatible buggy layouts. On loose ground, mixed surfaces or a familiar practice track, this set supports quick chassis experiments with front and rear balance. It suits builders who want to compare softer and firmer damping support on the same compatible platform and refine handling with a simple spring change. Warning! Not suitable for children under 14 years.
RC tuning parts
DT-03 Alum. Battery Bar, chassis accessory
300054564€13.59
The DT-03 Alum. Battery Bar is a dedicated chassis accessory for DT-03 models, built to hold the battery with a firm, rigid retainer. Its lightweight aluminum construction keeps the part focused on secure battery mounting while fitting the technical character of RC buggy maintenance and upgrade work. The bar uses a machined aluminum form with a blue anodized finish and is supplied with the small attachment parts needed for installation. This combination gives the chassis a clearly defined battery restraint that supports a neat internal layout around the battery bay. As a model supply rather than a complete vehicle, the part is intended for fitting into an existing DT-03 build where battery retention matters during repeated running sessions. The dedicated compatibility with DT-03 chassis models keeps selection straightforward for matching repairs or planned upgrades. On the workbench, the bar suits routine servicing, replacement of a worn retainer, or a fresh custom build based on the DT-03 platform. Once installed, it becomes part of the battery mounting setup inside the chassis, supporting a more secure hold where movement of the pack needs to be controlled by the fitted hardware.
RC tuning parts
DT-03 Carbon Damper Stay Front RC Chassis Part
300054562€19.49
The DT-03 Carbon Damper Stay Front is a chassis upgrade part for DT-03 cars that brings a stiffer front damper mounting point to the suspension layout. Its carbon plate construction and symmetrical multi-hole pattern give the front end a clean, technical setup for damper installation, with the curved upper edge and twin lower tabs shaped to match the chassis mounting area. This set is supplied as ITEM 54562 and is intended to replace the standard C5 part on the DT-03 platform. The included hardware consists of 2 ball connector nuts, 2 3x8 mm screws and 2 3x0.7 mm spacers, which match the mounting points shown for the stay itself. The drilled positions allow adjustment of damper attachment points, which helps builders alter front suspension geometry through the mounting location rather than through unrelated chassis changes. The part is documented for use in place of C5 and for compatibility with the DT-03 CVA Damper Set. On a buggy prepared for loose dirt, compacted track sections or repeated jump landings, the front stay gives the suspension area a more focused base for setup changes. It suits workshop tuning sessions where front damper position, linkage fit and chassis response are adjusted step by step on a DT-03 build.
RC tuning parts
DT-03 Carbon Damper Stay Rear, chassis upgrade
300054563€22.59
The DT-03 Carbon Damper Stay Rear brings a focused chassis upgrade to DT-03 models by combining carbon fiber construction with a rear suspension mounting layout designed for tuning. The flat carbon plate gives the dampers a rigid mounting point, helping the suspension work with a more direct, controlled feel during running sessions. A series of mounting holes across the stay creates more setup scope than a fixed-position part. Damper angle and mounting position can be adjusted to explore different handling responses, making the part useful for track tuning as well as routine chassis refinement. The set also contains the small attachment parts needed for installation, so the carbon stay can be fitted as a complete rear mounting component rather than as a bare plate alone. The instruction data identifies it as a replacement for the standard stay position on DT-03 chassis models. On a prepared buggy, this kind of upgrade comes into its own when surface grip, corner entry and rear stability need closer adjustment through damper position changes. It also suits workshop builds that focus on replacing standard chassis parts with lighter, more rigid option components matched to the DT-03 platform. Warning! Not suitable for children under 14 years.
RC tuning parts
DT-03 Full Turnbuckle Set, RC chassis upgrade
300054572€22.49
The DT-03 Full Turnbuckle Set adds adjustable linkage hardware to DT-03 chassis cars, replacing fixed upper arms and tie-rods with 6 stainless steel turnbuckle shafts. Threaded adjustment makes it possible to fine-tune link length for a more exact chassis set-up while the buggy sits on the bench between runs. The set includes 2 shafts in 3x32 mm, 2 in 3x38 mm and 2 in 3x65 mm, covering the different positions used around the chassis. Each shaft uses an adjustment section that can be turned with the included wrench, so changes can be made without removing every linkage point first. Stainless steel construction gives the shafts a clean, precise finish suited to repeated set-up work, and the supplied attachment parts support installation on compatible DT-03 models. This upgrade suits drivers who want to refine alignment after a rebuild, correct steering link length, or make measured suspension changes for different running conditions. On a maintenance table, at a club session, or between outdoor buggy runs, the set gives the DT-03 platform a more tunable linkage layout with parts sized for direct compatibility.
RC tuning parts
DT-03 Gear Shaft, RC spare part, 5x45mm pair
300054560€3.49
The DT-03 Gear Shaft lightweight 5x45mm set is a focused drivetrain upgrade for DT-03 chassis cars, replacing the shafts used with the spur gear and counter gear. Its pipe construction cuts weight at a rotating point in the transmission, which supports a lighter, more efficient drive layout during buggy running. Each shaft measures 5x45 mm and the set contains 2 matching pieces for the specified replacement point. The hollow metal form does more than change mass: it also helps dissipate heat, which is especially useful around the drivetrain area where moving parts work continuously. Because the change is concentrated in the gear shaft position, the upgrade targets mechanical efficiency without altering the stated DT-03 fitment. This set suits maintenance, repair, or a planned drivetrain refresh on compatible DT-03 chassis cars. Kept as workshop spares or fitted during a rebuild, the 2 shafts offer a straightforward way to swap out the standard kit parts with a lighter alternative matched to the same application.
RC tuning parts
DT-03 Rein M Part DS Mount, chassis spare parts
300054816€6.29
The DT-03 Rein M Part DS Mount brings a focused chassis update to DT-03 cars with carbon-fiber reinforced resin parts shaped for key structural positions. On the sprue are a damper stay mount, wing stay, front bumper parts and additional matching components that replace standard sections exposed to repeated load during running. The carbon-fiber reinforcement changes how these areas respond under stress, giving the chassis a firmer feel on high-grip carpet and asphalt where traction can place more force through the suspension mounts and bumper area. As a dedicated M parts sprue, this set suits repair work after wear as well as targeted tuning when a DT-03 setup needs more support in the front and rear mounting zones. The moulded layout also keeps each piece grouped for straightforward identification during parts selection. In workshop use, the set fits naturally into routine maintenance for a buggy that has seen frequent track sessions or repeated contact with barriers and jumps. It also serves as a practical upgrade path when preparing a DT-03 chassis for grippier indoor carpet or clean asphalt running, where a more rigid structure can help the car respond with greater consistency.
RC tuning parts
DT-03 Stabilizer Set Front/Rear RC Chassis Tuning
300054561€21.79
The DT-03 Stabilizer Set front/rear adds a focused suspension tuning option to DT-03 and DT-03T chassis cars by fitting sway bars at both ends of the car. Once installed, the bars reduce chassis roll and help the car carry a more even balance through changing off-road track conditions, whether the surface is loose, grippy or uneven. The set provides 2 stiffness choices for the front and 2 for the rear, with soft red rods and hard blue rods for setup changes. That gives room to adjust how strongly each end resists roll instead of locking the chassis into a single response. The included parts go beyond the bars themselves, with stabilizer ends, 5 mm ball connectors, screws, grub screws and a 1.5 mm hex wrench supplied for assembly. The manual notes front rods in 1.4 and 1.6, and rear rods in 1.4 and 1.8, adding another concrete reference for setup selection across the front and rear suspension. On a prepared dirt track, a looser surface or a layout with repeated direction changes, this tuning range helps tailor the car to the conditions rather than leaving the suspension in one fixed state. For drivers refining a DT-03 buggy or DT-03T truck, the set adds a direct way to adjust roll behavior through hardware mounted on the chassis itself.
RC tuning parts
DT-03/02 19T Steel Pinion Gear, M0.8 Accessory
300054629€5.89
This M0.8 module 19T steel pinion gear is a focused drivetrain upgrade for compatible chassis cars, pairing a compact motor-side gear with a tougher material choice for repeated running sessions. The steel construction is stated as more durable than the kit-standard aluminum pinion gear, helping reduce wear at a part of the transmission that sees constant tooth contact. The gear is supplied as 1 piece and comes with a grub screw for attachment, so the pinion can be fixed directly to the motor shaft in the intended position. The 19-tooth specification keeps the gearing at the stated tooth count, which matters when maintaining an existing transmission setup rather than changing to a different ratio. The M0.8 module matches the stated gear format, giving a clear fit reference alongside the chassis compatibility. Compatible DT-03 and DT-02 chassis cars can use this part as a replacement when the original pinion shows wear or when a steel version is preferred for longer service life. In workshop use, this kind of part suits routine drivetrain upkeep between running sessions, especially when a worn motor pinion starts to affect mesh quality. It also fits neatly into a spares box for chassis-specific maintenance, ready for the next rebuild or transmission refresh.
RC tuning parts
DT-03/02 Ball Diff.-Set, RC drivetrain upgrade
300053863€51.99
The DT-03/02 Ball Diff.-Set is an RC drivetrain upgrade for compatible DT-03 and DT-02 chassis, built to add a ball differential with limited slip effect. That setup improves traction and mobility while keeping the car more settled in fast cornering, so power delivery feels cleaner when the rear end is working across changing grip. Inside the assembly, the gear width is reduced from 20 mm to 15 mm, a change that cuts friction loss in the drivetrain. The set contains 29 parts and includes 2 17 mm thrust washers, 10 steel balls, 1 1150 thrust bearing, 1 diff gear, 1 stepped bolt, pressure plate A, pressure plate B, a pressure plate cap, and long and short gearbox joints. The included grease shown for the ball differential supports the contact surfaces during setup and running. This differential layout also helps protect the gears from damage and wear by managing load through the drivetrain more effectively. Compatibility covers selected DT-03 and DT-02 chassis models such as NEO FIGHTER, RACING FIGHTER, DESERT GATOR, SAND VIPER, NEO FALCON and HOLIDAY BUGGY. For operation, universal joint shafts 300053791 or shaft set 309805551 with 300050823 are required separately. This makes the set a focused choice for tuning an existing buggy with a more adjustable differential action and a drivetrain setup aimed at traction and cornering stability. Warning! Not suitable for children under 14 years.
RC tuning parts
DT-03/02 M0,8 Module 17T Steel Pinion Gear
300054628€5.89
The DT-03/02 M0,8 Module 17T Steel Pinion is a drivetrain upgrade part for compatible chassis cars, built to place a steel gear at the point where motor output transfers into the transmission. Its M0,8 module and 17-tooth layout define the meshing geometry, while the compact pinion format keeps the part focused on clean, direct power delivery inside the gear train. Compared with the kit-standard aluminum pinion gear named in the data, this steel version is intended for greater durability and increased gear life during repeated running. The straight-cut teeth and central bore create the working interface, and the side fixing point uses the included grub screw to fasten the gear onto the shaft. The set contains 1 pinion gear and 1 grub screw, keeping the replacement focused on the essential mounting hardware. The black metal finish and engraved top-face marks give the part a technical, workshop-ready look that matches its mechanical role. In a maintenance setup, this gear suits rebuilds after drivetrain wear or ratio changes that call for a 17T pinion in the specified module. It also fits neatly into a spares box for DT chassis servicing, where a correctly matched steel pinion helps keep compatible RC cars running with the intended gear mesh.
RC tuning parts
DT02&TT01 3x22 LF Sus. Shaft, RC spare parts
300054395€8.19
The DT02&TT01 3x22 LF Sus. Shaft set is a focused RC hardware upgrade for compatible Tamiya chassis, replacing 3 x 22 mm screw pins with shaft parts secured by E-rings. That change gives suspension link points a firm mechanical hold while keeping the assembly compact and precise around moving components. Each shaft has a low-friction coating that supports smoother suspension action as the linked parts cycle through movement. The set includes 4 silver metal shafts with machined grooves and 10 matching E-rings for installation. This configuration suits maintenance work on worn hardware, a planned rebuild, or a fresh chassis assembly where the specified shaft format is required. The grooved ends provide the retention points for the E-rings, so the fastening method is built into the part itself rather than relying on threaded screw-pin installation. Compatibility covers DT-03, DT-03T, DT-02, TT-02RR, TT-02D, TT-02 and WR-02 chassis. In workshop use, the parts support clean replacement of existing suspension hardware and help keep moving assemblies operating with a consistent mechanical feel across repeated runs. Warning! Not suitable for children under 14 years.
RC tuning parts
F-104 HT Saver Alu. Horn, servo horn, blue aluminum
300054159€25.49
The F-104 HT Saver Alu. Horn is a machined aluminum servo horn for the High Torque Servo Saver, created to replace the Q5 section and give the steering system a firmer, more direct feel. Its anodized blue finish makes the part easy to identify during a build or maintenance session, while the metal construction targets stiffness in the steering area rather than changing unrelated chassis parts. This servo horn is specified for the High Torque Servo Saver 300050473 in white and 300051000 in black. The stated fit list also names F104 and the F103 15th Anniversary Chassis Kit Item 84056, plus DT-03 and DT-03T chassis. Further listed applications include TB Evo.7, M-08 CONCEPT, F104VerⅡ, TRF101, DT2 and DT4, showing that the part serves as a focused steering upgrade across multiple supported platforms. The change in material from the standard saver section to machined aluminum is aimed at reducing flex in this specific linkage point. In workshop use, this part suits builders refining steering response on compatible chassis or replacing the original saver horn with a stiffer alternative. It fits naturally into maintenance, rebuild and tuning routines where exact servo saver behavior matters on the bench and on the track. Warning! Not suitable for children under 14 years.
RC tuning parts
F104 Alu Clamp Type Wheel Stopper, chassis part
300054240€16.79
The F104 Alu Clamp Type Wheel Stopper is a chassis part for all F104 chassis, built around a clamp mechanism that secures the shaft by tightening the slot in the stopper with a cap screw. That layout gives a controlled hold at the shaft while keeping adjustment work more precise during setup and servicing. A key detail of this design is its handling on carbon shafts. The stopper can be repositioned with subtle changes in placement without damaging the shaft surface, which matters when fine tuning drivetrain or wheel-related alignment on an F104 platform. The aluminium construction adds a crisp mechanical feel to repeated workshop use, and the clamp format avoids the more awkward handling that can come with installing and removing bearings in this area. On the bench, that means maintenance work around the shaft section can move forward with fewer interruptions when parts need to be checked, shifted or refitted. The included rim driver set with 4 pieces supports fitting and adjustment tasks, making this a focused upgrade part for keeping an F104 chassis easier to service and more exact to set up over repeated running sessions. Warning! Not suitable for children under 14 years.
RC tuning parts: get the best out of your RC model!
With RC tuning parts, you can give your vehicle a personal touch and take its performance to the next level. Whether you want to make your RC car faster, more stable, or visually unique – you'll find the right tuning options with us to make your hobby even more exciting.
Why RC tuning parts are a must for your model
More performance, more driving fun
With the proper RC tuning parts, your model will not only stand out visually, but it will also have significantly improved driving characteristics. RC aluminium tuning parts such as shock mounts and wheel axles provide more stability and durability, ensuring you maintain full control even at high speeds or on rough terrain. Additionally, specialised motor pinions or servo mounts allow you to increase acceleration and precision. This means: even more adrenaline with every race!
Visual customisation
RC tuning isn’t just about performance – it’s also a way to make your model unique. With stylish tuning parts made from aluminium or other high-quality materials, you can give your RC car a truly personal touch. Whether it’s vibrant colours, cool rims, or custom body parts – your RC model is guaranteed to turn heads on the track.
The joy of building and optimising
A key part of RC model building is the enjoyment of tinkering and customising. With the right RC car tuning parts, you can adjust the driving behaviour to suit your needs and get immediate feedback on your work – a rewarding experience that is sure to thrill! From improved control arms to special wheel hubs: every tuning part brings your model closer to perfection.
Find the right RC tuning parts for your model
Excited to try RC tuning? Then browse through our selection and discover high-quality RC tuning parts for your model. Whether you're looking for RC aluminium tuning parts or specific components for your vehicle – we offer a wide range that makes RC car tuning a real adventure. Make your model unique and feel the difference with perfectly matched tuning parts.