RC Shock absorbers & RC springs
Discover high-quality shock absorbers and springs for RC vehicles: for perfect handling and optimum suspension, so that your model keeps going in any situation and masters bumps effortlessly!
RC Shock absorbers & RC springs
Discover high-quality shock absorbers and springs for RC vehicles: for perfect handling and optimum suspension, so that your model keeps going in any situation and masters bumps effortlessly!
More
Shock absorbers & springs
Alum. Damper Retainer -1mm, RC part, blue anod
300053876€27.99
The Alum. Damper Retainer -1mm is a suspension tuning part for compatible RC chassis, combining machined aluminum construction with a blue anodized finish and a precise fit around the damper spring area. By lowering the spring set position by 1 mm compared with the aluminum mount of the OP595TRF shock, it supports a lower vehicle height and a more exact starting point for chassis setup. This set contains 4 spring plates for matched installation across the suspension. The rigid aluminum holder is made for reliable initial adjustment of the damper spring, helping setup changes translate more directly at the shock. Compatibility extends beyond the main chassis list: on TD4 and TD2 chassis, only standard front dampers can be installed. On MF-01X chassis, use with 42102 or 42273 or 42354 or 42355 or 54000. On F104 and F104W chassis, use with 53901. In workshop use, the 1 mm change gives a concrete option when refining stance and spring preload on touring, formula, or off-road based builds that share these chassis families. The 4-piece set suits rebuilds, replacement work, or a fresh suspension setup where consistent hardware across the dampers matters. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
Aluminium Shock Absorbers, 55.62 mm, 2-Piece Set
300053155€51.99
These aluminium shock absorbers bring a low-friction damper setup to compatible Tamiya M chassis models, combining a machined cylinder interior with a 55.62 mm overall assembled length. The metal damper design is intended for smooth operation, giving the suspension a more even response as the shafts move through the cylinder. Compatibility covers the M-06 chassis, M-06 PRO chassis, M-05 ver.II PRO chassis, M-05 chassis and M-05 PRO chassis. The set contains 2 shock absorbers and is supplied with 48 pieces for assembly, including the hardware and sealing parts needed for the damper build. Aluminium bodies, coil springs, shafts, rod ends, clips and rings form a detailed suspension set that suits replacement, rebuilding or chassis tuning work on the listed platforms. Mounted on a compatible M chassis, the dampers support controlled suspension movement during cornering, braking and direction changes. The purple finish gives the underbody a distinctive technical look, while the complete 2-piece configuration fits neatly into workshop sessions focused on maintenance, setup changes or restoring smooth damper action. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
Axle Spring (2) 58416, model spare part
309805304€0.89
Axle Spring (2) 58416 is a model spare part for the axle area, supplied as a 2-piece spring set under the stated 58416 designation. The format suits maintenance tasks where a matching replacement is needed for a worn, missing or no longer usable spring in a compatible model assembly. The focus here is clear part identification rather than broad fit claims. The ShortDescription names the component as an axle spring, and the pack count confirms 2 springs in the set. That makes the set useful for organised parts storage, planned servicing and direct replacement work where the correct designation matters. In a workshop drawer or spares case, the numbered reference helps separate this spring set from gears, shafts, screws and other maintenance components. During repair or upkeep, a dedicated replacement spring set can help return the axle section to its intended mechanical role in the assembly. The compact 2-piece format also suits keeping a matched pair on hand for future service jobs on compatible model builds. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
BB-01 Damper Adjuster V Parts, RC spare set
310225338€6.49
The BB-01 Damper Adjuster V Parts set brings front and rear damper adjuster components together on one black molded sprue for focused repair and maintenance work. Shaped rings, collars and linking pieces are arranged as separate numbered sections, so the required part can be identified before removal and fitted where the BB-01 chassis calls for it. The visible sprue layout supports clean handling at the bench, with each molded section kept in place until use rather than arriving as loose pieces. This format helps when comparing part shapes, checking orientation and separating only the needed component during a repair. The set belongs to the model supplies category and is intended for RC and model servicing rather than stand-alone play. Its compact collection of adjuster parts concentrates on one chassis area, which keeps replacement work specific instead of relying on mixed universal hardware. On a workshop table, the numbered sprue can be checked against the relevant build stage or service task before installation. For an existing BB-01 build, the set provides a direct source for renewing front or rear damper adjuster parts when the original pieces need replacement.
Shock absorbers & springs
Bumper Ford Ranger Subaru Brat model spare part
319335553€19.99
This replacement bumper supports repair and upkeep on selected Tamiya vehicle builds by restoring a small but visible body detail in a single swap. The part is supplied as 1 piece and is identified in the source data for Ford Ranger and Subaru Brat applications, making it a focused choice for maintenance rather than a general universal fitting. The black moulded form shows multiple mounting points and a shaped center section that align it with model assembly hardware and body attachment areas. That layout helps when sorting spares on the bench, checking compatibility during a rebuild, or replacing a missing section after use. The source data also links the part to Sand Scorcher 58441 and 58452 references, which adds another concrete route for matching it to an existing build or parts collection. As a single replacement component, it suits targeted repairs where the rest of the vehicle remains in serviceable condition. In workshop use, a dedicated spare like this keeps restoration work moving without replacing larger assemblies. It also fits neatly into labelled parts storage for future rebuilds, especially where older Tamiya models are maintained over time and original trim details need to be brought back into place. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
C.V.A II Oil-Shock-Set Super Short, damper set
300050746€26.49
The C.V.A II Oil-Shock-Set Super Short is a 48-piece damper set for assembling 2 extra short oil dampers for RC chassis applications. Its shortened format suits layouts where suspension space is tight or where a lower chassis ride height is needed without moving away from an oil-filled damper design. The set is supplied as 1 oil damper set and is intended for model use from 14 years. This version is designed for MF-01X chassis use and also matches the TT-02RR chassis, where it serves as kit standard equipment. The assembly diagrams show the working structure in detail: piston rods fit into the cylinders, O-rings and E-rings secure the moving parts, damper oil is filled into the cylinder, and the piston is moved through the oil to release trapped air before the cap is tightened. Spring installation is completed with dedicated adjuster parts, allowing the suspension unit to be built to the required kit setting. That sequence gives the set clear value for replacement, rebuild and chassis-specific tuning work. On the bench, the compact damper length helps when refreshing an existing suspension layout or preparing a chassis for a lower stance. For MF-01X rear use, 5x9 mm pillows, 19805611, are required separately. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
C.V.A-Mini II Shock Seal Set, RC spare part
300050600€4.69
The C.V.A-Mini II Shock seal set supplies 6 green damper sealing caps for suspension maintenance on selected RC chassis. As a replacement for 50519, this spare part supports rebuilds where original seals are worn, missing or being refreshed during routine workshop service. The set is standard equipment for the TT-02RR chassis, which makes it a direct match when restoring that platform to its original specification. It can also be used on TT-02, TT-02D and TT-02FT vehicles equipped with 50746, on TT-01 TYPE-E vehicles equipped with 53619, and on DT-03 and DT-03T vehicles equipped with 54567. The scope of delivery contains 6 damper sealing caps, giving a defined quantity for planned maintenance rather than a loose compatibility note. DT-02 XB cannot be used, and on DN-01 chassis this part cannot be combined with 54028. In workshop use, these caps suit scheduled damper service, replacement of lost parts, or preparation of a chassis before the next running session. The clearly stated chassis references help match the set to the correct suspension layout before installation and avoid ordering the wrong spare part. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
C.V.A.II Oil Damper Set Mini, RC shock set
300050519€36.29
The C.V.A.II Oil Damper Set Mini adds an oil-filled suspension option to compatible RC chassis and brings a more tunable setup to compact model car builds. Supplied as a 2-piece set, it is designed for builders who want to replace or refine standard dampers with an adjustable unit that can be matched to different mounting positions. Each damper can be adjusted from 55 to 70 mm, giving the set a usable range for several chassis layouts named in the compatibility list. The set is suitable for TD4, TD2, DB02, DB01, DF-03, DF-02, DT-02, DT-03, F103GT, GF-01CB, TT-02B, TT-01 TYPE-E and WR-02CB. The included damper oil supports the oil-pressure design, where the internal fluid works with the spring and shaft movement to manage compression and rebound during running. This makes the set relevant not only as a replacement part, but also as a tuning step when suspension response needs to be matched more closely to the chassis setup. On a bench build, the adjustable length helps when preparing a specific front or rear suspension position before installation. During running sessions, the oil-filled construction supports more measured chassis movement over changing surfaces and through repeated direction changes. For installation, 5 mm ball heads are required separately. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
C.V.A.II Oil Damper Set Short, RC shock set
300050520€39.49
The C.V.A.II Oil Damper Set Short brings oil-filled suspension control to a wide range of RC chassis, with 2 short dampers designed for tuning or replacement use. Its adjustable 80 to 97 mm length gives room to match the setup to different vehicle layouts, helping the suspension work with the chassis rather than against it on rough sections and changing surfaces. This set is suitable for TD4, TD2, CW-01, DB02, DB01, DF-03, DT-02 and TT-02B chassis, and the data also names Monster Beetle, Blackfoot, Lunch Box, Midnight Pumpkin, Manta Ray, Top Force, Force and Blitzer Beetle among the compatible models. That broad fit makes it useful both for restoring an older runner and for refining the handling of an active build. The oil damper format uses fluid resistance inside the shock body to smooth compression and rebound, giving a more measured suspension action than a simple friction-based setup. On the bench, the pair suits maintenance, repair and chassis-specific tuning work where damper length matters. A 5 mm ball head is required for mounting, with part 300050592 required separately, so the set can be installed with the correct attachment hardware for the chosen model. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
Damper Bag BF1-8, spare parts set for 58441/58452
319401427€44.99
The Damper Bag BF1-8 is a spare parts set for the Tamiya references 58441 and 58452, bringing 28 damper-related components together in one pack for targeted maintenance work. Silver tube sections, rods, caps, bushings and translucent spacer rings form a compact hardware assortment that suits repair tasks where the original suspension parts need replacement. The included contents are listed as 1 damper set with 28 pieces, making the pack a focused source for the small components that are often needed during servicing. The BF1-8 designation helps identify the correct parts group for the stated model numbers, which is useful when matching replacement hardware to an existing build. The mix of metal-look and molded parts shown for the set points to several connection and spacing functions within the damper assembly rather than a single loose replacement part. On the workbench, this set fits routine model upkeep, rebuilds after wear, or the replacement of lost small parts during disassembly. For compatible 58441 and 58452 builds, the grouped contents make it easier to restore the damper area with matching pieces kept together in one set. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
Damper Bushing, model spare part set of 8
319808279€12.29
This set provides 8 damper bushings for model maintenance and replacement work, giving matching inserts for assemblies that use this compact flanged format. Each piece is shown in black with a cylindrical body, a central hole and a lip on both sides, a shape that supports seated placement in the intended mounting point. The small format makes the set useful when a worn insert needs to be exchanged or when spare bushings are kept ready alongside other service parts. Because all 8 pieces share the same form, the pack supports consistent replacement across the same assembly area. The through-hole design suits fastening or guided pass-through where the matching model layout calls for a bushing, while the flanged edges help the part sit in place within the corresponding opening. On the workbench, this kind of spare part belongs in regular upkeep for model vehicles and related mechanical builds that use damper-mounted components. The set can be used during repair sessions, rebuilds or planned maintenance, where fresh bushings help return the intended fit of the original assembly. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
DF-03 B-Parts Damper Stay, chassis spare part
300051249€11.99
The DF-03 B-Parts Damper Stay set is a chassis spare part made for the DF-03 platform and supplies front and rear stay components in one pack. Its molded black parts follow the original mounting pattern, so repair work can focus on restoring the suspension mounting area with the correct fit for this chassis. Several hole positions are built into the stays, giving the assembly clear fastening points where dampers and related hardware attach. Ribbed reinforcement details are formed into the parts, and the set also shows a metal brace element fixed with screws and washers for added structure in the mounting section. This combination suits routine maintenance, replacement after wear, or rebuilding a used chassis with the proper B-parts section rather than mixing unmatched components. On the bench, the set supports a straightforward refresh of damaged front or rear mounting points on a DF-03 build. It also fits parts storage for racers and hobby workshops that keep chassis-specific replacements ready for service between running sessions. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
DT-01 Damper Bag, RC spare part for 58205
309415375€14.89
The DT-01 Damper Bag for 58205 is an RC spare part set built around 4 matching suspension units with red molded bodies, silver coil springs, inner rods and mounting eyelets at both ends. These parts are shaped to connect directly into the suspension layout of the specified model, restoring the moving link between attachment points when the original dampers are worn or damaged. Each damper combines a cylindrical upper housing with a visible spring wrapped around the center section, plus a lower end designed for secure mounting. That construction matters during maintenance because the spring and rod assembly allows controlled suspension movement instead of a fixed connection. The matching format across all 4 parts also supports balanced replacement work on multiple corners of the chassis rather than mixing different damper types. As a dedicated DT-01 spare part for 58205, the set is focused on repair, upkeep and keeping the running gear mechanically complete. On the bench, the bag suits routine servicing, rebuilds after heavy use and the replacement of missing or tired suspension parts. Once fitted, the dampers return the model to a setup with the correct spring-supported linkage for rolling, steering and general chassis movement. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
DT-02/03 B Parts, axle pad holder spare sprue
300004252€5.49
This spare B parts set supplies the Fighter axle pad and holder components for DT-02 and DT-03 chassis work, giving repair and maintenance builds the exact molded section needed for a clean replacement. The black parts are supplied on 1 sprue, so the full group stays together until the required section is removed and fitted. The set is specified as B parts for Super Fighter G DT-02 reference 58340, which makes it a focused choice for restoring the original layout rather than substituting unrelated hardware. The sprue format also helps with bench organisation, because each connected section remains easy to inspect before trimming. The visible molded structure supports careful handling of smaller mounting areas while the remaining pieces stay attached to the runner. For workshop stock, a single replacement sprue is also straightforward to sort and store alongside other chassis-specific service parts. This set suits rebuilds after wear, damage or missing pieces, and it also fits planned maintenance when a chassis is already apart for service. On the workbench, the connected layout makes it easier to compare the replacement section with the installed part before the swap begins. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
DT-03 C Parts, chassis damper stays spare set
319000626€16.49
DT-03 C Parts provide replacement chassis and damper stay sections for selected RC model builds, with the main components supplied on a grey injection-moulded sprue for clear identification before removal. The set is intended for maintenance work, rebuilds and parts replacement where the original mounting sections need a direct-format spare. The sprue layout groups multiple structural pieces in one frame, including the chassis and damper stay elements named in the product data. That format helps keep the parts together during storage and bench work until each section is cut free for installation. The moulded construction suits the precise shapes needed around mounting points and connected assemblies. Compatibility is stated for 47347, 47371, 57872, 57895, 58587, 58628 and 84435, which gives a clear reference for matching this spare set to the correct vehicle platforms. On the workbench, this set fits naturally into routine service jobs after wear, damage or a full strip-down of the model. It also works as a practical stock spare for hobby rooms where frequently used chassis sections are kept ready for the next repair session. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
DT-03 CVA Damper Set Short/Mini RC Chassis Parts
300054567€33.99
The DT-03 CVA Damper Set Short/Mini brings oil-filled suspension action to a range of Tamiya off-road chassis cars, replacing basic friction-style movement with a more refined damper setup. With 2 mini shock units and 2 short shock units, the set equips 1 complete chassis and gives front and rear suspension the controlled compression and rebound needed for cleaner handling on loose ground and uneven sections. Inside the set are the parts for 4 assembled dampers, including damper bodies, piston rods, springs, seals and hardware. During assembly, oil is added to each cylinder and the piston is moved slowly to release trapped air before the cap is tightened, creating the internal damping effect that defines the CVA design. Separate front and rear assemblies use different parts and oil seals, and spring spacers are fitted to adjust preload after the springs are installed. The dampers mount to the chassis in the same way as the standard kit units, so the upgrade stays focused on suspension behavior rather than a change in layout. Compatibility covers DT-03, DT-03T, DT-02, TT-02B and DF-02 chassis cars, which makes the set useful for repair, replacement or tuning across several established platforms. On a buggy or off-road build, that means a more settled response through bumps, jumps and rough sections where suspension consistency shapes how the chassis tracks and lands. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
DT-04 Carbon Damper Stay Set, RC tuning parts
300022094€29.79
The DT-04 Carbon Damper Stay Set adds a focused suspension upgrade to a DT-04 RC chassis with carbon fiber plates and dedicated mounting hardware. Multiple holes in the main stay and side plates create clear adjustment options for damper positions, supporting setup changes that suit different surfaces and driving styles. The set contains 1 long carbon fiber plate, 2 smaller support plates, 4 black ball studs, several screws in different lengths, 2 lock nuts with blue nylon inserts, and 2 metal washers. This combination forms a complete fitting set for the stay components rather than loose replacement pieces gathered from different packs. The carbon fiber construction keeps the parts thin and rigid, while the hole pattern allows measured changes to mounting locations. Ball studs and lock nuts support secure attachment at the specified points, and the washers help seat the hardware cleanly during installation. On a workbench, the parts layout is easy to sort before fitting, and on the chassis the stay set supports careful suspension tuning through hardware-backed position changes. It suits builders refining a DT-04 setup with a dedicated carbon fiber upgrade rather than a general cosmetic add-on. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
DT-04/03 D-Parts, spare parts set, suspension sprue
300004254€8.49
DT-04/03 D-Parts is a replacement sprue for the 58340 assembly group, supplied as 1 parts tree with multiple molded components kept together on the runner. The black injection-molded frame brings the needed D-section pieces into one clearly organized format for repair work, rebuilds or restoring an existing RC model to running condition. The layout shown on the sprue includes 2 large wishbone-style arms along with several smaller connectors, mounting blocks and a collar-shaped piece. Keeping the components attached to the runner helps preserve the full set until each section is cut free for use. Visible molded identifiers including D, 2, 3 and 4 provide a direct reference on the frame itself, which helps when sorting the pieces during maintenance. As a dedicated spare part rather than a universal accessory, this set is intended for the matching DT-04/03 application named in the data. On the workbench, the sprue supports targeted replacement after wear, impact or loss of an original section. It also fits rebuild sessions where a chassis needs fresh D-group components before the next run or display refresh.
Shock absorbers & springs
F103RS/GT-F104 Front Spring (3x4), model spare part
300050509€5.59
The F103RS/GT-F104 Front Spring (3x4) is a model spare part for front suspension service on a wide range of compatible Tamiya chassis. With 12 coil springs in the pack, it supports routine replacement work as well as keeping matching spares ready for setup changes between running sessions. This set is specified for F103RS/GT-F104 applications and is listed for F104PRO II, F104Ver.II PRO, F104W, F104, F103GT, RM-01, TRF103, TRF102 and TRF101. That broad compatibility makes it useful for hobby benches that support more than one chassis generation. The 3x4 spring format gives a clear reference point when replacing existing front suspension parts, helping maintain the intended configuration on the car. As a dedicated spare part rather than a general hardware assortment, it keeps maintenance focused on the exact area that needs attention. On a workshop bench, the 12-piece quantity is practical for regular upkeep, rebuilds and storing reserve parts alongside a race or practice setup. It also suits builders who maintain several compatible chassis and want one spring pack that can stay in rotation across different models. Warning! Not suitable for children under 14 years.
Axes & drive shafts
F104/F103 Special King Pin, model spare part
300053119€4.49
The F104/F103 Special King Pin is a dedicated spare part for compatible F104 and F103 chassis, intended for maintenance, repair and ongoing setup work. As a king pin, it belongs to the front suspension area where precise alignment between steering and suspension components matters during rebuilds and replacement work. This part is supplied for the F104/F103 platform rather than as a generic hardware piece, which helps keep servicing focused on the correct chassis family. It suits replacing a worn or damaged king pin during routine maintenance, or keeping a matching spare ready in workshop storage for future repairs. The compact format also fits neatly into parts boxes and bench organisers used for model upkeep, making it easier to separate chassis-specific hardware from general screws and fittings. On the workbench, the part supports clean, direct replacement when a front-end rebuild is needed after running sessions or inspection. It also fits tuning and restoration tasks where the original suspension layout of an F104 or F103 chassis needs the correct replacement component rather than an improvised substitute. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
GF-01 Alu. Oil Damper (4), RC damper set
300054670€62.49
The GF-01 Alu. Oil Damper set adds 4 aluminum oil dampers to GF-01 and WR-02 chassis cars, bringing more controlled suspension movement to rough ground and uneven running surfaces. Silver-finish cylinders with blue anodized caps and ends give the chassis a crisp mechanical look while introducing a functional oil-filled damping setup. The set is supplied as an aluminum oil pressure shock absorber set with 99 pieces, including the small attachment parts needed for mounting. The assembly documents show 3-hole pistons, damper shafts, rod guides, O-rings, spacers and ball connectors working together inside each cylinder to manage suspension travel. Front and rear damper builds differ by chassis position, with 2 dampers configured for the front and 2 for the rear. The included damper oil is specified as #400 in the assembly notes. Use with spring kit 53974 is stated in the data, and G6-01 or G6-01TR chassis require 6 dampers where that setup is used. Installed on a GF-01 or WR-02 model, the dampers support more composed running when the chassis crosses loose ground, bumps and broken surfaces. The color-contrasting hardware also stands out during workshop assembly and suspension tuning, where each cylinder, cap and end remains easy to identify at a glance. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
J Parts Fr. Damper Stay, model spare parts set
319115433€14.79
J Parts Fr. Damper Stay is a dedicated spare parts set for the 58618 Mt.Beetle and focuses on the front damper mounting section used in the chassis structure. The molded black components are supplied on a sprue frame, giving a clear overview of the shapes before cutting, test fitting and installation during a repair session. The set is suited to replacing worn, damaged or missing structural parts rather than improvising with unmatched hardware. Multiple mounting pieces and braces are formed as matching components, which helps maintain the intended geometry around the front suspension area. The sprue layout also helps with part identification at the bench, especially when several maintenance jobs are underway at once. Because this is a model spare parts set rather than a complete vehicle or kit, it fits naturally into regular workshop use alongside stored service parts for ongoing upkeep. On the work surface, the parts support a focused rebuild of the front end after heavy running or accidental damage. They also make sense as reserve stock for a 58618 Mt.Beetle build that is driven regularly and maintained over time, where having the correct front damper stay parts ready can shorten downtime between sessions. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
Leaf Spring A (4), model spare part for 58372
309808091€14.49
Leaf Spring A is a dedicated model spare part set for 58372, supplied as 4 matching spring strips in black metal. Each strip has a curved profile, rolled looped ends and 3 round mounting holes near the centre, giving the set the exact component form needed where this part group is missing, worn or due for replacement. The 4-piece pack supports maintenance and rebuild work with a consistent set of identical parts rather than mixed hardware. The metal strips are shaped for suspension-style or retaining-style installation within the matching model assembly, and the repeated hole pattern helps align the part with the existing mounting points on 58372. This makes the set useful for restoring the original mechanical layout of the designated model instead of adapting a generic strip or bracket. The compact spare part format also suits keeping a correct replacement set on hand for workshop storage. On the bench, the set fits naturally into repair sessions, part swaps and planned overhauls of 58372. It also works as a direct stock replacement when a rebuild calls for the exact Leaf Spring A component rather than an improvised alternative.
Shock absorbers & springs
Leaf Spring B, spare part set for 58372
309808092€8.29
Leaf Spring B is a dedicated spare part set for 58372 and supplies 4 matching replacement pieces for repair or maintenance work on the designated model. The set uses one clearly defined component type, making it suitable when the original leaf spring elements need to be exchanged rather than replacing a larger assembly. Each piece follows the same curved form shown in the reference image, with 3 round mounting holes positioned near the centre for attachment. That repeated geometry matters during maintenance because all 4 parts share the same layout and can be fitted as matching replacements within the same suspension area. The black finish keeps the appearance consistent with the pictured parts, while the compact format suits parts storage in a workshop drawer, spares box or model case between repair sessions. As a model spare part, this set is aimed at restoring the intended structure of 58372 with the correct designated component rather than adapting a generic substitute. The 4-piece format supports planned servicing as well as single-part replacement when a matching spare is needed on hand. On the bench, the identical hole pattern and arched profile help keep repair work focused on the exact section that needs attention on 58372. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
Leaf Spring, spare part set, 2-piece suspension pair
309808177€5.99
This leaf spring set supplies 2 replacement suspension parts for compatible model maintenance and repair work. Each piece is formed as a curved metal spring strip, creating the arched profile needed for a leaf spring layout and giving a clear mechanical role within the assembly. At the center of each spring, 3 round mounting holes provide the fastening area for installation to the matching structure. The ends are bent into looped hooks in opposite orientations, showing that the parts are made as a left and right mirrored pair rather than 2 identical strips. That mirrored construction matters when restoring the original suspension geometry on both sides of a vehicle. The black finish and compact shape also make the parts easy to identify among workshop spares during servicing. The set suits rebuilds, repairs, and parts replacement on a compatible model that uses this spring format. Whether a suspension assembly is being refreshed after wear or a stored build is being returned to running condition, these 2 springs provide the specific hardware needed for the job. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
Low Friction Damper V Parts, RC spare parts
300053334€7.29
Low Friction Damper V Parts supply the small running components that keep RC damper assemblies working smoothly across a wide range of Tamiya chassis. The set contains 2 V-part sprues with 22 pieces and covers damper ends, top ends, spring retainers, resin pistons and resin damper spacers for low-friction, ultra-low-friction and TRF dampers. This spare parts set is aimed at rebuild work, scheduled maintenance and replacing worn suspension internals without changing the full damper assembly. The dark gray molded parts arrive on sprues for clean identification during bench work. Compatibility reaches across touring, formula, buggy and rally platforms named in the data, including XV-01, TA06, FF-03, TT-02, M-07 CONCEPT, M-08 CONCEPT, F104, DB01 and TD4 chassis. Several applications require combination with matching damper sets such as 53571, 42273, 42355, 42102, 42354, 53901, 53926 or 54993 as specified in the data. On a workshop bench, these components help restore precise damper movement after wear in the original running parts. They also make a practical stock addition for regular chassis servicing, especially where multiple compatible Tamiya platforms are already in use. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
Lunch Box D-Parts, replacement parts set
309005230€16.99
The Lunch Box D-Parts set is a dedicated replacement parts pack for 58063, supplying molded components on sprues for repair, restoration, or planned maintenance. Black injection-molded pieces with formed mounting shapes and structural contours support accurate replacement work while keeping the original model configuration intact. The sprue layout keeps the individual parts grouped until they are cut free, which helps with part identification during bench work and reduces mix-ups between similar small components. Visible shapes in the set include bracket-style sections, circular adapter-like pieces, connector forms, and a larger reinforced panel with raised ribbing. That mix points to structural and mounting functions rather than decorative trim, making the set useful when worn, broken, or missing components need to be exchanged with matching replacements. The molded finish and defined edges also support clean alignment during fitting. On the workbench, this set suits rebuilds after heavy running, careful restoration of an older Lunch Box, or keeping spare components ready for future service. It also fits organized parts storage for hobby rooms where model-specific replacement sets help keep maintenance straightforward. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
MB-01 A-Parts Uprights, chassis parts set
300051719€7.19
This MB-01 A-Parts set brings several core chassis pieces together for focused maintenance on the MB-01 platform. The pack contains uprights, a gear cover, suspension mounts, a damper stay and hex hubs, giving rebuilds and repairs the matching parts needed for the correct locations within the chassis layout. The different components cover multiple mechanical jobs across the car. Uprights sit at the wheel ends and provide the mounting points around the axle area, while the hex hubs connect the wheel fitment to the drivetrain side. The gear cover closes off part of the transmission area, and the suspension mounts and damper stay support the placement of suspension and damping hardware on the chassis. Because these parts are supplied as A-Parts for the MB-01 chassis, the set suits replacement of worn pieces, accident damage or missing original components without mixing unrelated hardware. On the bench, this set supports anything from a single damaged corner repair to a broader chassis overhaul. It also works well as workshop stock for MB-01 owners who want the correct molded parts ready for routine service, rebuild planning or trackside maintenance between running sessions.
Shock absorbers & springs
O-Ring 3x6mm Red, RC spare part for dampers
300050597€3.39
This 10-piece pack of red O-rings in 3 x 6 mm format is made for damper and wheel axle use on selected RC chassis, giving a compact spare set for routine maintenance, worn seal replacement and parts-box stock. The small ring size suits jobs where a matching dimension matters, whether the work focuses on suspension service or axle-related fitting points. Compatibility is clearly defined across several chassis families. The O-rings can be used on TT-02, TT-02D and TT-02FT vehicles equipped with 50746, on TT-01 TYPE-E vehicles equipped with 53619, and on DT-03 or DT-03T vehicles equipped with 54567. TT-02RR lists this part as standard kit equipment. For DT-02, XB cannot be used, so chassis version and installed parts should be checked before fitting. In workshop use, a 10-pack keeps matching replacements ready for rebuilds, scheduled servicing or the correction of worn damper and axle seals after regular running sessions. The simple scope of delivery keeps the focus on the parts themselves: 10 O-rings for compatible RC maintenance tasks. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
Oil Damper VG O-Rings 30deg, damper parts
300042359€9.19
Oil Damper VG O-Rings 30deg are replacement damper parts made to keep oil dampers working with a clean, responsive feel. The 30deg specification is tuned to support strong initial response, which is especially useful when older seals have started to lose their original performance during repeated running. The set contains 8 O-rings in a navy blue finish for routine maintenance or a planned damper refresh across multiple units. Their high-spec construction is designed to minimize the amount of air forced into the dampers while the model is moving, helping the oil circuit stay more stable through longer sessions. That reduction in trapped air supports more even damping behavior instead of the less consistent action that can appear as seals wear. As a focused replacement part, this set suits regular workshop servicing as well as targeted tuning when damper response needs attention. During rebuilds, race-day maintenance, or general suspension servicing, a fresh set of O-rings can make a noticeable difference to how smoothly the dampers cycle. Keeping spare seals on hand also helps maintain a dependable setup between runs when worn internal parts need a direct replacement.
Shock absorbers & springs
On-Road Spring Set, tuning accessory, hard medium soft
300053163€21.29
This on-road spring set adds a wider suspension tuning range to compatible RC chassis with 6 springs in hard, medium and soft rates. The colour-coded finish in fluorescent red, fluorescent yellow and fluorescent blue makes each rate easy to identify during setup changes, helping keep adjustments organised between test sessions and repeat runs. The set is described as a softer spring kit than OP440, which opens another direction for chassis tuning when a setup calls for more compliant suspension response. It is intended for use across a broad group of platforms including F104PRO II, F104W, F104, F103GT, M-07 CONCEPT, M-06, M-06 PRO, M-05 ver.II PRO, M-05, M-05 PRO, MF-01X, TT-02FT, TT-02RR, TT-02D, TT-02 and TT-01 TYPE-E. For F104 and F104W chassis, the data specifies use with 53901. On the workbench, the 3 spring rates support direct comparison of suspension behaviour during circuit setup, whether the focus is front-end response, overall balance or matching the chassis to track conditions. Scope of delivery: 6x springs hard, medium, soft. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
Silicone Damper Oil Hard Set, RC oil, #800/900/1000
300053445€20.991 l = €349.83
The Silicone Damper Oil Hard Set brings firmer suspension tuning to RC maintenance with 3 silicone-based oils in grades #800, #900 and #1000. Each bottle contains 20 cc, and the pointed applicator nozzle helps guide the fluid into compact damper bodies with controlled dispensing during rebuilds or setup work. This set is intended for oil pressure dampers and is tailored to Tamiya applications where damping changes are part of chassis adjustment. Higher viscosity means thicker oil and a harder damping feel, so the three grades in this set give a practical range for comparing response and refining how a model settles through corners, braking zones and uneven sections. The bottles are colour coded as pink, clear and light blue, making the three viscosities easier to distinguish on the bench. The fluid is identified for shock absorber use on model vehicles, and the set can also extend the available tuning range when combined with the softer companion sets in the same series. Compatibility listed in the data covers CC-01, F103GT, TB-03 and TB-03 VDS chassis. That makes the set a useful workshop supply for regular servicing, seasonal retuning or keeping several RC builds ready with different damper fills for changing surfaces and handling preferences. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
Silicone Damper Oil Medium Set #500 #600 #700
300053444€20.991 l = €349.83
This silicone damper oil medium set brings 3 tuning grades together for model vehicle shock absorbers: #500, #600 and #700. The three 20 cc bottles cover the medium range in Tamiya's viscosity system, where a lower number indicates a lower viscosity and a higher number indicates a thicker oil, making step-by-step suspension changes easier to plan at the workbench. The set is intended for model vehicles and uses silicone-based oil in 3 colour-coded grades: green #500, blue #600 and purple #700. At 25 °C, the kinematic viscosities are 500 mm2/s, 600 mm2/s and 700 mm2/s. This spacing supports direct comparison between nearby setups instead of forcing a large jump in damping feel. The pointed bottle tips support controlled dispensing into damper bodies during filling, topping up or rebuild work, and the 20 cc fill quantity on each bottle gives enough material for repeated service sessions. On an RC chassis, these 3 grades can be used when refining how quickly the suspension moves over bumps, settles after compression or reacts to changing grip levels. The set suits routine maintenance as well as test sessions where several oil weights are compared back to back on the same model vehicle.
Shock absorbers & springs
Silicone Damper Oil Soft Set, RC model accessory
300053443€20.991 l = €349.83
This silicone damper oil soft set brings suspension tuning into a clearly graded format with 3 bottles covering #200, #300 and #400 viscosities. The softer range supports fine adjustment of oil-filled dampers on RC model vehicles, whether the goal is a lighter response over uneven sections or a more measured starting point for chassis setup at the workbench. Each bottle contains 20 cc and uses a narrow nozzle that helps guide the fluid into damper bodies with controlled application. The set is identified by red, orange and yellow oils, making the grades easy to separate during rebuilds, refills and comparison testing. The formula is silicone-based and intended for model vehicle shock absorber use. Tamiya's viscosity system follows a simple rule: lower numbers indicate lower viscosity, while higher numbers indicate thicker oil. This soft set can also extend its adjustment range when used together with the medium and hard sets in the same series. Compatible applications named in the data include the GB-01S chassis, CC-01 chassis, F103GT chassis, TB-03 chassis and TB-03 VDS chassis. On a tuning bench, the 3 grades allow direct back-to-back damper changes between runs or during a rebuild, with each step in viscosity offering a clear reference point for suspension experimentation. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
Silicone Diff. Oil #3.000, model supply, 40cc
300054657€9.391 l = €234.75
Silicone Diff. Oil #3.000 is a model supply for tuning oil-filled sealed differential units and roll dampers in R/C cars. The 40cc bottle and narrow nozzle suit careful, repeatable application at the bench when a setup calls for a 3000 weight fluid on faster layouts with long, sweeping turns. The fluid is identified in the technical data as polydimethylsiloxane, with a kinematic viscosity of 3,000 mm2/s at 25 °C. It is a liquid, odourless and insoluble in water, with a relative density of 0.97 at 25 °C. That specification gives a clear reference point when matching maintenance supplies to an existing differential fill or a planned roll damper setup. The bottle format keeps the quantity compact for workshop storage while still covering repeated servicing across compatible R/C car drivetrains. In use, the oil suits rebuilds of sealed differentials after cleaning, routine setup changes between track conditions, or roll damper servicing on formula and RM chassis. On a pit table or home workbench, the 40cc fill offers a practical amount for keeping one viscosity grade ready for regular tuning work. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
Silicone Diff. Oil #4000, differential oil, 40cc
300022006€8.991 l = €224.75
Silicone Diff. Oil #4000 is a tuning fluid for oil gear differentials that brings a clear handling change to model vehicles. The high-viscosity grade is intended to support stable, speedy cornering in the high-speed range, making it a useful choice when differential action needs a firmer setup on faster sections. The bottle contains 40cc of yellow silicone oil and is sized for about 22 uses in touring car different gears. Its bottle format with dispensing nozzle supports measured application during maintenance, refills, or setup changes at the bench. The fluid is identified as #4000 viscosity, and the supplied data lists a kinematic viscosity of 4,000 mm2/s at 25 °C. This Hop-Up Option is intended specifically for model vehicle differentials that use oil as part of their tuning setup. On indoor tracks, club circuits, or home workshop setups, the oil can be used to compare differential feel against lower-viscosity grades and refine how the car responds through faster corners. It suits repeated testing sessions where small setup changes matter, while the 40cc volume keeps enough fluid on hand for ongoing drivetrain maintenance.
Shock absorbers & springs
TA-/TB-/TRF Urethane Front Bumper RC Part
300054145€4.59
The TA-/TB-/TRF Urethane Front Bumper is a chassis tuning part for selected Tamiya on-road platforms, using a larger-than-standard bumper profile to reduce the gap between chassis and bodyshell. That closer fit helps suppress body shimmy during high-speed running, giving the shell steadier support at the front of the car. The part is supplied as 1 foam rammer and is shaped as a curved bumper insert with 2 mounting holes and edge cut-outs for installation on compatible layouts. Supported chassis named in the data include TA07 MS Chassis, TA07 PRO Chassis, TA05 ver.II Chassis, TB-Evo.7 Chassis, TB-Evo.6 MS Chassis, TB-Evo.6 Chassis, TB-05 PRO Chassis, TB-04 Chassis, TB-04 PRO Chassis, TB-03 chassis, TB-03 VDS Chassis, TRF419XR Chassis, TRF419X Chassis and TRF419Chassis. As a front-end setup part, it focuses on shell support rather than decoration, making it relevant where close body fit and controlled movement matter on faster laps. It suits rebuilds, maintenance and setup changes on compatible touring chassis already in use. During track preparation, the larger bumper profile can be fitted when a closer bodyshell position is needed at the nose of the car for more settled running at speed. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
TAMIYA Silicone Oil #400, damper oil, 40 ml
300054710€8.191 l = €204.75
TAMIYA Silicone Oil #400 is a 40 ml damper oil for model vehicles, made to tune the feel of oil-filled dampers with a simple viscosity change. The #400 grade sits in the firmer range, since higher numbers indicate a harder viscosity, making it a practical choice when suspension setup needs a more controlled response. The bottle uses a narrow dispensing tip that supports careful, drop-by-drop application when filling shock bodies on the workbench. Its larger 40 ml content is aimed at frequent users and offers more oil than the earlier 35 ml and 20 ml bottles referenced in previous sets. Each viscosity grade in the range has its own color coding, which helps keep different oils clearly sorted in a toolbox during maintenance sessions. The supplied safety data identifies the mixture as organopolysiloxanes and lists its intended use as damper oil for model vehicles. On a setup bench, Silicone Oil #400 fits routine shock servicing, viscosity swaps between runs, and fine suspension adjustment when track conditions or handling balance call for a firmer damper fill. It also suits keeping several grades organized side by side, so the selected oil can be identified quickly before the next rebuild or test session.
Shock absorbers & springs
TD2/TD4 Alum. BigBore Rear Damper, RC parts set
300054505€88.99
The TD2/TD4 Alum. BigBore Rear Damper set brings a larger aluminum oil damper layout to the rear suspension, with 2 dampers built around threaded bodies, 40.7 mm piston rods and a full set of internal sealing parts. During assembly, the piston is filled with damper oil and moved slowly through the cylinder to release trapped air, giving the aeration design its working basis before the cap is secured. Inside each damper, the build uses O-rings in 2 mm, 3 mm, 6.5 mm, 11.5 mm and 14 mm sizes, plus 4 x 0.1 mm and 3 x 0.2 mm shims to support sealing and internal spacing. Two piston types are provided, with 1.6 mm and 1.7 mm holes, so the oil flow setup can be chosen during the build rather than fixed to one specification. Spacers are used to adjust rebound stroke and damper attachment position, adding another layer of chassis setup detail. Spring retainers and spring adjusters complete the upper section, while screws in 3 x 18 mm, 3 x 15 mm and 3 x 12 mm sizes support mounting. On the bench, this set suits careful suspension rebuilding, oil filling and setup changes between running sessions. Damper oil and coil springs are separately available, and the assembled dampers are intended for TD2 and TD4 rear suspension use. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
Touring Car Bumper Sponge, RC accessory, grey
300053415€5.79
This touring car bumper sponge is a grey urethane block sized at 70 x 225 x 25 mm, made to be trimmed into a custom front bumper for RC chassis. The soft material is intended to absorb shocks from contact and falls, helping protect the body shell and chassis when the front end takes an impact. Instead of using a fixed shape, the block can be cut to suit the body mounted on the car. That makes it possible to match the bumper more closely to the shell profile and use the available space at the nose section more effectively. The universal fit information covers a broad list of compatible chassis, including F103GT, FF-04 EVO, FF-03, FF-03 PRO, TA08 PRO, TA07 MS, TA07 PRO, TA06 MS, TA06, TA06 PRO, TA05 Ver.II, TB-Evo.7, TB-Evo.6 MS, TB-Evo.6, TB-05 PRO, TB-04, TB-04 PRO, TB-03, TB-03 VDS, TRF419XR, TRF419X and TRF419. In workshop use, the sponge can be shaped for a new shell, a replacement body or a revised race setup where front-end clearance matters. The rectangular format also leaves room to remove only as much material as the body line requires, rather than working around a pre-formed bumper shape. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
Touring Car Tuned Spring Short, chassis spring set
300053333€21.29
The Touring Car Tuned Spring Short set adds a focused suspension tuning option for compatible on-road chassis. With 6 springs in the pack and 3 distinct rates, it supports more precise handling changes than a single-rate replacement and keeps setup work clear through fluorescent color coding. The set contains 2 soft, 2 medium and 2 hard short springs, so front and rear combinations can be matched without mixing rates. Soft springs are marked in fluorescent red, medium in fluorescent yellow and hard in fluorescent blue, making each pair easy to identify during setup changes. The short format covers about half the gap between OP163 and OP440, which adds a useful intermediate step when refining corner response and chassis balance. Compatibility is stated for M-08 CONCEPT, M-07 CONCEPT, M-06, M-06 PRO, M-05 ver.II PRO, M-05, M-05 PRO and MF-01X chassis. At the workbench, the 3-rate layout helps compare suspension changes methodically instead of swapping between wider setup steps. On a running chassis, the paired springs support consistent front or rear installation while leaving room to test different combinations across multiple sessions. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
TRF Damper Urethane Bushings, RC Damper Parts
300053577€4.79
The TRF Damper Urethane Bush set supplies 10 replacement bushings for servicing compatible TRF dampers. Used as oil seals, these urethane parts help keep the damper sealed correctly so suspension action stays consistent and maintenance can be carried out before visible wear affects performance. The set is intended for TRF dampers with fluorine coating specification and supports regular rebuild work on a wide range of chassis. Compatibility includes XV-01, XV-01T, XV-01 PRO, TB-03, TT-02, TT-02D, TT-02 TYPE-S, TT-02 TYPE-SR, TT-01 TYPE-E, TT-01D TYPE-E, TT-02RR and TT-02FT when used with 53571. It also fits M-07 CONCEPT chassis when used with 42102, 42273, 42355 or 54000. The scope of delivery contains 10 urethane bushings. In workshop use, fresh seals can be fitted during damper maintenance to restore the intended sealing function and keep the suspension ready for further track sessions. The compact pack format also makes it easy to keep matching service parts on hand for planned rebuilds or routine upkeep across compatible chassis. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
TRF Dampers Reinforced V Parts, damper upgrade set
300054871€8.19
Reinforced V Parts for TRF Dampers update the standard mounting and spring support pieces with redesigned shapes and material, opening up more setup options for suspension tuning. The set is built around TRF damper maintenance and adjustment, so worn parts can be replaced while the damper layout is matched more closely to the chassis setup in use. Inside the set are 5 mm damper ends in S and M, 5.8 mm damper ends in S and M, 5 mm damper tops, 5.8 mm damper tops, and spring retainers in S and M. The instruction data notes that parts are chosen according to damper length, and one spring retainer version is specified for large diameter springs. One step requires a 1 mm hole as shown in the technical diagram, and the ball connector is pressed in from the indicated side on the relevant parts. For use with V2, V3 and V7, separately sold dedicated 5.8 mm damper ball connector nuts and a cylinder cap are required. This set suits routine damper overhauls, chassis retuning between runs, and replacing standard TRF damper parts with reinforced alternatives. It is compatible with TRF Dampers such as Items 53571, 53901 and 54000 when used with Item 53334, making it a focused upgrade for established TRF suspension setups. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
TRF VG O-Ring Damper Grease, model supply, 3 g
300042129€16.191 kg = €5,396.67
TRF VG O-Ring Damper Grease is a dedicated model supply for damper maintenance, developed to support smooth sliding action and a cleaner seal at the O-rings. The blue grease comes in a 3 g case, making it easy to keep with regular bench supplies for suspension service. Its role is specific: the grease is intended for damper use rather than broad workshop application. When applied at the O-rings, it helps the damper move with less drag while also helping to prevent oil leaks. That combination matters during rebuilds and routine maintenance, where seal condition and controlled movement both affect how a shock unit works. The compact format also suits toolboxes, parts drawers and pit setups where small consumables need to stay easy to find. On a workbench, in a pit bag or beside a set of shock parts during servicing, this grease fits naturally into RC maintenance routines. It supports careful damper preparation for fresh builds, rebuilds and seal replacement, with a clearly defined use that keeps suspension work focused and tidy. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
TRF421 Damper Oil Seals, model spare parts
300051738€4.39
The TRF421 Damper Oil Seals are spare parts made for the damper system on the TRF421. Supplied as a 4-piece set, they provide the key sealing parts needed when servicing compatible dampers and refreshing worn internal components. Inside a damper, the oil seal sits at a critical point where smooth shaft movement and oil retention need to work together. Replacing used seals can help restore the damper's intended function during maintenance, especially when rebuilding shocks after repeated running sessions. The 4 matching pieces make sense for work across a complete set of dampers, keeping the rebuild consistent from corner to corner. As compact workshop parts, they fit naturally into routine chassis care alongside cleaning, inspection and fresh damper oil. On the bench, these seals suit planned rebuilds as well as targeted repairs when a damper needs attention. For TRF421 owners who keep setup changes and servicing close under control, having the correct oil seals on hand supports a more orderly maintenance routine. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
TRF421 Damper Parts, RC spare parts set
300051743€5.69
TRF421 Damper Parts are a dedicated RC spare parts set for the damper area of the TRF421 platform. The pack brings together black molded components such as eyelet-style connectors, ring-shaped mounts and slotted retaining pieces that support attachment, pivoting and secure placement within the suspension assembly. These parts are suited to maintenance work where small connection points have worn, gone missing or need replacement after heavy running. The eyelet forms are designed for linkage-style mounting, while the clip and ring elements handle locating and retaining tasks around the damper hardware. Using model-specific replacement parts helps preserve the intended fit of the assembly and keeps service work focused on the exact section that needs attention. On the workbench, the set supports routine rebuilds, race-day spares management and targeted repairs without replacing larger assemblies unnecessarily. It fits naturally into a parts box for ongoing chassis upkeep, especially when several small connectors are best renewed together to return the suspension area to proper working order. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
TRF421X Carb. Bumper Holder 2mm, model part
313404179€17.99
The TRF421X Carb. Bumper Holder 2mm is a dedicated model part for the front end of a compatible chassis build. Its carbon construction and 2 mm specification give builders a clearly defined replacement or upgrade component when the bumper mounting area needs a matching plate. As a bumper holder, this part is shaped for a specific mechanical role rather than general use. The flat carbon format suits setups where low weight and exact material choice matter, and the stated 2 mm thickness helps when comparing an installed part against a fresh replacement. In workshop use, that clear specification can save time during maintenance because the part can be matched directly to the required position. The TRF421X designation also keeps the component tied to its intended platform instead of a broad universal fit claim. This part fits naturally into repair sessions, race-day spares planning, or a careful chassis refresh between runs. On the bench, it supports a straightforward parts check for the front bumper mounting area and helps keep a competition-focused build consistent with its existing setup. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
TRF421X Damper Cylinder, model spare part
319803495€38.99
The TRF421X Damper Cylinder set provides 2 replacement cylinders for damper service on compatible Tamiya model applications. As a dedicated suspension spare part, it supports precise maintenance work where the original cylinder bodies need to be renewed to keep a shock unit properly assembled. Each cylinder is intended for damper rebuild and repair tasks rather than general-purpose use. The 2-piece count suits paired shock work, so both sides of an axle setup can be refreshed in one service step when matching parts are required. In a tuning bench or repair area, a dedicated cylinder set also helps keep parts selection focused on the exact suspension section being rebuilt. Batteries are not included. This spare part fits naturally into routine workshop use, whether a chassis is being stripped for maintenance or a damper set is being rebuilt after repeated running sessions. It also works well as a shelf spare for model owners who keep key suspension components ready for future service intervals. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
TRF421X Front Damper Stay Mount, model spare part
313451584€19.69
The TRF421X Front Damper Stay Mount is a blue model spare part made for front-end chassis service and replacement work. Its dedicated form focuses on the damper stay mounting area, making it a direct choice when that specific fixing point needs renewal during maintenance or a rebuild. Used as a separate replacement component rather than a full assembly, this mount helps keep repair work concentrated on the exact section that has worn, been damaged or is being updated. The blue colour also helps with quick visual identification among other workshop parts during sorting, fitting and inspection. The product data confirms that batteries are not included, which fits its role as a non-powered chassis component rather than an electronic unit. No operating voltage, runtime or speed figure applies here, because this part serves a structural mounting function within a model setup. On the workbench, the mount suits routine chassis upkeep, front-end refreshes and spare-parts storage between running sessions. It also fits planned rebuilds where a dedicated front damper stay mount is needed to restore the intended layout with a matching replacement part. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
TRF421X Rear Damper Stay Mount, model spare part
313451585€19.69
The TRF421X Rear Damper Stay Mount is a blue spare part for model maintenance, rebuilds and targeted replacement work. Its role is specific and functional: it provides the mounting point for the rear damper stay area, so a compatible chassis can be restored with the intended component rather than a makeshift substitute. Used during servicing, the mount helps return the rear suspension section to its proper attachment layout. The blue finish gives the part quick visual recognition on the workbench and in storage trays, which is useful when sorting hardware for a rebuild or preparing replacement parts before installation. As a dedicated spare part rather than a universal fitting, it is best matched to the TRF421X designation named in the part title. This kind of component fits naturally into routine chassis upkeep, whether replacing a worn mount after running sessions or keeping a fresh part ready in the spares collection. In a workshop setting, it supports cleaner maintenance planning by keeping the rear damper mounting area equipped with the correct replacement piece.
Shock absorbers & springs
TT-01 Urethane Bumper M, chassis spare part
300051007€6.29
The TT-01 Urethane Bumper M is a chassis spare part for selected Tamiya on-road platforms, built around a urethane foam body that sits as the specified impact element on compatible assemblies. Its M-size format and simple plate shape make it a focused replacement choice when an existing bumper insert has worn down, compressed or needs to be renewed during routine maintenance. The part is supplied as 1 urethane foam bumper and is intended for TT-02RR, TT-02D, TT-02 TYPE-SR, TT-02 TYPE-S, TT-02 and TT-01 TYPE-E chassis. The component uses an elongated form with rounded corners and 2 oval mounting holes, a layout that matches the mounting points shown for this spare part and supports straightforward positioning on the relevant chassis area. As a dedicated replacement rather than a universal pad, it helps keep a build aligned with the exact platform list given in the technical data. This kind of spare part fits naturally into rebuilds after track contact, scheduled servicing between runs, or a fresh chassis setup where worn foam has lost its original form. On a parts bench or in a pit box, the single-piece delivery keeps the replacement clear and specific for the supported TT series platforms. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
TT-01/TGS Urethane Bumper, chassis spare part
300051019€5.99
The TT-01/TGS Urethane Bumper is a dedicated chassis spare part for selected Tamiya platforms, using a die-cut urethane foam shape to match the front-end layout of compatible models. Its tapered form and 2 oval cut-outs point to a defined mounting position, which matters when a worn or compressed bumper needs to be replaced with the correct part rather than trimmed from generic foam. Compatibility is stated for TT-02RR, TT-02D, TT-02 TYPE-SR, TT-02 TYPE-S, TT-02 and TT-01 TYPE-E chassis. The scope of delivery contains 1 urethane bumper. The foam construction gives this part the compressible structure expected from a bumper insert, while the elongated profile and rounded ends align with the narrow front section commonly used on these chassis families. As a model accessory rather than a complete kit, it is intended for maintenance, repair, or parts replacement on an existing build. This spare fits naturally into workshop tasks such as replacing an older front foam piece during a chassis refresh or keeping a correct backup part ready between running sessions. For collectors and drivers maintaining a compatible platform, a chassis-specific bumper keeps the parts choice focused and avoids guesswork during servicing. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
TT-02 Oil Gear Diff Unit, RC drivetrain upgrade
300054875€37.99
The TT-02 Oil Gear Diff Unit brings an oil-filled differential setup to the TT-02 series, replacing the standard differential gear with a drivetrain assembly that supports smooth, efficient power transfer. Inside the unit, die-cast bevel gears work within a glass fiber-reinforced nylon gear case, while the gasket helps seal the housing for oil-filled operation. Setup changes can be made by selecting different oil grades or gear diff putty, which alters how the differential reacts as the chassis loads and unloads through turns. The assembly uses a ring gear, bevel pinion gear, O-rings, shafts and ball bearings to route drive through the gearbox joints with controlled internal movement. The instruction data specifies that oil should be filled only to the level of the differential axle, and the housing screws are tightened little by little in sequence to help prevent leaks. The included bevel pinion gear is used for the conversion, and the unit is not compatible with standard plastic drive shafts. Assembly universal shafts are used instead. This Hop-Up Option suits maintenance, rebuild and tuning work on TT-02 based RC cars where drivetrain response is part of the setup process. Compatible TT-02 series chassis can be equipped with the unit using the required matching parts for TT-02, TT-02D or TT02B applications. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
TT-02B Damper Stay, RC spare parts, front rear
319000562€11.79
This TT-02B A-Parts set provides front and rear damper stays as replacement components for the TT-02B platform. The black molded parts arrive on a single sprue, making the individual sections easy to identify before removal and helping keep workshop handling orderly during repair or rebuild work. The damper stay is a key suspension mounting section, as it carries the attachment points for the dampers and helps position them correctly on the chassis. Replacing a worn or damaged stay can restore the intended mounting layout and bring the front and rear suspension back into proper alignment with the rest of the build. The connected runner format also helps keep smaller sections together until the moment they are needed. This is especially useful when several maintenance steps happen at once and parts need to stay sorted. On a bench setup, these replacement pieces suit routine servicing after heavy running, collision damage, or a full chassis refresh. They also fit neatly into a spares box for ongoing TT-02B upkeep, where having the correct front and rear damper stays ready can shorten downtime between rebuild sessions. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
TT01D/R/E Urethane Bumper, chassis spare part
300051218€4.79
The TT01D/R/E Urethane Bumper is a grey chassis spare part made for front-end replacement on compatible Tamiya on-road platforms. Its urethane foam construction sits at the nose section of the chassis, where this component forms part of the front bumper area and restores the intended layout during repair or routine maintenance. This spare part is listed for the TT-01 Series and also fits TT-02RR, TT-02D, TT-02 TYPE-SR, TT-02 TYPE-S, TT-02, TT-01D TYPE-E and TT-01 TYPE-E chassis. The set contains 1 urethane foam bumper, making it a focused replacement for a worn, compressed or missing original part rather than a mixed hardware pack. The grey finish matches the stated version, and the single-part format keeps parts selection clear when servicing several compatible chassis types. It suits rebuilds after repeated running sessions, front-end refresh work, or keeping a bench stock of key wear parts for supported platforms. In a workshop setup with multiple TT-01 and TT-02 variants, the shared fitment helps streamline maintenance planning across the compatible chassis range. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
TT01E/R/D A-Parts, RC spare parts set, 13 pieces
300051318€7.19
This A-Parts set is made for TT-01D TYPE-E and TT-01 TYPE-E chassis and groups damper stay and gearbox frame components into one defined replacement pack. With 13 pieces in the set, it gives a direct way to service specific structural areas of a compatible RC model rather than searching across mixed hardware. The parts group suits maintenance work where the original mounting sections need renewal after wear, damage or a rebuild. Because the set is assigned to named TYPE-E variants, compatibility stays tied to the chassis family stated in the data. The scope of delivery contains 1x A-Parts set, which keeps the contents focused on this single component group. As a spare parts accessory in the Models & Accessories range, it fits naturally into bench stock for regular upkeep of an existing TT-01 platform. In workshop use, the set can be kept on hand for planned servicing or used when a damaged frame section interrupts running time. It also supports tidy restoration work on a compatible chassis where the goal is to return the original layout with the correct A-Parts group. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
Urethane Bumper M Blue, chassis bumper, 15 mm
300053683€7.19
The Urethane Bumper M Blue is a chassis bumper for selected Tamiya touring car platforms, combining 15 mm urethane thickness with a light blue finish that stands out from the standard grey version. Mounted at the front of the chassis, the bumper forms a compressible contact zone that helps manage knocks during RC driving while giving the build a more individual appearance. Compatible chassis listed in the data are TT-02RR, TT-02D, TT-02 TYPE-SR, TT-02 TYPE-S, TT-02 and TT-01 TYPE-E. The urethane material keeps the part lightweight, which suits tuning setups where unnecessary front-end mass is best avoided. The blue colour also pairs visually with the OP682 aluminum bumper when that part is used, creating a coordinated custom look across the front section. The scope of delivery contains 1 bumper. This part suits rebuilds, replacement work and visual updates on existing chassis. It can be fitted when refreshing a used front end, when matching blue option parts across a build, or when preparing a chassis for regular circuit sessions where a foam bumper remains a core contact component. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
V-Parts V1-11, RC spare parts set, C.V.A-Mini II
300050598€7.69
V-Parts V1-11 C.V.A-Mini II is a chassis-specific spare parts set for selected Tamiya model vehicle platforms. The set contains 2 sprues with molded components arranged for replacement work, helping restore the intended fit of assemblies that use this parts group in compatible builds. The fitment list is the key detail here. The set can be used with TT-02, TT-02D, TT-02RR and TT-02FT chassis, and also with vehicles equipped with 50746. It also fits TT-01 TYPE-E vehicles equipped with 53619. Further compatibility covers DT-03 and DT-03T vehicles equipped with 54567, plus the DN-01 chassis. DT-02 XB cannot be used, and on DN-01 the set cannot be combined with 54028. That makes this set useful for planned maintenance, replacing damaged molded parts, or keeping an existing chassis configuration consistent with the required option setup. On the bench, the 2-sprue format makes it easier to identify the molded parts group before installation and compare the frames with the existing assembly. For workshop stock, rebuilds or chassis servicing, this set supports direct parts replacement within the stated compatibility range. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
WT-01/TL-01B C-Parts, suspension parts set
300005688€14.49
This C-Parts suspension set is made for WT-01 and TL-01B chassis and provides a focused spare-parts solution for repairs, rebuilds and routine workshop maintenance. The black injection-molded sprue holds the components in their original runner layout, making it easier to match each shape to the required position before cutting and fitting the parts into the chassis. The set centers on suspension-related pieces rather than general hardware, with multiple arm forms, mounting elements, ring-style pieces and a larger curved section visible on the frame. Molded part markings such as 12, 13, 15 and 20 support identification during the build or repair process, while smaller numbered and lettered references on the runner help distinguish neighboring pieces. This kind of layout is especially useful when replacing damaged components after running sessions or when restoring an older chassis to working order. On the bench, the sprue format keeps the parts together until they are needed, which helps maintain order during staged repairs. For hobby storage, it also makes this set practical as a model-specific replacement kept alongside compatible WT-01 or TL-01B chassis parts for future servicing.
Shock absorbers & springs
XL Urethane Bumper, RC chassis part for TT-02
300054819€4.39
This XL urethane bumper adds a larger front impact buffer to TT-02 and TT-01 Type-E chassis cars while staying easy to adapt to different bodyshell shapes. The black urethane construction differs from the grey bumpers found on many on-road RC kits, giving this part a distinct look and a generous block of material for custom trimming. The bumper is supplied as 1 black urethane piece and is intended to be cut down to the size needed for the chassis and body combination in use. That cut-to-fit format helps align the foam more closely with the nose section of a touring car bodyshell, where contact in close running can mark or crack the shell. Instead of a fixed outline, the extra-large shape leaves room to remove only the material required for clearance around posts, mounts or body contours. As a chassis part, it focuses on front-end protection rather than styling changes. It suits workshop use when replacing a worn bumper, preparing a fresh bodyshell or setting up a different shell on an existing TT-02 or TT-01 Type-E platform. On indoor tracks, car parks or other smooth on-road running areas, the added urethane buffer helps take the edge off light contact before it reaches the bodyshell.