Other spare parts & accessories
Are you looking for special spare parts? Then browse through our extensive selection of Tamiya spare parts & accessories and find exactly what you need!
Other spare parts & accessories
Are you looking for special spare parts? Then browse through our extensive selection of Tamiya spare parts & accessories and find exactly what you need!
More
Other spare parts & accessories
10mm Shim Set, RC accessory, 0.1-0.3 mm spacers
300053588€13.49
This 10 mm shim set brings fine mechanical adjustment to RC chassis work, with 30 spacers sized at 10 mm inner diameter and 13 mm outer diameter for controlled spacing at shaft mounting points. The 3 thickness options of 0.1 mm, 0.2 mm and 0.3 mm make it possible to correct small gaps that can lead to unwanted movement in suspension or wheel axle assemblies. Instead of relying on a single washer size, the set gives stepped tuning options that suit different setup needs across on-road and off-road vehicles. Each shim can be placed to shift the position of a mounted part in small increments, including forward adjustment where the chassis layout calls for tighter spacing. That makes the set useful during maintenance, rebuilds and race-focused setup changes where alignment and reduced slippage matter. Scope of delivery: 1 spacer set with 30 pieces. On the bench, the assortment supports careful fitting of moving parts before a run. During a rebuild or handling-focused setup session, the different shim thicknesses help dial in cleaner spacing at the exact point where play needs to be reduced. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
1150 Ball Bearing Set, RC bearing pack, sealed
300053008€36.29
The 1150 Ball Bearing set brings a direct drivetrain upgrade to compatible RC chassis by replacing plain rotating points with sealed ball bearings. Each bearing uses rubber-covered sides and an 11 mm outer diameter, 5 mm inner diameter and 4 mm width, creating a compact format for hubs, axles and other moving assemblies where clean rotation matters. Installing ball bearings is a common first step when tuning running performance because they reduce drive loss and support smoother movement through the transmission. The sealed construction adds high dust resistance, which helps the bearings keep turning freely in regular road, buggy and track use. The pack includes 4 bearings for targeted replacement or routine maintenance on frequently used assemblies. Compatibility covers a broad list of chassis, including TD4, TD2, DF-02, DF-03, DT-02, DT-03, DT-03T, TT-02, TT-02B, TT-02D, TT-02RR, TT-02 TYPE-S, TT-02 TYPE-SR, TT-02FT, TT-01D TYPE-E, TT-01 TYPE-E, M-05, M-05 PRO, M-06, M-06 PRO, M-07 CONCEPT, M-08 CONCEPT, MF-01X, RM-01, TB-04, TB-04 PRO, TRF101, TRF102, TRF103, F103GT and F104 Ver.II PRO. On a workshop bench, the 4-piece set suits regular servicing before the next run or a focused upgrade on a fresh chassis build. Once fitted, the bearings support freer rotation in the moving parts that shape how efficiently the model puts power down. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
2mm C-Ring-Set, model accessory, 8-piece
300084171€2.19
This 2 mm C-Ring-Set supplies 8 matching retaining clips for model maintenance, repair work and parts replacement. The compact format suits assemblies that use small fastening points, where a C-shaped ring locks into a groove on a shaft or similar mounting point to hold parts in position. The set groups identical metal clips together, which helps when a rebuild calls for consistent replacement parts rather than mixed hardware. The open centre cutout allows each ring to snap into place on the intended fitting, making this type of fastener useful wherever a low-profile retainer is needed in a mechanical model assembly. The silver-coloured finish also makes the pieces easy to identify in a parts tray or workshop setup alongside screws, washers and other small hardware. Used as spare parts, these C-rings support routine servicing, careful restoration work and the replacement of missing retainers in existing builds. Kept in a hobby drawer, the 8-piece pack provides a practical stock of matching clips for future workshop tasks on compatible model mechanisms. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
2mm E-Ring Satz, model accessory, 15 pieces
300050588€3.09
This E-Ring Satz provides 15 matching retaining clips in a 2 mm size for model maintenance, repairs and mechanical assembly work. Each E-ring is made as a small stamped metal fastener that presses onto a grooved shaft or axle from the side, where it acts as a stop to hold mounted parts in place. The flat clip profile keeps the fastening point compact, which is useful in tight spaces around driveline and wheel assemblies. The pack suits jobs where worn or missing retaining hardware needs a direct replacement in the correct size. A 2 mm E-ring can be used wherever the assembly calls for this specification, including axle or shaft setups that carry gears, bushings or wheels. The 2 mm thickness stated in the data adds a clear reference point when matching spare hardware to an existing build. With 15 identical pieces in one set, the supply supports repeated service work and keeps consistent hardware ready for future rebuilds. On the workbench, these clips fit naturally into parts sorting trays, spare hardware boxes and routine maintenance kits for RC and scale model projects. They are especially useful when a rebuild calls for several matching retainers across multiple connection points or when a small clip needs quick replacement after disassembly. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
3mm 5.5x5.0mm Spacer, model accessory, 10-pack
319804641€8.19
This spacer set is built around exact measurements that matter during model maintenance and parts replacement. Each piece is specified at 3 mm with 5.5 x 5.0 mm dimensions, giving a clear reference for assemblies that rely on this format to maintain the intended spacing between compatible components. The set contains 10 matching spacers, which supports repeated service work without mixing different sizes in the same build. The defined dimensions make this set useful when an existing assembly already calls for 3 mm spacers and when consistent fit across several mounting points is needed. Rather than relying on approximate sizing, the stated 5.5 x 5.0 mm format gives a direct basis for checking compatibility against the parts already in use. On the workbench, these spacers suit routine maintenance, measured replacement and keeping spare hardware ready for future adjustments. The 10-piece count also helps when several identical positions in one assembly need the same spacer size, or when matching replacements are kept in reserve for later servicing. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
3mm O-Ring black, model accessory, 10-piece
300084195€1.99
This 10-piece pack of black 3 mm O-rings adds a practical spare-parts supply for model maintenance, repair work and small mechanical assemblies. Each ring shares the same compact diameter and circular form, making the set useful wherever a matching seal or replacement ring is needed to restore fit between moving or joined parts. The pack contains 10 identical rubber O-rings, which helps keep replacements consistent across repeated service jobs instead of mixing unmatched sizes. Their black finish makes them easy to distinguish from other small workshop parts during sorting and storage. In model building and accessory upkeep, small sealing components often matter as much as larger visible parts, especially when a worn ring needs a direct like-for-like swap rather than an improvised substitute. Kept in a parts drawer, tool case or bench organiser, these O-rings are ready for routine maintenance sessions and quick repairs. The uniform 3 mm format also suits builders who prefer to keep duplicate consumable parts available before starting detailed assembly or servicing work. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
3mm Shim-Set, RC spacer set, 0.1/0.2/0.3mm
300053585€11.29
The 3mm Shim-Set brings precise spacing control to RC car maintenance with 30 thin washers sized for 3 mm shafts. Each shim has a 3 mm inner diameter and a 5 mm outer diameter, making the set a practical choice for fine adjustment at suspension and other attachment points where excess movement can affect fit. Inside the set are 10 shims each in 0.1 mm, 0.2 mm and 0.3 mm thicknesses. That spread allows small, deliberate changes instead of forcing a single spacing value onto every location. On 3 mm suspension shafts, the shims can be placed to take up unwanted slack and refine how connected parts sit against one another. The ring format keeps the adjustment focused on the shaft position itself, which is useful when tuning linkage or suspension areas that react to very small dimensional changes. For workshop use, the set suits routine maintenance, chassis rebuilding and targeted setup corrections on many Tamiya RC cars. A builder can test one thickness, stack combinations where needed, and match the spacing to the exact attachment point rather than replacing larger components. The scope of delivery contains 1 spacer set with 30 pieces. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
3x0.7mm Aluminum Spacer Set, model accessory
309805645€6.29
These aluminum spacers in 3x0.7 mm format support accurate spacing in detailed model assembly, where a defined gap can influence fit, alignment and component position. The 10-piece pack gives a ready supply for workshop drawers, replacement needs or builds that use several matching spacers in one setup. The 3 mm size and 0.7 mm thickness make this set suited to fine adjustment work rather than broad structural filling. In model construction, spacers like these sit between mounted parts to create consistent separation and help maintain the intended position of screws, brackets or other fitted elements. Aluminum brings a clean, technical finish to this small but useful hardware format and fits naturally into precision-focused hobby work. Whether used during a fresh build, a repair or a measured setup change, the defined dimensions make selection straightforward when a specific spacing value is needed. Kept in a parts box or bench organizer, the set adds a practical option for builders who work through detailed fitting tasks one measured step at a time. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
3x10mm Alum. Turnbuckle Shaft, chassis accessory
300053892€11.99
These 3 x 10 mm aluminium turnbuckle shafts bring precise anti-roll bar adjustment to compatible chassis setups while adding a clear blue finish to the hardware. The set contains 4 shafts and is intended as a chassis accessory for fine tuning left and right anti-roll bar settings without removing the adjuster. The compact 3 x 10 mm dimensions suit dedicated on-road racing platforms where small setup changes matter. As a replacement for 9804250, this set gives a direct route to refreshing existing hardware with the same stated function. Compatibility is listed for TRF415MSX, TRF415MS, TB Evo. IV MS and TB Evo. IV. TA05 fitment is also specified, with the condition that adjusters must be shortened. At the workbench, these shafts support quick setup changes between runs when anti-roll bar balance needs a finer response. In regular maintenance, the 4-piece pack also helps keep a matching set ready for rebuilds, repairs or chassis-specific spares within a race box. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
4mm Shim Set, RC accessory, 0.1/0.2/0.3 mm
300053586€11.29
This 4 mm shim set brings fine mechanical adjustment to RC maintenance and model workshop tasks where shaft spacing needs a precise correction. The pack contains 30 shims in total, divided into 10 pieces each at 0.1 mm, 0.2 mm and 0.3 mm, so clearance can be tuned in small measured steps instead of forcing a single thickness into every job. Each shim fits 4 mm shafts and is intended for situations where more clearance is required. The thin ring format slips onto the shaft to change spacing directly at the point of assembly, which helps when rotating parts need a more exact position. Combining different thicknesses from the set also allows intermediate spacing values, giving more control during drivetrain setup, axle work or other moving assemblies that rely on accurate alignment. On the bench, the 3 thickness options support methodical trial fitting during maintenance, rebuilds or parts replacement. The grouped sizes make it straightforward to compare spacing changes, correct excess play and refine the fit of compatible components without replacing the shaft itself.
Other spare parts & accessories
5mm Body O-Rings, model accessory, 10 pieces
300054384€3.09
These 5 mm body O-rings are small model accessory parts that make a visible difference at the body mounts. Fitted to body mount rods, they allow fine height adjustment of the bodyshell position, so the shell can sit with a more controlled fit on the chassis during setup. The set contains 10 O-rings for replacement stock or fresh installation on compatible body posts. Their role is not limited to spacing: each ring also provides a cushioning effect between the bodyshell and the mount point. On rougher driving surfaces, that added cushion helps reduce body chatter that can appear when the shell moves against the posts over bumps. This gives the shell mount a tidier, more settled feel while the model is running. In workshop use, the rings are easy to keep on hand for routine maintenance, rebuilds, or shell changes between different bodyshell setups. They suit drivers who fine-tune shell height on body mount rods and want spare mounting hardware ready for regular track or car park sessions. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
5mm Shim Set, RC accessory, 0.1 0.2 0.3mm
300053587€11.29
This 5 mm shim set brings precise spacing control to RC chassis work, with 3 thicknesses at 0.1 mm, 0.2 mm and 0.3 mm for fine mechanical adjustment. Used at 5 mm fitment points, the shims help take up excess movement where a cleaner, tighter setup is needed around suspension parts or wheel axles. The set includes 30 shims in total, arranged as 10 pieces of each thickness, which supports repeated setup changes without relying on a single size. Small spacing differences can change how parts sit against each other, and these thin rings make those corrections measurable rather than improvised. On a maintenance bench, they can be selected to match the amount of free play present at a given point. On a fresh build, they support more exact placement of moving parts before the chassis goes into use. The shim assortment suits both on-road and off-road Tamiya vehicles, so the same pack can serve different running platforms in one workshop. Whether the goal is tidying axle movement, refining suspension fit or keeping a race chassis more closely adjusted, the 5 mm format gives a compact tuning part that earns its place in a spares box.
Other spare parts & accessories
6 mm Shim Set, model accessory, 0.1 0.2 0.3 mm
300053726€16.29
This 6 mm shim set brings precise spacing control to model assemblies that need a cleaner fit on 6 mm shafts. With 3 thicknesses at 0.1 mm, 0.2 mm and 0.3 mm, the set supports small corrections where mechanical play affects alignment, rotation or part position. The set contains 30 pieces in total, arranged as 10 shims of each thickness. That spread makes it possible to compare different spacer combinations during a build or while servicing an existing model, instead of working around a single dimension. The thin shim format suits jobs where only a fraction of a millimetre is needed to correct end float or reduce unwanted movement between parts. Used singly or in combination, the spacers help adapt the fit to the exact requirement of the assembly point. On the bench, the set suits gearbox work, axle spacing and other 6 mm shaft applications where measured adjustment matters. As a compact workshop supply for model maintenance, repair or fresh assembly, it adds a practical range of fine spacer sizes that can be kept ready for repeated mechanical setup tasks. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
A-Parts Gearbox F/R 58370, RC spare parts
300004432€14.29
This A-Parts sprue is made for the 58370 and provides black injection-molded components for the gearbox F/R area of the DF-03. The unassembled runner groups housing halves, covers and structural sections in one set, giving repair work a direct route back to the intended drivetrain layout. The molded pieces show reinforced ribs, screw holes and cylindrical shaft or bearing mounts that matter when a transmission case needs its original geometry. A larger frame-like section with elongated slots adds another chassis-facing support element, while rounded shell parts serve as protective case sections around moving drivetrain parts. Because the components are supplied on the sprue, each shape stays clearly separated until preparation begins, which helps with part checking before installation. The glossy black finish matches the technical look of many RC chassis internals. This spare parts set suits maintenance benches, rebuild projects and targeted gearbox repairs where damaged housings, brackets or covers need replacement with matching forms. It also supports keeping a DF-03 running with dedicated structural parts on hand for future service work.
Other spare parts & accessories
Alligator Clip for P. Stand, model tool set
300074528€5.99
These alligator clips add a simple, controlled way to hold small model parts while cement or paint dries. The spring-loaded hinge and serrated jaws grip components firmly, so freshly finished pieces can stay separated from the work surface and remain easier to handle during careful bench work. Each pack contains 4 matching clips, which supports parallel work on several parts in the same session. The oval wire loop at the end of each clip provides a clear connection point for mounting on a compatible stand. The clips are intended for use with the Painting Stand, Work Stand and Bottled Paint Stand named in the product data, making them a practical addition for painting, gluing and drying steps where direct hand contact can disturb a finish. On a model bench, the clips can hold newly cemented sections while joints set, or keep painted components raised and separated between coats. Their compact metal form suits detail-focused tasks where small parts need a temporary grip point and a cleaner path through finishing work.
Other spare parts & accessories
Alum. Turnbuckle Wrench blue, model tool, 3.0 mm
300053602€14.99
The Alum. Turnbuckle Wrench blue is a dedicated model tool for fine setup work on vehicles with 3 mm adjustable tie rods or camber rods. Its 3.0 mm clamping axle format is made to engage the turnbuckle directly, so alignment changes can be made with a controlled hand movement at the workbench between runs or during a full chassis service. The blue aluminum handle combines low weight with a firm feel, and the ribbed cylindrical shape supports stable finger placement while small adjustments are made. A forked open-end tip slides around the rod section to apply leverage where a standard wrench would be too bulky. This focused shape suits RC maintenance jobs where steering links and camber rods sit close to surrounding parts. The scope of delivery contains 1 clamping axle wrench. On a tuning bench, in a pit box, or beside a partly stripped chassis, this tool supports repeatable suspension and steering setup work without taking extra space. It also works well as a dedicated addition to a model building tool roll where 3 mm linkage hardware is adjusted regularly. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Aluminum Reinforced Tape, model accessory, 50 mm
300053351€10.291 m = €5.15
This aluminum reinforced tape is made for model applications where high heat builds up close to the body shell. In gas operated vehicles, an exhaust pipe can run near the polycarbonate body, and the adhesive aluminum surface forms a heat resistant shield in that exposed area. The roll measures about 50 mm in width and 2 m in length, which gives flexible coverage for trimming sections to the required size. The reinforced construction suits placement along body areas that sit near hot exhaust routing, while the metallic surface is designed to handle heat exposure where direct proximity could otherwise mark or damage the polycarbonate. Scope of delivery: 1x aluminum tape reinforced. Used on RC vehicle body shells and similar model setups, the tape supports focused protection exactly where heat management matters most. It fits practical workshop tasks such as lining a body section near the pipe outlet, covering a local hot spot, or adding a barrier on an inner panel before the next run. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Aluminum Spacer Set 5.5/3mm, model accessory
300053539€14.69
This aluminum spacer set brings precise spacing control to model assemblies that use 3 mm screws. With a 3 mm inner diameter and 5.5 mm outer diameter, the rings sit neatly at screw-mounted connection points where height, clearance or part position needs fine adjustment. The blue and silver finish also makes the different pieces easy to sort on the workbench during setup changes. Inside the set are 6 spacer thicknesses: 0.5 mm, 1 mm, 1.5 mm, 2 mm, 2.5 mm and 3 mm, with 4 spacers supplied in each size. That spread supports small, measurable changes instead of broad jumps, which is useful when tuning the fit of linked parts or correcting alignment across paired mounting points. The reference application shown in the data places the spacers with suspension arm blocks and damper mounts, and the same dimensions also suit other assemblies built around 3 mm screw hardware. On a chassis build or maintenance session, the set supports repeatable adjustments when comparing one mounting position against another. Matching quantities across all 6 sizes help keep left and right sides consistent while leaving room to test different stack heights in mechanical layouts that need exact spacing.
Other spare parts & accessories
Antenna for 56019, model accessory, 175 mm
305365011€4.49
This antenna for 56019 is a dedicated model accessory with a stated length of 175 mm, intended for use where the matching reference calls for this exact part. The slim rod format gives the model a clean, defined finishing detail while keeping the replacement focused on the named application rather than a generic spare. The part is supplied as 1 piece and is described simply as an antenna for 56019, which keeps selection clear when a specific replacement is needed. The visible form shows a long metal rod with shaped ends, including a hooked bend at one end and a coiled section at the other, indicating a functional mounting or connection point within the matching model setup. That concrete shape matters when replacing a missing or bent antenna, because the end form can be just as important as the overall length. Used on the correct model, this 175 mm antenna suits repair work, parts replacement, or the completion of an existing build that needs the specified external component. It fits naturally into workshop tasks such as restoring a stored model, replacing a worn original, or finishing a project with the named 56019 reference in mind. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Antenna Pipe 300mm, model accessory, black
306095010€0.79
This black antenna pipe adds a neat, functional finishing detail to compatible RC model setups. With a length of 300 mm or 30 cm, the tube gives the antenna a defined route and helps maintain a clean layout above the body where a loose wire would look untidy. The straight tube form makes it useful as a replacement part in routine maintenance, after repairs, or when refreshing an older build with worn running hardware. Its single-purpose design keeps the fit straightforward: the pipe sits in the model's antenna mount and supports the aerial in an upright position. The black finish keeps the look understated, which suits a wide range of body colours and chassis layouts without drawing attention away from the model itself. In workshop use, a spare antenna pipe is a practical part to keep alongside other RC maintenance essentials, especially for builds that still use a visible aerial tube. It also suits restorations where small external details help return a model to a complete, ready-to-run appearance. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Antenna Pipe 380mm, model accessory, clear
306095001€0.89
This clear antenna pipe is a straightforward model accessory for RC setups that use an external aerial guide. With a length of 380 mm, it provides a long tube that can be fitted and trimmed to match the required antenna height on the model, keeping the wire routed in a visible, upright position above the bodyshell. The transparent finish leaves paintwork, markings and body lines unobstructed, which helps preserve the look of the completed model while still making the antenna route easy to follow during fitting. Supplied as 1 piece, it works well as a direct replacement for a damaged tube or as a spare kept on hand for workshop use. The simple tube format also makes it useful across routine maintenance tasks where a clean, correctly sized aerial guide is needed. On the bench, the 380 mm length gives enough material for model-specific adjustment before final installation. During transport, storage and running sessions, the fitted tube helps keep the antenna wire guided consistently instead of leaving it loose around the shell area. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Anti-Wear Grease 3g, model lubricant tube
300053439€12.991 kg = €4,330.00
Anti-Wear Grease in a 3 g tube supports smooth maintenance work on model drivetrains by combining high viscosity with precise placement. On differential gears, shafts and drive axles, the grease adheres well to rotating parts, so lubrication stays where the mechanism needs it during repeated movement. The formulation is described for model vehicles and is supplied in a compact tube with a fine, narrow nozzle for controlled dosing on small contact points. That narrow outlet helps place a small amount directly onto gear teeth, axle sections or shaft ends instead of coating surrounding areas. The grease is temperature stable and retains its viscosity over a wide temperature range, which helps keep application characteristics consistent as moving parts warm up in use. The supplied quantity is 3 g, making it suited to targeted servicing rather than bulk workshop filling. In regular upkeep, the tube fits neatly into a field box or bench drawer and is ready for quick drivetrain attention between runs. It suits focused lubrication tasks on compact assemblies where accurate placement matters, especially around differentials and other enclosed rotating components. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Axle Spring (2), spare part for model chassis
309808008€2.99
This set of 2 axle springs is a dedicated spare part for 58347 and is shaped for mechanical return action at the axle assembly. Each spring is formed from silver-coloured metal wire and uses a tightly wound coil with one short straight leg, one longer angled arm and a small loop at the end, making the part easy to identify during maintenance. The geometry shown in the part itself matters: the coiled section stores torsion, while the two arms transfer that force back into the moving mechanism. That makes these springs suitable for restoring rotational resistance, return tension or repositioning in the intended axle location on a compatible model. Supplied as a matching pair, the set supports like-for-like replacement where both sides of an assembly use the same spring form. For workshop use, the clear standalone shape helps with part checking before fitting and with replacing worn, bent or missing hardware in an existing chassis setup. As a model spare part rather than a general hardware spring, it is best used where the 58347 fitment and the pictured form match the original assembly requirement. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
B-Parts Gearbox Super Clod Buster spare parts
300005294€19.49
B-Parts Gearbox Super Clod Buster 58321 is a replacement sprue for model maintenance and repair, bringing key transmission-area components together in one clearly structured set. The black injection-moulded frame presents the parts in their original grouped layout, which helps with visual checking before each piece is removed and installed. The sprue shows 2 large matching housing halves, a rounded cover plate, 2 circular discs with evenly spaced holes, a larger curved cover piece, and several smaller link arms and connectors. One housing half features an integrated cylindrical section, indicating a dedicated enclosure area within the gearbox assembly. The opposite half carries reinforcing ribs and multiple screw points, giving the rebuilt section the same shaped mounting structure as the original part set. Small moulded part numbers are also visible on the frame, which supports part recognition during a careful rebuild. This spare-parts set suits workshop use when a Super Clod Buster gearbox section needs replacement after wear, damage or a detailed restoration. It also helps keep a rebuild consistent by supplying matching moulded pieces from the same B-Parts group rather than mixing unrelated components.
Other spare parts & accessories
Ball Differential Grease 10g, RC lubricant
300053042€11.39
Ball Differential Grease 10g is a dedicated lubricant for ball type differential gearing in RC model vehicles, supplied in a compact tube with an applicator nozzle for controlled placement on small drivetrain parts. The 10 g fill gives a practical amount for routine servicing, whether the differential is being refreshed during a rebuild or maintained between running sessions. The grease is specified for differential use rather than general-purpose lubrication, which keeps the copy focused on the part it is made for. The supplied tube format helps direct the grease into tight mechanical areas where ball differential components need careful coverage. Compatibility notes in the data reference a wide range of chassis families when used with the stated related parts, including XV-01, XV-01T, XV-01 PRO, M-07 CONCEPT, M-08 CONCEPT, TA06, TA06 PRO, TA06 MS, TT-02, TT-02D, TT-01 TYPE-E, TT-01D TYPE-E, TT-02RR, TT-02FT, TT-02B, MF-01X, M-05, M-05 PRO, M-05 ver.II PRO, M-06, M-06 PRO, DT-02, DT-03 and DT-03T. On the bench, the narrow nozzle supports precise application during drivetrain maintenance, helping keep grease where the ball differential needs it instead of spreading it across surrounding parts. In workshop use, the small tube stores easily with other RC service supplies and is ready when a ball diff setup is due for fresh lubricant. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Basic File Set Smooth Dbl. Cut(3), hobby file set
300074104€8.29
The Basic File Set Smooth Dbl. Cut(3) brings 3 distinct file shapes into one compact bench set for shaping, smoothing and refining small model parts. Flat, round and semi-circular profiles make it easier to match the filing surface to the contour being worked, whether the task is cleaning an edge, opening a curve or evening out a narrow recess. Each file is 140 mm long, with a 2.5 mm handle diameter that suits close hand control on detailed work. The double-cut surface uses 38 cuts per cm, giving the files a fine, even bite that supports a smooth finish rather than heavy stock removal. This makes the set especially suited to surface preparation on plastic scale models, while still handling Mini 4WD parts and selected metal areas where careful finishing matters. At the workbench, the different profiles help move from straight runs to rounded sections without switching to oversized tools. Black rubber grips keep the hold consistent during short filing passes, and the included vinyl case stores the 3 files together between build sessions and transport.
Other spare parts & accessories
BB-01 Main Chassis, RC spare part for BBX
319335893€21.29
The BB-01 Main Chassis is the core frame section for BBX 58719 and provides the shaped base around which the vehicle layout is built. Its black molded form combines an elongated tub design with a large central compartment, creating dedicated space for the main internal installation while keeping the underside profile structured by integrated ribbing. Across the frame, molded screw posts and cylindrical mounting areas define where matching assemblies attach, while rectangular side slots add further connection points along the chassis walls. The one-piece construction keeps the geometry consistent across the length of the frame, which matters when replacing a worn or damaged base on an existing BB-01 build. The underside view shows a symmetrical layout with reinforcement lines running through the tub, giving this spare part the form needed to carry the rest of the chassis hardware in its intended position. This replacement part suits repair work, rebuilds and parts-based restoration of a BBX 58719 using the BB-01 platform. It fits naturally into workshop sessions focused on bringing an RC vehicle back into running condition or preparing a fresh chassis foundation for the next stage of assembly.
Other spare parts & accessories
Body Mount Extension Set 5.5 mm, RC car accessory
300054604€7.99
The Body Mount Extension Set 5.5 mm adds a precise height correction to RC car body posts when a different bodyshell calls for more clearance. Each extension piece is designed to work with 5.5 mm to 6 mm diameter body mounts, and the included snap pins lock the selected position through the adjustment holes for a firm mechanical hold. Inside the set are 4 body mount extensions, plus 4 snap pins in 6 mm and 7 mm sizes. The parts are intended for touring car chassis and M-Chassis cars, where body posts may already have been cut down for another shell. Instead of replacing the full mount, this set extends the existing post by 5.5 mm and keeps the mounting point usable for another body setup. The fitting method shown in the leaflet uses the extension on the chassis-side body mount and secures it with a snap pin through the cross hole. This accessory suits workshop adjustments, shell swaps and rebuilds where body height needs a small, exact correction rather than a full change of mounts. It is compatible with TT-01, TT-02, TA05, TA06, TB-03, TB-04, XV-01, FF-03, M-05 and M-06 chassis body mounts, making it a practical addition for keeping several RC car bodyshells in rotation.
Other spare parts & accessories
Body Mount Plate BH 7/8, model accessory set
319808269€11.49
The Body Mount Plate BH 7/8 is a model accessory set for the 58441 and 58452 references named in the data. With 2 mounting plates included, it supplies the specific hardware needed for work on the body mount area, whether the goal is replacing an existing part or completing a matching assembly step on the intended build. Each plate is shown as a formed metal component with a rectangular profile, rounded corners, 2 screw holes and a shaped center section. Those details matter during installation, because the hole positions and stamped form help the plate sit in the intended location and connect with the surrounding structure as designed. The BH 7/8 designation keeps the part identification aligned with the named application, which is useful when sorting spares for maintenance or rebuild work. The compact hardware format also makes this set a focused choice when only the mounting section needs attention rather than a wider parts replacement. On a workshop table, the 2 plates can be set alongside the target chassis parts and matched directly to the specified 58441 or 58452 build. For routine upkeep, rebuilds or parts sorting, this set keeps the replacement task centered on the exact mounting hardware named in the data. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Body Mount Set, RC spare parts for DT-03 chassis
300050855€9.99
This E-parts body mount set is made for selected RC chassis and supplies the core parts needed when body fixing points need replacement. It fits DT-03, DT-03T, G6-01, G6-01TR, TL-01, FF-02 and WR-02 applications named in the data, combining molded mounts with matching hardware for a direct service task at the shell mounting area. The black components are shaped for chassis attachment and body support, while the included mounting material covers the fastening work tied to this set. Multiple hole positions on the molded parts allow the mounting point to be set according to the chassis layout and shell position, which matters when replacing worn posts or correcting body fit after use. As E-parts, these components suit maintenance benches, rebuilds and parts boxes where chassis-specific replacements need to stay close at hand. The set works well during routine RC upkeep, after a cracked mount, or when a stored chassis is being returned to running condition with the correct fixing parts. In workshop use, the combination of mounts and screws keeps the repair centered on one compatible set instead of mixing unmatched hardware from different spares. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
CC-01 D-Parts, body mount spare part
309005741€7.99
CC-01 D-Parts is a body mount spare part set for model maintenance on the 58324 reference. The set provides 2+2 replacement parts, making it useful when original mounting points are worn, missing or damaged and the shell needs the correct support points back in place. The designation D Parts identifies this set within the CC-01 parts structure, which helps when matching replacements to an existing build or planning a repair. As a model supply rather than a general-purpose accessory, it is intended for a specific application instead of broad compatibility across unrelated chassis types. The body mount function matters at the point where the shell is positioned and secured, so using the named replacement set helps keep that connection in line with the original layout. Batteries are not included. This spare part set fits naturally into workshop tasks such as replacing lost components during a rebuild, refreshing a used chassis, or keeping matching parts on hand for future maintenance. It also works as a practical stock addition alongside other service parts for the same CC-01 reference, especially when a repair calls for the exact D Parts designation rather than a substitute. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
CC-01 M-Parts Toyota, model spare parts, 2 pcs
309115264€26.49
CC-01 M-Parts Toyota is a spare parts set for model work on kit 58445 and provides 2 replacement parts for the matching build. The black injection-molded frame groups the components on a single sprue, so the original shapes, attachment points and part orientation stay easy to reference during repair or rebuild tasks. The molded layout shows several distinct forms, including long curved sections, mirrored arm-shaped pieces, smaller mounting blocks and round connection elements. These details matter when a damaged section needs to be replaced with a part that matches the intended geometry of the original assembly. Because the pieces remain attached to the runner before removal, each section can be identified against the build step before cutting it free. The preformed holes and connection points support clean integration with the corresponding assembly positions in the specified model. This set fits situations such as replacing lost parts during a paused build, refreshing worn sections on an existing chassis, or keeping a stored model ready for future maintenance. In a workshop drawer or alongside a current project, the sprue serves as a direct source for matching CC-01 M-Parts Toyota components tied to kit 58445. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
CC-02 LF 6mm Ball Collar (18), chassis parts
300054945€21.19
The CC-02 LF 6mm Ball Collar set adds a focused drivetrain and suspension upgrade to CC-02 chassis cars by replacing kit-standard C9 parts with low-friction steel components. Each collar uses a plated surface to minimise resistance where moving parts pivot and slide, so link-arm action feels cleaner and more direct when the chassis works over uneven terrain. The pack includes 18 collars in total. Of these, 16 are assigned to the link arms, while 1 fits the steering linkage and 1 fits the battery plate, giving the set a chassis-specific layout rather than a generic hardware mix. The 6 mm size matches the stated fitment, and the steel construction brings a precise contact surface to the suspension hardware. In rigid suspension setups, that lower resistance helps the links move with less drag through their travel, which supports more consistent articulation across rough sections. Installed on a CC-02 build, the collars suit tuning sessions that focus on suspension response and chassis control rather than cosmetic changes. They also fit maintenance work where worn standard parts are being swapped for smoother-running hardware in the steering and link assemblies.
Other spare parts & accessories
Chassis Protective Sticker, RC accessory, 0.3 mm
300054499€15.79
This hard protective film is made for the underside of an R/C vehicle chassis, where repeated contact with the track surface can leave marks during regular running. At 0.3 mm thick, it adds a thin sacrificial layer that takes the abrasion while leaving the chassis itself covered. The transparent finish keeps the visual character of the model unchanged. The sheets measure 180 x 330 mm and come in a pack of 2, providing material that can be cut to suit different chassis shapes and lengths. The highly adhesive surface is intended to bond securely under the main chassis, where constant rubbing and sliding place the greatest demand on protection. Because the film is supplied as full sheets rather than pre-cut sections, it can be adapted to a wide range of R/C vehicle layouts. This makes it useful both for a fresh application and for replacing worn film after repeated use. In workshop preparation, the film can be trimmed before a run and applied to the areas most exposed to scraping. After track sessions on abrasive surfaces, the protective layer helps keep the underside cleaner in appearance and reduces direct wear on the chassis base.
Other spare parts & accessories
Craft Tweezers, papercraft tool, 140 mm
300074080€22.49
These craft tweezers are designed for papercraft work, where small tabs, narrow folds and glued sections need controlled handling. At 140 mm in length, they offer a compact format that sits easily in the hand while keeping the tip visible during close, detailed tasks. The foremost part uses an original TAMIYA design created to improve effectiveness in gluing, paper bending and the drying process. That shape helps hold and guide thin paper parts with more control than fingertips alone, especially when working along edges, corners and tight contact points. The tweezers are made from SUS410 stainless steel and finished with a hairline surface, giving the tool a precise, clean look suited to bench work and hobby tables. The pointed, angled form also helps reach into small spaces between folded sections without covering the working area. Sticker and decal application is another practical use, particularly when small markings need careful placement before final pressure is applied. On a papercraft build, during detail finishing, or while handling delicate printed parts, these tweezers support steady, accurate movements across each step of the work. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
DF-03 Chassis, RC spare chassis frame
309335449€13.99
The DF-03 Chassis serves as the structural core for a compatible RC vehicle build, forming the main lower frame that carries the mechanical layout. Its black molded construction combines an elongated central body with raised side sections, giving the assembly a defined platform for attaching major modules while keeping the underside compact and purposeful. Across the frame, multiple drilled and countersunk mounting holes create fixed attachment points for screws and hardware. A large oval opening in the center is joined by shaped slots and recessed areas, which help organise the placement of installed parts and leave room for routed connections within the chassis layout. One end uses a rectangular mounting section with 4 visible countersunk holes, while the opposite end extends into a flat plate with additional drilled points for further fitment. These details make the frame more than a simple base plate: it establishes the geometry that the rest of the DF-03 build follows. Used as the lower platform in a rebuild, repair or replacement project, this chassis frame supports a clean restart when an existing vehicle needs a fresh foundation. It also suits workshop stock for keeping a compatible DF-03 machine in running condition after wear or damage to the original frame. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
DN-01 Inner Sponge Front Kit, foam insert set
300051448€6.69
DN-01 Inner Sponge Front Kit is a front foam insert set for selected buggy chassis, built to sit inside the front tyres and support their shape while the model is running. The set contains 2 grey open-cell foam rings and is specified for DT-03, DT-03T and DT-02 chassis applications. Inside the tyre, each insert fills the cavity between tyre and wheel so the front end keeps a more defined profile as loads shift through steering inputs and uneven ground. The donut-shaped foam form shown in the set is intended for front use, which matters when tuning the balance of a buggy around turn-in and directional control. Compatibility is stated with tyre references 51207 and 54284, giving a clear match point when replacing worn inserts or building a fresh wheel and tyre setup. The foam material also keeps the setup light compared with heavier internal fillers. This 2-piece set suits routine maintenance, a chassis refresh or a second wheel set prepared for another surface. On a running DT-03, DT-03T or DT-02 build, fresh front inserts can help restore a more even tyre profile after repeated use and compression. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Double-Sided Tape 20mm x 2m, black tape roll
300054693€14.79
This black double-sided tape gives R/C model work a clean, practical way to mount and protect equipment in one step. The 20 mm x 2 m format provides a continuous roll that can be trimmed to the exact length needed, whether the task calls for a short fixing point or a longer contact strip across a wider surface. Its heat-resistant construction suits model layouts where mounted components sit close to running electronics and need a dependable adhesive layer between parts and the chassis or mounting surface. The foam-style tape profile also helps create a slight buffer where equipment needs both attachment and a degree of separation from the surface below. Compared with pre-cut strips, the roll format keeps sizing flexible during bench work and repeated maintenance. It can be cut for receiver boxes, electronic modules or other onboard components where tidy placement matters. One roll is included.
Other spare parts & accessories
DT-04 Chassis blk, RC chassis part, black tub
319335912€12.79
DT-04 Chassis blk provides the core lower frame for an RC model build, with a black molded tub shape that brings the main structure together in one substantial component. Raised sidewalls, integrated screw posts and a ribbed interior create a clear base for positioning major assemblies while keeping the layout defined on the bench. The molded underside geometry shows how this chassis part is designed to carry more than a flat floor alone. Reinforcing ribs run through the interior to stiffen the form, while circular holes and mounting points are placed directly into the tub for mechanical fastening. The extended end plate section adds another structured area with several fixing holes and ribbed supports, giving the build extra attachment space where connected assemblies need a stable anchor. As a replacement or project part, this chassis tub restores the original lower structure without changing the designated DT-04 layout. On a rebuild, repair or fresh parts-based assembly, this component sets the position for the rest of the chassis around a single molded base. The black finish matches the functional look of an RC underframe, and the one-piece construction keeps the mounting geometry together in the form intended for the DT-04 platform. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
DT-04 Full Ball Bearing Set, chassis accessory
300022092€24.29
The DT-04 Full Ball Bearing Set adds a precise drivetrain and steering upgrade to the DT-04 chassis with 18 metal bearings in 3 sizes. Installed in rotating points across the chassis, the bearings replace plain support parts with rolling contact, which helps moving assemblies turn with less drag and a smoother mechanical feel. The set includes 4x 850, 4x 1050 and 10x 1150 bearings, matching the different mounting points used in the DT-04 layout. That size spread makes the set suitable for a complete bearing conversion rather than a partial refresh of only one section. In the drivetrain, freer rotation supports more efficient transfer of motor output through the transmission. In the steering system, the same bearing construction helps linked parts move with a more direct action at the front end. This chassis accessory suits a new DT-04 build as well as later workshop maintenance when worn parts are being replaced. The small, shielded metal bearings are arranged as a dedicated fitment set for the platform, making them a practical choice when the goal is a cleaner-running buggy with reduced mechanical resistance in its key moving assemblies. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
DT-04 M Parts, chassis mount spare parts
319115594€11.49
The DT-04 M Parts gearbox and chassis mount set provides replacement components for RC model maintenance where structural sections need to be renewed. Supplied as black injection-moulded parts on sprues, the set is arranged for clear identification before trimming, sorting and installation. The visible parts tree contains multiple connected components shaped for functional mounting and support roles, including chassis-related sections, bracket forms and frame elements. This format helps keep small pieces together until they are needed at the bench and allows each part to be checked against the original assembly before removal from the runner. The moulded layout is suited to repair work after wear or damage, and it also supports planned rebuilds where a fresh gearbox or chassis mounting section is required. The technical presentation keeps the focus on fit, structure and correct part selection. On a workbench, the sprue format makes it easier to compare each section with the existing RC vehicle before cutting and fitting. During servicing, the set can be used to replace damaged mounting areas, refresh key structural points or prepare a stored chassis for reassembly with the correct DT-04 M components. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
E-Ring Set, model accessory, 17 pcs 2mm 3mm 4mm
300050380€2.99
This E-Ring Set brings small but essential fastening hardware into model assembly with 17 dark metal retaining clips in 3 sizes: 2 mm, 3 mm and 4 mm. Each E-ring is shaped to snap onto a matching groove on a shaft, axle, rod or pin, where it holds a mounted part in position while keeping the fixing compact and mechanical. The size spread makes the set useful across different fixing points instead of limiting the bench to a single diameter. In practical use, an E-ring is pressed onto the grooved end of a metal part so the open side clips over the shaft and the ring seats into place. That mechanism suits wheel mounts, axle retainers and other small moving assemblies where a screw or nut would take more space. The dark metal finish matches the function-focused character of workshop spares and replacement hardware. Kept in a parts box, drawer insert or service tray, the set supports routine maintenance as well as the recovery of lost clips during rebuilds. The stated scope of delivery is 1 set with 17 E-rings, giving a ready stock of common small retainers for model work that depends on secure, correctly sized mechanical fastening. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
F104 Disc Ball Set, chassis spare part, 3 mm
300051347€5.69
The F104 Disc Ball Set is a dedicated spare part for ball differential maintenance on compatible F104 series chassis. With 8 steel balls and matching pressure plates in a 3 mm format, it supplies the key contact parts used in the differential assembly and keeps replacement focused on the stated drivetrain area. Compatibility is specified for F104PRO II chassis, F104W chassis, F104 chassis and F103GT chassis. The steel construction suits the repeated contact points inside a ball differential, where smooth, consistent interaction between the balls and plates is central to the mechanism. Instead of a broad assortment of unrelated workshop parts, this set stays specific to one service task and one family of chassis. The scope of delivery contains 1 balls and pressure plate set. On the workbench, that clear compatibility helps when preparing a planned refresh of an existing F104 drivetrain or keeping matching spare parts ready between running sessions. In a parts box for formula chassis maintenance, the 3 mm specification gives a direct reference for selecting the correct replacement set for the listed platforms. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Flanged Tube, model accessory, 4.5 x 3.5 mm
309804382€4.49
This flanged tube is a small model accessory specified at 4.5 x 3.5 mm and listed with detailed dimensions of 3.1 x 4.5 x 4.0 mm. The flanged form helps distinguish the part from a plain tube when a build or repair calls for a defined edge and a precise seated position within an assembly. The pack contains 2 matching pieces, which suits jobs that need a pair of identical fittings rather than mixed hardware. In model maintenance, exact measurements matter, and the stated 3.1 mm, 4.5 mm and 4.0 mm figures give a clear reference when checking parts against an existing setup. The compact format makes this accessory relevant for detailed replacement work, careful restoration, or keeping spare hardware ready for future servicing. On the workbench, a correctly sized flanged tube can save time during part selection because the specification is already narrowed to a defined format. For ongoing model upkeep, 2 identical tubes also make it easier to complete symmetrical mounting points or store a matched spare set alongside other small workshop parts. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Flanged Tube, model accessory, 4.5 x 3.5 mm
309808021€3.09
This flanged tube set is a small but specific model accessory for repair, maintenance and parts matching. The pack contains 2 pieces, and the stated 4.5 x 3.5 mm format gives a clear reference point when an existing assembly calls for the same size and flanged construction. The source data also lists the dimensional specification as 3.1(4.5) x 3.5(4.0) mm, which adds another concrete identifier for checking fit against a current build or replacement need. A flanged tube is typically chosen for its defined shoulder and seating position within a mechanism, so the named form matters as much as the measurement when selecting the correct hardware. In a workshop drawer, this kind of small component helps keep repair jobs moving without substituting an unmatched part. Used during model upkeep, rebuilds or careful parts sorting, the 2-piece set supports direct replacement where the same tube is needed again. It also works as a practical stock addition for builders who keep commonly used hardware sizes on hand for future service tasks. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Gear Differential Putty, tuning accessory, 25 g
300042247€8.29
Gear Differential Putty is a tuning accessory for transmission differentials in model vehicles, supplied as 25 g in a plastic case. By controlling the differential action, it creates an effect close to direct coupling, changing how the drivetrain responds when load builds through the driven wheels. The putty is applied as a physical insert rather than a mechanical replacement part. The rolled material is cut with scissors, formed to about 3 mm in diameter, and then packed into the transmission differential. This gives a clear, hands-on way to adjust internal resistance with small portions instead of replacing the whole differential assembly. The method suits fine setup changes, because the amount and shape of the putty can be prepared before installation. The supplied case keeps the material contained between workshop sessions. Under heavy load from the road surface, the transmission moves to help avoid damage to the drive system, so the tuning effect is paired with protective drivetrain behavior. This makes the putty useful for setup work on model vehicles where differential response has a direct influence on handling and power delivery during running sessions. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Heat Resistant Doublesided Tape, model accessory
300050171€6.791 m = €11.32
Heat Resistant Doublesided Tape (5) is a model accessory for mounting, repair and ongoing workshop use where an adhesive layer needs to stay in place during detailed build steps. The set contains 1 adhesive tape pack with 5 pieces, giving a clear supply for replacement or fresh application on compatible model tasks. This version is identified as a replacement for 500908078, which helps match it to an existing parts requirement without guesswork. The heat resistant specification makes it suitable for applications where standard adhesive material may not be the intended choice. As a model supply rather than a finished vehicle or kit, the focus stays on a practical consumable that supports fitting, securing and maintenance work across build benches and repair sessions. On an active project, the 5-piece format allows one strip to be used where needed while the remaining pieces stay ready for later adjustments, part changes or follow-up repairs. It fits naturally into model assembly, restoration and parts replacement work where accurate, purpose-made supplies keep the process moving. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Hi-Torque Servo Saver Black, RC spare part
300051000€17.99
Hi-Torque Servo Saver Black brings a focused steering upgrade or replacement part to RC chassis work, with a 26-piece set that combines black molded components and metal hardware in one servo saver assembly. Built for the MF-01X chassis, it gives the steering system the dedicated parts needed where controlled force transfer and linkage connection matter during running and maintenance. The set contains the servo saver itself together with screws, nuts, washers, retaining rings and threaded ball studs. Those ball studs create the mounting points for linked steering rods, while the retaining rings secure the relevant rotating or stacked parts within the assembly. Combined use with 54120 is specified in the data, which matters when matching the setup to the intended chassis configuration. The black finish keeps the installed assembly visually consistent with surrounding chassis parts, and the grouped hardware avoids piecing together separate fasteners for this specific mechanism. On the bench, this spare part suits routine servicing, parts replacement or a fresh chassis build centered on the MF-01X platform. It fits naturally into steering work where worn saver parts, missing hardware or a chassis-specific installation calls for the correct component set rather than a generic substitute. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Hi-Torque Servo Saver, 1:10 accessory, white
300050473€17.29
The Hi-Torque Servo Saver in white is a steering accessory for RC model setups that need a precise, compatible linkage part. Designed for all Tamiya chassis and many 1:10 models, it supports cleaner steering response while improving return after direction changes, making it useful for fresh builds, maintenance work and replacement installs. The set combines white molded components with the small hardware needed to mount and connect the assembly, including screws, nuts, washers, retaining rings and ball-ended linkage parts. Those ball-joint style connectors support the steering linkage where controlled movement and secure attachment matter, while the retaining rings and fasteners complete the mechanical fit. For MF-01X chassis, combined use with 54120 is specified, which helps align the part choice with that chassis configuration. On a workshop bench, this servo saver suits routine servicing as well as targeted steering updates on compatible 1:10 RC cars. It also works as a useful spare for keeping an existing chassis ready when worn steering parts need to be replaced with matching hardware and mounting pieces. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
J-Parts for Subaru Impreza WRC'08, model parts
309115244€14.19
This J-Parts set is made for the Subaru Impreza WRC'08 from kit 58426 and serves as a dedicated replacement parts option for that exact model. The defined J-Parts designation helps identify the correct section within the original build, which is useful when an existing model needs a missing or worn component replaced rather than improvised with a non-matching part. Because the data names this set specifically for 58426, the fit reference is tied to that kit and to the Subaru Impreza WRC'08 body version listed here. That makes the set relevant for repair work, restoration of an older build, or keeping a previously assembled model in running or display condition with the intended parts group. As model supplies, these parts are aimed at maintaining an existing build rather than changing it into a different version. On the workbench, a dedicated replacement set like this can save time when sorting spares for a rebuild or when completing a model that is missing one defined parts section. It also gives collectors and builders a clear way to keep kit 58426 aligned with its original specification over repeated maintenance cycles. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Joint Boot BB21, spare part for Mt.Beetle
316255002€4.39
Joint Boot BB21 is a model spare part specified for the Tamiya 58618 Mt.Beetle. The long black component has a bellows-style form with several ribbed sections and thicker collar points, a shape used where a fitted cover needs to move with the linked assembly while keeping the area around the joint enclosed. The moulded one-piece construction gives the part a clean technical profile for maintenance, replacement or a faithful rebuild of the original model layout. Its accordion-like sections indicate controlled flexibility, allowing compression and extension as the connected mechanism moves. The stepped ends and central collars provide defined seating points that match the intended mounting position rather than acting as a generic sleeve. That makes BB21 useful when an existing boot is worn, split or missing and the assembly needs the correct designated part again. In workshop use, this spare part fits naturally into repair sessions focused on keeping a Mt.Beetle complete and mechanically tidy. It also suits stock-box planning for regular running models, where model-specific service parts help keep maintenance work straightforward and consistent with the original specification. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
LED Stopper, model accessory, 2 pcs.
309005859€5.99
This LED Stopper set is a focused model accessory for detailed assembly work, supplied as 2 sprues with multiple molded stopper pieces ready to be removed and fitted as needed. The compact format keeps matching parts together on the runner, which helps maintain order while preparing small components at the bench. Each sprue is injection molded in ABS and marked with part identifiers, giving the set a clear technical character that suits precise hobby tasks. The forked stopper shapes shown on the runners support controlled placement in builds that call for small retaining parts. Because the pieces stay attached until needed, sorting and handling remain straightforward during preparation. The uniform molded layout also helps when checking parts before cutting them free. On the workbench, this set fits naturally into careful model sessions where small components and clean organization matter. It suits builders who want a dedicated supply of matching stopper pieces on hand for compatible projects and detail-focused assembly steps. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
LW X-Joint for W Cardan, model spare part
300042319€5.69
The LW X-Joint for W Cardan is a dedicated spare part set for compatible model driveline assemblies. With 4 replacement pieces in the pack, it supports routine maintenance where worn joint parts can affect the movement of a W Cardan setup during running sessions. Used in the correct compatible assembly, each X-joint serves as a small but important connection point within the driveline. Replacing these parts can help restore the intended fit and motion of the mechanism without changing the overall layout of the model. The set is suited to workshop stock, scheduled service work, or repair after wear on an existing compatible setup. Its focused format keeps the purchase tied to one concrete task: renewing the X-joint section of a W Cardan assembly with matching spare parts. On the bench, the 4-piece pack is practical for keeping replacement parts ready before a maintenance session starts. It also suits hobby storage where frequently used driveline spares are kept together for compatible model repairs and ongoing upkeep. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
M-05 Ver.II A Parts, chassis spare parts set
300054605€18.79
The M-05 Ver.II A Parts chassis set is a focused upgrade and replacement option for the M-05 platform, bringing Ver.II chassis geometry to existing builds while also restoring worn sections on the M-05 Ver.II PRO. Black molded chassis components form the core of the set, with the layout shaped around updated battery and servo fitment options. Within the chassis, parts A8 and A9 allow installation of square-shaped battery packs in place of earlier chassis pieces, and the instruction data notes that the battery pack is secured with glass tape. A redesigned A3 section opens space for a low-profile servo during assembly, while standard-size servo installation uses part A7 with 3 x 18 mm tapping screws. The motor position shifts 3 mm closer to the center, changing the weight distribution within the chassis. The set is also compatible with Item 54606 one-piece lower suspension arms, which allows rebound stroke adjustment when that arm set is used. Some bodies may require trimming where they interfere with the chassis. This chassis parts set suits maintenance, repair and specification updates on compatible M-05 variants. It fits naturally into workshop sessions that focus on replacing broken sections, adapting battery layout, or revising servo placement on an existing front-wheel-drive touring car build.
Other spare parts & accessories
M-08/M-07 Concept A Parts, chassis spare set
300051595€14.29
The M-08/M-07 Concept A Parts set is a dedicated spare tree for keeping compatible chassis cars ready for service. Designed for the M-08 CONCEPT chassis and M-07 CONCEPT chassis, it supplies the A parts needed when original mounting components are damaged, worn or missing after regular RC use. The set contains 1x A parts tree with 24 pieces and provides spares to replace parts on 1 chassis. Its focus is the body mounting area: body mounts and body mount stiffeners restore the connection points that support the shell on the chassis. That makes this set useful when a shell no longer sits correctly, when mounting points have been stressed during running, or when a rebuild calls for fresh hardware from the original parts group. As a model-specific spare set, it stays close to the intended chassis layout instead of relying on mixed universal hardware. The parts suit workshop stock, routine maintenance and targeted repairs on compatible M chassis builds. During a rebuild, the tree format helps keep related components together while damaged pieces are exchanged. For regular RC maintenance, this spare set covers a focused section of the chassis with the exact A parts group named for the M-08 CONCEPT and M-07 CONCEPT platforms. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Manta Ray A-Parts Gearbox Spare Parts Set
300005375€15.49
The Manta Ray A-Parts gearbox set supplies replacement molded components for the 58087 model, centering on the transmission and nearby chassis-mounted assemblies. The black parts come on a single sprue, making each section easy to identify before cutting and positioning during repair or rebuild work. Visible pieces include a large gearbox housing with multiple screw holes, a separate cover or mounting plate, a cylindrical housing element, several hexagonal hub-like parts, and a wider support bracket. This mix supports work in the drivetrain area where aligned mounting points and matching shapes matter. Because the parts are molded as a coordinated set, the geometry across the housing and support sections stays consistent with the intended assembly. The sprue format also helps keep smaller pieces together until they are needed at the bench. This spare parts set suits restoration of a used chassis, replacement of worn transmission-area pieces, or preparation of a stored Manta Ray 58087 for running condition again. It also fits organized workshop stock where model-specific service parts are kept ready for future maintenance.
Other spare parts & accessories
MB-01 Full Ball Bearing Set, chassis accessory
300022026€26.29
The MB-01 Full Ball Bearing Set equips the MB-01 chassis with a complete 18-piece bearing package sized for its rotating assemblies. With 12x 1050 bearings, 2x 1280 bearings and 4x 850 bearings, the set brings together the exact mix needed for a full conversion in one chassis-focused pack. Ball bearings are used at points where shafts and axles rotate, replacing plain bushings with rolling elements that reduce friction during operation. In an RC chassis, that lower drag can support freer drivetrain movement and a more direct mechanical feel across the running gear. The different bearing sizes in this set are arranged to match the MB-01 layout, so the contents are not a generic assortment but a model-specific combination for this platform. The compact format also makes the set useful for routine servicing, a fresh build or a rebuild after wear on existing running parts. Kept alongside other workshop spares, the bearing pack gives a straightforward way to refresh the MB-01 chassis with the full quantity already counted out for the job.
Other spare parts & accessories
MB-01 LD-Parts Fr/Re. Lower Deck, chassis parts
300051725€8.49
The MB-01 LD-Parts Fr/Re. Lower Deck provides the front and rear main chassis sections for the MB-01 platform, giving a model build the structural base that sits at the center of the assembly. These molded chassis parts are intended for replacement, repair or a fresh rebuild where the original lower deck needs to be restored with the correct form and mounting layout. The included parts consist of the main chassis front section and main chassis rear section. In the molded structure, raised side walls, screw mounting posts, recessed fixing areas and formed channels create the attachment points and alignment surfaces needed for surrounding assemblies. This kind of lower deck geometry matters in a chassis build because it determines how major components sit in relation to each other across the front and rear of the platform. The matched front and rear layout also helps maintain the intended fit of connected parts made for the MB-01 chassis. On the bench, these chassis sections suit routine maintenance, accident repair or the revival of a stored model that needs a new structural core. They also work well as workshop spares for MB-01 owners who keep replacement parts ready for ongoing running and rebuild sessions. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Mt.Beetle body mount parts, model accessory set
319000834€12.99
This accessory set provides E Parts body mount components for the 58618 Mt.Beetle and supports accurate replacement work on the body mounting section of the build. The black molded pieces are supplied on a single sprue frame, giving a clear overview of the included shapes before removal and helping keep the parts organized during workshop preparation. Visible on the runner are several distinct molded forms, including bracket-like pieces, rod-shaped elements, a ring-shaped part, a slotted panel and a larger curved housing with round and square openings. That layout helps identify each section during repair or rebuild work and gives model builders the matching geometry needed for the intended mounting area. As a dedicated spare and replacement set rather than a general hardware assortment, it focuses on the specific fit and form required for the 58618 Mt.Beetle. The set works well when an existing chassis needs fresh mounting pieces after wear, loss or damage, or when a stored build is being brought back into running condition with matching replacement parts. It also suits bench stock for ongoing maintenance, where the correct molded components are ready for the next rebuild step. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
R/C Body Mount Hole Patches, RC accessory, 0.5 mm
300054785€6.69
These R/C body mount hole patches add discreet reinforcement where bodyshells take repeated stress. The clear 0.5 mm material strengthens the area around each mounting point while leaving the shell finish visible, so repairs stay unobtrusive on painted or decorated bodies. Each sheet provides 8 patches, giving several mounting points the same treatment in one session or leaving spares ready for later maintenance. The 6.5 mm internal diameter is sized for use on most body mount holes, making the patches a straightforward choice for many R/C bodyshell layouts. Their ring format focuses support around the opening itself, where cracks and widening can start after repeated fitting, removal and running. In workshop use, the patches suit routine bodyshell upkeep before damage spreads further around the post area. They also work well when refreshing a frequently used shell, helping keep mounting holes neat through repeated body changes between running sessions. This accessory is intended for model hobby use and is marked 14 years and up.
Other spare parts & accessories
RC Servo Saver Kit, universal chassis accessory
300050204€6.79
This RC servo saver kit adds an adjustable steering connection for a wide range of chassis layouts while helping reduce shock loads passed into the servo during running. The set is designed for universal use and is listed for many Tamiya platforms including M-06, M-06Pro, F104, F104 Pro II, DT-02 and DT-03, making it a practical choice for repairs, replacements or fresh steering setups. Several servo saver bases are provided so the mounting interface can be matched to different servo makes. The instruction data names base options for Futaba, Sanwa, Acoms, JR and KO, allowing the spline connection to be selected according to the servo in the chassis. Two spring rates are included: S6 strong and S9 weak. The assembly diagrams also show separate configurations for off-road car and racing car use, with S3 or S5 upper parts chosen according to the layout. Mounting hardware covers 3 mm x 12, 2.6 mm x 10 and 2 mm x 10 screw formats, with S1 and S2 spacers assigned to the screw diameter. During setup, the saver arm can be arranged to suit the direction of the servo in the car, and the linkage can be attached by cranked rod or by ball pin depending on the steering system in use. That makes the kit useful both when restoring an older chassis and when refining a custom RC build around the available servo and linkage parts. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Rubber Tire Cement LoVis. 25g, RC tire adhesive
300054511€14.49
Rubber Tire Cement LoVis. 25g is a dedicated CA cement for R/C car rubber tires, made for clean bonding work where a tire bead meets the wheel. The low-viscosity formula flows smoothly into narrow seams, so the adhesive can reach the joint itself instead of sitting on the surface. The bottle contains 25 g of cement and uses a fine nozzle for controlled application in small contact areas. That layout helps when working around the full circumference of a wheel, where steady placement matters more than excess glue. The adhesive is supplied in a bottle with an aluminum bag that limits humidity during storage. In workshop use, that added protection supports more consistent handling when the cement is opened again for later tire maintenance. The source data identifies this as CA cement for rubber tires, giving it a focused role within R/C car setup rather than general household bonding. It fits naturally into bench work before track sessions, when fresh rubber tires are mounted to wheels and the bead needs an even seal. It also suits repair tasks after running, when a lifted section at the joint calls for careful re-bonding with a smooth-flowing adhesive. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Sand Scorcher Rear Guard, model accessory
319335554€10.29
This rear guard is a dedicated model accessory for the Sand Scorcher and is listed for chassis references 58441 and 58452. The included contents are 1 protective bar, giving a clearly defined replacement part for the rear section rather than a mixed hardware assortment. Its focused single-part format helps when a specific rear component needs to be replaced during maintenance, repair or restoration work. The stated fitment to 58441 and 58452 keeps compatibility clear at a glance and supports accurate parts selection for the matching Sand Scorcher versions. Because the set contains one rear protective bar, the part can be kept on hand for workshop stock, planned rebuilds or the replacement of a missing original component. On the bench, this accessory suits routine service work where the rear section needs the correct guard rather than a universal substitute. It also fits restoration projects that aim to return a Sand Scorcher to its intended rear layout with the proper dedicated replacement part. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Servo Saver P-Parts Set for DT-03 and DF-03
300115065€4.49
This servo saver P-parts set is made for compatible DT-03, DT-02 and DF-03 chassis and supplies the shaped components needed when the original steering parts need replacement. The runner format keeps each piece organised and easy to identify before removal, which helps when checking parts against the build or service instructions. The moulded frame shown here carries numbered components, including ring-shaped and bracket-style pieces used within the servo saver assembly. That layout supports careful maintenance because each part stays attached until the moment it is needed. For older kits, workshop repairs, or chassis refreshes, a dedicated spare set like this helps return the steering mechanism to its intended configuration without substituting unmatched pieces. On the bench, the set suits routine servicing, rebuilds after heavy running, or the completion of a partly used kit where original P-parts are no longer available. It also works as a practical stock spare for model collections built around the DT-03, DT-02 or DF-03 platform. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Sponge Tape for Bumper, model accessory, 10-pack
300054430€4.99
Sponge Tape for Bumper is a compact model accessory for fine-tuning fit in RC car setups. Each foam strip measures 150 x 15 x 2 mm and is shaped to sit neatly where a small gap needs to be taken up. Used between a urethane bumper and the body, the tape helps the shell sit more closely against the chassis line, which can support steadier handling on the race track. The same foam material also serves as a spacer on battery holders. Placed between the battery pack and the chassis area, it creates a tighter contact point that helps reduce movement during running. That makes this 10-pack useful not only for body mounting adjustments, but also for routine setup work across multiple cars or repeated rebuilds. The narrow strip format is easy to trim or position according to the space available, while the 2 mm thickness gives a defined layer for controlled spacing. In workshop use, the tape suits quick pre-run checks, replacement during maintenance, or small chassis adjustments before track sessions. It is a straightforward addition for racers who want closer body fit, tidier battery seating and a more dialed-in setup from simple, measurable material changes.
Other spare parts & accessories
Stabilizer Rod Stopper (4), RC chassis hardware
300053827€11.99
The Stabilizer Rod Stopper (4) is a small but important tuning part for RC chassis stabilizer setups. Each collar is fitted onto the sway bar and tightened with a grub screw to hold its position on the rod, so the bar can pivot up and down as intended while lateral movement is kept under control during loaded cornering. The set includes 4 stabilizer collars and 4 grub screws. This layout supports left and right positioning on a stabilizer assembly and gives a clean mechanical stop on the rod itself. The stopper design works as part of the stabilizer system rather than replacing the bar, and it is used with matching sway bar sets on specified chassis. Compatible applications listed in the data include TA06, TA06 PRO, TA06 MS, TB-04, TB-04 PRO, FF-03, FF-03 PRO, TB-03, TB-03 VDS, TA05 ver.II, M-07 CONCEPT, M-08 CONCEPT, TRF502X and DB02, each with the corresponding referenced set. On a touring car sedan setup, this kind of lateral control helps the stabilizer work consistently through repeated laps and setup changes. It suits maintenance, replacement and fine tuning on compatible chassis builds where accurate bar location matters to suspension response.
Other spare parts & accessories
T3-01 Battery Case, chassis accessory, 4xAA
300051610€21.79
The T3-01 Battery Case adds a dedicated 4xAA power option to compatible T3-01 chassis models and gives the Dancing Rider kit an alternative to NiCD, NiMH or Lithium Ion battery packs. The holder is built around a 6V AA layout, with polarity markings in the tray to guide battery placement and a wired connector lead to link the case to the chassis electronics. Inside the assembly, metal battery terminals, springs, screws and the case sections come together as one complete battery compartment. The closure uses a twist-shut cap that can be turned with a coin, keeping the batteries secured once installed. Red and black cable routing is part of the assembly layout, and the connector orientation matters for correct connection to RC equipment. The case is intended for use with 4 AA alkaline or rechargeable batteries and a compatible ESC. Batteries are not included. This accessory suits T3-01 owners who want a separate battery holder matched to the chassis rather than a rechargeable pack format. It fits naturally into maintenance, replacement or conversion work on a Dancing Rider setup, especially when keeping a ready AA-powered option alongside existing running gear.
Other spare parts & accessories
TA-01/02 B-Parts Rear Gearcase, RC spare parts
300050478€18.99
This TA-01/02 B-Parts rear gearcase set brings the rear transmission area back into service with red replacement components made for the TA-01 and TA-02 platform. The set contains 48 pieces, combining molded gearcase sections with the small hardware needed around the assembly, so repair work and parts replacement can stay focused on the correct fit. The included B parts cover the rear gearcase housing area rather than a general mixed assortment, which makes the set useful when a worn, damaged or missing section needs to be replaced with matching components. Alongside the larger red pieces, the contents include screws, metal pins, washers and bushings that support fastening, alignment and mounting within the gearbox assembly. The molded parts show multiple screw locations, shaped edges and dedicated seating points that suit a mechanical housing layout and help keep the rear section properly assembled. On the workbench, this set supports maintenance of an existing chassis, a period-correct rebuild, or the preparation of spare parts for future service. The red finish also keeps the replacement section visually consistent where the original build uses the same color-coded B parts, making it a practical choice for both running repairs and careful restoration work. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
TA-01/02 Front Gear Case, 4WD spare parts, red
300050541€13.99
This spare parts set supplies the red front gear case components for TA-01 and TA-02 4WD models, giving repair and maintenance work the exact housing parts needed for the front transmission area. The A parts tree contains 14 pieces, making it a focused replacement set for restoring the original layout rather than a general assortment. The molded sections shown here cover the front gearbox housing area, with matching red parts that help separate this assembly from other chassis sections during workshop sorting. The set is intended for model servicing where a cracked case, missing section or worn mounting point needs replacement with the correct designated parts. Included metal pins add the small hardware required for the assembly, so the gearbox section can be rebuilt with the supplied connecting elements from this pack alone. On the bench, the clearly grouped A parts support a straightforward check of each housing section before installation. For ongoing TA-01/02 upkeep, this set suits planned maintenance, accident repair and the restoration of older 4WD chassis that need the original front case structure in red. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
TA-01/02/FF-01 D-Parts Body Mount Set
300050482€9.59
This D parts body mount set is made for TA-01, TA-02 and FF-01 model platforms and supplies the core hardware used to position and secure a bodyshell on the chassis. The 22-piece pack combines molded mounting parts with the small metal fixings needed for installation, making it a practical replacement when original body supports are missing, damaged or worn. The set contains 4 long upright posts with a row of adjustment holes, 2 angled mounting arms, 6 screws and 10 metal body clips. That layout supports the usual body-post setup used on compatible on-road chassis, where the shell sits over the posts and is locked in place with clips through the selected holes. The multiple hole positions allow the shell to sit at the required height for the specific bodyshell and mounting point arrangement already on the model. The angled brackets provide the base connection between the posts and the chassis structure. Used during repair, restoration or routine maintenance, this spare parts set helps return a TA-01, TA-02 or FF-01 build to a complete mounting setup. It also suits workshop stock for keeping compatible chassis ready for shell changes, rebuilds and replacement of lost clips or screws after running sessions. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
TA-01/DF-01 Chassis, RC chassis spare part
300335100€23.99
The TA-01/DF-01 Chassis is a molded replacement chassis section for compatible RC model builds, providing the main structural base for reworking a worn frame or completing a repair with the correct platform shape. Its black molded construction uses a ribbed interior layout and a honeycomb reinforcement pattern, giving the part a defined geometry for mounted assemblies while keeping the form focused on mechanical function. The underside shows multiple screw bosses, fastening holes and raised perimeter walls that help position matching components at fixed points across the chassis. An oval cutout on one side and fork-like extensions at the opposite end are integrated into the molding, showing that this is not a generic plate but a chassis section shaped for a specific TA-01/DF-01 layout. The glossy finish comes from the molded surface itself, while the internal bracing and recessed sections are designed around fitment and support. As a spare part, it suits restoration work, replacement after damage, or keeping a compatible workshop build in running condition. On the bench, the chassis gives a clear base for reinstalling drivetrain and mounted hardware in their intended positions. In an ongoing RC collection, it also serves as a practical replacement part for maintaining older compatible models rather than leaving a build incomplete. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
TA-01/TA-02 B-Parts, gearbox rear parts set
300005575€18.99
This replacement parts set is made for the rear gearbox section of TA-01 and TA-02 based models and comes as a black molded B-parts sprue with 7 individual components. The layout keeps related pieces together on one tree, making it easier to identify the required shapes during maintenance or a focused rebuild of the drivetrain housing area. The stated compatibility references 58136, 58146 and 58154, giving clear model numbers for checking an existing build before fitting. As a dedicated B-parts set, this pack suits repairs where the original rear gearbox components are damaged, incomplete or no longer usable. The black finish matches the supplied parts designation, while the molded format supports clean separation of each piece during assembly. The included contents are 1x B parts tree with 7 parts. On the workbench, this set supports targeted servicing without replacing unrelated sections of the chassis. It fits naturally into a repair routine that starts with model-number checking, then moves to part removal, sprue separation and installation in the rear gearbox area of the compatible TA-01 or TA-02 build. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
TA-05/TB Evo.IV B-Parts Body Mount Set
300051242€15.99
The TA-05/TB Evo.IV B-Parts Body Mount set provides the dedicated mounting components used around the body support area on compatible chassis. With 12 black moulded parts in one pack, it covers the component group needed when the original posts, braces or mounting pieces need replacement during maintenance or rebuild work. The set is listed as B parts and is supplied as 1x parts pack, which helps keep chassis servicing focused on the exact section rather than replacing unrelated hardware. Visible components include upright body posts with a series of adjustment holes, shaped brackets, reinforcing plates and small spacers. That layout supports precise positioning where shell height or mounting alignment needs to match an existing setup on a TA-05 or TB Evo.IV platform. This kind of parts set suits workshop stock for routine RC upkeep, accident repair or the completion of an unfinished chassis section. It can be used when restoring the original mounting arrangement after wear, damage or missing hardware, and it keeps the fit of the shell support area tied to the intended B-parts group for these model platforms. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
TA-05IFS/TB-03 F-Parts Hub Carrier (2), chassis part
300051293€7.79
The TA-05IFS/TB-03 F-Parts Hub Carrier set supplies 2 matching chassis components for RC model maintenance, rebuilds and parts replacement. Shaped as front F parts, these pieces are intended for the front area of compatible on-road platforms, where correct mounting points and part geometry matter for a clean fit during service work. Compatibility covers a wide range of Tamiya chassis: FF-04 EVO, FF-03, FF-03 PRO, TA06 MS, TA06, TA06 PRO, TA05 Ver.II, TB-Evo.6 MS, TB-Evo.6, TB-05 PRO, TB-04, TB-04 PRO, TB-03, TB-03 VDS and TT-02 TYP-S. The scope of delivery contains 1 F parts set with 2 components. That broad fitment makes the set useful as a replacement kept alongside regularly used touring car spares, especially when one workshop supports several chassis generations. During routine maintenance, crash repair or a full chassis refresh, a matched pair helps restore the intended front assembly with the correct left and right quantity already in the pack. The black molded parts shown for this set focus attention on fit and function rather than decoration, making them a straightforward choice for keeping compatible RC chassis ready for the next build session or track run. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
TA08 BB Parts Body Mount Bumper Spare Set
319006975€14.99
The TA08 BB Parts Body mount/bumper set provides replacement components for the TA08 platform where the body mounting area and bumper section need to be renewed. Supplied as molded black parts on a sprue, the set focuses on the shaped pieces that connect through formed holes, tabs and attachment points within the chassis assembly. The sprue layout keeps each section identifiable before removal, with the larger curved panel, narrower perforated strips and link-style piece grouped in one frame. This format helps during workshop preparation because each molded section stays in place until trimming begins. Visible part markings on the frame support orientation while matching the pieces to the intended build location. As a spare-parts set rather than a complete kit, the emphasis stays on replacing worn or damaged sections with the correct TA08 BB Parts shapes. On the bench, this set fits naturally into routine maintenance, accident repair or a planned rebuild of a used chassis. It can be kept alongside other running spares so the front structure and body support area are ready to restore when a damaged section needs to be swapped out. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Tamiya Tweezers Straight, precision craft tool
300074004€10.49
Tamiya Tweezers straight bring precise control to detailed model work, with a straight stainless steel body and fine pointed tips that help place small parts exactly where they belong. The slim profile suits close-up tasks at the bench, where careful alignment and a clear view of the work area matter. The pointed ends support delicate handling during assembly, touch-up work and other precision jobs that call for exact placement rather than finger pressure. Stainless steel gives the tool a clean, rigid structure for repeat use, while the black cationic finish adds a durable surface treatment to the long, narrow body. The straight form keeps the handling direct and predictable, which helps when guiding tiny components into narrow gaps or adjusting their position by small increments. On a model bench, these tweezers suit jobs such as setting fine details, moving small pieces into place and handling parts that are difficult to grip by hand. They also fit other craft tasks where accuracy, visibility and a light touch are needed around delicate components.
Other spare parts & accessories
TB Evo.IV/DF-03 Flang.Tube, spare part, 4.6 x 4.7 mm
300051100€4.79
This spare part set supplies 2 collar tubes for selected Tamiya on-road and off-road chassis, using a compact 4.6 x 4.7 mm format that suits precise replacement work during maintenance or rebuilds. The designation TB Evo.IV/DF-03 Flang.Tube 4,6x4,7mm points directly to the specified tube size, helping match the part to the required location in a compatible chassis layout. The set is intended for a wide compatibility range that spans DF-03, FF-04 EVO, FF-03, FF-03 PRO, TA08 PRO, TA07 PRO, TA06 MS, TA06, TA06 PRO and TA05 ver.II. It also fits TB-Evo.7, TB-Evo. 6 MS, TB-Evo.6, TB-05 PRO, TB-04, TB-04 PRO, TB-03, TB-03 VDS, TRF419XR, TRF419X, TRF419, TT-02 TYPE-SR and TT-02 TYPE-S. That breadth makes the pair useful for keeping a parts box aligned with several chassis platforms rather than a single build only. In workshop use, a clearly specified tube size helps when replacing small hardware during servicing, tuning or restoring running condition after wear. The 2 included tubes can be kept as direct replacements for supported chassis or stored as matching spares for future maintenance sessions. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
TC-01/TA-07 Carbon Crossmember Rear RC Part
300054783€15.79
The TC-01/TA-07 Carbon Crossmember Rear adds a focused chassis upgrade to compatible RC touring car builds. Its 2 mm carbon fiber construction spans the left and right rear body mounts, creating a firmer connection that cuts body wobble and gives the rear mounting area a more settled feel during running sessions. The part is supplied with snap pins and 5 mm O-rings for installation at the body mount points. The O-rings are used to cure looseness, helping the mounted shell sit with less play at the connection. A choice of 3 body mount positions adds useful setup flexibility when adjusting shell placement on the chassis. The instruction notes also specify that the crossmember should not contact the body itself, and that instant cement is sold separately for edge treatment. This rear crossmember suits builders refining body mount stability on compatible TC-01 and TA-07 layouts. It works as a compact tuning part for garage setup, shell fitting and track preparation, especially where a more rigid rear mount connection is preferred.
Other spare parts & accessories
Tire Cementing Helper, RC tire gluing tool
300053338€25.49
The Tire Cementing Helper is a dedicated RC workshop tool for bonding tires to wheels with more control at the rim edge. The mounted tire and wheel are placed on the adapter, then light pressure opens a narrow gap between both parts so the cement can flow more easily into the joint. That simple mechanical action helps guide adhesive exactly where the bond is needed during on-road wheel preparation. The set is supplied with an additional adapter for M-chassis use, so it works not only with touring car wheels but also with small diameter M-chassis tires. This makes the tool useful across 2 common RC car wheel formats without changing the basic handling method. The shape is focused on the contact area between rubber tire and wheel rim, where even cement distribution matters most. The tool is intended for manual use during the tire mounting process and supports a steadier workflow when preparing multiple wheel sets. On the bench, the helper suits careful adhesive application before running or display preparation. It can be used when fitting fresh rubber tires, reworking wheel sets, or setting up M-chassis and touring car wheels with a cleaner, more deliberate bonding step. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
TL-01/B A-Parts Chassis Spare Parts Set
300050735€20.49
The TL-01/B A-Parts Chassis set provides a dedicated replacement pack for the TL017B chassis and focuses on the structural section where accurate mounting geometry matters most. Supplied as 3 parts, the set supports repair and rebuild work with components shaped for the original layout. The molded pieces show the technical detailing expected in a chassis section: multiple screw holes, reinforced ribbing, circular bearing seats and shaped cutouts that leave space for adjoining assemblies. This kind of geometry matters during maintenance because the chassis section does more than fill space; it positions connected parts at the intended points and preserves the layout of the model. As a model accessory rather than a complete kit, this set is aimed at replacing a specific area instead of reworking the whole vehicle. On the bench, the set suits planned servicing after wear, damage or a stripped mounting point has made the original section unusable. It also fits ongoing restoration work on a TL-01/B based model where the correct A-parts are needed to return the chassis structure to its intended form. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
TL01 C-Parts Suspension Arm Body Mount Set
300050737€21.29
This spare parts set is made for the TL01 chassis and brings together C-Parts for suspension arm and body mount functions in one matching pack. With 2x C parts and 52 pieces in the scope of delivery, it supports maintenance work that calls for the correct molded shapes rather than improvised substitutes. The set is suited to rebuilds, repairs and parts replacement on an existing compatible chassis. Suspension arm sections and body mount components sit among the parts group, allowing worn, damaged or missing sections to be exchanged while keeping the intended chassis structure. The molded black finish matches the technical look typically used for RC chassis components and makes the different shapes easy to sort during workshop preparation. Because the parts come as a dedicated C-Parts set, the pack stays focused on the exact component family needed for this area of the build. On the bench, this set fits naturally into routine servicing after heavy running sessions, collision damage or long-term wear on a TL01 model. It also helps when restoring an older chassis that needs original-style replacement parts to return mounting points and suspension connections to working order. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
TRF 1510 Sealed Ball Bearings, model accessory
300042365€9.79
TRF 1510 Sealed Ball Bearings add a focused drivetrain upgrade to compatible model assemblies by combining smooth rotation with a serviceable sealed design. The 2 included bearings use rubber seals and low-friction oil inside, creating a compact replacement part that supports clean running in areas where drag and fit directly affect how rotating parts behave. The 1510 format is suited to applications such as touring car bulkheads and M-chassis car differentials, where accurate seating and controlled movement are essential. Rubber seals set these bearings apart from metal-sealed versions because they can be opened for cleaning and maintenance. That makes it easier to remove dirt, refresh lubrication and return the bearing to use without replacing the whole unit. In place of plastic and metal bearings, this design improves parts fit and promotes more efficient rotation in compatible assemblies. On the workbench, these bearings suit routine servicing, drivetrain refreshes and targeted upgrades to worn running gear. In a differential or bulkhead setup, the combination of precise attachment and internal low-friction lubrication supports smoother mechanical action across repeated running sessions. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
TRF 730 Sealed Ball Bearings, model accessory
300042381€8.79
The TRF 730 Sealed Ball Bearings set supplies 2 replacement bearings for compatible model assemblies where smooth, controlled rotation matters. The sealed construction is the defining feature here, because it helps shield the internal rolling elements from dirt while the bearing supports turning shafts or axles inside a compact mechanical layout. This set is focused on maintenance and running efficiency rather than decoration. In workshop use, the 730 bearing size gives a clear specification to match against the required location in a chassis, gearbox or other rotating assembly that takes this format. Fresh bearings can restore cleaner movement in parts that have seen repeated use, and the sealed design is especially useful in areas where dust and fine debris can work into moving components. The 2-piece quantity also suits replacing a pair at the same time when a matching assembly uses 2 bearings together. On the bench, this bearing set fits naturally into routine service, rebuilds and parts planning for RC and scale models. It can be kept as a spare for future repairs or installed during a targeted refresh of compatible running gear, helping mechanical systems turn with less resistance and more consistency. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
TRF Alum. Wheel Spacer, model accessory, 0.75 mm
300054573€8.29
The TRF Alum. Wheel Spacer 0.75 mm Blue is a tuning accessory for touring car R/C models that focuses on one small dimension with a clear setup effect. By adding a 0.75 mm spacer at the wheel mounting point, the tread can be adjusted with more precision, making it easier to refine how the chassis sits across the axle line during setup work. The set contains 8 aluminum spacers in blue, giving a consistent group of matching parts for workshop use, replacement needs or side to side setup changes. Aluminum construction adds rigidity at this contact area, which matters when small measurements are used to influence chassis balance. Rather than changing a major component, this spacer works through a controlled adjustment of wheel position, making it a useful choice when fine tuning a touring car model for a more exact tread setting. On the bench, these spacers fit naturally into routine maintenance and setup sessions for compatible touring car R/C models. They suit builders who compare different chassis responses through measured hardware changes and want a simple way to repeat the same spacing on multiple wheel positions. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
TRF O-Rings 40° Gear-Diff., touring car parts
300042374€6.49
TRF O-Rings 40° Gear-Diff. are dedicated replacement parts for touring car oil-filled gear differentials. The set contains 4 blue ring-shaped O-Rings, arranged for direct use in differential service where this specific 40° specification is required. Their dedicated gear differential design focuses on minimal friction inside compatible oil-filled differential assemblies. In practice, that means the differential can work with less internal drag while transmitting drive through the drivetrain. The ring shape and smooth surface suit sealing and moving contact points inside the differential layout used on compatible touring car models. This is a targeted maintenance part rather than a universal ring set, so the stated compatibility with oil-filled gear differentials is the key fit detail. During workshop maintenance, the 4-piece pack supports a planned differential refresh or replacement of worn rings in an existing setup. The compact format also makes the set easy to keep alongside other touring car service parts for rebuilds, tuning sessions, and routine drivetrain upkeep on compatible RC cars.
Other spare parts & accessories
TRF Universal Shaft BB Set, chassis accessory
300051762€15.29
The TRF Universal Shaft BB Set brings the key running hardware for 2 universal shafts into one focused chassis accessory. With 4 ball bearings, 2 drive shafts and 10 E-rings in 1.2 mm size, it supports drivetrain service work on compatible TRF platforms and keeps the shaft assemblies equipped with the specified retaining parts. This set is intended for use with selected components in the TRF421 range, including item 51760 46 mm lightweight swing shafts, item 51761 46 mm drive shafts for double jointed shafts, item 51763 TRF421X front direct joints and item 51764 TRF421X differential joints. That makes it a targeted choice for builders working on the TRF421 chassis item 42384 and the TRF421X chassis item 42391, where the exact bearing and retention hardware matters. The included ball bearings are assigned specifically to the universal shaft setup rather than to general chassis use. On the bench, the combination of shafts, bearings and E-rings suits planned assembly work as well as replacement during maintenance. It fits naturally into a parts stock for race-oriented chassis service, where compatible driveline components are selected by reference to exact item numbers and shaft length. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
TRF Wrench for Alu.Turnbuckles, RC tool
300042236€14.79
The TRF Wrench for Alu.Turnbuckles is a dedicated RC tool for adjusting aluminum turnbuckle shafts with a compact format that fits naturally into detailed setup work. Its black-finished tip marks it out at a glance from item 42122, the wrench for blue titanium turnbuckle shafts with a silver tip, which helps keep the correct tool close at hand on a busy workbench. The anodized blue handle gives the wrench a clear TRF workshop identity, while ribbed grip sections support controlled finger placement during small steering or suspension link changes. A durable tip section is designed for repeated contact with aluminum turnbuckles, where clean engagement matters during routine maintenance. The tapered body keeps the tool easy to guide into tight spaces around assembled RC chassis and linkages. Printed TRF and TAMIYA RACING FACTORY markings on the handle add a technical finish that matches dedicated tuning equipment. On a setup bench, in a pit bag or beside a parts tray, this wrench supports quick adjustments before running and efficient checks after a session. It suits hobby maintenance where a single-purpose hand tool keeps turnbuckle work direct, organized and easy to identify among other RC tools.
Other spare parts & accessories
TRF417 V5 3.5mm Swing Shaft Cap, chassis part
300051536€5.09
The TRF417 V5 3.5 mm Swing Shaft Cap is a dedicated chassis spare for compatible Tamiya racing platforms, supplied as 5 blades for half shafts in one set. The 3.5 mm size gives a concrete fit reference for maintenance work where matching the stated dimension matters to the driveline layout and the surrounding chassis parts. This spare part is listed for TB-Evo.7, TB-Evo.6 MS, TB-Evo.6, TRF419XR, TRF419X and TRF419 chassis. That model-specific compatibility helps narrow the choice when replacing worn half shaft hardware or preparing a pit box with the correct service parts for these platforms. The set format keeps multiple matching pieces together for routine upkeep, while the dedicated TRF417 V5 designation ties the part to a clearly identified component family rather than a generic hardware option. In workshop use, the blades can be kept on hand for scheduled maintenance or fitted when a compatible chassis needs fresh half shaft parts. The compact 5-piece contents also suit trackside servicing, where having the stated 3.5 mm version ready can simplify replacement work on supported chassis. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
TRF420 F-Parts 4deg HC, RC spare parts
300051641€7.99
TRF420 F-Parts 4deg HC are spare hub carrier parts made for the TRF420 racing car chassis. The set supplies the dedicated carrier shape used at this point in the suspension and steering assembly, with carbon fiber-reinforced resin construction that adds rigidity where bearings, shafts and linkages meet under load. This revised version was developed specifically for the TRF420 platform rather than carried over unchanged from the TRF417, TRF418 and TRF419 era. The updated design has greater resistance to shocks and crashes, which matters most at the hub carrier because this area takes repeated impact from track contact and wheel-side forces. The 4 degree specification defines the geometry of the part itself, while the mirrored pair format matches left and right installation. Upper and lower flanged tubes are identical, which keeps the hardware layout consistent when servicing the assembly. These parts are designed for use with 3 mm diameter shafts and work with cars using TRF420 D Parts suspension arms. On a race chassis, hub carriers are often replaced after heavy contact or updated during setup changes, so a dedicated spare set keeps maintenance focused and the car ready for the next rebuild. The precise molded openings and mounting points support clean installation alongside the matching suspension components.
Other spare parts & accessories
TRF420X Stiffener Nut, model accessory, blue
319803402€13.79
The TRF420X Stiffener Nut set brings a clearly specified hardware option to model maintenance, replacement and setup work. With 5 blue nuts in the pack, the set gives a concrete match for builds or repairs where the TRF420X designation is the key reference and small fastening parts need to be identified quickly on the bench. The blue finish adds a visible sorting cue when hardware is laid out beside other screws, spacers and fittings, helping keep similar small parts easier to separate during assembly. The nut format points to a threaded fastening role rather than a decorative add-on, so the set suits practical workshop tasks built around securing or replacing existing hardware. The 5-piece count also supports repeated service work, whether one nut is needed for a direct replacement or several are prepared for ongoing maintenance across the same model platform. On a work surface, these nuts fit naturally into parts trays, setup stations and repair sessions where compact hardware is handled one piece at a time. For model builders keeping TRF420X-specific spares ready, the set provides a straightforward stock of matching fastening components in a distinct blue finish. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
TRF421 Rear Body Posts, RC spare parts
300051740€10.19
TRF421 Rear Body Posts are RC spare parts for the rear bodyshell mounting area, intended to restore the correct shell position on a compatible TRF421 setup. When the rear mount has worn, bent or been damaged in use, replacing these posts helps return the bodyshell to its proper height and alignment so the chassis can be prepared with the intended fit. As BB parts, they belong to a specific TRF421 parts grouping rather than a universal hardware assortment. That makes them a focused choice for maintenance, repair and setup work on the matching platform. Rear body posts handle a precise task at the back of the chassis: they support the shell where mounting position influences how the bodyshell sits over the rear section and how cleanly the mounting holes line up. In regular bench work, spare posts are practical to keep on hand for rebuilds after contact, routine wear replacement or setup refreshes before the next run. The compact format suits a pit box, workshop drawer or parts case, where dedicated replacement components help keep RC maintenance organised. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
TRF421/X 3x20mm Damper Shaft, model spare part
319803496€6.19
The TRF421/X 3x20mm Damper Shaft set is a dedicated spare part for suspension servicing on compatible model setups. With a 3 mm diameter, 20 mm length and 2 shafts in the pack, it provides the core replacement component needed when a shock unit is being rebuilt or refreshed. Used inside the damper assembly, each shaft forms the moving element that guides the shock through its travel. Replacing a worn or marked shaft can help restore smooth damper action and keep the suspension working evenly across a matched pair. The compact 3 x 20 mm format also makes this set a practical choice for keeping key maintenance parts ready between rebuilds, whether the workbench is set up for routine servicing or for preparing a chassis after repeated running sessions. For hobby maintenance, a dedicated spare like this avoids replacing complete shock assemblies when only the shaft needs attention. The 2-piece pack fits naturally into parts storage for suspension rebuilds, setup checks and ongoing chassis care. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
TRF421X Aluminium Chassis Plate, chassis part
300051759€99.99
The TRF421X Aluminium Chassis Plate is a dedicated lower deck for the TRF421X platform, bringing a model-specific aluminium base into rebuilds, maintenance work and chassis updates. As a single replacement part, it addresses the central structure of the car where the main platform layout begins, making it relevant when a worn or damaged lower section needs to be exchanged. Compatibility is stated for both the TRF421 and TRF421X chassis, which keeps this part closely tied to those 2 racing platforms rather than a broad universal fit. The supplied quantity is 1 aluminium chassis plate, giving a clear match for targeted spare-part planning. The data also states an installation condition for TRF421 use: this aluminium sub-deck and the corresponding motor mount are used as a set when this deck is fitted to that chassis. That requirement matters for workshop preparation because it defines the matching hardware arrangement for the conversion. On the bench, this lower deck suits routine servicing, accident repair and planned chassis refresh work where the main plate is the part being replaced. It also fits organised spare-part storage for TRF421 and TRF421X running gear, where exact platform compatibility is more useful than a generic chassis component. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
TRF421X Cooling Fan Post, model accessory, black
313451594€29.49
The TRF421X Cooling Fan Post is a dedicated model accessory for RC setups that need a defined mounting point for a cooling fan. Its black finish gives the part a restrained technical look that sits neatly within detailed chassis layouts, while the stated weight of 20 g adds a concrete reference for parts selection and setup planning. This accessory is identified by the exact TRF421X Cooling Fan Post designation, which helps when matching replacement parts during maintenance or when refining an existing build with the correct hardware. The part belongs to the models and accessories range and is listed within model supplies, placing it clearly in the workshop side of the hobby rather than as a complete vehicle or kit. The black colour keeps the appearance consistent with many competition-focused assemblies where visible hardware is kept understated. On the bench, this component fits naturally into rebuilds, repairs and specification-led upgrades where the right mounting part matters as much as the fan itself. It also suits organised spares storage, where the exact name and 20 g reference make selection easier during ongoing chassis work. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
TRF421X Front Stiffener Carbon, model part
313404160€5.99
The TRF421X Front Stiffener Carbon is a dedicated model part for the TRF421X platform, built around a clearly defined front-end role and a carbon material specification. Its designation points directly to the intended chassis family, which helps keep replacement and setup work aligned with the correct model rather than relying on universal parts. As a front stiffener, this component belongs to the structural area at the front of the chassis and is intended for targeted maintenance, repair or parts planning within that exact platform. The carbon construction gives the part a distinct material profile that suits model builders who sort components by function and specification. Because the data identifies this as a single named part rather than a general accessory set, the focus stays on exact fit within the TRF421X designation and on clear workshop organisation. This kind of chassis part fits naturally into bench work where a build is being refreshed, maintained or prepared with the correct front-end components. It also suits spare-parts storage for model setups that are managed by platform name, making the TRF421X designation and the front stiffener function easy to recognise at a glance. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
TRF421X Piston 4 Holes 4x1,2 BLK, model part
319803567€8.19
TRF421X Piston 4 Holes 4x1,2 BLK is a dedicated model spare part for suspension servicing and setup work. The pack contains 4 black pistons, giving a consistent set for replacing worn internals or preparing matching damper builds where equal specification across all corners matters. The 4-hole design in a 4x1,2 configuration defines how shock oil passes through the piston during compression and rebound. That makes this part relevant when damping response needs to be kept consistent after maintenance or changed with a specific piston layout already in mind. The exact TRF421X naming also helps separate this version from other piston types during parts storage and workshop preparation. As a compact tuning and replacement component, it fits naturally into routine rebuilds, damper refreshes and planned setup changes where the internal shock specification is chosen deliberately rather than left mixed. On the bench, the set suits organised rebuild sessions where all 4 dampers are being refreshed together. It also supports trackside maintenance when a matching piston set is needed to return a compatible chassis to an even suspension setup after wear or damage. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
TRF421X Upper Arm Nut Set Blue RC Spare Part
319803565€22.89
The TRF421X Upper Arm Nut set in blue is a focused RC spare part for suspension maintenance where the exact fastening point matters. With 4 matching nuts in one pack, it supports clean replacement work on the upper arm position named in the designation and keeps the hardware consistent across the assembly. The blue colour gives the set a clear visual distinction during bench work, making the nuts easier to separate from other small fasteners in a parts tray or toolbox. That matters most during rebuilds, routine servicing or when a missing fixing needs a like-for-like replacement instead of a generic alternative. Because the data identifies these specifically as TRF421X upper arm nuts, the set is suited to precise parts management within that model platform rather than general mixed hardware use. This kind of small component often becomes important during suspension work, where secure fastening and correct placement keep the assembly process moving without interruption. Kept as workshop stock or added to a race-day spares case, the 4-piece set covers the named nut type in a compact format that is easy to store and quick to reach when maintenance is underway. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
TRF421X/TA-08 Urethane Bumper RC Spare Part
316275083€7.69
The TRF421X/TA-08 Urethane Bumper is a dedicated RC spare part for the front end of compatible chassis builds. Its wide curved form, shallow centre dip and 2 mounting holes match the shape needed for direct placement, giving the front section a defined cushioning element where contact is most likely to occur. Made from urethane with a foam-like structure, the bumper adds a light impact-absorbing layer without introducing unnecessary complexity to routine maintenance. The textured surface and tabbed mounting points show its purpose clearly: this is a shaped replacement part rather than a universal pad that needs trimming or adaptation. That makes it useful for rebuilds, worn-part replacement and keeping a chassis configuration consistent between running sessions. The compact format also stores easily in a pit box or parts case alongside other maintenance essentials. On a workbench, the bumper supports straightforward servicing when a front-end contact part needs to be swapped. In regular RC use, it helps keep the intended front bumper setup in place for continued running with the matching TRF421X or TA-08 layout. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
TT-01 Alum.Bumper Stopper, chassis accessory
300053682€13.99
The TT-01 Alum.Bumper Stopper is a chassis accessory for TT-01 Type-E, TT-01 Type-ES and TT-01D Type-E platforms, built to reinforce the front bumper area with a 2 mm aluminium plate. Mounted at the bumper section, it helps the urethane bumper keep its form while the chassis is in use, giving the front end a more controlled structure. The shaped plate uses a dedicated mounting layout for the listed TT-01 variants instead of a generic fit. Its aluminium construction brings a rigid support part to a section that regularly absorbs contact, and the blue anodized finish adds a clear tuning detail to the front of the chassis. The part is supplied as a bumper stopper, not as a full bumper assembly, so it works as a focused replacement or upgrade within an existing TT-01 setup. On a bench build, the stopper suits refresh work on a worn front end or a more detailed custom chassis configuration. Once installed, it supports the bumper section during regular RC running while keeping the visual style of the car clean and technical. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
TT-01 Bathtub Chassis, chassis part, tub frame
300051001€14.49
The TT-01 Bathtub Chassis is a chassis part for TT-01 builds, formed as a black molded tub frame that creates the main lower section of the model. Its one-piece layout brings the mounting areas, compartment sections and structural walls together in a single base, giving the assembly a defined foundation for the rest of the running components. The molded construction shows multiple screw points, reinforcing ribs and raised posts that help position attached parts in the intended locations. Formed front and rear mounting areas support the chassis layout at both ends, while the central cross brace adds another structural element within the frame. The internal shape also provides dedicated recessed sections for component placement, which helps keep the build organized during repair or reassembly. As a spare part, this chassis is suited to replacing a damaged lower frame while preserving compatibility with the TT-01 platform. On the workbench, the tub frame serves as the starting structure for a rebuild, with the molded sections helping sort where major assemblies sit within the chassis. It also fits parts stock for ongoing TT-01 maintenance, where a fresh lower frame can return a used model to a clean, correctly based configuration. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
TT-01/E B-Parts, chassis spare parts set
300051003€21.29
The TT-01/E B-Parts set is a dedicated spare parts pack for the TT-01 TYPE-E chassis, combining suspension arm and body mount components in one replacement set. With 42 pieces in the scope of delivery, it supports repair work that restores key chassis connection points and shell mounting positions with parts matched to this platform. The set is supplied as 1x B parts tree and is intended for chassis TT-01 TYPE-E as stated in the product data. Suspension arm sections handle the wheel-side linkage points that guide movement at the chassis, while the body mount parts provide the posts and holders used to position the bodyshell on the car. Keeping these parts grouped in one pack helps when wear, damage or a rebuild calls for the original component shapes rather than improvised substitutes. This spare parts set suits workshop stock for ongoing TT-01 TYPE-E maintenance, whether a chassis is being repaired after running sessions or rebuilt around fresh mounting points. It also fits planned restoration work where suspension connections and shell supports need to be replaced together to return the model to its intended layout. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
TT-01/E/R Servo Horn Saver Set, chassis parts
300051005€6.79
The TT-01/E/R Servo Horn Saver Set supplies dedicated chassis parts for several Tamiya on-road and drift platforms, with compatibility listed for TT-02B, TT-02FT, TT-02RR, TT-02D, TT-02, TT-01D TYPE-E and TT-01 TYPE-E. As a focused replacement set for the steering connection area, it helps keep servicing work aligned with the original layout of the compatible chassis. The scope of delivery contains 1x P parts sprue with 10 pieces. The moulded components are supplied together on the sprue, which helps identify the matching parts before removal and installation. The set is intended for the servo horn and saver section, where the steering servo transfers movement into the chassis linkage through correctly shaped mounting parts. Using a dedicated set avoids mixing unrelated shapes when worn or missing pieces need to be replaced on supported platforms. This kind of parts set suits routine workshop use, planned chassis refreshes and targeted repairs after heavy running sessions. Kept alongside other maintenance spares, it gives compatible TT-01 TYPE-E and TT-02 based builds a direct source for steering hardware when the original servo saver assembly needs attention. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
TT-01D/R/E B-Parts, RC spare parts set, 42 pieces
300051217€24.49
This B parts set is made for the TT-01D TYPE-E platform and brings 42 replacement pieces together in one pack for targeted chassis repairs. The sprues combine suspension arms and body mount sections, making it easier to restore key mounting points after wear, impact, or a stripped thread has taken a car out of use. The molded parts layout groups mirrored left and right components, along with smaller brackets, linkage-style pieces and structural sections that support accurate replacement work. Keeping these parts in the original molded form helps with identification before removal from the sprue and allows the needed section to be selected without sorting through mixed loose hardware. As a dedicated spare parts set rather than a general assortment, it matches the TT-01D/R/E family named in the data and focuses on the areas most often involved in chassis rebuilds. On a bench between running sessions, the set supports quick replacement of damaged arms or mounts so the model can return with its intended structure intact. It also fits neatly into a parts drawer for routine maintenance, where having the correct B tree ready can shorten downtime when a specific chassis section needs to be renewed. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
TT-01E Urethane Bumper, RC spare part
306275067€5.99
The TT-01E Urethane Bumper is a model car spare part shaped for the front end of chassis 58407. Its molded urethane form follows the contour of the mounting area, creating a clean interface between the chassis nose and the surrounding front structure during repair or parts replacement. The gray bumper piece uses a dense foam-like urethane material with an irregular rectangular profile, rounded corners and 2 recessed openings. Those cut-ins align the part with the chassis mounting zone and help position the bumper evenly when an existing piece has worn down or gone missing. As a dedicated TT-01E replacement rather than a universal pad, it is intended to match the original layout of this chassis type. The compact form also makes it a practical workshop spare to keep on hand for routine maintenance of a running model. This component fits naturally into rebuild sessions, front-end refreshes and chassis servicing where the original bumper needs to be exchanged for a matching part. In a parts box for RC maintenance, it covers a specific wear area with the correct shape instead of relying on improvised foam inserts. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
TT-02 D Parts Motor Mount, chassis spare parts
300051530€6.49
The TT-02 D Parts Motor Mount is a chassis spare-parts set for the TT-02 platform, supplied as 1x D parts with 13 pieces. It is intended for the motor mount area and matches a wide group of compatible chassis versions, making it a practical choice when a build needs the correct replacement section rather than a universal workaround. Compatibility covers TT-02, TT-02B, TT-02D, TT-02FT, TT-02RR, TT-02 TYPE-S and TT-02 TYPE-SR chassis. The molded parts are presented as a dedicated D-parts tree, which helps keep part selection clear during maintenance and rebuild work. For RC model owners who keep several TT-02 variants in service, that shared fit can simplify spares storage and reduce guesswork at the bench. The 13-piece count also points to a defined component group for this area of the chassis rather than a mixed assortment of unrelated hardware. This set fits naturally into repair, restoration and routine upkeep of compatible TT-02 vehicles. It can be used when refreshing a worn motor mount section, replacing damaged original parts, or preparing a chassis for its next running session with the correct matching components from the TT-02 family. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
TT-02 Lower Deck, chassis frame for TT-02 models
300051532€8.29
The TT-02 Lower Deck is the main tub frame chassis for a wide range of TT-02 platforms and provides the molded base that carries the running gear layout of the car. As the central lower structure, it supports the installation of drivetrain parts, suspension assemblies and electronics in the intended chassis arrangement, making it a practical replacement part for repair work or a new build based on an existing TT-02 setup. This lower deck is specified for TT-02, TT-02B, TT-02D, TT-02FT, TT-02RR, TT-02 TYPE-S and TT-02 TYPE-SR chassis. The scope of delivery contains 1 tub frame chassis. The molded construction uses a deep central tray, raised side walls, reinforcing ribs and multiple screw posts to create the structural base for the vehicle layout. Mounting areas at the front and rear connect with the surrounding mechanical assemblies, while the central section leaves room for the internal chassis components used in the compatible platforms. In the workshop, this part suits rebuilds after wear, damage or heavy use, and it also supports parts-based TT-02 projects that need a fresh lower frame. For maintenance benches, spare-parts storage or a full chassis refresh, the lower deck restores the correct foundation for the compatible TT-02 family. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
TT-02 Lower Deck, chassis part, hard black
300054926€11.79
The TT-02 Lower Deck in hard black gives TT-02 platform builds a rigid main chassis base with a clean, neutral finish. Made from glass fiber-reinforced material, this lower deck is shaped for use as the central tub section in compatible chassis cars, where stiffness and accurate fit matter during assembly and setup. This version adds a black colour variation to the hard lower deck previously offered in white and blue. The hard specification is intended to increase rigidity in the chassis structure, which can help a model make fuller use of its suspension and drivetrain settings once the running gear is installed. As the main lower section of the chassis, the deck forms the mounting foundation for the surrounding mechanical parts and keeps the layout consistent across maintenance, rebuilds and tuning changes. The single lower deck is supplied as 1 piece. Compatibility covers TT-02, TT-02B, TT-02D, TT-02RR, TT-02 Type-S and TT-02T chassis cars. In workshop use, it suits a worn original part, a fresh rebuild or a colour-coordinated update where the black base is intended to sit neatly with the chosen bodyshell and livery. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
TT01E/R/D D-Parts, battery holder motor mount
300051319€13.49
The TT01E/R/D D-Parts set is a dedicated replacement pack for TT-01D TYPE-E and TT-01 TYPE-E chassis builds, centered on the battery holder and motor mount area. With 16 molded components in black, it provides the specific parts needed when these sections show wear, damage or loss during maintenance. The set is supplied as 1x D parts group and is intended for exact compatibility within the listed TT-01 variants rather than as a universal RC fitting. That makes it useful for restoring original mounting geometry in the chassis, especially where the battery holder, motor mount and related structural pieces need to be brought back into service. The molded format also keeps the individual shapes consistent across the full set, which matters when replacing interrelated chassis sections. On the bench, this spare pack fits naturally into routine RC upkeep, whether a drivetrain area is being refreshed, a damaged mount is being replaced or a stored chassis is being returned to running condition. It also serves as a practical stock part for TT-01 owners who maintain compatible platforms and want the correct D section ready for future repairs. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Universal Toolkit, model tool set for 1:10 kits
300050038€4.49
This universal tool set brings together the core hand tools and small hardware often needed around 1:10 model kits. The set contains 2 Allen keys, 4 grub screws and 1 cruciform wrench, creating a practical bench companion for assembly, adjustment and routine maintenance work. The cross-shaped wrench is suited to repeated fastening tasks where a firm hand position and quick tool changes matter. Its 4 socket ends place several sizes in one tool, so common nuts and fittings can be reached without switching between separate drivers. The 2 L-shaped Allen keys are useful for hex socket screws set deeper into components, where the short and long arms help with leverage and access. The 4 grub screws add spare fastening hardware for small locking points that need replacement or readjustment. Used beside a fresh kit build or during later servicing, the set supports the small, precise jobs that keep a model running cleanly. It fits naturally into a workbench routine for chassis tuning, hardware checks and part changes on 1:10 models, and the included mix of tools keeps the most-used essentials together in one place. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Urethane Bushing, model accessory, 10-piece set
309805922€4.19
This set of 10 urethane bushings is made for model maintenance where small replacement parts need to match in shape and material across the whole pack. The compact cylindrical pieces are supplied as loose components, making them straightforward to keep with workshop spares or to allocate to a specific repair job. The product data identifies the set as MB23 / TB-02, which helps place it within an existing parts list or compatible model setup without relying on guesswork. The image shows 10 white porous cylinders arranged as individual inserts, highlighting their uniform size and consistent cut. That even format matters when several matching bushings are needed for the same mechanism or when older parts are being replaced together rather than one by one. Urethane construction also gives this pack a clearly defined material specification instead of a generic mixed-parts description. In practical use, the set suits routine servicing, parts replacement and keeping spare inserts on hand for later workshop tasks. The 10-piece quantity also supports repeated maintenance cycles, whether the aim is to refresh a current build or keep matching bushings available for future model work.
Other spare parts & accessories
Wheel Spacer/Blue (8), RC accessory set
300053646€12.99
This wheel spacer set adds a precise tuning option to compatible RC chassis by shifting wheel position with small, measurable changes. The set contains 8 blue spacers and supports tread adjustment through 2 thicknesses, with 4 pieces at 0.5 mm and 4 pieces at 1 mm, so setup changes can be made in fine increments instead of one large step. The ring-shaped parts are suited to maintenance, replacement and chassis tuning where wheel fitment needs a controlled offset. Their compact washer-style form keeps the function straightforward: each spacer sits in the wheel mounting setup to alter position by the stated thickness. On DT-02 chassis, DT-03 chassis and DT-03T chassis, these spacers can only be used for the rear wheels. Scope of delivery: 8 spacers. The set works well as a small workshop supply for routine servicing, for rebuilding a used chassis, or for testing different rear wheel positions during setup changes. The blue finish also makes the individual spacers easy to identify when sorting tuning parts with other RC hardware and replacement components. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
WT-01 A-Parts Gearbox for RC Model Chassis
300005713€13.99
The WT-01 A-Parts Gearbox supplies the main housing pieces for compatible RC model chassis builds, with 2 mirrored components arranged on a single sprue for clean identification before removal and assembly. The molded form shows the structural shell that surrounds the transmission area, with circular openings, recessed sections and shaped outer contours that match the mechanical layout these parts are made to serve. Each piece is injection-molded as a dedicated left or right half, allowing the gearbox area to be rebuilt with matching geometry rather than improvised substitutes. The visible posts and screw locations support accurate positioning during installation, while the enclosed housing format helps organize the internal drivetrain section within the chassis structure. This set is listed for 58231, 57825 and 58514, making it a focused replacement choice when one of those specified models needs original A-parts again. On a repair bench, the 2-part layout keeps the job straightforward: remove the sprue parts, prepare the mounting points and return the transmission case to its intended form. For restoration work, maintenance or keeping spare chassis components ready, this gearbox set covers the essential shell pieces without adding unrelated hardware. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
XM-01 B Parts Body Mounts, spare parts set
300051747€8.79
The XM-01 B Parts Body Mounts set provides the shaped structural pieces used to position and support the bodyshell on an XM-01 chassis. Moulded in black and laid out as a dedicated spare parts group, the set focuses on the mounting area where shell height, placement and attachment points need to line up cleanly with the rest of the build. Two main mounting plates form the core of the set, each with multiple screw holes and reinforcing ribs that guide stable installation. Long L-shaped support arms add a row of adjustment holes, allowing the mounting position to be changed in measured steps rather than by guesswork. A cross brace links the assembly with an additional connection point, adding another structural element to this replacement group. These are workshop spares intended for repair, maintenance or a fresh rebuild when original parts are worn, damaged or missing. Used during chassis servicing or parts replacement, this set helps return the shell mounting area to its intended layout so the bodyshell can sit in the correct position. It suits bench work focused on restoring fit and attachment rather than cosmetic changes, and it keeps an XM-01 build supplied with the specific parts needed for this section. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
XV-02 B Parts Bumper Set for XV-02 Chassis Cars
300051697€11.29
XV-02 B Parts Bumper is a dedicated replacement set for XV-02 chassis cars, bringing the specified front and rear bumper hardware together in one pack for maintenance, rebuilds and chassis refresh work. The set focuses on the bumper and body-mount area, where repeated running, body changes and routine workshop handling can call for exact matching parts. The contents are clearly defined: 1 front bumper, 2 front body mounts, 1 front stiffener, 1 rear bumper, 2 rear body mounts, 1 rear stiffener and 1 transponder stay. That 9-piece layout covers both ends of the XV-02 platform and keeps the front and rear mounting points aligned with the listed chassis fitment. The body mounts and stiffeners sit alongside the bumpers rather than as unrelated extras, so the set supports coordinated replacement across the same structural area. The transponder stay adds the specified mounting part for race or timing setups where that fixture is needed. Used during repair, scheduled maintenance or a fresh chassis build, this parts pack helps restore the intended XV-02 configuration with components named for the exact platform. It also suits keeping workshop spares on hand for track days, club running sessions or rebuilds after contact, where matching bumper and mount parts save time compared with piecing together separate replacements.
Other spare parts & accessories
Molybdenum Grease 10g, model lubricant tube
300087022€6.991 kg = €699.00
Molybdenum Grease 10g is a model lubricant designed for moving assemblies where precise application and controlled coverage matter. The paste-like grey-black grease comes in a tube with a pointed nozzle, making it easier to place a small amount directly onto contact areas while working on model vehicles at the bench. The formulation is identified for use as a lubricant for model vehicles, giving maintenance work a clear technical focus rather than a general household use. Its density is listed as 0.96 ±0.03 g/ml at 15 °C, and the kinematic viscosity is specified as above 20.5 mm2/s at 40 °C. The grease is insoluble in water and has a slight inherent odour. A drop point above 200 °C and a flash point above 200 °C add further material data for hobbyists who maintain drivetrains, rotating shafts and other loaded contact points. In practical use, the narrow nozzle supports careful servicing on compact mechanisms where grease needs to reach a specific spot instead of the surrounding structure. It suits routine workshop tasks such as refreshing lubrication on gears, bearings, joints and shafts in model vehicles, helping keep maintenance neat and targeted. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
4-7mm Ground Clearance Gauge, setup tool
300022009soon available again
This aluminium ground clearance gauge brings a precise reference to RC car setup work, with a stepped measuring range from 4 mm to 7 mm. The blue anodized body and clearly marked values make each height point easy to identify at the bench, helping setup changes stay consistent across repeated checks. The stepped form is designed for direct measurement against the underside of the chassis, so ride height can be checked against fixed increments rather than judged by eye. Markings at 4, 4.5, 4.8, 5, 5.2, 5.4, 5.6, 5.8, 6, 6.2, 6.5 and 7 mm provide multiple reference points for fine tuning. The machined aluminium construction gives the tool a solid, precise feel in hand, while the compact shape fits easily into a pit box, tool case or setup station. On a workbench before a run, the gauge supports quick confirmation after spring, damper or preload changes. Between sessions, it helps keep left and right setup checks aligned to the same measured clearance, making repeatable tuning work easier to track over time.
Other spare parts & accessories
CC-02 J-Parts Body Mounts, chassis spare parts
300051634soon available again
CC-02 J-Parts Body Mounts provide a direct spare-parts solution for the CC-02 chassis platform, combining body mounting pieces and suspension arm components in one matched set. The 2 included J Parts sprues support repair work that restores key connection points across the chassis while keeping the replacement process focused on the correct component group. The molded parts are supplied as black sprue frames, with mirrored left and right layouts that make the individual sections easy to identify before cutting and fitting. Multiple mounting bars, linkage-style pieces and bracket forms are arranged to serve structural positions within the chassis assembly. Because the set covers both front and rear areas, it suits maintenance jobs that go beyond a single broken mount and need a coordinated replacement across more than one section. Compatibility is stated for CC-02 chassis models, keeping the fit aligned with that platform rather than generic off-road frames. On the bench, this set supports routine restoration after wear, damage or a partial teardown of a CC-02 build. It also helps keep a running chassis ready for the next repair session by putting the relevant mounting and arm components in one dedicated spare-parts pack.
Other spare parts & accessories
DF-01 B-Parts Rear Gear Case Spare Parts
309005318soon available again
The DF-01 B-Parts Rear Gear Case is a replacement sprue for the designated rear transmission housing area of a DF-01 model. The black injection-molded parts are supplied attached to the frame, which keeps each section identifiable before removal and helps separate the individual shapes during repair or rebuild work. Visible on the sprue are multiple structural components for the rear gear case section, including housing forms, circular and cross-shaped pieces, mounting holes and smaller connectors. This format supports a direct parts-based approach when an existing assembly needs the specific B Parts group rather than a full rebuild set. The molded layout also makes it easier to compare each section against the matching area of the vehicle during maintenance. Used as workshop spares or as a replacement during restoration of a DF-01 chassis, this set focuses on the rear gear case area named in the designation. It suits planned servicing, the exchange of worn sections, or the completion of an incomplete chassis where the original B Parts sprue is missing. Batteries are not included. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Fluorescent Antenna Pipes, RC model accessory
300053132soon available again
These fluorescent antenna pipes add a clear visual marker to an RC model by lifting the antenna into bright orange, pink, green and yellow. The strong colours stand out well while driving, making the model easier to identify at a glance during fast laps, club sessions or side-by-side running. The pack contains 4 antenna pipes and is suited to colour changes, replacement use or keeping several builds ready with different antenna finishes. Each pipe is a simple add-on for the antenna position, where the bright tube creates a more visible reference point above the bodyshell. The included antenna caps complete the set and provide the small finishing parts needed for installation. As a compact tuning accessory, the set focuses on visibility and appearance rather than changing the drive system or chassis layout. On indoor tracks, outdoor tarmac or busy practice sessions, the fluorescent colours help the antenna remain easier to pick out against the background and among other running models. The different colour options also support matching the antenna to body graphics, race colours or workshop spares for ongoing RC maintenance. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Gearbox B Parts, RC spare parts for M.Pumkin
300005276soon available again
This B Parts gearbox set is made for M.Pumkin and Lunch Box and provides the molded components needed for work on the transmission housing area. The black sprue carries matched structural pieces that suit replacement, restoration, or a fresh rebuild when worn or damaged gearbox sections need to be exchanged. The visible layout shows 2 mirrored casing halves, a central round cover piece, and 2 smaller circular discs, all molded as a coordinated parts tree. That arrangement helps keep related components together before removal and gives a clear overview of the shapes used in the assembly. The larger shells feature cylindrical tower forms and ribbed circular housing details, indicating their role as enclosing and supporting mechanical internals. Because this is a model spare-parts set, it is intended for an existing compatible vehicle rather than as a standalone build. On the bench, this set supports focused repair work on the gearbox section of the compatible RC model. It also suits keeping a replacement sprue on hand for maintenance, especially where a rebuild calls for matching housing geometry instead of improvised substitutes.