RC tuning parts
Higher, faster, further with Tamiya tuning parts. Tune your RC vehicles just the way you want them. If you would like to find out more, you can read more here.
RC tuning parts
0.4 Module Pinion Gear Set, RC accessory, 28/29T
300053262€18.99
This 0.4 module steel pinion gear set brings precise gearing changes to compatible RC chassis, with 28T and 29T pinions that allow a finer adjustment of the transmission ratio than broader tooth-count steps. The steel construction and compact geared form suit drivetrain setups where efficient transfer of motor output matters on the track. The set is supplied as 6 parts: 2 pinion gears, 3 set screws and 1 hex key for installation. The pinions are intended for use with separately available 0.4 module spur gears, and the data names specific pairings for several chassis families. FF-03 and FF-03 PRO use it with 54227, TB-03, TB-04 and TB-04 PRO use it with 54055, TA05 Ver.II uses it with 53857, and F104 or F104W use it with 54166 plus 53104 or 53900. F104PRO II uses it with 54166. Compatible chassis named in the data include F104PRO II, F104 Ver.II PRO, F104W, F104, FF-03, FF-03 PRO, TA05 Ver.II, TB-04, TB-04 PRO, TB-03, TRF103, TRF102 and TRF101. In workshop use, the two tooth-count options support quick ratio changes between runs, while the included hex key helps with fitting and adjustment at the bench or trackside. Warning! Not suitable for children under 14 years.
RC tuning parts
04 Spur Gear 93T/104T, RC gear set, 0.4 module
300053900€9.79
The 04 Spur Gear 93T/104T set is a drivetrain tuning part for RC chassis that use 0.4 module gearing. With 93T and 104T spur gears in one pack, it supports finer ratio selection than the standard 0.6 module gear and opens up smaller adjustment steps when acceleration and running efficiency need closer control. Each gear uses a fine tooth profile that changes how the spur and pinion mesh, making this set useful when a standard ratio jump is too broad for the setup. Molybdenum in the gear material is specified to reduce friction resistance at the contact point, which supports smoother power transfer through the drivetrain. The set is intended for F103 and C Car chassis and is used together with 0.4 pinion gear #53101. That compatibility matters when preparing a chassis for different track layouts, motor characteristics or rolling conditions where a small gearing change can alter response. On a bench setup, the 2 tooth counts make back-to-back comparison straightforward because the gearing can be changed with a direct spur swap. On the track, that means a setup can be tuned toward sharper pull out of slower sections or toward a more efficient running balance across a full session.
RC tuning parts
1:10 Touring Car Short Springs II, RC spring set
300054797€19.99
The 1:10 Touring Car Short Springs II set brings finer suspension tuning to touring car setups by adding 3 short spring rates that sit alongside the existing range. Each pack contains 6 black coil springs arranged as 3 pairs, giving a direct way to alter chassis response for changing track conditions and different driving inputs. The set includes 2 Super Hard springs with white marks, 2 Medium-Hard springs with gold marks and 2 Medium-Soft springs without a color mark. That spread broadens the choices beyond the Hard, Medium and Soft options in Item 42168, making it easier to narrow in on a more exact setup. The color coding helps keep spring pairs sorted during rebuilds, test sessions and repeated suspension changes. As short springs, they are intended for touring car short damper layouts rather than standard-length units. Compatibility covers touring car short dampers in Items 50519, 50746, 53155, 53280, 53571, 53901, 54000, 54753, 42102, 42273, 42287, 42291 and 47342. On a practice day or between race heats, swapping one pair for another gives a clear mechanical route to adjusting handling balance through the suspension rather than changing the whole chassis setup. Warning! Not suitable for children under 14 years.
RC tuning parts
33T Steel Idler Gear, chassis spare part
300022087€9.49
This 33T steel idler gear is a dedicated spare part for selected RC chassis and brings a precise transmission component into repair and maintenance work. Supplied as 1 piece, it is intended for use with the BB-01, TD2, TD4 and XV-01 chassis, where the stated 33-tooth specification matches the required internal gear position. The part is used in place of MA27, identified in the source data as the green gear in the reference image. That direct replacement note matters during servicing, because it points to the exact gear position rather than leaving fitment to guesswork. The steel construction suits a mechanical role inside the drivetrain, while the compact gear form with central hub and slot reflects its function as a transmission component rather than an external accessory. For chassis owners keeping a running model in service, a clearly specified spare like this helps restore the intended internal setup with the named tooth count and platform compatibility. It fits naturally into workshop tasks such as replacing a worn transmission gear during a rebuild, refreshing a used chassis, or keeping a matching spare on hand for BB-01, TD2, TD4 or XV-01 maintenance. The single-piece format keeps the scope clear when one exact idler gear is needed. Warning! Not suitable for children under 14 years.
RC tuning parts
3x23mm Turnbuckle Shaft, RC spare part, blue
300054248€8.79
These 3x23 mm turnbuckle shafts are built for RC chassis tuning where precise linkage adjustment matters. The central turnbuckle section changes shaft length without removing the adjusters, which helps keep setup work direct when steering or suspension geometry needs a measured correction. The blue anodized finish gives the aluminum parts a clean technical look that stands out clearly in a parts tray or on the workbench. The set contains 2 threaded rods and is intended for a wide range of compatible chassis: M-06, M-06 PRO, TA06 MS, TA06, TA06 PRO, TA05, TB-Evo.7, TB-05 PRO, TT-02 TYPE-SR, TT-02 TYPE-S, XV-02PRO, XV-01, XV-01 PRO and XV-01T. Aluminum construction keeps the parts light while providing the rigid threaded form needed for repeatable adjustment. The 3x23 mm size makes this pair a specific fitment choice rather than a generic linkage part, which is useful when maintaining an existing build or preparing a chassis for a setup change. On a bench build, these shafts suit routine replacement, geometry correction or tuning updates between running sessions. The visible center section supports tool access for small length changes, making them practical spares for regular chassis maintenance.
RC tuning parts
4x18mm Titanium Turnbuckle Shafts, RC chassis part
300022086€11.99
These 4x18mm titanium turnbuckle shafts are a dedicated chassis option part for the TA08R family and related Tamiya platforms. The titanium construction pairs low weight with a crisp machined finish, while the threaded design allows the shafts to serve as key linkage hardware in compatible RC chassis assemblies. The set contains 2 shafts and is specified for use with the TA08 PRO, TA08R and TB Evo.8 chassis. Each shaft uses a double-threaded layout with a narrow centre section, a format commonly used where steering or suspension links need compact, accurately made connection points. As an option part, this pack suits routine maintenance, targeted replacement of worn hardware, or a planned chassis refresh using the exact stated size of 4x18mm. For a complete kit application, 4 shafts are required. In workshop use, the clearly defined compatibility helps when matching parts to an existing TA08 PRO, TA08R or TB Evo.8 build. The 2-piece pack also supports staged servicing, whether replacing individual linkage points or combining multiple packs to equip a full chassis with the required shaft count. Warning! Not suitable for children under 14 years.
RC tuning parts
5mm Alum. Ball Nut, RC spare part, blue, 10 pcs
300053640€14.29
This spare parts set supplies 10 aluminium ball nuts in a 5 mm format for RC model maintenance, with a blue anodized finish that gives compatible assemblies a clean, uniform look. Each piece combines a rounded ball head with a hexagonal base, a shape that supports attachment to matching sockets and linked mechanical parts where smooth, accurate movement matters. The set is intended for replacing worn ball connector nuts before play in the linkage becomes imprecise. Fresh hardware helps compatible steering and suspension connections seat correctly and move with less unwanted slack, which supports consistent running performance during regular use. The included quantity of 10 pieces suits full maintenance sessions, partial rebuilds or keeping matching replacements ready in a workshop parts box. Scope of delivery: 10 ball nuts. These aluminium ball nuts fit naturally into routine service work on RC models that use this connector style, whether a single linkage needs attention or several mounting points are being refreshed together. They cannot be used on DT-02 chassis XB models. Warning! Not suitable for children under 14 years.
RC tuning parts
5mm L.Friction Adjuster, RC spare part, 8 pieces
300053601€6.79
The 5 mm L.Friction Adjuster set brings a focused upgrade to linkage movement on compatible RC models. Made from a low-friction material, these ball connectors help linkage rods move smoothly at the connection point, which suits steering tie-rods and camber links that rely on clean, consistent articulation. Each pack contains 8 adjusters and is intended for many Tamiya vehicles that use a 3 mm turnbuckle. The 5 mm connector size makes this set a practical choice when worn rod ends need replacement across several mounting points in the same setup. The parts are supplied as adjustment pieces for model maintenance and tuning, with the connector shape built around ball-joint style linkage use. Compared with the standard material, this low-friction version lasts longer before replacement is needed. The set fits naturally into workshop tasks such as refreshing steering linkages, rebuilding camber link connections, or keeping spare rod-end parts ready between running sessions. DT-02 chassis compatibility is stated, while XB model use is not possible. Warning! Not suitable for children under 14 years.
RC tuning parts
5mm Suspension Balls, RC spare parts, low friction
300054747€9.29
These 5mm suspension balls bring a focused drivetrain and chassis tuning detail to compatible RC vehicles by reducing friction where the suspension pivots. Made from POM resin and supplied as a set of 8, they suit Tamiya vehicles that utilize 5mm suspension balls and give a straightforward way to refresh worn hardware or standardize a setup across multiple corners of the chassis. The design was originally used on the TRF419X chassis, which places these parts in proven competition-oriented running gear rather than generic workshop stock. At each mounting point, the low-friction surface helps the suspension move with less resistance as arms and linkages cycle through travel. That smoother motion can help the suspension react more cleanly to steering input, surface changes and load transfer, especially when a setup depends on free, consistent movement at small contact points. In workshop use, this set fits naturally into routine rebuilds, race preparation and parts replacement on compatible models. The 5mm size keeps selection simple for chassis built around that specification, while the pack of 8 provides enough pieces for a complete refresh of key suspension connection points on many layouts.
RC tuning parts
630 Ball Bearings, chassis tuning parts, set of 8
300054925€15.49
This set of 630 ball bearings adds a direct mechanical upgrade to compatible chassis by replacing plain rotating contact points in the reduction gears with metal bearings designed for smoother running. With 8 bearings in the pack, the set suits targeted maintenance work or the first stage of a driveline tune-up on G6-01TR and GF-01TR models. The main effect comes from lower friction at moving points inside the reduction gear assemblies. That reduction in drag helps the drivetrain transfer motion more efficiently and can lessen wear on surrounding rotating parts over time. The bearings have a compact round format with a polished metal finish, matching the small-scale hardware used in RC chassis assemblies. Each reduction gear requires 2 of these 630 bearings, so quantity planning is straightforward when preparing a larger rebuild. A full GF-01 setup needs 16 bearings in total, while a full G6-01 setup needs 24. In workshop use, the set fits neatly into routine servicing, parts replacement, or a gradual chassis upgrade path. It can be used to refresh a model that has seen regular running or to prepare compatible reduction gears before the next driving session.
RC tuning parts
Alu Wheel Hub Clamp Type 9mm, RC car hub set
300054610€16.79
This clamp type wheel hub set adds a precise 9 mm setup option for compatible RC cars that use hex hubs to secure the wheel on the axle. Each aluminum hub clamps directly onto the wheel axle, a fastening method that increases holding strength while supporting smoother wheel rotation during running and tuning work. The set contains 2 wheel hubs, a 1.5 mm hex wrench, cap screws and 2 x 10 mm shafts for attachment. The machined aluminum parts keep weight low while giving the hub area a crisp, technical fit. At 9 mm thickness, this version expands the range beyond 4 mm, 5 mm and 6 mm hub options, which makes it useful when adjusting track width and wheel position on suitable chassis. The instruction data also notes that fit depends on wheel width and offset, and wheels may contact the bodyshell on some combinations. Compatibility covers TT-01 and TT-02 chassis with longer wheel axles and wide rear tread, plus GF-01 and WR-02G chassis cars. In a workshop setup, the clamp design, included hardware and exact 9 mm thickness make this set a practical choice for replacing wide type wheel hubs or refining the stance of an existing RC car build.
RC tuning parts
Alu. Motor Guard GF-01/WR-02, RC motor cover
300054817€38.99
The Alu. Motor Guard GF-01/WR-02 adds a compact aluminum shield around the motor area on compatible Tamiya chassis, combining physical protection with airflow-focused shaping. Slotted openings across the guard help dissipate heat while the cover reduces direct exposure to dust and debris during running. The set contains 1 aluminum motor guard, 2 cap screws in 3x28 mm size and a hex wrench for attachment. Its cylindrical clamp-style form wraps closely around the motor, while the front flange uses multiple mounting holes to secure the part in position. The aluminum construction gives this accessory a precise machined look that suits detailed RC builds and upgrade-focused maintenance. Compatibility is stated for GF-01, G6-01 and WR-02 chassis cars, making it a targeted fit for those platforms rather than a universal add-on. On dirt sections, mixed surfaces or general outdoor running, the guard adds a useful barrier where loose debris can gather around the motor can. It also suits workshop refreshes and chassis upgrades where a cleaner motor area and a more finished mechanical layout are part of the goal.
RC tuning parts
Alum. Adjustable SepSusMt (A), RC chassis mount
300054884€25.99
Alum. Adjustable SepSusMt (A) brings bushing-based suspension tuning to compatible RC chassis cars with a compact aluminum mount set that replaces the standard suspension mount. The two separate mounts, A-a and A-b, work with offset bushings to alter suspension shaft position, opening detailed setup changes that can be felt in how the chassis is balanced for different track conditions. The set contains 1 Aluminum Adjustable Suspension Mount (A-a), 1 Aluminum Adjustable Suspension Mount (A-b) and 1 bushing sprue. The bushing sprue provides 7 pairs of bushing types, and each type uses a different hole position for the suspension shafts. Rotating and pairing those bushings creates 25 potential shaft offset positions, which allows fine adjustment of toe angle, tread, roll center and skid angle. The mount itself allows settings between XA and C, while the final toe angle depends on the separate suspension mounts and bushings used. Shims can be used to adjust clearance where needed. The blue anodized finish gives the aluminum parts the familiar Tamiya look on the chassis. Compatibility is stated for TRF419, TA07 and TB-05 chassis cars, making this set a focused upgrade for racers refining suspension geometry with measured, repeatable changes.
RC tuning parts
Alum. Ball Connector blue 5mm, RC spare part
300053642€13.79
These 5 mm aluminum ball connectors are a focused upgrade and replacement part for the DT-02 chassis, combining low weight, durable metal construction and a blue anodized finish in a compact hardware set. Each connector uses a threaded shaft, a hexagonal base section and a spherical head, creating a secure mounting point that still allows the linked component to articulate smoothly during running. The set contains 10 ball heads, making it useful for servicing several connection points in one session or keeping matching spares ready for later maintenance. The anodized blue finish gives the hardware a crisp technical look while also making the parts easy to distinguish during a rebuild. Replacing worn connectors in time helps maintain clean linkage action where play or wear can reduce consistency. These parts are not available for XB model use. On a workbench, the connectors suit routine chassis upkeep, targeted repairs and detail-focused tuning on a compatible DT-02 build. Once fitted, the smooth ball shape supports free movement at the joint, which matters wherever linked parts need to pivot through repeated steering or suspension travel. Warning! Not suitable for children under 14 years.
RC tuning parts
Alum. HT Servo Saver Cap, RC spare part, aluminum
300054863€5.59
The Alum. HT Servo Saver Cap is a compact RC spare part that combines a machined aluminum build with a precise fit for hi-torque servo savers. Used in place of the Q4 part, it creates a durable contact point at the saver and brings a crisp blue anodized finish to the steering area, where small hardware details remain visible during maintenance and setup. Its disc-shaped form with a countersunk center is made to seat the fixing screw neatly while keeping the cap aligned in the assembly. The aluminum construction adds a lightweight metal component to a high-load area, and the laser-engraved TAMIYA name gives the surface a clean workshop look without changing the part's function. Supplied as 1 cap, it is suited to replacing a worn original part or refreshing a compatible saver with the same specified shape and role. On an RC chassis, this cap fits naturally into routine steering service, rebuild work or detail-focused tuning. It is especially useful when a hi-torque servo saver is already apart for inspection and the Q4 position needs a fresh, more durable replacement component.
RC tuning parts
Alum. Turnbuckle Shaft 3x18mm, RC spare part
300054247€8.79
The Alum. Turnbuckle Shaft 3x18mm in blue is a compact RC spare part for chassis setups that call for precise linkage adjustment. Made from lightweight aluminum, each shaft combines threaded ends with a central section that supports clean, controlled length changes while the part remains installed, which helps keep setup work focused and efficient at the bench. The 3 x 18 mm format suits a wide range of compatible Tamiya chassis, including M-08 CONCEPT, M-06, M-06 PRO, MF-01X, TA08 PRO, TA07 MSX, TA07 MS, TA07 PRO, TB-Evo.6 MS, TB-Evo.6, TRF420X, TRF420, TRF419XR, TRF419X, TRF419 and TT-01D TYPE-E. A blue anodized finish gives the aluminum surface a crisp technical look and makes the parts easy to spot during maintenance. The stopper uses a slot that is tightened with a cap screw to lock the shaft securely. This layout also supports subtle position adjustment when a carbon shaft is used, while avoiding shaft damage and reducing the need to install or remove bearings during service. With 2 threaded rods in the set, the pair fits neatly into regular repair, replacement and tuning work on compatible RC chassis. Setup sessions, trackside checks and workshop maintenance all benefit from hardware that can be adjusted directly and returned to the car with minimal interruption. Warning! Not suitable for children under 14 years.
RC tuning parts
Alum. Turnbuckle Shaft 3x42mm, chassis part
300054250€9.39
These 3 x 42 mm aluminum turnbuckle shafts add a clean, mechanical adjustment point to compatible RC chassis, with a blue anodized finish that stands out clearly during bench work and maintenance. The threaded ends and central wrench section support direct length changes on the installed linkage, so setup corrections can be made without removing the adjusters first. The pair is intended for chassis including TA07 PRO, TA06, TA06 PRO, TA06 MS, TB-04, TB-04 PRO, FF-04 EVO, TRF419, TRF419X, TB Evo.6, TB Evo.6 MS, XV-01 PRO and XV-01T. Aluminum construction keeps the parts light while providing a precise metal interface for linkage duties. The turnbuckle format is especially useful where camber, toe or related linkage geometry needs measured adjustment through small rotational changes at the shaft body rather than full disassembly. With 2 threaded rods in the set, the parts suit paired replacement on one linkage point or a focused tuning update on an existing chassis build. The metallic blue surface also makes the shafts easy to identify among other hardware during servicing, rebuilds and trackside setup checks. Warning! Not suitable for children under 14 years.
RC tuning parts
Aluminum Adjustable Servo Horn for RC Steering
300054893€43.99
This aluminum adjustable servo horn adds fine steering setup control to compatible RC chassis by allowing the distance between the servo horn center and ball connector to be set in 1 mm increments from 15 to 22 mm. That mechanical adjustment changes the linkage geometry directly, making it possible to tune steering throw with a part that sits at the heart of the steering system. The horn also allows steering range adjustment, which helps match the setup to different chassis layouts in the compatible CC-01, GF-01, G6-01, M-05, M-06, M-07 Concept, M-08 Concept, TA07 PRO, TB-05 PRO, TT-02 and TT-02B families. Its aluminum construction brings a precise, machined feel to a component that handles repeated steering inputs. A built-in servo saver function adds impact management at the horn itself, so shocks from crashes are not transferred straight into the servo mechanism. On a touring, rally or off-road chassis, this part supports careful steering tuning through measurable linkage changes rather than guesswork. It suits rebuilds, maintenance work and setup changes where steering response and protection both matter in the same installation.
RC tuning parts
Aluminum Servo Horn, RC steering arm for TAMIYA/FUTABA
300042248€15.99
This aluminum servo horn brings a direct steering link to compatible RC chassis and replaces servo saver action with a firmer connection at the servo output. The result is a sharper steering response that suits precise setup work on track-focused models, while the blue alumite finish and machined cut surfaces give the part a clean technical look. The arm uses a raised pillow ball mounting point set 1.5 mm higher to reduce linkage interference and maintain steering angle through the linkage movement. A clamp-style serration section adds extra holding force at the spline, and tightening the 2 x 5 mm cap screw secures the horn more firmly than a screw-only layout. Scope of delivery: 1x servo arm. The part is specified for TAMIYA/FUTABA fitment and is listed for TA07 MSX, TA07 MS, TA06 MS, TB-Evo.7, TB-Evo.6 MS, TB-Evo.6, TRF420X, TRF420, TRF419XR, TRF419X and TRF419. On a competition chassis, small steering changes are easy to feel, and this direct horn is built for that kind of exact linkage setup. It suits rebuilds, tuning changes and replacement work where secure spline clamping and clean pillow ball positioning matter to the steering system. Warning! Not suitable for children under 14 years.
RC tuning parts
Aluminum Turnbuckle Shaft Set, RC Chassis Spare
300054249€8.79
This spare part set brings adjustable linkage tuning to a wide range of RC chassis with 2 aluminum turnbuckle shafts in a blue anodized finish. Each shaft uses a central hex section that allows length changes while the adjusters stay in place, making setup work on steering or suspension linkages more direct and controlled. The shafts measure 3 x 42 mm and are intended to replace the standard A12 parts in compatible kits. Supported chassis listed in the data include TT-02 Type-S, TA07 PRO, TA06, TA06 PRO, TA06 MS, TB-04, TB-04 PRO, FF-04 EVO, TRF419, TRF419X, TB Evo.7, TB Evo.6, TB Evo.6 MS, MF-01X and RM-01. For TC-01 chassis, use with adjusters such as 54869 is specified. The aluminum construction adds a metal component where repeated setup changes call for a precise threaded part with a clear wrenching point at the center. On a bench build, these shafts suit geometry changes that need repeated fine adjustment between runs. In maintenance or upgrade work, the 2-piece set provides direct replacement parts for worn or standard kit linkages on the named chassis families. Warning! Not suitable for children under 14 years.
RC tuning parts
Ball Bearing Set 1150, RC car accessory, 16 pcs
300054579€30.99
The Ball Bearing Set 1150 brings a focused drivetrain upgrade to compatible R/C car chassis by replacing plastic bushings with 16 metal bearings sized at 11 x 5 x 4 mm. Each bearing supports smoother rotation at key moving points, helping the transmission run with less drag during acceleration and steady laps. This set is intended for a straightforward tuning change that targets friction where axles and drivetrain parts turn under load. In compatible entry level platforms, the swap can help reduce power loss through the driveline while also supporting the longevity of axle joints. The pack provides enough bearings for several listed chassis layouts: DT-03 and DT-02 require 14 bearings, while WR-02, WR-02G and WT-01 require 16. That fitment detail makes the set useful both for a complete replacement on some chassis and for a near-complete conversion on others. On the bench, the compact 1150 format suits builders refining a buggy or wheelie platform with a practical mechanical upgrade rather than a cosmetic change. It fits naturally into maintenance work, rebuilds and fresh kit preparation where smoother rolling parts and more efficient drivetrain movement matter most.
RC tuning parts
BB-01 Alum. Servo Stays, chassis accessory
300022070€23.99
These BB-01 Alum. Servo Stays bring a metal mounting upgrade to the BB-01 chassis with 2 silver-anodized aluminium parts shaped for the servo stay position. The machined L-form, stepped inner corner and mixed drilled and threaded holes give each stay a defined structural role inside the chassis layout. The set contains 2 stays, allowing the left and right mounting points to match in material and finish. The silver anodized surface gives the aluminium a clean technical look, while the threaded holes support direct fastening at the intended fixing points. The larger plain holes and the vertical leg geometry indicate a part designed to hold position accurately once installed. As a chassis accessory rather than a general hardware piece, this set is focused on the BB-01 platform named in the data. That makes the pair a useful choice when refreshing a used chassis, replacing the standard servo stays, or adding a more detailed metal element during a new BB-01 build. On the bench, the 2 matching parts bring a neat, uniform appearance to the servo mounting area and keep the upgrade closely tied to the specified chassis system.
RC tuning parts
BB-01 Aluminium Damper Stays Rear Accessory
300022089€26.99
The BB-01 Aluminium Damper Stays Rear accessory adds a metal mounting set to the rear section of a BB-01 chassis build. Its layout is intended for installation under the roll cage roof, where the rear aluminum damper mount bar works with the included adapters and stiffener post to create the specified attachment point. The silver-anodized finish gives the visible parts a clean technical look that matches detailed off-road model assemblies. Included in the set are 1 rear aluminum damper mount bar, 1 stiffener post, 2 damper mount adapters and 2 3x30 mm hex head screws. The two adapters use a double-hole form, while the long central bar and the post create a compact hardware group for the rear damper mounting area. This makes the set useful for BB-01 owners looking for the exact parts named for this chassis rather than a generic hardware mix. In a workshop setup, the parts suit maintenance, replacement or a focused chassis update where the rear mounting section needs the specified metal components. The compact contents also make the set easy to keep with other BB-01 spares for later fitting or rebuild work. Warning! Not suitable for children under 14 years.
RC tuning parts
BB-01 Aluminium Steering Arms L/R, chassis upgrade
300022090€28.99
The BB-01 Aluminium Steering Arms L/R bring a focused steering upgrade to the BB-01 chassis with silver-anodized aluminum parts shaped for the left and right sides. Replacing the standard S2 and S3 parts, these arms add rigidity at a key point in the steering linkage, helping inputs travel through the assembly with a more linear response. Each set contains 1 left arm and 1 right arm, so the steering assembly can be updated as a matched pair rather than mixing materials across the same mechanism. The arm shape uses a larger recessed mounting end and a smaller drilled connection point, with reinforced contours around the structure to support accurate pivoting movement inside the front steering layout. This makes the set especially relevant for builders refining steering feel on a BB-01 based machine rather than changing unrelated chassis areas. The parts are intended for use in place of the original S2 and S3 components on compatible builds. Use with Item 22091 is recommended. Ball bearings are required separately. On the bench, this upgrade suits rebuilds, maintenance work, or a fresh BB-01 assembly where the steering system is being specified with metal linkage parts from the start. Warning! Not suitable for children under 14 years.
RC tuning parts
BB-01 Aluminum Damper Stays Front RC Hop-Up
300022088€44.99
These BB-01 Aluminum Damper Stays Front parts add a focused chassis upgrade to the front damper mounting area. The set uses 2 silver-anodized aluminum stays in place of the standard A27 parts, bringing a metal component to a section that handles the damper attachment points on the BB-01 layout. Alongside the 2 stays, the set provides 2 P3 O-rings, 2 P4 O-rings, 4 countersunk 3x12 mm hex head screws, 2 standard 3x12 mm hex head screws, 2 5 mm ball posts and 4 aluminum spacers measuring 3.1 x 4.4 x 1.0 mm. The countersunk holes in the stays work with the included flush screws for a neat fit. The paired O-rings and spacers support the specified mounting arrangement, while the ball posts add the required connection points for the front setup. This accessory suits builders refining a BB-01 buggy with dedicated chassis parts rather than universal hardware. During assembly or maintenance, the silver finish stands out clearly against surrounding components, making the upgraded front section easy to identify on the bench and on the completed model. Warning! Not suitable for children under 14 years.
RC tuning parts
BB-01 Aluminum Front Uprights, chassis parts
300022069€53.49
These silver-anodized aluminum front uprights are made for the BB-01 chassis and supply a matched 2-piece set for the front suspension area. The identical right and left shape keeps both sides visually consistent and streamlines parts selection when the chassis is being serviced or updated. Each upright features a large central opening for the hub area plus smaller mounting points for the surrounding front-end hardware. That layout supports accurate positioning within the chassis assembly and gives the front corner a clean, precisely machined metal component in place of the standard part. The silver anodized finish adds a crisp technical look that stands out clearly during a build or maintenance session. As a dedicated BB-01 chassis part, this set suits replacement after wear, a rebuild of the front end, or a selective aluminum conversion focused on the upright area. The 2 included pieces cover both front sides, making the pair a straightforward choice when matching geometry and finish across the chassis matters.
RC tuning parts
BB-01 Aluminum Steering Bridge, chassis part
300022091€14.79
The BB-01 Aluminum Steering Bridge is a dedicated chassis part for the BB-01 platform, built to replace the standard S1 part with a silver-anodized aluminum component. Its rigid construction strengthens the steering linkage area, supporting a more direct steering feel and a more even response as the front end changes direction. The part comes as 1 piece and is shaped for the BB-01 chassis layout, so it serves as a focused hardware upgrade rather than a general universal fitting. The silver-anodized finish gives the machined aluminum surface a clean technical look while matching the functional role of a precision steering component. The bridge uses the existing mounting position in place of the S1 part, concentrating the upgrade on the connection point that guides steering movement. Use with Item 22090 is recommended. Ball bearings are sold separately. In a workshop build or a running chassis refresh, this steering bridge suits BB-01 owners who want to refine the front steering assembly with a specific metal replacement part. It also fits well into a step-by-step tuning plan where individual steering components are upgraded one area at a time. Warning! Not suitable for children under 14 years.
RC tuning parts
BB-01 Slipper Clutch Set, chassis spare part
300022071€57.49
The BB-01 Slipper Clutch Set adds an adjustable drivetrain element to the BB-01 chassis, centering on a gear-integrated shaft with 20T layout and a spring-loaded clutch assembly. By changing spring tension, the clutch alters slip timing and acceleration traction, which can help the chassis deliver steadier power when grip changes across the surface. The set contains the slipper clutch for BB-01 Chassis and is supplied with the core assembly parts: 1 gear-integrated shaft, 1 slipper screw, Plate A, Plate B, 2 slipper pads, 1 1050 ball bearing, 2 spring seats, 1 spring and 1 2.6 mm lock nut. The friction-based clutch action lets the drivetrain absorb part of the initial load under acceleration instead of locking the drive instantly, giving more scope to tune how the BB-01 responds as power comes in. The included spare part 86T gear extends service support for the same chassis platform. This set suits rebuilds, routine maintenance and setup changes on BB-01 running cars. It can be fitted when refreshing worn drivetrain parts or when a different clutch response is needed for changing track grip, repeated acceleration runs or general chassis tuning.
RC tuning parts
C.V.A.II Damper Collar, RC spare part set
300050950€7.69
The C.V.A.II Damper Collar set is a dedicated RC spare part for suspension maintenance on selected Tamiya platforms. Supplied as 1 sprue with 22 parts, it concentrates on the damper area and gives compatible chassis a defined source for replacement and setup work. Fitment is stated for DT-02 chassis, DT-03 chassis and DT-03T chassis, with additional use on vehicles equipped with 54567. For DN-01 chassis, the data also names an important restriction: 54028 cannot be used together. That combination note matters during parts planning because it keeps the suspension configuration aligned with the listed specification rather than trial fitting unrelated pieces. The set is not available for XB models, which separates it clearly from those versions. On the bench, this spare part set suits routine damper service, rebuilds after wear, or preparation of a compatible chassis before the next run. The 22-part sprue format keeps the included pieces together in one pack, making it easier to sort the required parts for maintenance on the supported DT and DN platforms. Warning! Not suitable for children under 14 years.
RC tuning parts
Carbon Short Damper Stay Set, RC chassis upgrade
300022076€48.99
This Carbon Short Damper Stay Set brings front and rear carbon fiber damper stays into one focused chassis upgrade for XV-02 and XV-02RS cars. The woven carbon fiber plates use multiple mounting holes and slotted positions to open up suspension setup changes, so shock geometry can be adjusted with more precision on paved running surfaces. The set contains 2 damper stays, 4 piston rods measuring 30.5 mm, 8 blue 5 x 6.55 mm ball connector nuts, and 8 round head socket screws in 3 x 10 mm size. The front and rear plates have distinct shapes for their mounting positions, with rounded outer edges, central slots and lower slotted openings that support different attachment points. That layout helps tune how the dampers sit on the chassis and how the suspension reacts through direction changes and corner entry. The supplied piston rods are specifically oriented for on-road performance rather than a general mixed-surface setup. On an XV-02 chassis, this set is used with Items 42102, 54465 and 54871; it also fits XV-02RS chassis cars. It suits builders refining a rally platform for asphalt sessions, club practice or repeatable setup testing where small geometry changes can be felt from one run to the next.
RC tuning parts
CC-01 Alum. Oil Damper Set, RC chassis upgrade
300054541€66.99
The CC-01 Alum. Oil Damper Set is an RC chassis upgrade made for the Tamiya CC-01 platform, using aluminum dampers to bring more composed suspension movement to cross-country running. On loose gravel, rutted tracks and uneven ground, the oil-filled design helps the chassis absorb repeated bumps with a steadier response than a basic friction setup. The set provides the parts needed to assemble 4 dampers, covering both front and rear positions for a balanced suspension layout. Each damper uses a silver anodized cylinder with a dark titanium anodized cap, giving the hardware a clean mechanical look that matches detailed off-road builds. V parts are included, along with small attachment parts for mounting to the chassis. The assembly sheet for the damper set notes standard oil as #400 and indicates separate front and rear spring use from the base kit. This upgrade suits builders refining a CC-01 for trail driving, rocky paths or mixed-surface sessions where repeated compression and rebound shape how the chassis settles after bumps. It also fits restoration or tuning work on an existing CC-01, where metal dampers can replace worn stock units with a full 4-piece suspension set. Warning! Not suitable for children under 14 years.
RC tuning parts
CC-01 Barrel Spring Set, chassis tuning springs
300054666€20.29
The CC-01 Barrel Spring Set adds a focused suspension tuning option to compatible CC-01 chassis cars, using 6 coil springs in 3 stiffness grades to change how the chassis reacts over rough ground. Its barrel shape creates progressive damping, which means resistance increases the further each spring is compressed, giving the suspension a more measured response when the surface starts to break up. The set contains 2 soft springs, 2 medium springs and 2 hard springs, making it possible to fit matched pairs and compare different setups with the same chassis. The springs are shown with colour bands that identify hardness at a glance, helping setup changes stay organised when several rates are on the bench. The shorter and longer spring forms in the set broaden the tuning range within the CC-01 platform and keep the adjustment centred on suspension behaviour rather than cosmetic changes. On loose tracks, gravel paths or uneven off-road sections, the progressive spring action supports a smoother ride and helps the chassis manage body roll with more control. For maintenance, replacement or planned tuning sessions, this spring set gives CC-01 owners a direct way to refine handling through a core suspension component.
RC tuning parts
CC-02 Damper Spring Set, RC chassis suspension parts
300054992€18.29
Built for CC-02 chassis cars, this damper set upgrades the suspension with 4 aluminum cylinders shaped for lower friction and a slimmer profile than the kit-standard cylinders. That narrower cylinder form changes the visual balance around the axles and gives the chassis a more scale-focused look while the dampers work through bumps, ruts and side-to-side weight transfer. Each damper uses cylinder caps, O-ring caps and adjustable retainers, with small attachment parts included to complete the installation. The top and bottom mounting points use ball connectors, replacing the kit's upper screw and collar arrangement. That mounting change supports smoother roll motion, especially when the chassis articulates over uneven ground or settles into off-camber sections. The set is intended to kit out a full 4-damper layout on the CC-02 platform rather than changing only one corner of the suspension. Compatibility stays flexible for tuning work, because the dampers can be paired with kit-standard springs or with the dedicated springs sold separately as Item 54992. This makes the set a useful choice for builders refining suspension response, scale appearance and chassis movement on trail-style RC vehicle builds.
RC tuning parts
CC-02 Full Ball Bearing Set, chassis tuning set
300054910€35.99
The CC-02 Full Ball Bearing Set is a focused chassis tuning upgrade for compatible CC-02 models, built around 22 metal bearings in 4 specified sizes. Installed in the rotating points of the chassis, the bearings support smoother movement and more efficient transfer of drive power than plain bushings, which helps the model run with less drag during use. The size mix of 2x 850, 16x 1150, 2x 1260 and 2x 1510 is matched to the CC-02 platform, so the set covers a full conversion with the required quantities already grouped in one pack. Ball bearings are often one of the first mechanical upgrades added to an RC chassis because they reduce friction where shafts and driven parts turn under load. That lower friction can also help reduce wear in those contact areas over time, especially on a model that sees regular running and routine servicing. During a rebuild, maintenance session or fresh chassis assembly, this set gives a direct route to replacing bushings with bearings across the specified CC-02 layout. The compact metal parts suit hobby benches where precise fit and orderly parts selection matter, and the pre-matched count keeps the upgrade process straightforward for the intended chassis family. Warning! Not suitable for children under 14 years.
RC tuning parts
CC-02 Motor Mt. Bridge Spacer, chassis accessory
300054971€27.29
The CC-02 Motor Mt. Bridge Spacer adds a focused chassis upgrade to CC-02 builds by reinforcing the motor mounting area with an aluminum part placed between the gearbox and the motor cap screws. That extra support helps keep the motor fixed in position, which contributes to a more efficient drive when the gears are set correctly and turning smoothly. The spacer also braces the gearbox against warping, giving the motor mount area firmer support under load. Its gun metal anodized finish matches the technical character of RC chassis hardware, while the curved bridge shape and elongated slots support accurate placement during fitting. The instruction diagram shows the spacer used with 3 x 14 mm cap screws and 3 mm washers while the motor position is adjusted to create proper gear backlash. This setup allows clearance for the gears to run lightly instead of binding at the mesh point. On a workbench build or a maintenance session, this part suits drivers refining drivetrain feel on a CC-02 chassis car. It can be fitted when replacing motor mount hardware, correcting gear mesh, or adding stiffness to the gearbox area for more consistent running across repeated sessions.
RC tuning parts
Clamp Alu Wheel Hub, accessory set, 5 mm blue
300053823€36.29
Clamp Alu Wheel Hub 4 5 mm blue brings a more secure wheel mounting setup to compatible Tamiya chassis through a split aluminium hub tightened by cap screws. The machined blue hubs sit neatly at the axle area and are designed to hold firmly during running, while the clamp construction also keeps 2 x 10 mm stainless steel shafts from slipping out when the hub is removed. This accessory set is intended for a broad range of chassis platforms, including TT-02, TT-02 Type-S, TT-02D, TT-01D Type-E, TT-01 Type-E, TT-01 Type-ES, TA07 PRO, TA06, TA06 PRO, TA06 MS, TA05 Ver.II, TB-04, TB-04 PRO, FF-04 EVO, FF-03, FF-03 PRO, TRF419, TRF419X, TB Evo.7, TB Evo.6, TB Evo.6 MS, M-07 Concept, XV-01T and XV-01 PRO. Use with item 53646 or 53647 is specified where required. The scope of delivery lists 1 Wheel Driver Set with 15 pieces, and the product image shows 4 blue clamp hubs, metal screws, pins and an L-shaped hex key. On a workshop bench, the cap screw fixing allows each hub to be tightened with a direct mechanical grip rather than a simple push fit. During maintenance, wheel removal and refitting stay controlled because the shaft hardware remains retained in the assembly, which helps keep small drivetrain parts organised between runs. Warning! Not suitable for children under 14 years.
RC tuning parts
Clamp Type Alum Hubs NarTrd (4), wheel hubs
300042352€20.99
Clamp Type Alum Hubs NarTrd (4) brings a focused chassis tuning option to touring car models with 4 narrow tread clamp type wheel hubs in aluminum. Mounted at the wheel area, these hubs allow a narrower tread setup that can be used at the front for sharper steering response, at the rear for improved grip, or across the whole car to tune overall balance on the track. Each hub uses a clamp type design and comes with 5 cap screws in 1.6 x 4 mm size for installation. The aluminum construction is finished in Tamiya blue anodizing, giving the parts a crisp technical look that stands out during maintenance and setup work. Compatibility covers TA06, TA06 PRO, TA06 MS, TA07 PRO, TA07 MS, TB-04, TB-04 PRO, TB-05 PRO, TB Evo.6, TB Evo.6 MS, TB Evo.7, TRF419, TRF419X, TRF419XR, TRF420 and TT-02 Type-S chassis. For use with 24 mm width medium-narrow wheels, and items 53646 and 54573 may be required. This set fits naturally into bench tuning before practice laps, race-day setup changes, or a rebuild focused on steering feel and rear traction. The 4-hub format supports a full car conversion, while the clamp layout keeps the adjustment centered on a small but influential chassis component.
RC tuning parts
CR-01 Reinforced Drive Shaft Diff Lock Set
300054108€46.49
Built for the CR-01 chassis, this reinforced drive shaft and diff lock set changes the axle drivetrain into a more direct, mechanically linked setup. The reinforced long and short drive shafts work with diff lock case A and diff lock case B to lock securely in place, supporting efficient power transfer when the axle is under load. The differential lock parts install in place of the bevel gears, as shown in the assembly layout, so the axle no longer relies on standard differential action. That change keeps both sides of the axle turning together, a setup often chosen for technical crawling lines where steady drive at both wheels matters. The set also uses 4 mm E-rings together with 3 x 6 mm screws and 2 x 5 mm cap screws in the assembly. Scope of delivery: 1 reinforced differential lock set with 14 pieces. As a chassis-specific tuning set, these parts suit CR-01 builds that need drivetrain components matched to the original axle housing layout. The black mechanical parts format also makes the upgrade easy to identify during maintenance, parts replacement or a fresh rebuild of the axle section. Warning! Not suitable for children under 14 years.
RC tuning parts
CR-01 Reinforced Wheel Axle, chassis spare pair
300054048€11.29
The CR-01 Reinforced Wheel Axle is a chassis spare pair made for the CR-01 platform and supplied as 2 matching replacement parts. Each axle uses stronger material than the standard version, giving this small drivetrain component a more durable basis where wheel-end hardware and repeated impacts concentrate force. The dark metal finish and machined form underline its role as a functional running part rather than a cosmetic add-on. Each piece combines a slotted lower section, a smooth central shaft with a cross-hole and a threaded tip, so the axle can take its place within the existing wheel assembly layout. The upgraded cup area brings improved wear resistance, targeting a contact point that sees repeated movement during running. That makes this pair a practical choice when a CR-01 build needs fresh axle hardware after demanding use on steep sections, uneven ground or hard descents. In workshop use, the pair suits routine maintenance, worn-part replacement or a durability-focused refresh of an existing chassis setup. For RC owners keeping a CR-01 ready for regular trail sessions, these 2 axles add a direct fit spare option centered on strength and wear performance. Warning! Not suitable for children under 14 years.
RC tuning parts
Damper Set Alum. M-Chassis (4), RC damper set
300054000€99.99
This aluminum damper set brings a chassis-specific suspension upgrade to M-Chassis builds with 4 oil dampers developed around a shorter format. The damper cylinders and damper rods are 2 mm shorter than touring car aluminum dampers, which lowers ride height and opens up more exact stroke adjustment on compact chassis layouts. The set is supplied as a 118-piece assembly package with threaded cylinders, adjustment nuts, springs, pistons, O-rings and mounting hardware. A hard black coating on the damper surfaces reduces friction, while the blue damper caps and white springs give the assembled suspension a crisp mechanical contrast. The internal setup can be tailored through piston choice, with 2-hole and 3-hole pistons specified for different chassis positions in the included build information. Standard damper oil is #400, and damper oil is available separately. On the bench, the set supports detailed front and rear suspension work for M-03, M-04, M-05 and M-06 chassis. It can also be used with TT-01 TYPE-E and TT-01D TYPE-E chassis together with 54059 and 54060, and with MF-01X chassis when the stated 5 x 9 mm cushion balls are added. The result is a more precisely tunable damper package for drivers refining ride height, spring tension and damping response. Warning! Not suitable for children under 14 years.
RC tuning parts
DB-01/TRF501X Reinforc.Belt, drive belt
300054140€11.99
This reinforced drive belt is a dedicated transmission spare part for the DB01, TRF501X WE and TRF511 chassis, combining a 369 size and 3.7 mm width with a toothed inner profile that transfers motion through the drivetrain. In a running model, that layout supports steady power delivery where the belt tracks around pulleys inside the chassis. The belt is supplied as 1 reinforced drive belt and is described as dust repelling, a detail aimed at keeping the drive path cleaner during operation. Its flexible construction is paired with low drive resistance, so the drivetrain can run with less drag while maintaining the belt's engagement on the teeth. The reinforced belt core is stated as about 1.5 times stronger than previous drive belts, and the reinforcement is also described as helping prevent tooth slip under load. That combination makes it a focused replacement part for restoring transmission performance on the named chassis. Used in maintenance, rebuilds or race-day spares, this belt suits model setups where the original transmission part needs replacement after wear. Kept in a pit box or workshop drawer, it gives the stated chassis platforms a matching spare for routine drivetrain service. Warning! Not suitable for children under 14 years.
RC tuning parts
DB01/TRF511 Gear Differential Unit 37T RC Part
300054329€43.99
The DB01/TRF511 Gear Differential Unit 37T adds a sealed oil-filled differential layout to compatible RC buggy drivetrains, replacing the kit-standard ball differential used on DB-01 and 511/502 chassis. That change opens another tuning route at the center of the transmission, where oil viscosity directly influences how quickly the differential moves under load on loose or changing off-road surfaces. Inside the assembly, a 37T pulley works with 12T and 20T bevel gears, while the sealed case uses a gasket, O-rings, shafts, shims and screws to hold the oil around the internal gear set. The instruction data specifies filling the case until the bevel gears are covered, making the working principle clear and easy to service. Higher viscosity oil slows differential movement, so the same unit can be adjusted for different grip levels and handling balance. Compared with a standard ball differential, this gear differential requires less frequent maintenance cycles. The included cross shaft from Item 54311 is supplied as standard, and the differential joint cups can also be sourced later as spare parts. On a prepared buggy, this unit suits drivers who tune for specific track conditions rather than leaving the stock setup unchanged. It also fits workshop maintenance sessions where a worn drivetrain is being refreshed with a sealed differential format that can be reopened, refilled and adjusted as running conditions change. Warning! Not suitable for children under 14 years.
RC tuning parts
DF-02/TT-01 Front One-way Unit, RC drivetrain set
300053671€84.99
The DF-02/TT-01 Front One-way Unit changes the front drivetrain layout by replacing the front differential gear with a one-way mechanism. Under power, the front end keeps traction engaged; when throttle is off, the difference in rotation between front and rear wheels is canceled, supporting smoother, stall-free cornering on technical sections and tighter turns. The set contains 19 parts and is built around the one-way ring gear, left and right front one-way housings, one-way joints, bearing spacers and 1060 flanged ball bearings. During assembly, the housing and ring gear holes are aligned and secured with 2 x 8 mm cap screws using the included 1.5 mm hex wrench. The instructions also note a 6 mm washer adjustment when a universal shaft shows excess play at the one-way joint, giving a clear mechanical route to fine-tuning fit. Fitment details matter with this upgrade. TT-02 TYPE-S and TT-02 TYPE-SR chassis use it together with 53590, TT-02B requires the 6 mm O-ring MB16 in the connection cup, and TT-02RR uses the kit wheel axle and driveshaft together with 53590. For DF-02 and TT-01 based builds, this unit suits tuning sessions focused on front-end response and drivetrain behavior rather than cosmetic changes alone. Warning! Not suitable for children under 14 years.
RC tuning parts
DF-03 Damper Spring Set, chassis tuning set
300053927€26.99
The DF-03 Damper Spring Set adds a focused suspension tuning option for compatible RC buggy chassis by putting 12 metal coil springs with 3 distinct hardness levels into one pack. Soft black, medium gold and hard silver springs give a clear starting point for adjusting how the dampers react to bumps, grip changes and direction shifts on different surfaces. The 3x4 configuration supplies a full set arrangement, so matching spring rates can be fitted across the vehicle instead of mixing unrelated parts. On loose dirt, a softer rate can help the suspension move more freely over uneven ground, while firmer springs suit higher-grip sections and route layouts that call for a tighter response. The color coding speeds up setup checks between runs because each hardness level is easy to identify at a glance. This set is specified for DF-03, TT-02B, DB02, DB01, DN-01 and TRF201 chassis, and TT-02B use is stated together with 53926. At the bench, the springs give a direct way to test setup changes before the next battery pack goes in. On the track, that means suspension tuning can follow the road surface and course shape more closely, whether the goal is a calmer reaction over rough sections or a firmer feel through faster lines. Warning! Not suitable for children under 14 years.
RC tuning parts
DT-03 Carbon Damper Stay Front RC Chassis Part
300054562€19.49
The DT-03 Carbon Damper Stay Front is a chassis upgrade part for DT-03 cars that brings a stiffer front damper mounting point to the suspension layout. Its carbon plate construction and symmetrical multi-hole pattern give the front end a clean, technical setup for damper installation, with the curved upper edge and twin lower tabs shaped to match the chassis mounting area. This set is supplied as ITEM 54562 and is intended to replace the standard C5 part on the DT-03 platform. The included hardware consists of 2 ball connector nuts, 2 3x8 mm screws and 2 3x0.7 mm spacers, which match the mounting points shown for the stay itself. The drilled positions allow adjustment of damper attachment points, which helps builders alter front suspension geometry through the mounting location rather than through unrelated chassis changes. The part is documented for use in place of C5 and for compatibility with the DT-03 CVA Damper Set. On a buggy prepared for loose dirt, compacted track sections or repeated jump landings, the front stay gives the suspension area a more focused base for setup changes. It suits workshop tuning sessions where front damper position, linkage fit and chassis response are adjusted step by step on a DT-03 build.
RC tuning parts
DT-03 Carbon Damper Stay Rear, chassis upgrade
300054563€22.59
The DT-03 Carbon Damper Stay Rear brings a focused chassis upgrade to DT-03 models by combining carbon fiber construction with a rear suspension mounting layout designed for tuning. The flat carbon plate gives the dampers a rigid mounting point, helping the suspension work with a more direct, controlled feel during running sessions. A series of mounting holes across the stay creates more setup scope than a fixed-position part. Damper angle and mounting position can be adjusted to explore different handling responses, making the part useful for track tuning as well as routine chassis refinement. The set also contains the small attachment parts needed for installation, so the carbon stay can be fitted as a complete rear mounting component rather than as a bare plate alone. The instruction data identifies it as a replacement for the standard stay position on DT-03 chassis models. On a prepared buggy, this kind of upgrade comes into its own when surface grip, corner entry and rear stability need closer adjustment through damper position changes. It also suits workshop builds that focus on replacing standard chassis parts with lighter, more rigid option components matched to the DT-03 platform. Warning! Not suitable for children under 14 years.
RC tuning parts
DT-03 Full Turnbuckle Set, RC chassis upgrade
300054572€22.49
The DT-03 Full Turnbuckle Set adds adjustable linkage hardware to DT-03 chassis cars, replacing fixed upper arms and tie-rods with 6 stainless steel turnbuckle shafts. Threaded adjustment makes it possible to fine-tune link length for a more exact chassis set-up while the buggy sits on the bench between runs. The set includes 2 shafts in 3x32 mm, 2 in 3x38 mm and 2 in 3x65 mm, covering the different positions used around the chassis. Each shaft uses an adjustment section that can be turned with the included wrench, so changes can be made without removing every linkage point first. Stainless steel construction gives the shafts a clean, precise finish suited to repeated set-up work, and the supplied attachment parts support installation on compatible DT-03 models. This upgrade suits drivers who want to refine alignment after a rebuild, correct steering link length, or make measured suspension changes for different running conditions. On a maintenance table, at a club session, or between outdoor buggy runs, the set gives the DT-03 platform a more tunable linkage layout with parts sized for direct compatibility.
RC tuning parts
DT-03 Gear Shaft, RC spare part, 5x45mm pair
300054560€3.49
The DT-03 Gear Shaft lightweight 5x45mm set is a focused drivetrain upgrade for DT-03 chassis cars, replacing the shafts used with the spur gear and counter gear. Its pipe construction cuts weight at a rotating point in the transmission, which supports a lighter, more efficient drive layout during buggy running. Each shaft measures 5x45 mm and the set contains 2 matching pieces for the specified replacement point. The hollow metal form does more than change mass: it also helps dissipate heat, which is especially useful around the drivetrain area where moving parts work continuously. Because the change is concentrated in the gear shaft position, the upgrade targets mechanical efficiency without altering the stated DT-03 fitment. This set suits maintenance, repair, or a planned drivetrain refresh on compatible DT-03 chassis cars. Kept as workshop spares or fitted during a rebuild, the 2 shafts offer a straightforward way to swap out the standard kit parts with a lighter alternative matched to the same application.
RC tuning parts
DT-03/02 19T Steel Pinion Gear, M0.8 Accessory
300054629€5.89
This M0.8 module 19T steel pinion gear is a focused drivetrain upgrade for compatible chassis cars, pairing a compact motor-side gear with a tougher material choice for repeated running sessions. The steel construction is stated as more durable than the kit-standard aluminum pinion gear, helping reduce wear at a part of the transmission that sees constant tooth contact. The gear is supplied as 1 piece and comes with a grub screw for attachment, so the pinion can be fixed directly to the motor shaft in the intended position. The 19-tooth specification keeps the gearing at the stated tooth count, which matters when maintaining an existing transmission setup rather than changing to a different ratio. The M0.8 module matches the stated gear format, giving a clear fit reference alongside the chassis compatibility. Compatible DT-03 and DT-02 chassis cars can use this part as a replacement when the original pinion shows wear or when a steel version is preferred for longer service life. In workshop use, this kind of part suits routine drivetrain upkeep between running sessions, especially when a worn motor pinion starts to affect mesh quality. It also fits neatly into a spares box for chassis-specific maintenance, ready for the next rebuild or transmission refresh.
RC tuning parts
DT-03/02 Ball Diff.-Set, RC drivetrain upgrade
300053863€51.99
The DT-03/02 Ball Diff.-Set is an RC drivetrain upgrade for compatible DT-03 and DT-02 chassis, built to add a ball differential with limited slip effect. That setup improves traction and mobility while keeping the car more settled in fast cornering, so power delivery feels cleaner when the rear end is working across changing grip. Inside the assembly, the gear width is reduced from 20 mm to 15 mm, a change that cuts friction loss in the drivetrain. The set contains 29 parts and includes 2 17 mm thrust washers, 10 steel balls, 1 1150 thrust bearing, 1 diff gear, 1 stepped bolt, pressure plate A, pressure plate B, a pressure plate cap, and long and short gearbox joints. The included grease shown for the ball differential supports the contact surfaces during setup and running. This differential layout also helps protect the gears from damage and wear by managing load through the drivetrain more effectively. Compatibility covers selected DT-03 and DT-02 chassis models such as NEO FIGHTER, RACING FIGHTER, DESERT GATOR, SAND VIPER, NEO FALCON and HOLIDAY BUGGY. For operation, universal joint shafts 300053791 or shaft set 309805551 with 300050823 are required separately. This makes the set a focused choice for tuning an existing buggy with a more adjustable differential action and a drivetrain setup aimed at traction and cornering stability. Warning! Not suitable for children under 14 years.
RC tuning parts
DT-03/02 M0,8 Module 17T Steel Pinion Gear
300054628€5.89
The DT-03/02 M0,8 Module 17T Steel Pinion is a drivetrain upgrade part for compatible chassis cars, built to place a steel gear at the point where motor output transfers into the transmission. Its M0,8 module and 17-tooth layout define the meshing geometry, while the compact pinion format keeps the part focused on clean, direct power delivery inside the gear train. Compared with the kit-standard aluminum pinion gear named in the data, this steel version is intended for greater durability and increased gear life during repeated running. The straight-cut teeth and central bore create the working interface, and the side fixing point uses the included grub screw to fasten the gear onto the shaft. The set contains 1 pinion gear and 1 grub screw, keeping the replacement focused on the essential mounting hardware. The black metal finish and engraved top-face marks give the part a technical, workshop-ready look that matches its mechanical role. In a maintenance setup, this gear suits rebuilds after drivetrain wear or ratio changes that call for a 17T pinion in the specified module. It also fits neatly into a spares box for DT chassis servicing, where a correctly matched steel pinion helps keep compatible RC cars running with the intended gear mesh.
RC tuning parts
DT02&TT01 3x22 LF Sus. Shaft, RC spare parts
300054395€8.19
The DT02&TT01 3x22 LF Sus. Shaft set is a focused RC hardware upgrade for compatible Tamiya chassis, replacing 3 x 22 mm screw pins with shaft parts secured by E-rings. That change gives suspension link points a firm mechanical hold while keeping the assembly compact and precise around moving components. Each shaft has a low-friction coating that supports smoother suspension action as the linked parts cycle through movement. The set includes 4 silver metal shafts with machined grooves and 10 matching E-rings for installation. This configuration suits maintenance work on worn hardware, a planned rebuild, or a fresh chassis assembly where the specified shaft format is required. The grooved ends provide the retention points for the E-rings, so the fastening method is built into the part itself rather than relying on threaded screw-pin installation. Compatibility covers DT-03, DT-03T, DT-02, TT-02RR, TT-02D, TT-02 and WR-02 chassis. In workshop use, the parts support clean replacement of existing suspension hardware and help keep moving assemblies operating with a consistent mechanical feel across repeated runs. Warning! Not suitable for children under 14 years.
RC tuning parts
F-104 HT Saver Alu. Horn, servo horn, blue aluminum
300054159€25.49
The F-104 HT Saver Alu. Horn is a machined aluminum servo horn for the High Torque Servo Saver, created to replace the Q5 section and give the steering system a firmer, more direct feel. Its anodized blue finish makes the part easy to identify during a build or maintenance session, while the metal construction targets stiffness in the steering area rather than changing unrelated chassis parts. This servo horn is specified for the High Torque Servo Saver 300050473 in white and 300051000 in black. The stated fit list also names F104 and the F103 15th Anniversary Chassis Kit Item 84056, plus DT-03 and DT-03T chassis. Further listed applications include TB Evo.7, M-08 CONCEPT, F104VerⅡ, TRF101, DT2 and DT4, showing that the part serves as a focused steering upgrade across multiple supported platforms. The change in material from the standard saver section to machined aluminum is aimed at reducing flex in this specific linkage point. In workshop use, this part suits builders refining steering response on compatible chassis or replacing the original saver horn with a stiffer alternative. It fits naturally into maintenance, rebuild and tuning routines where exact servo saver behavior matters on the bench and on the track. Warning! Not suitable for children under 14 years.
RC tuning parts
F104 Spur Gear Adapter, RC chassis accessory
300054215€3.99
The F104 Spur Gear Adapter is a drivetrain accessory for selected Formula chassis that expands gearing options by allowing touring car spur gears to mount on F103 and F104 platforms. That added compatibility supports finer ratio selection, so a setup can be matched more closely to motor choice and driving area when tuning a model for different running conditions. The adapter is supplied as 1 spur gear adapter and works with a defined group of chassis that includes F104PRO II, F104Ver.II PRO, F104W, F104, F103GT, TRF103, TRF102 and TRF101. Compatible spur gears listed for this part are 50978, 51056, 51215, 53857, 54055 and 54227. The installation layout places the adapter on the shaft before the spur gear, where it acts as the mounting interface for the gear assembly. Depending on the transmission used, the spacer may also allow an increase in the number of differential balls. In workshop use, this part suits rebuilds, ratio changes and chassis-specific drivetrain updates where a broader spur gear selection is needed. It also fits maintenance sessions that replace worn transmission parts while keeping an existing Formula chassis in active running trim. Warning! Not suitable for children under 14 years.
RC tuning parts
F104/F103 Front Upright, RC spare part, reinforced
300054154€8.29
The F104/F103 Front Upright reinforced set is an RC spare part for Formula chassis that replaces the kit-supplied K-6 component with a reinforced design. Supplied as 2 front steering knuckles, the set is intended for front-end service, rebuild work or a targeted upgrade when running a high-output motor or a 0.4 module spur gear. Each upright uses a black molded structure with a ribbed arm section and a mounted metal shaft, creating a compact assembly for the front steering area. The pair format supports matched installation on the left and right side, while the threaded shaft ends and included fastening hardware suit precise chassis work at the bench. Compatibility covers F104PRO II, F104Ver.II PRO, F104W, F104, TRF103 and TRF101 chassis, making this set a useful stock part for several Formula platforms in one pit box. During maintenance between race sessions, worn front-end parts can be swapped as a pair to keep steering hardware consistent across the axle. On a fresh build or chassis refresh, the reinforced construction suits setups that place extra demand on the front assembly, especially when stronger drive output or the stated gear configuration is in use. Warning! Not suitable for children under 14 years.
RC tuning parts
FC 5mm Alum. Ball Nut, RC accessory set
300053599€16.79
These FC 5 mm aluminum ball nuts bring a precise hardware upgrade to compatible RC model chassis, combining a low-friction coating with a lighter aluminum build for smoother moving connections. Supplied as a set of 10, they suit linkage points that rely on clean articulation and consistent mechanical contact during running and setup. Each part uses a rounded ball head with a hexagonal fastening base, a shape that supports controlled installation and a defined connection point for linked components. The metallic finish and machined form match the technical character of model chassis hardware, while the 5 mm specification keeps the fit tied to the stated application. The set is intended for DT-02 chassis use. Cannot be used on DT-02 chassis XB models. This pack fits naturally into maintenance, repair, or tuning work where worn hardware is being replaced or a chassis is being assembled with selected upgrade parts. In workshop use, 10 matching ball nuts provide consistent hardware across several connection points, helping keep steering or suspension movement even across the build. Warning! Not suitable for children under 14 years.
RC tuning parts
Gear Differential Shim Set, model accessory, 0.2/0.3 mm
300054589€7.49
The Gear Differential Shim Set 0,2/0,3mm (4) brings precise spacing control to oil-filled gear differential units used in compatible RC models. With 2 shim thicknesses, 0.2 mm and 0.3 mm, the set allows fine adjustment of the bevel gears so the differential can be set up with closer attention to mesh and internal fit. Each shim measures 5 x 10 mm, making the set suitable for the specified differential format rather than a broad, undefined range of uses. The pack contains 4 shims in 0.2 mm and 4 shims in 0.3 mm, which gives scope for incremental changes during maintenance, rebuilds or tuning work. This is a focused workshop accessory for differential setup, where small measurement changes can matter across the gear train. The set is intended for Tamiya oil-filled gear differential units employed in 4WD touring cars and 4WD off-road buggies. It fits naturally into bench work such as refreshing a differential, correcting gear spacing or preparing a drivetrain for the next running session, with both shim sizes ready in one pack.
RC tuning parts
Lo-Mount Aluminum Retainers, RC damper spring set
300022080€28.49
These Lo-Mount Aluminum Retainers for Large-Diameter Springs adjust spring position lower on compatible RC car dampers, giving the suspension a cleaner working range and a more direct response in handling. The set includes 4 retainers and 4 aluminum spacers sized 5.5 x 0.5 mm, forming a focused tuning upgrade for cars that run large-diameter springs. A thinner section between the damper ends and cylinders allows damper stroke to be used more efficiently, which helps the spring move with less interruption through compression and rebound. Large-diameter springs are often paired with Super Short Big Bore dampers, making this set a useful option when refining suspension geometry around that layout. The slotted retainer shape supports installation around the damper assembly while keeping the update compact and purpose-built. Compatibility depends on the suspension arm shape and damper angle of the chassis in use. On some setups, contact between the dampers and suspension arms can occur, and any interfering area may need to be shaved down. This makes the set best suited to detailed suspension tuning where spring height, stroke use and chassis response are being adjusted with care.
RC tuning parts
M-03/04/05/06 Reinforced Gear Set, chassis spare part
300054277€8.29
The M-03/04/05/06 Reinforced Gear Set black is a drivetrain spare part for selected Tamiya M chassis platforms, built to refresh the gearbox with reinforced transmission components. The black parts set suits repair work, scheduled maintenance and rebuilds where worn internal pieces can affect how cleanly the drivetrain runs. The scope of delivery contains 1 gearbox with 5 parts. Visible component types include spur gears, a splined shaft and circular gearbox pieces that work together inside the transmission housing. As the gears mesh, rotational force is carried through the drivetrain, so the condition of these internal parts matters for smooth mechanical engagement. The reinforced construction is intended as a durable option in the gearbox, as stated in the source data. Compatibility is specified for chassis M-05, M-05 PRO, M-05 Ver.II PRO, M-06 and M-06 PRO. This set fits naturally into workshop tasks such as replacing tired gearbox internals after long running use or preparing a compatible chassis for a fresh rebuild. In a bench setup, the defined platform list helps match the parts to the correct transmission family before installation, keeping service work clear and focused. Warning! Not suitable for children under 14 years.
RC tuning parts
M-05 Low Friction King Pin, chassis hardware
300054237€10.59
The M-05 Low Friction King Pin set brings a focused chassis upgrade to compatible Tamiya platforms by combining stronger metal hardware with a special plated surface that reduces friction loss. In use, that lower-resistance contact supports smoother movement at the relevant suspension or steering mounting point, making this set a practical choice for maintenance, repair, or setup refinement on running models. Each pack contains 4 silver-coloured king pins with a rounded head, a smooth shoulder section and a threaded end. The hex screw head provides a positive drive for tool engagement during fitting, which helps keep attachment controlled when replacing worn hardware. The set is listed for DF-03 chassis, M-06 chassis, M-06 PRO chassis, M-05 ver.II PRO chassis, M-05 chassis, M-05 PRO chassis and MF-01X chassis. The supplied parts are also described as usable with M-05, M-05Ra and TA04 chassis machines. This hardware suits bench servicing, parts replacement and small tuning updates where consistent fastening parts matter across the assembly. Kept in a spares box or fitted during a rebuild, the 4-piece set supports straightforward upkeep of compatible chassis systems. Warning! Not suitable for children under 14 years.
RC tuning parts
M-05 VII Stainless Sus Shaft Set, chassis upgrade
300054613€7.29
The M-05 VII Stainless Sus Shaft Set upgrades the suspension mounting points on M-05 Ver.II PRO chassis cars with 8 stainless steel shafts and matching 2 mm E-rings. Used in place of screw pins, these shafts attach the front and rear arms with a more exact fit, helping the suspension move with greater precision during running and setup work. The set includes 2 newly designed 3x58 mm shafts, 2 shafts in 3x48.5 mm, and 4 shafts in 3x37 mm, covering the different positions shown for the chassis layout. Each shaft has grooves near the ends for E-ring retention, and 16 E-rings are supplied for attachment. The installation guide shows the shafts fitted through the front and rear pivot points, where they are locked in place with the 2 mm E-rings. Long nose pliers are used to attach the retaining rings during assembly. This chassis option suits builders refining an existing M-05 Ver.II PRO setup or replacing the original pin arrangement with stainless steel hardware. On the bench, the different shaft lengths correspond to specific front and rear mounting locations, making the set a focused upgrade for suspension arm attachment rather than a general hardware assortment.
RC tuning parts
M-05 VII Suspension Arm Set, chassis parts
300054606€10.19
The M-05 VII Suspension Arm Set updates the front and rear suspension layout with 1-piece arms developed for the M-05 Ver.II platform. Compared with the standard 2-piece M-Chassis arrangement, the single-piece design increases rigidity at the arm section, which supports a more direct handling feel during setup and running. This set is used on Item 58593 M-05 Ver.II PRO Chassis Kit and also works as a service replacement when original arms are worn or damaged. The front installation uses chassis kit-included parts in place of C3, C4 and C8, while the rear installation replaces C11 and C19. Left and right arm orientation matters during fitting, and the instruction material shows the required mounting positions for front and rear assemblies. For rebound stroke adjustment on M-05 and M-05 PRO chassis, Item 54605 chassis parts are required so the droop screw can be used on the suspension arm itself. Compatibility covers M-05 Ver.II PRO, M-05 and M-06 chassis. M-05 Version 1 and M-06 platforms require parts modification as described on the 54606 instruction sheet. The set suits maintenance, repair and chassis updates where a Version 2 suspension specification is needed.
RC tuning parts
M-05/M-Chassis Freewheel Axle Set (2), RC axle set
300054183€12.29
The M-05/M-Chassis Freewheel Axle Set (2) brings a precise axle upgrade to compatible Tamiya chassis, using machined wheel axles to support a cleaner wheel fit and reduced play at the mounting point. In a workshop setup or during routine chassis maintenance, that added accuracy helps keep the wheel assembly feeling more exact. This set is built around 2 wheel axles and 10 shims, each shim measuring 0.2 mm for fine adjustment work. The shim stack allows small setup changes instead of broad spacing steps, which is useful when dialling in axle fit on M-Chassis platforms. Compatibility covers FF-04 EVO, FF-03, FF-03 PRO, M-08 CONCEPT, M-07 CONCEPT, M-06, M-06 PRO, M-05 ver.II PRO, M-05 and M-05 PRO chassis. The same axle set can also be used for the rear wheels of the M-05 chassis, the rear wheels of the M-03 and the front wheels of the M-04. On a bench, the parts suit rebuilds, replacement work and tuning-focused maintenance where wheel play needs closer control. The compact set fits naturally into a spares box for M-Chassis running gear, ready for targeted axle changes on compatible front-wheel-drive and M platform builds. Warning! Not suitable for children under 14 years.
RC tuning parts
M-07 Concept Alu. Heat Sink RC chassis accessory
300054759€22.79
The M-07 Concept Alu. Heat Sink adds a focused cooling upgrade to the motor area of the M-07 Concept chassis. Its aluminum body uses raised fins to dissipate heat during extended running, helping the motor maintain steadier performance when temperatures build over the course of a long race. The curved shape is designed to mount neatly around the motor position on the chassis, and the blue anodized finish gives the part a crisp technical appearance that stands out during maintenance or setup. A 3 x 8 mm screw is included for attachment, matching the part to its intended mounting point without the need to source separate hardware. The fin structure increases surface area at the motor mount, which supports heat transfer away from the motor can while the chassis is in use. After running, the heat sink may become hot and should be handled with care. This accessory suits M-07 Concept builds that spend longer periods on track, where repeated acceleration and sustained pace can raise motor temperature. It also fits well into maintenance routines that focus on chassis-specific tuning parts rather than broad universal add-ons. Warning! Not suitable for children under 14 years.
RC tuning parts
M-07 Concept Carbon Bumper Support for RC Chassis
300054791€14.49
The M-07 Concept Carbon Bumper Support is a focused chassis upgrade for M-07 Concept cars, replacing the standard B2 part with a carbon fiber version that combines low weight with higher rigidity. Mounted at the front section of the chassis, it is designed to keep the urethane bumper securely in place during running and handling. The support uses a curved plate shape with 2 large mounting holes and a wide semicircular cutout, matching the front layout shown for the M-Chassis platform. The set contains 1 carbon fiber bumper support and the small attachment parts needed for fitting. In the installation diagram, the part is fixed with 3 x 8 mm hexagon countersunk screws and 3 mm countersunk washers in place of B2. The carbon fiber construction gives this component a crisp, woven finish while concentrating stiffness in a part that braces the bumper area. On an M-07 Concept build, this part suits drivers refining the front end with selected option components rather than changing the whole chassis layout. It works as a direct replacement in the intended position, making it a clear upgrade choice for maintenance, tuning, or a fresh rebuild of an existing M-Chassis car.
RC tuning parts
M-07 Concept Carbon D Stay F, RC chassis part
300054761€15.99
The M-07 Concept Carbon D Stay F is a front chassis upgrade that swaps the standard damper stay for a 3 mm carbon fiber part with lower weight and higher rigidity. Mounted at the front suspension area of the M-07 Concept chassis, it changes how the dampers are supported and gives the setup a more direct, more defined feel during running sessions. Its 4 attachment holes expand the tuning range beyond the 2-hole kit-standard shock tower, so damper position can be adjusted with finer steps. That added hole count gives more scope to alter front suspension geometry and handling balance around different track layouts. The set contains 1 front damper stay and attachment screws for installation. The instruction data also identifies this part as a replacement for B11 on the chassis. This upgrade suits M-07 Concept builds that are being tuned around front-end response rather than broad parts changes across the whole car. On indoor circuits, club tracks or home practice layouts, the carbon fiber stay adds a focused adjustment point that can be matched to damper setup and driving conditions. Warning! Not suitable for children under 14 years.
RC tuning parts
M-07 Concept Carbon Damper Stay Rear RC Part
300054762€17.59
The M-07 Concept Carbon Damper Stay Rear brings a sharper suspension mounting setup to the M-07 Concept chassis with a 3 mm carbon fiber plate that combines lower weight with greater rigidity than the kit standard part. Mounted at the rear, it gives the damper area a more precise base for setup changes while keeping the upgrade focused on a key handling point. Its layout expands tuning range with 4 attachment holes, doubling the 2-hole arrangement of the standard shock tower. That wider choice of mounting positions supports more exact damper angle changes when dialing the chassis for different track conditions. The set also includes attachment screws for installation. Instruction data shows use with M-07 L and M-07 M configurations, and the carbon stay is installed in place of part B12. The manual also notes part direction during fitting and specifies 3 x 10 mm screws, 3 x 1 mm spacers and 5 mm ball connector nuts in the assembly layout. On a prepared M-07 Concept build, this rear stay suits tuning sessions where suspension geometry changes are tested one step at a time. It also fits maintenance work that replaces the standard molded part with a carbon fiber alternative at the rear shock mounting area. Warning! Not suitable for children under 14 years.
RC tuning parts
M-07 Concept Rein. C Pts, chassis parts set
300054810€12.19
The M-07 Concept Rein. C Pts set brings a stiffer carbon-fiber reinforced nylon option to the M-07 Concept chassis, giving tuning work a more focused mechanical change than a like-for-like replacement. With 2 C parts sprues in the pack, this set targets the areas where molded chassis components influence flex and load transfer during running. The reinforced material changes the flex characteristics compared with the standard kit parts, which is especially relevant on high-grip carpet and asphalt surfaces where chassis response becomes more immediate. The molded parts show bearing seats, hinge-pin style ends and multiple mounting holes, indicating their role in suspension and steering-related assemblies. 4 small metal washers or spacers are also supplied for assembly where spacing needs to be set correctly. As a chassis-specific option part, the set is made for the M-07 Concept platform and suits maintenance, repair and setup refinement with the correct matching geometry. On an indoor carpet track, the added rigidity can support a sharper, more settled feel through linked corners and direction changes. On asphalt, the same material change gives builders another clear setup route when comparing standard and reinforced chassis parts during tuning sessions.
RC tuning parts
M-07 Concept Rein. D Pts, chassis parts
300054811€12.19
The M-07 Concept Rein. D Pts set upgrades the suspension area of the M-07 Concept chassis with carbon-fiber reinforced nylon parts shaped for a stiffer response than the standard kit components. Supplied as 2 D parts sprues, the set is aimed at running conditions where grip levels place more load into the chassis and suspension. The reinforced material changes the flex characteristic of the suspension arms, helping the chassis react more directly on high-grip carpet and asphalt surfaces. That makes this set a focused tuning choice for drivers refining handling balance rather than changing the basic layout of the car. The arm shape, mounting points and platform-specific fit are made for the M-07 Concept chassis, so the upgrade stays within the intended geometry of the platform. The black molded parts shown in the set provide the core suspension components for this specific replacement and tuning role. On carpet tracks and grippy asphalt layouts, suspension loads build quickly through corners, transitions and repeated direction changes. In that setting, a stiffer arm set can support a more consistent chassis feel lap after lap, whether the goal is maintenance of an existing M-07 Concept or a setup change for higher-traction running.
RC tuning parts
M-07 Concept Stabilizer Set FR, chassis accessory
300054757€33.49
The M-07 Concept Stabilizer Set FR adds a focused suspension tuning option to the M-07 Concept chassis with front and rear stabilizers in 2 stiffness levels each. Soft red and hard blue bars give a clear visual distinction during setup work, while the included adjusters make left and right balance changes easier to manage at the bench or between runs. The set contains 2 front stabilizers and 2 rear stabilizers, covering both ends of the chassis with matching tuning parts. Stabilizer stoppers and small attachment parts are included for installation, so the bar system can be fitted as a dedicated chassis upgrade rather than assembled from separate pieces. By changing stabilizer stiffness, the suspension can be set up with a different level of roll resistance, giving a practical route to refining handling characteristics on the M-07 Concept. This accessory suits drivers who like to tune a chassis for different track conditions and driving styles. It works well as a setup addition for test sessions, club racing preparation, or repeatable comparison runs where front and rear balance changes need to be made with specific hardware rather than guesswork.
RC tuning parts
M-07 Concept Steering Arm Set, RC chassis upgrade
300054763€37.99
The M-07 Concept aluminum steering arm set brings a more exact steering action to the front end by replacing the standard K1 and K2 parts with machined left and right aluminum arms. That change sharpens steering response and gives the chassis a more direct feel through the linkage, while the blue anodized finish adds a crisp technical look to the assembly. The set contains 1 aluminum steering arm left and 1 aluminum steering arm right, plus a screw and adjustment shims shown for installation on the steering mechanism. The leaflet specifies use in place of K1 and K2, with a 3 x 8 mm screw and 3 x 5 x 0.1 mm shims used as spacers during fitting. Those shims help set the arm position on the mounting posts so the steering movement stays free and correctly aligned. Aluminum construction also provides a more secure attachment than the standard FRP parts named in the source data. Installed on an M-07 Concept chassis, this hop-up part suits drivers tuning steering precision for track sessions, setup changes or routine maintenance. Ball bearings are required separately, so the set can be matched with the preferred bearing choice during the upgrade. Warning! Not suitable for children under 14 years.
RC tuning parts
M-07 Concept, suspension mount set, aluminum rear
300054760€34.99
The M-07 Concept aluminum rear suspension mount set brings a precise metal upgrade to the rear suspension area of the chassis. 4 blue anodized aluminum mounts replace the standard D4 parts on both sides, creating a secure attachment point for the suspension arms while adding a clean technical finish to the rear end of the car. Each mount is used with an included suspension ball, and the instruction diagram shows the parts fastening in place with 3 x 16 mm hex flat head screws. That layout matters in use: the suspension ball keeps the joint moving smoothly, including setups where toe is applied to the wheels. The set is focused on one specific chassis area rather than a general hardware assortment, which makes it a targeted option for tuning, maintenance or replacing the original rear mount parts on an M-07 Concept build. On the bench, the 4-piece mount set gives the left and right rear sides matching hardware for a consistent installation. During setup work, the aluminum construction and dedicated fit suit builders who want a defined rear suspension mounting point on the M-07 Concept chassis.
RC tuning parts
M-07C Alu Rear Suspension Mount Set, RC chassis
300054787€34.99
The M-07C aluminum rear suspension mount set adds a focused chassis tuning option to M-07 Concept cars by changing the position of the rear suspension shafts. Each mount uses suspension ball holes offset by 0.5 mm from the standard layout, giving 2 different mounting positions that alter rear suspension arm skid angle at the back of the chassis. The set contains 4 aluminum rear suspension mounts in 2 types, with 2 A parts and 2 B parts, plus the small attachment parts needed for fitting. The mounts replace the standard D4 parts on both sides. Instruction diagrams show 2 example geometry settings, including 1.3° skid angle and 0° skid angle, illustrating how the shaft position changes the rear setup. This adjustment also changes rear roll characteristics, making the set useful when tuning handling for different track conditions. The blue anodized finish gives the machined parts a clear visual distinction during assembly and setup checks. Mounted at the rear of the chassis, these parts suit bench tuning sessions where suspension geometry is adjusted step by step and then checked again after running. For M-07 Concept cars used on changing surfaces, the alternate mount positions create a direct way to refine rear-end response through hardware rather than guesswork.
RC tuning parts
M-08 Alum. Frame Posts, RC chassis accessory
300054966€15.49
The M-08 Alum. Frame Posts set brings a focused chassis upgrade to M-08 Concept cars by replacing the kit-standard B8 components with 4 aluminum posts in a blue anodized finish. Fitted at the section that joins the chassis front and rear, these parts increase overall rigidity and support more responsive handling from the rear-wheel drive layout. Each post is supplied as a matching machined component, giving the conversion a consistent fit across the chassis structure. The change in material from the standard parts to aluminum concentrates on the connection area where stiffness matters, helping the chassis react more directly to steering inputs and load changes. The blue anodized surface also adds the signature Tamiya look to the visible hardware without changing the intended compatibility of the car. This accessory is intended for M-08 Concept chassis cars and suits tuning sessions that focus on setup refinement rather than major redesign. All 4 posts are used on M and L wheelbase cars, while S wheelbase cars require 2 posts, making the set suitable for different wheelbase configurations within the M-08 platform.
RC tuning parts
M-08 Concept Steering Arms, Aluminum Upgrade
300054891€32.99
The M-08 Concept aluminum steering arms bring a focused handling upgrade to the chassis by replacing the standard steering linkage parts with machined metal components. Each set contains 1 right steering arm and 1 left steering arm, both finished in Tamiya blue anodizing, for a clean mechanical look that stands out clearly during a bench build or maintenance session. The key change comes from the material itself. Aluminum steering arms guide steering movement with greater precision, which the product data describes as leading to more direct steering feel. The parts also offer extremely secure attachment, supported by the threaded mounting points built into each arm. Their dedicated left and right forms are shaped for the M-08 Concept layout, so the upgrade targets the steering system rather than changing unrelated areas of the chassis. This set is intended for use on the M-08 Concept chassis and is recommended for use with the separately sold steering bridge, Item 54892. In a workshop setup, the pair suits drivers refining steering accuracy on an existing chassis build, and on the track the firmer linkage can help inputs feel cleaner through quick direction changes and technical sections. Warning! Not suitable for children under 14 years.
RC tuning parts
M-08/M-07/TA-06 Steel Bevel Gears, RC spare set
300054428€19.79
The M-08/M-07/TA-06 Steel Bevel Gears bring a metal drivetrain upgrade to compatible RC chassis where angled gear transfer is under constant load. Designed to replace the kit-standard GV1 and GV2 gears, this 6-piece set supports running in tougher conditions such as rally driving and use with a high-powered motor. The bevel gear format is used where drive force changes direction inside the transmission or differential area, so gear accuracy and material choice matter directly to how the drivetrain handles repeated stress. These steel parts are intended for a wide range of chassis including M-08 CONCEPT, M-07 CONCEPT, TA06 variants, DB01, TD4, TD2, FF-04 EVO, XV-01 variants and selected TRF platforms. For TA05 ver.II chassis the set is used with 54312, for DB01 with 54329, and for TD4 and TD2 with 54471. As a spare and tuning set for 14 years and up, the gear pack suits rebuilds after wear, planned drivetrain updates, or preparation for rougher surfaces and stronger motor setups. The delivery scope contains 6 bevel gears, making the contents clear for workshop stock, maintenance planning, and chassis-specific parts selection. Warning! Not suitable for children under 14 years.
RC tuning parts
M-08C Rein. C Parts, chassis parts set, 2deg
300054982€12.19
The M-08C Rein. C Parts set brings carbon fiber-reinforced nylon to a key chassis area, giving M-08 Concept running gear a tougher replacement for the standard glass-fiber reinforced parts. Front and rear uprights sit at the center of wheel location and suspension movement, so this material change targets a part of the car that sees repeated load during cornering, contact and recovery after a crash. Inside the set are 2 M-08 Concept C Parts sprues, supplying the component group used for upright and hub carrier assembly. The instruction reference shows 2deg hub carriers with dedicated R and L orientation, plus a 2.5 mm hole that is made in the specified location during assembly. That layout matters when rebuilding worn suspension parts or preparing a fresh chassis, because the mirrored left and right pieces need to sit in the correct direction around the axle and mounting points. The visible shapes also show bearing and pivot openings that connect the upright assembly to the rest of the chassis hardware. This parts set suits routine maintenance, crash repair and planned setup work on compatible cars. It fits M-07 Concept and M-08 Concept models, making it a practical stock part to keep alongside a regularly used RWD chassis when upright wear or impact damage calls for a direct replacement.
RC tuning parts
M0.6 25T Pinion Gear, RC accessory, hard coated
300054578€9.99
This M0.6 25T pinion gear brings a lightweight aluminum construction and a hard coated finish to RC drivetrain maintenance, tuning and replacement work. The newly designed gear uses rounded teeth, so the mesh runs with lower friction loss while the tooth surface is set up for stronger resistance to wear during repeated use. The 25T format suits setups that call for this exact gearing step, and the M0.6 specification matches 06 Module spur gears for correct pairing in compatible transmissions. A 3 mm grub screw is supplied with the gear, allowing the pinion to be fixed to the motor shaft with the intended mounting hardware rather than requiring a separate screw. The stamped tooth count on the face also makes workshop identification quicker when several gearing options are kept together for setup changes. On the bench, it fits naturally into rebuilds, ratio changes and routine parts replacement for RC models that use M0.6 gearing. In running setups, the rounded tooth profile supports efficient power flow through the drivetrain, making this gear a focused choice for racers and builders who keep a close eye on transmission response and component wear.
RC tuning parts
M0.6 Alu.Pinion Gear 23T, motor pinion gear
300054363€10.29
The M0.6 Alu.Pinion Gear 23T is a drivetrain tuning part for compatible RC chassis that pairs a 23-tooth layout with an M0.6 gear module for accurate engagement at the motor side. Its aluminum construction keeps the part light, while the hard-coated finish is applied to the gear surfaces that handle repeated contact under load. Rounded teeth are used here to minimize friction loss as the gear turns, which supports smooth and efficient power transfer through the drivetrain. The set includes the pinion itself and a grub screw for fastening to the motor shaft. Compatibility covers a wide range of chassis named in the data, including TD4, TD2, CR-01, FF-04 EVO, FF-03, M-08 CONCEPT, M-07 CONCEPT, TA08 PRO, TA07 series, TA06 series, TB series, TC-01, TT-02 series and XV series. For TA07 MS Chassis and TA07 MSX Chassis, use is specified with 51356, 51423 and 51548. This gear suits setup changes where a specific tooth count is needed to match motor response and drivetrain balance in a supported model. On bench setup or race-day maintenance, the clearly defined 23T specification makes it easy to select the right pinion for planned gearing adjustments. Warning! Not suitable for children under 14 years.
RC tuning parts
M0.6 Hard Coated Alum. Pinion 27T, RC pinion gear
300054981€9.99
The M0.6 Hard Coated Alum. Pinion 27T brings a focused drivetrain upgrade to compatible RC chassis, combining an aluminum gear body with a hard-coated finish and a 27-tooth layout. In a compact transmission setup, that combination supports smooth power transfer while the metallic gear profile adds a precise mechanical fit at the motor mount. Its M0.6 module specification makes it a dedicated choice for chassis built around that gear standard, and the engraved 27T marking gives a clear tooth reference during setup changes or maintenance. The included 3 x 3 mm grub screw secures the gear on the shaft, keeping installation centered on the actual drive component rather than extra hardware. Teeth are shaped to reduce loss in the mesh with the spur gear, which means the contact point is engineered not only for drive efficiency but also for quieter running. The hard-coated aluminum surface is used here as a functional treatment on the gear itself, where repeated contact places the most demand on the part. This hop-up part suits tuning sessions that compare gearing changes across touring and shaft-driven chassis, and it also fits well into routine rebuilds when a fresh pinion is needed for a known setup. TT-02 and TT-02D chassis require separately sold Item 54500.
RC tuning parts
M03/04/05/06 Lightweight Hollow Shaft, chassis part
300054319€3.39
The M03/04/05/06 Lightweight Hollow Shaft is a stainless steel chassis upgrade for M-03, M-04, M-05 and M-06 platforms. It replaces the kit-standard 5 x 40 mm and 5 x 21 mm shafts that hold the spur and counter gears, bringing a lighter setup to a key point in the drivetrain while keeping the original function of those parts. The set contains 2 shafts, with 1 long and 1 short version to match the specified gear positions. Their hollow construction removes 6 g compared with the standard parts, a focused change that suits builders refining weight distribution through selected components rather than broad changes across the whole chassis. The polished stainless steel finish also gives the parts a clean mechanical look when the gearbox area is opened during maintenance or rebuilds. This upgrade suits workshop use, scheduled replacement of worn running parts, or a fresh chassis build based on the listed M-series platforms. In a tuning session, it fits naturally alongside other drivetrain-focused changes where small weight reductions and exact fit matter at component level. Warning! Not suitable for children under 14 years.
RC tuning parts
MF-01X Ball Bearing Set, chassis accessory, 24 pcs
300054643€49.99
The MF-01X Ball Bearing Set brings a focused drivetrain upgrade to MF-01X chassis cars by replacing friction-heavy rotating points with metal bearings matched to the chassis layout. With 24 pieces in the set, the bearing selection covers the full conversion needed for the kit and supports smoother running during on-road or rally-style sessions. The set includes 20 1150 ball bearings, 2 850 ball bearings and 2 850 flanged bearings, giving the MF-01X platform the specific sizes required at different mounting points. Ball bearings help rotating shafts turn with less drag than plain bushings, which can improve running efficiency across the drivetrain. The flanged bearing format also suits positions where a locating edge is required in the assembly. As a chassis-specific accessory, this set is aimed at builders who want a direct fit rather than a mixed hardware assortment. During maintenance, rebuilds or a fresh MF-01X assembly, the bearing set adds a practical mechanical upgrade that works at the points where wheels and drivetrain parts rotate under load. It suits hobby benches focused on tuning, replacement and keeping an MF-01X car running cleanly over repeated use.
RC tuning parts
Motor Heat Sink, aluminum RC motor cooler blue
300053664€18.99
This motor heat sink adds focused cooling support to compatible RC chassis with a finned aluminum design and a blue anodized finish that stands out clearly in the drivetrain area. The 11 cooling fins increase surface area around the motor can, helping heat move away more efficiently during longer running sessions. The part is made for DF-02, TT-01D TYPE-E, TT-01 TYPE-E and XV-02PRO chassis, giving these platforms a dedicated motor cooling accessory rather than a universal workaround. Its curved form fits the role of a wraparound heat sink, and the single included component keeps replacement or upgrade work straightforward. As a tuning part, it suits builds where motor temperature management matters during repeated acceleration, extended laps or warm running conditions. Mounted in a compatible chassis, the heat sink supports a cleaner thermal setup around the motor area while adding a bright blue hardware accent. It works well for refresh projects, spare-parts boxes and performance-minded RC maintenance where a specific chassis fit is needed.
RC tuning parts
Motor Pinion Gear 20T Aluminum for F201 Chassis
300053509€14.29
This 20T motor pinion brings a focused drivetrain upgrade to compatible RC chassis with a lightweight machined aluminum body, 0.6 module tooth form and a hard fluorine coated surface. The Gun Gray finish gives the gear a technical look, while the engraved 20 marking helps identify the ratio quickly during setup and servicing. The surface treatment combines cemented carbide alumite processing with added fluorine, creating a steel-like strength characteristic together with strong lubricity at the gear mesh. That combination supports efficient meshing between gears and helps limit wear where the pinion meets the spur gear. The part is specified for the F201 chassis and is intended for builders refining gearing to match track layout, motor choice or driving conditions. Depending on the setup, an alternate spur gear size may be required. In use, the pinion sits at the center of the drivetrain, where small gearing changes can alter how power is delivered out of corners and along straights. The scope of delivery includes 1 motor pinion and 2 x 3 mm grub screws for installation on the motor shaft, making this a compact but meaningful tuning part for RC maintenance, replacement or ratio adjustment. Warning! Not suitable for children under 14 years.
RC tuning parts
On-Road Tuned Hard Spring Set, RC chassis springs
300053440€24.99
The On-Road Tuned Hard Spring Set adds a firmer suspension option for RC chassis setups that need more stability at higher speed. This set contains 8 extra hard springs and is intended for a broad range of compatible on-road platforms, making it a focused tuning part for setup work rather than a general replacement. The springs are part of a 4-step range from soft, medium and hard through to EX hard, with color coding in red, yellow, blue and white for quick identification during setup changes. That coding helps keep spring choices clear when comparing handling differences across multiple runs. The extra hard rate improves stability at speed compared with OP163, and the set can widen the adjustment range when combined with other springs from the same range. For TA07 MS chassis, use is specified with 53571. For F104 chassis and F104W chassis, use is specified with 53901. Compatibility spans many established platforms, including F104PRO II, FF-04 EVO, FF-03 PRO, TA06 PRO, TB-Evo.7, TB-04 PRO, TB-03 VDS, TT-02RR, TT-02 TYPE-SR and XV-01 PRO. In practical tuning sessions, that broad fitment supports repeatable suspension experiments across several chassis families while keeping spring selection clearly sorted by rate and color. Warning! Not suitable for children under 14 years.
RC tuning parts
Pinion Gear 26/27T 48P, RC gear set, steel
300054382€16.79
This RC gear set brings 2 tuning options to compatible drivetrains with a 26T pinion gear, a 27T pinion gear and 48 pitch tooth spacing. Made from carburized steel, both gears are designed for repeated contact in the drive system, where clean meshing and consistent fit matter during running sessions and workshop changes. The offset screw attachment holes are arranged in 2 positions, a detail that helps the gears fit motor shafts of different lengths instead of limiting installation to one shaft format. Rounded teeth are used to minimise friction loss at the mesh point, supporting smoother transfer of motor output through the drivetrain. The set is intended for cars equipped with a 48 pitch spur gear, so the tooth profile matches the required spur specification. A grub screw is included for installation, making the set ready for direct use as a replacement part or gearing change. On a bench setup, the 26T and 27T combination allows a quick switch between 2 tooth counts when servicing an RC car or adjusting the drive layout for a different setup. It also works well as a spare set to keep alongside other drivetrain parts for routine maintenance on compatible models.
RC tuning parts
Pinion Gear Coated Alu 22T M0.6, RC gear
300054770€9.99
This 22T pinion gear brings a focused drivetrain upgrade to RC maintenance and tuning work. Made from aluminum and finished with a hard coating, it combines reduced rotating weight with a surface built for repeated gear contact. The M0.6 specification matches 0.6 module spur gears, making the gear pitch clear at a glance when selecting replacement or setup parts. Its rounded teeth are designed to cut drivetrain friction loss while improving resistance to wear. That tooth profile matters at the mesh point, where the pinion transfers motor output into the transmission with every rotation. The 22-tooth count also gives a defined gearing option for builders adjusting acceleration and running characteristics through pinion changes rather than larger drivetrain modifications. A central bore and set screw are provided for mounting the gear onto a shaft. On the bench, this gear fits naturally into rebuilds, ratio changes and routine servicing of compatible RC drivetrains. It works as a direct spare when a worn pinion needs replacement, and it also supports more deliberate setup changes when a transmission is being tuned around a specific motor and spur gear combination. Warning! Not suitable for children under 14 years.
RC tuning parts
Pinion Gear Coated Alu 24T M0.6, RC spare gear
300054771€9.99
The Pinion Gear Coated Alu 24T M0.6 is a drivetrain spare part built for RC model setups that use 0.6 module gearing. Its aluminum body keeps the gear light, while the 24-tooth layout provides a defined gearing option for tuning or replacing a worn motor pinion in an existing transmission. A hard coating covers the tooth surface to handle repeated contact in the gear mesh, and the rounded tooth shape is specified to increase wear resistance while reducing friction loss in the drivetrain. The central bore mounts the gear on the motor shaft, and the included set screw secures it in place for accurate positioning against the spur gear. The 24 marking on the face makes identification straightforward during maintenance or parts changes. This spare gear suits workshop tasks such as refreshing a used RC drivetrain, correcting a damaged pinion, or preparing a matching motor-and-spur combination for the next run. In regular bench maintenance, the compact metal part is easy to sort, inspect and swap when the transmission needs the correct M0.6 pinion again. Warning! Not suitable for children under 14 years.
RC tuning parts
Servo Mount Short, RC chassis accessory, aluminum
300053596€15.49
The Alum. Servo Stays Short is a chassis accessory for TT-01D TYPE-E and TT-01 TYPE-E builds that places a small servo in a lower position. Machined aluminum construction brings high rigidity and accurate fit to this mounting point, helping the steering installation sit neatly within the chassis layout. The set is supplied as 1 short servo mount with 14 pieces. Alongside the aluminum stays, spacers are included for fine adjustment during installation. Those spacers also make it possible to attach a large servo, which broadens the range of compatible steering setups without changing the basic mount. The hardware shown in the set supports the fastening task directly, with washers and screws matched to the mount configuration. In workshop use, this accessory suits rebuilds, tuning work and replacement jobs on compatible TT-01 TYPE-E platforms. A lower servo position can be useful where chassis layout and linkage placement need a more compact arrangement, while the aluminum parts add a clean technical finish to the steering area. Warning! Not suitable for children under 14 years.
RC tuning parts
Suspension Mount Shim Set, RC tuning accessory
300054987€7.19
This suspension mount shim set adds a fast, precise tuning option to an RC chassis setup. The pack contains 20 shims in 2 measured thicknesses, 0.2 mm and 0.3 mm, with 10 pieces of each, so spacing changes can be matched more closely to the handling balance being dialled in at the suspension mount. Each shim uses a U-shaped profile that can be inserted after the mount screw is loosened, which avoids fully removing the fastener during setup work. The forked shape and circular seat help the shim sit around the fixing point in a controlled way, making small geometry changes easier to repeat from one adjustment to the next. The set is designed for use together with washers included in the chassis kit. Shaded and marked parts shown in the fitting diagram are not included in the set. On a workbench, this kind of measured spacing change helps when comparing one suspension setting against another or when refining left and right mount positions in small increments. It suits builders who want quicker access to setup variation during maintenance, testing and chassis tuning, while keeping the adjustment process focused on the mount area rather than a full strip-down.
RC tuning parts
TA-05/IFS Carbon Rein.F Parts, chassis parts
300054031€10.79
TA-05/IFS Carbon Rein.F Parts bring a focused chassis upgrade to compatible RC car builds by using carbon fiber-reinforced resin for the hub carriers. That material choice gives these parts a tougher structure than standard resin versions, with a more direct effect on steering feel when the car is loaded through turns and direction changes. The set is intended for the TA05-IFS and TRF416 chassis and is supplied as 1x F parts tree with 2 components. The paired layout supports left and right installation, matching the mirrored geometry needed at the wheel mounting area. In use, the stiffer carrier construction helps maintain alignment more consistently when the chassis is pushed through fast corner entries, linked bends and repeated steering inputs. This makes the parts relevant not only for replacement after wear, but also for tuning a car toward a more precise front-end response. On a workshop bench, the set suits planned maintenance on a TA05-IFS or TRF416 build where worn carriers are being swapped for reinforced versions. At the track, the sharper steering response can be felt in tighter line control and a cleaner handling balance through technical sections. Warning! Not suitable for children under 14 years.
RC tuning parts
TA-06 Alum. Cup Joint Gear Diff. Unit (2), RC part
300054532€22.29
This aluminum differential cup joint set is made for TA-06 drivetrain tuning, replacing the standard front or rear differential cup joints with lighter metal parts. The 2 output bevel differential cups cut 7.6 g compared with the standard kit joint cups, trimming weight from the drive system where rotating parts matter. Each cup joint works at the differential connection point where drive is passed into the shaft assembly, and the slotted cup form is designed for use with the matching blade parts. Pin protectors are included to reduce wear on the cup and shaft contact areas, which is especially useful in running conditions where repeated drivetrain load can mark the joint surfaces over time. The set is intended for TA06 Chassis, TA06 PRO Chassis and TA06 MS Chassis, giving a focused option for maintenance, replacement or weight-conscious setup changes within that platform family. Use this pair when refreshing a worn front or rear differential connection or when building a TA-06 configuration with closer attention to drivetrain mass. Depending on the chassis setup, a shorter driveshaft may be required.
RC tuning parts
TA-06 Cross Shaft, RC differential spare part
300054311€10.59
The TA-06 Cross Shaft Met. Bevelge.-Diff. is a compact RC differential spare part designed to replace the standard resin cross shafts in the kit-included differential gear unit of the TA06 chassis. The metal construction brings added rigidity to this high-load area and supports smoother operation as the differential turns through acceleration, braking and cornering. The scope of delivery contains 2 cone differential shafts, matching the paired layout used inside the differential assembly. Beyond TA06 fitment, the stated compatibility list extends to TD4, TD2, DB01, FF-04 EVO, M-08 CONCEPT, M-07 CONCEPT, TA06 MS, TA06 PRO, TA05 ver.II, TRF503, TRF211XM, TRF201XMW, XV-01, XV-01 PRO and XV-01T. For TA05 ver.II chassis, this part is used with 54312. For DB01 chassis, it is used with 54329. This spare part suits maintenance work, drivetrain refreshes and targeted upgrades where the differential is already being serviced. The small machined format also makes it a practical bench-stock component for keeping compatible chassis ready for the next rebuild or running session. Warning! Not suitable for children under 14 years.
RC tuning parts
TA-06 Steel Gear Diff. Unit Rear, RC spare part
300054471€40.99
The TA-06 Steel Gear Diff. Unit Rear brings a complete rear differential upgrade together for TA-06 based RC chassis, combining steel bevel gears and metal cross shafts in a drivetrain assembly made for the rear gearbox. Inside the housing, the bevel gears transfer drive across the axle while the cross shafts support the internal gear action, creating the controlled differential movement needed when cornering on track. The set groups the main assembly parts for this rear unit in one place, including a rear gear case set, a gear differential cup joint set, a gear differential gasket, 2 large bevel gears, 4 small bevel gears and a gear cross shaft. The gasket sits between the housing sections to help seal the differential during assembly. Cup joints connect the finished unit to the drivetrain, while the internal gear layout allows the left and right wheels to rotate at different speeds through turns. This makes the set useful for replacing worn parts or building a rear differential with steel internal gears instead of standard components. On TA06, TA06 PRO, FF-03R and XV-01 chassis, the unit suits workshop maintenance, race-day servicing and focused rear-end tuning. For standard FF-03 cars, item 54398 FF03 Gear Case for Gear Differential is required separately.
RC tuning parts
TA-06/XV-01 18 Teeth Alum. Pully, RC spare part
300054450€27.49
The TA-06/XV-01 18 Teeth Alum. Pully is a drivetrain upgrade part for Tamiya TA-06 touring car chassis and XV-01 crossover chassis platforms. Its 18-tooth aluminum construction brings a precise replacement for the standard pulley, while the high-lubricating coating on the surface is designed to improve transmission efficiency and durability during use. The compact assembly adds a focused mechanical change where belt drive performance matters most. The included hardware shown for the assembly consists of the pulley, spacer parts, a metal pin and an E-clip. For the XV-01 platform, the pulley can be installed at both front and rear positions, which supports consistent drivetrain setup across multiple mounting points. The instruction diagram shows the part used in place of the existing 18T pulley on TA-06, making it a direct specification match rather than a tooth-count change. Aluminum spacer elements support the installed position and help complete the pulley assembly as intended for the chassis layout. On a workbench build or maintenance session, this pulley suits focused transmission servicing, replacement of worn drive components, or a planned chassis upgrade. It fits naturally into tuning work where belt movement, rotating efficiency and precise fit are the priority within TA-06 and XV-01 running setups.
RC tuning parts
TA-07 Aluminum Motor Mt Posts, chassis upgrade
300054725€12.29
The TA-07 Aluminum Motor Mt Posts bring a focused chassis upgrade to TA07 PRO cars by replacing the standard motor mount parts with 2 blue anodized aluminum posts. Positioned at the main motor plate, these parts increase rigidity at a key mounting point, which helps support the motor more firmly when higher powered setups place greater load on the drivetrain. Each post is designed for use in place of part A15, making the change specific and direct rather than a broad rebuild. The machined aluminum shape creates a more solid attachment point than the standard resin pieces, and the anodized finish adds a clean technical look that matches performance-oriented tuning parts. The installation diagram specifies correct orientation and straight screw fitment, with thread lock applied during assembly. That detail matters at this location, where alignment at the motor plate affects how securely the parts seat against the chassis hardware. On a TA07 PRO build, this kind of upgrade suits drivers refining a car for stronger motor output and more controlled power delivery. It fits naturally into workshop sessions focused on drivetrain tuning, chassis response and targeted parts replacement, especially when a standard mounting point is being upgraded for a stiffer setup.
RC tuning parts
TA-07/TB-05 Soft Stabilizer Set for RC Chassis
300054979€35.49
The TA-07/TB-05 Soft Stabilizer set adds a focused suspension tuning option for compatible RC chassis cars by supplying 6 stabilizer bars with stepped stiffness choices for front and rear use. Front bars are included in 1.3 mm, 1.2 mm and 1.1 mm sizes, while rear bars come in 1.2 mm, 1.1 mm and 1.0 mm sizes, making it possible to adjust roll characteristics with a measured hardware change rather than broad setup guesses. The set uses stabilizer ends with integrated adjusters, a detail that keeps the assembly light and simplifies trackside setup work. That construction helps when comparing front-to-rear balance across repeated laps, because the bars can be fitted and adjusted with a direct mechanical reference. The included range supports fine changes instead of a single large step, which is useful when a chassis needs a narrower setup correction for changing grip levels or a specific circuit layout. Compatibility is stated for TA07, TB-05 and TRF420 chassis cars, placing the set squarely in the tuning category for on-road RC running. On practice days, club races or timed sessions, the different bar options support back-to-back testing through fast corners, linked direction changes and tighter infield sections where small setup differences can show up in lap consistency.
RC tuning parts
TA02/01 Alum. Motor mount Set, model accessory
319804966€35.49
The TA02/01 Alum. Motor mount Set adds a machined aluminium mounting solution to compatible model builds, centring the motor base around a circular plate with a wide middle opening and a ring of evenly spaced holes. This layout supports careful positioning during repair, replacement or tuning work and gives the drivetrain area a clean, technical fit. Alongside the main plate, the set uses threaded cylindrical spacers, a flanged adapter piece and a countersunk Phillips screw to create the motor base assembly. The metal parts shown in silver are shaped for screw-fastened installation, with countersunk openings that let the screw sit flush in the mount. The threaded sections support neat connection between the individual components, while the different spacer forms help establish the required stand-off and mounting height within the chassis area. On the workbench, this hardware suits rebuilds, maintenance sessions and targeted upgrades where a worn or standard motor base is being replaced with aluminium parts. The compact set focuses on the mounting zone itself, making it a practical choice for model hobby setups that need precise motor support rather than decorative add-ons.
RC tuning parts
TA08 Carbon Damper Stays FR, RC chassis parts
300022005€28.49
TA08 Carbon Damper Stays FR adds a focused suspension tuning option to compatible TA08 chassis cars with 2 carbon stays for the front and rear. Each stay is 3 mm thick and uses a lightweight plate format with multiple mounting points, giving the chassis a clear path to more precise damper geometry changes during setup. The front stay provides 4 damper attachment positions, while the rear stay provides 5, so adjustments can be made separately at each end of the car instead of relying on a single fixed mounting location. The set also contains 4 hex head screws in 3 x 6 mm size for installation. The carbon construction and machined hole layout suit builders who want to work directly with suspension settings and compare different damper angles on the same TA08 platform. On a bench setup, the different attachment points support careful testing of front-to-rear balance before the next run. At the track, the front and rear stays allow repeated setup changes with the same chassis base, making this set a useful choice for drivers refining handling on compatible TA08 cars.
RC tuning parts
TA08 LF King Pin Balls, RC chassis option parts
300022016€12.69
TA08 LF King Pin Balls bring a focused suspension upgrade to compatible RC chassis cars by replacing the standard 7 mm suspension balls and king pins with 4 low-friction aluminum components. The hard anodized finish changes the contact surface from the kit-standard steel setup and supports a more rigid suspension point where the upright moves through its travel. Each king pin ball reduces weight by about 0.4 g, trimming unsprung mass at a part of the chassis that reacts directly to steering and surface input. That reduction is small in absolute terms but meaningful at the suspension, where lighter moving parts can help the car settle more quickly and track more consistently through repeated corner entries. The set can be installed at either the front or rear, using 1 king pin ball at the top and bottom of each upright. Compatibility is stated for TC-01 and TA08 PRO chassis cars. A full setup for 1 kit requires 2 sets. When fitting this Hop-Up Option, new 51663 TC-01 C/D Parts Suspension 2 pcs and 51669 TA08 D Parts Suspension Arms 2 pcs are recommended. This makes the set a targeted choice for tuning an existing chassis with a clearly defined suspension change rather than a general-purpose hardware pack.
RC tuning parts
TA08 LW Front One-Way 37T, chassis upgrade set
300022039€66.99
The TA08 LW Front One-Way 37T is a chassis upgrade set for selected Tamiya on-road cars, built to alter front drivetrain behavior with a dedicated one-way mechanism. Installed at the front, the unit leaves the front wheels unbraked during deceleration, which changes how the car responds when power is applied and when entering corners. At the center of the set is an aluminum one-way housing paired with a slim lightweight 37T pulley. That layout focuses on a compact rotating assembly at the front end, while the included cup joints, urethane bushings and 3x5 mm hex head screws provide the hardware needed for the conversion. The one-way action is a mechanical tuning change rather than a cosmetic add-on, aimed at drivers refining acceleration response and corner entry on belt-driven chassis layouts. Compatibility is stated for TA08 PRO, TA07 and TRF420 chassis cars. This kind of front setup suits track sessions where steering response and exit speed are being tuned corner by corner. In workshop preparation or race-day maintenance, the set gives experienced builders a defined 37T front one-way option for platform-specific drivetrain adjustment.
RC tuning parts
TA08 Stabilizer Set F/R, chassis accessory kit
300022003€38.49
The TA08 Stabilizer Set F/R adds a focused suspension tuning option to compatible TA08 chassis cars by supplying front and rear anti-roll bar parts in 2 stiffness levels. Super soft green stabilizers and soft red stabilizers are both included, making it possible to alter roll response at each end of the chassis and match the car more closely to track grip and corner balance. The set contains long Open Face 5 mm reinforced adjusters, 5 mm stabilizer end adjusters, aluminum stabilizer rod supports, 5x10 mm aluminum hex head ball connectors, 630 ball bearings and 3x2.5 mm grub screws. That hardware gives the bars their mounting points and link connections while the bearings help the mechanism move smoothly through suspension travel. Using 2 front and 2 rear stabilizers keeps the setup specific to both ends of the TA08 layout rather than treating the chassis as a single undivided system. On a technical indoor layout or a higher-grip circuit, the different bar rates can be swapped to explore how the car settles into turns, changes direction and carries speed through linked corners. As a workshop upgrade, this set suits drivers who tune handling step by step and want a dedicated stabilizer package matched to the TA08 platform.
RC tuning parts
TA08R/Pro Alum. Diff.-Mount +0,5, RC chassis part
300022079€28.49
These aluminum differential holders are an option part for the TA-08 platform and related touring car chassis, adding a more rigid mounting point around the differential area while supporting accurate belt tension adjustment. The set contains 2 holders and uses a +0.5 specification that changes differential position compared with the standard layout. The rigid aluminum parts are designed to hold the adjustment notch securely, which helps the belt setting stay consistent under load. Their shape also supports smooth rotation at the differential area and improves rigidity where the holders connect with the bulkheads. In that section of the chassis, oil damper motion is transmitted more directly to the main structure, which can help the suspension response stay more faithful to the setup. Laser engraving distinguishes these holders clearly from Item 22079, which uses a different offset. Compatibility covers TA08R, TA08 PRO, TRF420X and TRF420 chassis. Depending on surface conditions, the alternative 0.5 mm offset holder arrangement can be relevant for setup tuning, and a raised differential position is stated to stabilize the car on high-grip surfaces. On a prepared track, that gives builders another precise chassis setting to match grip level and drivetrain feel.
RC tuning parts
TA08R/Pro Alum. Diff.-Mount +0.8, chassis option part
300022078€28.49
These aluminum differential holders are a focused chassis upgrade for TA08R, TA08 PRO, TRF420X and TRF420 builds. The 2-piece set adds a 0.8 mm offset and gives the differential section a rigid mounting point, while the integrated notch works with belt tension adjustment for a more exact drivetrain setup. Under load, the aluminum construction helps limit deformation at the connecting sections with the bulkheads. That added rigidity supports smooth differential rotation and helps oil damper motion transfer properly into the chassis, so suspension input is carried more directly through the assembly. Laser engraving distinguishes this version clearly from Item 22079, which uses a 0.5 mm offset. Depending on surface conditions, that alternative offset can also be used as part of setup tuning. On high-grip surfaces, differential height becomes an important setup variable, and raising the differential can stabilize the car. That makes these holders a useful option when refining belt tension, comparing offset choices and preparing a TA08R or TRF420 platform for track-specific handling changes.
RC tuning parts
TA08R/Pro Alum. Motor Mount, chassis option part
300022081€39.99
The TA08R/Pro Alum. Motor Mount is a chassis option part for TA08 PRO and TA08R platforms, built around a 3.0 mm TA08R aluminum motor plate and matched mounting hardware. Its machined form and countersunk screw positions suit precise installation in the motor area, where fit and alignment matter during a rebuild or tuning update. The set contains 1 aluminum motor plate, 2 aluminum upper deck mounts and 2 countersunk 3x6 mm hex head screws. The blue anodized finish gives the metal parts a clear technical look while keeping the focus on the component geometry, including the cutouts and mounting points needed for the chassis layout. As an option part, this set is aimed at maintenance, replacement or setup changes on an existing compatible chassis rather than a complete vehicle build. Used during workshop servicing or a focused chassis refresh, the parts support a direct hardware update on TA08 PRO and TA08R assemblies. The compact contents make it suitable for racers and model builders who keep specific spare and tuning parts ready for platform-based maintenance. Warning! Not suitable for children under 14 years.
RC tuning parts
TA08R/Pro Rear Upper Arm Mount Set, RC chassis part
300022084€60.79
This aluminum rear upper arm mount set is an option part for the TA08R and TA08 PRO chassis, supplying 2 mirrored pieces for the left and right sides of the rear assembly. The machined shape, multiple mounting holes and slotted section create a precise interface where the upper arm area meets the chassis, giving builders a focused upgrade for this section of the car. The set is described as a chassis aluminum rear upper arm mount and is intended for model tuning rather than general replacement across unrelated platforms. Its geometry is specific to the TA08 family, and the pair format ensures the rear section receives matching hardware on both sides. Dedicated attachment points also support the separately sold TA08R Carbon Upper Deck in 2.0 mm thickness, which opens an additional configuration route for builders working with TA08R-based layouts. During bench setup, the design allows easier attachment and detachment of upper arm ball connectors, which is useful when rear suspension parts need to be accessed repeatedly for maintenance or adjustment. Compatibility is stated for the TA08 PRO and TA08R chassis, making this set a direct fitment choice for those specific platforms. Warning! Not suitable for children under 14 years.
RC tuning parts
TA08R/Pro Rein. Rear Body Mounts, chassis option part
300022085€28.29
This rear body mount set is an option part for TA08R-based chassis setups and brings the key hardware for a focused shell mounting update into one pack. The set combines 2 carbon fiber bases with 2 aluminum posts, creating a rear mounting structure that supports accurate body placement and a tidy fit around the shell line. The included body mount extensions, carried over from Item 54604, allow mount height adjustment according to the body in use. That makes the set useful when shell shapes or mounting positions differ, because the rear posts can be set to suit the body rather than forcing a fixed height. Small hardware is also supplied for installation, with 2 3x6 mm hex head screws, 2 3 mm washers and 2 7 mm snap pins completing the package. The mix of carbon fiber, aluminum and fastening parts keeps the upgrade centered on the rear body mounting area instead of spreading across unrelated chassis sections. Compatibility is stated for the TA08 PRO, TA08R and TB Evo.8 chassis, making this set a direct choice for those platforms when rear shell mounting needs replacement or adjustment. On a finished RC touring car, that can help when setting body height and securing the shell cleanly at the rear mounting points. Warning! Not suitable for children under 14 years.
RC tuning parts
TA08R/Pro Upper Arm Mount Set, aluminum chassis part
300022083€60.79
This aluminum front upper arm mount set is made for the TA08 PRO and TA08R chassis and supplies a matched left and right pair for the front section. The mirrored parts use a hole pattern and slotted geometry shaped for the chassis connection area, giving the assembly a dedicated option part focused on front-end tuning and maintenance access. A key function of the set is its provision for the separately sold TA08R Carbon Upper Deck in 2.0 mm thickness. The added attachment points make that deck compatible with this mount layout, which is useful for builders refining a TA08R or TA08 PRO setup with model-specific chassis parts. The aluminum construction brings a precise machined look to the front assembly, while the left and right format keeps the installation matched across both sides. Content is 2 pieces. During workshop use, the easier attachment and detachment of upper arm ball connectors can simplify repeated setup work at the front end. That matters when camber or suspension-related adjustments call for frequent access around the upper arm area. As an option part rather than a universal accessory, this set is intended specifically for TA08 PRO and TA08R chassis builds and upgrade projects. Warning! Not suitable for children under 14 years.
RC tuning parts
TB Evo.IV/TRF416 D-Parts, suspension arm set
300051104€17.29
The TB Evo.IV/TRF416 D-Parts suspension arm set is a dedicated carbon spare part for selected RC touring car chassis, built to restore the correct fit where suspension components take repeated load. Supplied as 1 D-parts set with 2 parts, it gives a direct replacement route for maintenance work on compatible platforms. Fitment covers FF-03, FF-03 PRO, TA05 Ver.II, TB-04, TB-04 PRO, TB-03, TB-03 VDS, TT-02 TYPE-SR and TT-02 TYPE-S chassis. That wide chassis coverage makes the set useful for keeping several workshop builds in service with the same reference part. The suspension arm shape uses defined mounting holes and cutout sections to match the intended chassis layout. In running gear assembly, this kind of component links key suspension points and helps preserve the geometry set elsewhere on the car. On the bench, the set supports routine replacement after wear, damage or a full teardown. It also suits planned rebuilds where the correct D-parts are needed before the next setup session, helping compatible chassis return to smooth, consistent operation with the intended arm structure. Warning! Not suitable for children under 14 years.
RC tuning parts
TB-04 Bevel Gear Set, RC chassis spare parts
300054593€7.19
This TB-04 bevel gear set brings carbon fiber-reinforced resin construction to a key drivetrain area, giving TB-04 chassis cars gears that are more resistant to wear and suited to use with higher-powered motors. The set is made up of 3 matched transmission parts that work together where rotational force changes direction inside the chassis. A 40T ring gear handles the larger driven stage, while the 16T bevel gear and 20T miter gear complete the meshing set for the TB-04 layout. The angled teeth on these gears are designed to engage under load as the drivetrain transfers power through the chassis, making correct fit and matched tooth contact especially important. Because the parts are specified as a set, installation as a complete group helps maintain the intended relationship between the gears rather than mixing single replacements into an existing worn setup. This spare parts set suits maintenance, repair and drivetrain refresh work on compatible TB-04 chassis cars. It fits naturally into workshop sessions focused on restoring clean gear action after running with stronger motor setups or replacing worn internal transmission parts with the correct matched components.
RC tuning parts
TC-01 Alu. Steering Arms L/R, RC chassis parts
300054958€35.99
The TC-01 Alu. Steering Arms L/R brings a focused steering upgrade to TC-01 chassis cars with a left and right aluminum arm set finished in blue anodizing. Designed as a hop-up option for the freshly released TC-01 platform, these parts support smoother handling while giving the front steering assembly a more precise mechanical feel. The set replaces the kit-standard components T4 and T7, using lightweight aluminum parts in their place at a key point in the steering mechanism. That material change gives the mounting area a more secure attachment and adds a more direct response through steering inputs. The machined shape and mounting holes are tailored to the TC-01 layout, so the upgrade stays specific to the chassis it is made for instead of relying on a generic fit. For a matching setup within the same steering area, use with the aluminum steering bridge in item 54957 is recommended. On the bench, this pair suits builders refining a TC-01 car with selected metal hop-up parts rather than changing the whole chassis at once. Bearings are not included, so the set can be planned into a build, maintenance session, or steering refresh with the required hardware already on hand.
RC tuning parts
TC-01 Alu. Steering Bridge, chassis hop-up part
300054957€28.79
The TC-01 Alu. Steering Bridge is a focused hop-up part for TC-01 chassis cars, replacing the kit-standard T9 component with a precision aluminum bridge that adds rigidity to the steering area and supports smoother handling. Its blue anodized finish gives the machined part a clear visual identity while matching the technical character of a tuned chassis build. The bridge is supplied as 1 aluminum component and is designed to sit between the steering parts shown in the TC-01 layout. The mounting holes and central slot allow accurate positioning during installation, while shim adjustment can be used to set clearance so the steering bridge and arms move smoothly. The instruction data also recommends gel type thread lock on the screws to help prevent loosening, and 630 ball bearings are recommended for the steering assembly. Recommended for use with the aluminum steering arms in Item 54958. Compatible with TC-01 chassis cars. On a bench build, this part suits targeted chassis tuning where the steering system is being refined one section at a time. In running sessions, the added rigidity and cleaner steering movement support a more settled response through direction changes on a TC-01 setup.
RC tuning parts
TC-01 Alum. Damper Extenders, chassis hop-up set
300054960€9.29
TC-01 Alum. Damper Extenders bring a focused suspension upgrade to TC-01 chassis cars with 4 lightweight aluminum components shaped for damper mounting. The blue anodized finish gives the set a crisp technical look while the precision-machined construction targets a more exact hardware fit in a high-spec chassis setup. As a Hop-Up Option, this set is aimed at builders refining how the suspension is configured rather than changing the character of the whole car at once. Each extender replaces the kit-standard version with an aluminum alternative, shifting this area of the assembly from standard molded hardware to machined metal parts. That makes the set a clear tuning step for TC-01 builds where damper function and suspension detail matter. The pack contains 4 matching extenders, allowing the same specification to be carried across the chassis instead of updating only one corner. On the bench, the set suits planned rebuilds, fresh TC-01 assemblies, or targeted suspension revisions between running sessions. The matched parts and chassis-specific compatibility make it a straightforward choice when the goal is a cleaner, more consistent damper setup on a TC-01 platform.
RC tuning parts
TC-01 Alum. Rocker Arms, chassis hop-up parts
300054955€19.99
The TC-01 Alum. Rocker Arms (2) bring a focused suspension upgrade to TC-01 chassis cars by replacing the kit-standard rocker arms with lightweight aluminum parts. Their higher rigidity reduces flex at the linkage, which helps the suspension react with a more direct feel when the chassis loads and unloads through corners, braking and acceleration. Each set contains 2 aluminum rocker arms and is intended as a hop-up option for builders refining the suspension character of a TC-01 machine. The change in material affects how force passes from the suspension linkage into the dampers, so damper action feels cleaner and more immediate than with the standard molded parts. The blue anodized finish adds the familiar technical look associated with Tamiya tuning parts while also marking the upgrade clearly during maintenance and setup. This set suits targeted chassis tuning, whether the goal is a sharper response on a prepared track or a more defined suspension feel during test sessions in a car park. For a complete front and rear rocker arm conversion on 1 car, 2 sets are required.
RC tuning parts
TC-01 DblCrd Prop Shaft, chassis hop-up part
300054961€35.99
The TC-01 DblCrd Prop Shaft is a dedicated hop-up part for TC-01 chassis cars, built to support more efficient drive with a double cardan layout that maintains true rotation across a range of operating angles. Crafted in steel, the shaft replaces the kit-standard propeller shaft parts with a more rigid driveline component suited to tuning the chassis around its moving suspension geometry. The set is supplied as parts for assembling 1 shaft, not a full front and rear conversion. That makes it a focused upgrade for builders working on a specific driveline position first, while keeping the option to match the chassis with a second set later. The included shaft length shown in the documentation is 54 mm, and the assembly uses joint pieces, pins and axle rings to create the finished rotating linkage. The double cardan mechanism is especially relevant where the shaft must transmit power cleanly while the angle changes through steering and suspension movement. Installed on a TC-01 car, this hop-up part suits workshop tuning sessions that concentrate on driveline efficiency rather than cosmetic changes. It also fits rebuilds where worn standard parts are being replaced with a steel alternative matched to the chassis platform.
RC tuning parts
TC-01 Stabilizer Set, RC chassis option parts
300054956€27.29
The TC-01 Stabilizer Set adds a focused suspension tuning option to TC-01 chassis cars by introducing sway control that supports steadier cornering balance. With 3 rod rates in 1.1 mm, 1.2 mm and 1.3 mm, the set gives a clear path to adjusting chassis response for different surfaces and driving styles while keeping the installation compact within the car layout. Each rod sits between the upper cover and the chassis, where clearance can be adjusted via 3 x 3 mm grub screws. Aluminum hex head ball connectors make setup changes easier when comparing different stiffness choices. The black rods use red, yellow and blue markings so each rate can be identified quickly during bench work. The stabilizer can be installed at the front or the rear, which allows targeted tuning of entry feel and mid-corner balance on a TC-01 build. On practice days or race preparation sessions, the set supports back-to-back setup testing with a direct hardware change rather than a full suspension redesign. One set equips either the front or the rear; 2 sets are required to complete one car with front and rear sway bars. Compatible with TC-01 chassis cars.
RC tuning parts
TC-01/TB Gear Different, aluminum shaft set
300054533€9.99
This shaft set is made for the TC-01/TB gear differential and supplies 2 matching aluminum parts for maintenance, repair or parts replacement in a model drivetrain. The compact format and dedicated fit make it a focused choice when a differential assembly needs the correct metal component rather than a generic substitute. Each piece has a cylindrical profile with a darker central hex section, indicating a layout designed to locate securely within the relevant differential area during assembly. Aluminum construction keeps the parts light while providing the crisp, machined character expected for RC model hardware. Because the set contains 2 identical shafts, both sides of the intended mechanism can be refreshed with matching components instead of mixing old and new drivetrain parts. In workshop use, this kind of spare is well suited to routine servicing, rebuilds after heavy running sessions, or keeping essential replacement parts on hand between maintenance intervals. It also fits neatly into a planned parts stock for TC-01/TB based builds where drivetrain condition and exact component matching are part of careful setup work.
RC tuning parts
TC-01/TB-04 Gear Diff. Steel Bevel Gears
300054540€20.49
TC-01/TB-04 Gear Diff. Steel Bevel Gears are drivetrain spare parts for compatible Tamiya chassis, centered on the internal gear differential where controlled power distribution depends on clean, accurate gear engagement. The steel construction gives these bevel gears the material specification stated for the set, making them suited to differential rebuilds and scheduled parts replacement on used running gear. Within a gear differential, bevel gears work at the core of the mechanism, transferring drive through meshing angled teeth while allowing the left and right sides of the axle system to rotate at different speeds in turns. That makes this set relevant when a TC-01 or TB-04 build shows wear in the diff internals or when a fresh drivetrain setup is planned during maintenance. The designation covers 2 chassis families, so the parts can be matched directly to those platforms instead of relying on generic hardware. As a model supply in the Models & Accessories range, the set is aimed at repair, upkeep and chassis-specific workshop use. On the bench, these gears suit routine differential servicing, a full gearbox refresh, or a rebuild after extended running. They also fit neatly into a spares box for future maintenance on TC-01 and TB-04 cars, where having the correct internal metal gears on hand helps keep a project moving without delay.
RC tuning parts
TD4 Aluminum Steering Arms, RC car accessory
300022033€39.99
These TD4 aluminum steering arms are a focused chassis upgrade for TD4 cars, combining machined metal construction with built-in ball bearings to sharpen steering feel at the front end. The set includes a left arm and a right arm, each shaped for its position, with the blue anodized finish giving the parts a clean technical look once fitted on the chassis. The aluminum structure keeps weight low while providing firm attachment at the mounting points, which helps the steering linkage transmit input with a more direct response. Built-in ball bearings support the pivot area and promote smoother movement through the steering action. The long cutout profile and compact arm shape reflect the purpose of the part: reducing excess mass while keeping the component ready for repeated running sessions on a TD4 platform. Installed on a TD4 chassis car, the pair suits maintenance, repair or a move from standard parts to a metal steering setup. The matched left and right layout keeps the front steering assembly consistent, whether the goal is restoring worn hardware or refining the control feel of an active RC buggy.
RC tuning parts
TD4 Ball-Diff. Nut/Screw Set, RC spare parts
300022029€11.29
The TD4 Ball-Diff. Nut/Screw Set brings together the small mechanical parts used in a TD4 ball differential, giving RC model maintenance a focused hardware pack instead of a search through mixed workshop stock. The set contains a shouldered screw, a coil spring, washers, a blue metal retainer piece and 8 steel balls, all centered on the differential assembly shown in the designation. Within a ball differential, these parts work as a pressure and contact system: the spring loads the assembly, the screw provides the fastening point, the washers sit between moving or clamped surfaces, and the steel balls form the running contact elements inside the mechanism. That combination matters when a differential needs fresh hardware after wear, disassembly or a lost part during service. The blue anodized component adds a dedicated fitted part to the set rather than relying only on generic screws and washers. On the bench, this kind of pack supports a clean rebuild of the TD4 differential with the exact group of small components kept together in one place. It suits routine maintenance sessions, targeted repairs after drivetrain wear, or preparation of a spare parts box for future servicing on a compatible RC chassis.
RC tuning parts: get the best out of your RC model!
With RC tuning parts, you can give your vehicle a personal touch and take its performance to the next level. Whether you want to make your RC car faster, more stable, or visually unique – you'll find the right tuning options with us to make your hobby even more exciting.
Why RC tuning parts are a must for your model
More performance, more driving fun
With the proper RC tuning parts, your model will not only stand out visually, but it will also have significantly improved driving characteristics. RC aluminium tuning parts such as shock mounts and wheel axles provide more stability and durability, ensuring you maintain full control even at high speeds or on rough terrain. Additionally, specialised motor pinions or servo mounts allow you to increase acceleration and precision. This means: even more adrenaline with every race!
Visual customisation
RC tuning isn’t just about performance – it’s also a way to make your model unique. With stylish tuning parts made from aluminium or other high-quality materials, you can give your RC car a truly personal touch. Whether it’s vibrant colours, cool rims, or custom body parts – your RC model is guaranteed to turn heads on the track.
The joy of building and optimising
A key part of RC model building is the enjoyment of tinkering and customising. With the right RC car tuning parts, you can adjust the driving behaviour to suit your needs and get immediate feedback on your work – a rewarding experience that is sure to thrill! From improved control arms to special wheel hubs: every tuning part brings your model closer to perfection.
Find the right RC tuning parts for your model
Excited to try RC tuning? Then browse through our selection and discover high-quality RC tuning parts for your model. Whether you're looking for RC aluminium tuning parts or specific components for your vehicle – we offer a wide range that makes RC car tuning a real adventure. Make your model unique and feel the difference with perfectly matched tuning parts.