RC spare parts
Discover first-class RC spare parts from Tamiya. Screws, shock absorbers, drives and much more! If you want to find out more, you can read on here.
Other spare parts & accessories
10mm Shim Set, RC accessory, 0.1-0.3 mm spacers
300053588€13.49
This 10 mm shim set brings fine mechanical adjustment to RC chassis work, with 30 spacers sized at 10 mm inner diameter and 13 mm outer diameter for controlled spacing at shaft mounting points. The 3 thickness options of 0.1 mm, 0.2 mm and 0.3 mm make it possible to correct small gaps that can lead to unwanted movement in suspension or wheel axle assemblies. Instead of relying on a single washer size, the set gives stepped tuning options that suit different setup needs across on-road and off-road vehicles. Each shim can be placed to shift the position of a mounted part in small increments, including forward adjustment where the chassis layout calls for tighter spacing. That makes the set useful during maintenance, rebuilds and race-focused setup changes where alignment and reduced slippage matter. Scope of delivery: 1 spacer set with 30 pieces. On the bench, the assortment supports careful fitting of moving parts before a run. During a rebuild or handling-focused setup session, the different shim thicknesses help dial in cleaner spacing at the exact point where play needs to be reduced. Warning! Not suitable for children under 14 years.
Axes & drive shafts
12 mm Wheel Hub Hexagon Set, RC chassis accessory
300053056€10.59
This 12 mm wheel hub hexagon set brings a clean aluminium upgrade to the wheel mounting area on a wide range of RC chassis. The pin-type design pairs each hex hub with a matching pin, creating the interface that transfers drive from the axle to the wheel while keeping the fit consistent during assembly, maintenance and parts replacement. The scope of delivery includes 4 wheel hub hexagons and 4 pins. The aluminium construction gives these small drivetrain parts a crisp machined look, and the 12 mm hex format matches the standard wheel mounting size used across many compatible on-road and off-road platforms. Fitment listed in the data covers CR-01, DF-03, DF-02, DT-03, DT-03T, DT-02, F103GT, M-06, M-06 PRO, M-05, M-05 PRO, M-05 ver.II PRO, MF-01X, TT-02B, TT-02FT, TT-02RR, TT-02D, TT-02 TYPE-SR, TT-02 TYPE-S, TT-02, TT-01D TYPE-E and TT-01 TYPE-E chassis. For workshop stock, rebuilds or replacing worn wheel mounting parts, this set covers one full chassis with 4 matching hubs and pins. It suits bench work where exact chassis compatibility matters and keeps the wheel mounting hardware aligned with the specified 12 mm standard used by the listed platforms. Warning! Not suitable for children under 14 years.
Gears & motor pinions
19T Pinion Gear, model accessory, M0.6
303505049€5.69
This 19T pinion gear is a compact drivetrain part for model applications that use module M0.6 gearing. Its 19 straight teeth mesh with the matching gear stage to pass motor rotation into the transmission, making it a functional choice when a specific tooth count is needed in the drive layout. The dark metal gear body is shaped for shaft mounting, with a central round bore and a side set-screw hole visible on the part. The top surface is marked with 19, which helps distinguish this version from other tooth counts during maintenance or parts sorting. As a small mechanical component, the pinion sits at the point where motor output meets the rest of the drivetrain, so the tooth count directly relates to the gearing combination used in the model. It fits naturally into workshop tasks such as replacing a worn pinion, restoring a compatible drivetrain, or keeping a matching spare ready for service intervals. On the bench, the compact form and visible marking make it straightforward to identify alongside other transmission parts and gearing options. Warning! Not suitable for children under 14 years.
Gears & motor pinions
20/21T Pinion Gear Set, RC motor accessory, aluminum
300050356€9.99
This 20/21T Pinion Gear Set is a compact drivetrain upgrade for compatible RC chassis, pairing 2 aluminum pinions with 2 grub screws for secure mounting on the motor shaft. The 20-tooth and 21-tooth options give a clear gearing choice when replacing worn parts or adjusting the drive layout for a specific chassis setup. The machined aluminum construction keeps the focus on precise tooth engagement and clean fitment in model drivetrains that use module 0.6 gearing. One pinion is marked 20 for quick identification during setup, which helps separate the two ratios at the workbench. The set is intended for a wide spread of Tamiya platforms including M-05, M-05 PRO, M-05 ver.II PRO, M-06, M-06 PRO, WR-02, WR-02G, WR-02CB, GF-01, GF-01TR, GF-01CB, G6-01, G6-01TR and TB-05 PRO. It also supports CC-01 with 20T only, plus TA06, TA06 PRO, TA06 MS and TC-01 with 21T only. Additional chassis-specific notes are defined for several applications: DF-02 is used with 53703, F104PRO II is used with 51609, and TA07 MS is used with 51356, 51423 and 51548. That makes the set a practical spare or tuning part for keeping compatible RC cars running with the correct motor pinion combination. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
2mm C-Ring-Set, model accessory, 8-piece
300084171€2.19
This 2 mm C-Ring-Set supplies 8 matching retaining clips for model maintenance, repair work and parts replacement. The compact format suits assemblies that use small fastening points, where a C-shaped ring locks into a groove on a shaft or similar mounting point to hold parts in position. The set groups identical metal clips together, which helps when a rebuild calls for consistent replacement parts rather than mixed hardware. The open centre cutout allows each ring to snap into place on the intended fitting, making this type of fastener useful wherever a low-profile retainer is needed in a mechanical model assembly. The silver-coloured finish also makes the pieces easy to identify in a parts tray or workshop setup alongside screws, washers and other small hardware. Used as spare parts, these C-rings support routine servicing, careful restoration work and the replacement of missing retainers in existing builds. Kept in a hobby drawer, the 8-piece pack provides a practical stock of matching clips for future workshop tasks on compatible model mechanisms. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
2mm E-Ring Satz, model accessory, 15 pieces
300050588€3.09
This E-Ring Satz provides 15 matching retaining clips in a 2 mm size for model maintenance, repairs and mechanical assembly work. Each E-ring is made as a small stamped metal fastener that presses onto a grooved shaft or axle from the side, where it acts as a stop to hold mounted parts in place. The flat clip profile keeps the fastening point compact, which is useful in tight spaces around driveline and wheel assemblies. The pack suits jobs where worn or missing retaining hardware needs a direct replacement in the correct size. A 2 mm E-ring can be used wherever the assembly calls for this specification, including axle or shaft setups that carry gears, bushings or wheels. The 2 mm thickness stated in the data adds a clear reference point when matching spare hardware to an existing build. With 15 identical pieces in one set, the supply supports repeated service work and keeps consistent hardware ready for future rebuilds. On the workbench, these clips fit naturally into parts sorting trays, spare hardware boxes and routine maintenance kits for RC and scale model projects. They are especially useful when a rebuild calls for several matching retainers across multiple connection points or when a small clip needs quick replacement after disassembly. Warning! Not suitable for children under 14 years.
Screws & ball head screws
2mm/M2 Lock Nut Mini 4WD hardware set
300094690€4.99
This hardware set brings 10 compact M2 lock nuts into Mini 4WD maintenance, repair and fresh assembly work. The 2 mm format suits small threaded connections, while the lock-nut construction with a nylon insert ring is designed to hold more firmly once tightened, a useful detail on fast-moving model assemblies where vibration can work against standard fasteners. The close-fitting hex shape supports careful tool use on small parts, and the metal finish gives each nut a clearly defined edge during installation. Keeping matching M2 hardware together also helps maintain a consistent fit across repeated rebuilds, part swaps and setup changes. Because the pack contains 10 pieces, it covers multiple fastening points and leaves spares ready for later workshop use. The set is focused, simple and specific: small fastening hardware for Mini 4WD systems where the right thread size matters. On the bench, these lock nuts suit routine replacement after wear, rebuilding a chassis with fresh hardware, or keeping spare fixings ready in a parts box between race-day adjustments. They also fit neatly into a regular stock of model workshop essentials, alongside the screws, shafts and brackets used in ongoing Mini 4WD upkeep. Warning! Not suitable for children under 14 years.
Screws & ball head screws
2x8mm Differential Tapping Screws, model spare set
300050573€3.29
This spare screw set focuses on one specific workshop need: 10 matching 2x8 mm differential self-tapping screws for compatible model maintenance and repair. The uniform size keeps replacement work consistent when original fasteners are worn, missing or set aside during a rebuild, and the metal construction suits repeated use in model assembly tasks where a precise screw type matters. The domed heads use a crosshead drive, allowing the tool to seat cleanly during installation and removal. A fully threaded shaft is suited to fastening duties where the thread needs to bite along the full length of the screw rather than only near the tip. Because all 10 screws share the same format, the set supports organized parts storage and avoids mixing unmatched hardware into a differential assembly. The pack contents are stated plainly: 10 differential self-tapping screws. On the bench, this set fits naturally into routine servicing, replacement of lost fasteners, or preparation of spare hardware before a rebuild begins. It also works as a practical stock addition for model toolboxes and parts drawers, where a clearly defined 2x8 mm screw can save time during maintenance on compatible assemblies. Warning! Not suitable for children under 14 years.
Axes & drive shafts
37mm SwingShafts, RC spare part for XV-02
300051700€16.19
These 37 mm SwingShafts are a focused RC spare part for keeping compatible chassis setups running cleanly and consistently. Designed for the XV-02 chassis, they replace worn swing shafts in the assembly universal area, where accurate fit and free movement matter to drivetrain response and stable operation during repeated running sessions. Each shaft is marked A • 37 and the set supplies 2 matching parts for the same specified length. The black rod form with metal inserts at both ends reflects the compact mechanical role these parts play inside the chassis assembly. On TT-02 based cars, the shafts can also be used alongside Item 54623 and 51444 for defined compatibility. Combined with Item 54874, they also allow a wider camber angle adjustment range on the TT-02 chassis, opening more setup latitude for fine tuning suspension geometry. This kind of replacement suits regular workshop maintenance, rebuilds after heavy use, or planned setup changes between chassis configurations. In a tuning session, fresh shafts can restore precise movement in the relevant assembly area, while in a parts box they serve as a chassis-specific option for XV-02 and selected TT-02 builds.
Axes & drive shafts
39mm Drive Shaft Set, RC spare part for TT-01E
300050883€12.99
This RC spare part set provides 2 drive shafts in a 39 mm format for selected Tamiya chassis. Designed for TA-01, TA-04, TA-05 and TT-01E platforms, the shafts sit in the drivetrain where rotating assemblies need a compact link that can keep transmitting power while suspension parts move through their travel. Each shaft uses a straight center section with rounded ends and cross pins, a dogbone-style layout commonly used to connect outdrives and wheel-side drive components. That shape allows the shaft to articulate inside the drivetrain rather than acting as a fixed rod, which matters when a chassis is cornering, accelerating or running over uneven surfaces. The 39 mm dimension is the key fit point here, so matching the stated length is essential when replacing worn or missing drivetrain parts. Supplied as a 2-piece set, the pack suits paired servicing work without forcing a mixed left and right setup. In workshop use, these shafts fit naturally into rebuilds, maintenance sessions and parts-box planning for compatible touring car chassis. They also make sense as a trackside spare when a running session calls for a quick drivetrain refresh on TA-01, TA-04, TA-05 or TT-01E based models. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
3mm 5.5x5.0mm Spacer, model accessory, 10-pack
319804641€8.19
This spacer set is built around exact measurements that matter during model maintenance and parts replacement. Each piece is specified at 3 mm with 5.5 x 5.0 mm dimensions, giving a clear reference for assemblies that rely on this format to maintain the intended spacing between compatible components. The set contains 10 matching spacers, which supports repeated service work without mixing different sizes in the same build. The defined dimensions make this set useful when an existing assembly already calls for 3 mm spacers and when consistent fit across several mounting points is needed. Rather than relying on approximate sizing, the stated 5.5 x 5.0 mm format gives a direct basis for checking compatibility against the parts already in use. On the workbench, these spacers suit routine maintenance, measured replacement and keeping spare hardware ready for future adjustments. The 10-piece count also helps when several identical positions in one assembly need the same spacer size, or when matching replacements are kept in reserve for later servicing. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
3mm O-Ring black, model accessory, 10-piece
300084195€1.99
This 10-piece pack of black 3 mm O-rings adds a practical spare-parts supply for model maintenance, repair work and small mechanical assemblies. Each ring shares the same compact diameter and circular form, making the set useful wherever a matching seal or replacement ring is needed to restore fit between moving or joined parts. The pack contains 10 identical rubber O-rings, which helps keep replacements consistent across repeated service jobs instead of mixing unmatched sizes. Their black finish makes them easy to distinguish from other small workshop parts during sorting and storage. In model building and accessory upkeep, small sealing components often matter as much as larger visible parts, especially when a worn ring needs a direct like-for-like swap rather than an improvised substitute. Kept in a parts drawer, tool case or bench organiser, these O-rings are ready for routine maintenance sessions and quick repairs. The uniform 3 mm format also suits builders who prefer to keep duplicate consumable parts available before starting detailed assembly or servicing work. Warning! Not suitable for children under 14 years.
Screws & ball head screws
3mm Washer MA14, model accessory, 15-piece set
300050586€3.09
This MA14 washer set brings a straightforward supply of 15 matching 3 mm washers to the workbench, supporting model maintenance, replacement tasks and assembly jobs that call for correctly sized small hardware. The compact format suits builders who need a ready reserve for routine parts handling rather than a mixed assortment. Each washer is identified in the data as 3 mm Washer and grouped under Models Supplies, placing it clearly in the spare-parts and workshop-accessory side of model building. The 15-piece count gives a practical quantity for keeping common hardware on hand during repairs or when an existing build needs fresh fastening components. The MA14 reference helps distinguish this set from other small parts in a broader workshop stock, especially where several washer sizes may be stored together. On the bench, a dedicated washer pack like this supports cleaner preparation before assembly starts and quicker replacement when a small part is missing during maintenance. It also fits neatly into organised spares storage, where size-specific hardware can be sorted by reference and reached quickly for the next build session.
Other spare parts & accessories
3x0.7mm Aluminum Spacer Set, model accessory
309805645€6.29
These aluminum spacers in 3x0.7 mm format support accurate spacing in detailed model assembly, where a defined gap can influence fit, alignment and component position. The 10-piece pack gives a ready supply for workshop drawers, replacement needs or builds that use several matching spacers in one setup. The 3 mm size and 0.7 mm thickness make this set suited to fine adjustment work rather than broad structural filling. In model construction, spacers like these sit between mounted parts to create consistent separation and help maintain the intended position of screws, brackets or other fitted elements. Aluminum brings a clean, technical finish to this small but useful hardware format and fits naturally into precision-focused hobby work. Whether used during a fresh build, a repair or a measured setup change, the defined dimensions make selection straightforward when a specific spacing value is needed. Kept in a parts box or bench organizer, the set adds a practical option for builders who work through detailed fitting tasks one measured step at a time. Warning! Not suitable for children under 14 years.
Screws & ball head screws
3x10 Tapping Screw BK, model screw set, 10 pcs
309804392€6.19
This screw set supplies 10 black 3x10 tapping screws for model assembly, replacement work and workshop stock. The compact format suits builders who need the exact fastener type stated on a parts list or want matching hardware ready for routine maintenance on compatible models. The 3x10 specification gives a direct reference for size, which helps when sorting spare hardware for repairs or preparing parts before a build begins. The black finish supports a uniform appearance on visible fixing points where darker hardware is preferred. As tapping screws, these fasteners are intended for fastening duties in suitable model applications where this screw type is required. The pack count of 10 pieces provides a practical quantity for replacing missing screws, refreshing used fixings or keeping a small reserve in the workshop. On the bench, this set fits naturally into regular maintenance tasks such as securing parts after disassembly or replacing worn hardware during a rebuild. It also works well as a dedicated spare pack kept alongside model tools and sorted fasteners, ready when the correct 3x10 tapping screw is needed. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
3x10mm Alum. Turnbuckle Shaft, chassis accessory
300053892€11.99
These 3 x 10 mm aluminium turnbuckle shafts bring precise anti-roll bar adjustment to compatible chassis setups while adding a clear blue finish to the hardware. The set contains 4 shafts and is intended as a chassis accessory for fine tuning left and right anti-roll bar settings without removing the adjuster. The compact 3 x 10 mm dimensions suit dedicated on-road racing platforms where small setup changes matter. As a replacement for 9804250, this set gives a direct route to refreshing existing hardware with the same stated function. Compatibility is listed for TRF415MSX, TRF415MS, TB Evo. IV MS and TB Evo. IV. TA05 fitment is also specified, with the condition that adjusters must be shortened. At the workbench, these shafts support quick setup changes between runs when anti-roll bar balance needs a finer response. In regular maintenance, the 4-piece pack also helps keep a matching set ready for rebuilds, repairs or chassis-specific spares within a race box. Warning! Not suitable for children under 14 years.
Screws & ball head screws
3x12mm Counter Screw, model screw set, 10 pieces
300050581€3.29
This screw set provides 10 matching countersunk screws in a 3 x 12 mm format for model assembly, maintenance and hardware replacement. The flat countersunk head supports a flush finish on compatible parts, which helps keep surfaces even where protruding fasteners would interfere with fit or movement. The set is supplied as metal fastening hardware and suits tasks that call for the same stated size across several fixing points. A 12 mm length gives reach through compatible layered parts, while the 3 mm diameter defines the thread size for matching holes and receiving material. Because all 10 screws share the same format, the pack works well for replacing lost fasteners in groups rather than mixing different sizes during a repair. The pointed threaded shafts are shaped for fastening use, and the Phillips drive allows controlled tightening with a matching screwdriver. On the workbench, the set supports routine upkeep of model builds, spare-parts sorting and planned rebuilds where identical hardware is needed across several positions. It also fits neatly into parts storage for future service jobs, keeping a clearly specified screw size ready when a compatible assembly calls for 3 x 12 mm countersunk fixings. Warning! Not suitable for children under 14 years.
Screws & ball head screws
3x12mm Steel CS HexHead Screws, model accessory
300051631€2.79
These 3x12mm Steel CS HexHead Screws are a focused workshop accessory for maintaining compatible model and RC assemblies. The steel construction provides the specified material for replacement use, while the countersunk screw form is made to sit into matching recessed mounting points for a flush finish. Each screw uses a hex head, giving a defined tool interface for secure tightening during fitting and servicing. The pack contains 10 screws, which makes it useful for routine maintenance, repair work, or keeping matching fasteners ready in the parts box. The 3x12mm size is the key reference for checking compatibility with the intended assembly point, especially where the original build calls for the same thread and length. As replacement hardware, these screws are suited to restoring firm connections after wear, loss, or repeated disassembly during setup changes and repairs. On the workbench, they fit naturally into regular service tasks such as refreshing mounting points on a chassis, reattaching compatible sections, or replacing individual fasteners before the next run. For model builders who keep spare hardware sorted by size, this 10-piece set adds a clear, easy-to-store option for ongoing maintenance. Warning! Not suitable for children under 14 years.
Screws & ball head screws
3x15mm Tapping Screw, model accessory, 10-pack
300050583€3.39
This 10-pack of 3x15 mm tapping screws is a focused workshop spare for model maintenance, repairs and ongoing assembly needs. The exact 3x15 mm size gives a clear match point when worn, missing or damaged fasteners need to be replaced with the same format, and the TA-01 and TA-02 designation identifies the intended application directly in the part name. The set consists of 10 silver metal screws with a threaded shaft, rounded pan head and cross-head drive as shown in the product image. That head shape supports secure seating against the mounted part, while the cross-head recess allows controlled tightening with a suitable screwdriver. Keeping identical screws together in one pack helps maintain a consistent fit across the relevant fixing points instead of mixing different lengths or thread types during service work. On the bench, this kind of hardware is useful for routine chassis upkeep, replacing lost fasteners after disassembly, or keeping matching spares ready between rebuilds. For TA-01 and TA-02 based model work, the pack offers a straightforward way to restore the specified fixing point with the correct screw format.
Screws & ball head screws
3x22mm Screw Pin, model spare part, 4 pcs.
309805755€4.29
This spare-parts set provides 4 matching 3 x 22 mm screw pins for compatible model assemblies, giving a direct way to replace fastening parts that are missing, worn or no longer holding as intended. The defined 22 mm length and 3 mm format help maintain the original connection points in builds that rely on this pin size. Each piece has a long cylindrical shaft, a rounded tip, a wide head and a ringed section below the head. That shape supports guided insertion and a seated hold in the matching mounting point, while the uniform dimensions across all 4 pieces keep the set consistent for repair work. The black finish gives the parts a neutral technical appearance that blends into many model layouts and spare-parts boxes. This 4-piece pack suits routine workshop upkeep, targeted repairs and the replacement of individual fastening points on compatible models. Kept alongside other maintenance parts, the pins are ready when a build needs a like-for-like fixing part in the 3 x 22 mm size. Warning! Not suitable for children under 14 years.
Axes & drive shafts
3x23mm Turn-Buckle Shaft, RC spare part, 4 pcs
309805780€4.69
This set of 4 turn-buckle shafts in 3x23 mm format adds a precise replacement option for RC model maintenance and setup work. The metal shafts are threaded on both ends and use a compact central section that supports handling during installation, removal and adjustment inside a linkage assembly. Used in steering or similar connection points where exact length matters, turn-buckle shafts allow the assembly to be tuned by changing the effective linkage position rather than replacing the whole mechanism. The 3x23 mm specification is the key fit detail for matching an existing compatible build, and the pack of 4 provides a practical quantity for servicing paired linkage points or keeping matching spares on hand. The dark metallic finish and cleanly cut threads reflect the functional, workshop-focused character of the part. These shafts fit naturally into bench work such as replacing worn connectors, refreshing a running chassis or preparing a model for its next setup session. In a parts box, pit case or hobby drawer, a matched set of 4 helps keep compatible RC assemblies ready when a linkage needs a fast, like-for-like swap. Warning! Not suitable for children under 14 years.
Screws & ball head screws
3x5mm Flathead-Screw, model screw set, Phillips
300051211€2.89
This screw set supplies 5 matching 3 x 5 mm flathead fasteners for model building, maintenance and hardware replacement. The compact size and crosshead design make the screws easy to identify at the bench, while the flat head sits neatly against compatible parts for a clean, flush connection. Each screw has a Phillips-style drive and a short machine thread, as shown by the defined head shape and threaded shaft. That combination suits small fastening points where controlled tightening matters and where oversized hardware would interfere with surrounding parts. The set is useful when an original screw is lost during assembly, when worn hardware needs replacing, or when a matching group of fasteners is needed for a repair. The black finish keeps the hardware visually understated on many technical builds. On a workbench, these screws fit naturally into routine model care: securing a bracket, refitting a cover, or restoring a connection after disassembly. Kept alongside other spare hardware, the 5-piece pack provides a practical reserve for compatible model sections that call for the same 3 x 5 mm format. Warning! Not suitable for children under 14 years.
Screws & ball head screws
3x6mm Steel CS HexHead Screws, model hardware
300051625€2.89
These 3x6mm Steel CS HexHead Screws provide compact fastening hardware for model maintenance, repairs and fresh assembly work. The steel build pairs a countersunk head with a hex socket drive, so each screw can sit flush in a matching recess while allowing firm, controlled tool engagement during installation. In the pack are 10 matching screws, shown with a dark metal finish and short threaded shafts suited to precise mounting points. The 3x6mm size makes this hardware relevant wherever that exact thread and length are specified in a compatible model or accessory assembly. A countersunk head is used where the screw needs to settle into the surface rather than stand proud, which helps preserve clean part alignment around plates, brackets or other fitted sections. The hex socket format also reduces the chance of slipping compared with a simple slotted head when careful tightening is needed on small-scale assemblies. These screws fit naturally into routine workshop tasks such as replacing worn fasteners, securing parts after servicing, or keeping spare hardware on hand for future adjustments. On RC cars and other model builds, timely replacement of damaged mounting hardware helps maintain consistent fit at the fastening point and supports reliable running after repeated use. Warning! Not suitable for children under 14 years.
Screws & ball head screws
3x6mm Steel Hex Head Screws, model accessory
300051624€2.89
These 3x6 mm steel hex head screws are replacement fastening hardware for model maintenance, repair and parts changes. The steel construction and internal hex drive support secure tightening with a matching tool, while the compact size suits smaller mounting points where consistent hardware dimensions matter. Supplied as a set of 10, they provide a practical stock of matching screws for workshop drawers, pit boxes or spare-parts cases. The rounded head shape and fully threaded shaft are suited to refitting components that rely on small, uniform fasteners. When an original screw is worn, lost or damaged, replacing it with the same 3x6 mm format helps preserve the intended fit at the fixing point. The dark metal finish keeps the set visually consistent, and the identical sizing across all 10 pieces simplifies sorting and selection during repair work. On a workbench, these screws suit routine servicing, rebuilds and hardware replacement on model assemblies that call for this exact size. They are also useful to keep on hand as spare fastening hardware, ready for quick swaps when a repair should not be delayed by a missing screw. Warning! Not suitable for children under 14 years.
Screws & ball head screws
4 mm Adjuster M2, model accessory, 6-piece set
300050633€3.19
This 4 mm Adjuster M2 pack provides 6 matching ball pans for model maintenance, repair work and fresh assemblies that call for the same connection part throughout a linkage setup. The compact shape and M2 specification make the set a practical choice when worn or missing joint pieces need to be replaced with matching components. Each ball pan is supplied as a separate small part, so the pack can support several connection points in one project or stay on hand as workshop spares for later servicing. The 4 mm dimension gives a direct reference when matching existing hardware, while the uniform off-white moulded finish helps keep the parts easy to identify among other small model components. Scope of delivery: 6 ball pans. This set suits bench repairs, routine parts replacement and planned builds where identical linkage fittings are required across the assembly. It also works well as a stock spare for model toolboxes and hobby drawers, ready for the moment a control connection or adjuster point needs the same M2 and 4 mm format again. Warning! Not suitable for children under 14 years.
Screws & ball head screws
4 mm Serrated Wheel Nuts, model accessory, steel
300042282€4.19
These 4 mm serrated wheel nuts are made for compatible 1:10 models and bring a clean, functional solution to wheel mounting and replacement work. The steel construction gives each nut the solid threaded form needed for repeated fitting, while the serrated base increases contact at the mounting point when tightened. In the workshop or at the track, that combination supports a firm connection between wheel and axle hardware. The set contains 8 wheel nuts, making it useful for complete wheel swaps as well as keeping matching spares ready for service intervals. The compact format suits routine maintenance jobs where lost or worn fasteners need to be replaced with the correct size. The metallic finish and flanged nut shape match the hardware style commonly used on model vehicle wheel hubs, and the threaded interior is designed for direct fastening rather than decorative use. As a dedicated accessory part, this set focuses on one specific task: securing wheel assemblies with the correct 4 mm steel nut. On a repair bench, the 8-piece count supports organized replacement across multiple corners of a chassis. During rebuilds or setup changes on compatible 1:10 models, the serrated contact face helps the nut seat with a more positive mechanical hold as the wheel is fitted and tightened. Warning! Not suitable for children under 14 years.
Axes & drive shafts
44mm TRF L.F. Drive Shafts, RC spare part
300042362€22.49
These 44 mm TRF L.F. drive shafts are built for double cardan joint drivetrains that use swing shaft caps from Item 54921. The steel construction and fluorine surface coating focus on two key demands in RC driveline tuning: controlled movement at the joint and reduced friction where the shaft is working under load. Supplied as 2 matching shafts, the set supports a balanced left and right installation in compatible chassis layouts. A key update is the 10.8 mm needle pin section, which is 1 mm longer than on previous shafts. That extra length is specified to get more from swing shaft cap option parts, making these shafts a targeted upgrade for builders refining a double cardan setup rather than changing unrelated areas of the car. The LF44 marking shown on the shafts helps identify the part during maintenance or when several driveline options are kept in a pit box. In workshop use, these shafts suit rebuilds after wear, planned driveline updates, or a fresh parts selection for a compatible competition chassis. They are best matched with the stated cap system, where the longer pin section and low-friction coating can be used as intended in the assembled transmission layout.
Axes & drive shafts
45mm Drive Shafts, TRF421 spare part set
300042387€18.99
These 45 mm drive shafts for TRF421 are a focused drivetrain spare for model car maintenance, supplied as 2 matching parts for Low Friction Double Cardan Joint Shafts. The dark metal shafts are marked LF45 and use a straight shaft form with joint ends shaped for the matching assembly. At the shaft end, each part uses a 10.8 mm needle pin. This detail is specified to work together with Item 54921 Reinforced Swing Shaft Caps, with 2 pieces each for front and rear fitment. The compatibility note is narrow by design: these shafts are only for cars that use Item 54921, which keeps the replacement choice tied to the correct drivetrain layout instead of a broad universal fit claim. As a spare part set, the pair supports maintenance after wear in the transmission area and restores the intended shaft length of 45 mm on both sides. The 2-piece format suits workshop stock, scheduled rebuilds and targeted repairs on a TRF421 setup. In a bench session, the matched pair helps keep the drivetrain specification consistent when replacing both corresponding shafts in the same assembly. Warning! Not suitable for children under 14 years.
Axes & drive shafts
46 mm TRF Swing Shafts, RC accessory, aluminium
300051760€18.99
These TRF 46 mm aluminium half cardan shafts add a focused drivetrain upgrade for compatible RC chassis, combining low weight with a ball bearing mounted layout that helps the axle rotate with less friction. In running, that reduced drag supports steadier power delivery through direction changes, where speed loss at the shaft can affect how cleanly a car carries momentum. The set contains 2 lightweight 46 mm swing axles and is intended as a chassis-specific accessory rather than a universal fit part. The half cardan design suits drivetrain maintenance, replacement work and targeted tuning where the shaft assembly is a key wear point. For TRF421X use, the specification names compatibility with ball bearing set 51762 and differential joints 51764 when the shafts are installed on the TRF421 chassis 42384. That combination gives a clear reference for planning a matching drivetrain setup instead of mixing unspecified parts. On the bench, the defined 46 mm length helps identify the correct shaft format before installation. During track use, the ball bearing mounted construction supports smoother axle movement in repeated corner entries and exits, where friction control matters most in a responsive RC drivetrain. Warning! Not suitable for children under 14 years.
Screws & ball head screws
4mm Ball Connector M2, model accessory, 5-piece
300050590€3.99
This 5-piece set of 4 mm Ball Connector M2 hardware adds a compact connection point to model mechanisms that rely on precise moving links. Each connector uses a polished spherical head above a short neck, hex section and threaded post, creating a clear interface for compatible snap-on or pivoting parts in tight installation spaces. The 4 mm head size and M2 thread make these connectors suited to small-scale mechanical layouts where clean movement and accurate mounting matter. The metal construction gives each piece a defined shape for repeated fastening and removal during setup, adjustment or replacement work. The hex base supports tool-assisted tightening, while the threaded post seats into matching mounting points for a secure mechanical hold. With 5 identical connectors in the pack, the set can equip several linkage positions in one assembly or replace worn hardware across existing running gear. On the workbench, these connectors fit naturally into repair, tuning and fresh build tasks where steering links, control rods or other articulated parts need a ball-end mounting point. The consistent dimensions across all 5 pieces help keep left and right connection points matched when a model uses mirrored hardware. Warning! Not suitable for children under 14 years.
Screws & ball head screws
4mm Flange Lock Nut Bla (8), RC accessory set
300054642€3.89
This RC hardware set brings a clean wheel finish and a more secure fastening point to compatible model cars. Each 4 mm flange lock nut uses a nylon insert that grips the thread as the nut is tightened, helping the connection stay in place when the chassis is exposed to repeated vibration, direction changes and regular wheel removal. The set contains 8 blue flange lock nuts, shown as individual metal fasteners with a flanged base and visible locking ring. That flange gives the nut a broader contact surface than a plain hex nut, which helps distribute clamping force at the mounting point. The blue colour variation also changes the look of the wheel area, making it useful for refresh work on existing builds or for replacing standard hardware supplied in many RC kits. The parts are intended as accessory or spare hardware rather than a complete vehicle component group. Compatibility covers a range of touring car and off-road cars, making the set useful for workshop drawers, rebuild projects and routine running maintenance. When wheel hardware has been removed repeatedly or no longer matches the rest of the chassis, this 8-piece set provides a straightforward replacement option with a locking function built into each nut.
Screws & ball head screws
4mm Flange Lock Nut Blue, RC accessory, 5-pack
300053159€13.79
These 4 mm flanged lock nuts bring a functional hardware upgrade to compatible RC vehicle setups, combining blue anodized aluminum with a compact fastening format that trims weight and sharpens the look of exposed wheel hardware. The metallic finish stands out clearly against darker rims, suspension parts and chassis details, giving maintenance work and final setup a more technical appearance. Each nut uses a hexagonal body with a threaded center hole and a wide integrated flange. That flange increases the contact area at the mounting point, which helps distribute pressure more evenly across the wheel surface than a narrow nut alone. The lock-nut format is suited to repeated fitting and removal during tuning, cleaning and routine parts changes. With 5 matching pieces in the pack, one extra nut remains available after a standard 4-wheel installation, which is useful to keep with trackside spares or workshop hardware. The small size and clear 4 mm specification make this set easy to match with compatible wheel axles and hubs in RC maintenance or customisation work. Whether replacing worn hardware, refining the finish of a competition-inspired build or keeping a spare ready between running sessions, these aluminum nuts add a precise mechanical detail where it is seen most.
Screws & ball head screws
4mm Shift Ball Connector M3, model spare part
319804831€4.29
This 4 mm Shift Ball Connector with M3 thread is a dedicated spare part for Truck and HiLift model applications. The stated size and thread specification provide a direct reference for replacing the same connector type in an existing assembly, where the correct fit of small linkage hardware matters to the overall mechanism. Its role is focused and practical: restoring a worn, missing, or damaged connection point with the specified 4 mm ball format and M3 threading. Because the product data identifies Truck and HiLift compatibility, the connector is suited to those model ranges rather than to general, undefined use. That makes it a useful workshop part for routine maintenance, repair work, and keeping compatible builds equipped with the correct hardware standard. The compact format also stores easily alongside other model service parts, so the required connector type is ready when a rebuild or replacement is due. In a repair session, this spare part can be selected by its exact connector size and thread rather than by guesswork. For ongoing model upkeep, it supports a tidy stock of application-specific hardware for Truck and HiLift assemblies. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
4mm Shim Set, RC accessory, 0.1/0.2/0.3 mm
300053586€11.29
This 4 mm shim set brings fine mechanical adjustment to RC maintenance and model workshop tasks where shaft spacing needs a precise correction. The pack contains 30 shims in total, divided into 10 pieces each at 0.1 mm, 0.2 mm and 0.3 mm, so clearance can be tuned in small measured steps instead of forcing a single thickness into every job. Each shim fits 4 mm shafts and is intended for situations where more clearance is required. The thin ring format slips onto the shaft to change spacing directly at the point of assembly, which helps when rotating parts need a more exact position. Combining different thicknesses from the set also allows intermediate spacing values, giving more control during drivetrain setup, axle work or other moving assemblies that rely on accurate alignment. On the bench, the 3 thickness options support methodical trial fitting during maintenance, rebuilds or parts replacement. The grouped sizes make it straightforward to compare spacing changes, correct excess play and refine the fit of compatible components without replacing the shaft itself.
Screws & ball head screws
4x10mm Step Screw, spare screw set for M-Chassis
300050585€4.39
This spare screw set provides 5 matching 4x10 mm step screws for compatible model chassis work, with a compact format that suits replacement, maintenance and rebuild tasks. The stepped design combines a threaded section, a cylindrical shoulder and a domed head, so one fastener can secure a part while also maintaining the spacing that a plain screw may not provide. The data names TA02, TA03 and M-Chassis compatibility, giving a direct reference for parts matching during service work. In a workshop tray or spares box, the 4x10 mm size is easy to identify when a build calls for the same specification. The 5-piece quantity supports targeted replacement rather than forcing a full hardware change across a chassis. The metal construction fits the role of a small mechanical fastening part where repeated fitting and removal are part of normal model upkeep. This screw pack suits bench repairs, scheduled maintenance and the final stages of a rebuild when the correct shoulder screw is needed to complete a mounting point. It also works as a useful reserve for keeping compatible TA02, TA03 or M-Chassis models ready for the next running session.
Screws & ball head screws
5mm Adjuster Short, RC spare part set, 8 pieces
300054489€2.89
This spare part set brings 8 short 5 mm adjusters into the suspension area of an R/C car, where low-friction material helps linked joints move with a smoother action. Each piece is shaped for use at connection points that need a pivoting link, making it a practical choice for maintenance, worn-part replacement or a fresh chassis build that calls for matching hardware. The short format suits tighter installation points than a longer adjuster and keeps the linkage layout compact around the joint. In use, the circular eyelet opening forms the attachment point for the connected rod or pin, while the low-friction composition focuses on reducing drag at the moving interface. That can help suspension parts articulate more freely as the chassis loads and unloads through direction changes, uneven surfaces and repeated laps. The set contains 8 identical adjusters, which supports consistent fit across several matching positions on a compatible R/C car. On a workbench, these adjusters fit naturally into routine rebuilds, suspension refreshes and setup corrections where several joints need the same part at once. During running sessions, smoother linkage movement can support cleaner suspension response as the car transitions through braking, turn-in and acceleration.
Screws & ball head screws
5mm Adjuster, model accessory, 19mm length
300050596€3.49
This model accessory set supplies 6 ball pans sized at 5 mm diameter and 19 mm length for compatible maintenance and replacement work. The specified dimensions make the set easy to match against an existing assembly, especially when a worn or missing fitting needs the same connection size and overall length. The pack is intended for use with 50592, which gives a direct compatibility reference instead of leaving the fit to estimation. Ball pans sit at the connection point of linked parts, so the stated 5 mm diameter matters when selecting the correct hardware for a rebuild or service task. The quantity of 6 supports repeated replacement work across the same assembly and leaves matching spares available for later upkeep. On the workbench, this set fits neatly into routine model maintenance, whether a compatible build is being refreshed after use or a stored chassis is being brought back into running condition. The compact hardware format also makes it practical to keep alongside other small fittings for planned repairs and parts organisation. Warning! Not suitable for children under 14 years.
Screws & ball head screws
5mm Ball Connector Nut, model accessory, 4pcs
309804206€5.49
The 5mm Ball Connector Nut set supplies 4 matching threaded fittings for model assembly, repair and maintenance work. Each piece combines an internal screw thread with a hexagonal base, giving small mechanical connections a defined contact point for tightening and adjustment during a build. The compact black metal parts are shaped for clean integration into technical assemblies where consistent hardware matters. Their uniform form keeps all 4 fittings visually and mechanically aligned across the same application, which helps when replacing worn connector nuts or preparing matching hardware for a fresh setup. The 5 mm sizing gives a clear reference for compatibility within the intended assembly, while the threaded interior supports a direct fit onto the corresponding shaft or screw. On the workbench, these fittings suit routine servicing, parts replacement and detail-focused model projects that call for precise small hardware rather than mixed spare nuts. The 4-piece pack also leaves matching components ready for follow-up maintenance when the same connection point appears more than once in an assembly. Warning! Not suitable for children under 14 years.
Screws & ball head screws
5mm Ball Head M3, model accessory, 10-piece set
300050592€6.79
This 10-piece set of 5 mm Ball Head M3 parts adds a precise connection component to model maintenance, repair and assembly work. Each ball head uses an M3 threaded shaft and a 5 mm ball, a combination that suits compatible linkage and mounting points where a compact pivoting connection is needed. The metal construction and hex shoulder shown on each part support secure tightening during installation. The pack includes 10 matching ball heads, which helps keep spare hardware on hand for repeated service jobs or fresh builds that call for the same fitting throughout. The spherical head shape is suited to moving connection points that need controlled articulation rather than a fixed joint. The short threaded section keeps the mounting format specific and easy to match against existing compatible parts. The gold-coloured finish shown in the set also makes each piece easy to identify in a parts tray or workshop drawer. On a repair bench, these fittings suit the replacement of worn connection points on compatible models. During a new build, the matching 10-piece quantity supports consistent hardware selection across multiple mounting positions and leaves reserve parts available for later maintenance. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
5mm Body O-Rings, model accessory, 10 pieces
300054384€3.09
These 5 mm body O-rings are small model accessory parts that make a visible difference at the body mounts. Fitted to body mount rods, they allow fine height adjustment of the bodyshell position, so the shell can sit with a more controlled fit on the chassis during setup. The set contains 10 O-rings for replacement stock or fresh installation on compatible body posts. Their role is not limited to spacing: each ring also provides a cushioning effect between the bodyshell and the mount point. On rougher driving surfaces, that added cushion helps reduce body chatter that can appear when the shell moves against the posts over bumps. This gives the shell mount a tidier, more settled feel while the model is running. In workshop use, the rings are easy to keep on hand for routine maintenance, rebuilds, or shell changes between different bodyshell setups. They suit drivers who fine-tune shell height on body mount rods and want spare mounting hardware ready for regular track or car park sessions. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
5mm Shim Set, RC accessory, 0.1 0.2 0.3mm
300053587€11.29
This 5 mm shim set brings precise spacing control to RC chassis work, with 3 thicknesses at 0.1 mm, 0.2 mm and 0.3 mm for fine mechanical adjustment. Used at 5 mm fitment points, the shims help take up excess movement where a cleaner, tighter setup is needed around suspension parts or wheel axles. The set includes 30 shims in total, arranged as 10 pieces of each thickness, which supports repeated setup changes without relying on a single size. Small spacing differences can change how parts sit against each other, and these thin rings make those corrections measurable rather than improvised. On a maintenance bench, they can be selected to match the amount of free play present at a given point. On a fresh build, they support more exact placement of moving parts before the chassis goes into use. The shim assortment suits both on-road and off-road Tamiya vehicles, so the same pack can serve different running platforms in one workshop. Whether the goal is tidying axle movement, refining suspension fit or keeping a race chassis more closely adjusted, the 5 mm format gives a compact tuning part that earns its place in a spares box.
Screws & ball head screws
5mm/M3 Ball Socket Set, model accessory, 8 pieces
300050875€5.99
This 5 mm/M3 ball socket set brings a straightforward replacement option for compatible model linkages, with 8 matching parts ready for maintenance, repair work or a fresh build. The rod-end style shape and circular socket opening suit connection points that rely on a compact joint with controlled movement. Each piece is formed as a small connector end with a faceted outer body, a cylindrical shaft and a socket head that pairs with the stated 5 mm/M3 specification. That combination helps when an existing setup needs the same dimension rather than a close substitute. The pack format keeps several identical parts on hand at once, which is useful when multiple joints on one chassis use the same fitting or when spare hardware belongs in a regular bench stock. The black finish keeps the set visually consistent with many technical assemblies without drawing attention away from the surrounding components. In workshop use, the set fits naturally into routine servicing after wear at steering or suspension connection points. It also suits rebuilds where matching linkage ends across several rods help keep the assembly consistent and easy to sort during installation. Warning! Not suitable for children under 14 years.
Screws & ball head screws
5x9mm Ball Connector, model accessory, 5 pcs.
309805611€7.89
These 5x9 mm ball connectors add a compact mechanical link point to RC and model assemblies where a threaded joint and a smooth pivot surface need to work together. Each piece combines a 5 mm ball, an M3 threaded shaft and a 9 mm length, creating a clear fit for linkage tasks that depend on accurate spacing and dependable attachment. The polished metal finish and defined ball shape suit moving connections such as steering rods, suspension joints or other articulated model hardware, while the hexagonal shoulder provides a practical grip area during fitting. With 5 matching connectors in the pack, the set supports fresh builds, maintenance work and the replacement of worn fastening points. The small format also makes these parts useful for keeping workshop drawers or field boxes stocked with commonly needed RC hardware. In a chassis rebuild, the connectors can be fitted where rods or jointed parts need a threaded anchor and a pivoting contact point. On the bench, the uniform dimensions help keep left and right linkage positions consistent when several matching connection points are required in the same assembly. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
6 mm Shim Set, model accessory, 0.1 0.2 0.3 mm
300053726€16.29
This 6 mm shim set brings precise spacing control to model assemblies that need a cleaner fit on 6 mm shafts. With 3 thicknesses at 0.1 mm, 0.2 mm and 0.3 mm, the set supports small corrections where mechanical play affects alignment, rotation or part position. The set contains 30 pieces in total, arranged as 10 shims of each thickness. That spread makes it possible to compare different spacer combinations during a build or while servicing an existing model, instead of working around a single dimension. The thin shim format suits jobs where only a fraction of a millimetre is needed to correct end float or reduce unwanted movement between parts. Used singly or in combination, the spacers help adapt the fit to the exact requirement of the assembly point. On the bench, the set suits gearbox work, axle spacing and other 6 mm shaft applications where measured adjustment matters. As a compact workshop supply for model maintenance, repair or fresh assembly, it adds a practical range of fine spacer sizes that can be kept ready for repeated mechanical setup tasks. Warning! Not suitable for children under 14 years.
Axes & drive shafts
A-Parts Axlehousing CC-01, spare parts set
300005519€22.79
A-Parts Axlehousing CC-01 is a spare parts set for the CC-01 platform and is listed as parts for 58132. The black injection-molded runner carries several unused structural components in one frame, including axle housing style sections and mounting pieces that support a clean replacement job when original parts need to be swapped. The molded layout keeps each piece attached until removal, which helps with identification before assembly and reduces mix-ups between similar shapes. The visible parts include long housing sections, bracketed elements and a larger case-like component, all formed with mounting holes and connection points that suit chassis or drivetrain installation. Because the pieces come as a matched set on one sprue, builders can replace damaged sections with components produced together rather than mixing unrelated leftovers from a parts box. This kind of spare set fits naturally into bench maintenance, rebuild work and parts sorting between running sessions. When a CC-01 chassis needs fresh housing components after wear or breakage, the set provides the specific molded forms needed to return the assembly to working order.
Other spare parts & accessories
A-Parts Gearbox F/R 58370, RC spare parts
300004432€14.29
This A-Parts sprue is made for the 58370 and provides black injection-molded components for the gearbox F/R area of the DF-03. The unassembled runner groups housing halves, covers and structural sections in one set, giving repair work a direct route back to the intended drivetrain layout. The molded pieces show reinforced ribs, screw holes and cylindrical shaft or bearing mounts that matter when a transmission case needs its original geometry. A larger frame-like section with elongated slots adds another chassis-facing support element, while rounded shell parts serve as protective case sections around moving drivetrain parts. Because the components are supplied on the sprue, each shape stays clearly separated until preparation begins, which helps with part checking before installation. The glossy black finish matches the technical look of many RC chassis internals. This spare parts set suits maintenance benches, rebuild projects and targeted gearbox repairs where damaged housings, brackets or covers need replacement with matching forms. It also supports keeping a DF-03 running with dedicated structural parts on hand for future service work.
Other spare parts & accessories
Alligator Clip for P. Stand, model tool set
300074528€5.99
These alligator clips add a simple, controlled way to hold small model parts while cement or paint dries. The spring-loaded hinge and serrated jaws grip components firmly, so freshly finished pieces can stay separated from the work surface and remain easier to handle during careful bench work. Each pack contains 4 matching clips, which supports parallel work on several parts in the same session. The oval wire loop at the end of each clip provides a clear connection point for mounting on a compatible stand. The clips are intended for use with the Painting Stand, Work Stand and Bottled Paint Stand named in the product data, making them a practical addition for painting, gluing and drying steps where direct hand contact can disturb a finish. On a model bench, the clips can hold newly cemented sections while joints set, or keep painted components raised and separated between coats. Their compact metal form suits detail-focused tasks where small parts need a temporary grip point and a cleaner path through finishing work.
Shock absorbers & springs
Alum. Damper Retainer -1mm, RC part, blue anod
300053876€27.99
The Alum. Damper Retainer -1mm is a suspension tuning part for compatible RC chassis, combining machined aluminum construction with a blue anodized finish and a precise fit around the damper spring area. By lowering the spring set position by 1 mm compared with the aluminum mount of the OP595TRF shock, it supports a lower vehicle height and a more exact starting point for chassis setup. This set contains 4 spring plates for matched installation across the suspension. The rigid aluminum holder is made for reliable initial adjustment of the damper spring, helping setup changes translate more directly at the shock. Compatibility extends beyond the main chassis list: on TD4 and TD2 chassis, only standard front dampers can be installed. On MF-01X chassis, use with 42102 or 42273 or 42354 or 42355 or 54000. On F104 and F104W chassis, use with 53901. In workshop use, the 1 mm change gives a concrete option when refining stance and spring preload on touring, formula, or off-road based builds that share these chassis families. The 4-piece set suits rebuilds, replacement work, or a fresh suspension setup where consistent hardware across the dampers matters. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Alum. Turnbuckle Wrench blue, model tool, 3.0 mm
300053602€14.99
The Alum. Turnbuckle Wrench blue is a dedicated model tool for fine setup work on vehicles with 3 mm adjustable tie rods or camber rods. Its 3.0 mm clamping axle format is made to engage the turnbuckle directly, so alignment changes can be made with a controlled hand movement at the workbench between runs or during a full chassis service. The blue aluminum handle combines low weight with a firm feel, and the ribbed cylindrical shape supports stable finger placement while small adjustments are made. A forked open-end tip slides around the rod section to apply leverage where a standard wrench would be too bulky. This focused shape suits RC maintenance jobs where steering links and camber rods sit close to surrounding parts. The scope of delivery contains 1 clamping axle wrench. On a tuning bench, in a pit box, or beside a partly stripped chassis, this tool supports repeatable suspension and steering setup work without taking extra space. It also works well as a dedicated addition to a model building tool roll where 3 mm linkage hardware is adjusted regularly. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
Aluminium Shock Absorbers, 55.62 mm, 2-Piece Set
300053155€51.99
These aluminium shock absorbers bring a low-friction damper setup to compatible Tamiya M chassis models, combining a machined cylinder interior with a 55.62 mm overall assembled length. The metal damper design is intended for smooth operation, giving the suspension a more even response as the shafts move through the cylinder. Compatibility covers the M-06 chassis, M-06 PRO chassis, M-05 ver.II PRO chassis, M-05 chassis and M-05 PRO chassis. The set contains 2 shock absorbers and is supplied with 48 pieces for assembly, including the hardware and sealing parts needed for the damper build. Aluminium bodies, coil springs, shafts, rod ends, clips and rings form a detailed suspension set that suits replacement, rebuilding or chassis tuning work on the listed platforms. Mounted on a compatible M chassis, the dampers support controlled suspension movement during cornering, braking and direction changes. The purple finish gives the underbody a distinctive technical look, while the complete 2-piece configuration fits neatly into workshop sessions focused on maintenance, setup changes or restoring smooth damper action. Warning! Not suitable for children under 14 years.
Spare parts for old cars
Aluminum 4mm Lock Nut Set, model accessory, pink
319804624€7.19
This set of 4 aluminum lock nuts brings a precise fastening detail to model builds and maintenance work, while the pink anodized finish adds a bright visual accent at the wheel area. With a 4 mm size, the nuts suit compatible threaded axles where compact hardware needs to stay easy to handle during setup and part changes. The lock nut design is made for fastening tasks where vibration and repeated removal matter, making the set useful for routine servicing as well as colour-coordinated upgrades. Aluminum gives each nut a light metal construction that fits neatly into performance-focused builds without adding bulky hardware. The pink finish is more than a colour note on the parts tray: it helps distinguish this set quickly from standard silver or black fittings during bench work. Supplied as 4 matching pieces, the set covers one complete wheel mounting point on many model layouts. On the workbench, these nuts fit naturally into rebuilds, wheel swaps and detail updates where small hardware shapes the final look as much as the mechanical fit. They also suit spare-parts storage for regular running sessions, keeping a matching set ready when worn or misplaced fasteners need replacement.
Other spare parts & accessories
Antenna for 56019, model accessory, 175 mm
305365011€4.49
This antenna for 56019 is a dedicated model accessory with a stated length of 175 mm, intended for use where the matching reference calls for this exact part. The slim rod format gives the model a clean, defined finishing detail while keeping the replacement focused on the named application rather than a generic spare. The part is supplied as 1 piece and is described simply as an antenna for 56019, which keeps selection clear when a specific replacement is needed. The visible form shows a long metal rod with shaped ends, including a hooked bend at one end and a coiled section at the other, indicating a functional mounting or connection point within the matching model setup. That concrete shape matters when replacing a missing or bent antenna, because the end form can be just as important as the overall length. Used on the correct model, this 175 mm antenna suits repair work, parts replacement, or the completion of an existing build that needs the specified external component. It fits naturally into workshop tasks such as restoring a stored model, replacing a worn original, or finishing a project with the named 56019 reference in mind. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Antenna Pipe 300mm, model accessory, black
306095010€0.79
This black antenna pipe adds a neat, functional finishing detail to compatible RC model setups. With a length of 300 mm or 30 cm, the tube gives the antenna a defined route and helps maintain a clean layout above the body where a loose wire would look untidy. The straight tube form makes it useful as a replacement part in routine maintenance, after repairs, or when refreshing an older build with worn running hardware. Its single-purpose design keeps the fit straightforward: the pipe sits in the model's antenna mount and supports the aerial in an upright position. The black finish keeps the look understated, which suits a wide range of body colours and chassis layouts without drawing attention away from the model itself. In workshop use, a spare antenna pipe is a practical part to keep alongside other RC maintenance essentials, especially for builds that still use a visible aerial tube. It also suits restorations where small external details help return a model to a complete, ready-to-run appearance. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Antenna Pipe 380mm, model accessory, clear
306095001€0.89
This clear antenna pipe is a straightforward model accessory for RC setups that use an external aerial guide. With a length of 380 mm, it provides a long tube that can be fitted and trimmed to match the required antenna height on the model, keeping the wire routed in a visible, upright position above the bodyshell. The transparent finish leaves paintwork, markings and body lines unobstructed, which helps preserve the look of the completed model while still making the antenna route easy to follow during fitting. Supplied as 1 piece, it works well as a direct replacement for a damaged tube or as a spare kept on hand for workshop use. The simple tube format also makes it useful across routine maintenance tasks where a clean, correctly sized aerial guide is needed. On the bench, the 380 mm length gives enough material for model-specific adjustment before final installation. During transport, storage and running sessions, the fitted tube helps keep the antenna wire guided consistently instead of leaving it loose around the shell area. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Anti-Wear Grease 3g, model lubricant tube
300053439€12.991 kg = €4,330.00
Anti-Wear Grease in a 3 g tube supports smooth maintenance work on model drivetrains by combining high viscosity with precise placement. On differential gears, shafts and drive axles, the grease adheres well to rotating parts, so lubrication stays where the mechanism needs it during repeated movement. The formulation is described for model vehicles and is supplied in a compact tube with a fine, narrow nozzle for controlled dosing on small contact points. That narrow outlet helps place a small amount directly onto gear teeth, axle sections or shaft ends instead of coating surrounding areas. The grease is temperature stable and retains its viscosity over a wide temperature range, which helps keep application characteristics consistent as moving parts warm up in use. The supplied quantity is 3 g, making it suited to targeted servicing rather than bulk workshop filling. In regular upkeep, the tube fits neatly into a field box or bench drawer and is ready for quick drivetrain attention between runs. It suits focused lubrication tasks on compact assemblies where accurate placement matters, especially around differentials and other enclosed rotating components. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
Axle Spring (2) 58416, model spare part
309805304€0.89
Axle Spring (2) 58416 is a model spare part for the axle area, supplied as a 2-piece spring set under the stated 58416 designation. The format suits maintenance tasks where a matching replacement is needed for a worn, missing or no longer usable spring in a compatible model assembly. The focus here is clear part identification rather than broad fit claims. The ShortDescription names the component as an axle spring, and the pack count confirms 2 springs in the set. That makes the set useful for organised parts storage, planned servicing and direct replacement work where the correct designation matters. In a workshop drawer or spares case, the numbered reference helps separate this spring set from gears, shafts, screws and other maintenance components. During repair or upkeep, a dedicated replacement spring set can help return the axle section to its intended mechanical role in the assembly. The compact 2-piece format also suits keeping a matched pair on hand for future service jobs on compatible model builds. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Axle Spring (2), spare part for model chassis
309808008€2.99
This set of 2 axle springs is a dedicated spare part for 58347 and is shaped for mechanical return action at the axle assembly. Each spring is formed from silver-coloured metal wire and uses a tightly wound coil with one short straight leg, one longer angled arm and a small loop at the end, making the part easy to identify during maintenance. The geometry shown in the part itself matters: the coiled section stores torsion, while the two arms transfer that force back into the moving mechanism. That makes these springs suitable for restoring rotational resistance, return tension or repositioning in the intended axle location on a compatible model. Supplied as a matching pair, the set supports like-for-like replacement where both sides of an assembly use the same spring form. For workshop use, the clear standalone shape helps with part checking before fitting and with replacing worn, bent or missing hardware in an existing chassis setup. As a model spare part rather than a general hardware spring, it is best used where the 58347 fitment and the pictured form match the original assembly requirement. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
B-Parts Gearbox Super Clod Buster spare parts
300005294€19.49
B-Parts Gearbox Super Clod Buster 58321 is a replacement sprue for model maintenance and repair, bringing key transmission-area components together in one clearly structured set. The black injection-moulded frame presents the parts in their original grouped layout, which helps with visual checking before each piece is removed and installed. The sprue shows 2 large matching housing halves, a rounded cover plate, 2 circular discs with evenly spaced holes, a larger curved cover piece, and several smaller link arms and connectors. One housing half features an integrated cylindrical section, indicating a dedicated enclosure area within the gearbox assembly. The opposite half carries reinforcing ribs and multiple screw points, giving the rebuilt section the same shaped mounting structure as the original part set. Small moulded part numbers are also visible on the frame, which supports part recognition during a careful rebuild. This spare-parts set suits workshop use when a Super Clod Buster gearbox section needs replacement after wear, damage or a detailed restoration. It also helps keep a rebuild consistent by supplying matching moulded pieces from the same B-Parts group rather than mixing unrelated components.
Spare parts for old cars
Ball Bearing Set Hornet Grasshopper Chassis
300054997€17.19
This ball bearing set brings together 10 replacement bearings for a focused chassis service job across several classic Tamiya platforms. The pack contains 9 x 1150 ball bearings and 1 x 850 ball bearing, matching the sizes stated for the supported models and giving a clear route to replacing worn rotating parts with the correct mix. The set is intended for Hornet, Grasshopper, Grasshopper II, Super Storm Dragon, CW-01 chassis models such as Lunch Box, plus Mad Bull, Mad Fighter and Rising Fighter. Ball bearings sit at rotating points where shafts and axles need controlled movement, so the correct size matters as much as the quantity. The metal construction and ring design suit maintenance work on running gear and transmission areas where smooth rotation is needed. As a dedicated bearing pack rather than a mixed hardware assortment, it keeps the service task focused on the exact bearing types named in the data. It suits routine rebuilds, repairs after extended running, or planned upgrades on compatible chassis already on the bench. Kept in a workshop drawer or parts case, the 10-piece mix gives a ready reference for several well-known buggy and CW-01 based models when replacement bearings are due.
Other spare parts & accessories
Ball Differential Grease 10g, RC lubricant
300053042€11.39
Ball Differential Grease 10g is a dedicated lubricant for ball type differential gearing in RC model vehicles, supplied in a compact tube with an applicator nozzle for controlled placement on small drivetrain parts. The 10 g fill gives a practical amount for routine servicing, whether the differential is being refreshed during a rebuild or maintained between running sessions. The grease is specified for differential use rather than general-purpose lubrication, which keeps the copy focused on the part it is made for. The supplied tube format helps direct the grease into tight mechanical areas where ball differential components need careful coverage. Compatibility notes in the data reference a wide range of chassis families when used with the stated related parts, including XV-01, XV-01T, XV-01 PRO, M-07 CONCEPT, M-08 CONCEPT, TA06, TA06 PRO, TA06 MS, TT-02, TT-02D, TT-01 TYPE-E, TT-01D TYPE-E, TT-02RR, TT-02FT, TT-02B, MF-01X, M-05, M-05 PRO, M-05 ver.II PRO, M-06, M-06 PRO, DT-02, DT-03 and DT-03T. On the bench, the narrow nozzle supports precise application during drivetrain maintenance, helping keep grease where the ball differential needs it instead of spreading it across surrounding parts. In workshop use, the small tube stores easily with other RC service supplies and is ready when a ball diff setup is due for fresh lubricant. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Basic File Set Smooth Dbl. Cut(3), hobby file set
300074104€8.29
The Basic File Set Smooth Dbl. Cut(3) brings 3 distinct file shapes into one compact bench set for shaping, smoothing and refining small model parts. Flat, round and semi-circular profiles make it easier to match the filing surface to the contour being worked, whether the task is cleaning an edge, opening a curve or evening out a narrow recess. Each file is 140 mm long, with a 2.5 mm handle diameter that suits close hand control on detailed work. The double-cut surface uses 38 cuts per cm, giving the files a fine, even bite that supports a smooth finish rather than heavy stock removal. This makes the set especially suited to surface preparation on plastic scale models, while still handling Mini 4WD parts and selected metal areas where careful finishing matters. At the workbench, the different profiles help move from straight runs to rounded sections without switching to oversized tools. Black rubber grips keep the hold consistent during short filing passes, and the included vinyl case stores the 3 files together between build sessions and transport.
Gears & motor pinions
BB-01 48 Pitch Spur Gear 86T, RC spare part
300051714€4.59
The BB-01 48 Pitch Spur Gear 86T is a dedicated RC spare part for drivetrain setups that use a 48 pitch gear standard. Its circular toothed form and 86-tooth count define how it meshes with the matching pinion, making it a precise choice when a worn transmission part needs replacement or a specific gearing ratio is required for a build. This pack contains 1 spur gear. The part is intended for use with a 48 pitch pinion gear, so the tooth profile stays within the same pitch system across the gear mesh. That matters during maintenance and rebuild work, because matching pitch standards help the teeth engage correctly during rotation. The gear is shown as a molded component with a central mounting hole and reinforced face structure, details that support its role as a fitted mechanical part rather than a general workshop accessory. In practical use, the gear suits bench repairs, scheduled part changes and drivetrain refreshes on various R/C cars that accept this specification. When an RC chassis calls for an 86T spur gear in 48 pitch format, this part provides a direct, clearly defined replacement to keep the transmission setup on the intended gearing standard.
Axes & drive shafts
BB-01 D-Parts Suspension Arms, chassis spare set
300051713€12.79
The BB-01 D-Parts suspension arm set supplies the core chassis pieces that guide wheel movement at both the front and rear of a BB-01 build. With 2 front arms and 2 rear arms in the pack, the set supports a matched replacement across both ends, keeping the suspension layout consistent when worn or damaged parts need changing. Each arm is molded in glass fiber-reinforced nylon, a material choice suited to detailed chassis parts with hinge-pin mounts and outer pivot points. The shared right and left component shape reduces sorting during maintenance, since the same form is used on both sides. The included D-Parts for the BB-01 chassis focus on the mechanical areas that control suspension travel and the connection points around the wheel assemblies. This set fits workshop use, routine upkeep, or a rebuild after hard off-road sessions with a BB-01 machine. It also works as a practical spare to keep alongside other chassis parts, ready for quick replacement when the front or rear arm assemblies need attention.
Shock absorbers & springs
BB-01 Damper Adjuster V Parts, RC spare set
310225338€6.49
The BB-01 Damper Adjuster V Parts set brings front and rear damper adjuster components together on one black molded sprue for focused repair and maintenance work. Shaped rings, collars and linking pieces are arranged as separate numbered sections, so the required part can be identified before removal and fitted where the BB-01 chassis calls for it. The visible sprue layout supports clean handling at the bench, with each molded section kept in place until use rather than arriving as loose pieces. This format helps when comparing part shapes, checking orientation and separating only the needed component during a repair. The set belongs to the model supplies category and is intended for RC and model servicing rather than stand-alone play. Its compact collection of adjuster parts concentrates on one chassis area, which keeps replacement work specific instead of relying on mixed universal hardware. On a workshop table, the numbered sprue can be checked against the relevant build stage or service task before installation. For an existing BB-01 build, the set provides a direct source for renewing front or rear damper adjuster parts when the original pieces need replacement.
Axes & drive shafts
BB-01 Dogbone Shafts, RC spare part, steel
300022068€18.99
These BB-01 Dogbone Shafts are a dedicated steel spare part for the BB-01 chassis and supply a matched pair for drivetrain service. The 2 shafts use the classic dogbone layout, with a pinned ball end on one side and a cup-style joint end on the other, so rotational force can pass between connected drivetrain parts while suspension movement changes the working angle. Crafted in carbon tool steel, the shafts focus on the part of the drivetrain that sees repeated motion under load. The black metal finish and the identical left and right pieces shown in the set make them suited to a like-for-like replacement when an existing pair needs renewal. As a chassis-specific component, the fitment stays tied to the BB-01 platform rather than a broad universal range, which helps keep maintenance accurate and parts selection straightforward. On a bench build, repair session or routine drivetrain refresh, this 2-piece set covers the shaft pair in one pack. It suits keeping a running chassis in service, replacing worn transmission links, or preparing spares for future maintenance on BB-01 based RC vehicles.
Axes & drive shafts
BB-01 Front Upright Set, RC spare parts, 2 pcs
300051712€7.19
The BB-01 C-Parts front upright set supplies 2 replacement components for the front end of a BB-01 chassis, giving RC model maintenance a direct way to renew a key mounting area. Each upright is molded in glass fiber-reinforced nylon, a material choice that suits parts handling steering pivot loads, wheel support points and repeated workshop fitting. The set uses the same component shape for right and left, which simplifies parts identification when a front corner is being rebuilt. The large circular opening in each upright forms the bearing seat area, while the molded mounting points connect with the surrounding chassis hardware. As C-Parts for the BB-01 platform, these pieces belong to the chassis structure itself rather than to bodywork or trim, making them relevant for repair, upkeep and keeping an existing build in running condition. On a bench setup, the pair can replace worn, damaged or missing originals during a front-end refresh on a BB-01 model. The 2-piece format also suits keeping matching spares on hand for routine service, especially when steering and wheel support components need to be exchanged as a pair.
Other spare parts & accessories
BB-01 Main Chassis, RC spare part for BBX
319335893€21.29
The BB-01 Main Chassis is the core frame section for BBX 58719 and provides the shaped base around which the vehicle layout is built. Its black molded form combines an elongated tub design with a large central compartment, creating dedicated space for the main internal installation while keeping the underside profile structured by integrated ribbing. Across the frame, molded screw posts and cylindrical mounting areas define where matching assemblies attach, while rectangular side slots add further connection points along the chassis walls. The one-piece construction keeps the geometry consistent across the length of the frame, which matters when replacing a worn or damaged base on an existing BB-01 build. The underside view shows a symmetrical layout with reinforcement lines running through the tub, giving this spare part the form needed to carry the rest of the chassis hardware in its intended position. This replacement part suits repair work, rebuilds and parts-based restoration of a BBX 58719 using the BB-01 platform. It fits naturally into workshop sessions focused on bringing an RC vehicle back into running condition or preparing a fresh chassis foundation for the next stage of assembly.
Axes & drive shafts
BB-01 T Parts, rear suspension mount set
319225237€14.29
The BB-01 T Parts rear suspension mount set is a focused replacement and maintenance set for the specified suspension area, giving builders the exact molded shapes needed for work on the rear mounting section. The sprue format keeps the components together in one organized frame until removal, which helps with part identification before fitting begins. The visible layout includes multiple molded pieces in black and dark gray, with each shape formed for a technical role within the assembly rather than as a generic mixed parts pack. Numbered positions on the runner support orientation during workshop handling, and the molded frame format helps keep smaller connectors and bracket-style pieces grouped before installation. This makes the set useful when a damaged mount section needs renewal or when a build calls for the named BB-01 rear suspension area to be rebuilt with matching parts. On the bench, the set suits careful repair sessions, planned maintenance, or keeping key replacement parts ready alongside an existing BB-01 build. It also works well as workshop stock for model owners who prefer to keep the specified suspension mount section serviceable with the correct dedicated parts.
Gears & motor pinions
Bevel Gear Differential Set, RC spare part kit
300050602€5.99
This bevel gear differential set is a drivetrain spare part kit for selected RC chassis, built around the internal mechanism that distributes drive through a differential assembly. Supplied as a kit version, it provides 8 pieces for differential service on compatible platforms and suits repair work that focuses on the gear internals rather than the complete chassis. The set is specified for CR-01 and DT-02 chassis, making it a targeted choice when those platforms need matching replacement parts in the differential area. The included contents are 1 bevel gear differential set with 8 pieces. Studio imagery shows the internal layout clearly, with larger bevel gears, smaller mating gears, a 3-armed carrier and 2 flat washers or shims, all centered on the gear action inside the assembly. That component mix supports rebuilds where worn or damaged internal differential parts affect drivetrain function. In workshop use, this kind of set suits routine maintenance, repair after heavy running, or a planned refresh of the axle internals on a compatible chassis. It is not available for XB models, so the fit remains tied to the listed chassis platforms and their matching differential setup. Warning! Not suitable for children under 14 years.
Axes & drive shafts
Bevel Pinion Gear, spare part for model drivetrain
305455040€3.59
This bevel pinion gear is a dedicated spare part for model drivetrain service, built to pass rotational force through an angled gear interface inside a transmission assembly. The compact metal component combines a toothed upper edge with a conical body, making it suitable for mechanical layouts where direction changes within the drive line are required. Reinforced rib-like shaping along the gear body adds structural definition to the part itself, while the central mounting opening is formed for installation on a shaft or axle. That layout supports correct positioning within the surrounding mechanism and helps restore clean meshing when an original gear shows wear or damage. Supplied as 1 individual gear, it suits selective replacement work where only the affected transmission element needs to be exchanged. The plain silver-gray finish keeps the mechanical form easy to identify during maintenance and parts sorting. In workshop use, this spare gear fits repair jobs on model assemblies that rely on compact internal power transfer between connected drivetrain parts. It also serves as a practical replacement to keep an existing build in running condition after wear in a heavily used transmission section. Warning! Not suitable for children under 14 years.
Gears & motor pinions
Bevelgear Set, model spare parts for drivetrain
319440510€5.19
This bevelgear set brings the key transmission parts needed for focused drivetrain maintenance on compatible model assemblies. The set contains 5 metal gears: 2 larger bevel gears with central bore openings and 3 smaller pinion-style bevel gears with short shafts. Their angled teeth are made to mesh at intersecting shaft positions, a layout commonly used to redirect rotary motion through a compact gearbox section. The combination of larger hub gears and smaller pinions supports replacement work where worn or damaged gear teeth can affect smooth running. Because bevel gears transfer motion across a change in shaft direction, they are suited to mechanical areas where drive needs to turn through an angle rather than continue in a straight line. The silver-gray metal construction gives each gear a clearly defined tooth profile and a technical finish that matches the functional role of these parts. Compatibility is stated for BB18, BB19 and BB20, with reference to 58618 Mt.Bee. On the workbench, this set suits planned servicing, targeted repair, or keeping essential transmission parts ready for a compatible model. The clearly differentiated gear sizes also help when matching the correct meshing pair during maintenance and reassembly. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Body Mount Extension Set 5.5 mm, RC car accessory
300054604€7.99
The Body Mount Extension Set 5.5 mm adds a precise height correction to RC car body posts when a different bodyshell calls for more clearance. Each extension piece is designed to work with 5.5 mm to 6 mm diameter body mounts, and the included snap pins lock the selected position through the adjustment holes for a firm mechanical hold. Inside the set are 4 body mount extensions, plus 4 snap pins in 6 mm and 7 mm sizes. The parts are intended for touring car chassis and M-Chassis cars, where body posts may already have been cut down for another shell. Instead of replacing the full mount, this set extends the existing post by 5.5 mm and keeps the mounting point usable for another body setup. The fitting method shown in the leaflet uses the extension on the chassis-side body mount and secures it with a snap pin through the cross hole. This accessory suits workshop adjustments, shell swaps and rebuilds where body height needs a small, exact correction rather than a full change of mounts. It is compatible with TT-01, TT-02, TA05, TA06, TB-03, TB-04, XV-01, FF-03, M-05 and M-06 chassis body mounts, making it a practical addition for keeping several RC car bodyshells in rotation.
Other spare parts & accessories
Body Mount Plate BH 7/8, model accessory set
319808269€11.49
The Body Mount Plate BH 7/8 is a model accessory set for the 58441 and 58452 references named in the data. With 2 mounting plates included, it supplies the specific hardware needed for work on the body mount area, whether the goal is replacing an existing part or completing a matching assembly step on the intended build. Each plate is shown as a formed metal component with a rectangular profile, rounded corners, 2 screw holes and a shaped center section. Those details matter during installation, because the hole positions and stamped form help the plate sit in the intended location and connect with the surrounding structure as designed. The BH 7/8 designation keeps the part identification aligned with the named application, which is useful when sorting spares for maintenance or rebuild work. The compact hardware format also makes this set a focused choice when only the mounting section needs attention rather than a wider parts replacement. On a workshop table, the 2 plates can be set alongside the target chassis parts and matched directly to the specified 58441 or 58452 build. For routine upkeep, rebuilds or parts sorting, this set keeps the replacement task centered on the exact mounting hardware named in the data. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Body Mount Set, RC spare parts for DT-03 chassis
300050855€9.99
This E-parts body mount set is made for selected RC chassis and supplies the core parts needed when body fixing points need replacement. It fits DT-03, DT-03T, G6-01, G6-01TR, TL-01, FF-02 and WR-02 applications named in the data, combining molded mounts with matching hardware for a direct service task at the shell mounting area. The black components are shaped for chassis attachment and body support, while the included mounting material covers the fastening work tied to this set. Multiple hole positions on the molded parts allow the mounting point to be set according to the chassis layout and shell position, which matters when replacing worn posts or correcting body fit after use. As E-parts, these components suit maintenance benches, rebuilds and parts boxes where chassis-specific replacements need to stay close at hand. The set works well during routine RC upkeep, after a cracked mount, or when a stored chassis is being returned to running condition with the correct fixing parts. In workshop use, the combination of mounts and screws keeps the repair centered on one compatible set instead of mixing unmatched hardware from different spares. Warning! Not suitable for children under 14 years.
Axes & drive shafts
BT-01 C Parts, wheel axle spare parts set
300051732€6.99
The BT-01 C Parts set supplies original replacement components for the BT-01 chassis, centering on wheel axle and centre shaft parts used in the drivetrain. Differential cup joints, axle shafts, dogbone shafts and propeller shaft joints are grouped on one sprue, giving a direct source for matching parts when a running chassis needs repair or a rebuild calls for fresh hardware. These components handle connection and rotation transfer inside the BT-01 layout. Dogbone shafts link moving drivetrain sections, while cup joints and shaft ends sit at key handoff points between connected assemblies. Using original parts helps maintain the intended fit of the chassis design and keeps replacement work aligned with the existing BT-01 structure. The set is described as C Parts wheel axles and centre shaft, which makes its role within the chassis system clear for maintenance planning. This spare parts set fits workshop use, routine upkeep and targeted replacement after wear or damage in regular RC running. It also supports keeping a BT-01 chassis ready for the next rebuild session by covering several related drivetrain components in one pack. Compatible with the BT-01 chassis. Warning! Not suitable for children under 14 years.
Axes & drive shafts
BT-01 T Parts, RC spare parts, suspension arms
300051736€6.79
The BT-01 T Parts set is an original spare parts sprue for the BT-01 chassis, bringing together key structural pieces used around the suspension and body mounting areas. Molded in black and supplied as a single T runner, the set gives a direct source for replacing worn, damaged or missing chassis parts while keeping the fit aligned with the BT-01 platform. Alongside suspension arms, the sprue carries body mounts, bumpers and damper shafts, plus further related pieces formed as part of the same runner. The image layout shows mirrored left and right components, support posts, mounting sections and smaller braces, which helps identify each part before installation. This kind of grouped spare set is useful when several connected areas need attention at once, rather than replacing only one isolated piece. As an original spare part from Tamiya, it is intended to match the chassis design named in the data rather than serve as a universal RC car part. On the bench, the set suits routine maintenance after repeated running sessions, impact damage or a rebuild of a BT-01 chassis. It also helps keep a parts box stocked with core replacement pieces that are often needed around suspension and body support points. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
Bumper Ford Ranger Subaru Brat model spare part
319335553€19.99
This replacement bumper supports repair and upkeep on selected Tamiya vehicle builds by restoring a small but visible body detail in a single swap. The part is supplied as 1 piece and is identified in the source data for Ford Ranger and Subaru Brat applications, making it a focused choice for maintenance rather than a general universal fitting. The black moulded form shows multiple mounting points and a shaped center section that align it with model assembly hardware and body attachment areas. That layout helps when sorting spares on the bench, checking compatibility during a rebuild, or replacing a missing section after use. The source data also links the part to Sand Scorcher 58441 and 58452 references, which adds another concrete route for matching it to an existing build or parts collection. As a single replacement component, it suits targeted repairs where the rest of the vehicle remains in serviceable condition. In workshop use, a dedicated spare like this keeps restoration work moving without replacing larger assemblies. It also fits neatly into labelled parts storage for future rebuilds, especially where older Tamiya models are maintained over time and original trim details need to be brought back into place. Warning! Not suitable for children under 14 years.
Gears & motor pinions
C-Parts Gearboxguard, model spare parts for CC-01
300005521€15.79
C-Parts Gearboxguard for CC-01 supplies replacement molded components for drivetrain and chassis-area service on a compatible model build. The black sprue format keeps the individual sections together until trimming, making it easier to identify the required shapes during a repair session at the workbench. The set is presented as model spare parts rather than a complete kit, with molded guard, housing and fastening-area forms visible on the frame. Ribbed detailing, screw holes and cylindrical mounting posts support the mechanical role of the parts once fitted into the existing assembly. Several circular pieces and hexagonal cap-like forms add further replacement coverage for the same component group, which helps when an older build needs targeted maintenance instead of a full parts change. This format suits rebuilds after wear, damage or disassembly, and it also helps keep a CC-01 chassis in running condition with matching replacement sections on hand. AreBatteriesIncluded is stated as false in the data, and no battery is included with these spare parts.
Shock absorbers & springs
C.V.A II Oil-Shock-Set Super Short, damper set
300050746€26.49
The C.V.A II Oil-Shock-Set Super Short is a 48-piece damper set for assembling 2 extra short oil dampers for RC chassis applications. Its shortened format suits layouts where suspension space is tight or where a lower chassis ride height is needed without moving away from an oil-filled damper design. The set is supplied as 1 oil damper set and is intended for model use from 14 years. This version is designed for MF-01X chassis use and also matches the TT-02RR chassis, where it serves as kit standard equipment. The assembly diagrams show the working structure in detail: piston rods fit into the cylinders, O-rings and E-rings secure the moving parts, damper oil is filled into the cylinder, and the piston is moved through the oil to release trapped air before the cap is tightened. Spring installation is completed with dedicated adjuster parts, allowing the suspension unit to be built to the required kit setting. That sequence gives the set clear value for replacement, rebuild and chassis-specific tuning work. On the bench, the compact damper length helps when refreshing an existing suspension layout or preparing a chassis for a lower stance. For MF-01X rear use, 5x9 mm pillows, 19805611, are required separately. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
C.V.A.II Oil Damper Set Mini, RC shock set
300050519€36.29
The C.V.A.II Oil Damper Set Mini adds an oil-filled suspension option to compatible RC chassis and brings a more tunable setup to compact model car builds. Supplied as a 2-piece set, it is designed for builders who want to replace or refine standard dampers with an adjustable unit that can be matched to different mounting positions. Each damper can be adjusted from 55 to 70 mm, giving the set a usable range for several chassis layouts named in the compatibility list. The set is suitable for TD4, TD2, DB02, DB01, DF-03, DF-02, DT-02, DT-03, F103GT, GF-01CB, TT-02B, TT-01 TYPE-E and WR-02CB. The included damper oil supports the oil-pressure design, where the internal fluid works with the spring and shaft movement to manage compression and rebound during running. This makes the set relevant not only as a replacement part, but also as a tuning step when suspension response needs to be matched more closely to the chassis setup. On a bench build, the adjustable length helps when preparing a specific front or rear suspension position before installation. During running sessions, the oil-filled construction supports more measured chassis movement over changing surfaces and through repeated direction changes. For installation, 5 mm ball heads are required separately. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
C.V.A.II Oil Damper Set Short, RC shock set
300050520€39.49
The C.V.A.II Oil Damper Set Short brings oil-filled suspension control to a wide range of RC chassis, with 2 short dampers designed for tuning or replacement use. Its adjustable 80 to 97 mm length gives room to match the setup to different vehicle layouts, helping the suspension work with the chassis rather than against it on rough sections and changing surfaces. This set is suitable for TD4, TD2, CW-01, DB02, DB01, DF-03, DT-02 and TT-02B chassis, and the data also names Monster Beetle, Blackfoot, Lunch Box, Midnight Pumpkin, Manta Ray, Top Force, Force and Blitzer Beetle among the compatible models. That broad fit makes it useful both for restoring an older runner and for refining the handling of an active build. The oil damper format uses fluid resistance inside the shock body to smooth compression and rebound, giving a more measured suspension action than a simple friction-based setup. On the bench, the pair suits maintenance, repair and chassis-specific tuning work where damper length matters. A 5 mm ball head is required for mounting, with part 300050592 required separately, so the set can be installed with the correct attachment hardware for the chosen model. Warning! Not suitable for children under 14 years.
Axes & drive shafts
CC-01 B-Parts, steering servo saver spare set
300005520€15.79
CC-01 B-Parts brings the steering and servo saver section together in one spare parts sprue, giving compatible builds a direct route back to clean mechanical function. The black injection-molded runner presents the parts in an organized layout, with larger mirrored pieces, smaller linkage forms and circular clips arranged for clear identification at the bench. This set is intended as replacement hardware for the CC-01 rather than as a complete vehicle kit, so the focus stays on the steering assembly where accurate fit matters most. Visible molded part numbers such as 8, 9, 10, 11 and 13 help distinguish the individual shapes during preparation. The runner format keeps each component attached until needed, which supports tidier handling while checking the required section against an existing build. Glossy black molded surfaces and crisp edges reflect the technical character expected from RC maintenance parts. On a repair bench, the sprue suits worn steering sections, missing servo saver pieces or a planned refresh of an older chassis. It also fits neatly into a spares collection for hobby work, where keeping the correct CC-01 steering parts close at hand can shorten downtime between rebuild sessions.
Other spare parts & accessories
CC-01 D-Parts, body mount spare part
309005741€7.99
CC-01 D-Parts is a body mount spare part set for model maintenance on the 58324 reference. The set provides 2+2 replacement parts, making it useful when original mounting points are worn, missing or damaged and the shell needs the correct support points back in place. The designation D Parts identifies this set within the CC-01 parts structure, which helps when matching replacements to an existing build or planning a repair. As a model supply rather than a general-purpose accessory, it is intended for a specific application instead of broad compatibility across unrelated chassis types. The body mount function matters at the point where the shell is positioned and secured, so using the named replacement set helps keep that connection in line with the original layout. Batteries are not included. This spare part set fits naturally into workshop tasks such as replacing lost components during a rebuild, refreshing a used chassis, or keeping matching parts on hand for future maintenance. It also works as a practical stock addition alongside other service parts for the same CC-01 reference, especially when a repair calls for the exact D Parts designation rather than a substitute. Warning! Not suitable for children under 14 years.
Gears & motor pinions
CC-01 G-Parts, spare parts set for 58132
309005422€17.29
CC-01 G-Parts for 58132 provide a focused spare-parts set for drivetrain service, centered on molded mechanical components used in rotational power transfer. The set brings together black injection-molded gear elements and related mounting parts that suit repair work on an existing compatible model. Visible components include multiple spur gears, bevel gears, a larger gear with an integrated vertical pinion, a round plate with screw holes, and additional small parts carried on a sprue frame. That combination points to gearbox or differential-related functions where meshing teeth, axle positions and cover placement all need to match the original layout. The larger geared part with integrated pinion supports a compact transfer step within the mechanism, while the bevel gear forms indicate angled drive movement inside the assembly. The round plate adds a fitted structural piece rather than loose hardware, helping restore the intended arrangement of the surrounding mechanism. On the bench, this set suits planned maintenance, wear-related replacement, or the completion of a drivetrain rebuild when original molded parts are no longer usable. It also works well as workshop stock for model owners who keep compatible mechanical spares ready for future service on 58132-based running gear. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
CC-01 M-Parts Toyota, model spare parts, 2 pcs
309115264€26.49
CC-01 M-Parts Toyota is a spare parts set for model work on kit 58445 and provides 2 replacement parts for the matching build. The black injection-molded frame groups the components on a single sprue, so the original shapes, attachment points and part orientation stay easy to reference during repair or rebuild tasks. The molded layout shows several distinct forms, including long curved sections, mirrored arm-shaped pieces, smaller mounting blocks and round connection elements. These details matter when a damaged section needs to be replaced with a part that matches the intended geometry of the original assembly. Because the pieces remain attached to the runner before removal, each section can be identified against the build step before cutting it free. The preformed holes and connection points support clean integration with the corresponding assembly positions in the specified model. This set fits situations such as replacing lost parts during a paused build, refreshing worn sections on an existing chassis, or keeping a stored model ready for future maintenance. In a workshop drawer or alongside a current project, the sprue serves as a direct source for matching CC-01 M-Parts Toyota components tied to kit 58445. Warning! Not suitable for children under 14 years.
Axes & drive shafts
CC-01 Universal Joint, model accessory for Pajero
304135042€15.99
The CC-01 Universal Joint is a dedicated model accessory for Pajero 58132 and serves as a replacement drivetrain part where a precise rotating connection is needed. Its universal-joint design allows torque to pass between connected parts even when the angle changes, which is important on a chassis layout that moves through steering and suspension travel. Used during maintenance or repair, this component helps bring a worn drivetrain area back to a defined mechanical fit. The clear CC-01 designation keeps the application focused on the matching platform, while the Pajero 58132 reference identifies the intended model directly. That makes part selection more straightforward when servicing an existing build rather than replacing larger assemblies unnecessarily. As a single-purpose spare part, it suits bench work that focuses on keeping the drivetrain operating cleanly and consistently. In a workshop setting, the joint can be fitted during routine overhaul after extended running or when a damaged coupling starts to affect smooth rotation. It also works as a practical stock spare for model owners who maintain a CC-01 Pajero 58132 and want the correct replacement ready for the next service interval. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
CC-02 Aluminum Damper Set, chassis upgrade
300054991€94.99
The CC-02 Aluminum Damper Set equips a CC-02 chassis with 4 oil dampers built around lightweight aluminum cylinders. Their narrower shape compared with standard resin cylinders gives the suspension a more realistic scale appearance while the low-friction cylinder surface helps the dampers respond more cleanly across changing terrain. Assembly creates 4 dampers using cylinders, cylinder caps, O-ring caps, adjustable retainers and the included attachment parts. The instruction flow shows oil-filled construction with piston movement used to release trapped air before the cylinder cap is tightened, a setup that supports controlled damping rather than a simple spring-only action. Ball connectors are fitted at both ends, changing the upper mounting style used on standard CC-02 kits and allowing freer motion as the suspension works through roll. The dampers accept the chassis kit-included coil springs, and the leaflet also specifies compatibility with separately sold 12.6 x 50 mm option springs. On a trail-style CC-02 build, this set suits builders aiming for a more detailed underbody view and a more fluid suspension response over ruts, stones and side-to-side weight transfer. It also fits tuning-focused rebuilds where the damper layout is being updated without changing the chassis platform itself.
Other spare parts & accessories
CC-02 LF 6mm Ball Collar (18), chassis parts
300054945€21.19
The CC-02 LF 6mm Ball Collar set adds a focused drivetrain and suspension upgrade to CC-02 chassis cars by replacing kit-standard C9 parts with low-friction steel components. Each collar uses a plated surface to minimise resistance where moving parts pivot and slide, so link-arm action feels cleaner and more direct when the chassis works over uneven terrain. The pack includes 18 collars in total. Of these, 16 are assigned to the link arms, while 1 fits the steering linkage and 1 fits the battery plate, giving the set a chassis-specific layout rather than a generic hardware mix. The 6 mm size matches the stated fitment, and the steel construction brings a precise contact surface to the suspension hardware. In rigid suspension setups, that lower resistance helps the links move with less drag through their travel, which supports more consistent articulation across rough sections. Installed on a CC-02 build, the collars suit tuning sessions that focus on suspension response and chassis control rather than cosmetic changes. They also fit maintenance work where worn standard parts are being swapped for smoother-running hardware in the steering and link assemblies.
Axes & drive shafts
CC-02 SS Adjust Tie-Rod Set, chassis accessory
300054929€23.99
The CC-02 SS Adjust Tie-Rod Set adds a more tunable steering linkage to compatible CC-02 chassis cars by replacing the standard rigid molded link with stainless steel turnbuckle shafts. That change brings toe angle adjustment into the setup, allowing the chassis to be dialed in with greater precision for different running conditions and handling preferences. The set includes 1 x 104 mm stainless steel tie-rod, 1 x 53 mm stainless steel tie-rod, adjusters, and small attachment parts. The turnbuckle shafts feature hex adjustment sections, so length can be changed with a wrench as shown in the set documentation. This mechanism makes it possible to alter the linkage length directly through the shaft rather than removing and replacing a fixed rod. Stainless steel construction gives the main rods a durable metal format suited to repeated setup changes on the chassis. Installed in place of the standard kit linkage, the set supports fine setup work when steering response needs a more exact toe setting than the stock molded part allows. It suits bench tuning, rebuilds, and upgrade work on CC-02 based builds where adjustable linkage geometry is part of the chassis setup. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Chassis Protective Sticker, RC accessory, 0.3 mm
300054499€15.79
This hard protective film is made for the underside of an R/C vehicle chassis, where repeated contact with the track surface can leave marks during regular running. At 0.3 mm thick, it adds a thin sacrificial layer that takes the abrasion while leaving the chassis itself covered. The transparent finish keeps the visual character of the model unchanged. The sheets measure 180 x 330 mm and come in a pack of 2, providing material that can be cut to suit different chassis shapes and lengths. The highly adhesive surface is intended to bond securely under the main chassis, where constant rubbing and sliding place the greatest demand on protection. Because the film is supplied as full sheets rather than pre-cut sections, it can be adapted to a wide range of R/C vehicle layouts. This makes it useful both for a fresh application and for replacing worn film after repeated use. In workshop preparation, the film can be trimmed before a run and applied to the areas most exposed to scraping. After track sessions on abrasive surfaces, the protective layer helps keep the underside cleaner in appearance and reduces direct wear on the chassis base.
Other spare parts & accessories
Craft Tweezers, papercraft tool, 140 mm
300074080€22.49
These craft tweezers are designed for papercraft work, where small tabs, narrow folds and glued sections need controlled handling. At 140 mm in length, they offer a compact format that sits easily in the hand while keeping the tip visible during close, detailed tasks. The foremost part uses an original TAMIYA design created to improve effectiveness in gluing, paper bending and the drying process. That shape helps hold and guide thin paper parts with more control than fingertips alone, especially when working along edges, corners and tight contact points. The tweezers are made from SUS410 stainless steel and finished with a hairline surface, giving the tool a precise, clean look suited to bench work and hobby tables. The pointed, angled form also helps reach into small spaces between folded sections without covering the working area. Sticker and decal application is another practical use, particularly when small markings need careful placement before final pressure is applied. On a papercraft build, during detail finishing, or while handling delicate printed parts, these tweezers support steady, accurate movements across each step of the work. Warning! Not suitable for children under 14 years.
Axes & drive shafts
Cup Joint Universal Shaft for TT-01 DF-02
300053790€21.29
This Cup Joint Universal Shaft is a drivetrain spare part for TT-01 and DF-02 chassis setups, built to work at the gearbox in combination with an assembly cardan shaft. The pot joint design is intended to suppress drive losses, supporting smoother running when the drivetrain is under power. The set contains a left and a right part, giving the specified pair needed for the matching drivetrain layout. Its application is clearly defined for use with the DF-02 Assembly Universal Shaft 53791 or the Assembly Universal Shaft for TT-01 and TA04 53792. That makes it a focused choice for maintenance, replacement, or a driveline setup built around those universal shaft systems. The compact metal parts are shaped for precise fit within the transmission area, where clean engagement matters for consistent rotation. On the bench, this kind of component belongs in rebuilds, wear-part replacement, or a planned drivetrain update on compatible chassis. In running use, the gearbox connection and universal shaft pairing support a more fluid transfer of drive through the system, especially where a correctly matched left and right set is required. Warning! Not suitable for children under 14 years.
Axes & drive shafts
D-Parts F/R Upright, model spare part, 1 pc.
300005296€14.49
D-Parts F/R Upright is a model spare part for selected Tamiya vehicle builds and is supplied as 1 piece. The molded black component is shaped for front and rear upright use, making it a practical choice when an original part from a compatible chassis setup needs replacement during maintenance or repair. The part is specified for compatibility with 58321, 58232 and 58256. Its form combines mirrored upright sections with circular housings, angled support arms, fastening holes and molded connection points in a single unit. That layout matters during repair work because the geometry of an upright part affects how surrounding running gear components line up and mount. Replacing a worn or damaged section with the correct designated part helps restore the intended fit within the assembly area. This spare part suits workshop stock for ongoing model upkeep, rebuilds after heavy running, or the completion of an older chassis that needs the original designated component. Kept alongside other maintenance parts, it supports faster repairs when a compatible model returns to the bench for service or parts replacement.
Shock absorbers & springs
Damper Bag BF1-8, spare parts set for 58441/58452
319401427€44.99
The Damper Bag BF1-8 is a spare parts set for the Tamiya references 58441 and 58452, bringing 28 damper-related components together in one pack for targeted maintenance work. Silver tube sections, rods, caps, bushings and translucent spacer rings form a compact hardware assortment that suits repair tasks where the original suspension parts need replacement. The included contents are listed as 1 damper set with 28 pieces, making the pack a focused source for the small components that are often needed during servicing. The BF1-8 designation helps identify the correct parts group for the stated model numbers, which is useful when matching replacement hardware to an existing build. The mix of metal-look and molded parts shown for the set points to several connection and spacing functions within the damper assembly rather than a single loose replacement part. On the workbench, this set fits routine model upkeep, rebuilds after wear, or the replacement of lost small parts during disassembly. For compatible 58441 and 58452 builds, the grouped contents make it easier to restore the damper area with matching pieces kept together in one set. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
Damper Bushing, model spare part set of 8
319808279€12.29
This set provides 8 damper bushings for model maintenance and replacement work, giving matching inserts for assemblies that use this compact flanged format. Each piece is shown in black with a cylindrical body, a central hole and a lip on both sides, a shape that supports seated placement in the intended mounting point. The small format makes the set useful when a worn insert needs to be exchanged or when spare bushings are kept ready alongside other service parts. Because all 8 pieces share the same form, the pack supports consistent replacement across the same assembly area. The through-hole design suits fastening or guided pass-through where the matching model layout calls for a bushing, while the flanged edges help the part sit in place within the corresponding opening. On the workbench, this kind of spare part belongs in regular upkeep for model vehicles and related mechanical builds that use damper-mounted components. The set can be used during repair sessions, rebuilds or planned maintenance, where fresh bushings help return the intended fit of the original assembly. Warning! Not suitable for children under 14 years.
Screws & ball head screws
DB-01 3mm Thin Alum. Lock Nut, RC accessory
300054155€9.79
The DB-01 3mm Thin Alum. Lock Nut set adds a compact aluminum fastening option to compatible RC chassis, with 5 blue anodized lock nuts included in the pack. The 3 mm format suits platforms that use this hardware size, and the thin profile helps when surrounding parts leave little room for a taller nut. This set is intended for a broad list of chassis named in the data, including DB01, DB02, DN-01, F104PRO II, F104Ver.II PRO, F104W, F104, M-08 CONCEPT, TA07 MS, TA06 MS, TA06, TA06 PRO, TB-Evo.7, TC-01, TRF503, TRF502X, TRF420X, TRF420, TRF419XR, TRF419X, TRF419, TRF211XM, TRF201XMW, TRF201, TRF103, TRF102, TRF101, XV-02PRO, XV-01 Chassis, XV-01 PRO and XV-01T. Aluminum construction reduces weight compared with standard metal hardware, while the lock-nut form is made for fastening duties on running chassis. For workshop maintenance, rebuilds or detail-focused upgrades, the 5-piece set provides matching hardware for multiple mounting points on one chassis. The blue anodized finish also gives exposed fastening points a more technical appearance on race-oriented and off-road builds. Warning! Not suitable for children under 14 years.
Screws & ball head screws
DB-01 5mm Heavy Duty Adjuster, spare part, 8-pack
300051283€6.39
The DB-01 5mm Heavy Duty Adjuster set supplies 8 matching spare parts for maintenance and rebuild work on compatible model assemblies. Each adjuster is specified with a 5 mm ball end and a 25 mm length, giving a clearly defined replacement dimension when an existing linkage needs the same format again. The set is described as a heavy duty version, making it a direct choice when the required part callout is DB-01 and the 5 mm, L=25 mm specification is needed. The scope of delivery contains 8 ball head pans, which supports replacing several worn connection points at once or keeping identical parts ready for later service work. The repeated format across all 8 pieces also helps maintain a consistent setup across the same mechanical area. On the workbench, this set fits naturally into routine repair, parts sorting and planned upkeep of a DB-01 build. Matching dimensions make comparison with removed hardware straightforward, and the 8-piece quantity suits both immediate replacement and keeping reserve parts on hand for future maintenance. Warning! Not suitable for children under 14 years.
Screws & ball head screws
DB-01 5x5mm Al.Ball Connector, model accessory
300054209€18.79
The DB-01 5x5mm Al.Ball Connector set adds a precise moving joint to compatible model assemblies, combining lightweight aluminum construction with a fluorine coating for smooth, lasting action at the linkage point. Each connector uses a spherical head, narrow neck and threaded shaft layout that suits pivoting connections where clean movement and repeatable fit matter. A fixed 4 mm distance from the seat bottom to the cushion ball gives this hardware a defined geometry for suspension setup changes, opening a wider adjustment range than a standard unspecified fit. The hexagon head supports firm tool engagement during installation, which helps when tightening small hardware into a chassis or suspension mount. The set contains 5 matching connectors, making it suitable for replacing worn parts or keeping identical hardware across several connection points. The metallic finish and compact 5x5 mm format suit detailed maintenance work where small differences in fit can affect movement. On a workbench, these connectors suit rebuilds, tuning sessions and routine parts replacement on a DB-01 based setup. They also fit neatly into a spares box for trackside servicing when linkage hardware needs a quick swap to restore smooth articulation. Warning! Not suitable for children under 14 years.
Screws & ball head screws
DB-01 5x5mm Ball Connector, RC chassis part
300053906€18.29
The DB-01 5 x 5 mm aluminium ball connector adds a compact adjustment point to compatible R/C chassis and supports more precise upper arm positioning where setup changes matter. Its blue anodised finish and hex head format give the small hardware piece a clean technical look while keeping installation focused on a defined mounting point. This version reduces the length from the bearing surface to the ball joint from 5 mm to 4 mm, increasing the available adjustment range on competition-capable chassis. The connector is manufactured from high strength aluminium and uses a threaded shaft with a rounded ball head for linkage attachment. A hexagonal hole accepts a 2 mm wrench for controlled tightening, and the instruction sheet notes that spacers can be used if needed to adjust position further. Compatibility covers a broad list of platforms including DB02, F104Ver.II PRO, FF-04 EVO, M-07 CONCEPT, M-08 CONCEPT, TA07 PRO, TA08 PRO, TB-04, TB-05 PRO, TC-01, TRF419, TRF420, TT-02 TYPE-S and XV-02PRO. In workshop use, this hardware suits rebuilds, replacement of worn mounting points and setup revisions across touring, formula and rally chassis in the supported range. The pack contains 5 ball heads, allowing several connection points to be updated in one session. Warning! Not suitable for children under 14 years.
Screws & ball head screws
DB-01 5x5mm Steel Hex Head Ball Connector Set
300053968€14.99
The DB-01 5x5 mm Steel Hex Head Ball Connector set adds a precise metal connection point to RC chassis assemblies where compact hardware and clean fit matter. With 5 matching parts in the pack, it suits repair work, routine maintenance and fresh builds that need consistent ball-end mounting points in a small format. Each connector uses a threaded screw shaft below a flange and rounded ball top, a layout commonly used where a linkage, rod end or ball cup needs to pivot around a fixed point. The 5x5 mm dimensions support installation in tight spaces, while the hex head format helps with controlled fitting during assembly or replacement. High-strength steel gives these connectors the material basis for demanding off-road use, and the same parts can also be installed in on-road chassis. In workshop use, this set supports quick replacement of worn connection hardware on compatible RC models and keeps matching spare parts ready for setup changes. The pack contains 5 ball heads. With compatibility stated as any chassis, the set can serve as a useful stock hardware option across different model car platforms and parts boxes. Warning! Not suitable for children under 14 years.
Screws & ball head screws
DB-01 5x8 mm Ball Connector, RC chassis part
300053907€18.29
The DB-01 5x8 mm Al.Ball Connector set brings a compact aluminium tuning part into suspension setup work on compatible RC chassis. Each connector uses a blue anodized finish and a 5x8 mm format, creating a clean fit for linkage points where precise geometry changes matter during maintenance and track preparation. A key detail lies in the revised distance from the seat bottom to the cushion ball, reduced from 5 mm to 4 mm. That change broadens the available suspension adjustment range and opens finer setup steps than a standard layout allows. The hexagonal hole type supports secure tightening, so each connector can be installed with firm tool engagement rather than relying on a plain slot or rounded head. The set contains 5 ball heads, giving enough hardware for targeted replacement work or coordinated changes across multiple mounting points. Compatibility is stated for the TA05, TRF415MSX and TB Evolution IV chassis, making the set a focused choice for workshop stock, rebuilds and setup revisions on those platforms. During routine servicing, the compact dimensions and defined fit help keep suspension links moving through their intended range while supporting repeatable adjustment work. Warning! Not suitable for children under 14 years.
Screws & ball head screws
DB-01 Ball Head Connector, RC spare part, 5x8 mm
300053969€14.99
The DB-01 5x8 mm Ball Head Connector set adds a compact steel mounting point wherever an RC chassis needs a snap-on linkage connection. Each of the 5 connectors combines a spherical ball head, a short neck and a threaded shaft, creating a clean interface for articulated parts that need controlled movement during running and setup work. The 5x8 mm dimensions make this hardware easy to match to existing assemblies when worn connectors need replacement or a fresh build calls for uniform fittings across several mounting positions. High-strength steel gives these parts the material basis for demanding off-road racing use, where repeated movement and chassis loads act directly on small connection points. The same connector format can also be installed on on-road chassis, so one pack covers more than a single vehicle type. Scope of delivery: 5 ball heads. In workshop use, the set suits routine maintenance, rebuilds after heavy track sessions, or stocking spare hardware for race-day repairs. The compact size also makes it practical for builders who want matching connector geometry across steering links, suspension links or other articulated mounting points that use this format. Warning! Not suitable for children under 14 years.
Screws & ball head screws
DB-01 Dust Cover Ball Head Adjuster Set 20pc
300053980€5.39
The DB-01 Dust Cover Ball Head&Adjuster(20) is a general use option part made to protect the connection joints between ball connectors and adjusters in the suspension system. By covering these exposed joint areas, it helps maintain smooth suspension operation during repeated use and supports more consistent movement where the linkage needs to articulate freely. This set contains 20 dust covers and is intended for chassis maintenance, replacement work and fresh builds that use ball connector and adjuster linkages. The part focuses on the joint itself rather than the whole suspension assembly, adding protection exactly where dirt and wear can affect the connection. Its general use design makes it suitable across a broad range of compatible model chassis rather than limiting fit to a single platform. In workshop use, the covers can be fitted during routine servicing when suspension links are checked, cleaned or renewed. They also make sense as spare stock for rebuilds, tuning sessions or keeping several chassis ready for running with protected linkage points. Compatible with any chassis. Warning! Not suitable for children under 14 years.
Axes & drive shafts
DB-01 Fluorine Coated Suspension Balls, RC parts
300053709€16.79
DB-01 Fluorine Coated Suspens. Balls(8) is a suspension hardware set for RC chassis tuning and maintenance. The fluorine coating reduces friction between each suspension ball and its mount, which supports more fluid suspension movement when the chassis changes direction, settles into corners or reacts to surface input. The scope of delivery contains 8 balls for wishbone shafts, making this set suitable for replacing worn contact points with matching hardware across the suspension assembly. Compatibility reaches across several Tamiya chassis families: TA06, TA06 PRO, TA06 MS, TB-03 VDS and TA05 ver.II use these balls with 54064-54074 and 54171-54175. FF-03, FF-03 PRO, TB-03, TB-04 and TB-04 PRO use them with 54064 to 54074. M-07 CONCEPT and M-08 CONCEPT use them with 54760, while TC-01 uses them with 54760 and 54787. This suspension set suits regular workshop servicing, chassis refreshes and targeted setup work where smooth ball-to-mount movement matters. It also fits neatly into a spares box for track days or bench maintenance, with 8 matching pieces ready for the specified chassis applications. Warning! Not suitable for children under 14 years.
Gears & motor pinions
DB-01/TRF501X Pinion Gear 24/25T 48DP Set
300054218€16.79
The DB-01/TRF501X Pinion Gear 24/25T 48DP set adds a focused drivetrain tuning option to compatible RC chassis with 2 metal pinion gears in 24T and 25T sizes. The 48 pitch format and newly designed tooth profile are intended to reduce noise and friction loss, supporting a cleaner mesh and a smoother running feel during track sessions, maintenance work or ratio changes. Each gear uses 2 grub screw attachment holes, so the fastening position can be selected during installation on the motor shaft. The set also comes with 3 grub screws and an L-shaped hex key for fitting and adjustment. This makes the set useful both as a replacement for worn drivetrain parts and as a practical gearing option when refining acceleration, response or running characteristics on a supported chassis. Compatibility covers DB01-Chassis, DB02-Chassis, DN-01-Chassis, TD2-Chassis, TD4-Chassis, TRF201-Chassis, TRF201XMW-Chassis, TRF211XM-Chassis and TRF502X-Chassis. For TD2-Chassis and TD4-Chassis, use with 22031 is required. On the bench, the 24T and 25T choice allows quick comparison between 2 gearing steps while keeping the same 48DP standard across the setup. Warning! Not suitable for children under 14 years.
Gears & motor pinions
DB-01/TRF501X Spur Gear, RC spare part, 91T 48DP
300051314€6.99
The DB-01/TRF501X Spur Gear 91T 48DP is a dedicated RC spare part for compatible drivetrain setups, combining a 91-tooth count with a 48 pitch tooth profile for precise transmission matching during maintenance or repair. Built for use with the DB01 and TF503 chassis named in the data, it gives the drivetrain a clearly specified replacement component rather than a generic gear. The 91T layout determines the driven gear size within the transmission, while the 48DP format identifies the fine tooth pitch used for correct meshing with the matching pinion. That makes this gear relevant when restoring the original gearing arrangement on a compatible chassis after wear, damage or routine workshop service. As a model supply in the Models & Accessories range, it suits bench work focused on drivetrain upkeep rather than cosmetic changes. The listed designation DB-01/TRF501X also helps place the gear within specific RC platform families. In practical use, this spare part belongs in the workshop alongside other transmission service components for compatible off-road chassis builds. During maintenance sessions, it supports a straightforward parts swap that keeps the drivetrain specification aligned with the stated 91T 48DP format for continued running on the correct platform. Warning! Not suitable for children under 14 years.
Axes & drive shafts
DF-02 B-Parts Upright/Steering Arm Spare Set
300051076€14.29
DF-02 B-Parts Upright/Steering Arm is a chassis spare set for the DF-02 and TT-02B platform, built to restore key steering and wheel support points with matching replacement components. The black molded parts are arranged as 4 sprues with 20 pieces, making this set a practical choice when worn or damaged suspension and steering sections need to be renewed. The upright and steering arm shapes handle pivot and linkage mounting duties within the front end layout, while the mirrored forms support correct left and right installation. Multiple mounting holes are formed into the parts for chassis attachment and linkage connection. The set also includes 4 wheel nuts and 8 washers, adding the fastening hardware needed for the relevant assemblies. As a dedicated spare set, it suits routine maintenance, repair work after running sessions, or keeping workshop stock ready for future rebuilds. On the bench, the parts help bring a DF-02 or TT-02B chassis back into running condition with matching replacement geometry instead of mixed substitutes. For hobby maintenance, rebuild projects, or replacing damaged steering components after track use, this set keeps the fit focused on the specified chassis types. Warning! Not suitable for children under 14 years.
Axes & drive shafts
DF-02 Drive Shaft Set, RC spare part, 64 mm
300051081€13.29
This DF-02 Drive Shaft set provides a direct spare part solution for the DF-02 chassis and includes 2 drive shafts with a stated length of 64 mm. The matching pair format suits maintenance work where both sides of the drivetrain need the same part specification, keeping the assembly consistent across the axle setup. Each shaft follows a straight cylindrical form with ball-shaped ends and cross pins for connection at the mounting points. That layout is designed for mechanical transfer within the drivetrain while matching the geometry required by the DF-02 platform. The black finish and compact rod profile make the parts easy to identify during a rebuild or parts check. As replacement components rather than a general accessory, these shafts are intended for the named chassis application instead of broad multi-model use. The set fits routine workshop tasks such as replacing worn transmission links during servicing, refreshing a stored chassis before running, or keeping matching spare parts ready for a future repair. In a bench setup focused on DF-02 maintenance, the 2 included shafts cover a complete paired change with the specified 64 mm dimension. Warning! Not suitable for children under 14 years.
Axes & drive shafts
DF-02 E-Parts, spare parts set, wheel axle
309005756€9.79
The DF-02 E-Parts set provides replacement components for the wheel axle and differential joint area, giving compatible model maintenance a direct route to restoring key drivetrain connections. Black moulded parts are supplied on sprues, with the axle-related and joint-related sections grouped for clear identification before removal and fitting. This spare parts set is designated as E Parts for 58328 and is intended for focused servicing rather than broad replacement across unrelated assemblies. The visible component mix includes cylindrical axle-linked pieces, connector forms and longer structural elements that belong to the same parts tree. Keeping these pieces together on one runner helps confirm part shape and orientation during workshop preparation. The set format also suits repair benches where damaged drivetrain sections need matching replacement geometry from the original parts family. Used during maintenance, rebuilds or parts replacement after wear, the DF-02 E-Parts set supports continued running with the correct component group kept on hand. It fits naturally into a spares collection for model upkeep, especially when the axle and differential connection points need renewed parts to return a chassis to working order. Warning! Not suitable for children under 14 years.
Gears & motor pinions
DF-02 Metal Parts Bag A, model spare parts
309400152€30.49
DF-02 Metal Parts Bag A is a model spare parts set identified in the source data for 58328. The designation points to a defined replacement pack rather than a general accessory, making it a practical choice when an existing build needs the matching hardware group restored or completed. The stated metal construction gives this set a clear material identity, while the DF-02 naming keeps the part reference specific for workshop organisation. As a parts bag, it suits maintenance, repair and replacement tasks on a compatible build already in use. The source data places it in model supplies, which fits its role as a support component for an established model rather than a standalone vehicle or assembly kit. This also helps when sorting spares by platform and bag reference during bench work. On the work surface, a clearly named replacement pack saves time during upkeep because the part group is already narrowed to DF-02 Metal Parts Bag A for 58328. It works well as a stock spare for routine servicing, for completing an older build, or for replacing missing original metal components with the specified bag reference. Warning! Not suitable for children under 14 years.
Axes & drive shafts
DF-02 Universal Shaft Assembly, RC drivetrain set
300053791€56.99
The DF-02 Universal Shaft Assembly is an RC drivetrain upgrade set built to cut friction where the axle moves through the steering angle. In place of a standard dog bone drive shaft, the universal joint layout keeps power delivery more direct while the front end changes direction, which helps the chassis carry drive more cleanly through bends and technical sections. The set contains 1 ball cardan shaft set with 13 pieces and is built around 2 universal shafts. Visible components include wheel axle parts, cross joints, pins, grubscrews, AW grease and a hex wrench for assembly. The shafts are marked 70, and the document notes grease application at multiple moving contact points in the joint and cup areas. The assembly is designed to be taken apart again, which allows consumable parts to be replaced when wear appears instead of discarding the full shaft unit. Fitment is specified for DF-02, DT-02, DT-03, DT-03T and TT-02B chassis with the matching cup joints listed in the data. On a buggy set up for repeated steering input, jumps and direction changes, this drivetrain layout supports a more consistent feel at the driven axle and gives maintenance-focused builders a clear upgrade path within compatible Tamiya chassis. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
DF-03 B-Parts Damper Stay, chassis spare part
300051249€11.99
The DF-03 B-Parts Damper Stay set is a chassis spare part made for the DF-03 platform and supplies front and rear stay components in one pack. Its molded black parts follow the original mounting pattern, so repair work can focus on restoring the suspension mounting area with the correct fit for this chassis. Several hole positions are built into the stays, giving the assembly clear fastening points where dampers and related hardware attach. Ribbed reinforcement details are formed into the parts, and the set also shows a metal brace element fixed with screws and washers for added structure in the mounting section. This combination suits routine maintenance, replacement after wear, or rebuilding a used chassis with the proper B-parts section rather than mixing unmatched components. On the bench, the set supports a straightforward refresh of damaged front or rear mounting points on a DF-03 build. It also fits parts storage for racers and hobby workshops that keep chassis-specific replacements ready for service between running sessions. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
DF-03 Chassis, RC spare chassis frame
309335449€13.99
The DF-03 Chassis serves as the structural core for a compatible RC vehicle build, forming the main lower frame that carries the mechanical layout. Its black molded construction combines an elongated central body with raised side sections, giving the assembly a defined platform for attaching major modules while keeping the underside compact and purposeful. Across the frame, multiple drilled and countersunk mounting holes create fixed attachment points for screws and hardware. A large oval opening in the center is joined by shaped slots and recessed areas, which help organise the placement of installed parts and leave room for routed connections within the chassis layout. One end uses a rectangular mounting section with 4 visible countersunk holes, while the opposite end extends into a flat plate with additional drilled points for further fitment. These details make the frame more than a simple base plate: it establishes the geometry that the rest of the DF-03 build follows. Used as the lower platform in a rebuild, repair or replacement project, this chassis frame supports a clean restart when an existing vehicle needs a fresh foundation. It also suits workshop stock for keeping a compatible DF-03 machine in running condition after wear or damage to the original frame. Warning! Not suitable for children under 14 years.
Axes & drive shafts
DF-03 D-Parts Rear Upright Hub Carrier Set
300051251€9.59
The DF-03 D-Parts Rear Upright Hub Carrier set is a chassis-specific replacement set for the DF-03 platform, supplying the molded parts used in the rear upright and hub carrier area. With 1 D parts tree and 6 parts in the box, it gives the build a direct source for the designated components when maintenance, rebuild work or part replacement is due. The set is focused on one defined chassis section rather than a mixed hardware assortment, which keeps part selection clear during workshop use. The molded layout on the runner helps identify each piece before removal and fitting, especially when comparing worn parts against fresh replacements. Because the set is tied to the DF-03 chassis, it suits repairs that need the matching geometry and mounting form for that platform. The rear upright and hub carrier area plays a key role in how the corresponding rear assembly is put together, so using the intended parts helps restore the specified structure of that section. On the bench, this set fits naturally into routine servicing, rebuilds after heavy running, or a planned stock of spare chassis parts. It also works well as a replacement pack to keep alongside a DF-03 model, so the required rear section components are on hand when a damaged part needs to be exchanged. Warning! Not suitable for children under 14 years.
Gears & motor pinions
DF-03 Gear Parts Bag, RC spare parts set
309400411€39.99
The DF-03 Gear Parts Bag for 58370 focuses on one of the most important working areas in an RC drivetrain: the differential. This spare parts set brings together the core service components needed when the original assembly shows wear, so the drive system can return to clean, controlled power delivery under load. The set is presented as a dedicated bag for the DF-03 and, based on the included contents, covers the internal differential hardware rather than general chassis maintenance. Visible parts include a large metal gear with shaft, a smaller metal gear, 2 black outdrives, 2 black differential housings or cams, 4 large shim washers, additional small shims and washers, 2 metal pins, 2 groups of ball bearings, 6 white bushings or spacers, 4 coil springs, and a tube marked Ball Diff Grease. That combination supports rebuild work, replacement of worn running parts, and fine adjustment of the differential stack. On the bench, the mix of gears, bearings, shims and grease gives a clear route for servicing a used transmission assembly or refreshing a stored chassis before the next run. As a model-specific spare parts bag for 58370, it also helps keep maintenance organised when a DF-03 build needs the correct drivetrain components close at hand. Warning! Not suitable for children under 14 years.
Axes & drive shafts
DF-03Ra Assembly Universal Shaft RC Parts Set
300053792€35.49
The DF-03Ra Assembly Universal Shaft brings a serviceable drivetrain upgrade to compatible RC chassis, combining a ball cardan shaft layout with high-precision machining that reduces the stalling feel during steering and supports smoother cornering. In the workshop or at the track, the metal shaft parts, pins and couplers form a focused tuning set for driveline maintenance and response. The scope of delivery contains 1 ball cardan shaft set with 13 pieces. Visible set contents include 2 long shafts marked 39, joint hardware, pins, set screws, an L-shaped hex key and AW anti-wear grease for the moving contact points. The PTO shaft can be assembled and disassembled, which allows worn consumable parts to be exchanged instead of replacing the whole assembly. That serviceable layout helps keep the driveline working with the same intended action over repeated running sessions. Compatibility is specified for TT-02 chassis, TT-02D chassis, TT-02FT chassis, TT-01 TYPE-E chassis and TT-01D TYPE-E chassis when combined with the listed companion parts. This makes the set suited to targeted repair work, drivetrain upkeep and handling-focused tuning where steering load and cornering smoothness matter most. Warning! Not suitable for children under 14 years.
Gears & motor pinions
Diff. Gear Bag Grasshopper Hornet Spare Parts
319115010€6.49
This spare parts set is made for differential service on compatible Grasshopper and Hornet RC models. Supplied as a 6-piece gear bag, it focuses on one specific drivetrain area and gives repair or rebuild work the matching gears needed for a direct replacement task. The set belongs to the model supplies range and is intended for maintenance rather than first-time vehicle assembly. By concentrating on the differential section, it helps address wear in a part of the drivetrain that affects power transfer during running. The bag format keeps the relevant gears grouped together for workshop use, whether the job involves replacing worn parts or refreshing an older compatible chassis. Compatibility is stated for Grasshopper and Hornet, so the set can be selected for those named models without adding unrelated universal-fit claims. On the bench, this kind of replacement set fits routine upkeep, targeted repairs and parts storage for future service work. It is a focused choice for RC model maintenance where the differential needs the correct matching gear components rather than a general mixed spares assortment.
Other spare parts & accessories
DN-01 Inner Sponge Front Kit, foam insert set
300051448€6.69
DN-01 Inner Sponge Front Kit is a front foam insert set for selected buggy chassis, built to sit inside the front tyres and support their shape while the model is running. The set contains 2 grey open-cell foam rings and is specified for DT-03, DT-03T and DT-02 chassis applications. Inside the tyre, each insert fills the cavity between tyre and wheel so the front end keeps a more defined profile as loads shift through steering inputs and uneven ground. The donut-shaped foam form shown in the set is intended for front use, which matters when tuning the balance of a buggy around turn-in and directional control. Compatibility is stated with tyre references 51207 and 54284, giving a clear match point when replacing worn inserts or building a fresh wheel and tyre setup. The foam material also keeps the setup light compared with heavier internal fillers. This 2-piece set suits routine maintenance, a chassis refresh or a second wheel set prepared for another surface. On a running DT-03, DT-03T or DT-02 build, fresh front inserts can help restore a more even tyre profile after repeated use and compression. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Double-Sided Tape 20mm x 2m, black tape roll
300054693€14.79
This black double-sided tape gives R/C model work a clean, practical way to mount and protect equipment in one step. The 20 mm x 2 m format provides a continuous roll that can be trimmed to the exact length needed, whether the task calls for a short fixing point or a longer contact strip across a wider surface. Its heat-resistant construction suits model layouts where mounted components sit close to running electronics and need a dependable adhesive layer between parts and the chassis or mounting surface. The foam-style tape profile also helps create a slight buffer where equipment needs both attachment and a degree of separation from the surface below. Compared with pre-cut strips, the roll format keeps sizing flexible during bench work and repeated maintenance. It can be cut for receiver boxes, electronic modules or other onboard components where tidy placement matters. One roll is included.
Axes & drive shafts
Drive Shaft, RC spare part, steel, 45 mm
309805551€12.99
This RC spare part supplies 2 steel drive shafts at 45 mm length for model vehicle drivetrains that use ball differential drives. The shaft format matches Manta Ray and Fire Dragon applications named in the data, giving a direct way to replace worn drivetrain links while keeping the intended mechanical layout in place. Each shaft uses a long steel rod with formed ends that sit into the drivetrain connection points, where rotation is passed through the linked assemblies. The 45 mm measurement matters in this role because shaft length determines how the connected parts line up during running. With 2 identical pieces in the pack, both sides can be fitted with the same specification instead of mixing different lengths or constructions. The part is listed for bowling and ball differential drives, so the stated drivetrain type stays clear when selecting the replacement. This kind of spare part suits repair work, routine maintenance and the refresh of an older chassis that needs the original shaft format restored. It can also be paired with the matching ball cardan shafts named in the data when a compatible drivetrain setup is being completed with related components.
Axes & drive shafts
Drive Shaft, spare part set for 58087 model
309805370€13.99
This spare part set provides 2 drive shafts for model 58087 and focuses on one clear job: replacing the matching drivetrain components with the correct designated parts. The shafts shown combine a long metal rod with white end connectors and protruding metal pins, giving the assembly the connection points needed for the intended mounting position. As a dedicated replacement set, the value lies in fit and function for the specified model rather than in generic compatibility. The 2-piece format suits repairs where both corresponding shafts are changed together, and it also supports planned maintenance when worn drivetrain parts need renewal. The metal rod section forms the main shaft body, while the molded end pieces create the shaped interfaces required by the assembly. This keeps the repair focused on the exact component group named in the set. On the workbench, these drive shafts suit routine servicing, rebuilds after wear, or the completion of an unfinished model that is missing original running parts. For collectors and builders maintaining model 58087, the set supplies the exact replacement category needed for a clean, model-specific repair. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
DT-01 Damper Bag, RC spare part for 58205
309415375€14.89
The DT-01 Damper Bag for 58205 is an RC spare part set built around 4 matching suspension units with red molded bodies, silver coil springs, inner rods and mounting eyelets at both ends. These parts are shaped to connect directly into the suspension layout of the specified model, restoring the moving link between attachment points when the original dampers are worn or damaged. Each damper combines a cylindrical upper housing with a visible spring wrapped around the center section, plus a lower end designed for secure mounting. That construction matters during maintenance because the spring and rod assembly allows controlled suspension movement instead of a fixed connection. The matching format across all 4 parts also supports balanced replacement work on multiple corners of the chassis rather than mixing different damper types. As a dedicated DT-01 spare part for 58205, the set is focused on repair, upkeep and keeping the running gear mechanically complete. On the bench, the bag suits routine servicing, rebuilds after heavy use and the replacement of missing or tired suspension parts. Once fitted, the dampers return the model to a setup with the correct spring-supported linkage for rolling, steering and general chassis movement. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
DT-02/03 B Parts, axle pad holder spare sprue
300004252€5.49
This spare B parts set supplies the Fighter axle pad and holder components for DT-02 and DT-03 chassis work, giving repair and maintenance builds the exact molded section needed for a clean replacement. The black parts are supplied on 1 sprue, so the full group stays together until the required section is removed and fitted. The set is specified as B parts for Super Fighter G DT-02 reference 58340, which makes it a focused choice for restoring the original layout rather than substituting unrelated hardware. The sprue format also helps with bench organisation, because each connected section remains easy to inspect before trimming. The visible molded structure supports careful handling of smaller mounting areas while the remaining pieces stay attached to the runner. For workshop stock, a single replacement sprue is also straightforward to sort and store alongside other chassis-specific service parts. This set suits rebuilds after wear, damage or missing pieces, and it also fits planned maintenance when a chassis is already apart for service. On the workbench, the connected layout makes it easier to compare the replacement section with the installed part before the swap begins. Warning! Not suitable for children under 14 years.
Axes & drive shafts
DT-02/03 Upright L/R, RC spare part set
300555059€10.19
The DT-02/03 Upright L/R is a dedicated RC spare part set for restoring the front end of compatible chassis builds. Supplied as left and right uprights, the set replaces the side-specific mounting pieces that support wheel assembly and connected steering or suspension movement during running. Its value lies in precise fitment for the DT-02 and DT-03 platform family, where a damaged upright can affect alignment and interrupt smooth operation. Replacing the affected parts with the correct upright pair helps bring the chassis back to its intended layout without changing unrelated assemblies. The compact parts format also suits the usual maintenance cycle of hobby-grade RC vehicles, where individual wear points are renewed as needed rather than swapping complete sections. For bench work, the set is easy to sort, store and match to the relevant repair task because the application is clearly defined in the designation. This spare part set fits naturally into routine buggy upkeep after repeated use, contact with track barriers or general wear in the front corner area. It also serves as a practical stock part in a workshop drawer, ready for scheduled maintenance or a direct replacement when a DT-02 or DT-03 chassis needs the correct upright on each side. Warning! Not suitable for children under 14 years.
Screws & ball head screws
DT-03 3x46mm Screw Pin, model spare part
319805976€3.19
The DT-03 3x46mm Screw Pin set supplies 4 matching replacement fasteners for compatible DT-03 model assemblies. Each pin measures 3 x 46 mm, giving a clearly defined format for maintenance work where the original hardware needs to be renewed with the same dimensions. The screw pin layout combines a long shaft with a threaded fastening function, supporting clean installation at the intended mounting point. The set format keeps all 4 pieces consistent, which helps when replacing multiple matching parts in one service session. The metal build adds the firm, precise shape needed for hardware that sits within moving chassis areas and must hold its position once installed. For workshop organisation, the pack also makes sense as a ready reserve for future wear-related replacement. On a bench setup, these pins fit naturally into routine repair jobs, partial rebuilds or the refresh of a frequently used DT-03 chassis. They also suit planned maintenance before the next running session, when matching hardware dimensions can save time and keep a build mechanically consistent.
Screws & ball head screws
DT-03 5mm Ball Connector, Servo Saver Part
319804154€4.39
The DT-03 5 mm Ball Connector M2 for the servo saver is a small RC spare part built around a clear mechanical job: creating the pivot point where a linkage can snap or seat onto a rounded ball head and move through the steering action. Its compact shape combines a smooth 5 mm ball, a narrow collar and an M2 threaded post for screw-in installation in the matching assembly. This format suits DT-03 setups that use a servo saver connection with this size and thread specification. The spherical head gives the linkage a consistent contact point, while the threaded shaft anchors the part in place inside the steering hardware. As a replacement component, it helps restore the original connection geometry when an existing ball connector is worn, damaged or missing. The black finish and metal build match the technical look of RC running gear and fit neatly into confined spaces around steering parts. On the bench, this connector belongs in routine maintenance, rebuilds and parts replacement for compatible DT-03 assemblies. It is especially useful when refreshing steering response after wear at a frequently moving joint, or when completing a repair with the correct 5 mm and M2 specification rather than a near match.
Shock absorbers & springs
DT-03 C Parts, chassis damper stays spare set
319000626€16.49
DT-03 C Parts provide replacement chassis and damper stay sections for selected RC model builds, with the main components supplied on a grey injection-moulded sprue for clear identification before removal. The set is intended for maintenance work, rebuilds and parts replacement where the original mounting sections need a direct-format spare. The sprue layout groups multiple structural pieces in one frame, including the chassis and damper stay elements named in the product data. That format helps keep the parts together during storage and bench work until each section is cut free for installation. The moulded construction suits the precise shapes needed around mounting points and connected assemblies. Compatibility is stated for 47347, 47371, 57872, 57895, 58587, 58628 and 84435, which gives a clear reference for matching this spare set to the correct vehicle platforms. On the workbench, this set fits naturally into routine service jobs after wear, damage or a full strip-down of the model. It also works as a practical stock spare for hobby rooms where frequently used chassis sections are kept ready for the next repair session. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
DT-03 CVA Damper Set Short/Mini RC Chassis Parts
300054567€33.99
The DT-03 CVA Damper Set Short/Mini brings oil-filled suspension action to a range of Tamiya off-road chassis cars, replacing basic friction-style movement with a more refined damper setup. With 2 mini shock units and 2 short shock units, the set equips 1 complete chassis and gives front and rear suspension the controlled compression and rebound needed for cleaner handling on loose ground and uneven sections. Inside the set are the parts for 4 assembled dampers, including damper bodies, piston rods, springs, seals and hardware. During assembly, oil is added to each cylinder and the piston is moved slowly to release trapped air before the cap is tightened, creating the internal damping effect that defines the CVA design. Separate front and rear assemblies use different parts and oil seals, and spring spacers are fitted to adjust preload after the springs are installed. The dampers mount to the chassis in the same way as the standard kit units, so the upgrade stays focused on suspension behavior rather than a change in layout. Compatibility covers DT-03, DT-03T, DT-02, TT-02B and DF-02 chassis cars, which makes the set useful for repair, replacement or tuning across several established platforms. On a buggy or off-road build, that means a more settled response through bumps, jumps and rough sections where suspension consistency shapes how the chassis tracks and lands. Warning! Not suitable for children under 14 years.
RC spare parts
DT-03 E Parts Upper Arm, RC spare part set
310004255€6.49
The DT-03 E Parts Upper Arm set supplies the suspension pieces needed when a DT-03 chassis calls for a direct replacement. Each molded arm remains attached to the black runner, making the parts easy to identify before trimming and fitting into the existing assembly. The set contains 2 mirrored upper arm components in a 1+1 configuration, shaped for opposite sides of the suspension. Hinge mounting points are molded at both ends of each arm, and the elongated profile includes open reinforcement sections that match the original part layout. The visible E marking on the sprue helps confirm the correct section during a rebuild or when sorting spares at the workbench. As a dedicated RC spare part set, this pack focuses on the exact chassis area that takes repeated movement during running sessions and service intervals. It fits naturally into repair tasks after wear, damage or a full strip-down of the suspension assembly. Kept in a spares box, the fresh molded parts are ready for planned maintenance or for bringing a DT-03 build back to its intended suspension geometry with matching left and right arm pieces.
Axes & drive shafts
DT-04 B Parts Uprights, chassis spare parts
300051755€8.99
The DT-04 B Parts Uprights set brings together molded replacement components for the new DT-04 chassis, making it easier to restore worn mounting points or replace damaged running gear with matching parts. Black resin pieces for the front and rear sections keep the fit aligned with the original chassis layout, whether the workbench task is a targeted repair or a broader rebuild. Beyond the uprights, the set covers several key connection areas of the chassis. C-hubs support the front end structure, while damper stays provide the shock mounting sections used in the suspension setup. The steering linkage transfers servo movement through the steering assembly, and the servo horn forms the connection point between servo output and linkage movement. Hex hubs complete the wheel mounting area, so the set reaches across several mechanical zones instead of covering only one isolated part. This parts group suits maintenance sessions after heavy running, rebuilds of a used chassis, or keeping workshop stock ready for future repairs. It also helps when a fresh DT-04 build needs replacement pieces on hand for the steering, suspension and hub areas most likely to see regular service. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
DT-04 Carbon Damper Stay Set, RC tuning parts
300022094€29.79
The DT-04 Carbon Damper Stay Set adds a focused suspension upgrade to a DT-04 RC chassis with carbon fiber plates and dedicated mounting hardware. Multiple holes in the main stay and side plates create clear adjustment options for damper positions, supporting setup changes that suit different surfaces and driving styles. The set contains 1 long carbon fiber plate, 2 smaller support plates, 4 black ball studs, several screws in different lengths, 2 lock nuts with blue nylon inserts, and 2 metal washers. This combination forms a complete fitting set for the stay components rather than loose replacement pieces gathered from different packs. The carbon fiber construction keeps the parts thin and rigid, while the hole pattern allows measured changes to mounting locations. Ball studs and lock nuts support secure attachment at the specified points, and the washers help seat the hardware cleanly during installation. On a workbench, the parts layout is easy to sort before fitting, and on the chassis the stay set supports careful suspension tuning through hardware-backed position changes. It suits builders refining a DT-04 setup with a dedicated carbon fiber upgrade rather than a general cosmetic add-on. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
DT-04 Chassis blk, RC chassis part, black tub
319335912€12.79
DT-04 Chassis blk provides the core lower frame for an RC model build, with a black molded tub shape that brings the main structure together in one substantial component. Raised sidewalls, integrated screw posts and a ribbed interior create a clear base for positioning major assemblies while keeping the layout defined on the bench. The molded underside geometry shows how this chassis part is designed to carry more than a flat floor alone. Reinforcing ribs run through the interior to stiffen the form, while circular holes and mounting points are placed directly into the tub for mechanical fastening. The extended end plate section adds another structured area with several fixing holes and ribbed supports, giving the build extra attachment space where connected assemblies need a stable anchor. As a replacement or project part, this chassis tub restores the original lower structure without changing the designated DT-04 layout. On a rebuild, repair or fresh parts-based assembly, this component sets the position for the rest of the chassis around a single molded base. The black finish matches the functional look of an RC underframe, and the one-piece construction keeps the mounting geometry together in the form intended for the DT-04 platform. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
DT-04 Full Ball Bearing Set, chassis accessory
300022092€24.29
The DT-04 Full Ball Bearing Set adds a precise drivetrain and steering upgrade to the DT-04 chassis with 18 metal bearings in 3 sizes. Installed in rotating points across the chassis, the bearings replace plain support parts with rolling contact, which helps moving assemblies turn with less drag and a smoother mechanical feel. The set includes 4x 850, 4x 1050 and 10x 1150 bearings, matching the different mounting points used in the DT-04 layout. That size spread makes the set suitable for a complete bearing conversion rather than a partial refresh of only one section. In the drivetrain, freer rotation supports more efficient transfer of motor output through the transmission. In the steering system, the same bearing construction helps linked parts move with a more direct action at the front end. This chassis accessory suits a new DT-04 build as well as later workshop maintenance when worn parts are being replaced. The small, shielded metal bearings are arranged as a dedicated fitment set for the platform, making them a practical choice when the goal is a cleaner-running buggy with reduced mechanical resistance in its key moving assemblies. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
DT-04 M Parts, chassis mount spare parts
319115594€11.49
The DT-04 M Parts gearbox and chassis mount set provides replacement components for RC model maintenance where structural sections need to be renewed. Supplied as black injection-moulded parts on sprues, the set is arranged for clear identification before trimming, sorting and installation. The visible parts tree contains multiple connected components shaped for functional mounting and support roles, including chassis-related sections, bracket forms and frame elements. This format helps keep small pieces together until they are needed at the bench and allows each part to be checked against the original assembly before removal from the runner. The moulded layout is suited to repair work after wear or damage, and it also supports planned rebuilds where a fresh gearbox or chassis mounting section is required. The technical presentation keeps the focus on fit, structure and correct part selection. On a workbench, the sprue format makes it easier to compare each section with the existing RC vehicle before cutting and fitting. During servicing, the set can be used to replace damaged mounting areas, refresh key structural points or prepare a stored chassis for reassembly with the correct DT-04 M components. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
E-Ring Set, model accessory, 17 pcs 2mm 3mm 4mm
300050380€2.99
This E-Ring Set brings small but essential fastening hardware into model assembly with 17 dark metal retaining clips in 3 sizes: 2 mm, 3 mm and 4 mm. Each E-ring is shaped to snap onto a matching groove on a shaft, axle, rod or pin, where it holds a mounted part in position while keeping the fixing compact and mechanical. The size spread makes the set useful across different fixing points instead of limiting the bench to a single diameter. In practical use, an E-ring is pressed onto the grooved end of a metal part so the open side clips over the shaft and the ring seats into place. That mechanism suits wheel mounts, axle retainers and other small moving assemblies where a screw or nut would take more space. The dark metal finish matches the function-focused character of workshop spares and replacement hardware. Kept in a parts box, drawer insert or service tray, the set supports routine maintenance as well as the recovery of lost clips during rebuilds. The stated scope of delivery is 1 set with 17 E-rings, giving a ready stock of common small retainers for model work that depends on secure, correctly sized mechanical fastening. Warning! Not suitable for children under 14 years.
Gears & motor pinions
F Diff. Joint L & R, model spare parts for 58370
309808059€20.99
F Diff. Joint L & R for 58370 supplies 2 dedicated spare parts for the front differential area, with one left and one right version matched to the named model reference. The black molded pieces show a technical, component-led form with flanged heads and split forked ends that suit connection points in a mechanical assembly. As model spare parts, these joints are intended for targeted maintenance rather than general upgrading. The paired L and R layout matters where the front drivetrain uses side-specific geometry, allowing the correct part to sit in the correct position instead of forcing a universal substitute. The visible shape of each piece supports that role: the cylindrical body forms the main connection section, while the forked end is made to interface with adjoining moving parts in the assembly. This keeps the focus on fit, alignment and restoring the original mechanical layout of 58370. On the workbench, the set suits planned servicing, replacement of worn front differential components, or completion of an existing build that needs the specified joints. The 2-part format keeps both sides of the front assembly covered in one pack, making it easier to match left and right positions during installation. Warning! Not suitable for children under 14 years.
Gears & motor pinions
F101-F104 G-Parts Spur Gear Set, RC spare parts
300050506€10.29
The F101-F104 G-Parts Spur Gear M0.6/63Z set is a drivetrain spare-parts pack for selected RC chassis, centered on a 63-tooth main gear with module 0.6 gearing. It gives a direct replacement route for wear parts in the transmission area and keeps compatible running gear ready for service sessions, rebuilds and routine maintenance. The set is specified for F104PRO II, F104W, F104 and F103GT chassis. For the F104PRO II chassis, the data states that only the 63T06 spur gear is used. Scope of delivery contains 1x G-Parts tree with 7 pieces, grouping the gear and related molded components in one pack for organized parts handling at the bench. The black molded parts shown in the set include the large spur gear and smaller matching pieces shaped for mounting and spacing within the assembly. This spare-parts set suits drivetrain refresh work after regular use, replacement during a rebuild, or keeping key transmission components on hand between running sessions. In a workshop setup, the defined chassis compatibility and exact 63-tooth specification make it easier to match the correct gear set before installation. Warning! Not suitable for children under 14 years.
Axes & drive shafts
F103 Turnbuckle Tie Rod Set, RC spare parts
300053150€14.99
The F103 Turnbuckle Tie Rod Set brings adjustable linkage hardware to the F103GT chassis in a compact 20-piece spare parts pack. At the center are 2 turnbuckle shafts in 3 x 42 mm size, built to create a tunable connection within the steering or rod linkage layout. A reverse screw on 1 side of each shaft allows the rod length to be changed by turning the shaft itself, which helps when alignment needs fine correction during maintenance or reassembly. Alongside the shafts, the set provides 6 adjusters and 4 cushion balls in 5 mm size, plus the related small hardware for mounting and connection. This combination supports the pivoting and threaded joints used in RC chassis linkages, where clean fit and measured adjustment matter more than fixed-length parts. The included parts are suited to replacing worn linkage components or restoring a chassis with matching hardware dimensions already specified in the set. On the bench, the set fits naturally into steering service, linkage renewal or a parts refresh for an F103GT build. The compact format also makes it useful to keep with workshop spares, so the required rods, adjusters and joint hardware are ready when a setup change or replacement is needed. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
F103RS/GT-F104 Front Spring (3x4), model spare part
300050509€5.59
The F103RS/GT-F104 Front Spring (3x4) is a model spare part for front suspension service on a wide range of compatible Tamiya chassis. With 12 coil springs in the pack, it supports routine replacement work as well as keeping matching spares ready for setup changes between running sessions. This set is specified for F103RS/GT-F104 applications and is listed for F104PRO II, F104Ver.II PRO, F104W, F104, F103GT, RM-01, TRF103, TRF102 and TRF101. That broad compatibility makes it useful for hobby benches that support more than one chassis generation. The 3x4 spring format gives a clear reference point when replacing existing front suspension parts, helping maintain the intended configuration on the car. As a dedicated spare part rather than a general hardware assortment, it keeps maintenance focused on the exact area that needs attention. On a workshop bench, the 12-piece quantity is practical for regular upkeep, rebuilds and storing reserve parts alongside a race or practice setup. It also suits builders who maintain several compatible chassis and want one spring pack that can stay in rotation across different models. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
F104 Disc Ball Set, chassis spare part, 3 mm
300051347€5.69
The F104 Disc Ball Set is a dedicated spare part for ball differential maintenance on compatible F104 series chassis. With 8 steel balls and matching pressure plates in a 3 mm format, it supplies the key contact parts used in the differential assembly and keeps replacement focused on the stated drivetrain area. Compatibility is specified for F104PRO II chassis, F104W chassis, F104 chassis and F103GT chassis. The steel construction suits the repeated contact points inside a ball differential, where smooth, consistent interaction between the balls and plates is central to the mechanism. Instead of a broad assortment of unrelated workshop parts, this set stays specific to one service task and one family of chassis. The scope of delivery contains 1 balls and pressure plate set. On the workbench, that clear compatibility helps when preparing a planned refresh of an existing F104 drivetrain or keeping matching spare parts ready between running sessions. In a parts box for formula chassis maintenance, the 3 mm specification gives a direct reference for selecting the correct replacement set for the listed platforms. Warning! Not suitable for children under 14 years.
Axes & drive shafts
F104/F103 Special King Pin, model spare part
300053119€4.49
The F104/F103 Special King Pin is a dedicated spare part for compatible F104 and F103 chassis, intended for maintenance, repair and ongoing setup work. As a king pin, it belongs to the front suspension area where precise alignment between steering and suspension components matters during rebuilds and replacement work. This part is supplied for the F104/F103 platform rather than as a generic hardware piece, which helps keep servicing focused on the correct chassis family. It suits replacing a worn or damaged king pin during routine maintenance, or keeping a matching spare ready in workshop storage for future repairs. The compact format also fits neatly into parts boxes and bench organisers used for model upkeep, making it easier to separate chassis-specific hardware from general screws and fittings. On the workbench, the part supports clean, direct replacement when a front-end rebuild is needed after running sessions or inspection. It also fits tuning and restoration tasks where the original suspension layout of an F104 or F103 chassis needs the correct replacement component rather than an improvised substitute. Warning! Not suitable for children under 14 years.
RC spare parts
FF-03 Pinion Gear 28/29T, RC spare gear set
300054229€16.29
The FF-03 Pinion Gear 28/29T M0.6 set adds a focused drivetrain tuning option for compatible RC chassis. Aluminum construction, a fluorine lubricating coating and a newly developed rounded tooth tip shape work together at the gear mesh to reduce friction losses and noise while supporting cleaner power delivery. The set provides 28T and 29T pinion options in module 0.6, making it useful when gearing needs to be adjusted for different running conditions or chassis setups. The rounded tooth profile changes how the teeth meet under load, which helps the drivetrain engage more smoothly as the motor turns through the spur gear. Compatibility covers a broad range of platforms including FF-04 EVO, FF-03, FF-03 PRO, TA08 PRO, TA07 MS, TA07 PRO, TA06 MS, TA06, TA06 PRO, TB-Evo.7, TB-Evo.6 MS, TB-Evo.6, TB-04, TC-01, TT-02RR, TT-02D, TT-02, XV-02PRO, XV-01 and XV-01 PRO. For TA07 MS chassis, use with 51356, 51423 and 51548. For TT-02, TT-02D and TT-02RR chassis, use with 54500. This gear set suits bench tuning before a run as well as drivetrain updates during regular maintenance. It also fits neatly into a spares box for racers and builders who keep multiple compatible chassis in rotation. Warning! Not suitable for children under 14 years.
Gears & motor pinions
FF-03 Spur Gear 68T M0.6, RC spare part
300051423€4.59
This spur gear brings a defined 68T tooth count and M0.6 pitch to compatible RC chassis, giving the drivetrain a concrete replacement part for service, repair and setup work. As a single main gear, it suits bench maintenance where a worn transmission component needs to be swapped for the correct specification. The part is listed for FF-03 chassis and FF-04 EVO chassis, and it also covers a broad compatibility range across TD4, TD2, TA06, TA06 MS, TA06 PRO, TA07 PRO, TA08 PRO, TT-02, TT-02 TYPE-S, TT-02 TYPE-SR, TT-02D, TT-02RR, XV-02PRO, XV-01, XV-01 PRO and XV-01T chassis. That spread makes it relevant for racers and builders managing several platforms within one workshop. On TT-02 based cars, use can also apply to vehicles equipped with 54500. For TT-02RR chassis, the gear is listed as kit standard equipment. In practical use, this is the kind of transmission part kept on hand for routine rebuilds, drivetrain refreshes and chassis-specific parts planning. The single-piece scope of delivery keeps the replacement straightforward when preparing a compatible touring, front-wheel-drive or rally platform for the next maintenance session. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Flanged Tube, model accessory, 4.5 x 3.5 mm
309804382€4.49
This flanged tube is a small model accessory specified at 4.5 x 3.5 mm and listed with detailed dimensions of 3.1 x 4.5 x 4.0 mm. The flanged form helps distinguish the part from a plain tube when a build or repair calls for a defined edge and a precise seated position within an assembly. The pack contains 2 matching pieces, which suits jobs that need a pair of identical fittings rather than mixed hardware. In model maintenance, exact measurements matter, and the stated 3.1 mm, 4.5 mm and 4.0 mm figures give a clear reference when checking parts against an existing setup. The compact format makes this accessory relevant for detailed replacement work, careful restoration, or keeping spare hardware ready for future servicing. On the workbench, a correctly sized flanged tube can save time during part selection because the specification is already narrowed to a defined format. For ongoing model upkeep, 2 identical tubes also make it easier to complete symmetrical mounting points or store a matched spare set alongside other small workshop parts. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Flanged Tube, model accessory, 4.5 x 3.5 mm
309808021€3.09
This flanged tube set is a small but specific model accessory for repair, maintenance and parts matching. The pack contains 2 pieces, and the stated 4.5 x 3.5 mm format gives a clear reference point when an existing assembly calls for the same size and flanged construction. The source data also lists the dimensional specification as 3.1(4.5) x 3.5(4.0) mm, which adds another concrete identifier for checking fit against a current build or replacement need. A flanged tube is typically chosen for its defined shoulder and seating position within a mechanism, so the named form matters as much as the measurement when selecting the correct hardware. In a workshop drawer, this kind of small component helps keep repair jobs moving without substituting an unmatched part. Used during model upkeep, rebuilds or careful parts sorting, the 2-piece set supports direct replacement where the same tube is needed again. It also works as a practical stock addition for builders who keep commonly used hardware sizes on hand for future service tasks. Warning! Not suitable for children under 14 years.
Spare parts for old cars
Frog 2005 Wheel Adapter Set for Reissue Buggies
300053913€18.29
This wheel adapter set is made for reissue buggy conversions where wheel choice matters. The hexagonal aluminium adapters allow The Frog 2005 and other specified chassis to use off-road tyres and wheels sold separately, changing the wheel mounting format for a wider range of buggy setups. The set contains 2 aluminium wheel adapters, 2 4 mm flange lock nuts and 2 stainless steel 2 x 10 mm shafts. Those parts form a compact hardware package for the wheel mounting area, with the shafts passing through the adapter and the lock nuts securing the assembly in place. The machined aluminium construction gives the adapters a clean, technical finish, while the stainless steel shafts add the matching metal hardware needed for the conversion. Compatibility is stated for chassis 58354 The Frog 2005, 58346 Hornet 2004, 58346 Grasshopper 2005, 57746 XB Grasshopper and 57741 XB Hornet. Used on a reissue buggy build, the set supports a switch to separately sold off-road wheel and tyre combinations that suit the chosen look or running surface. It also fits restoration work on older chassis where the original wheel format is being updated with compatible buggy wheels. Warning! Not suitable for children under 14 years.
Spare parts for old cars
Front Upright Set F-103/Grasshopper II
300050395€11.39
The Front Upright Set F-103/Grasshopper II is a chassis parts set for RC model maintenance, centered on the front steering area where precise fit matters most. With 21 pieces in the scope of delivery, the set provides the core hardware needed to replace worn front upright parts and restore the intended steering layout on supported Formula platforms. Compatibility covers F104PRO II, F104Ver.II PRO, F104W, F104 and TRF103, which makes this set useful across several established chassis generations. For TRF102 chassis and TRF101 chassis, the data specifies adjustment with 53585 shim, so the installation can be matched to those layouts as required. The included parts are intended for front-end assembly work rather than general chassis use, which keeps the application clear when servicing a car after running sessions or preparing a fresh build. On the bench, this set suits routine replacement of front upright components, careful steering rebuilds and targeted setup work around the axle carriers and related mounting points. It also fits the needs of hobbyists who keep multiple compatible Formula chassis in service and want the correct front suspension and steering parts ready for maintenance. Warning! Not suitable for children under 14 years.
Axes & drive shafts
Front Upright Set, model spare parts, MB10/11
319808262€18.49
This front upright set supplies 2 matching metal parts for MB10/11, with left and right versions shaped as a mirrored pair for front-end replacement work. The silver finish and compact machined form give each piece a clean mechanical look, while the curved arm and pivot section point to a defined mounting role within the assembly. Each upright shows a circular attachment hole at one end and a rounded housing at the other, creating the connection points needed for a controlled mechanical fit. A vertical cylindrical shaft extends from each part and ends in a threaded screw tip, adding a fastening detail that supports installation into the intended front assembly position. One housing appears to carry internal threading, indicating that the two sides are not interchangeable and are made for their specific left or right placement. This set suits repair, maintenance or parts replacement on a compatible MB10/11 model where worn or missing front hardware needs a like-for-like component shape. Kept as workshop spares or fitted during a rebuild, the pair provides the dedicated geometry needed for accurate front-end restoration. Warning! Not suitable for children under 14 years.
Axes & drive shafts
Front Upright Set, RC spare part for Tamiya chassis
300051352€6.19
This front upright set supplies 2 steering knuckles for the front axle of compatible RC chassis, giving the steering assembly the exact mirrored left and right parts needed for repair or routine maintenance. The shape with circular axle openings and multiple mounting points supports correct integration into the front suspension area, where precise alignment matters for wheel guidance and steering movement. The set is listed for a wide range of chassis platforms: FF-04 EVO, FF-03, FF-03 PRO, TA07 MS, TA07 PRO, TA06 MS, TA06, TA06 PRO, TA05 Ver. II, TB-Evo.6 MS, TB-Evo.6, TB-05 PRO, TB-04, TB-04 PRO, TB-03, TB-03 VDS and TT-02 TYPE-S. That broad compatibility makes this pair useful for keeping several touring car and front-wheel-drive builds in running condition with one clearly matched spare. The scope of delivery contains 2 front steering knuckles from C-Parts TB-03. In workshop use, this pair suits worn, damaged or missing front uprights on supported chassis and helps return the front end to its intended mounting layout. It also serves as a practical stock spare for regular service between driving sessions, especially on platforms that share steering and suspension hardware. Warning! Not suitable for children under 14 years.
Gears & motor pinions
Gear Bag for 58340, model spare gear set
309335432€7.19
This gear bag for 58340 brings the drivetrain back into service with 4 replacement parts shaped for geared power transfer. The set contains white injection-moulded components shown as 2 large gears, 1 smaller double pinion gear and 1 circular cover plate with 3 mounting holes, giving the gearbox area the core parts needed for a targeted repair. The larger gear with a raised cylindrical hub works alongside the second large toothed gear, while the smaller double pinion links motion between stages of the transmission. That layout points to reduction and transfer inside the gearbox rather than cosmetic trim, so the set is suited to maintenance where worn teeth, missing internals or damaged drive parts interrupt movement. The separate cover plate closes the assembly at the matching mounting points and helps return the parts to their intended position inside the housing. Used during a rebuild, service interval or parts replacement, this set supports focused work on the transmission section of 58340 without replacing unrelated assemblies. It also fits neatly into a spares collection for model maintenance, where keeping the correct gears on hand can shorten downtime between bench work and the next run. Warning! Not suitable for children under 14 years.
Axes & drive shafts
Gear Box Joint, replacement part for 43520
309804237€8.99
The Gear Box Joint set for 43520 supplies 2 matching replacement parts for a drivetrain connection point where accurate fit matters. The machined metal finish and compact cylindrical form suit technical model maintenance, helping restore a clean mechanical link in the gearbox area when an original joint is worn, damaged or missing. Each joint is shaped as a dedicated spare for use with model number 43520 rather than as a generic workshop component. The 2-piece format provides a matched pair for repair planning and parts storage, which is useful when both sides of a mechanism need the same connection standard. The metal construction supports a precise seating surface at the contact point, which matters in assemblies where connected parts need to meet cleanly. As a small drivetrain component, this set fits naturally into regular service work on running models and mechanical rebuilds. On the workbench, the pair can be kept ready for scheduled maintenance or used to replace a failed connection during a repair session. For model builders who maintain existing vehicles over time, dedicated spare parts like these help keep compatible assemblies operating with the intended hardware. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Gear Differential Putty, tuning accessory, 25 g
300042247€8.29
Gear Differential Putty is a tuning accessory for transmission differentials in model vehicles, supplied as 25 g in a plastic case. By controlling the differential action, it creates an effect close to direct coupling, changing how the drivetrain responds when load builds through the driven wheels. The putty is applied as a physical insert rather than a mechanical replacement part. The rolled material is cut with scissors, formed to about 3 mm in diameter, and then packed into the transmission differential. This gives a clear, hands-on way to adjust internal resistance with small portions instead of replacing the whole differential assembly. The method suits fine setup changes, because the amount and shape of the putty can be prepared before installation. The supplied case keeps the material contained between workshop sessions. Under heavy load from the road surface, the transmission moves to help avoid damage to the drive system, so the tuning effect is paired with protective drivetrain behavior. This makes the putty useful for setup work on model vehicles where differential response has a direct influence on handling and power delivery during running sessions. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Gearbox B Parts, RC spare parts for M.Pumkin
300005276€19.29
This B Parts gearbox set is made for M.Pumkin and Lunch Box and provides the molded components needed for work on the transmission housing area. The black sprue carries matched structural pieces that suit replacement, restoration, or a fresh rebuild when worn or damaged gearbox sections need to be exchanged. The visible layout shows 2 mirrored casing halves, a central round cover piece, and 2 smaller circular discs, all molded as a coordinated parts tree. That arrangement helps keep related components together before removal and gives a clear overview of the shapes used in the assembly. The larger shells feature cylindrical tower forms and ribbed circular housing details, indicating their role as enclosing and supporting mechanical internals. Because this is a model spare-parts set, it is intended for an existing compatible vehicle rather than as a standalone build. On the bench, this set supports focused repair work on the gearbox section of the compatible RC model. It also suits keeping a replacement sprue on hand for maintenance, especially where a rebuild calls for matching housing geometry instead of improvised substitutes.
Shock absorbers & springs
GF-01 Alu. Oil Damper (4), RC damper set
300054670€62.49
The GF-01 Alu. Oil Damper set adds 4 aluminum oil dampers to GF-01 and WR-02 chassis cars, bringing more controlled suspension movement to rough ground and uneven running surfaces. Silver-finish cylinders with blue anodized caps and ends give the chassis a crisp mechanical look while introducing a functional oil-filled damping setup. The set is supplied as an aluminum oil pressure shock absorber set with 99 pieces, including the small attachment parts needed for mounting. The assembly documents show 3-hole pistons, damper shafts, rod guides, O-rings, spacers and ball connectors working together inside each cylinder to manage suspension travel. Front and rear damper builds differ by chassis position, with 2 dampers configured for the front and 2 for the rear. The included damper oil is specified as #400 in the assembly notes. Use with spring kit 53974 is stated in the data, and G6-01 or G6-01TR chassis require 6 dampers where that setup is used. Installed on a GF-01 or WR-02 model, the dampers support more composed running when the chassis crosses loose ground, bumps and broken surfaces. The color-contrasting hardware also stands out during workshop assembly and suspension tuning, where each cylinder, cap and end remains easy to identify at a glance. Warning! Not suitable for children under 14 years.
Axes & drive shafts
GF-01 Full Ball Bearing Set, chassis accessory
300054924€39.99
The GF-01 Full Ball Bearing Set is a chassis accessory made to give GF-01 models a complete bearing upgrade with the exact quantities needed in one pack. The set contains 24 x 1150 ball bearings and 2 x 850 ball bearings, replacing the standard bearing arrangement at the rotating points across the chassis. By swapping in ball bearings for the kit standard plastic and metal bearings, the running gear can turn with less drag and a more consistent mechanical feel. The different bearing sizes cover the positions required by the GF-01 layout, so the set is built around the chassis rather than a generic assortment of parts. The compact metal components suit maintenance work, rebuilds and planned performance upgrades where efficient rotation matters. On the bench, the set supports a straightforward refresh of a used GF-01 runner or a more refined specification for a fresh chassis build. Once fitted, the smoother movement through the rotating assemblies helps the model make cleaner use of its available power during regular driving sessions.
Spare parts for old cars
Grasshopper Hornet chassis, RC spare part, black
310335050€12.69
This black chassis part for Grasshopper and Hornet models restores the central structure that carries the main assemblies of the vehicle. The moulded tub-style form combines side walls, mounting posts, screw holes and slots in one component, creating the defined base needed when a worn or damaged frame has to be replaced. Raised supports and cross braces are built into the moulding, so matching parts can be positioned against the chassis geometry already formed into the piece. The front and rear sections show reinforced mounting areas with several connection points for attaching the surrounding assemblies. That layout matters during repair work because the chassis is the reference part that determines how the rest of the model sits and aligns. The black finish matches the part designation, while the one-piece construction keeps the replacement focused on the core frame rather than a collection of separate brackets. Used in a restoration, rebuild or maintenance project, this spare chassis gives Grasshopper and Hornet models the correct base for reassembly. It suits workshop tasks where the original frame has cracked, worn at the mounting points or needs to be exchanged during a longer-running RC model refresh.
Gears & motor pinions
Hard Joint Cup-Set Gear Differential Spare Part
300053218€14.99
This spare part set combines a differential output with a hardened cone differential for gear differential service on compatible model vehicles. The pairing suits focused drivetrain maintenance where the differential assembly needs renewal with the two named components supplied together. The hardened cone differential is the key technical element in the set, adding a wear-oriented replacement part for rebuilds and repair work. In a gear differential, this component supports the transfer of drive through the transmission while the differential output forms the matching connection point within the assembly. The scope of delivery is clearly defined as 1 differential output and 1 hardened cone differential, which helps when planning a direct replacement around the existing drivetrain layout. The set is intended as an accessory and replacement component rather than a complete model. On the workbench, this combination fits routine servicing, repair after drivetrain wear, or preparation of a compatible chassis for further running. It also suits parts storage for model maintenance, where a clearly specified differential set can be kept ready for the next rebuild. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Hi-Torque Servo Saver Black, RC spare part
300051000€17.99
Hi-Torque Servo Saver Black brings a focused steering upgrade or replacement part to RC chassis work, with a 26-piece set that combines black molded components and metal hardware in one servo saver assembly. Built for the MF-01X chassis, it gives the steering system the dedicated parts needed where controlled force transfer and linkage connection matter during running and maintenance. The set contains the servo saver itself together with screws, nuts, washers, retaining rings and threaded ball studs. Those ball studs create the mounting points for linked steering rods, while the retaining rings secure the relevant rotating or stacked parts within the assembly. Combined use with 54120 is specified in the data, which matters when matching the setup to the intended chassis configuration. The black finish keeps the installed assembly visually consistent with surrounding chassis parts, and the grouped hardware avoids piecing together separate fasteners for this specific mechanism. On the bench, this spare part suits routine servicing, parts replacement or a fresh chassis build centered on the MF-01X platform. It fits naturally into steering work where worn saver parts, missing hardware or a chassis-specific installation calls for the correct component set rather than a generic substitute. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Hi-Torque Servo Saver, 1:10 accessory, white
300050473€17.29
The Hi-Torque Servo Saver in white is a steering accessory for RC model setups that need a precise, compatible linkage part. Designed for all Tamiya chassis and many 1:10 models, it supports cleaner steering response while improving return after direction changes, making it useful for fresh builds, maintenance work and replacement installs. The set combines white molded components with the small hardware needed to mount and connect the assembly, including screws, nuts, washers, retaining rings and ball-ended linkage parts. Those ball-joint style connectors support the steering linkage where controlled movement and secure attachment matter, while the retaining rings and fasteners complete the mechanical fit. For MF-01X chassis, combined use with 54120 is specified, which helps align the part choice with that chassis configuration. On a workshop bench, this servo saver suits routine servicing as well as targeted steering updates on compatible 1:10 RC cars. It also works as a useful spare for keeping an existing chassis ready when worn steering parts need to be replaced with matching hardware and mounting pieces. Warning! Not suitable for children under 14 years.
Spare parts for old cars
Hornet Clamp Aluminum Wheel Hubs 2-Piece Set
300022043€28.29
This 2-piece set of clamp-type aluminum wheel hubs is designed as a focused upgrade for classic Tamiya off-road models, replacing the kit-standard B5 parts with a more rigid wheel connection. Each hub clamps onto the wheel axle instead of relying on a simpler fit, which helps keep wheel attachment precise and supports smoother rotation while the model is running. The set includes 2 aluminum wheel hubs and screws for attachment, keeping the mounting hardware aligned with the upgrade itself. A blue anodized finish gives the hubs a clear visual contrast at the wheel area, adding a technical accent that stands out during assembly and once the model is on display. The clamp construction is the key mechanical difference here: tightening the hub onto the axle creates a firmer interface between axle and wheel, which is especially useful where accurate wheel seating matters. Compatibility is stated for the Hornet, Frog, Lunch Box, Monster Beetle, Grasshopper, Subaru Brat and Fast Attack Vehicle. That makes the set a practical choice for restoring, refining or visually updating several well-known chassis in one parts family. On a bench build or a running model, the hubs bring together precise attachment, aluminum construction and a distinctive blue finish in one compact upgrade. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
J Parts Fr. Damper Stay, model spare parts set
319115433€14.79
J Parts Fr. Damper Stay is a dedicated spare parts set for the 58618 Mt.Beetle and focuses on the front damper mounting section used in the chassis structure. The molded black components are supplied on a sprue frame, giving a clear overview of the shapes before cutting, test fitting and installation during a repair session. The set is suited to replacing worn, damaged or missing structural parts rather than improvising with unmatched hardware. Multiple mounting pieces and braces are formed as matching components, which helps maintain the intended geometry around the front suspension area. The sprue layout also helps with part identification at the bench, especially when several maintenance jobs are underway at once. Because this is a model spare parts set rather than a complete vehicle or kit, it fits naturally into regular workshop use alongside stored service parts for ongoing upkeep. On the work surface, the parts support a focused rebuild of the front end after heavy running or accidental damage. They also make sense as reserve stock for a 58618 Mt.Beetle build that is driven regularly and maintained over time, where having the correct front damper stay parts ready can shorten downtime between sessions. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
J-Parts for Subaru Impreza WRC'08, model parts
309115244€14.19
This J-Parts set is made for the Subaru Impreza WRC'08 from kit 58426 and serves as a dedicated replacement parts option for that exact model. The defined J-Parts designation helps identify the correct section within the original build, which is useful when an existing model needs a missing or worn component replaced rather than improvised with a non-matching part. Because the data names this set specifically for 58426, the fit reference is tied to that kit and to the Subaru Impreza WRC'08 body version listed here. That makes the set relevant for repair work, restoration of an older build, or keeping a previously assembled model in running or display condition with the intended parts group. As model supplies, these parts are aimed at maintaining an existing build rather than changing it into a different version. On the workbench, a dedicated replacement set like this can save time when sorting spares for a rebuild or when completing a model that is missing one defined parts section. It also gives collectors and builders a clear way to keep kit 58426 aligned with its original specification over repeated maintenance cycles. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Joint Boot BB21, spare part for Mt.Beetle
316255002€4.39
Joint Boot BB21 is a model spare part specified for the Tamiya 58618 Mt.Beetle. The long black component has a bellows-style form with several ribbed sections and thicker collar points, a shape used where a fitted cover needs to move with the linked assembly while keeping the area around the joint enclosed. The moulded one-piece construction gives the part a clean technical profile for maintenance, replacement or a faithful rebuild of the original model layout. Its accordion-like sections indicate controlled flexibility, allowing compression and extension as the connected mechanism moves. The stepped ends and central collars provide defined seating points that match the intended mounting position rather than acting as a generic sleeve. That makes BB21 useful when an existing boot is worn, split or missing and the assembly needs the correct designated part again. In workshop use, this spare part fits naturally into repair sessions focused on keeping a Mt.Beetle complete and mechanically tidy. It also suits stock-box planning for regular running models, where model-specific service parts help keep maintenance work straightforward and consistent with the original specification. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
Leaf Spring A (4), model spare part for 58372
309808091€14.49
Leaf Spring A is a dedicated model spare part set for 58372, supplied as 4 matching spring strips in black metal. Each strip has a curved profile, rolled looped ends and 3 round mounting holes near the centre, giving the set the exact component form needed where this part group is missing, worn or due for replacement. The 4-piece pack supports maintenance and rebuild work with a consistent set of identical parts rather than mixed hardware. The metal strips are shaped for suspension-style or retaining-style installation within the matching model assembly, and the repeated hole pattern helps align the part with the existing mounting points on 58372. This makes the set useful for restoring the original mechanical layout of the designated model instead of adapting a generic strip or bracket. The compact spare part format also suits keeping a correct replacement set on hand for workshop storage. On the bench, the set fits naturally into repair sessions, part swaps and planned overhauls of 58372. It also works as a direct stock replacement when a rebuild calls for the exact Leaf Spring A component rather than an improvised alternative.
Shock absorbers & springs
Leaf Spring B, spare part set for 58372
309808092€8.29
Leaf Spring B is a dedicated spare part set for 58372 and supplies 4 matching replacement pieces for repair or maintenance work on the designated model. The set uses one clearly defined component type, making it suitable when the original leaf spring elements need to be exchanged rather than replacing a larger assembly. Each piece follows the same curved form shown in the reference image, with 3 round mounting holes positioned near the centre for attachment. That repeated geometry matters during maintenance because all 4 parts share the same layout and can be fitted as matching replacements within the same suspension area. The black finish keeps the appearance consistent with the pictured parts, while the compact format suits parts storage in a workshop drawer, spares box or model case between repair sessions. As a model spare part, this set is aimed at restoring the intended structure of 58372 with the correct designated component rather than adapting a generic substitute. The 4-piece format supports planned servicing as well as single-part replacement when a matching spare is needed on hand. On the bench, the identical hole pattern and arched profile help keep repair work focused on the exact section that needs attention on 58372. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
Leaf Spring, spare part set, 2-piece suspension pair
309808177€5.99
This leaf spring set supplies 2 replacement suspension parts for compatible model maintenance and repair work. Each piece is formed as a curved metal spring strip, creating the arched profile needed for a leaf spring layout and giving a clear mechanical role within the assembly. At the center of each spring, 3 round mounting holes provide the fastening area for installation to the matching structure. The ends are bent into looped hooks in opposite orientations, showing that the parts are made as a left and right mirrored pair rather than 2 identical strips. That mirrored construction matters when restoring the original suspension geometry on both sides of a vehicle. The black finish and compact shape also make the parts easy to identify among workshop spares during servicing. The set suits rebuilds, repairs, and parts replacement on a compatible model that uses this spring format. Whether a suspension assembly is being refreshed after wear or a stored build is being returned to running condition, these 2 springs provide the specific hardware needed for the job. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
LED Stopper, model accessory, 2 pcs.
309005859€5.99
This LED Stopper set is a focused model accessory for detailed assembly work, supplied as 2 sprues with multiple molded stopper pieces ready to be removed and fitted as needed. The compact format keeps matching parts together on the runner, which helps maintain order while preparing small components at the bench. Each sprue is injection molded in ABS and marked with part identifiers, giving the set a clear technical character that suits precise hobby tasks. The forked stopper shapes shown on the runners support controlled placement in builds that call for small retaining parts. Because the pieces stay attached until needed, sorting and handling remain straightforward during preparation. The uniform molded layout also helps when checking parts before cutting them free. On the workbench, this set fits naturally into careful model sessions where small components and clean organization matter. It suits builders who want a dedicated supply of matching stopper pieces on hand for compatible projects and detail-focused assembly steps. Warning! Not suitable for children under 14 years.
Axes & drive shafts
Left Upright Front, RC spare part with ball stud
300445169€6.99
This front left upright is a dedicated spare part for the Stadium Blitzer and is intended to restore a specific suspension or steering connection point in the front corner assembly. The molded piece combines a compact arm shape with a central round mounting hole, creating the defined pivot location needed for the surrounding mechanism to sit correctly. A brass-colored ball stud at one end adds the articulated connection point for the linked assembly. The upright also carries a silver metal shaft with a threaded tip, which provides the fastening point for installation into the matching front section. Reinforced ribs in the molded body support the shape of the part around the mounting area, while the white finish makes the component easy to identify during maintenance or parts sorting. Supplied as 1 piece, it is specified as the front left version rather than a universal side-to-side replacement. This kind of spare part suits focused repairs after wear, damage or a missing original component in the Stadium Blitzer. Kept in a workshop drawer or parts box, it supports routine maintenance and helps return the front assembly to its intended mechanical layout with the correct left-side geometry. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
Low Friction Damper V Parts, RC spare parts
300053334€7.29
Low Friction Damper V Parts supply the small running components that keep RC damper assemblies working smoothly across a wide range of Tamiya chassis. The set contains 2 V-part sprues with 22 pieces and covers damper ends, top ends, spring retainers, resin pistons and resin damper spacers for low-friction, ultra-low-friction and TRF dampers. This spare parts set is aimed at rebuild work, scheduled maintenance and replacing worn suspension internals without changing the full damper assembly. The dark gray molded parts arrive on sprues for clean identification during bench work. Compatibility reaches across touring, formula, buggy and rally platforms named in the data, including XV-01, TA06, FF-03, TT-02, M-07 CONCEPT, M-08 CONCEPT, F104, DB01 and TD4 chassis. Several applications require combination with matching damper sets such as 53571, 42273, 42355, 42102, 42354, 53901, 53926 or 54993 as specified in the data. On a workshop bench, these components help restore precise damper movement after wear in the original running parts. They also make a practical stock addition for regular chassis servicing, especially where multiple compatible Tamiya platforms are already in use. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
Lunch Box D-Parts, replacement parts set
309005230€16.99
The Lunch Box D-Parts set is a dedicated replacement parts pack for 58063, supplying molded components on sprues for repair, restoration, or planned maintenance. Black injection-molded pieces with formed mounting shapes and structural contours support accurate replacement work while keeping the original model configuration intact. The sprue layout keeps the individual parts grouped until they are cut free, which helps with part identification during bench work and reduces mix-ups between similar small components. Visible shapes in the set include bracket-style sections, circular adapter-like pieces, connector forms, and a larger reinforced panel with raised ribbing. That mix points to structural and mounting functions rather than decorative trim, making the set useful when worn, broken, or missing components need to be exchanged with matching replacements. The molded finish and defined edges also support clean alignment during fitting. On the workbench, this set suits rebuilds after heavy running, careful restoration of an older Lunch Box, or keeping spare components ready for future service. It also fits organized parts storage for hobby rooms where model-specific replacement sets help keep maintenance straightforward. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
LW X-Joint for W Cardan, model spare part
300042319€5.69
The LW X-Joint for W Cardan is a dedicated spare part set for compatible model driveline assemblies. With 4 replacement pieces in the pack, it supports routine maintenance where worn joint parts can affect the movement of a W Cardan setup during running sessions. Used in the correct compatible assembly, each X-joint serves as a small but important connection point within the driveline. Replacing these parts can help restore the intended fit and motion of the mechanism without changing the overall layout of the model. The set is suited to workshop stock, scheduled service work, or repair after wear on an existing compatible setup. Its focused format keeps the purchase tied to one concrete task: renewing the X-joint section of a W Cardan assembly with matching spare parts. On the bench, the 4-piece pack is practical for keeping replacement parts ready before a maintenance session starts. It also suits hobby storage where frequently used driveline spares are kept together for compatible model repairs and ongoing upkeep. Warning! Not suitable for children under 14 years.
Screws & ball head screws
M 4 x 11,5mm Step Screw/King Pin, RC spare part
300084175€2.19
This spare-parts set supplies 5 M 4 x 11,5 mm step screws/king pins for selected R/C machines, with a stepped metal form that combines a smooth shoulder section and a threaded end. That layout suits fastening points where parts need both guided location and secure fixing, making the set useful for routine maintenance, worn-part replacement or keeping matching hardware on hand for workshop stock. Each screw uses a slotted dome head, giving a clear contact point for fitting and removal with the appropriate tool. The 11,5 mm length and M4 format identify the hardware precisely, which helps when replacing like for like instead of mixing different screw types in one assembly. As a king pin or step screw, this part is intended for positions where the shoulder section matters as much as the thread, rather than acting as a standard fully threaded fastener. The set is listed as compatible with selected R/C machines including Fiat 500, Team Repsol Mitsubishi Ralliart Racing LANCER, Baja King, DualHunter and Plasma Edge. It fits naturally into repair sessions, rebuilds after heavy running, or parts sorting in a model workshop where exact hardware size matters. Warning! Not suitable for children under 14 years.
Axes & drive shafts
M-03 Assembly Universal Shaft, RC spare part set
300053597€51.99
The M-03 Assembly Universal Shaft set brings a serviceable drivetrain upgrade to compatible Tamiya chassis with 2 cardan shafts supplied as 15-piece assemblies. Each shaft is built to be assembled and disassembled, giving direct access to the joint parts during installation, cleaning or routine running maintenance. This set is specified for the M-03 chassis and also fits M-05, M-05 PRO, M-05 ver.II PRO, M-06, M-06 PRO and MF-01X chassis. The interchangeable references 53499, 53500, 53681 and 54410 make it easier to match an existing parts list when refreshing a drivetrain or replacing earlier shaft sets. For MF-01X chassis, the data notes combined use with 54000. The included layout shown for the set covers the shaft components, small hardware and assembly tool needed for the 2 shaft builds. In workshop use, the take-apart construction supports regular inspection of the moving joint sections after repeated running sessions. During a rebuild of an M-chassis touring car, the set gives a clear route to replacing worn drivetrain parts while keeping compatibility across several related platforms. Warning! Not suitable for children under 14 years.
Gears & motor pinions
M-05 Ball Bearing Set, chassis accessory, 18 pcs
300054179€41.49
The M-05 Ball Bearing Set is a chassis accessory made for M-05 machines and brings the full bearing count needed for a focused running gear update into one pack. With 18 metal ball bearings in 2 specified sizes, it supports smoother mechanical movement at the points where rotating parts meet, helping the chassis run with less drag during regular use. The set contains 6 x 850 ball bearings and 12 x 1150 ball bearings, matching the size combination stated for M-05 chassis compatibility. That size split makes the set useful for planned maintenance as well as for replacing worn bearings during a rebuild. In an RC chassis, ball bearings sit at key rotating points and reduce friction compared with basic bushings, which can help the drivetrain turn more freely and keep the response of the running gear more consistent. The silver-coloured metal finish reflects the precision-part character of the set and fits the technical look of workshop spares and tuning parts. On the bench, this bearing set suits routine chassis servicing, parts replacement after extended running, or preparation for a cleaner rolling setup before the next session. It also works as a practical stock part for M-05 owners who prefer to keep the specified 850 and 1150 bearing sizes ready for future maintenance.
Axes & drive shafts
M-05 C-Parts, suspension spare parts set
300051391€17.49
The M-05 C-Parts suspension spare parts set supplies the designated C section for several compact Tamiya chassis, making it a practical choice when suspension-related components need replacement during maintenance or repair. With 46 pieces on 1 parts tree, the set groups matching molded sections together for rebuild work on compatible RC car platforms. Compatibility covers M-06, M-06 PRO, M-05 ver.Ⅱ PRO, M-05, M-05 PRO and MF-01X chassis. That broad fit makes this set useful for workshops, spare parts storage and ongoing running repairs across more than one chassis type. The molded parts format also helps identify and separate the required sections before installation, which keeps rebuild work organized when replacing worn or damaged areas. Scope of delivery: 1x C parts, 46 pieces. This spare parts set suits routine servicing after track use, collision damage or part loss during disassembly. It also fits planned refresh work on an existing chassis, where keeping the correct designated section on hand can shorten downtime between maintenance sessions. Warning! Not suitable for children under 14 years.
Axes & drive shafts
M-05 F-Teile, spare parts set, wheel hub
300051393€9.39
The M-05 F-Teile set is a dedicated spare parts pack for compatible Tamiya chassis, supplying 12 replacement components for maintenance on running gear assemblies. The set is intended for M-06, M-06 PRO, M-05 ver.II PRO, M-05 and M-05 PRO chassis, making it a practical match when original parts need replacement after regular use. The included F parts are shown as black moulded resin components with multiple mounting holes, pivot points and axle or bearing openings shaped for their specific positions in the assembly. Left and right mirrored forms support correct placement during rebuilds, while the mix of upright, hub and small insert style pieces helps address wear in connected front-end areas. This kind of chassis-specific parts pack is useful when keeping an existing RC car in running condition rather than replacing a full assembly. On the bench, the set suits routine servicing, repair after contact damage, or preparation of a second chassis for use with the same platform family. It also helps maintain parts support across several related M chassis versions, which is useful for hobby setups that rotate between M-05 and M-06 based builds. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
M-05 Ver.II A Parts, chassis spare parts set
300054605€18.79
The M-05 Ver.II A Parts chassis set is a focused upgrade and replacement option for the M-05 platform, bringing Ver.II chassis geometry to existing builds while also restoring worn sections on the M-05 Ver.II PRO. Black molded chassis components form the core of the set, with the layout shaped around updated battery and servo fitment options. Within the chassis, parts A8 and A9 allow installation of square-shaped battery packs in place of earlier chassis pieces, and the instruction data notes that the battery pack is secured with glass tape. A redesigned A3 section opens space for a low-profile servo during assembly, while standard-size servo installation uses part A7 with 3 x 18 mm tapping screws. The motor position shifts 3 mm closer to the center, changing the weight distribution within the chassis. The set is also compatible with Item 54606 one-piece lower suspension arms, which allows rebound stroke adjustment when that arm set is used. Some bodies may require trimming where they interfere with the chassis. This chassis parts set suits maintenance, repair and specification updates on compatible M-05 variants. It fits naturally into workshop sessions that focus on replacing broken sections, adapting battery layout, or revising servo placement on an existing front-wheel-drive touring car build.
Axes & drive shafts
M-05Ra F-Parts, RC chassis parts set
300051425€9.99
The M-05Ra F-Parts set is a dedicated RC chassis parts set for the M-05 RA chassis, centered on the upright front and rear area. With 21 pieces in 1 F-parts frame, it provides the specific molded shapes needed when a suspension or steering section has to be rebuilt with matching left and right components. The set contains black molded parts with multiple mounting holes, cylindrical pivot sections and forked connection points. These details matter during assembly because they define how links, axles and adjacent hardware sit in the chassis. The layout shown for the parts also includes small spacers, washers and connector plates, which support alignment and spacing in the assembled upright section. Rather than replacing unrelated sections, this set addresses one clearly defined area of the M-05 RA platform. That focused fitment suits maintenance after heavy running, accident damage or a full chassis refresh. It also helps when keeping a build consistent with the original M-05 RA configuration, using parts intended for that exact platform. The scope of delivery contains 1x F parts set with 21 pieces. Warning! Not suitable for children under 14 years.
Gears & motor pinions
M-07 Concept Spur/Counter Gear RC Spare Set
300051601€4.59
The M-07 Concept Spur/Counter Gear set is a model-specific transmission spare for M-07 Concept chassis cars, supplying the 2 molded gearbox gears needed for a full internal replacement. The set contains 1 main spur gear and 1 counter gear, each formed as a compound gear so the paired tooth counts work together inside the gearbox. The spur gear is specified as 37T/21T and the counter gear as 29T/23T. Those tooth combinations are the key mechanical detail of the set, because they determine how the gears mesh across the transmission stages in the M-07 Concept gearbox. As replacement parts, these gears are intended to renew the internal drive path where wear or damage affects smooth running. The studio image shows white molded gears with fine, evenly spaced teeth, hollow center openings and integrated stepped sections shaped for their gearbox positions. This set suits routine drivetrain maintenance on an M-07 Concept chassis car or a targeted gearbox rebuild after heavy use. Kept in a pit box, workshop drawer or spares case, the matched pair gives a direct way to restore the complete gearbox with the specified gear combination for this chassis platform. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
M-08/M-07 Concept A Parts, chassis spare set
300051595€14.29
The M-08/M-07 Concept A Parts set is a dedicated spare tree for keeping compatible chassis cars ready for service. Designed for the M-08 CONCEPT chassis and M-07 CONCEPT chassis, it supplies the A parts needed when original mounting components are damaged, worn or missing after regular RC use. The set contains 1x A parts tree with 24 pieces and provides spares to replace parts on 1 chassis. Its focus is the body mounting area: body mounts and body mount stiffeners restore the connection points that support the shell on the chassis. That makes this set useful when a shell no longer sits correctly, when mounting points have been stressed during running, or when a rebuild calls for fresh hardware from the original parts group. As a model-specific spare set, it stays close to the intended chassis layout instead of relying on mixed universal hardware. The parts suit workshop stock, routine maintenance and targeted repairs on compatible M chassis builds. During a rebuild, the tree format helps keep related components together while damaged pieces are exchanged. For regular RC maintenance, this spare set covers a focused section of the chassis with the exact A parts group named for the M-08 CONCEPT and M-07 CONCEPT platforms. Warning! Not suitable for children under 14 years.
Gears & motor pinions
M-08/M-07/TA06 Gear Diff. Gasket (2), spare part
300051464€2.69
This spare part set provides gear differential gaskets for compatible Tamiya chassis and supports clean, precise maintenance of the cone differential area. The pack contains 4 flat gaskets, each formed as a circular seal with a shaped center opening, 4 inward tabs and 4 outer holes for the matching mounting pattern. Compatibility covers M-08 CONCEPT, M-07 CONCEPT, TA06, TA06 PRO, TA06 MS, TA05 Ver.II, TD2, TD4, DB01, FF-04 EVO, TRF503, TRF211XM, TRF201XMW, XV-01, XV-01 PRO and XV-01T chassis. For specific setups, TA05 Ver.II uses the gasket with 54312, DB01 uses it with 54329, and TD4 and TD2 use it with 54471. The thin gasket format suits replacement during differential service when worn or compressed seals need to be exchanged for matching new parts. In workshop use, the 4-piece pack supports repeated maintenance sessions or more than one compatible chassis in the collection. The clearly defined cut shape helps align the gasket with the cone differential section during installation, keeping service work focused on fit and correct parts matching. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Manta Ray A-Parts Gearbox Spare Parts Set
300005375€15.49
The Manta Ray A-Parts gearbox set supplies replacement molded components for the 58087 model, centering on the transmission and nearby chassis-mounted assemblies. The black parts come on a single sprue, making each section easy to identify before cutting and positioning during repair or rebuild work. Visible pieces include a large gearbox housing with multiple screw holes, a separate cover or mounting plate, a cylindrical housing element, several hexagonal hub-like parts, and a wider support bracket. This mix supports work in the drivetrain area where aligned mounting points and matching shapes matter. Because the parts are molded as a coordinated set, the geometry across the housing and support sections stays consistent with the intended assembly. The sprue format also helps keep smaller pieces together until they are needed at the bench. This spare parts set suits restoration of a used chassis, replacement of worn transmission-area pieces, or preparation of a stored Manta Ray 58087 for running condition again. It also fits organized workshop stock where model-specific service parts are kept ready for future maintenance.
Gears & motor pinions
MB-01 29T Pinion Module 0.6, RC pinion gear
300051726€5.39
The MB-01 29T Pinion Module 0.6 is a drivetrain spare part made for the Tamiya MB-01 chassis. With 29 teeth and module 0.6 gearing, it gives the transmission a clearly specified replacement component for maintenance work, rebuilds and planned parts stocking around an existing MB-01 setup. The compact gear uses a toothed outer profile and a central mounting hole to sit in the drive system as intended for this chassis platform. The engraved 29 marking provides a quick visual check during bench work, which helps when matching the installed ratio to workshop notes or separating parts between different builds. As a single-piece replacement, it suits targeted servicing where one worn pinion needs to be exchanged rather than a full drivetrain refresh. The metal construction also makes it a natural fit for a mechanical assembly that depends on accurate tooth engagement. In workshop use, this pinion gear supports routine transmission maintenance, parts sorting and chassis-specific repairs. It also works well as a spare kept alongside other MB-01 running gear, ready for rebuild sessions or for replacing a used gear after repeated track time. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
MB-01 A-Parts Uprights, chassis parts set
300051719€7.19
This MB-01 A-Parts set brings several core chassis pieces together for focused maintenance on the MB-01 platform. The pack contains uprights, a gear cover, suspension mounts, a damper stay and hex hubs, giving rebuilds and repairs the matching parts needed for the correct locations within the chassis layout. The different components cover multiple mechanical jobs across the car. Uprights sit at the wheel ends and provide the mounting points around the axle area, while the hex hubs connect the wheel fitment to the drivetrain side. The gear cover closes off part of the transmission area, and the suspension mounts and damper stay support the placement of suspension and damping hardware on the chassis. Because these parts are supplied as A-Parts for the MB-01 chassis, the set suits replacement of worn pieces, accident damage or missing original components without mixing unrelated hardware. On the bench, this set supports anything from a single damaged corner repair to a broader chassis overhaul. It also works well as workshop stock for MB-01 owners who want the correct molded parts ready for routine service, rebuild planning or trackside maintenance between running sessions.
Axes & drive shafts
MB-01 C-Parts Transmission Spare Parts Set
300051721€7.19
The MB-01 C-Parts Transmission set supplies replacement drivetrain parts for the MB-01 chassis, centering on the transmission area where matched fit matters most. Black molded components and metal shaft sections form a compact service set for restoring the original mechanical layout with the specified C-parts. Included are differential cup joints, axle shafts, dogbone shafts and propeller shafts, grouped for transmission-related maintenance on the MB-01 platform. The forked cup pieces and connecting shafts handle the mechanical link between rotating drivetrain sections, while the smaller spacers and retaining hardware shown in the set support correct assembly of the replacement parts. This makes the set useful when worn or damaged transmission components need to be exchanged with the designated matching parts rather than improvised substitutes. On the workbench, the set supports targeted repair of an MB-01 drivetrain without changing to a different chassis standard. It suits routine maintenance, rebuilds after heavy running, or keeping spare transmission components ready for the next service interval on an MB-01 model.
Gears & motor pinions
MB-01 D-Parts Gearbox, chassis spare parts
300051722€9.49
The MB-01 D-Parts Gearbox brings together key chassis components for repair, maintenance and parts replacement on the MB-01 platform. This sprue covers several of the mechanical sections that shape the layout of the chassis, with moulded parts for the drivetrain area, deck structure and steering system arranged as one matched set. Alongside the motor mount, gearbox and upper deck, the set also provides an R/C equipment deck and wheelbase adjustment parts for the MB-01 chassis. The black moulded pieces show reinforced ribbing, axle openings, hinge points and screw locations that suit structural mounting and gearbox housing tasks within the chassis build. Because these parts are supplied together on the D-Parts sprue, matching sections can be replaced with the correct group intended for the same platform. This set suits workshop use when an MB-01 chassis needs worn or damaged sections exchanged, or when a stored build is being returned to running condition with the proper chassis hardware. It also fits ongoing bench maintenance where drivetrain housings, steering mounts or deck sections need the original replacement parts for the model. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
MB-01 Full Ball Bearing Set, chassis accessory
300022026€26.29
The MB-01 Full Ball Bearing Set equips the MB-01 chassis with a complete 18-piece bearing package sized for its rotating assemblies. With 12x 1050 bearings, 2x 1280 bearings and 4x 850 bearings, the set brings together the exact mix needed for a full conversion in one chassis-focused pack. Ball bearings are used at points where shafts and axles rotate, replacing plain bushings with rolling elements that reduce friction during operation. In an RC chassis, that lower drag can support freer drivetrain movement and a more direct mechanical feel across the running gear. The different bearing sizes in this set are arranged to match the MB-01 layout, so the contents are not a generic assortment but a model-specific combination for this platform. The compact format also makes the set useful for routine servicing, a fresh build or a rebuild after wear on existing running parts. Kept alongside other workshop spares, the bearing pack gives a straightforward way to refresh the MB-01 chassis with the full quantity already counted out for the job.
Gears & motor pinions
MB-01 G-Parts Gears, chassis parts set
300051723€4.79
The MB-01 G-Parts Gears set supplies drivetrain-related replacement parts for the MB-01 chassis, centered on a G-Parts sprue with a 65T spur gear and differential components. This layout gives the chassis a direct source for key internal gear parts when wear, damage or a full teardown calls for fresh hardware. Within the sprue, the 65T spur gear serves as a defined transmission component rather than a generic gear, while the differential parts address another separate section of the drivetrain. Keeping these parts grouped under the G-Parts designation helps match them to the MB-01 platform during workshop sorting and chassis maintenance. The set is aimed at repair, servicing and parts replacement for an existing model, not at a complete vehicle build. No scale is stated in the data, and the pack is identified specifically for the MB-01 chassis. On the bench, this set fits naturally into routine gearbox service, differential refresh work or a rebuild after heavy use. It also suits keeping a dedicated replacement sprue on hand for the MB-01, so the correct gear and matching internal parts are ready when the chassis is opened for maintenance.
Other spare parts & accessories
MB-01 LD-Parts Fr/Re. Lower Deck, chassis parts
300051725€8.49
The MB-01 LD-Parts Fr/Re. Lower Deck provides the front and rear main chassis sections for the MB-01 platform, giving a model build the structural base that sits at the center of the assembly. These molded chassis parts are intended for replacement, repair or a fresh rebuild where the original lower deck needs to be restored with the correct form and mounting layout. The included parts consist of the main chassis front section and main chassis rear section. In the molded structure, raised side walls, screw mounting posts, recessed fixing areas and formed channels create the attachment points and alignment surfaces needed for surrounding assemblies. This kind of lower deck geometry matters in a chassis build because it determines how major components sit in relation to each other across the front and rear of the platform. The matched front and rear layout also helps maintain the intended fit of connected parts made for the MB-01 chassis. On the bench, these chassis sections suit routine maintenance, accident repair or the revival of a stored model that needs a new structural core. They also work well as workshop spares for MB-01 owners who keep replacement parts ready for ongoing running and rebuild sessions. Warning! Not suitable for children under 14 years.
Axes & drive shafts
MB-01 M-Parts, chassis spare parts sprue
300051724€5.39
The MB-01 M-Parts sprue brings together several of the chassis pieces that matter most when an MB-01 build needs replacement hardware rather than a full new kit. This set is centered on the MB-01 platform and groups key black molded parts on one sprue, making it a practical match for repair work, routine maintenance, or keeping workshop stock ready for the next rebuild. Alongside suspension arms, the sprue also carries body mounts, a bumper and damper shafts, covering parts that sit across the running gear and upper mounting structure. That mix is useful when wear or impact affects more than one area at once, because the set addresses several connected mounting points in a single purchase. The molded layout also helps identify each piece before removal from the sprue, which keeps preparation straightforward at the bench. As a chassis parts set rather than a complete vehicle, it focuses on restoring original MB-01 component positions and connections. On the workbench, this sprue suits planned servicing as well as targeted replacement after track contact or repeated running sessions. It can be kept as a ready spare for an existing MB-01 chassis or used when a rebuild calls for fresh molded components in the suspension and body support areas.
Other spare parts & accessories
Mt.Beetle body mount parts, model accessory set
319000834€12.99
This accessory set provides E Parts body mount components for the 58618 Mt.Beetle and supports accurate replacement work on the body mounting section of the build. The black molded pieces are supplied on a single sprue frame, giving a clear overview of the included shapes before removal and helping keep the parts organized during workshop preparation. Visible on the runner are several distinct molded forms, including bracket-like pieces, rod-shaped elements, a ring-shaped part, a slotted panel and a larger curved housing with round and square openings. That layout helps identify each section during repair or rebuild work and gives model builders the matching geometry needed for the intended mounting area. As a dedicated spare and replacement set rather than a general hardware assortment, it focuses on the specific fit and form required for the 58618 Mt.Beetle. The set works well when an existing chassis needs fresh mounting pieces after wear, loss or damage, or when a stored build is being brought back into running condition with matching replacement parts. It also suits bench stock for ongoing maintenance, where the correct molded components are ready for the next rebuild step. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
O-Ring 3x6mm Red, RC spare part for dampers
300050597€3.39
This 10-piece pack of red O-rings in 3 x 6 mm format is made for damper and wheel axle use on selected RC chassis, giving a compact spare set for routine maintenance, worn seal replacement and parts-box stock. The small ring size suits jobs where a matching dimension matters, whether the work focuses on suspension service or axle-related fitting points. Compatibility is clearly defined across several chassis families. The O-rings can be used on TT-02, TT-02D and TT-02FT vehicles equipped with 50746, on TT-01 TYPE-E vehicles equipped with 53619, and on DT-03 or DT-03T vehicles equipped with 54567. TT-02RR lists this part as standard kit equipment. For DT-02, XB cannot be used, so chassis version and installed parts should be checked before fitting. In workshop use, a 10-pack keeps matching replacements ready for rebuilds, scheduled servicing or the correction of worn damper and axle seals after regular running sessions. The simple scope of delivery keeps the focus on the parts themselves: 10 O-rings for compatible RC maintenance tasks. Warning! Not suitable for children under 14 years.
Screws & ball head screws
OF 5mm Adjusters L, RC accessory, open face
300054869€5.59
OF 5mm Adjusters L is an RC accessory set for linkage tuning and replacement work on compatible models. The pack contains 8 open face reinforced adjusters, each with a 15 mm length, for use in place of standard 5 mm adjusters when a longer rod-end style connection is needed on a mechanical linkage. The instruction diagram shows the adjusters fitted to a threaded rod with grease applied to the threads before assembly. Installation also has a defined orientation: the side marked with a circle symbol is pressed onto the ball connector. That detail matters on steering and suspension style linkages, where the joint needs to seat correctly on the ball stud for clean movement. Different lengths are available separately, which helps keep the setup matched to the geometry required by the model. This set suits maintenance, replacement and setup changes on RC assemblies that use 5 mm adjusters. During fitting, some models may require filing down, depending on the surrounding layout and available clearance at the linkage point.
Screws & ball head screws
OF 5mm Adjusters M, RC accessory, open face
300054868€5.59
The OF 5mm Adjusters M open face set adds a focused tuning and maintenance part for RC linkages, with 8 reinforced adjusters sized for use in place of standard 5 mm adjusters. The 11.5 mm medium length gives a concrete reference when matching an existing setup or planning a replacement during chassis work. The fitting method is clearly defined by the part design. Grease is applied to the threads before the linkage ends are screwed on, and the side marked with a circle is the side that presses onto the ball connector during installation. That orientation detail matters when assembling steering or suspension linkages, because the adjuster is designed to seat in a specific direction rather than as a symmetrical push-on part. The open face construction also supports direct use in rod-end style ball-joint connections where a standard 5 mm adjuster is being swapped out. On the bench, this 8-piece pack suits repair jobs, replacement of worn linkage ends, or small setup changes across compatible RC models. Some models may require filing down during fitting, so the part can be adapted where surrounding components leave limited clearance.
Shock absorbers & springs
Oil Damper VG O-Rings 30deg, damper parts
300042359€9.19
Oil Damper VG O-Rings 30deg are replacement damper parts made to keep oil dampers working with a clean, responsive feel. The 30deg specification is tuned to support strong initial response, which is especially useful when older seals have started to lose their original performance during repeated running. The set contains 8 O-rings in a navy blue finish for routine maintenance or a planned damper refresh across multiple units. Their high-spec construction is designed to minimize the amount of air forced into the dampers while the model is moving, helping the oil circuit stay more stable through longer sessions. That reduction in trapped air supports more even damping behavior instead of the less consistent action that can appear as seals wear. As a focused replacement part, this set suits regular workshop servicing as well as targeted tuning when damper response needs attention. During rebuilds, race-day maintenance, or general suspension servicing, a fresh set of O-rings can make a noticeable difference to how smoothly the dampers cycle. Keeping spare seals on hand also helps maintain a dependable setup between runs when worn internal parts need a direct replacement.
Shock absorbers & springs
On-Road Spring Set, tuning accessory, hard medium soft
300053163€21.29
This on-road spring set adds a wider suspension tuning range to compatible RC chassis with 6 springs in hard, medium and soft rates. The colour-coded finish in fluorescent red, fluorescent yellow and fluorescent blue makes each rate easy to identify during setup changes, helping keep adjustments organised between test sessions and repeat runs. The set is described as a softer spring kit than OP440, which opens another direction for chassis tuning when a setup calls for more compliant suspension response. It is intended for use across a broad group of platforms including F104PRO II, F104W, F104, F103GT, M-07 CONCEPT, M-06, M-06 PRO, M-05 ver.II PRO, M-05, M-05 PRO, MF-01X, TT-02FT, TT-02RR, TT-02D, TT-02 and TT-01 TYPE-E. For F104 and F104W chassis, the data specifies use with 53901. On the workbench, the 3 spring rates support direct comparison of suspension behaviour during circuit setup, whether the focus is front-end response, overall balance or matching the chassis to track conditions. Scope of delivery: 6x springs hard, medium, soft. Warning! Not suitable for children under 14 years.
Gears & motor pinions
Pinion Gear-Set 16/17T Alu M0.6 for RC Chassis
300050354€8.99
This aluminum pinion gear set brings 2 tooth-count options to compatible RC chassis, with one 16T gear and one 17T gear in M0.6 pitch for drivetrain replacement or gearing changes. The silver-finish parts have a compact machined form, and each pinion is secured with a grub screw for firm mounting on the motor shaft. The set is intended for clearly defined chassis combinations rather than general use. TT-02FT, M-05, M-05 PRO, M-05 ver.II PRO, M-06 and M-06 PRO chassis use only the 16T gear. XV-02PRO, TA07 PRO, TA08 PRO and M-08 CONCEPT chassis use only the 17T gear. For F104PRO II chassis, the set is used with 51609. For TA07 MS chassis, only the 17T gear is usable and it is used with 51356, 51423 and 51548. Scope of delivery: 2 pinions and 2 grub screws. That makes the set a practical choice for workshop stock, scheduled maintenance or a direct replacement when a specific chassis calls for one of these tooth counts. In a bench setup, the stamped 16 and 17 markings help identify the correct gear quickly before installation, keeping chassis-specific drivetrain work clear and organized. Warning! Not suitable for children under 14 years.
Gears & motor pinions
Pinion Gear-Set 18/19T Alu M0.6, RC gear set
300050355€9.99
The Pinion Gear-Set 18/19T Alu M0.6 brings 2 aluminum motor pinions into one compact drivetrain set, with 18T and 19T tooth counts for compatible Tamiya chassis. Each gear mounts with a grub screw, creating a firm connection on the motor shaft for controlled power transfer through the drivetrain. This set is intended for tuning, replacement and maintenance work across several chassis families. It fits M-05, M-05 PRO, M-05 ver.II PRO, M-06, M-06 PRO, WR-02, WR-02G, WR-02C and WR-02CB chassis. Use on some platforms follows specific tooth-count rules: GF-01CB uses only the 18T pinion, while TT-01 TYPE-E and TT-01D TYPE-E use only the 19T pinion. F104PRO II uses the set with 51609, TA07 MS Chassis uses it with 51356, 51423 and 51548, and F103GT uses only the 18T pinion with 50506. In workshop use, the 2 included pinions give a straightforward way to compare gearing options during a rebuild or drivetrain refresh. The M0.6 specification keeps the set aligned with matching gear applications, whether the goal is restoring a worn drive part or preparing a chassis for a different running setup. Warning! Not suitable for children under 14 years.
Gears & motor pinions
Pinion Gear-Set 22/23T Alu M0.6, RC gear set
300050357€9.99
This pinion gear set brings 2 aluminum motor pinions into one compact drivetrain upgrade for compatible RC chassis. With 22T and 23T tooth counts and an M0.6 specification, it supports clear gearing choices when adjusting acceleration response or matching a replacement part during maintenance. Each pinion is machined with a central bore and a side threaded hole for the grub screw, so the gear mounts directly to the motor shaft in a straightforward mechanical layout. The included contents are 2 pinions and 2 grub screws. The 22T and 23T markings on the gears make identification quick during setup, storage or parts sorting. Aluminum construction keeps the set focused on a precise drivetrain component rather than a general hardware mix. For TT-01 TYPE-E chassis, the set offers both tooth-count options, while TT-01D TYPE-E chassis can use only the 22T gear. On the bench, this set suits routine replacement work, ratio comparison between 22T and 23T, or keeping a second pinion ready in the parts box for compatible RC running sessions. It also fits neatly into a workshop stock of drivetrain spares where exact tooth count and pitch matter. Warning! Not suitable for children under 14 years.
Gears & motor pinions
Pinion Gear-Set 24/25T Alu M0.6, motor pinion set
300050477€10.79
This motor pinion set brings a focused drivetrain upgrade to compatible RC chassis with 2 aluminum pinions in 24T and 25T plus 2 grub screws for mounting. The M0.6 gear specification makes it a targeted choice for model builders who need the correct tooth pitch for matching transmission parts and a clean fit on the motor shaft. The set is intended for several established chassis platforms in the Tamiya range. It fits M-07 CONCEPT and M-08 CONCEPT chassis, with the note that only the 24T pinion can be used on M-08 CONCEPT. It also fits TT-01 TYPE-E and TT-01D TYPE-E chassis, where it is used with 53665. That compatibility detail matters during drivetrain setup, because the pinion must match both the chassis layout and the related gear components already in use. The aluminum construction adds a crisp machined finish and a precise look that suits technical RC assemblies. On the bench, this set supports replacement work after wear or a gearing change during a fresh build. In workshop use, the 2 included pinions give a direct choice between 24T and 25T, while the grub screws complete the mounting hardware needed for installation. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
R/C Body Mount Hole Patches, RC accessory, 0.5 mm
300054785€6.69
These R/C body mount hole patches add discreet reinforcement where bodyshells take repeated stress. The clear 0.5 mm material strengthens the area around each mounting point while leaving the shell finish visible, so repairs stay unobtrusive on painted or decorated bodies. Each sheet provides 8 patches, giving several mounting points the same treatment in one session or leaving spares ready for later maintenance. The 6.5 mm internal diameter is sized for use on most body mount holes, making the patches a straightforward choice for many R/C bodyshell layouts. Their ring format focuses support around the opening itself, where cracks and widening can start after repeated fitting, removal and running. In workshop use, the patches suit routine bodyshell upkeep before damage spreads further around the post area. They also work well when refreshing a frequently used shell, helping keep mounting holes neat through repeated body changes between running sessions. This accessory is intended for model hobby use and is marked 14 years and up.
Other spare parts & accessories
RC Servo Saver Kit, universal chassis accessory
300050204€6.79
This RC servo saver kit adds an adjustable steering connection for a wide range of chassis layouts while helping reduce shock loads passed into the servo during running. The set is designed for universal use and is listed for many Tamiya platforms including M-06, M-06Pro, F104, F104 Pro II, DT-02 and DT-03, making it a practical choice for repairs, replacements or fresh steering setups. Several servo saver bases are provided so the mounting interface can be matched to different servo makes. The instruction data names base options for Futaba, Sanwa, Acoms, JR and KO, allowing the spline connection to be selected according to the servo in the chassis. Two spring rates are included: S6 strong and S9 weak. The assembly diagrams also show separate configurations for off-road car and racing car use, with S3 or S5 upper parts chosen according to the layout. Mounting hardware covers 3 mm x 12, 2.6 mm x 10 and 2 mm x 10 screw formats, with S1 and S2 spacers assigned to the screw diameter. During setup, the saver arm can be arranged to suit the direction of the servo in the car, and the linkage can be attached by cranked rod or by ball pin depending on the steering system in use. That makes the kit useful both when restoring an older chassis and when refining a custom RC build around the available servo and linkage parts. Warning! Not suitable for children under 14 years.
Screws & ball head screws
Router Ctrsk Bit for 2mm Screw, tool accessory
300074130€7.19
The Router Ctrsk Bit for 2mm Screw is a workshop accessory for cutting neat countersunk holes in small machine parts. Its diamond particle coated conical head removes material cleanly in carbon fiber, FRP and similar surfaces, so 2 mm countersunk screws can sit flush instead of leaving the head raised above the part. Beyond countersinking, the flat sides of the head can be used to shape edges during detail work. The #200 particle size gives the abrasive surface a defined cutting character for controlled material removal on compact components. This makes the bit useful when refining Mini 4WD parts that need a cleaner screw seat or a tidier edge profile. Made for use with routers such as the Tamiya Electric Handy Router Item 74042, it supports focused modification work where accuracy matters on every pass. On a tuning bench, the bit helps prepare carbon fiber and FRP parts for a lower-profile screw fit that keeps surfaces cleaner around mounting points. It also suits small finishing jobs where edge shaping and countersinking are handled with the same accessory in a compact tool setup. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Rubber Tire Cement LoVis. 25g, RC tire adhesive
300054511€14.49
Rubber Tire Cement LoVis. 25g is a dedicated CA cement for R/C car rubber tires, made for clean bonding work where a tire bead meets the wheel. The low-viscosity formula flows smoothly into narrow seams, so the adhesive can reach the joint itself instead of sitting on the surface. The bottle contains 25 g of cement and uses a fine nozzle for controlled application in small contact areas. That layout helps when working around the full circumference of a wheel, where steady placement matters more than excess glue. The adhesive is supplied in a bottle with an aluminum bag that limits humidity during storage. In workshop use, that added protection supports more consistent handling when the cement is opened again for later tire maintenance. The source data identifies this as CA cement for rubber tires, giving it a focused role within R/C car setup rather than general household bonding. It fits naturally into bench work before track sessions, when fresh rubber tires are mounted to wheels and the bead needs an even seal. It also suits repair tasks after running, when a lifted section at the joint calls for careful re-bonding with a smooth-flowing adhesive. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
Sand Scorcher Rear Guard, model accessory
319335554€10.29
This rear guard is a dedicated model accessory for the Sand Scorcher and is listed for chassis references 58441 and 58452. The included contents are 1 protective bar, giving a clearly defined replacement part for the rear section rather than a mixed hardware assortment. Its focused single-part format helps when a specific rear component needs to be replaced during maintenance, repair or restoration work. The stated fitment to 58441 and 58452 keeps compatibility clear at a glance and supports accurate parts selection for the matching Sand Scorcher versions. Because the set contains one rear protective bar, the part can be kept on hand for workshop stock, planned rebuilds or the replacement of a missing original component. On the bench, this accessory suits routine service work where the rear section needs the correct guard rather than a universal substitute. It also fits restoration projects that aim to return a Sand Scorcher to its intended rear layout with the proper dedicated replacement part. Warning! Not suitable for children under 14 years.
Screws & ball head screws
Screw Bag D BD1-7, model hardware set
319465797€10.89
Screw Bag D BD1-7 is a model hardware set built around the small fastening parts that keep an assembly moving. The pack brings together metal screws, hex nuts, flat washers, split lock washers and threaded spacers, giving compatible model builds the exact kind of joining and spacing parts that are often needed during maintenance or part replacement. The combination of different fastener types supports more than one task within a build. Screws and nuts handle fixed connections, washers sit between parts to spread contact, and split lock washers help hold tightened joints in place. Threaded spacers add distance where mounted sections need clearance between components rather than direct contact. This makes the set useful not only when hardware has been lost, but also when an older build is being refreshed with matching replacement fittings. On the bench, the assortment suits repair sessions, rebuild work and careful parts sorting before assembly starts. The compact hardware format also makes it practical to keep alongside compatible model kits as a dedicated source for replacement fixings when a single missing fastener would otherwise stop progress.
Other spare parts & accessories
Servo Saver P-Parts Set for DT-03 and DF-03
300115065€4.49
This servo saver P-parts set is made for compatible DT-03, DT-02 and DF-03 chassis and supplies the shaped components needed when the original steering parts need replacement. The runner format keeps each piece organised and easy to identify before removal, which helps when checking parts against the build or service instructions. The moulded frame shown here carries numbered components, including ring-shaped and bracket-style pieces used within the servo saver assembly. That layout supports careful maintenance because each part stays attached until the moment it is needed. For older kits, workshop repairs, or chassis refreshes, a dedicated spare set like this helps return the steering mechanism to its intended configuration without substituting unmatched pieces. On the bench, the set suits routine servicing, rebuilds after heavy running, or the completion of a partly used kit where original P-parts are no longer available. It also works as a practical stock spare for model collections built around the DT-03, DT-02 or DF-03 platform. Warning! Not suitable for children under 14 years.
Screws & ball head screws
Servo Step Screws, aluminum accessory set of 4
300054862€10.89
These aluminum servo step screws are made to improve the way a servo sits in its mounting points, combining a precise fit with a clean hardware layout. The set contains 4 screws, each shaped to suit holes between 4.5 mm and 5 mm, so the screw seats more securely in the opening instead of relying on extra spacing parts. The metallic finish and machined form give the hardware a crisp technical look that matches detailed model builds and electronics work. A stepped profile is the key feature here. By filling the mounting hole more accurately, the screw helps reduce play at the fixing point and supports a tighter connection around the servo case. The integrated shoulder also means separate washers are not required, which keeps the installation simpler and leaves fewer loose parts to track during routine servicing. Hex socket heads add another practical detail, allowing a tool to seat firmly in the screw head for controlled tightening in compact spaces. These screws suit upgrade work, replacement hardware needs, or a fresh servo installation where a closer fit is wanted at the mounting holes. Depending on the servo design, only 2 screws may be needed, leaving the remaining hardware available as spares for later maintenance or another compatible setup.
Axes & drive shafts
Shaft 2 x 9.8 mm, model spare part, 10 pcs
309805776€3.99
This spare shaft set brings exact replacement dimensions to model maintenance with 10 steel shafts measuring 2 x 9.8 mm. The compact format suits small mechanical assemblies where a worn, bent or missing shaft can affect how connected parts sit and move. The 2 mm diameter and 9.8 mm length give a clear reference for matching an existing part before installation. As a workshop consumable, the set supports repeated servicing across compatible hobby models instead of relying on a single replacement piece. The short shaft format is suited to detail areas where space is limited and clean alignment matters. Keeping identical spares on hand can simplify routine upkeep when several connection points use the same measurement. In a home workshop, club pit area or model bench, this shaft pack fits neatly into regular maintenance supplies for ongoing repair work. It also serves as a practical stock addition when checking assemblies, replacing lost hardware or preparing compatible builds for the next running session. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
Silicone Damper Oil Hard Set, RC oil, #800/900/1000
300053445€20.991 l = €349.83
The Silicone Damper Oil Hard Set brings firmer suspension tuning to RC maintenance with 3 silicone-based oils in grades #800, #900 and #1000. Each bottle contains 20 cc, and the pointed applicator nozzle helps guide the fluid into compact damper bodies with controlled dispensing during rebuilds or setup work. This set is intended for oil pressure dampers and is tailored to Tamiya applications where damping changes are part of chassis adjustment. Higher viscosity means thicker oil and a harder damping feel, so the three grades in this set give a practical range for comparing response and refining how a model settles through corners, braking zones and uneven sections. The bottles are colour coded as pink, clear and light blue, making the three viscosities easier to distinguish on the bench. The fluid is identified for shock absorber use on model vehicles, and the set can also extend the available tuning range when combined with the softer companion sets in the same series. Compatibility listed in the data covers CC-01, F103GT, TB-03 and TB-03 VDS chassis. That makes the set a useful workshop supply for regular servicing, seasonal retuning or keeping several RC builds ready with different damper fills for changing surfaces and handling preferences. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
Silicone Damper Oil Medium Set #500 #600 #700
300053444€20.991 l = €349.83
This silicone damper oil medium set brings 3 tuning grades together for model vehicle shock absorbers: #500, #600 and #700. The three 20 cc bottles cover the medium range in Tamiya's viscosity system, where a lower number indicates a lower viscosity and a higher number indicates a thicker oil, making step-by-step suspension changes easier to plan at the workbench. The set is intended for model vehicles and uses silicone-based oil in 3 colour-coded grades: green #500, blue #600 and purple #700. At 25 °C, the kinematic viscosities are 500 mm2/s, 600 mm2/s and 700 mm2/s. This spacing supports direct comparison between nearby setups instead of forcing a large jump in damping feel. The pointed bottle tips support controlled dispensing into damper bodies during filling, topping up or rebuild work, and the 20 cc fill quantity on each bottle gives enough material for repeated service sessions. On an RC chassis, these 3 grades can be used when refining how quickly the suspension moves over bumps, settles after compression or reacts to changing grip levels. The set suits routine maintenance as well as test sessions where several oil weights are compared back to back on the same model vehicle.
Shock absorbers & springs
Silicone Damper Oil Soft Set, RC model accessory
300053443€20.991 l = €349.83
This silicone damper oil soft set brings suspension tuning into a clearly graded format with 3 bottles covering #200, #300 and #400 viscosities. The softer range supports fine adjustment of oil-filled dampers on RC model vehicles, whether the goal is a lighter response over uneven sections or a more measured starting point for chassis setup at the workbench. Each bottle contains 20 cc and uses a narrow nozzle that helps guide the fluid into damper bodies with controlled application. The set is identified by red, orange and yellow oils, making the grades easy to separate during rebuilds, refills and comparison testing. The formula is silicone-based and intended for model vehicle shock absorber use. Tamiya's viscosity system follows a simple rule: lower numbers indicate lower viscosity, while higher numbers indicate thicker oil. This soft set can also extend its adjustment range when used together with the medium and hard sets in the same series. Compatible applications named in the data include the GB-01S chassis, CC-01 chassis, F103GT chassis, TB-03 chassis and TB-03 VDS chassis. On a tuning bench, the 3 grades allow direct back-to-back damper changes between runs or during a rebuild, with each step in viscosity offering a clear reference point for suspension experimentation. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
Silicone Diff. Oil #3.000, model supply, 40cc
300054657€9.391 l = €234.75
Silicone Diff. Oil #3.000 is a model supply for tuning oil-filled sealed differential units and roll dampers in R/C cars. The 40cc bottle and narrow nozzle suit careful, repeatable application at the bench when a setup calls for a 3000 weight fluid on faster layouts with long, sweeping turns. The fluid is identified in the technical data as polydimethylsiloxane, with a kinematic viscosity of 3,000 mm2/s at 25 °C. It is a liquid, odourless and insoluble in water, with a relative density of 0.97 at 25 °C. That specification gives a clear reference point when matching maintenance supplies to an existing differential fill or a planned roll damper setup. The bottle format keeps the quantity compact for workshop storage while still covering repeated servicing across compatible R/C car drivetrains. In use, the oil suits rebuilds of sealed differentials after cleaning, routine setup changes between track conditions, or roll damper servicing on formula and RM chassis. On a pit table or home workbench, the 40cc fill offers a practical amount for keeping one viscosity grade ready for regular tuning work. Warning! Not suitable for children under 14 years.
Shock absorbers & springs
Silicone Diff. Oil #4000, differential oil, 40cc
300022006€8.991 l = €224.75
Silicone Diff. Oil #4000 is a tuning fluid for oil gear differentials that brings a clear handling change to model vehicles. The high-viscosity grade is intended to support stable, speedy cornering in the high-speed range, making it a useful choice when differential action needs a firmer setup on faster sections. The bottle contains 40cc of yellow silicone oil and is sized for about 22 uses in touring car different gears. Its bottle format with dispensing nozzle supports measured application during maintenance, refills, or setup changes at the bench. The fluid is identified as #4000 viscosity, and the supplied data lists a kinematic viscosity of 4,000 mm2/s at 25 °C. This Hop-Up Option is intended specifically for model vehicle differentials that use oil as part of their tuning setup. On indoor tracks, club circuits, or home workshop setups, the oil can be used to compare differential feel against lower-viscosity grades and refine how the car responds through faster corners. It suits repeated testing sessions where small setup changes matter, while the 40cc volume keeps enough fluid on hand for ongoing drivetrain maintenance.
Other spare parts & accessories
Sponge Tape for Bumper, model accessory, 10-pack
300054430€4.99
Sponge Tape for Bumper is a compact model accessory for fine-tuning fit in RC car setups. Each foam strip measures 150 x 15 x 2 mm and is shaped to sit neatly where a small gap needs to be taken up. Used between a urethane bumper and the body, the tape helps the shell sit more closely against the chassis line, which can support steadier handling on the race track. The same foam material also serves as a spacer on battery holders. Placed between the battery pack and the chassis area, it creates a tighter contact point that helps reduce movement during running. That makes this 10-pack useful not only for body mounting adjustments, but also for routine setup work across multiple cars or repeated rebuilds. The narrow strip format is easy to trim or position according to the space available, while the 2 mm thickness gives a defined layer for controlled spacing. In workshop use, the tape suits quick pre-run checks, replacement during maintenance, or small chassis adjustments before track sessions. It is a straightforward addition for racers who want closer body fit, tidier battery seating and a more dialed-in setup from simple, measurable material changes.
Other spare parts & accessories
Stabilizer Rod Stopper (4), RC chassis hardware
300053827€11.99
The Stabilizer Rod Stopper (4) is a small but important tuning part for RC chassis stabilizer setups. Each collar is fitted onto the sway bar and tightened with a grub screw to hold its position on the rod, so the bar can pivot up and down as intended while lateral movement is kept under control during loaded cornering. The set includes 4 stabilizer collars and 4 grub screws. This layout supports left and right positioning on a stabilizer assembly and gives a clean mechanical stop on the rod itself. The stopper design works as part of the stabilizer system rather than replacing the bar, and it is used with matching sway bar sets on specified chassis. Compatible applications listed in the data include TA06, TA06 PRO, TA06 MS, TB-04, TB-04 PRO, FF-03, FF-03 PRO, TB-03, TB-03 VDS, TA05 ver.II, M-07 CONCEPT, M-08 CONCEPT, TRF502X and DB02, each with the corresponding referenced set. On a touring car sedan setup, this kind of lateral control helps the stabilizer work consistently through repeated laps and setup changes. It suits maintenance, replacement and fine tuning on compatible chassis builds where accurate bar location matters to suspension response.
Screws & ball head screws
Step Screw 3x14mm BB1, model spare screws
319808289€2.19
Step Screw 3x14mm BB1 is a model spare screw set for builds and repairs that call for this exact hardware format. The pack contains 10 screws, giving a ready supply for maintenance tasks where matching dimensions matter and mixed fasteners can interrupt progress. The 3x14 mm specification provides the key reference for selecting the right screw for a compatible assembly, while the BB1 designation adds a second identification point for parts matching. This combination helps when replacing missing hardware, sorting workshop stock or keeping a current project aligned with its intended screw type. As a dedicated spare part, the set supports precise fastening work in model assemblies that rely on consistent screw sizing. On the bench, the 10-piece pack suits routine servicing, partial rebuilds and keeping reserve hardware available between sessions. It also fits neatly into parts storage for quick access when a compatible model needs the same screw again. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
T3-01 Battery Case, chassis accessory, 4xAA
300051610€21.79
The T3-01 Battery Case adds a dedicated 4xAA power option to compatible T3-01 chassis models and gives the Dancing Rider kit an alternative to NiCD, NiMH or Lithium Ion battery packs. The holder is built around a 6V AA layout, with polarity markings in the tray to guide battery placement and a wired connector lead to link the case to the chassis electronics. Inside the assembly, metal battery terminals, springs, screws and the case sections come together as one complete battery compartment. The closure uses a twist-shut cap that can be turned with a coin, keeping the batteries secured once installed. Red and black cable routing is part of the assembly layout, and the connector orientation matters for correct connection to RC equipment. The case is intended for use with 4 AA alkaline or rechargeable batteries and a compatible ESC. Batteries are not included. This accessory suits T3-01 owners who want a separate battery holder matched to the chassis rather than a rechargeable pack format. It fits naturally into maintenance, replacement or conversion work on a Dancing Rider setup, especially when keeping a ready AA-powered option alongside existing running gear.
Shock absorbers & springs
TA-/TB-/TRF Urethane Front Bumper RC Part
300054145€4.59
The TA-/TB-/TRF Urethane Front Bumper is a chassis tuning part for selected Tamiya on-road platforms, using a larger-than-standard bumper profile to reduce the gap between chassis and bodyshell. That closer fit helps suppress body shimmy during high-speed running, giving the shell steadier support at the front of the car. The part is supplied as 1 foam rammer and is shaped as a curved bumper insert with 2 mounting holes and edge cut-outs for installation on compatible layouts. Supported chassis named in the data include TA07 MS Chassis, TA07 PRO Chassis, TA05 ver.II Chassis, TB-Evo.7 Chassis, TB-Evo.6 MS Chassis, TB-Evo.6 Chassis, TB-05 PRO Chassis, TB-04 Chassis, TB-04 PRO Chassis, TB-03 chassis, TB-03 VDS Chassis, TRF419XR Chassis, TRF419X Chassis and TRF419Chassis. As a front-end setup part, it focuses on shell support rather than decoration, making it relevant where close body fit and controlled movement matter on faster laps. It suits rebuilds, maintenance and setup changes on compatible touring chassis already in use. During track preparation, the larger bumper profile can be fitted when a closer bodyshell position is needed at the nose of the car for more settled running at speed. Warning! Not suitable for children under 14 years.
Gears & motor pinions
TA-01 DF-01 G Parts Gear Set for RC Models
309005322€14.99
The TA-01/DF-01 G-Parts gear set focuses on the mechanical core of compatible RC model assemblies, with injection-moulded components shaped for drivetrain and gearbox-related service work. Visible in the set are a large spur gear with an integrated central bevel gear, 2 medium cylindrical gears with fine outer teeth, smaller gear-form parts on a sprue, and 2 round disc-shaped pieces with raised pegs and centre holes. These parts support repair and replacement tasks where worn, missing or damaged transmission elements affect the running condition of a TA-01 or DF-01 based build. The different tooth forms, mounting holes and moulded connection points indicate use in geared drive sections rather than body or decorative areas. As unassembled service parts, the set gives builders the correct component shapes needed for maintenance without requiring improvised substitutions. On the workbench, the clearly separated moulded pieces help with checking fit before installation and with comparing old and new parts during a rebuild. This makes the set useful for planned servicing as well as for bringing an older chassis back into operating condition after drivetrain wear or gear damage. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
TA-01/02 Front Gear Case, 4WD spare parts, red
300050541€13.99
This spare parts set supplies the red front gear case components for TA-01 and TA-02 4WD models, giving repair and maintenance work the exact housing parts needed for the front transmission area. The A parts tree contains 14 pieces, making it a focused replacement set for restoring the original layout rather than a general assortment. The molded sections shown here cover the front gearbox housing area, with matching red parts that help separate this assembly from other chassis sections during workshop sorting. The set is intended for model servicing where a cracked case, missing section or worn mounting point needs replacement with the correct designated parts. Included metal pins add the small hardware required for the assembly, so the gearbox section can be rebuilt with the supplied connecting elements from this pack alone. On the bench, the clearly grouped A parts support a straightforward check of each housing section before installation. For ongoing TA-01/02 upkeep, this set suits planned maintenance, accident repair and the restoration of older 4WD chassis that need the original front case structure in red. Warning! Not suitable for children under 14 years.
Gears & motor pinions
TA-01/02/DF-01 Ball Diff. Unit, RC spare part
300053070€43.99
The TA-01/02/DF-01 Ball Diff. Unit is a dedicated RC spare part for compatible TA-01, TA-02 and DF-01 chassis, bringing the differential section back into working order with a matching replacement assembly. As a ball differential, it is intended for the drivetrain, where controlled internal movement helps manage how drive is transferred through the gearbox during running. The set is supplied as 1 ball differential with 8 pieces, giving the core parts needed for this specific maintenance job rather than a mixed assortment of unrelated hardware. The accompanying assembly information refers to ball differential grease during installation, showing that this unit is built as a serviceable mechanical component rather than a sealed module. Documented elements such as the differential spur gear, gearbox joint, hexwrench steps and placement notes point to a structured assembly sequence with attention to part orientation. That makes the unit relevant for repair benches, rebuild projects and routine drivetrain upkeep on older compatible chassis. In workshop use, the unit fits naturally into a maintenance cycle that includes inspection, replacement of worn drivetrain parts and reassembly of the gearbox area. For existing TA-01, TA-02 or DF-01 models, it provides a direct route to keeping a compatible chassis in running condition with the correct differential format. Warning! Not suitable for children under 14 years.
Axes & drive shafts
TA-01/02/FF-01 C-Parts, rear upright spare set
310005377€12.79
The TA-01/02/FF-01 C-Parts rear upright set is a chassis-specific spare for compatible Tamiya models, supplying the moulded parts needed in the rear upright area on a single black sprue. For repair, maintenance or a careful rebuild, the matched layout keeps related pieces together and ready for selection at the bench. The injection-moulded frame holds several components in their original positions until removal, which helps preserve part identification during preparation and fitting. Mirrored shapes for left and right assembly can be checked before cutting from the runner, reducing mix-ups when replacing worn or damaged suspension-side parts. The sprue format also supports clean storage between repair sessions, since unused pieces remain attached and easier to track than loose small parts. Visible moulded markings on the runner further reflect its role as a functional service part for model maintenance. This spare set fits situations where a compatible chassis needs renewed rear upright components after use, damage or a missing part in a long-running build. It also suits keeping a dedicated replacement sprue on hand for workshop stock, so servicing can stay focused on the exact chassis section rather than replacing unrelated assemblies.
Other spare parts & accessories
TA-01/02/FF-01 D-Parts Body Mount Set
300050482€9.59
This D parts body mount set is made for TA-01, TA-02 and FF-01 model platforms and supplies the core hardware used to position and secure a bodyshell on the chassis. The 22-piece pack combines molded mounting parts with the small metal fixings needed for installation, making it a practical replacement when original body supports are missing, damaged or worn. The set contains 4 long upright posts with a row of adjustment holes, 2 angled mounting arms, 6 screws and 10 metal body clips. That layout supports the usual body-post setup used on compatible on-road chassis, where the shell sits over the posts and is locked in place with clips through the selected holes. The multiple hole positions allow the shell to sit at the required height for the specific bodyshell and mounting point arrangement already on the model. The angled brackets provide the base connection between the posts and the chassis structure. Used during repair, restoration or routine maintenance, this spare parts set helps return a TA-01, TA-02 or FF-01 build to a complete mounting setup. It also suits workshop stock for keeping compatible chassis ready for shell changes, rebuilds and replacement of lost clips or screws after running sessions. Warning! Not suitable for children under 14 years.
Axes & drive shafts
TA-01/02/TB-01/02/TG Wheel Axle Set, RC spare part
300050808€12.79
This RC spare part set supplies 2 metal wheel axles for compatible TA-01/02, TB-01/02 and TG chassis, giving a direct replacement option where a 39 mm axle is specified. The machined shape combines a threaded end, a cross-hole and a slotted coupling section, so the part matches the connection points used in these model vehicle platforms. The 39 mm format is the key reference for installation planning and parts matching. The pair layout supports side-to-side replacement with matching hardware rather than mixing old and new axle parts. The metal construction shown in the data suits a mechanical role where rotation, fastening and drivetrain connection meet in one compact component. Because the set is defined for TA-01/02, TB-01/02 and TG chassis, the copy stays focused on those stated applications only. In workshop use, this axle set suits routine maintenance, repair after wear, or restoring a compatible chassis to running condition with the specified part format. The 2-piece scope of delivery keeps the contents clear for parts drawers, bench stock and planned service work on supported RC models. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
TA-01/DF-01 Chassis, RC chassis spare part
300335100€23.99
The TA-01/DF-01 Chassis is a molded replacement chassis section for compatible RC model builds, providing the main structural base for reworking a worn frame or completing a repair with the correct platform shape. Its black molded construction uses a ribbed interior layout and a honeycomb reinforcement pattern, giving the part a defined geometry for mounted assemblies while keeping the form focused on mechanical function. The underside shows multiple screw bosses, fastening holes and raised perimeter walls that help position matching components at fixed points across the chassis. An oval cutout on one side and fork-like extensions at the opposite end are integrated into the molding, showing that this is not a generic plate but a chassis section shaped for a specific TA-01/DF-01 layout. The glossy finish comes from the molded surface itself, while the internal bracing and recessed sections are designed around fitment and support. As a spare part, it suits restoration work, replacement after damage, or keeping a compatible workshop build in running condition. On the bench, the chassis gives a clear base for reinstalling drivetrain and mounted hardware in their intended positions. In an ongoing RC collection, it also serves as a practical replacement part for maintaining older compatible models rather than leaving a build incomplete. Warning! Not suitable for children under 14 years.
Axes & drive shafts
TA-01/DF-01 Upright (2), RC spare part, black
300445572€8.69
TA-01/DF-01 Upright (2) is a black RC spare part set for compatible TA-01 and DF-01 chassis builds, supplying 2 mirrored uprights on a single molded sprue for direct replacement work. The paired form supports left and right side installation, making it easier to restore the original mounting layout when an existing part is worn, cracked or missing. Each upright is injection-molded and shaped with cylindrical mounting sections, angled arms and reinforcing ribs that support the part where screws or pins pass through the fixing points. The molded geometry is designed for chassis assemblies that rely on precise alignment between connected components, so replacement with the correct upright helps maintain clean mechanical fit. The central sprue keeps both matching pieces together until installation and helps identify the set as one complete replacement pair. This spare part suits workshop use during routine maintenance, rebuilds after running wear, or parts-box preparation for TA-01 and DF-01 platforms. Kept on hand with other service components, the 2-piece set supports faster repairs when suspension or wheel-mount areas need attention. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
TA-01/TA-02 B-Parts, gearbox rear parts set
300005575€18.99
This replacement parts set is made for the rear gearbox section of TA-01 and TA-02 based models and comes as a black molded B-parts sprue with 7 individual components. The layout keeps related pieces together on one tree, making it easier to identify the required shapes during maintenance or a focused rebuild of the drivetrain housing area. The stated compatibility references 58136, 58146 and 58154, giving clear model numbers for checking an existing build before fitting. As a dedicated B-parts set, this pack suits repairs where the original rear gearbox components are damaged, incomplete or no longer usable. The black finish matches the supplied parts designation, while the molded format supports clean separation of each piece during assembly. The included contents are 1x B parts tree with 7 parts. On the workbench, this set supports targeted servicing without replacing unrelated sections of the chassis. It fits naturally into a repair routine that starts with model-number checking, then moves to part removal, sprue separation and installation in the rear gearbox area of the compatible TA-01 or TA-02 build. Warning! Not suitable for children under 14 years.
Gears & motor pinions
TA-02 Gear Set, RC spare part, 15-piece drivetrain
300050529€12.99
The TA-02 Gear Set is a dedicated RC spare part set for transmission repair, built around the updated gear layout shown for this drivetrain. Its 15 included pieces support service work on compatible TA-02 based models, with the main revision centered on a one-piece molded spur and drive gear that replaces the earlier separate parts arrangement. This change brings the large spur gear and the smaller drive gear together in a single repair component, so the transmission uses the revised integrated format specified for this set. The package also uses an idler gear in resin instead of the earlier metal version, and the ball retainer specification is G4. These details matter when replacing worn internal drivetrain parts, because the set is designed around that exact update rather than a generic mix of gears. The scope of delivery is 1 gear set with 15 pieces. On the workbench, the set suits planned transmission overhauls as well as targeted replacement of worn gear components after regular RC running. It is intended for compatible TA-02 applications and is not compatible with 1/10 R/C off-road buggies, making the fit context clear before installation begins. Warning! Not suitable for children under 14 years.
Axes & drive shafts
TA-02/CC-01/FF-01 Front Upright Pair, RC Spare Part
300050705€7.29
This spare part set is made for TA-02, CC-01 and FF-01 chassis and supplies 2 black front uprights for the steering end of the front axle. The mirrored left and right layout supports a matched fit during repair work and helps restore the intended geometry at the front wheel mounting points. Each upright is moulded with a circular hub opening, fastening holes and a reinforced arm section that connects into the surrounding steering hardware. The ribbed structure adds material where the shape changes direction, while the drilled connection points support accurate screw-based installation with the corresponding chassis parts. As a dedicated replacement part, the set focuses on the front upright area rather than a universal fit across unrelated platforms. The pair suits routine maintenance, rebuilds after wear, or the completion of an older TA-02, CC-01 or FF-01 chassis project. In workshop use, the 2-piece set makes it possible to replace both front sides together and keep the steering assembly consistent across the axle. Warning! Not suitable for children under 14 years.
Axes & drive shafts
TA-02/FF-01 Front Upright, spare part, blue
300445246€8.69
The TA-02/FF-01 Front Upright blue set supplies 2 replacement uprights for compatible front-end assemblies. Each part is formed as a mirrored counterpart, so the left and right sides can be positioned correctly when restoring the steering or suspension layout on a TA-02 or FF-01 chassis. The shape combines a large cylindrical hub section with a smaller upper mounting point and a flat arm with a fastening hole. Reinforcing ribs add structure to the moulded form, and the visible metal insert at the upper mount provides a ready fixing point within the assembly. The blue colour helps separate this pair from other small chassis parts during sorting, servicing and rebuild work. As a dedicated spare part, this set is intended for precise replacement rather than general-purpose adaptation. The 2-piece format suits routine maintenance, repair of worn front components or keeping matching replacements on hand for workshop use. In a build area or pit box, the mirrored pair can be checked against the existing front assembly before fitting, helping keep the chassis layout consistent on both sides. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
TA-05/TB Evo.IV B-Parts Body Mount Set
300051242€15.99
The TA-05/TB Evo.IV B-Parts Body Mount set provides the dedicated mounting components used around the body support area on compatible chassis. With 12 black moulded parts in one pack, it covers the component group needed when the original posts, braces or mounting pieces need replacement during maintenance or rebuild work. The set is listed as B parts and is supplied as 1x parts pack, which helps keep chassis servicing focused on the exact section rather than replacing unrelated hardware. Visible components include upright body posts with a series of adjustment holes, shaped brackets, reinforcing plates and small spacers. That layout supports precise positioning where shell height or mounting alignment needs to match an existing setup on a TA-05 or TB Evo.IV platform. This kind of parts set suits workshop stock for routine RC upkeep, accident repair or the completion of an unfinished chassis section. It can be used when restoring the original mounting arrangement after wear, damage or missing hardware, and it keeps the fit of the shell support area tied to the intended B-parts group for these model platforms. Warning! Not suitable for children under 14 years.
Gears & motor pinions
TA-05/TB-03 Drive Shaft, metal spare part, 45 mm
300051216€11.99
The TA-05/TB-03 Drive Shaft 45 mm is a metal spare part for compatible Tamiya chassis setups, with 2 matching shafts supplied for drivetrain service on FF-03 chassis, FF-03 PRO chassis, TA05 Ver.II and TA05. The 45 mm length gives a clear fit reference when a build or repair calls for this exact shaft size. Each shaft uses a straight rod form with ball ends and cross pins, a layout designed to connect with the surrounding drivetrain hardware in the intended mounting points. The metal construction and polished finish give the part a clean technical look while keeping the focus on mechanical function inside the chassis. As a dedicated replacement component, it suits maintenance work, parts refreshes and like-for-like swaps where the named platforms require this specific format. In workshop use, the 2-piece set supports planned servicing or the replacement of worn drivetrain hardware on one of the listed chassis types. Kept alongside other RC spares, the clearly stated compatibility and 45 mm dimension make this part easy to identify before installation. Warning! Not suitable for children under 14 years.
Axes & drive shafts
TA-05IFS D-Parts, RC chassis suspension arms
300051297€10.99
TA-05IFS D-Parts is an RC chassis spare parts set with 4 molded suspension arms arranged as 2 front and 2 rear pieces. The wishbone-style shape, mounting holes and central attachment points support correct installation on compatible touring car platforms and restore the intended suspension layout after wear or impact damage. The scope of delivery contains 1x D parts tree with 4 parts. These black molded components are intended for replacement and maintenance work rather than universal use, so the value lies in exact fit across the listed chassis families. Compatibility covers FF-03, FF-03 PRO, TA06 MS, TA06, TA06 PRO, TA05 ver.II, TB-Evo.7, TB-Evo.6 MS, TB-Evo.6, TB-05 PRO, TB-04, TB-04 PRO, TB-03, TB-03 VDS, TRF419XR, TRF419X, TRF419, TT-02 TYPE-SR and TT-02 TYPE-S. That broad fit list makes the set useful in a spares box for racers and builders maintaining more than one platform. During workshop servicing, replacement arms like these help return free suspension travel and proper linkage alignment on the compatible chassis. They also suit planned rebuilds where fresh running gear parts are fitted before the next track session. Warning! Not suitable for children under 14 years.
Other spare parts & accessories
TA-05IFS/TB-03 F-Parts Hub Carrier (2), chassis part
300051293€7.79
The TA-05IFS/TB-03 F-Parts Hub Carrier set supplies 2 matching chassis components for RC model maintenance, rebuilds and parts replacement. Shaped as front F parts, these pieces are intended for the front area of compatible on-road platforms, where correct mounting points and part geometry matter for a clean fit during service work. Compatibility covers a wide range of Tamiya chassis: FF-04 EVO, FF-03, FF-03 PRO, TA06 MS, TA06, TA06 PRO, TA05 Ver.II, TB-Evo.6 MS, TB-Evo.6, TB-05 PRO, TB-04, TB-04 PRO, TB-03, TB-03 VDS and TT-02 TYP-S. The scope of delivery contains 1 F parts set with 2 components. That broad fitment makes the set useful as a replacement kept alongside regularly used touring car spares, especially when one workshop supports several chassis generations. During routine maintenance, crash repair or a full chassis refresh, a matched pair helps restore the intended front assembly with the correct left and right quantity already in the pack. The black molded parts shown for this set focus attention on fit and function rather than decoration, making them a straightforward choice for keeping compatible RC chassis ready for the next build session or track run. Warning! Not suitable for children under 14 years.
Gears & motor pinions
TA-06 Rear Gear Diff. Case Set 52T Spare Part
300051462€4.79
The TA-06 Rear Gear Diff. Case Set 52T is a dedicated spare part for compatible Tamiya chassis, built around a rear bevel gear differential housing layout that supports accurate servicing of the drivetrain. With 7 pieces in the set, it provides the core parts needed for replacing the rear diff case assembly when wear, damage or a rebuild calls for fresh components. This set is specified for TA06, TA06 PRO, TA06 MS, XV-01, XV-01 PRO, XV-01T, M-07 CONCEPT, M-08 CONCEPT and FF-04 EVO chassis. It also fits TD4 and TD2 chassis when used with 54471, which makes the compatibility scope especially useful for hobby benches handling several platforms. The black moulded parts shown for the assembly use multiple fastening points and a separate cover section, supporting a clean mechanical fit around the differential area. On a maintenance bench, the set helps restore a worn rear transmission section with chassis-specific parts instead of improvised substitutes. During a rebuild, the 52T case format and rear mounting design support a focused replacement job for the differential housing section while keeping the chassis setup aligned with the listed applications. Warning! Not suitable for children under 14 years.
Axes & drive shafts
TA02 D-Parts Suspension Arms, RC spare parts
310555091€18.79
TA02 D-Parts Suspension Arms bring core running gear pieces together in one replacement set for RC chassis maintenance. The black molded sprues show mirrored suspension components, linkage-style parts and smaller inserts, giving a clear starting point when worn or broken originals need to be swapped out. The sprue layout keeps related shapes organised before removal, which helps when matching left and right side parts during a repair. Large A-arm style pieces sit alongside long narrow bars with multiple mounting points, plus smaller lever-like forms and circular bush-style elements. This mix supports detailed work on suspension-related areas rather than general cosmetic changes. The molded numbering on the runners also helps identify individual sections during parts preparation and fitment. On the bench, this set suits routine chassis upkeep, restoration of older TA02-based builds and replacement after hard running sessions. It also works as a practical spare to keep in a workshop drawer, ready for rebuilds that call for original-style suspension hardware and linked structural pieces.
Gears & motor pinions
TA05 IFS Ver.II Spur Gear, RC spare part, 70T M0.6
300051215€6.29
The TA05 IFS Ver.II Spur Gear is a dedicated RC spare part for drivetrain service on selected Tamiya chassis. With 70 teeth and module 0.6, this main gear is built for transmission use where the gear ratio and tooth format must match the existing layout, making it a focused choice for repair or planned parts replacement. The component is supplied as 1 main gear 70T and is shown as a black molded gear with a fine outer tooth ring, a large center hole and multiple evenly spaced inner holes. That geometry matters during maintenance because the mounting pattern and hub area have to align with the drivetrain hardware already in the chassis. Compatibility is stated for TD4 chassis, TD2 chassis, TA08 PRO chassis, TA05 Ver.II chassis and TA05, which keeps selection tied to named platforms rather than broad guesswork. On the bench, this gear suits routine transmission refreshes, rebuilds after wear, or a direct swap when a matching 70T M0.6 part is needed for one of the listed chassis. The single-part scope also keeps the replacement straightforward when an existing drivetrain setup is being restored with the same specification rather than changed to a different ratio. Warning! Not suitable for children under 14 years.
Gears & motor pinions
TA08 06 Module Spur Gear 71T, RC spare gear
300051667€3.69
The TA08 06 Module Spur Gear 71T is a drivetrain spare part for TA08 chassis cars, built to replace a worn gear with the same 06 module format and 71T tooth count. In the transmission, the spur gear works directly with the pinion gear to pass motor power into the driveline, so a fresh gear can restore clean meshing where wear has built up over time. The part shown has a black moulded finish, a large centre hole and multiple circular cut-outs around the hub. Those openings are part of the gear design and sit around the central mounting area while the fine outer teeth carry the load of the gear mesh. Used as routine maintenance, this replacement helps keep the chassis in running condition when the original gear shows visible wear on the teeth. The pack contains 1 TA08 06 Module Spur Gear 71T. It suits workshop upkeep between running sessions, whether the transmission is being refreshed after repeated use or a worn gear is being swapped before the next outing. For TA08 owners who keep spares on hand, this gear covers a core wear point in the drivetrain with the exact compatibility stated for TA08 chassis cars.
Axes & drive shafts
TA08 A Parts Steering Arm Pully RC Spare Set
310015144€14.49
TA08 A Parts Steering Arm Pully 58693 is a replacement parts sprue for RC model maintenance, centred on steering arm and pulley components that restore key chassis functions on the intended TA08 build. The black moulded frame presents the parts in a clearly organised layout, with each piece held in place until needed at the workbench. The runner carries a mix of larger structural shapes and smaller fitting pieces, including arm forms, ring elements and compact mounting details that belong together within the same assembly area. Moulded reference marks with the letter A and numbers 1 through 14 are visible on the sprue, giving a direct visual guide when matching each section to the required build step or service task. This format helps separate similar-looking pieces before cutting and supports a tidier repair process when a worn section needs replacement rather than a full rebuild. On a maintenance bench, the grouped layout makes it easier to prepare the required sections before installation and keep unused pieces together until later service work. For ongoing chassis care, a dedicated replacement frame like this helps return the matching model to proper mechanical condition with the correct part shapes kept in one set.
The best selection of RC spare parts
Whether you're looking to upgrade your RC model or repair it after an action-packed run – in our RC spare parts category, you'll find everything you need. Tamiya offers a wide range of high-quality spare parts for your RC models. Our spares cover all essential components to ensure your model is always in top shape.
Spare parts for RC cars: variety for every model
Our RC spare parts are specifically designed to enhance the performance and lifespan of your model. The range includes everything from steering knuckles, drive shafts, and control arms to ball joints and leaf springs. With over 400 different items, we offer everything a hobbyist could wish for. Whether you're searching for spare parts for RC cars or specific components like axle housings or oil dampers – you’ll find it here.
Why RC spare parts are important
No RC model can run without the right spare parts. RC spare parts not only ensure that your model is always ready for action but also boost performance and improve durability. Whether you need spare parts for RC cars or specific components like axles and gearbox protectors – regular maintenance and the replacement of worn-out parts are key to an optimal driving experience. With the right RC car spare parts, you can ensure that your model stays in top condition, allowing you to enjoy the full driving experience.
The benefits of Tamiya RC spare parts
When you choose Tamiya RC spare parts, you're opting for quality and precision. Each of our spare parts is perfectly matched to our models and offers the highest reliability. Thanks to high-quality materials and precise manufacturing, you can be sure that your model building project will always deliver the best performance. Whether you're just starting out in RC model building or you're an experienced hobbyist – Tamiya RC spare parts guarantee quality you can feel.
Browse through our RC spare parts shop
Explore our extensive range of RC spare parts and get your model back in top form. In our RC spare parts shop, you'll find everything you need to maintain, repair, or improve your vehicle. From beginners to professionals – we have the right RC car spare parts to take your model building to the next level.