Other spare parts & accessories

10mm Shim Set, RC accessory, 0.1-0.3 mm spacers

€13.49

This 10 mm shim set brings fine mechanical adjustment to RC chassis work, with 30 spacers sized at 10 mm inner diameter and 13 mm outer diameter for controlled spacing at shaft mounting points. The 3 thickness options of 0.1 mm, 0.2 mm and 0.3 mm make it possible to correct small gaps that can lead to unwanted movement in suspension or wheel axle assemblies. Instead of relying on a single washer size, the set gives stepped tuning options that suit different setup needs across on-road and off-road vehicles. Each shim can be placed to shift the position of a mounted part in small increments, including forward adjustment where the chassis layout calls for tighter spacing. That makes the set useful during maintenance, rebuilds and race-focused setup changes where alignment and reduced slippage matter. Scope of delivery: 1 spacer set with 30 pieces. On the bench, the assortment supports careful fitting of moving parts before a run. During a rebuild or handling-focused setup session, the different shim thicknesses help dial in cleaner spacing at the exact point where play needs to be reduced.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

12 mm Wheel Hub Hexagon Set, RC chassis accessory

€10.59

This 12 mm wheel hub hexagon set brings a clean aluminium upgrade to the wheel mounting area on a wide range of RC chassis. The pin-type design pairs each hex hub with a matching pin, creating the interface that transfers drive from the axle to the wheel while keeping the fit consistent during assembly, maintenance and parts replacement. The scope of delivery includes 4 wheel hub hexagons and 4 pins. The aluminium construction gives these small drivetrain parts a crisp machined look, and the 12 mm hex format matches the standard wheel mounting size used across many compatible on-road and off-road platforms. Fitment listed in the data covers CR-01, DF-03, DF-02, DT-03, DT-03T, DT-02, F103GT, M-06, M-06 PRO, M-05, M-05 PRO, M-05 ver.II PRO, MF-01X, TT-02B, TT-02FT, TT-02RR, TT-02D, TT-02 TYPE-SR, TT-02 TYPE-S, TT-02, TT-01D TYPE-E and TT-01 TYPE-E chassis. For workshop stock, rebuilds or replacing worn wheel mounting parts, this set covers one full chassis with 4 matching hubs and pins. It suits bench work where exact chassis compatibility matters and keeps the wheel mounting hardware aligned with the specified 12 mm standard used by the listed platforms.  Warning! Not suitable for children under 14 years.

Gears & motor pinions

19T Pinion Gear, model accessory, M0.6

€5.69

This 19T pinion gear is a compact drivetrain part for model applications that use module M0.6 gearing. Its 19 straight teeth mesh with the matching gear stage to pass motor rotation into the transmission, making it a functional choice when a specific tooth count is needed in the drive layout. The dark metal gear body is shaped for shaft mounting, with a central round bore and a side set-screw hole visible on the part. The top surface is marked with 19, which helps distinguish this version from other tooth counts during maintenance or parts sorting. As a small mechanical component, the pinion sits at the point where motor output meets the rest of the drivetrain, so the tooth count directly relates to the gearing combination used in the model. It fits naturally into workshop tasks such as replacing a worn pinion, restoring a compatible drivetrain, or keeping a matching spare ready for service intervals. On the bench, the compact form and visible marking make it straightforward to identify alongside other transmission parts and gearing options.  Warning! Not suitable for children under 14 years.

Gears & motor pinions

20/21T Pinion Gear Set, RC motor accessory, aluminum

€9.99

This 20/21T Pinion Gear Set is a compact drivetrain upgrade for compatible RC chassis, pairing 2 aluminum pinions with 2 grub screws for secure mounting on the motor shaft. The 20-tooth and 21-tooth options give a clear gearing choice when replacing worn parts or adjusting the drive layout for a specific chassis setup. The machined aluminum construction keeps the focus on precise tooth engagement and clean fitment in model drivetrains that use module 0.6 gearing. One pinion is marked 20 for quick identification during setup, which helps separate the two ratios at the workbench. The set is intended for a wide spread of Tamiya platforms including M-05, M-05 PRO, M-05 ver.II PRO, M-06, M-06 PRO, WR-02, WR-02G, WR-02CB, GF-01, GF-01TR, GF-01CB, G6-01, G6-01TR and TB-05 PRO. It also supports CC-01 with 20T only, plus TA06, TA06 PRO, TA06 MS and TC-01 with 21T only. Additional chassis-specific notes are defined for several applications: DF-02 is used with 53703, F104PRO II is used with 51609, and TA07 MS is used with 51356, 51423 and 51548. That makes the set a practical spare or tuning part for keeping compatible RC cars running with the correct motor pinion combination.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

2mm C-Ring-Set, model accessory, 8-piece

€2.19

This 2 mm C-Ring-Set supplies 8 matching retaining clips for model maintenance, repair work and parts replacement. The compact format suits assemblies that use small fastening points, where a C-shaped ring locks into a groove on a shaft or similar mounting point to hold parts in position. The set groups identical metal clips together, which helps when a rebuild calls for consistent replacement parts rather than mixed hardware. The open centre cutout allows each ring to snap into place on the intended fitting, making this type of fastener useful wherever a low-profile retainer is needed in a mechanical model assembly. The silver-coloured finish also makes the pieces easy to identify in a parts tray or workshop setup alongside screws, washers and other small hardware. Used as spare parts, these C-rings support routine servicing, careful restoration work and the replacement of missing retainers in existing builds. Kept in a hobby drawer, the 8-piece pack provides a practical stock of matching clips for future workshop tasks on compatible model mechanisms.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

2mm E-Ring Satz, model accessory, 15 pieces

€3.09

This E-Ring Satz provides 15 matching retaining clips in a 2 mm size for model maintenance, repairs and mechanical assembly work. Each E-ring is made as a small stamped metal fastener that presses onto a grooved shaft or axle from the side, where it acts as a stop to hold mounted parts in place. The flat clip profile keeps the fastening point compact, which is useful in tight spaces around driveline and wheel assemblies. The pack suits jobs where worn or missing retaining hardware needs a direct replacement in the correct size. A 2 mm E-ring can be used wherever the assembly calls for this specification, including axle or shaft setups that carry gears, bushings or wheels. The 2 mm thickness stated in the data adds a clear reference point when matching spare hardware to an existing build. With 15 identical pieces in one set, the supply supports repeated service work and keeps consistent hardware ready for future rebuilds. On the workbench, these clips fit naturally into parts sorting trays, spare hardware boxes and routine maintenance kits for RC and scale model projects. They are especially useful when a rebuild calls for several matching retainers across multiple connection points or when a small clip needs quick replacement after disassembly.  Warning! Not suitable for children under 14 years.

Screws & ball head screws

2mm/M2 Lock Nut Mini 4WD hardware set

€4.99

This hardware set brings 10 compact M2 lock nuts into Mini 4WD maintenance, repair and fresh assembly work. The 2 mm format suits small threaded connections, while the lock-nut construction with a nylon insert ring is designed to hold more firmly once tightened, a useful detail on fast-moving model assemblies where vibration can work against standard fasteners. The close-fitting hex shape supports careful tool use on small parts, and the metal finish gives each nut a clearly defined edge during installation. Keeping matching M2 hardware together also helps maintain a consistent fit across repeated rebuilds, part swaps and setup changes. Because the pack contains 10 pieces, it covers multiple fastening points and leaves spares ready for later workshop use. The set is focused, simple and specific: small fastening hardware for Mini 4WD systems where the right thread size matters. On the bench, these lock nuts suit routine replacement after wear, rebuilding a chassis with fresh hardware, or keeping spare fixings ready in a parts box between race-day adjustments. They also fit neatly into a regular stock of model workshop essentials, alongside the screws, shafts and brackets used in ongoing Mini 4WD upkeep.  Warning! Not suitable for children under 14 years.

Screws & ball head screws

2x8mm Differential Tapping Screws, model spare set

€3.29

This spare screw set focuses on one specific workshop need: 10 matching 2x8 mm differential self-tapping screws for compatible model maintenance and repair. The uniform size keeps replacement work consistent when original fasteners are worn, missing or set aside during a rebuild, and the metal construction suits repeated use in model assembly tasks where a precise screw type matters. The domed heads use a crosshead drive, allowing the tool to seat cleanly during installation and removal. A fully threaded shaft is suited to fastening duties where the thread needs to bite along the full length of the screw rather than only near the tip. Because all 10 screws share the same format, the set supports organized parts storage and avoids mixing unmatched hardware into a differential assembly. The pack contents are stated plainly: 10 differential self-tapping screws. On the bench, this set fits naturally into routine servicing, replacement of lost fasteners, or preparation of spare hardware before a rebuild begins. It also works as a practical stock addition for model toolboxes and parts drawers, where a clearly defined 2x8 mm screw can save time during maintenance on compatible assemblies.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

37mm SwingShafts, RC spare part for XV-02

€16.19

These 37 mm SwingShafts are a focused RC spare part for keeping compatible chassis setups running cleanly and consistently. Designed for the XV-02 chassis, they replace worn swing shafts in the assembly universal area, where accurate fit and free movement matter to drivetrain response and stable operation during repeated running sessions. Each shaft is marked A • 37 and the set supplies 2 matching parts for the same specified length. The black rod form with metal inserts at both ends reflects the compact mechanical role these parts play inside the chassis assembly. On TT-02 based cars, the shafts can also be used alongside Item 54623 and 51444 for defined compatibility. Combined with Item 54874, they also allow a wider camber angle adjustment range on the TT-02 chassis, opening more setup latitude for fine tuning suspension geometry. This kind of replacement suits regular workshop maintenance, rebuilds after heavy use, or planned setup changes between chassis configurations. In a tuning session, fresh shafts can restore precise movement in the relevant assembly area, while in a parts box they serve as a chassis-specific option for XV-02 and selected TT-02 builds.

Axes & drive shafts

39mm Drive Shaft Set, RC spare part for TT-01E

€12.99

This RC spare part set provides 2 drive shafts in a 39 mm format for selected Tamiya chassis. Designed for TA-01, TA-04, TA-05 and TT-01E platforms, the shafts sit in the drivetrain where rotating assemblies need a compact link that can keep transmitting power while suspension parts move through their travel. Each shaft uses a straight center section with rounded ends and cross pins, a dogbone-style layout commonly used to connect outdrives and wheel-side drive components. That shape allows the shaft to articulate inside the drivetrain rather than acting as a fixed rod, which matters when a chassis is cornering, accelerating or running over uneven surfaces. The 39 mm dimension is the key fit point here, so matching the stated length is essential when replacing worn or missing drivetrain parts. Supplied as a 2-piece set, the pack suits paired servicing work without forcing a mixed left and right setup. In workshop use, these shafts fit naturally into rebuilds, maintenance sessions and parts-box planning for compatible touring car chassis. They also make sense as a trackside spare when a running session calls for a quick drivetrain refresh on TA-01, TA-04, TA-05 or TT-01E based models.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

3mm 5.5x5.0mm Spacer, model accessory, 10-pack

€8.19

This spacer set is built around exact measurements that matter during model maintenance and parts replacement. Each piece is specified at 3 mm with 5.5 x 5.0 mm dimensions, giving a clear reference for assemblies that rely on this format to maintain the intended spacing between compatible components. The set contains 10 matching spacers, which supports repeated service work without mixing different sizes in the same build. The defined dimensions make this set useful when an existing assembly already calls for 3 mm spacers and when consistent fit across several mounting points is needed. Rather than relying on approximate sizing, the stated 5.5 x 5.0 mm format gives a direct basis for checking compatibility against the parts already in use. On the workbench, these spacers suit routine maintenance, measured replacement and keeping spare hardware ready for future adjustments. The 10-piece count also helps when several identical positions in one assembly need the same spacer size, or when matching replacements are kept in reserve for later servicing.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

3mm O-Ring black, model accessory, 10-piece

€1.99

This 10-piece pack of black 3 mm O-rings adds a practical spare-parts supply for model maintenance, repair work and small mechanical assemblies. Each ring shares the same compact diameter and circular form, making the set useful wherever a matching seal or replacement ring is needed to restore fit between moving or joined parts. The pack contains 10 identical rubber O-rings, which helps keep replacements consistent across repeated service jobs instead of mixing unmatched sizes. Their black finish makes them easy to distinguish from other small workshop parts during sorting and storage. In model building and accessory upkeep, small sealing components often matter as much as larger visible parts, especially when a worn ring needs a direct like-for-like swap rather than an improvised substitute. Kept in a parts drawer, tool case or bench organiser, these O-rings are ready for routine maintenance sessions and quick repairs. The uniform 3 mm format also suits builders who prefer to keep duplicate consumable parts available before starting detailed assembly or servicing work.  Warning! Not suitable for children under 14 years.

Screws & ball head screws

3mm Washer MA14, model accessory, 15-piece set

€3.09

This MA14 washer set brings a straightforward supply of 15 matching 3 mm washers to the workbench, supporting model maintenance, replacement tasks and assembly jobs that call for correctly sized small hardware. The compact format suits builders who need a ready reserve for routine parts handling rather than a mixed assortment. Each washer is identified in the data as 3 mm Washer and grouped under Models Supplies, placing it clearly in the spare-parts and workshop-accessory side of model building. The 15-piece count gives a practical quantity for keeping common hardware on hand during repairs or when an existing build needs fresh fastening components. The MA14 reference helps distinguish this set from other small parts in a broader workshop stock, especially where several washer sizes may be stored together. On the bench, a dedicated washer pack like this supports cleaner preparation before assembly starts and quicker replacement when a small part is missing during maintenance. It also fits neatly into organised spares storage, where size-specific hardware can be sorted by reference and reached quickly for the next build session.

Other spare parts & accessories

3x0.7mm Aluminum Spacer Set, model accessory

€6.29

These aluminum spacers in 3x0.7 mm format support accurate spacing in detailed model assembly, where a defined gap can influence fit, alignment and component position. The 10-piece pack gives a ready supply for workshop drawers, replacement needs or builds that use several matching spacers in one setup. The 3 mm size and 0.7 mm thickness make this set suited to fine adjustment work rather than broad structural filling. In model construction, spacers like these sit between mounted parts to create consistent separation and help maintain the intended position of screws, brackets or other fitted elements. Aluminum brings a clean, technical finish to this small but useful hardware format and fits naturally into precision-focused hobby work. Whether used during a fresh build, a repair or a measured setup change, the defined dimensions make selection straightforward when a specific spacing value is needed. Kept in a parts box or bench organizer, the set adds a practical option for builders who work through detailed fitting tasks one measured step at a time.  Warning! Not suitable for children under 14 years.

Screws & ball head screws

3x10 Tapping Screw BK, model screw set, 10 pcs

€6.19

This screw set supplies 10 black 3x10 tapping screws for model assembly, replacement work and workshop stock. The compact format suits builders who need the exact fastener type stated on a parts list or want matching hardware ready for routine maintenance on compatible models. The 3x10 specification gives a direct reference for size, which helps when sorting spare hardware for repairs or preparing parts before a build begins. The black finish supports a uniform appearance on visible fixing points where darker hardware is preferred. As tapping screws, these fasteners are intended for fastening duties in suitable model applications where this screw type is required. The pack count of 10 pieces provides a practical quantity for replacing missing screws, refreshing used fixings or keeping a small reserve in the workshop. On the bench, this set fits naturally into regular maintenance tasks such as securing parts after disassembly or replacing worn hardware during a rebuild. It also works well as a dedicated spare pack kept alongside model tools and sorted fasteners, ready when the correct 3x10 tapping screw is needed.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

3x10mm Alum. Turnbuckle Shaft, chassis accessory

€11.99

These 3 x 10 mm aluminium turnbuckle shafts bring precise anti-roll bar adjustment to compatible chassis setups while adding a clear blue finish to the hardware. The set contains 4 shafts and is intended as a chassis accessory for fine tuning left and right anti-roll bar settings without removing the adjuster. The compact 3 x 10 mm dimensions suit dedicated on-road racing platforms where small setup changes matter. As a replacement for 9804250, this set gives a direct route to refreshing existing hardware with the same stated function. Compatibility is listed for TRF415MSX, TRF415MS, TB Evo. IV MS and TB Evo. IV. TA05 fitment is also specified, with the condition that adjusters must be shortened. At the workbench, these shafts support quick setup changes between runs when anti-roll bar balance needs a finer response. In regular maintenance, the 4-piece pack also helps keep a matching set ready for rebuilds, repairs or chassis-specific spares within a race box.  Warning! Not suitable for children under 14 years.

Screws & ball head screws

3x12mm Counter Screw, model screw set, 10 pieces

€3.29

This screw set provides 10 matching countersunk screws in a 3 x 12 mm format for model assembly, maintenance and hardware replacement. The flat countersunk head supports a flush finish on compatible parts, which helps keep surfaces even where protruding fasteners would interfere with fit or movement. The set is supplied as metal fastening hardware and suits tasks that call for the same stated size across several fixing points. A 12 mm length gives reach through compatible layered parts, while the 3 mm diameter defines the thread size for matching holes and receiving material. Because all 10 screws share the same format, the pack works well for replacing lost fasteners in groups rather than mixing different sizes during a repair. The pointed threaded shafts are shaped for fastening use, and the Phillips drive allows controlled tightening with a matching screwdriver. On the workbench, the set supports routine upkeep of model builds, spare-parts sorting and planned rebuilds where identical hardware is needed across several positions. It also fits neatly into parts storage for future service jobs, keeping a clearly specified screw size ready when a compatible assembly calls for 3 x 12 mm countersunk fixings.  Warning! Not suitable for children under 14 years.

Screws & ball head screws

3x12mm Steel CS HexHead Screws, model accessory

€2.79

These 3x12mm Steel CS HexHead Screws are a focused workshop accessory for maintaining compatible model and RC assemblies. The steel construction provides the specified material for replacement use, while the countersunk screw form is made to sit into matching recessed mounting points for a flush finish. Each screw uses a hex head, giving a defined tool interface for secure tightening during fitting and servicing. The pack contains 10 screws, which makes it useful for routine maintenance, repair work, or keeping matching fasteners ready in the parts box. The 3x12mm size is the key reference for checking compatibility with the intended assembly point, especially where the original build calls for the same thread and length. As replacement hardware, these screws are suited to restoring firm connections after wear, loss, or repeated disassembly during setup changes and repairs. On the workbench, they fit naturally into regular service tasks such as refreshing mounting points on a chassis, reattaching compatible sections, or replacing individual fasteners before the next run. For model builders who keep spare hardware sorted by size, this 10-piece set adds a clear, easy-to-store option for ongoing maintenance.  Warning! Not suitable for children under 14 years.

Screws & ball head screws

3x15mm Tapping Screw, model accessory, 10-pack

€3.39

This 10-pack of 3x15 mm tapping screws is a focused workshop spare for model maintenance, repairs and ongoing assembly needs. The exact 3x15 mm size gives a clear match point when worn, missing or damaged fasteners need to be replaced with the same format, and the TA-01 and TA-02 designation identifies the intended application directly in the part name. The set consists of 10 silver metal screws with a threaded shaft, rounded pan head and cross-head drive as shown in the product image. That head shape supports secure seating against the mounted part, while the cross-head recess allows controlled tightening with a suitable screwdriver. Keeping identical screws together in one pack helps maintain a consistent fit across the relevant fixing points instead of mixing different lengths or thread types during service work. On the bench, this kind of hardware is useful for routine chassis upkeep, replacing lost fasteners after disassembly, or keeping matching spares ready between rebuilds. For TA-01 and TA-02 based model work, the pack offers a straightforward way to restore the specified fixing point with the correct screw format.

Screws & ball head screws

3x22mm Screw Pin, model spare part, 4 pcs.

€4.29

This spare-parts set provides 4 matching 3 x 22 mm screw pins for compatible model assemblies, giving a direct way to replace fastening parts that are missing, worn or no longer holding as intended. The defined 22 mm length and 3 mm format help maintain the original connection points in builds that rely on this pin size. Each piece has a long cylindrical shaft, a rounded tip, a wide head and a ringed section below the head. That shape supports guided insertion and a seated hold in the matching mounting point, while the uniform dimensions across all 4 pieces keep the set consistent for repair work. The black finish gives the parts a neutral technical appearance that blends into many model layouts and spare-parts boxes. This 4-piece pack suits routine workshop upkeep, targeted repairs and the replacement of individual fastening points on compatible models. Kept alongside other maintenance parts, the pins are ready when a build needs a like-for-like fixing part in the 3 x 22 mm size.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

3x23mm Turn-Buckle Shaft, RC spare part, 4 pcs

€4.69

This set of 4 turn-buckle shafts in 3x23 mm format adds a precise replacement option for RC model maintenance and setup work. The metal shafts are threaded on both ends and use a compact central section that supports handling during installation, removal and adjustment inside a linkage assembly. Used in steering or similar connection points where exact length matters, turn-buckle shafts allow the assembly to be tuned by changing the effective linkage position rather than replacing the whole mechanism. The 3x23 mm specification is the key fit detail for matching an existing compatible build, and the pack of 4 provides a practical quantity for servicing paired linkage points or keeping matching spares on hand. The dark metallic finish and cleanly cut threads reflect the functional, workshop-focused character of the part. These shafts fit naturally into bench work such as replacing worn connectors, refreshing a running chassis or preparing a model for its next setup session. In a parts box, pit case or hobby drawer, a matched set of 4 helps keep compatible RC assemblies ready when a linkage needs a fast, like-for-like swap.  Warning! Not suitable for children under 14 years.

Screws & ball head screws

3x5mm Flathead-Screw, model screw set, Phillips

€2.89

This screw set supplies 5 matching 3 x 5 mm flathead fasteners for model building, maintenance and hardware replacement. The compact size and crosshead design make the screws easy to identify at the bench, while the flat head sits neatly against compatible parts for a clean, flush connection. Each screw has a Phillips-style drive and a short machine thread, as shown by the defined head shape and threaded shaft. That combination suits small fastening points where controlled tightening matters and where oversized hardware would interfere with surrounding parts. The set is useful when an original screw is lost during assembly, when worn hardware needs replacing, or when a matching group of fasteners is needed for a repair. The black finish keeps the hardware visually understated on many technical builds. On a workbench, these screws fit naturally into routine model care: securing a bracket, refitting a cover, or restoring a connection after disassembly. Kept alongside other spare hardware, the 5-piece pack provides a practical reserve for compatible model sections that call for the same 3 x 5 mm format.  Warning! Not suitable for children under 14 years.

Screws & ball head screws

3x6mm Steel CS HexHead Screws, model hardware

€2.89

These 3x6mm Steel CS HexHead Screws provide compact fastening hardware for model maintenance, repairs and fresh assembly work. The steel build pairs a countersunk head with a hex socket drive, so each screw can sit flush in a matching recess while allowing firm, controlled tool engagement during installation. In the pack are 10 matching screws, shown with a dark metal finish and short threaded shafts suited to precise mounting points. The 3x6mm size makes this hardware relevant wherever that exact thread and length are specified in a compatible model or accessory assembly. A countersunk head is used where the screw needs to settle into the surface rather than stand proud, which helps preserve clean part alignment around plates, brackets or other fitted sections. The hex socket format also reduces the chance of slipping compared with a simple slotted head when careful tightening is needed on small-scale assemblies. These screws fit naturally into routine workshop tasks such as replacing worn fasteners, securing parts after servicing, or keeping spare hardware on hand for future adjustments. On RC cars and other model builds, timely replacement of damaged mounting hardware helps maintain consistent fit at the fastening point and supports reliable running after repeated use.  Warning! Not suitable for children under 14 years.

Screws & ball head screws

3x6mm Steel Hex Head Screws, model accessory

€2.89

These 3x6 mm steel hex head screws are replacement fastening hardware for model maintenance, repair and parts changes. The steel construction and internal hex drive support secure tightening with a matching tool, while the compact size suits smaller mounting points where consistent hardware dimensions matter. Supplied as a set of 10, they provide a practical stock of matching screws for workshop drawers, pit boxes or spare-parts cases. The rounded head shape and fully threaded shaft are suited to refitting components that rely on small, uniform fasteners. When an original screw is worn, lost or damaged, replacing it with the same 3x6 mm format helps preserve the intended fit at the fixing point. The dark metal finish keeps the set visually consistent, and the identical sizing across all 10 pieces simplifies sorting and selection during repair work. On a workbench, these screws suit routine servicing, rebuilds and hardware replacement on model assemblies that call for this exact size. They are also useful to keep on hand as spare fastening hardware, ready for quick swaps when a repair should not be delayed by a missing screw.  Warning! Not suitable for children under 14 years.

Screws & ball head screws

4 mm Adjuster M2, model accessory, 6-piece set

€3.19

This 4 mm Adjuster M2 pack provides 6 matching ball pans for model maintenance, repair work and fresh assemblies that call for the same connection part throughout a linkage setup. The compact shape and M2 specification make the set a practical choice when worn or missing joint pieces need to be replaced with matching components. Each ball pan is supplied as a separate small part, so the pack can support several connection points in one project or stay on hand as workshop spares for later servicing. The 4 mm dimension gives a direct reference when matching existing hardware, while the uniform off-white moulded finish helps keep the parts easy to identify among other small model components. Scope of delivery: 6 ball pans. This set suits bench repairs, routine parts replacement and planned builds where identical linkage fittings are required across the assembly. It also works well as a stock spare for model toolboxes and hobby drawers, ready for the moment a control connection or adjuster point needs the same M2 and 4 mm format again.  Warning! Not suitable for children under 14 years.

Screws & ball head screws

4 mm Serrated Wheel Nuts, model accessory, steel

€4.19

These 4 mm serrated wheel nuts are made for compatible 1:10 models and bring a clean, functional solution to wheel mounting and replacement work. The steel construction gives each nut the solid threaded form needed for repeated fitting, while the serrated base increases contact at the mounting point when tightened. In the workshop or at the track, that combination supports a firm connection between wheel and axle hardware. The set contains 8 wheel nuts, making it useful for complete wheel swaps as well as keeping matching spares ready for service intervals. The compact format suits routine maintenance jobs where lost or worn fasteners need to be replaced with the correct size. The metallic finish and flanged nut shape match the hardware style commonly used on model vehicle wheel hubs, and the threaded interior is designed for direct fastening rather than decorative use. As a dedicated accessory part, this set focuses on one specific task: securing wheel assemblies with the correct 4 mm steel nut. On a repair bench, the 8-piece count supports organized replacement across multiple corners of a chassis. During rebuilds or setup changes on compatible 1:10 models, the serrated contact face helps the nut seat with a more positive mechanical hold as the wheel is fitted and tightened.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

44mm TRF L.F. Drive Shafts, RC spare part

€22.49

These 44 mm TRF L.F. drive shafts are built for double cardan joint drivetrains that use swing shaft caps from Item 54921. The steel construction and fluorine surface coating focus on two key demands in RC driveline tuning: controlled movement at the joint and reduced friction where the shaft is working under load. Supplied as 2 matching shafts, the set supports a balanced left and right installation in compatible chassis layouts. A key update is the 10.8 mm needle pin section, which is 1 mm longer than on previous shafts. That extra length is specified to get more from swing shaft cap option parts, making these shafts a targeted upgrade for builders refining a double cardan setup rather than changing unrelated areas of the car. The LF44 marking shown on the shafts helps identify the part during maintenance or when several driveline options are kept in a pit box. In workshop use, these shafts suit rebuilds after wear, planned driveline updates, or a fresh parts selection for a compatible competition chassis. They are best matched with the stated cap system, where the longer pin section and low-friction coating can be used as intended in the assembled transmission layout.

Axes & drive shafts

45mm Drive Shafts, TRF421 spare part set

€18.99

These 45 mm drive shafts for TRF421 are a focused drivetrain spare for model car maintenance, supplied as 2 matching parts for Low Friction Double Cardan Joint Shafts. The dark metal shafts are marked LF45 and use a straight shaft form with joint ends shaped for the matching assembly. At the shaft end, each part uses a 10.8 mm needle pin. This detail is specified to work together with Item 54921 Reinforced Swing Shaft Caps, with 2 pieces each for front and rear fitment. The compatibility note is narrow by design: these shafts are only for cars that use Item 54921, which keeps the replacement choice tied to the correct drivetrain layout instead of a broad universal fit claim. As a spare part set, the pair supports maintenance after wear in the transmission area and restores the intended shaft length of 45 mm on both sides. The 2-piece format suits workshop stock, scheduled rebuilds and targeted repairs on a TRF421 setup. In a bench session, the matched pair helps keep the drivetrain specification consistent when replacing both corresponding shafts in the same assembly.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

46 mm TRF Swing Shafts, RC accessory, aluminium

€18.99

These TRF 46 mm aluminium half cardan shafts add a focused drivetrain upgrade for compatible RC chassis, combining low weight with a ball bearing mounted layout that helps the axle rotate with less friction. In running, that reduced drag supports steadier power delivery through direction changes, where speed loss at the shaft can affect how cleanly a car carries momentum. The set contains 2 lightweight 46 mm swing axles and is intended as a chassis-specific accessory rather than a universal fit part. The half cardan design suits drivetrain maintenance, replacement work and targeted tuning where the shaft assembly is a key wear point. For TRF421X use, the specification names compatibility with ball bearing set 51762 and differential joints 51764 when the shafts are installed on the TRF421 chassis 42384. That combination gives a clear reference for planning a matching drivetrain setup instead of mixing unspecified parts. On the bench, the defined 46 mm length helps identify the correct shaft format before installation. During track use, the ball bearing mounted construction supports smoother axle movement in repeated corner entries and exits, where friction control matters most in a responsive RC drivetrain.  Warning! Not suitable for children under 14 years.

Screws & ball head screws

4mm Ball Connector M2, model accessory, 5-piece

€3.99

This 5-piece set of 4 mm Ball Connector M2 hardware adds a compact connection point to model mechanisms that rely on precise moving links. Each connector uses a polished spherical head above a short neck, hex section and threaded post, creating a clear interface for compatible snap-on or pivoting parts in tight installation spaces. The 4 mm head size and M2 thread make these connectors suited to small-scale mechanical layouts where clean movement and accurate mounting matter. The metal construction gives each piece a defined shape for repeated fastening and removal during setup, adjustment or replacement work. The hex base supports tool-assisted tightening, while the threaded post seats into matching mounting points for a secure mechanical hold. With 5 identical connectors in the pack, the set can equip several linkage positions in one assembly or replace worn hardware across existing running gear. On the workbench, these connectors fit naturally into repair, tuning and fresh build tasks where steering links, control rods or other articulated parts need a ball-end mounting point. The consistent dimensions across all 5 pieces help keep left and right connection points matched when a model uses mirrored hardware.  Warning! Not suitable for children under 14 years.

Screws & ball head screws

4mm Flange Lock Nut Bla (8), RC accessory set

€3.89

This RC hardware set brings a clean wheel finish and a more secure fastening point to compatible model cars. Each 4 mm flange lock nut uses a nylon insert that grips the thread as the nut is tightened, helping the connection stay in place when the chassis is exposed to repeated vibration, direction changes and regular wheel removal. The set contains 8 blue flange lock nuts, shown as individual metal fasteners with a flanged base and visible locking ring. That flange gives the nut a broader contact surface than a plain hex nut, which helps distribute clamping force at the mounting point. The blue colour variation also changes the look of the wheel area, making it useful for refresh work on existing builds or for replacing standard hardware supplied in many RC kits. The parts are intended as accessory or spare hardware rather than a complete vehicle component group. Compatibility covers a range of touring car and off-road cars, making the set useful for workshop drawers, rebuild projects and routine running maintenance. When wheel hardware has been removed repeatedly or no longer matches the rest of the chassis, this 8-piece set provides a straightforward replacement option with a locking function built into each nut.

Screws & ball head screws

4mm Flange Lock Nut Blue, RC accessory, 5-pack

€13.79

These 4 mm flanged lock nuts bring a functional hardware upgrade to compatible RC vehicle setups, combining blue anodized aluminum with a compact fastening format that trims weight and sharpens the look of exposed wheel hardware. The metallic finish stands out clearly against darker rims, suspension parts and chassis details, giving maintenance work and final setup a more technical appearance. Each nut uses a hexagonal body with a threaded center hole and a wide integrated flange. That flange increases the contact area at the mounting point, which helps distribute pressure more evenly across the wheel surface than a narrow nut alone. The lock-nut format is suited to repeated fitting and removal during tuning, cleaning and routine parts changes. With 5 matching pieces in the pack, one extra nut remains available after a standard 4-wheel installation, which is useful to keep with trackside spares or workshop hardware. The small size and clear 4 mm specification make this set easy to match with compatible wheel axles and hubs in RC maintenance or customisation work. Whether replacing worn hardware, refining the finish of a competition-inspired build or keeping a spare ready between running sessions, these aluminum nuts add a precise mechanical detail where it is seen most.

Screws & ball head screws

4mm Shift Ball Connector M3, model spare part

€4.29

This 4 mm Shift Ball Connector with M3 thread is a dedicated spare part for Truck and HiLift model applications. The stated size and thread specification provide a direct reference for replacing the same connector type in an existing assembly, where the correct fit of small linkage hardware matters to the overall mechanism. Its role is focused and practical: restoring a worn, missing, or damaged connection point with the specified 4 mm ball format and M3 threading. Because the product data identifies Truck and HiLift compatibility, the connector is suited to those model ranges rather than to general, undefined use. That makes it a useful workshop part for routine maintenance, repair work, and keeping compatible builds equipped with the correct hardware standard. The compact format also stores easily alongside other model service parts, so the required connector type is ready when a rebuild or replacement is due. In a repair session, this spare part can be selected by its exact connector size and thread rather than by guesswork. For ongoing model upkeep, it supports a tidy stock of application-specific hardware for Truck and HiLift assemblies.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

4mm Shim Set, RC accessory, 0.1/0.2/0.3 mm

€11.29

This 4 mm shim set brings fine mechanical adjustment to RC maintenance and model workshop tasks where shaft spacing needs a precise correction. The pack contains 30 shims in total, divided into 10 pieces each at 0.1 mm, 0.2 mm and 0.3 mm, so clearance can be tuned in small measured steps instead of forcing a single thickness into every job. Each shim fits 4 mm shafts and is intended for situations where more clearance is required. The thin ring format slips onto the shaft to change spacing directly at the point of assembly, which helps when rotating parts need a more exact position. Combining different thicknesses from the set also allows intermediate spacing values, giving more control during drivetrain setup, axle work or other moving assemblies that rely on accurate alignment. On the bench, the 3 thickness options support methodical trial fitting during maintenance, rebuilds or parts replacement. The grouped sizes make it straightforward to compare spacing changes, correct excess play and refine the fit of compatible components without replacing the shaft itself.

Screws & ball head screws

4x10mm Step Screw, spare screw set for M-Chassis

€4.39

This spare screw set provides 5 matching 4x10 mm step screws for compatible model chassis work, with a compact format that suits replacement, maintenance and rebuild tasks. The stepped design combines a threaded section, a cylindrical shoulder and a domed head, so one fastener can secure a part while also maintaining the spacing that a plain screw may not provide. The data names TA02, TA03 and M-Chassis compatibility, giving a direct reference for parts matching during service work. In a workshop tray or spares box, the 4x10 mm size is easy to identify when a build calls for the same specification. The 5-piece quantity supports targeted replacement rather than forcing a full hardware change across a chassis. The metal construction fits the role of a small mechanical fastening part where repeated fitting and removal are part of normal model upkeep. This screw pack suits bench repairs, scheduled maintenance and the final stages of a rebuild when the correct shoulder screw is needed to complete a mounting point. It also works as a useful reserve for keeping compatible TA02, TA03 or M-Chassis models ready for the next running session.

Screws & ball head screws

5mm Adjuster Short, RC spare part set, 8 pieces

€2.89

This spare part set brings 8 short 5 mm adjusters into the suspension area of an R/C car, where low-friction material helps linked joints move with a smoother action. Each piece is shaped for use at connection points that need a pivoting link, making it a practical choice for maintenance, worn-part replacement or a fresh chassis build that calls for matching hardware. The short format suits tighter installation points than a longer adjuster and keeps the linkage layout compact around the joint. In use, the circular eyelet opening forms the attachment point for the connected rod or pin, while the low-friction composition focuses on reducing drag at the moving interface. That can help suspension parts articulate more freely as the chassis loads and unloads through direction changes, uneven surfaces and repeated laps. The set contains 8 identical adjusters, which supports consistent fit across several matching positions on a compatible R/C car. On a workbench, these adjusters fit naturally into routine rebuilds, suspension refreshes and setup corrections where several joints need the same part at once. During running sessions, smoother linkage movement can support cleaner suspension response as the car transitions through braking, turn-in and acceleration.

Screws & ball head screws

5mm Adjuster, model accessory, 19mm length

€3.49

This model accessory set supplies 6 ball pans sized at 5 mm diameter and 19 mm length for compatible maintenance and replacement work. The specified dimensions make the set easy to match against an existing assembly, especially when a worn or missing fitting needs the same connection size and overall length. The pack is intended for use with 50592, which gives a direct compatibility reference instead of leaving the fit to estimation. Ball pans sit at the connection point of linked parts, so the stated 5 mm diameter matters when selecting the correct hardware for a rebuild or service task. The quantity of 6 supports repeated replacement work across the same assembly and leaves matching spares available for later upkeep. On the workbench, this set fits neatly into routine model maintenance, whether a compatible build is being refreshed after use or a stored chassis is being brought back into running condition. The compact hardware format also makes it practical to keep alongside other small fittings for planned repairs and parts organisation.  Warning! Not suitable for children under 14 years.

Screws & ball head screws

5mm Ball Connector Nut, model accessory, 4pcs

€5.49

The 5mm Ball Connector Nut set supplies 4 matching threaded fittings for model assembly, repair and maintenance work. Each piece combines an internal screw thread with a hexagonal base, giving small mechanical connections a defined contact point for tightening and adjustment during a build. The compact black metal parts are shaped for clean integration into technical assemblies where consistent hardware matters. Their uniform form keeps all 4 fittings visually and mechanically aligned across the same application, which helps when replacing worn connector nuts or preparing matching hardware for a fresh setup. The 5 mm sizing gives a clear reference for compatibility within the intended assembly, while the threaded interior supports a direct fit onto the corresponding shaft or screw. On the workbench, these fittings suit routine servicing, parts replacement and detail-focused model projects that call for precise small hardware rather than mixed spare nuts. The 4-piece pack also leaves matching components ready for follow-up maintenance when the same connection point appears more than once in an assembly.  Warning! Not suitable for children under 14 years.

Screws & ball head screws

5mm Ball Head M3, model accessory, 10-piece set

€6.79

This 10-piece set of 5 mm Ball Head M3 parts adds a precise connection component to model maintenance, repair and assembly work. Each ball head uses an M3 threaded shaft and a 5 mm ball, a combination that suits compatible linkage and mounting points where a compact pivoting connection is needed. The metal construction and hex shoulder shown on each part support secure tightening during installation. The pack includes 10 matching ball heads, which helps keep spare hardware on hand for repeated service jobs or fresh builds that call for the same fitting throughout. The spherical head shape is suited to moving connection points that need controlled articulation rather than a fixed joint. The short threaded section keeps the mounting format specific and easy to match against existing compatible parts. The gold-coloured finish shown in the set also makes each piece easy to identify in a parts tray or workshop drawer. On a repair bench, these fittings suit the replacement of worn connection points on compatible models. During a new build, the matching 10-piece quantity supports consistent hardware selection across multiple mounting positions and leaves reserve parts available for later maintenance.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

5mm Body O-Rings, model accessory, 10 pieces

€3.09

These 5 mm body O-rings are small model accessory parts that make a visible difference at the body mounts. Fitted to body mount rods, they allow fine height adjustment of the bodyshell position, so the shell can sit with a more controlled fit on the chassis during setup. The set contains 10 O-rings for replacement stock or fresh installation on compatible body posts. Their role is not limited to spacing: each ring also provides a cushioning effect between the bodyshell and the mount point. On rougher driving surfaces, that added cushion helps reduce body chatter that can appear when the shell moves against the posts over bumps. This gives the shell mount a tidier, more settled feel while the model is running. In workshop use, the rings are easy to keep on hand for routine maintenance, rebuilds, or shell changes between different bodyshell setups. They suit drivers who fine-tune shell height on body mount rods and want spare mounting hardware ready for regular track or car park sessions.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

5mm Shim Set, RC accessory, 0.1 0.2 0.3mm

€11.29

This 5 mm shim set brings precise spacing control to RC chassis work, with 3 thicknesses at 0.1 mm, 0.2 mm and 0.3 mm for fine mechanical adjustment. Used at 5 mm fitment points, the shims help take up excess movement where a cleaner, tighter setup is needed around suspension parts or wheel axles. The set includes 30 shims in total, arranged as 10 pieces of each thickness, which supports repeated setup changes without relying on a single size. Small spacing differences can change how parts sit against each other, and these thin rings make those corrections measurable rather than improvised. On a maintenance bench, they can be selected to match the amount of free play present at a given point. On a fresh build, they support more exact placement of moving parts before the chassis goes into use. The shim assortment suits both on-road and off-road Tamiya vehicles, so the same pack can serve different running platforms in one workshop. Whether the goal is tidying axle movement, refining suspension fit or keeping a race chassis more closely adjusted, the 5 mm format gives a compact tuning part that earns its place in a spares box.

Screws & ball head screws

5mm/M3 Ball Socket Set, model accessory, 8 pieces

€5.99

This 5 mm/M3 ball socket set brings a straightforward replacement option for compatible model linkages, with 8 matching parts ready for maintenance, repair work or a fresh build. The rod-end style shape and circular socket opening suit connection points that rely on a compact joint with controlled movement. Each piece is formed as a small connector end with a faceted outer body, a cylindrical shaft and a socket head that pairs with the stated 5 mm/M3 specification. That combination helps when an existing setup needs the same dimension rather than a close substitute. The pack format keeps several identical parts on hand at once, which is useful when multiple joints on one chassis use the same fitting or when spare hardware belongs in a regular bench stock. The black finish keeps the set visually consistent with many technical assemblies without drawing attention away from the surrounding components. In workshop use, the set fits naturally into routine servicing after wear at steering or suspension connection points. It also suits rebuilds where matching linkage ends across several rods help keep the assembly consistent and easy to sort during installation.  Warning! Not suitable for children under 14 years.

Screws & ball head screws

5x9mm Ball Connector, model accessory, 5 pcs.

€7.89

These 5x9 mm ball connectors add a compact mechanical link point to RC and model assemblies where a threaded joint and a smooth pivot surface need to work together. Each piece combines a 5 mm ball, an M3 threaded shaft and a 9 mm length, creating a clear fit for linkage tasks that depend on accurate spacing and dependable attachment. The polished metal finish and defined ball shape suit moving connections such as steering rods, suspension joints or other articulated model hardware, while the hexagonal shoulder provides a practical grip area during fitting. With 5 matching connectors in the pack, the set supports fresh builds, maintenance work and the replacement of worn fastening points. The small format also makes these parts useful for keeping workshop drawers or field boxes stocked with commonly needed RC hardware. In a chassis rebuild, the connectors can be fitted where rods or jointed parts need a threaded anchor and a pivoting contact point. On the bench, the uniform dimensions help keep left and right linkage positions consistent when several matching connection points are required in the same assembly.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

6 mm Shim Set, model accessory, 0.1 0.2 0.3 mm

€16.29

This 6 mm shim set brings precise spacing control to model assemblies that need a cleaner fit on 6 mm shafts. With 3 thicknesses at 0.1 mm, 0.2 mm and 0.3 mm, the set supports small corrections where mechanical play affects alignment, rotation or part position. The set contains 30 pieces in total, arranged as 10 shims of each thickness. That spread makes it possible to compare different spacer combinations during a build or while servicing an existing model, instead of working around a single dimension. The thin shim format suits jobs where only a fraction of a millimetre is needed to correct end float or reduce unwanted movement between parts. Used singly or in combination, the spacers help adapt the fit to the exact requirement of the assembly point. On the bench, the set suits gearbox work, axle spacing and other 6 mm shaft applications where measured adjustment matters. As a compact workshop supply for model maintenance, repair or fresh assembly, it adds a practical range of fine spacer sizes that can be kept ready for repeated mechanical setup tasks.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

A-Parts Axlehousing CC-01, spare parts set

€22.79

A-Parts Axlehousing CC-01 is a spare parts set for the CC-01 platform and is listed as parts for 58132. The black injection-molded runner carries several unused structural components in one frame, including axle housing style sections and mounting pieces that support a clean replacement job when original parts need to be swapped. The molded layout keeps each piece attached until removal, which helps with identification before assembly and reduces mix-ups between similar shapes. The visible parts include long housing sections, bracketed elements and a larger case-like component, all formed with mounting holes and connection points that suit chassis or drivetrain installation. Because the pieces come as a matched set on one sprue, builders can replace damaged sections with components produced together rather than mixing unrelated leftovers from a parts box. This kind of spare set fits naturally into bench maintenance, rebuild work and parts sorting between running sessions. When a CC-01 chassis needs fresh housing components after wear or breakage, the set provides the specific molded forms needed to return the assembly to working order.

Other spare parts & accessories

A-Parts Gearbox F/R 58370, RC spare parts

€14.29

This A-Parts sprue is made for the 58370 and provides black injection-molded components for the gearbox F/R area of the DF-03. The unassembled runner groups housing halves, covers and structural sections in one set, giving repair work a direct route back to the intended drivetrain layout. The molded pieces show reinforced ribs, screw holes and cylindrical shaft or bearing mounts that matter when a transmission case needs its original geometry. A larger frame-like section with elongated slots adds another chassis-facing support element, while rounded shell parts serve as protective case sections around moving drivetrain parts. Because the components are supplied on the sprue, each shape stays clearly separated until preparation begins, which helps with part checking before installation. The glossy black finish matches the technical look of many RC chassis internals. This spare parts set suits maintenance benches, rebuild projects and targeted gearbox repairs where damaged housings, brackets or covers need replacement with matching forms. It also supports keeping a DF-03 running with dedicated structural parts on hand for future service work.

Other spare parts & accessories

Alligator Clip for P. Stand, model tool set

€5.99

These alligator clips add a simple, controlled way to hold small model parts while cement or paint dries. The spring-loaded hinge and serrated jaws grip components firmly, so freshly finished pieces can stay separated from the work surface and remain easier to handle during careful bench work. Each pack contains 4 matching clips, which supports parallel work on several parts in the same session. The oval wire loop at the end of each clip provides a clear connection point for mounting on a compatible stand. The clips are intended for use with the Painting Stand, Work Stand and Bottled Paint Stand named in the product data, making them a practical addition for painting, gluing and drying steps where direct hand contact can disturb a finish. On a model bench, the clips can hold newly cemented sections while joints set, or keep painted components raised and separated between coats. Their compact metal form suits detail-focused tasks where small parts need a temporary grip point and a cleaner path through finishing work.

Shock absorbers & springs

Alum. Damper Retainer -1mm, RC part, blue anod

€27.99

The Alum. Damper Retainer -1mm is a suspension tuning part for compatible RC chassis, combining machined aluminum construction with a blue anodized finish and a precise fit around the damper spring area. By lowering the spring set position by 1 mm compared with the aluminum mount of the OP595TRF shock, it supports a lower vehicle height and a more exact starting point for chassis setup. This set contains 4 spring plates for matched installation across the suspension. The rigid aluminum holder is made for reliable initial adjustment of the damper spring, helping setup changes translate more directly at the shock. Compatibility extends beyond the main chassis list: on TD4 and TD2 chassis, only standard front dampers can be installed. On MF-01X chassis, use with 42102 or 42273 or 42354 or 42355 or 54000. On F104 and F104W chassis, use with 53901. In workshop use, the 1 mm change gives a concrete option when refining stance and spring preload on touring, formula, or off-road based builds that share these chassis families. The 4-piece set suits rebuilds, replacement work, or a fresh suspension setup where consistent hardware across the dampers matters.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

Alum. Turnbuckle Wrench blue, model tool, 3.0 mm

€14.99

The Alum. Turnbuckle Wrench blue is a dedicated model tool for fine setup work on vehicles with 3 mm adjustable tie rods or camber rods. Its 3.0 mm clamping axle format is made to engage the turnbuckle directly, so alignment changes can be made with a controlled hand movement at the workbench between runs or during a full chassis service. The blue aluminum handle combines low weight with a firm feel, and the ribbed cylindrical shape supports stable finger placement while small adjustments are made. A forked open-end tip slides around the rod section to apply leverage where a standard wrench would be too bulky. This focused shape suits RC maintenance jobs where steering links and camber rods sit close to surrounding parts. The scope of delivery contains 1 clamping axle wrench. On a tuning bench, in a pit box, or beside a partly stripped chassis, this tool supports repeatable suspension and steering setup work without taking extra space. It also works well as a dedicated addition to a model building tool roll where 3 mm linkage hardware is adjusted regularly.  Warning! Not suitable for children under 14 years.

Shock absorbers & springs

Aluminium Shock Absorbers, 55.62 mm, 2-Piece Set

€51.99

These aluminium shock absorbers bring a low-friction damper setup to compatible Tamiya M chassis models, combining a machined cylinder interior with a 55.62 mm overall assembled length. The metal damper design is intended for smooth operation, giving the suspension a more even response as the shafts move through the cylinder. Compatibility covers the M-06 chassis, M-06 PRO chassis, M-05 ver.II PRO chassis, M-05 chassis and M-05 PRO chassis. The set contains 2 shock absorbers and is supplied with 48 pieces for assembly, including the hardware and sealing parts needed for the damper build. Aluminium bodies, coil springs, shafts, rod ends, clips and rings form a detailed suspension set that suits replacement, rebuilding or chassis tuning work on the listed platforms. Mounted on a compatible M chassis, the dampers support controlled suspension movement during cornering, braking and direction changes. The purple finish gives the underbody a distinctive technical look, while the complete 2-piece configuration fits neatly into workshop sessions focused on maintenance, setup changes or restoring smooth damper action.  Warning! Not suitable for children under 14 years.

Spare parts for old cars

Aluminum 4mm Lock Nut Set, model accessory, pink

€7.19

This set of 4 aluminum lock nuts brings a precise fastening detail to model builds and maintenance work, while the pink anodized finish adds a bright visual accent at the wheel area. With a 4 mm size, the nuts suit compatible threaded axles where compact hardware needs to stay easy to handle during setup and part changes. The lock nut design is made for fastening tasks where vibration and repeated removal matter, making the set useful for routine servicing as well as colour-coordinated upgrades. Aluminum gives each nut a light metal construction that fits neatly into performance-focused builds without adding bulky hardware. The pink finish is more than a colour note on the parts tray: it helps distinguish this set quickly from standard silver or black fittings during bench work. Supplied as 4 matching pieces, the set covers one complete wheel mounting point on many model layouts. On the workbench, these nuts fit naturally into rebuilds, wheel swaps and detail updates where small hardware shapes the final look as much as the mechanical fit. They also suit spare-parts storage for regular running sessions, keeping a matching set ready when worn or misplaced fasteners need replacement.

Other spare parts & accessories

Antenna for 56019, model accessory, 175 mm

€4.49

This antenna for 56019 is a dedicated model accessory with a stated length of 175 mm, intended for use where the matching reference calls for this exact part. The slim rod format gives the model a clean, defined finishing detail while keeping the replacement focused on the named application rather than a generic spare. The part is supplied as 1 piece and is described simply as an antenna for 56019, which keeps selection clear when a specific replacement is needed. The visible form shows a long metal rod with shaped ends, including a hooked bend at one end and a coiled section at the other, indicating a functional mounting or connection point within the matching model setup. That concrete shape matters when replacing a missing or bent antenna, because the end form can be just as important as the overall length. Used on the correct model, this 175 mm antenna suits repair work, parts replacement, or the completion of an existing build that needs the specified external component. It fits naturally into workshop tasks such as restoring a stored model, replacing a worn original, or finishing a project with the named 56019 reference in mind.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

Antenna Pipe 300mm, model accessory, black

€0.79

This black antenna pipe adds a neat, functional finishing detail to compatible RC model setups. With a length of 300 mm or 30 cm, the tube gives the antenna a defined route and helps maintain a clean layout above the body where a loose wire would look untidy. The straight tube form makes it useful as a replacement part in routine maintenance, after repairs, or when refreshing an older build with worn running hardware. Its single-purpose design keeps the fit straightforward: the pipe sits in the model's antenna mount and supports the aerial in an upright position. The black finish keeps the look understated, which suits a wide range of body colours and chassis layouts without drawing attention away from the model itself. In workshop use, a spare antenna pipe is a practical part to keep alongside other RC maintenance essentials, especially for builds that still use a visible aerial tube. It also suits restorations where small external details help return a model to a complete, ready-to-run appearance.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

Antenna Pipe 380mm, model accessory, clear

€0.89

This clear antenna pipe is a straightforward model accessory for RC setups that use an external aerial guide. With a length of 380 mm, it provides a long tube that can be fitted and trimmed to match the required antenna height on the model, keeping the wire routed in a visible, upright position above the bodyshell. The transparent finish leaves paintwork, markings and body lines unobstructed, which helps preserve the look of the completed model while still making the antenna route easy to follow during fitting. Supplied as 1 piece, it works well as a direct replacement for a damaged tube or as a spare kept on hand for workshop use. The simple tube format also makes it useful across routine maintenance tasks where a clean, correctly sized aerial guide is needed. On the bench, the 380 mm length gives enough material for model-specific adjustment before final installation. During transport, storage and running sessions, the fitted tube helps keep the antenna wire guided consistently instead of leaving it loose around the shell area.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

Anti-Wear Grease 3g, model lubricant tube

€12.991 kg = €4,330.00

Anti-Wear Grease in a 3 g tube supports smooth maintenance work on model drivetrains by combining high viscosity with precise placement. On differential gears, shafts and drive axles, the grease adheres well to rotating parts, so lubrication stays where the mechanism needs it during repeated movement. The formulation is described for model vehicles and is supplied in a compact tube with a fine, narrow nozzle for controlled dosing on small contact points. That narrow outlet helps place a small amount directly onto gear teeth, axle sections or shaft ends instead of coating surrounding areas. The grease is temperature stable and retains its viscosity over a wide temperature range, which helps keep application characteristics consistent as moving parts warm up in use. The supplied quantity is 3 g, making it suited to targeted servicing rather than bulk workshop filling. In regular upkeep, the tube fits neatly into a field box or bench drawer and is ready for quick drivetrain attention between runs. It suits focused lubrication tasks on compact assemblies where accurate placement matters, especially around differentials and other enclosed rotating components.  Warning! Not suitable for children under 14 years.

Shock absorbers & springs

Axle Spring (2) 58416, model spare part

€0.89

Axle Spring (2) 58416 is a model spare part for the axle area, supplied as a 2-piece spring set under the stated 58416 designation. The format suits maintenance tasks where a matching replacement is needed for a worn, missing or no longer usable spring in a compatible model assembly. The focus here is clear part identification rather than broad fit claims. The ShortDescription names the component as an axle spring, and the pack count confirms 2 springs in the set. That makes the set useful for organised parts storage, planned servicing and direct replacement work where the correct designation matters. In a workshop drawer or spares case, the numbered reference helps separate this spring set from gears, shafts, screws and other maintenance components. During repair or upkeep, a dedicated replacement spring set can help return the axle section to its intended mechanical role in the assembly. The compact 2-piece format also suits keeping a matched pair on hand for future service jobs on compatible model builds.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

Axle Spring (2), spare part for model chassis

€2.99

This set of 2 axle springs is a dedicated spare part for 58347 and is shaped for mechanical return action at the axle assembly. Each spring is formed from silver-coloured metal wire and uses a tightly wound coil with one short straight leg, one longer angled arm and a small loop at the end, making the part easy to identify during maintenance. The geometry shown in the part itself matters: the coiled section stores torsion, while the two arms transfer that force back into the moving mechanism. That makes these springs suitable for restoring rotational resistance, return tension or repositioning in the intended axle location on a compatible model. Supplied as a matching pair, the set supports like-for-like replacement where both sides of an assembly use the same spring form. For workshop use, the clear standalone shape helps with part checking before fitting and with replacing worn, bent or missing hardware in an existing chassis setup. As a model spare part rather than a general hardware spring, it is best used where the 58347 fitment and the pictured form match the original assembly requirement.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

B-Parts Gearbox Super Clod Buster spare parts

€19.49

B-Parts Gearbox Super Clod Buster 58321 is a replacement sprue for model maintenance and repair, bringing key transmission-area components together in one clearly structured set. The black injection-moulded frame presents the parts in their original grouped layout, which helps with visual checking before each piece is removed and installed. The sprue shows 2 large matching housing halves, a rounded cover plate, 2 circular discs with evenly spaced holes, a larger curved cover piece, and several smaller link arms and connectors. One housing half features an integrated cylindrical section, indicating a dedicated enclosure area within the gearbox assembly. The opposite half carries reinforcing ribs and multiple screw points, giving the rebuilt section the same shaped mounting structure as the original part set. Small moulded part numbers are also visible on the frame, which supports part recognition during a careful rebuild. This spare-parts set suits workshop use when a Super Clod Buster gearbox section needs replacement after wear, damage or a detailed restoration. It also helps keep a rebuild consistent by supplying matching moulded pieces from the same B-Parts group rather than mixing unrelated components.

Spare parts for old cars

Ball Bearing Set Hornet Grasshopper Chassis

€17.19

This ball bearing set brings together 10 replacement bearings for a focused chassis service job across several classic Tamiya platforms. The pack contains 9 x 1150 ball bearings and 1 x 850 ball bearing, matching the sizes stated for the supported models and giving a clear route to replacing worn rotating parts with the correct mix. The set is intended for Hornet, Grasshopper, Grasshopper II, Super Storm Dragon, CW-01 chassis models such as Lunch Box, plus Mad Bull, Mad Fighter and Rising Fighter. Ball bearings sit at rotating points where shafts and axles need controlled movement, so the correct size matters as much as the quantity. The metal construction and ring design suit maintenance work on running gear and transmission areas where smooth rotation is needed. As a dedicated bearing pack rather than a mixed hardware assortment, it keeps the service task focused on the exact bearing types named in the data. It suits routine rebuilds, repairs after extended running, or planned upgrades on compatible chassis already on the bench. Kept in a workshop drawer or parts case, the 10-piece mix gives a ready reference for several well-known buggy and CW-01 based models when replacement bearings are due.

Other spare parts & accessories

Ball Differential Grease 10g, RC lubricant

€11.39

Ball Differential Grease 10g is a dedicated lubricant for ball type differential gearing in RC model vehicles, supplied in a compact tube with an applicator nozzle for controlled placement on small drivetrain parts. The 10 g fill gives a practical amount for routine servicing, whether the differential is being refreshed during a rebuild or maintained between running sessions. The grease is specified for differential use rather than general-purpose lubrication, which keeps the copy focused on the part it is made for. The supplied tube format helps direct the grease into tight mechanical areas where ball differential components need careful coverage. Compatibility notes in the data reference a wide range of chassis families when used with the stated related parts, including XV-01, XV-01T, XV-01 PRO, M-07 CONCEPT, M-08 CONCEPT, TA06, TA06 PRO, TA06 MS, TT-02, TT-02D, TT-01 TYPE-E, TT-01D TYPE-E, TT-02RR, TT-02FT, TT-02B, MF-01X, M-05, M-05 PRO, M-05 ver.II PRO, M-06, M-06 PRO, DT-02, DT-03 and DT-03T. On the bench, the narrow nozzle supports precise application during drivetrain maintenance, helping keep grease where the ball differential needs it instead of spreading it across surrounding parts. In workshop use, the small tube stores easily with other RC service supplies and is ready when a ball diff setup is due for fresh lubricant.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

Basic File Set Smooth Dbl. Cut(3), hobby file set

€8.29

The Basic File Set Smooth Dbl. Cut(3) brings 3 distinct file shapes into one compact bench set for shaping, smoothing and refining small model parts. Flat, round and semi-circular profiles make it easier to match the filing surface to the contour being worked, whether the task is cleaning an edge, opening a curve or evening out a narrow recess. Each file is 140 mm long, with a 2.5 mm handle diameter that suits close hand control on detailed work. The double-cut surface uses 38 cuts per cm, giving the files a fine, even bite that supports a smooth finish rather than heavy stock removal. This makes the set especially suited to surface preparation on plastic scale models, while still handling Mini 4WD parts and selected metal areas where careful finishing matters. At the workbench, the different profiles help move from straight runs to rounded sections without switching to oversized tools. Black rubber grips keep the hold consistent during short filing passes, and the included vinyl case stores the 3 files together between build sessions and transport.

Gears & motor pinions

BB-01 48 Pitch Spur Gear 86T, RC spare part

€4.59

The BB-01 48 Pitch Spur Gear 86T is a dedicated RC spare part for drivetrain setups that use a 48 pitch gear standard. Its circular toothed form and 86-tooth count define how it meshes with the matching pinion, making it a precise choice when a worn transmission part needs replacement or a specific gearing ratio is required for a build. This pack contains 1 spur gear. The part is intended for use with a 48 pitch pinion gear, so the tooth profile stays within the same pitch system across the gear mesh. That matters during maintenance and rebuild work, because matching pitch standards help the teeth engage correctly during rotation. The gear is shown as a molded component with a central mounting hole and reinforced face structure, details that support its role as a fitted mechanical part rather than a general workshop accessory. In practical use, the gear suits bench repairs, scheduled part changes and drivetrain refreshes on various R/C cars that accept this specification. When an RC chassis calls for an 86T spur gear in 48 pitch format, this part provides a direct, clearly defined replacement to keep the transmission setup on the intended gearing standard.

Axes & drive shafts

BB-01 D-Parts Suspension Arms, chassis spare set

€12.79

The BB-01 D-Parts suspension arm set supplies the core chassis pieces that guide wheel movement at both the front and rear of a BB-01 build. With 2 front arms and 2 rear arms in the pack, the set supports a matched replacement across both ends, keeping the suspension layout consistent when worn or damaged parts need changing. Each arm is molded in glass fiber-reinforced nylon, a material choice suited to detailed chassis parts with hinge-pin mounts and outer pivot points. The shared right and left component shape reduces sorting during maintenance, since the same form is used on both sides. The included D-Parts for the BB-01 chassis focus on the mechanical areas that control suspension travel and the connection points around the wheel assemblies. This set fits workshop use, routine upkeep, or a rebuild after hard off-road sessions with a BB-01 machine. It also works as a practical spare to keep alongside other chassis parts, ready for quick replacement when the front or rear arm assemblies need attention.

Shock absorbers & springs

BB-01 Damper Adjuster V Parts, RC spare set

€6.49

The BB-01 Damper Adjuster V Parts set brings front and rear damper adjuster components together on one black molded sprue for focused repair and maintenance work. Shaped rings, collars and linking pieces are arranged as separate numbered sections, so the required part can be identified before removal and fitted where the BB-01 chassis calls for it. The visible sprue layout supports clean handling at the bench, with each molded section kept in place until use rather than arriving as loose pieces. This format helps when comparing part shapes, checking orientation and separating only the needed component during a repair. The set belongs to the model supplies category and is intended for RC and model servicing rather than stand-alone play. Its compact collection of adjuster parts concentrates on one chassis area, which keeps replacement work specific instead of relying on mixed universal hardware. On a workshop table, the numbered sprue can be checked against the relevant build stage or service task before installation. For an existing BB-01 build, the set provides a direct source for renewing front or rear damper adjuster parts when the original pieces need replacement.

Axes & drive shafts

BB-01 Dogbone Shafts, RC spare part, steel

€18.99

These BB-01 Dogbone Shafts are a dedicated steel spare part for the BB-01 chassis and supply a matched pair for drivetrain service. The 2 shafts use the classic dogbone layout, with a pinned ball end on one side and a cup-style joint end on the other, so rotational force can pass between connected drivetrain parts while suspension movement changes the working angle. Crafted in carbon tool steel, the shafts focus on the part of the drivetrain that sees repeated motion under load. The black metal finish and the identical left and right pieces shown in the set make them suited to a like-for-like replacement when an existing pair needs renewal. As a chassis-specific component, the fitment stays tied to the BB-01 platform rather than a broad universal range, which helps keep maintenance accurate and parts selection straightforward. On a bench build, repair session or routine drivetrain refresh, this 2-piece set covers the shaft pair in one pack. It suits keeping a running chassis in service, replacing worn transmission links, or preparing spares for future maintenance on BB-01 based RC vehicles.

Axes & drive shafts

BB-01 Front Upright Set, RC spare parts, 2 pcs

€7.19

The BB-01 C-Parts front upright set supplies 2 replacement components for the front end of a BB-01 chassis, giving RC model maintenance a direct way to renew a key mounting area. Each upright is molded in glass fiber-reinforced nylon, a material choice that suits parts handling steering pivot loads, wheel support points and repeated workshop fitting. The set uses the same component shape for right and left, which simplifies parts identification when a front corner is being rebuilt. The large circular opening in each upright forms the bearing seat area, while the molded mounting points connect with the surrounding chassis hardware. As C-Parts for the BB-01 platform, these pieces belong to the chassis structure itself rather than to bodywork or trim, making them relevant for repair, upkeep and keeping an existing build in running condition. On a bench setup, the pair can replace worn, damaged or missing originals during a front-end refresh on a BB-01 model. The 2-piece format also suits keeping matching spares on hand for routine service, especially when steering and wheel support components need to be exchanged as a pair.

Other spare parts & accessories

BB-01 Main Chassis, RC spare part for BBX

€21.29

The BB-01 Main Chassis is the core frame section for BBX 58719 and provides the shaped base around which the vehicle layout is built. Its black molded form combines an elongated tub design with a large central compartment, creating dedicated space for the main internal installation while keeping the underside profile structured by integrated ribbing. Across the frame, molded screw posts and cylindrical mounting areas define where matching assemblies attach, while rectangular side slots add further connection points along the chassis walls. The one-piece construction keeps the geometry consistent across the length of the frame, which matters when replacing a worn or damaged base on an existing BB-01 build. The underside view shows a symmetrical layout with reinforcement lines running through the tub, giving this spare part the form needed to carry the rest of the chassis hardware in its intended position. This replacement part suits repair work, rebuilds and parts-based restoration of a BBX 58719 using the BB-01 platform. It fits naturally into workshop sessions focused on bringing an RC vehicle back into running condition or preparing a fresh chassis foundation for the next stage of assembly.

Axes & drive shafts

BB-01 T Parts, rear suspension mount set

€14.29

The BB-01 T Parts rear suspension mount set is a focused replacement and maintenance set for the specified suspension area, giving builders the exact molded shapes needed for work on the rear mounting section. The sprue format keeps the components together in one organized frame until removal, which helps with part identification before fitting begins. The visible layout includes multiple molded pieces in black and dark gray, with each shape formed for a technical role within the assembly rather than as a generic mixed parts pack. Numbered positions on the runner support orientation during workshop handling, and the molded frame format helps keep smaller connectors and bracket-style pieces grouped before installation. This makes the set useful when a damaged mount section needs renewal or when a build calls for the named BB-01 rear suspension area to be rebuilt with matching parts. On the bench, the set suits careful repair sessions, planned maintenance, or keeping key replacement parts ready alongside an existing BB-01 build. It also works well as workshop stock for model owners who prefer to keep the specified suspension mount section serviceable with the correct dedicated parts.

Gears & motor pinions

Bevel Gear Differential Set, RC spare part kit

€5.99

This bevel gear differential set is a drivetrain spare part kit for selected RC chassis, built around the internal mechanism that distributes drive through a differential assembly. Supplied as a kit version, it provides 8 pieces for differential service on compatible platforms and suits repair work that focuses on the gear internals rather than the complete chassis. The set is specified for CR-01 and DT-02 chassis, making it a targeted choice when those platforms need matching replacement parts in the differential area. The included contents are 1 bevel gear differential set with 8 pieces. Studio imagery shows the internal layout clearly, with larger bevel gears, smaller mating gears, a 3-armed carrier and 2 flat washers or shims, all centered on the gear action inside the assembly. That component mix supports rebuilds where worn or damaged internal differential parts affect drivetrain function. In workshop use, this kind of set suits routine maintenance, repair after heavy running, or a planned refresh of the axle internals on a compatible chassis. It is not available for XB models, so the fit remains tied to the listed chassis platforms and their matching differential setup.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

Bevel Pinion Gear, spare part for model drivetrain

€3.59

This bevel pinion gear is a dedicated spare part for model drivetrain service, built to pass rotational force through an angled gear interface inside a transmission assembly. The compact metal component combines a toothed upper edge with a conical body, making it suitable for mechanical layouts where direction changes within the drive line are required. Reinforced rib-like shaping along the gear body adds structural definition to the part itself, while the central mounting opening is formed for installation on a shaft or axle. That layout supports correct positioning within the surrounding mechanism and helps restore clean meshing when an original gear shows wear or damage. Supplied as 1 individual gear, it suits selective replacement work where only the affected transmission element needs to be exchanged. The plain silver-gray finish keeps the mechanical form easy to identify during maintenance and parts sorting. In workshop use, this spare gear fits repair jobs on model assemblies that rely on compact internal power transfer between connected drivetrain parts. It also serves as a practical replacement to keep an existing build in running condition after wear in a heavily used transmission section.  Warning! Not suitable for children under 14 years.

Gears & motor pinions

Bevelgear Set, model spare parts for drivetrain

€5.19

This bevelgear set brings the key transmission parts needed for focused drivetrain maintenance on compatible model assemblies. The set contains 5 metal gears: 2 larger bevel gears with central bore openings and 3 smaller pinion-style bevel gears with short shafts. Their angled teeth are made to mesh at intersecting shaft positions, a layout commonly used to redirect rotary motion through a compact gearbox section. The combination of larger hub gears and smaller pinions supports replacement work where worn or damaged gear teeth can affect smooth running. Because bevel gears transfer motion across a change in shaft direction, they are suited to mechanical areas where drive needs to turn through an angle rather than continue in a straight line. The silver-gray metal construction gives each gear a clearly defined tooth profile and a technical finish that matches the functional role of these parts. Compatibility is stated for BB18, BB19 and BB20, with reference to 58618 Mt.Bee. On the workbench, this set suits planned servicing, targeted repair, or keeping essential transmission parts ready for a compatible model. The clearly differentiated gear sizes also help when matching the correct meshing pair during maintenance and reassembly.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

Body Mount Extension Set 5.5 mm, RC car accessory

€7.99

The Body Mount Extension Set 5.5 mm adds a precise height correction to RC car body posts when a different bodyshell calls for more clearance. Each extension piece is designed to work with 5.5 mm to 6 mm diameter body mounts, and the included snap pins lock the selected position through the adjustment holes for a firm mechanical hold. Inside the set are 4 body mount extensions, plus 4 snap pins in 6 mm and 7 mm sizes. The parts are intended for touring car chassis and M-Chassis cars, where body posts may already have been cut down for another shell. Instead of replacing the full mount, this set extends the existing post by 5.5 mm and keeps the mounting point usable for another body setup. The fitting method shown in the leaflet uses the extension on the chassis-side body mount and secures it with a snap pin through the cross hole. This accessory suits workshop adjustments, shell swaps and rebuilds where body height needs a small, exact correction rather than a full change of mounts. It is compatible with TT-01, TT-02, TA05, TA06, TB-03, TB-04, XV-01, FF-03, M-05 and M-06 chassis body mounts, making it a practical addition for keeping several RC car bodyshells in rotation.

Other spare parts & accessories

Body Mount Plate BH 7/8, model accessory set

€11.49

The Body Mount Plate BH 7/8 is a model accessory set for the 58441 and 58452 references named in the data. With 2 mounting plates included, it supplies the specific hardware needed for work on the body mount area, whether the goal is replacing an existing part or completing a matching assembly step on the intended build. Each plate is shown as a formed metal component with a rectangular profile, rounded corners, 2 screw holes and a shaped center section. Those details matter during installation, because the hole positions and stamped form help the plate sit in the intended location and connect with the surrounding structure as designed. The BH 7/8 designation keeps the part identification aligned with the named application, which is useful when sorting spares for maintenance or rebuild work. The compact hardware format also makes this set a focused choice when only the mounting section needs attention rather than a wider parts replacement. On a workshop table, the 2 plates can be set alongside the target chassis parts and matched directly to the specified 58441 or 58452 build. For routine upkeep, rebuilds or parts sorting, this set keeps the replacement task centered on the exact mounting hardware named in the data.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

Body Mount Set, RC spare parts for DT-03 chassis

€9.99

This E-parts body mount set is made for selected RC chassis and supplies the core parts needed when body fixing points need replacement. It fits DT-03, DT-03T, G6-01, G6-01TR, TL-01, FF-02 and WR-02 applications named in the data, combining molded mounts with matching hardware for a direct service task at the shell mounting area. The black components are shaped for chassis attachment and body support, while the included mounting material covers the fastening work tied to this set. Multiple hole positions on the molded parts allow the mounting point to be set according to the chassis layout and shell position, which matters when replacing worn posts or correcting body fit after use. As E-parts, these components suit maintenance benches, rebuilds and parts boxes where chassis-specific replacements need to stay close at hand. The set works well during routine RC upkeep, after a cracked mount, or when a stored chassis is being returned to running condition with the correct fixing parts. In workshop use, the combination of mounts and screws keeps the repair centered on one compatible set instead of mixing unmatched hardware from different spares.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

BT-01 C Parts, wheel axle spare parts set

€6.99

The BT-01 C Parts set supplies original replacement components for the BT-01 chassis, centering on wheel axle and centre shaft parts used in the drivetrain. Differential cup joints, axle shafts, dogbone shafts and propeller shaft joints are grouped on one sprue, giving a direct source for matching parts when a running chassis needs repair or a rebuild calls for fresh hardware. These components handle connection and rotation transfer inside the BT-01 layout. Dogbone shafts link moving drivetrain sections, while cup joints and shaft ends sit at key handoff points between connected assemblies. Using original parts helps maintain the intended fit of the chassis design and keeps replacement work aligned with the existing BT-01 structure. The set is described as C Parts wheel axles and centre shaft, which makes its role within the chassis system clear for maintenance planning. This spare parts set fits workshop use, routine upkeep and targeted replacement after wear or damage in regular RC running. It also supports keeping a BT-01 chassis ready for the next rebuild session by covering several related drivetrain components in one pack. Compatible with the BT-01 chassis.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

BT-01 T Parts, RC spare parts, suspension arms

€6.79

The BT-01 T Parts set is an original spare parts sprue for the BT-01 chassis, bringing together key structural pieces used around the suspension and body mounting areas. Molded in black and supplied as a single T runner, the set gives a direct source for replacing worn, damaged or missing chassis parts while keeping the fit aligned with the BT-01 platform. Alongside suspension arms, the sprue carries body mounts, bumpers and damper shafts, plus further related pieces formed as part of the same runner. The image layout shows mirrored left and right components, support posts, mounting sections and smaller braces, which helps identify each part before installation. This kind of grouped spare set is useful when several connected areas need attention at once, rather than replacing only one isolated piece. As an original spare part from Tamiya, it is intended to match the chassis design named in the data rather than serve as a universal RC car part. On the bench, the set suits routine maintenance after repeated running sessions, impact damage or a rebuild of a BT-01 chassis. It also helps keep a parts box stocked with core replacement pieces that are often needed around suspension and body support points.  Warning! Not suitable for children under 14 years.

Shock absorbers & springs

Bumper Ford Ranger Subaru Brat model spare part

€19.99

This replacement bumper supports repair and upkeep on selected Tamiya vehicle builds by restoring a small but visible body detail in a single swap. The part is supplied as 1 piece and is identified in the source data for Ford Ranger and Subaru Brat applications, making it a focused choice for maintenance rather than a general universal fitting. The black moulded form shows multiple mounting points and a shaped center section that align it with model assembly hardware and body attachment areas. That layout helps when sorting spares on the bench, checking compatibility during a rebuild, or replacing a missing section after use. The source data also links the part to Sand Scorcher 58441 and 58452 references, which adds another concrete route for matching it to an existing build or parts collection. As a single replacement component, it suits targeted repairs where the rest of the vehicle remains in serviceable condition. In workshop use, a dedicated spare like this keeps restoration work moving without replacing larger assemblies. It also fits neatly into labelled parts storage for future rebuilds, especially where older Tamiya models are maintained over time and original trim details need to be brought back into place.  Warning! Not suitable for children under 14 years.

Gears & motor pinions

C-Parts Gearboxguard, model spare parts for CC-01

€15.79

C-Parts Gearboxguard for CC-01 supplies replacement molded components for drivetrain and chassis-area service on a compatible model build. The black sprue format keeps the individual sections together until trimming, making it easier to identify the required shapes during a repair session at the workbench. The set is presented as model spare parts rather than a complete kit, with molded guard, housing and fastening-area forms visible on the frame. Ribbed detailing, screw holes and cylindrical mounting posts support the mechanical role of the parts once fitted into the existing assembly. Several circular pieces and hexagonal cap-like forms add further replacement coverage for the same component group, which helps when an older build needs targeted maintenance instead of a full parts change. This format suits rebuilds after wear, damage or disassembly, and it also helps keep a CC-01 chassis in running condition with matching replacement sections on hand. AreBatteriesIncluded is stated as false in the data, and no battery is included with these spare parts.

Shock absorbers & springs

C.V.A II Oil-Shock-Set Super Short, damper set

€26.49

The C.V.A II Oil-Shock-Set Super Short is a 48-piece damper set for assembling 2 extra short oil dampers for RC chassis applications. Its shortened format suits layouts where suspension space is tight or where a lower chassis ride height is needed without moving away from an oil-filled damper design. The set is supplied as 1 oil damper set and is intended for model use from 14 years. This version is designed for MF-01X chassis use and also matches the TT-02RR chassis, where it serves as kit standard equipment. The assembly diagrams show the working structure in detail: piston rods fit into the cylinders, O-rings and E-rings secure the moving parts, damper oil is filled into the cylinder, and the piston is moved through the oil to release trapped air before the cap is tightened. Spring installation is completed with dedicated adjuster parts, allowing the suspension unit to be built to the required kit setting. That sequence gives the set clear value for replacement, rebuild and chassis-specific tuning work. On the bench, the compact damper length helps when refreshing an existing suspension layout or preparing a chassis for a lower stance. For MF-01X rear use, 5x9 mm pillows, 19805611, are required separately.  Warning! Not suitable for children under 14 years.

Shock absorbers & springs

C.V.A.II Oil Damper Set Mini, RC shock set

€36.29

The C.V.A.II Oil Damper Set Mini adds an oil-filled suspension option to compatible RC chassis and brings a more tunable setup to compact model car builds. Supplied as a 2-piece set, it is designed for builders who want to replace or refine standard dampers with an adjustable unit that can be matched to different mounting positions. Each damper can be adjusted from 55 to 70 mm, giving the set a usable range for several chassis layouts named in the compatibility list. The set is suitable for TD4, TD2, DB02, DB01, DF-03, DF-02, DT-02, DT-03, F103GT, GF-01CB, TT-02B, TT-01 TYPE-E and WR-02CB. The included damper oil supports the oil-pressure design, where the internal fluid works with the spring and shaft movement to manage compression and rebound during running. This makes the set relevant not only as a replacement part, but also as a tuning step when suspension response needs to be matched more closely to the chassis setup. On a bench build, the adjustable length helps when preparing a specific front or rear suspension position before installation. During running sessions, the oil-filled construction supports more measured chassis movement over changing surfaces and through repeated direction changes. For installation, 5 mm ball heads are required separately.  Warning! Not suitable for children under 14 years.

Shock absorbers & springs

C.V.A.II Oil Damper Set Short, RC shock set

€39.49

The C.V.A.II Oil Damper Set Short brings oil-filled suspension control to a wide range of RC chassis, with 2 short dampers designed for tuning or replacement use. Its adjustable 80 to 97 mm length gives room to match the setup to different vehicle layouts, helping the suspension work with the chassis rather than against it on rough sections and changing surfaces. This set is suitable for TD4, TD2, CW-01, DB02, DB01, DF-03, DT-02 and TT-02B chassis, and the data also names Monster Beetle, Blackfoot, Lunch Box, Midnight Pumpkin, Manta Ray, Top Force, Force and Blitzer Beetle among the compatible models. That broad fit makes it useful both for restoring an older runner and for refining the handling of an active build. The oil damper format uses fluid resistance inside the shock body to smooth compression and rebound, giving a more measured suspension action than a simple friction-based setup. On the bench, the pair suits maintenance, repair and chassis-specific tuning work where damper length matters. A 5 mm ball head is required for mounting, with part 300050592 required separately, so the set can be installed with the correct attachment hardware for the chosen model.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

CC-01 B-Parts, steering servo saver spare set

€15.79

CC-01 B-Parts brings the steering and servo saver section together in one spare parts sprue, giving compatible builds a direct route back to clean mechanical function. The black injection-molded runner presents the parts in an organized layout, with larger mirrored pieces, smaller linkage forms and circular clips arranged for clear identification at the bench. This set is intended as replacement hardware for the CC-01 rather than as a complete vehicle kit, so the focus stays on the steering assembly where accurate fit matters most. Visible molded part numbers such as 8, 9, 10, 11 and 13 help distinguish the individual shapes during preparation. The runner format keeps each component attached until needed, which supports tidier handling while checking the required section against an existing build. Glossy black molded surfaces and crisp edges reflect the technical character expected from RC maintenance parts. On a repair bench, the sprue suits worn steering sections, missing servo saver pieces or a planned refresh of an older chassis. It also fits neatly into a spares collection for hobby work, where keeping the correct CC-01 steering parts close at hand can shorten downtime between rebuild sessions.

Other spare parts & accessories

CC-01 D-Parts, body mount spare part

€7.99

CC-01 D-Parts is a body mount spare part set for model maintenance on the 58324 reference. The set provides 2+2 replacement parts, making it useful when original mounting points are worn, missing or damaged and the shell needs the correct support points back in place. The designation D Parts identifies this set within the CC-01 parts structure, which helps when matching replacements to an existing build or planning a repair. As a model supply rather than a general-purpose accessory, it is intended for a specific application instead of broad compatibility across unrelated chassis types. The body mount function matters at the point where the shell is positioned and secured, so using the named replacement set helps keep that connection in line with the original layout. Batteries are not included. This spare part set fits naturally into workshop tasks such as replacing lost components during a rebuild, refreshing a used chassis, or keeping matching parts on hand for future maintenance. It also works as a practical stock addition alongside other service parts for the same CC-01 reference, especially when a repair calls for the exact D Parts designation rather than a substitute.  Warning! Not suitable for children under 14 years.

Gears & motor pinions

CC-01 G-Parts, spare parts set for 58132

€17.29

CC-01 G-Parts for 58132 provide a focused spare-parts set for drivetrain service, centered on molded mechanical components used in rotational power transfer. The set brings together black injection-molded gear elements and related mounting parts that suit repair work on an existing compatible model. Visible components include multiple spur gears, bevel gears, a larger gear with an integrated vertical pinion, a round plate with screw holes, and additional small parts carried on a sprue frame. That combination points to gearbox or differential-related functions where meshing teeth, axle positions and cover placement all need to match the original layout. The larger geared part with integrated pinion supports a compact transfer step within the mechanism, while the bevel gear forms indicate angled drive movement inside the assembly. The round plate adds a fitted structural piece rather than loose hardware, helping restore the intended arrangement of the surrounding mechanism. On the bench, this set suits planned maintenance, wear-related replacement, or the completion of a drivetrain rebuild when original molded parts are no longer usable. It also works well as workshop stock for model owners who keep compatible mechanical spares ready for future service on 58132-based running gear.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

CC-01 M-Parts Toyota, model spare parts, 2 pcs

€26.49

CC-01 M-Parts Toyota is a spare parts set for model work on kit 58445 and provides 2 replacement parts for the matching build. The black injection-molded frame groups the components on a single sprue, so the original shapes, attachment points and part orientation stay easy to reference during repair or rebuild tasks. The molded layout shows several distinct forms, including long curved sections, mirrored arm-shaped pieces, smaller mounting blocks and round connection elements. These details matter when a damaged section needs to be replaced with a part that matches the intended geometry of the original assembly. Because the pieces remain attached to the runner before removal, each section can be identified against the build step before cutting it free. The preformed holes and connection points support clean integration with the corresponding assembly positions in the specified model. This set fits situations such as replacing lost parts during a paused build, refreshing worn sections on an existing chassis, or keeping a stored model ready for future maintenance. In a workshop drawer or alongside a current project, the sprue serves as a direct source for matching CC-01 M-Parts Toyota components tied to kit 58445.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

CC-01 Universal Joint, model accessory for Pajero

€15.99

The CC-01 Universal Joint is a dedicated model accessory for Pajero 58132 and serves as a replacement drivetrain part where a precise rotating connection is needed. Its universal-joint design allows torque to pass between connected parts even when the angle changes, which is important on a chassis layout that moves through steering and suspension travel. Used during maintenance or repair, this component helps bring a worn drivetrain area back to a defined mechanical fit. The clear CC-01 designation keeps the application focused on the matching platform, while the Pajero 58132 reference identifies the intended model directly. That makes part selection more straightforward when servicing an existing build rather than replacing larger assemblies unnecessarily. As a single-purpose spare part, it suits bench work that focuses on keeping the drivetrain operating cleanly and consistently. In a workshop setting, the joint can be fitted during routine overhaul after extended running or when a damaged coupling starts to affect smooth rotation. It also works as a practical stock spare for model owners who maintain a CC-01 Pajero 58132 and want the correct replacement ready for the next service interval.  Warning! Not suitable for children under 14 years.

Shock absorbers & springs

CC-02 Aluminum Damper Set, chassis upgrade

€94.99

The CC-02 Aluminum Damper Set equips a CC-02 chassis with 4 oil dampers built around lightweight aluminum cylinders. Their narrower shape compared with standard resin cylinders gives the suspension a more realistic scale appearance while the low-friction cylinder surface helps the dampers respond more cleanly across changing terrain. Assembly creates 4 dampers using cylinders, cylinder caps, O-ring caps, adjustable retainers and the included attachment parts. The instruction flow shows oil-filled construction with piston movement used to release trapped air before the cylinder cap is tightened, a setup that supports controlled damping rather than a simple spring-only action. Ball connectors are fitted at both ends, changing the upper mounting style used on standard CC-02 kits and allowing freer motion as the suspension works through roll. The dampers accept the chassis kit-included coil springs, and the leaflet also specifies compatibility with separately sold 12.6 x 50 mm option springs. On a trail-style CC-02 build, this set suits builders aiming for a more detailed underbody view and a more fluid suspension response over ruts, stones and side-to-side weight transfer. It also fits tuning-focused rebuilds where the damper layout is being updated without changing the chassis platform itself.

Other spare parts & accessories

CC-02 LF 6mm Ball Collar (18), chassis parts

€21.19

The CC-02 LF 6mm Ball Collar set adds a focused drivetrain and suspension upgrade to CC-02 chassis cars by replacing kit-standard C9 parts with low-friction steel components. Each collar uses a plated surface to minimise resistance where moving parts pivot and slide, so link-arm action feels cleaner and more direct when the chassis works over uneven terrain. The pack includes 18 collars in total. Of these, 16 are assigned to the link arms, while 1 fits the steering linkage and 1 fits the battery plate, giving the set a chassis-specific layout rather than a generic hardware mix. The 6 mm size matches the stated fitment, and the steel construction brings a precise contact surface to the suspension hardware. In rigid suspension setups, that lower resistance helps the links move with less drag through their travel, which supports more consistent articulation across rough sections. Installed on a CC-02 build, the collars suit tuning sessions that focus on suspension response and chassis control rather than cosmetic changes. They also fit maintenance work where worn standard parts are being swapped for smoother-running hardware in the steering and link assemblies.

Axes & drive shafts

CC-02 SS Adjust Tie-Rod Set, chassis accessory

€23.99

The CC-02 SS Adjust Tie-Rod Set adds a more tunable steering linkage to compatible CC-02 chassis cars by replacing the standard rigid molded link with stainless steel turnbuckle shafts. That change brings toe angle adjustment into the setup, allowing the chassis to be dialed in with greater precision for different running conditions and handling preferences. The set includes 1 x 104 mm stainless steel tie-rod, 1 x 53 mm stainless steel tie-rod, adjusters, and small attachment parts. The turnbuckle shafts feature hex adjustment sections, so length can be changed with a wrench as shown in the set documentation. This mechanism makes it possible to alter the linkage length directly through the shaft rather than removing and replacing a fixed rod. Stainless steel construction gives the main rods a durable metal format suited to repeated setup changes on the chassis. Installed in place of the standard kit linkage, the set supports fine setup work when steering response needs a more exact toe setting than the stock molded part allows. It suits bench tuning, rebuilds, and upgrade work on CC-02 based builds where adjustable linkage geometry is part of the chassis setup.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

Chassis Protective Sticker, RC accessory, 0.3 mm

€15.79

This hard protective film is made for the underside of an R/C vehicle chassis, where repeated contact with the track surface can leave marks during regular running. At 0.3 mm thick, it adds a thin sacrificial layer that takes the abrasion while leaving the chassis itself covered. The transparent finish keeps the visual character of the model unchanged. The sheets measure 180 x 330 mm and come in a pack of 2, providing material that can be cut to suit different chassis shapes and lengths. The highly adhesive surface is intended to bond securely under the main chassis, where constant rubbing and sliding place the greatest demand on protection. Because the film is supplied as full sheets rather than pre-cut sections, it can be adapted to a wide range of R/C vehicle layouts. This makes it useful both for a fresh application and for replacing worn film after repeated use. In workshop preparation, the film can be trimmed before a run and applied to the areas most exposed to scraping. After track sessions on abrasive surfaces, the protective layer helps keep the underside cleaner in appearance and reduces direct wear on the chassis base.

Other spare parts & accessories

Craft Tweezers, papercraft tool, 140 mm

€22.49

These craft tweezers are designed for papercraft work, where small tabs, narrow folds and glued sections need controlled handling. At 140 mm in length, they offer a compact format that sits easily in the hand while keeping the tip visible during close, detailed tasks. The foremost part uses an original TAMIYA design created to improve effectiveness in gluing, paper bending and the drying process. That shape helps hold and guide thin paper parts with more control than fingertips alone, especially when working along edges, corners and tight contact points. The tweezers are made from SUS410 stainless steel and finished with a hairline surface, giving the tool a precise, clean look suited to bench work and hobby tables. The pointed, angled form also helps reach into small spaces between folded sections without covering the working area. Sticker and decal application is another practical use, particularly when small markings need careful placement before final pressure is applied. On a papercraft build, during detail finishing, or while handling delicate printed parts, these tweezers support steady, accurate movements across each step of the work.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

Cup Joint Universal Shaft for TT-01 DF-02

€21.29

This Cup Joint Universal Shaft is a drivetrain spare part for TT-01 and DF-02 chassis setups, built to work at the gearbox in combination with an assembly cardan shaft. The pot joint design is intended to suppress drive losses, supporting smoother running when the drivetrain is under power. The set contains a left and a right part, giving the specified pair needed for the matching drivetrain layout. Its application is clearly defined for use with the DF-02 Assembly Universal Shaft 53791 or the Assembly Universal Shaft for TT-01 and TA04 53792. That makes it a focused choice for maintenance, replacement, or a driveline setup built around those universal shaft systems. The compact metal parts are shaped for precise fit within the transmission area, where clean engagement matters for consistent rotation. On the bench, this kind of component belongs in rebuilds, wear-part replacement, or a planned drivetrain update on compatible chassis. In running use, the gearbox connection and universal shaft pairing support a more fluid transfer of drive through the system, especially where a correctly matched left and right set is required.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

D-Parts F/R Upright, model spare part, 1 pc.

€14.49

D-Parts F/R Upright is a model spare part for selected Tamiya vehicle builds and is supplied as 1 piece. The molded black component is shaped for front and rear upright use, making it a practical choice when an original part from a compatible chassis setup needs replacement during maintenance or repair. The part is specified for compatibility with 58321, 58232 and 58256. Its form combines mirrored upright sections with circular housings, angled support arms, fastening holes and molded connection points in a single unit. That layout matters during repair work because the geometry of an upright part affects how surrounding running gear components line up and mount. Replacing a worn or damaged section with the correct designated part helps restore the intended fit within the assembly area. This spare part suits workshop stock for ongoing model upkeep, rebuilds after heavy running, or the completion of an older chassis that needs the original designated component. Kept alongside other maintenance parts, it supports faster repairs when a compatible model returns to the bench for service or parts replacement.

Shock absorbers & springs

Damper Bag BF1-8, spare parts set for 58441/58452

€44.99

The Damper Bag BF1-8 is a spare parts set for the Tamiya references 58441 and 58452, bringing 28 damper-related components together in one pack for targeted maintenance work. Silver tube sections, rods, caps, bushings and translucent spacer rings form a compact hardware assortment that suits repair tasks where the original suspension parts need replacement. The included contents are listed as 1 damper set with 28 pieces, making the pack a focused source for the small components that are often needed during servicing. The BF1-8 designation helps identify the correct parts group for the stated model numbers, which is useful when matching replacement hardware to an existing build. The mix of metal-look and molded parts shown for the set points to several connection and spacing functions within the damper assembly rather than a single loose replacement part. On the workbench, this set fits routine model upkeep, rebuilds after wear, or the replacement of lost small parts during disassembly. For compatible 58441 and 58452 builds, the grouped contents make it easier to restore the damper area with matching pieces kept together in one set.  Warning! Not suitable for children under 14 years.

Shock absorbers & springs

Damper Bushing, model spare part set of 8

€12.29

This set provides 8 damper bushings for model maintenance and replacement work, giving matching inserts for assemblies that use this compact flanged format. Each piece is shown in black with a cylindrical body, a central hole and a lip on both sides, a shape that supports seated placement in the intended mounting point. The small format makes the set useful when a worn insert needs to be exchanged or when spare bushings are kept ready alongside other service parts. Because all 8 pieces share the same form, the pack supports consistent replacement across the same assembly area. The through-hole design suits fastening or guided pass-through where the matching model layout calls for a bushing, while the flanged edges help the part sit in place within the corresponding opening. On the workbench, this kind of spare part belongs in regular upkeep for model vehicles and related mechanical builds that use damper-mounted components. The set can be used during repair sessions, rebuilds or planned maintenance, where fresh bushings help return the intended fit of the original assembly.  Warning! Not suitable for children under 14 years.

Screws & ball head screws

DB-01 3mm Thin Alum. Lock Nut, RC accessory

€9.79

The DB-01 3mm Thin Alum. Lock Nut set adds a compact aluminum fastening option to compatible RC chassis, with 5 blue anodized lock nuts included in the pack. The 3 mm format suits platforms that use this hardware size, and the thin profile helps when surrounding parts leave little room for a taller nut. This set is intended for a broad list of chassis named in the data, including DB01, DB02, DN-01, F104PRO II, F104Ver.II PRO, F104W, F104, M-08 CONCEPT, TA07 MS, TA06 MS, TA06, TA06 PRO, TB-Evo.7, TC-01, TRF503, TRF502X, TRF420X, TRF420, TRF419XR, TRF419X, TRF419, TRF211XM, TRF201XMW, TRF201, TRF103, TRF102, TRF101, XV-02PRO, XV-01 Chassis, XV-01 PRO and XV-01T. Aluminum construction reduces weight compared with standard metal hardware, while the lock-nut form is made for fastening duties on running chassis. For workshop maintenance, rebuilds or detail-focused upgrades, the 5-piece set provides matching hardware for multiple mounting points on one chassis. The blue anodized finish also gives exposed fastening points a more technical appearance on race-oriented and off-road builds.  Warning! Not suitable for children under 14 years.

Screws & ball head screws

DB-01 5mm Heavy Duty Adjuster, spare part, 8-pack

€6.39

The DB-01 5mm Heavy Duty Adjuster set supplies 8 matching spare parts for maintenance and rebuild work on compatible model assemblies. Each adjuster is specified with a 5 mm ball end and a 25 mm length, giving a clearly defined replacement dimension when an existing linkage needs the same format again. The set is described as a heavy duty version, making it a direct choice when the required part callout is DB-01 and the 5 mm, L=25 mm specification is needed. The scope of delivery contains 8 ball head pans, which supports replacing several worn connection points at once or keeping identical parts ready for later service work. The repeated format across all 8 pieces also helps maintain a consistent setup across the same mechanical area. On the workbench, this set fits naturally into routine repair, parts sorting and planned upkeep of a DB-01 build. Matching dimensions make comparison with removed hardware straightforward, and the 8-piece quantity suits both immediate replacement and keeping reserve parts on hand for future maintenance.  Warning! Not suitable for children under 14 years.

Screws & ball head screws

DB-01 5x5mm Al.Ball Connector, model accessory

€18.79

The DB-01 5x5mm Al.Ball Connector set adds a precise moving joint to compatible model assemblies, combining lightweight aluminum construction with a fluorine coating for smooth, lasting action at the linkage point. Each connector uses a spherical head, narrow neck and threaded shaft layout that suits pivoting connections where clean movement and repeatable fit matter. A fixed 4 mm distance from the seat bottom to the cushion ball gives this hardware a defined geometry for suspension setup changes, opening a wider adjustment range than a standard unspecified fit. The hexagon head supports firm tool engagement during installation, which helps when tightening small hardware into a chassis or suspension mount. The set contains 5 matching connectors, making it suitable for replacing worn parts or keeping identical hardware across several connection points. The metallic finish and compact 5x5 mm format suit detailed maintenance work where small differences in fit can affect movement. On a workbench, these connectors suit rebuilds, tuning sessions and routine parts replacement on a DB-01 based setup. They also fit neatly into a spares box for trackside servicing when linkage hardware needs a quick swap to restore smooth articulation.  Warning! Not suitable for children under 14 years.

Screws & ball head screws

DB-01 5x5mm Ball Connector, RC chassis part

€18.29

The DB-01 5 x 5 mm aluminium ball connector adds a compact adjustment point to compatible R/C chassis and supports more precise upper arm positioning where setup changes matter. Its blue anodised finish and hex head format give the small hardware piece a clean technical look while keeping installation focused on a defined mounting point. This version reduces the length from the bearing surface to the ball joint from 5 mm to 4 mm, increasing the available adjustment range on competition-capable chassis. The connector is manufactured from high strength aluminium and uses a threaded shaft with a rounded ball head for linkage attachment. A hexagonal hole accepts a 2 mm wrench for controlled tightening, and the instruction sheet notes that spacers can be used if needed to adjust position further. Compatibility covers a broad list of platforms including DB02, F104Ver.II PRO, FF-04 EVO, M-07 CONCEPT, M-08 CONCEPT, TA07 PRO, TA08 PRO, TB-04, TB-05 PRO, TC-01, TRF419, TRF420, TT-02 TYPE-S and XV-02PRO. In workshop use, this hardware suits rebuilds, replacement of worn mounting points and setup revisions across touring, formula and rally chassis in the supported range. The pack contains 5 ball heads, allowing several connection points to be updated in one session.  Warning! Not suitable for children under 14 years.

Screws & ball head screws

DB-01 5x5mm Steel Hex Head Ball Connector Set

€14.99

The DB-01 5x5 mm Steel Hex Head Ball Connector set adds a precise metal connection point to RC chassis assemblies where compact hardware and clean fit matter. With 5 matching parts in the pack, it suits repair work, routine maintenance and fresh builds that need consistent ball-end mounting points in a small format. Each connector uses a threaded screw shaft below a flange and rounded ball top, a layout commonly used where a linkage, rod end or ball cup needs to pivot around a fixed point. The 5x5 mm dimensions support installation in tight spaces, while the hex head format helps with controlled fitting during assembly or replacement. High-strength steel gives these connectors the material basis for demanding off-road use, and the same parts can also be installed in on-road chassis. In workshop use, this set supports quick replacement of worn connection hardware on compatible RC models and keeps matching spare parts ready for setup changes. The pack contains 5 ball heads. With compatibility stated as any chassis, the set can serve as a useful stock hardware option across different model car platforms and parts boxes.  Warning! Not suitable for children under 14 years.

Screws & ball head screws

DB-01 5x8 mm Ball Connector, RC chassis part

€18.29

The DB-01 5x8 mm Al.Ball Connector set brings a compact aluminium tuning part into suspension setup work on compatible RC chassis. Each connector uses a blue anodized finish and a 5x8 mm format, creating a clean fit for linkage points where precise geometry changes matter during maintenance and track preparation. A key detail lies in the revised distance from the seat bottom to the cushion ball, reduced from 5 mm to 4 mm. That change broadens the available suspension adjustment range and opens finer setup steps than a standard layout allows. The hexagonal hole type supports secure tightening, so each connector can be installed with firm tool engagement rather than relying on a plain slot or rounded head. The set contains 5 ball heads, giving enough hardware for targeted replacement work or coordinated changes across multiple mounting points. Compatibility is stated for the TA05, TRF415MSX and TB Evolution IV chassis, making the set a focused choice for workshop stock, rebuilds and setup revisions on those platforms. During routine servicing, the compact dimensions and defined fit help keep suspension links moving through their intended range while supporting repeatable adjustment work.  Warning! Not suitable for children under 14 years.

Screws & ball head screws

DB-01 Ball Head Connector, RC spare part, 5x8 mm

€14.99

The DB-01 5x8 mm Ball Head Connector set adds a compact steel mounting point wherever an RC chassis needs a snap-on linkage connection. Each of the 5 connectors combines a spherical ball head, a short neck and a threaded shaft, creating a clean interface for articulated parts that need controlled movement during running and setup work. The 5x8 mm dimensions make this hardware easy to match to existing assemblies when worn connectors need replacement or a fresh build calls for uniform fittings across several mounting positions. High-strength steel gives these parts the material basis for demanding off-road racing use, where repeated movement and chassis loads act directly on small connection points. The same connector format can also be installed on on-road chassis, so one pack covers more than a single vehicle type. Scope of delivery: 5 ball heads. In workshop use, the set suits routine maintenance, rebuilds after heavy track sessions, or stocking spare hardware for race-day repairs. The compact size also makes it practical for builders who want matching connector geometry across steering links, suspension links or other articulated mounting points that use this format.  Warning! Not suitable for children under 14 years.

Screws & ball head screws

DB-01 Dust Cover Ball Head Adjuster Set 20pc

€5.39

The DB-01 Dust Cover Ball Head&Adjuster(20) is a general use option part made to protect the connection joints between ball connectors and adjusters in the suspension system. By covering these exposed joint areas, it helps maintain smooth suspension operation during repeated use and supports more consistent movement where the linkage needs to articulate freely. This set contains 20 dust covers and is intended for chassis maintenance, replacement work and fresh builds that use ball connector and adjuster linkages. The part focuses on the joint itself rather than the whole suspension assembly, adding protection exactly where dirt and wear can affect the connection. Its general use design makes it suitable across a broad range of compatible model chassis rather than limiting fit to a single platform. In workshop use, the covers can be fitted during routine servicing when suspension links are checked, cleaned or renewed. They also make sense as spare stock for rebuilds, tuning sessions or keeping several chassis ready for running with protected linkage points. Compatible with any chassis.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

DB-01 Fluorine Coated Suspension Balls, RC parts

€16.79

DB-01 Fluorine Coated Suspens. Balls(8) is a suspension hardware set for RC chassis tuning and maintenance. The fluorine coating reduces friction between each suspension ball and its mount, which supports more fluid suspension movement when the chassis changes direction, settles into corners or reacts to surface input. The scope of delivery contains 8 balls for wishbone shafts, making this set suitable for replacing worn contact points with matching hardware across the suspension assembly. Compatibility reaches across several Tamiya chassis families: TA06, TA06 PRO, TA06 MS, TB-03 VDS and TA05 ver.II use these balls with 54064-54074 and 54171-54175. FF-03, FF-03 PRO, TB-03, TB-04 and TB-04 PRO use them with 54064 to 54074. M-07 CONCEPT and M-08 CONCEPT use them with 54760, while TC-01 uses them with 54760 and 54787. This suspension set suits regular workshop servicing, chassis refreshes and targeted setup work where smooth ball-to-mount movement matters. It also fits neatly into a spares box for track days or bench maintenance, with 8 matching pieces ready for the specified chassis applications.  Warning! Not suitable for children under 14 years.

Gears & motor pinions

DB-01/TRF501X Pinion Gear 24/25T 48DP Set

€16.79

The DB-01/TRF501X Pinion Gear 24/25T 48DP set adds a focused drivetrain tuning option to compatible RC chassis with 2 metal pinion gears in 24T and 25T sizes. The 48 pitch format and newly designed tooth profile are intended to reduce noise and friction loss, supporting a cleaner mesh and a smoother running feel during track sessions, maintenance work or ratio changes. Each gear uses 2 grub screw attachment holes, so the fastening position can be selected during installation on the motor shaft. The set also comes with 3 grub screws and an L-shaped hex key for fitting and adjustment. This makes the set useful both as a replacement for worn drivetrain parts and as a practical gearing option when refining acceleration, response or running characteristics on a supported chassis. Compatibility covers DB01-Chassis, DB02-Chassis, DN-01-Chassis, TD2-Chassis, TD4-Chassis, TRF201-Chassis, TRF201XMW-Chassis, TRF211XM-Chassis and TRF502X-Chassis. For TD2-Chassis and TD4-Chassis, use with 22031 is required. On the bench, the 24T and 25T choice allows quick comparison between 2 gearing steps while keeping the same 48DP standard across the setup.  Warning! Not suitable for children under 14 years.

Gears & motor pinions

DB-01/TRF501X Spur Gear, RC spare part, 91T 48DP

€6.99

The DB-01/TRF501X Spur Gear 91T 48DP is a dedicated RC spare part for compatible drivetrain setups, combining a 91-tooth count with a 48 pitch tooth profile for precise transmission matching during maintenance or repair. Built for use with the DB01 and TF503 chassis named in the data, it gives the drivetrain a clearly specified replacement component rather than a generic gear. The 91T layout determines the driven gear size within the transmission, while the 48DP format identifies the fine tooth pitch used for correct meshing with the matching pinion. That makes this gear relevant when restoring the original gearing arrangement on a compatible chassis after wear, damage or routine workshop service. As a model supply in the Models & Accessories range, it suits bench work focused on drivetrain upkeep rather than cosmetic changes. The listed designation DB-01/TRF501X also helps place the gear within specific RC platform families. In practical use, this spare part belongs in the workshop alongside other transmission service components for compatible off-road chassis builds. During maintenance sessions, it supports a straightforward parts swap that keeps the drivetrain specification aligned with the stated 91T 48DP format for continued running on the correct platform.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

DF-02 B-Parts Upright/Steering Arm Spare Set

€14.29

DF-02 B-Parts Upright/Steering Arm is a chassis spare set for the DF-02 and TT-02B platform, built to restore key steering and wheel support points with matching replacement components. The black molded parts are arranged as 4 sprues with 20 pieces, making this set a practical choice when worn or damaged suspension and steering sections need to be renewed. The upright and steering arm shapes handle pivot and linkage mounting duties within the front end layout, while the mirrored forms support correct left and right installation. Multiple mounting holes are formed into the parts for chassis attachment and linkage connection. The set also includes 4 wheel nuts and 8 washers, adding the fastening hardware needed for the relevant assemblies. As a dedicated spare set, it suits routine maintenance, repair work after running sessions, or keeping workshop stock ready for future rebuilds. On the bench, the parts help bring a DF-02 or TT-02B chassis back into running condition with matching replacement geometry instead of mixed substitutes. For hobby maintenance, rebuild projects, or replacing damaged steering components after track use, this set keeps the fit focused on the specified chassis types.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

DF-02 Drive Shaft Set, RC spare part, 64 mm

€13.29

This DF-02 Drive Shaft set provides a direct spare part solution for the DF-02 chassis and includes 2 drive shafts with a stated length of 64 mm. The matching pair format suits maintenance work where both sides of the drivetrain need the same part specification, keeping the assembly consistent across the axle setup. Each shaft follows a straight cylindrical form with ball-shaped ends and cross pins for connection at the mounting points. That layout is designed for mechanical transfer within the drivetrain while matching the geometry required by the DF-02 platform. The black finish and compact rod profile make the parts easy to identify during a rebuild or parts check. As replacement components rather than a general accessory, these shafts are intended for the named chassis application instead of broad multi-model use. The set fits routine workshop tasks such as replacing worn transmission links during servicing, refreshing a stored chassis before running, or keeping matching spare parts ready for a future repair. In a bench setup focused on DF-02 maintenance, the 2 included shafts cover a complete paired change with the specified 64 mm dimension.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

DF-02 E-Parts, spare parts set, wheel axle

€9.79

The DF-02 E-Parts set provides replacement components for the wheel axle and differential joint area, giving compatible model maintenance a direct route to restoring key drivetrain connections. Black moulded parts are supplied on sprues, with the axle-related and joint-related sections grouped for clear identification before removal and fitting. This spare parts set is designated as E Parts for 58328 and is intended for focused servicing rather than broad replacement across unrelated assemblies. The visible component mix includes cylindrical axle-linked pieces, connector forms and longer structural elements that belong to the same parts tree. Keeping these pieces together on one runner helps confirm part shape and orientation during workshop preparation. The set format also suits repair benches where damaged drivetrain sections need matching replacement geometry from the original parts family. Used during maintenance, rebuilds or parts replacement after wear, the DF-02 E-Parts set supports continued running with the correct component group kept on hand. It fits naturally into a spares collection for model upkeep, especially when the axle and differential connection points need renewed parts to return a chassis to working order.  Warning! Not suitable for children under 14 years.

Gears & motor pinions

DF-02 Metal Parts Bag A, model spare parts

€30.49

DF-02 Metal Parts Bag A is a model spare parts set identified in the source data for 58328. The designation points to a defined replacement pack rather than a general accessory, making it a practical choice when an existing build needs the matching hardware group restored or completed. The stated metal construction gives this set a clear material identity, while the DF-02 naming keeps the part reference specific for workshop organisation. As a parts bag, it suits maintenance, repair and replacement tasks on a compatible build already in use. The source data places it in model supplies, which fits its role as a support component for an established model rather than a standalone vehicle or assembly kit. This also helps when sorting spares by platform and bag reference during bench work. On the work surface, a clearly named replacement pack saves time during upkeep because the part group is already narrowed to DF-02 Metal Parts Bag A for 58328. It works well as a stock spare for routine servicing, for completing an older build, or for replacing missing original metal components with the specified bag reference.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

DF-02 Universal Shaft Assembly, RC drivetrain set

€56.99

The DF-02 Universal Shaft Assembly is an RC drivetrain upgrade set built to cut friction where the axle moves through the steering angle. In place of a standard dog bone drive shaft, the universal joint layout keeps power delivery more direct while the front end changes direction, which helps the chassis carry drive more cleanly through bends and technical sections. The set contains 1 ball cardan shaft set with 13 pieces and is built around 2 universal shafts. Visible components include wheel axle parts, cross joints, pins, grubscrews, AW grease and a hex wrench for assembly. The shafts are marked 70, and the document notes grease application at multiple moving contact points in the joint and cup areas. The assembly is designed to be taken apart again, which allows consumable parts to be replaced when wear appears instead of discarding the full shaft unit. Fitment is specified for DF-02, DT-02, DT-03, DT-03T and TT-02B chassis with the matching cup joints listed in the data. On a buggy set up for repeated steering input, jumps and direction changes, this drivetrain layout supports a more consistent feel at the driven axle and gives maintenance-focused builders a clear upgrade path within compatible Tamiya chassis.  Warning! Not suitable for children under 14 years.

Shock absorbers & springs

DF-03 B-Parts Damper Stay, chassis spare part

€11.99

The DF-03 B-Parts Damper Stay set is a chassis spare part made for the DF-03 platform and supplies front and rear stay components in one pack. Its molded black parts follow the original mounting pattern, so repair work can focus on restoring the suspension mounting area with the correct fit for this chassis. Several hole positions are built into the stays, giving the assembly clear fastening points where dampers and related hardware attach. Ribbed reinforcement details are formed into the parts, and the set also shows a metal brace element fixed with screws and washers for added structure in the mounting section. This combination suits routine maintenance, replacement after wear, or rebuilding a used chassis with the proper B-parts section rather than mixing unmatched components. On the bench, the set supports a straightforward refresh of damaged front or rear mounting points on a DF-03 build. It also fits parts storage for racers and hobby workshops that keep chassis-specific replacements ready for service between running sessions.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

DF-03 Chassis, RC spare chassis frame

€13.99

The DF-03 Chassis serves as the structural core for a compatible RC vehicle build, forming the main lower frame that carries the mechanical layout. Its black molded construction combines an elongated central body with raised side sections, giving the assembly a defined platform for attaching major modules while keeping the underside compact and purposeful. Across the frame, multiple drilled and countersunk mounting holes create fixed attachment points for screws and hardware. A large oval opening in the center is joined by shaped slots and recessed areas, which help organise the placement of installed parts and leave room for routed connections within the chassis layout. One end uses a rectangular mounting section with 4 visible countersunk holes, while the opposite end extends into a flat plate with additional drilled points for further fitment. These details make the frame more than a simple base plate: it establishes the geometry that the rest of the DF-03 build follows. Used as the lower platform in a rebuild, repair or replacement project, this chassis frame supports a clean restart when an existing vehicle needs a fresh foundation. It also suits workshop stock for keeping a compatible DF-03 machine in running condition after wear or damage to the original frame.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

DF-03 D-Parts Rear Upright Hub Carrier Set

€9.59

The DF-03 D-Parts Rear Upright Hub Carrier set is a chassis-specific replacement set for the DF-03 platform, supplying the molded parts used in the rear upright and hub carrier area. With 1 D parts tree and 6 parts in the box, it gives the build a direct source for the designated components when maintenance, rebuild work or part replacement is due. The set is focused on one defined chassis section rather than a mixed hardware assortment, which keeps part selection clear during workshop use. The molded layout on the runner helps identify each piece before removal and fitting, especially when comparing worn parts against fresh replacements. Because the set is tied to the DF-03 chassis, it suits repairs that need the matching geometry and mounting form for that platform. The rear upright and hub carrier area plays a key role in how the corresponding rear assembly is put together, so using the intended parts helps restore the specified structure of that section. On the bench, this set fits naturally into routine servicing, rebuilds after heavy running, or a planned stock of spare chassis parts. It also works well as a replacement pack to keep alongside a DF-03 model, so the required rear section components are on hand when a damaged part needs to be exchanged.  Warning! Not suitable for children under 14 years.

Gears & motor pinions

DF-03 Gear Parts Bag, RC spare parts set

€39.99

The DF-03 Gear Parts Bag for 58370 focuses on one of the most important working areas in an RC drivetrain: the differential. This spare parts set brings together the core service components needed when the original assembly shows wear, so the drive system can return to clean, controlled power delivery under load. The set is presented as a dedicated bag for the DF-03 and, based on the included contents, covers the internal differential hardware rather than general chassis maintenance. Visible parts include a large metal gear with shaft, a smaller metal gear, 2 black outdrives, 2 black differential housings or cams, 4 large shim washers, additional small shims and washers, 2 metal pins, 2 groups of ball bearings, 6 white bushings or spacers, 4 coil springs, and a tube marked Ball Diff Grease. That combination supports rebuild work, replacement of worn running parts, and fine adjustment of the differential stack. On the bench, the mix of gears, bearings, shims and grease gives a clear route for servicing a used transmission assembly or refreshing a stored chassis before the next run. As a model-specific spare parts bag for 58370, it also helps keep maintenance organised when a DF-03 build needs the correct drivetrain components close at hand.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

DF-03Ra Assembly Universal Shaft RC Parts Set

€35.49

The DF-03Ra Assembly Universal Shaft brings a serviceable drivetrain upgrade to compatible RC chassis, combining a ball cardan shaft layout with high-precision machining that reduces the stalling feel during steering and supports smoother cornering. In the workshop or at the track, the metal shaft parts, pins and couplers form a focused tuning set for driveline maintenance and response. The scope of delivery contains 1 ball cardan shaft set with 13 pieces. Visible set contents include 2 long shafts marked 39, joint hardware, pins, set screws, an L-shaped hex key and AW anti-wear grease for the moving contact points. The PTO shaft can be assembled and disassembled, which allows worn consumable parts to be exchanged instead of replacing the whole assembly. That serviceable layout helps keep the driveline working with the same intended action over repeated running sessions. Compatibility is specified for TT-02 chassis, TT-02D chassis, TT-02FT chassis, TT-01 TYPE-E chassis and TT-01D TYPE-E chassis when combined with the listed companion parts. This makes the set suited to targeted repair work, drivetrain upkeep and handling-focused tuning where steering load and cornering smoothness matter most.  Warning! Not suitable for children under 14 years.

Gears & motor pinions

Diff. Gear Bag Grasshopper Hornet Spare Parts

€6.49

This spare parts set is made for differential service on compatible Grasshopper and Hornet RC models. Supplied as a 6-piece gear bag, it focuses on one specific drivetrain area and gives repair or rebuild work the matching gears needed for a direct replacement task. The set belongs to the model supplies range and is intended for maintenance rather than first-time vehicle assembly. By concentrating on the differential section, it helps address wear in a part of the drivetrain that affects power transfer during running. The bag format keeps the relevant gears grouped together for workshop use, whether the job involves replacing worn parts or refreshing an older compatible chassis. Compatibility is stated for Grasshopper and Hornet, so the set can be selected for those named models without adding unrelated universal-fit claims. On the bench, this kind of replacement set fits routine upkeep, targeted repairs and parts storage for future service work. It is a focused choice for RC model maintenance where the differential needs the correct matching gear components rather than a general mixed spares assortment.

Other spare parts & accessories

DN-01 Inner Sponge Front Kit, foam insert set

€6.69

DN-01 Inner Sponge Front Kit is a front foam insert set for selected buggy chassis, built to sit inside the front tyres and support their shape while the model is running. The set contains 2 grey open-cell foam rings and is specified for DT-03, DT-03T and DT-02 chassis applications. Inside the tyre, each insert fills the cavity between tyre and wheel so the front end keeps a more defined profile as loads shift through steering inputs and uneven ground. The donut-shaped foam form shown in the set is intended for front use, which matters when tuning the balance of a buggy around turn-in and directional control. Compatibility is stated with tyre references 51207 and 54284, giving a clear match point when replacing worn inserts or building a fresh wheel and tyre setup. The foam material also keeps the setup light compared with heavier internal fillers. This 2-piece set suits routine maintenance, a chassis refresh or a second wheel set prepared for another surface. On a running DT-03, DT-03T or DT-02 build, fresh front inserts can help restore a more even tyre profile after repeated use and compression.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

Double-Sided Tape 20mm x 2m, black tape roll

€14.79

This black double-sided tape gives R/C model work a clean, practical way to mount and protect equipment in one step. The 20 mm x 2 m format provides a continuous roll that can be trimmed to the exact length needed, whether the task calls for a short fixing point or a longer contact strip across a wider surface. Its heat-resistant construction suits model layouts where mounted components sit close to running electronics and need a dependable adhesive layer between parts and the chassis or mounting surface. The foam-style tape profile also helps create a slight buffer where equipment needs both attachment and a degree of separation from the surface below. Compared with pre-cut strips, the roll format keeps sizing flexible during bench work and repeated maintenance. It can be cut for receiver boxes, electronic modules or other onboard components where tidy placement matters. One roll is included.

Axes & drive shafts

Drive Shaft, RC spare part, steel, 45 mm

€12.99

This RC spare part supplies 2 steel drive shafts at 45 mm length for model vehicle drivetrains that use ball differential drives. The shaft format matches Manta Ray and Fire Dragon applications named in the data, giving a direct way to replace worn drivetrain links while keeping the intended mechanical layout in place. Each shaft uses a long steel rod with formed ends that sit into the drivetrain connection points, where rotation is passed through the linked assemblies. The 45 mm measurement matters in this role because shaft length determines how the connected parts line up during running. With 2 identical pieces in the pack, both sides can be fitted with the same specification instead of mixing different lengths or constructions. The part is listed for bowling and ball differential drives, so the stated drivetrain type stays clear when selecting the replacement. This kind of spare part suits repair work, routine maintenance and the refresh of an older chassis that needs the original shaft format restored. It can also be paired with the matching ball cardan shafts named in the data when a compatible drivetrain setup is being completed with related components.

Axes & drive shafts

Drive Shaft, spare part set for 58087 model

€13.99

This spare part set provides 2 drive shafts for model 58087 and focuses on one clear job: replacing the matching drivetrain components with the correct designated parts. The shafts shown combine a long metal rod with white end connectors and protruding metal pins, giving the assembly the connection points needed for the intended mounting position. As a dedicated replacement set, the value lies in fit and function for the specified model rather than in generic compatibility. The 2-piece format suits repairs where both corresponding shafts are changed together, and it also supports planned maintenance when worn drivetrain parts need renewal. The metal rod section forms the main shaft body, while the molded end pieces create the shaped interfaces required by the assembly. This keeps the repair focused on the exact component group named in the set. On the workbench, these drive shafts suit routine servicing, rebuilds after wear, or the completion of an unfinished model that is missing original running parts. For collectors and builders maintaining model 58087, the set supplies the exact replacement category needed for a clean, model-specific repair.  Warning! Not suitable for children under 14 years.

Shock absorbers & springs

DT-01 Damper Bag, RC spare part for 58205

€14.89

The DT-01 Damper Bag for 58205 is an RC spare part set built around 4 matching suspension units with red molded bodies, silver coil springs, inner rods and mounting eyelets at both ends. These parts are shaped to connect directly into the suspension layout of the specified model, restoring the moving link between attachment points when the original dampers are worn or damaged. Each damper combines a cylindrical upper housing with a visible spring wrapped around the center section, plus a lower end designed for secure mounting. That construction matters during maintenance because the spring and rod assembly allows controlled suspension movement instead of a fixed connection. The matching format across all 4 parts also supports balanced replacement work on multiple corners of the chassis rather than mixing different damper types. As a dedicated DT-01 spare part for 58205, the set is focused on repair, upkeep and keeping the running gear mechanically complete. On the bench, the bag suits routine servicing, rebuilds after heavy use and the replacement of missing or tired suspension parts. Once fitted, the dampers return the model to a setup with the correct spring-supported linkage for rolling, steering and general chassis movement.  Warning! Not suitable for children under 14 years.

Shock absorbers & springs

DT-02/03 B Parts, axle pad holder spare sprue

€5.49

This spare B parts set supplies the Fighter axle pad and holder components for DT-02 and DT-03 chassis work, giving repair and maintenance builds the exact molded section needed for a clean replacement. The black parts are supplied on 1 sprue, so the full group stays together until the required section is removed and fitted. The set is specified as B parts for Super Fighter G DT-02 reference 58340, which makes it a focused choice for restoring the original layout rather than substituting unrelated hardware. The sprue format also helps with bench organisation, because each connected section remains easy to inspect before trimming. The visible molded structure supports careful handling of smaller mounting areas while the remaining pieces stay attached to the runner. For workshop stock, a single replacement sprue is also straightforward to sort and store alongside other chassis-specific service parts. This set suits rebuilds after wear, damage or missing pieces, and it also fits planned maintenance when a chassis is already apart for service. On the workbench, the connected layout makes it easier to compare the replacement section with the installed part before the swap begins.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

DT-02/03 Upright L/R, RC spare part set

€10.19

The DT-02/03 Upright L/R is a dedicated RC spare part set for restoring the front end of compatible chassis builds. Supplied as left and right uprights, the set replaces the side-specific mounting pieces that support wheel assembly and connected steering or suspension movement during running. Its value lies in precise fitment for the DT-02 and DT-03 platform family, where a damaged upright can affect alignment and interrupt smooth operation. Replacing the affected parts with the correct upright pair helps bring the chassis back to its intended layout without changing unrelated assemblies. The compact parts format also suits the usual maintenance cycle of hobby-grade RC vehicles, where individual wear points are renewed as needed rather than swapping complete sections. For bench work, the set is easy to sort, store and match to the relevant repair task because the application is clearly defined in the designation. This spare part set fits naturally into routine buggy upkeep after repeated use, contact with track barriers or general wear in the front corner area. It also serves as a practical stock part in a workshop drawer, ready for scheduled maintenance or a direct replacement when a DT-02 or DT-03 chassis needs the correct upright on each side.  Warning! Not suitable for children under 14 years.

Screws & ball head screws

DT-03 3x46mm Screw Pin, model spare part

€3.19

The DT-03 3x46mm Screw Pin set supplies 4 matching replacement fasteners for compatible DT-03 model assemblies. Each pin measures 3 x 46 mm, giving a clearly defined format for maintenance work where the original hardware needs to be renewed with the same dimensions. The screw pin layout combines a long shaft with a threaded fastening function, supporting clean installation at the intended mounting point. The set format keeps all 4 pieces consistent, which helps when replacing multiple matching parts in one service session. The metal build adds the firm, precise shape needed for hardware that sits within moving chassis areas and must hold its position once installed. For workshop organisation, the pack also makes sense as a ready reserve for future wear-related replacement. On a bench setup, these pins fit naturally into routine repair jobs, partial rebuilds or the refresh of a frequently used DT-03 chassis. They also suit planned maintenance before the next running session, when matching hardware dimensions can save time and keep a build mechanically consistent.

Screws & ball head screws

DT-03 5mm Ball Connector, Servo Saver Part

€4.39

The DT-03 5 mm Ball Connector M2 for the servo saver is a small RC spare part built around a clear mechanical job: creating the pivot point where a linkage can snap or seat onto a rounded ball head and move through the steering action. Its compact shape combines a smooth 5 mm ball, a narrow collar and an M2 threaded post for screw-in installation in the matching assembly. This format suits DT-03 setups that use a servo saver connection with this size and thread specification. The spherical head gives the linkage a consistent contact point, while the threaded shaft anchors the part in place inside the steering hardware. As a replacement component, it helps restore the original connection geometry when an existing ball connector is worn, damaged or missing. The black finish and metal build match the technical look of RC running gear and fit neatly into confined spaces around steering parts. On the bench, this connector belongs in routine maintenance, rebuilds and parts replacement for compatible DT-03 assemblies. It is especially useful when refreshing steering response after wear at a frequently moving joint, or when completing a repair with the correct 5 mm and M2 specification rather than a near match.

Shock absorbers & springs

DT-03 C Parts, chassis damper stays spare set

€16.49

DT-03 C Parts provide replacement chassis and damper stay sections for selected RC model builds, with the main components supplied on a grey injection-moulded sprue for clear identification before removal. The set is intended for maintenance work, rebuilds and parts replacement where the original mounting sections need a direct-format spare. The sprue layout groups multiple structural pieces in one frame, including the chassis and damper stay elements named in the product data. That format helps keep the parts together during storage and bench work until each section is cut free for installation. The moulded construction suits the precise shapes needed around mounting points and connected assemblies. Compatibility is stated for 47347, 47371, 57872, 57895, 58587, 58628 and 84435, which gives a clear reference for matching this spare set to the correct vehicle platforms. On the workbench, this set fits naturally into routine service jobs after wear, damage or a full strip-down of the model. It also works as a practical stock spare for hobby rooms where frequently used chassis sections are kept ready for the next repair session.  Warning! Not suitable for children under 14 years.

Shock absorbers & springs

DT-03 CVA Damper Set Short/Mini RC Chassis Parts

€33.99

The DT-03 CVA Damper Set Short/Mini brings oil-filled suspension action to a range of Tamiya off-road chassis cars, replacing basic friction-style movement with a more refined damper setup. With 2 mini shock units and 2 short shock units, the set equips 1 complete chassis and gives front and rear suspension the controlled compression and rebound needed for cleaner handling on loose ground and uneven sections. Inside the set are the parts for 4 assembled dampers, including damper bodies, piston rods, springs, seals and hardware. During assembly, oil is added to each cylinder and the piston is moved slowly to release trapped air before the cap is tightened, creating the internal damping effect that defines the CVA design. Separate front and rear assemblies use different parts and oil seals, and spring spacers are fitted to adjust preload after the springs are installed. The dampers mount to the chassis in the same way as the standard kit units, so the upgrade stays focused on suspension behavior rather than a change in layout. Compatibility covers DT-03, DT-03T, DT-02, TT-02B and DF-02 chassis cars, which makes the set useful for repair, replacement or tuning across several established platforms. On a buggy or off-road build, that means a more settled response through bumps, jumps and rough sections where suspension consistency shapes how the chassis tracks and lands.  Warning! Not suitable for children under 14 years.

RC spare parts

DT-03 E Parts Upper Arm, RC spare part set

€6.49

The DT-03 E Parts Upper Arm set supplies the suspension pieces needed when a DT-03 chassis calls for a direct replacement. Each molded arm remains attached to the black runner, making the parts easy to identify before trimming and fitting into the existing assembly. The set contains 2 mirrored upper arm components in a 1+1 configuration, shaped for opposite sides of the suspension. Hinge mounting points are molded at both ends of each arm, and the elongated profile includes open reinforcement sections that match the original part layout. The visible E marking on the sprue helps confirm the correct section during a rebuild or when sorting spares at the workbench. As a dedicated RC spare part set, this pack focuses on the exact chassis area that takes repeated movement during running sessions and service intervals. It fits naturally into repair tasks after wear, damage or a full strip-down of the suspension assembly. Kept in a spares box, the fresh molded parts are ready for planned maintenance or for bringing a DT-03 build back to its intended suspension geometry with matching left and right arm pieces.

Axes & drive shafts

DT-04 B Parts Uprights, chassis spare parts

€8.99

The DT-04 B Parts Uprights set brings together molded replacement components for the new DT-04 chassis, making it easier to restore worn mounting points or replace damaged running gear with matching parts. Black resin pieces for the front and rear sections keep the fit aligned with the original chassis layout, whether the workbench task is a targeted repair or a broader rebuild. Beyond the uprights, the set covers several key connection areas of the chassis. C-hubs support the front end structure, while damper stays provide the shock mounting sections used in the suspension setup. The steering linkage transfers servo movement through the steering assembly, and the servo horn forms the connection point between servo output and linkage movement. Hex hubs complete the wheel mounting area, so the set reaches across several mechanical zones instead of covering only one isolated part. This parts group suits maintenance sessions after heavy running, rebuilds of a used chassis, or keeping workshop stock ready for future repairs. It also helps when a fresh DT-04 build needs replacement pieces on hand for the steering, suspension and hub areas most likely to see regular service.  Warning! Not suitable for children under 14 years.

Shock absorbers & springs

DT-04 Carbon Damper Stay Set, RC tuning parts

€29.79

The DT-04 Carbon Damper Stay Set adds a focused suspension upgrade to a DT-04 RC chassis with carbon fiber plates and dedicated mounting hardware. Multiple holes in the main stay and side plates create clear adjustment options for damper positions, supporting setup changes that suit different surfaces and driving styles. The set contains 1 long carbon fiber plate, 2 smaller support plates, 4 black ball studs, several screws in different lengths, 2 lock nuts with blue nylon inserts, and 2 metal washers. This combination forms a complete fitting set for the stay components rather than loose replacement pieces gathered from different packs. The carbon fiber construction keeps the parts thin and rigid, while the hole pattern allows measured changes to mounting locations. Ball studs and lock nuts support secure attachment at the specified points, and the washers help seat the hardware cleanly during installation. On a workbench, the parts layout is easy to sort before fitting, and on the chassis the stay set supports careful suspension tuning through hardware-backed position changes. It suits builders refining a DT-04 setup with a dedicated carbon fiber upgrade rather than a general cosmetic add-on.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

DT-04 Chassis blk, RC chassis part, black tub

€12.79

DT-04 Chassis blk provides the core lower frame for an RC model build, with a black molded tub shape that brings the main structure together in one substantial component. Raised sidewalls, integrated screw posts and a ribbed interior create a clear base for positioning major assemblies while keeping the layout defined on the bench. The molded underside geometry shows how this chassis part is designed to carry more than a flat floor alone. Reinforcing ribs run through the interior to stiffen the form, while circular holes and mounting points are placed directly into the tub for mechanical fastening. The extended end plate section adds another structured area with several fixing holes and ribbed supports, giving the build extra attachment space where connected assemblies need a stable anchor. As a replacement or project part, this chassis tub restores the original lower structure without changing the designated DT-04 layout. On a rebuild, repair or fresh parts-based assembly, this component sets the position for the rest of the chassis around a single molded base. The black finish matches the functional look of an RC underframe, and the one-piece construction keeps the mounting geometry together in the form intended for the DT-04 platform.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

DT-04 Full Ball Bearing Set, chassis accessory

€24.29

The DT-04 Full Ball Bearing Set adds a precise drivetrain and steering upgrade to the DT-04 chassis with 18 metal bearings in 3 sizes. Installed in rotating points across the chassis, the bearings replace plain support parts with rolling contact, which helps moving assemblies turn with less drag and a smoother mechanical feel. The set includes 4x 850, 4x 1050 and 10x 1150 bearings, matching the different mounting points used in the DT-04 layout. That size spread makes the set suitable for a complete bearing conversion rather than a partial refresh of only one section. In the drivetrain, freer rotation supports more efficient transfer of motor output through the transmission. In the steering system, the same bearing construction helps linked parts move with a more direct action at the front end. This chassis accessory suits a new DT-04 build as well as later workshop maintenance when worn parts are being replaced. The small, shielded metal bearings are arranged as a dedicated fitment set for the platform, making them a practical choice when the goal is a cleaner-running buggy with reduced mechanical resistance in its key moving assemblies.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

DT-04 M Parts, chassis mount spare parts

€11.49

The DT-04 M Parts gearbox and chassis mount set provides replacement components for RC model maintenance where structural sections need to be renewed. Supplied as black injection-moulded parts on sprues, the set is arranged for clear identification before trimming, sorting and installation. The visible parts tree contains multiple connected components shaped for functional mounting and support roles, including chassis-related sections, bracket forms and frame elements. This format helps keep small pieces together until they are needed at the bench and allows each part to be checked against the original assembly before removal from the runner. The moulded layout is suited to repair work after wear or damage, and it also supports planned rebuilds where a fresh gearbox or chassis mounting section is required. The technical presentation keeps the focus on fit, structure and correct part selection. On a workbench, the sprue format makes it easier to compare each section with the existing RC vehicle before cutting and fitting. During servicing, the set can be used to replace damaged mounting areas, refresh key structural points or prepare a stored chassis for reassembly with the correct DT-04 M components.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

E-Ring Set, model accessory, 17 pcs 2mm 3mm 4mm

€2.99

This E-Ring Set brings small but essential fastening hardware into model assembly with 17 dark metal retaining clips in 3 sizes: 2 mm, 3 mm and 4 mm. Each E-ring is shaped to snap onto a matching groove on a shaft, axle, rod or pin, where it holds a mounted part in position while keeping the fixing compact and mechanical. The size spread makes the set useful across different fixing points instead of limiting the bench to a single diameter. In practical use, an E-ring is pressed onto the grooved end of a metal part so the open side clips over the shaft and the ring seats into place. That mechanism suits wheel mounts, axle retainers and other small moving assemblies where a screw or nut would take more space. The dark metal finish matches the function-focused character of workshop spares and replacement hardware. Kept in a parts box, drawer insert or service tray, the set supports routine maintenance as well as the recovery of lost clips during rebuilds. The stated scope of delivery is 1 set with 17 E-rings, giving a ready stock of common small retainers for model work that depends on secure, correctly sized mechanical fastening.  Warning! Not suitable for children under 14 years.

Gears & motor pinions

F Diff. Joint L & R, model spare parts for 58370

€20.99

F Diff. Joint L & R for 58370 supplies 2 dedicated spare parts for the front differential area, with one left and one right version matched to the named model reference. The black molded pieces show a technical, component-led form with flanged heads and split forked ends that suit connection points in a mechanical assembly. As model spare parts, these joints are intended for targeted maintenance rather than general upgrading. The paired L and R layout matters where the front drivetrain uses side-specific geometry, allowing the correct part to sit in the correct position instead of forcing a universal substitute. The visible shape of each piece supports that role: the cylindrical body forms the main connection section, while the forked end is made to interface with adjoining moving parts in the assembly. This keeps the focus on fit, alignment and restoring the original mechanical layout of 58370. On the workbench, the set suits planned servicing, replacement of worn front differential components, or completion of an existing build that needs the specified joints. The 2-part format keeps both sides of the front assembly covered in one pack, making it easier to match left and right positions during installation.  Warning! Not suitable for children under 14 years.

Gears & motor pinions

F101-F104 G-Parts Spur Gear Set, RC spare parts

€10.29

The F101-F104 G-Parts Spur Gear M0.6/63Z set is a drivetrain spare-parts pack for selected RC chassis, centered on a 63-tooth main gear with module 0.6 gearing. It gives a direct replacement route for wear parts in the transmission area and keeps compatible running gear ready for service sessions, rebuilds and routine maintenance. The set is specified for F104PRO II, F104W, F104 and F103GT chassis. For the F104PRO II chassis, the data states that only the 63T06 spur gear is used. Scope of delivery contains 1x G-Parts tree with 7 pieces, grouping the gear and related molded components in one pack for organized parts handling at the bench. The black molded parts shown in the set include the large spur gear and smaller matching pieces shaped for mounting and spacing within the assembly. This spare-parts set suits drivetrain refresh work after regular use, replacement during a rebuild, or keeping key transmission components on hand between running sessions. In a workshop setup, the defined chassis compatibility and exact 63-tooth specification make it easier to match the correct gear set before installation.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

F103 Turnbuckle Tie Rod Set, RC spare parts

€14.99

The F103 Turnbuckle Tie Rod Set brings adjustable linkage hardware to the F103GT chassis in a compact 20-piece spare parts pack. At the center are 2 turnbuckle shafts in 3 x 42 mm size, built to create a tunable connection within the steering or rod linkage layout. A reverse screw on 1 side of each shaft allows the rod length to be changed by turning the shaft itself, which helps when alignment needs fine correction during maintenance or reassembly. Alongside the shafts, the set provides 6 adjusters and 4 cushion balls in 5 mm size, plus the related small hardware for mounting and connection. This combination supports the pivoting and threaded joints used in RC chassis linkages, where clean fit and measured adjustment matter more than fixed-length parts. The included parts are suited to replacing worn linkage components or restoring a chassis with matching hardware dimensions already specified in the set. On the bench, the set fits naturally into steering service, linkage renewal or a parts refresh for an F103GT build. The compact format also makes it useful to keep with workshop spares, so the required rods, adjusters and joint hardware are ready when a setup change or replacement is needed.  Warning! Not suitable for children under 14 years.

Shock absorbers & springs

F103RS/GT-F104 Front Spring (3x4), model spare part

€5.59

The F103RS/GT-F104 Front Spring (3x4) is a model spare part for front suspension service on a wide range of compatible Tamiya chassis. With 12 coil springs in the pack, it supports routine replacement work as well as keeping matching spares ready for setup changes between running sessions. This set is specified for F103RS/GT-F104 applications and is listed for F104PRO II, F104Ver.II PRO, F104W, F104, F103GT, RM-01, TRF103, TRF102 and TRF101. That broad compatibility makes it useful for hobby benches that support more than one chassis generation. The 3x4 spring format gives a clear reference point when replacing existing front suspension parts, helping maintain the intended configuration on the car. As a dedicated spare part rather than a general hardware assortment, it keeps maintenance focused on the exact area that needs attention. On a workshop bench, the 12-piece quantity is practical for regular upkeep, rebuilds and storing reserve parts alongside a race or practice setup. It also suits builders who maintain several compatible chassis and want one spring pack that can stay in rotation across different models.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

F104 Disc Ball Set, chassis spare part, 3 mm

€5.69

The F104 Disc Ball Set is a dedicated spare part for ball differential maintenance on compatible F104 series chassis. With 8 steel balls and matching pressure plates in a 3 mm format, it supplies the key contact parts used in the differential assembly and keeps replacement focused on the stated drivetrain area. Compatibility is specified for F104PRO II chassis, F104W chassis, F104 chassis and F103GT chassis. The steel construction suits the repeated contact points inside a ball differential, where smooth, consistent interaction between the balls and plates is central to the mechanism. Instead of a broad assortment of unrelated workshop parts, this set stays specific to one service task and one family of chassis. The scope of delivery contains 1 balls and pressure plate set. On the workbench, that clear compatibility helps when preparing a planned refresh of an existing F104 drivetrain or keeping matching spare parts ready between running sessions. In a parts box for formula chassis maintenance, the 3 mm specification gives a direct reference for selecting the correct replacement set for the listed platforms.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

F104/F103 Special King Pin, model spare part

€4.49

The F104/F103 Special King Pin is a dedicated spare part for compatible F104 and F103 chassis, intended for maintenance, repair and ongoing setup work. As a king pin, it belongs to the front suspension area where precise alignment between steering and suspension components matters during rebuilds and replacement work. This part is supplied for the F104/F103 platform rather than as a generic hardware piece, which helps keep servicing focused on the correct chassis family. It suits replacing a worn or damaged king pin during routine maintenance, or keeping a matching spare ready in workshop storage for future repairs. The compact format also fits neatly into parts boxes and bench organisers used for model upkeep, making it easier to separate chassis-specific hardware from general screws and fittings. On the workbench, the part supports clean, direct replacement when a front-end rebuild is needed after running sessions or inspection. It also fits tuning and restoration tasks where the original suspension layout of an F104 or F103 chassis needs the correct replacement component rather than an improvised substitute.  Warning! Not suitable for children under 14 years.

RC spare parts

FF-03 Pinion Gear 28/29T, RC spare gear set

€16.29

The FF-03 Pinion Gear 28/29T M0.6 set adds a focused drivetrain tuning option for compatible RC chassis. Aluminum construction, a fluorine lubricating coating and a newly developed rounded tooth tip shape work together at the gear mesh to reduce friction losses and noise while supporting cleaner power delivery. The set provides 28T and 29T pinion options in module 0.6, making it useful when gearing needs to be adjusted for different running conditions or chassis setups. The rounded tooth profile changes how the teeth meet under load, which helps the drivetrain engage more smoothly as the motor turns through the spur gear. Compatibility covers a broad range of platforms including FF-04 EVO, FF-03, FF-03 PRO, TA08 PRO, TA07 MS, TA07 PRO, TA06 MS, TA06, TA06 PRO, TB-Evo.7, TB-Evo.6 MS, TB-Evo.6, TB-04, TC-01, TT-02RR, TT-02D, TT-02, XV-02PRO, XV-01 and XV-01 PRO. For TA07 MS chassis, use with 51356, 51423 and 51548. For TT-02, TT-02D and TT-02RR chassis, use with 54500. This gear set suits bench tuning before a run as well as drivetrain updates during regular maintenance. It also fits neatly into a spares box for racers and builders who keep multiple compatible chassis in rotation.  Warning! Not suitable for children under 14 years.

Gears & motor pinions

FF-03 Spur Gear 68T M0.6, RC spare part

€4.59

This spur gear brings a defined 68T tooth count and M0.6 pitch to compatible RC chassis, giving the drivetrain a concrete replacement part for service, repair and setup work. As a single main gear, it suits bench maintenance where a worn transmission component needs to be swapped for the correct specification. The part is listed for FF-03 chassis and FF-04 EVO chassis, and it also covers a broad compatibility range across TD4, TD2, TA06, TA06 MS, TA06 PRO, TA07 PRO, TA08 PRO, TT-02, TT-02 TYPE-S, TT-02 TYPE-SR, TT-02D, TT-02RR, XV-02PRO, XV-01, XV-01 PRO and XV-01T chassis. That spread makes it relevant for racers and builders managing several platforms within one workshop. On TT-02 based cars, use can also apply to vehicles equipped with 54500. For TT-02RR chassis, the gear is listed as kit standard equipment. In practical use, this is the kind of transmission part kept on hand for routine rebuilds, drivetrain refreshes and chassis-specific parts planning. The single-piece scope of delivery keeps the replacement straightforward when preparing a compatible touring, front-wheel-drive or rally platform for the next maintenance session.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

Flanged Tube, model accessory, 4.5 x 3.5 mm

€4.49

This flanged tube is a small model accessory specified at 4.5 x 3.5 mm and listed with detailed dimensions of 3.1 x 4.5 x 4.0 mm. The flanged form helps distinguish the part from a plain tube when a build or repair calls for a defined edge and a precise seated position within an assembly. The pack contains 2 matching pieces, which suits jobs that need a pair of identical fittings rather than mixed hardware. In model maintenance, exact measurements matter, and the stated 3.1 mm, 4.5 mm and 4.0 mm figures give a clear reference when checking parts against an existing setup. The compact format makes this accessory relevant for detailed replacement work, careful restoration, or keeping spare hardware ready for future servicing. On the workbench, a correctly sized flanged tube can save time during part selection because the specification is already narrowed to a defined format. For ongoing model upkeep, 2 identical tubes also make it easier to complete symmetrical mounting points or store a matched spare set alongside other small workshop parts.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

Flanged Tube, model accessory, 4.5 x 3.5 mm

€3.09

This flanged tube set is a small but specific model accessory for repair, maintenance and parts matching. The pack contains 2 pieces, and the stated 4.5 x 3.5 mm format gives a clear reference point when an existing assembly calls for the same size and flanged construction. The source data also lists the dimensional specification as 3.1(4.5) x 3.5(4.0) mm, which adds another concrete identifier for checking fit against a current build or replacement need. A flanged tube is typically chosen for its defined shoulder and seating position within a mechanism, so the named form matters as much as the measurement when selecting the correct hardware. In a workshop drawer, this kind of small component helps keep repair jobs moving without substituting an unmatched part. Used during model upkeep, rebuilds or careful parts sorting, the 2-piece set supports direct replacement where the same tube is needed again. It also works as a practical stock addition for builders who keep commonly used hardware sizes on hand for future service tasks.  Warning! Not suitable for children under 14 years.

Spare parts for old cars

Frog 2005 Wheel Adapter Set for Reissue Buggies

€18.29

This wheel adapter set is made for reissue buggy conversions where wheel choice matters. The hexagonal aluminium adapters allow The Frog 2005 and other specified chassis to use off-road tyres and wheels sold separately, changing the wheel mounting format for a wider range of buggy setups. The set contains 2 aluminium wheel adapters, 2 4 mm flange lock nuts and 2 stainless steel 2 x 10 mm shafts. Those parts form a compact hardware package for the wheel mounting area, with the shafts passing through the adapter and the lock nuts securing the assembly in place. The machined aluminium construction gives the adapters a clean, technical finish, while the stainless steel shafts add the matching metal hardware needed for the conversion. Compatibility is stated for chassis 58354 The Frog 2005, 58346 Hornet 2004, 58346 Grasshopper 2005, 57746 XB Grasshopper and 57741 XB Hornet. Used on a reissue buggy build, the set supports a switch to separately sold off-road wheel and tyre combinations that suit the chosen look or running surface. It also fits restoration work on older chassis where the original wheel format is being updated with compatible buggy wheels.  Warning! Not suitable for children under 14 years.

Spare parts for old cars

Front Upright Set F-103/Grasshopper II

€11.39

The Front Upright Set F-103/Grasshopper II is a chassis parts set for RC model maintenance, centered on the front steering area where precise fit matters most. With 21 pieces in the scope of delivery, the set provides the core hardware needed to replace worn front upright parts and restore the intended steering layout on supported Formula platforms. Compatibility covers F104PRO II, F104Ver.II PRO, F104W, F104 and TRF103, which makes this set useful across several established chassis generations. For TRF102 chassis and TRF101 chassis, the data specifies adjustment with 53585 shim, so the installation can be matched to those layouts as required. The included parts are intended for front-end assembly work rather than general chassis use, which keeps the application clear when servicing a car after running sessions or preparing a fresh build. On the bench, this set suits routine replacement of front upright components, careful steering rebuilds and targeted setup work around the axle carriers and related mounting points. It also fits the needs of hobbyists who keep multiple compatible Formula chassis in service and want the correct front suspension and steering parts ready for maintenance.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

Front Upright Set, model spare parts, MB10/11

€18.49

This front upright set supplies 2 matching metal parts for MB10/11, with left and right versions shaped as a mirrored pair for front-end replacement work. The silver finish and compact machined form give each piece a clean mechanical look, while the curved arm and pivot section point to a defined mounting role within the assembly. Each upright shows a circular attachment hole at one end and a rounded housing at the other, creating the connection points needed for a controlled mechanical fit. A vertical cylindrical shaft extends from each part and ends in a threaded screw tip, adding a fastening detail that supports installation into the intended front assembly position. One housing appears to carry internal threading, indicating that the two sides are not interchangeable and are made for their specific left or right placement. This set suits repair, maintenance or parts replacement on a compatible MB10/11 model where worn or missing front hardware needs a like-for-like component shape. Kept as workshop spares or fitted during a rebuild, the pair provides the dedicated geometry needed for accurate front-end restoration.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

Front Upright Set, RC spare part for Tamiya chassis

€6.19

This front upright set supplies 2 steering knuckles for the front axle of compatible RC chassis, giving the steering assembly the exact mirrored left and right parts needed for repair or routine maintenance. The shape with circular axle openings and multiple mounting points supports correct integration into the front suspension area, where precise alignment matters for wheel guidance and steering movement. The set is listed for a wide range of chassis platforms: FF-04 EVO, FF-03, FF-03 PRO, TA07 MS, TA07 PRO, TA06 MS, TA06, TA06 PRO, TA05 Ver. II, TB-Evo.6 MS, TB-Evo.6, TB-05 PRO, TB-04, TB-04 PRO, TB-03, TB-03 VDS and TT-02 TYPE-S. That broad compatibility makes this pair useful for keeping several touring car and front-wheel-drive builds in running condition with one clearly matched spare. The scope of delivery contains 2 front steering knuckles from C-Parts TB-03. In workshop use, this pair suits worn, damaged or missing front uprights on supported chassis and helps return the front end to its intended mounting layout. It also serves as a practical stock spare for regular service between driving sessions, especially on platforms that share steering and suspension hardware.  Warning! Not suitable for children under 14 years.

Gears & motor pinions

Gear Bag for 58340, model spare gear set

€7.19

This gear bag for 58340 brings the drivetrain back into service with 4 replacement parts shaped for geared power transfer. The set contains white injection-moulded components shown as 2 large gears, 1 smaller double pinion gear and 1 circular cover plate with 3 mounting holes, giving the gearbox area the core parts needed for a targeted repair. The larger gear with a raised cylindrical hub works alongside the second large toothed gear, while the smaller double pinion links motion between stages of the transmission. That layout points to reduction and transfer inside the gearbox rather than cosmetic trim, so the set is suited to maintenance where worn teeth, missing internals or damaged drive parts interrupt movement. The separate cover plate closes the assembly at the matching mounting points and helps return the parts to their intended position inside the housing. Used during a rebuild, service interval or parts replacement, this set supports focused work on the transmission section of 58340 without replacing unrelated assemblies. It also fits neatly into a spares collection for model maintenance, where keeping the correct gears on hand can shorten downtime between bench work and the next run.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

Gear Box Joint, replacement part for 43520

€8.99

The Gear Box Joint set for 43520 supplies 2 matching replacement parts for a drivetrain connection point where accurate fit matters. The machined metal finish and compact cylindrical form suit technical model maintenance, helping restore a clean mechanical link in the gearbox area when an original joint is worn, damaged or missing. Each joint is shaped as a dedicated spare for use with model number 43520 rather than as a generic workshop component. The 2-piece format provides a matched pair for repair planning and parts storage, which is useful when both sides of a mechanism need the same connection standard. The metal construction supports a precise seating surface at the contact point, which matters in assemblies where connected parts need to meet cleanly. As a small drivetrain component, this set fits naturally into regular service work on running models and mechanical rebuilds. On the workbench, the pair can be kept ready for scheduled maintenance or used to replace a failed connection during a repair session. For model builders who maintain existing vehicles over time, dedicated spare parts like these help keep compatible assemblies operating with the intended hardware.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

Gear Differential Putty, tuning accessory, 25 g

€8.29

Gear Differential Putty is a tuning accessory for transmission differentials in model vehicles, supplied as 25 g in a plastic case. By controlling the differential action, it creates an effect close to direct coupling, changing how the drivetrain responds when load builds through the driven wheels. The putty is applied as a physical insert rather than a mechanical replacement part. The rolled material is cut with scissors, formed to about 3 mm in diameter, and then packed into the transmission differential. This gives a clear, hands-on way to adjust internal resistance with small portions instead of replacing the whole differential assembly. The method suits fine setup changes, because the amount and shape of the putty can be prepared before installation. The supplied case keeps the material contained between workshop sessions. Under heavy load from the road surface, the transmission moves to help avoid damage to the drive system, so the tuning effect is paired with protective drivetrain behavior. This makes the putty useful for setup work on model vehicles where differential response has a direct influence on handling and power delivery during running sessions.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

Gearbox B Parts, RC spare parts for M.Pumkin

€19.29

This B Parts gearbox set is made for M.Pumkin and Lunch Box and provides the molded components needed for work on the transmission housing area. The black sprue carries matched structural pieces that suit replacement, restoration, or a fresh rebuild when worn or damaged gearbox sections need to be exchanged. The visible layout shows 2 mirrored casing halves, a central round cover piece, and 2 smaller circular discs, all molded as a coordinated parts tree. That arrangement helps keep related components together before removal and gives a clear overview of the shapes used in the assembly. The larger shells feature cylindrical tower forms and ribbed circular housing details, indicating their role as enclosing and supporting mechanical internals. Because this is a model spare-parts set, it is intended for an existing compatible vehicle rather than as a standalone build. On the bench, this set supports focused repair work on the gearbox section of the compatible RC model. It also suits keeping a replacement sprue on hand for maintenance, especially where a rebuild calls for matching housing geometry instead of improvised substitutes.

Shock absorbers & springs

GF-01 Alu. Oil Damper (4), RC damper set

€62.49

The GF-01 Alu. Oil Damper set adds 4 aluminum oil dampers to GF-01 and WR-02 chassis cars, bringing more controlled suspension movement to rough ground and uneven running surfaces. Silver-finish cylinders with blue anodized caps and ends give the chassis a crisp mechanical look while introducing a functional oil-filled damping setup. The set is supplied as an aluminum oil pressure shock absorber set with 99 pieces, including the small attachment parts needed for mounting. The assembly documents show 3-hole pistons, damper shafts, rod guides, O-rings, spacers and ball connectors working together inside each cylinder to manage suspension travel. Front and rear damper builds differ by chassis position, with 2 dampers configured for the front and 2 for the rear. The included damper oil is specified as #400 in the assembly notes. Use with spring kit 53974 is stated in the data, and G6-01 or G6-01TR chassis require 6 dampers where that setup is used. Installed on a GF-01 or WR-02 model, the dampers support more composed running when the chassis crosses loose ground, bumps and broken surfaces. The color-contrasting hardware also stands out during workshop assembly and suspension tuning, where each cylinder, cap and end remains easy to identify at a glance.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

GF-01 Full Ball Bearing Set, chassis accessory

€39.99

The GF-01 Full Ball Bearing Set is a chassis accessory made to give GF-01 models a complete bearing upgrade with the exact quantities needed in one pack. The set contains 24 x 1150 ball bearings and 2 x 850 ball bearings, replacing the standard bearing arrangement at the rotating points across the chassis. By swapping in ball bearings for the kit standard plastic and metal bearings, the running gear can turn with less drag and a more consistent mechanical feel. The different bearing sizes cover the positions required by the GF-01 layout, so the set is built around the chassis rather than a generic assortment of parts. The compact metal components suit maintenance work, rebuilds and planned performance upgrades where efficient rotation matters. On the bench, the set supports a straightforward refresh of a used GF-01 runner or a more refined specification for a fresh chassis build. Once fitted, the smoother movement through the rotating assemblies helps the model make cleaner use of its available power during regular driving sessions.

Spare parts for old cars

Grasshopper Hornet chassis, RC spare part, black

€12.69

This black chassis part for Grasshopper and Hornet models restores the central structure that carries the main assemblies of the vehicle. The moulded tub-style form combines side walls, mounting posts, screw holes and slots in one component, creating the defined base needed when a worn or damaged frame has to be replaced. Raised supports and cross braces are built into the moulding, so matching parts can be positioned against the chassis geometry already formed into the piece. The front and rear sections show reinforced mounting areas with several connection points for attaching the surrounding assemblies. That layout matters during repair work because the chassis is the reference part that determines how the rest of the model sits and aligns. The black finish matches the part designation, while the one-piece construction keeps the replacement focused on the core frame rather than a collection of separate brackets. Used in a restoration, rebuild or maintenance project, this spare chassis gives Grasshopper and Hornet models the correct base for reassembly. It suits workshop tasks where the original frame has cracked, worn at the mounting points or needs to be exchanged during a longer-running RC model refresh.

Gears & motor pinions

Hard Joint Cup-Set Gear Differential Spare Part

€14.99

This spare part set combines a differential output with a hardened cone differential for gear differential service on compatible model vehicles. The pairing suits focused drivetrain maintenance where the differential assembly needs renewal with the two named components supplied together. The hardened cone differential is the key technical element in the set, adding a wear-oriented replacement part for rebuilds and repair work. In a gear differential, this component supports the transfer of drive through the transmission while the differential output forms the matching connection point within the assembly. The scope of delivery is clearly defined as 1 differential output and 1 hardened cone differential, which helps when planning a direct replacement around the existing drivetrain layout. The set is intended as an accessory and replacement component rather than a complete model. On the workbench, this combination fits routine servicing, repair after drivetrain wear, or preparation of a compatible chassis for further running. It also suits parts storage for model maintenance, where a clearly specified differential set can be kept ready for the next rebuild.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

Hi-Torque Servo Saver Black, RC spare part

€17.99

Hi-Torque Servo Saver Black brings a focused steering upgrade or replacement part to RC chassis work, with a 26-piece set that combines black molded components and metal hardware in one servo saver assembly. Built for the MF-01X chassis, it gives the steering system the dedicated parts needed where controlled force transfer and linkage connection matter during running and maintenance. The set contains the servo saver itself together with screws, nuts, washers, retaining rings and threaded ball studs. Those ball studs create the mounting points for linked steering rods, while the retaining rings secure the relevant rotating or stacked parts within the assembly. Combined use with 54120 is specified in the data, which matters when matching the setup to the intended chassis configuration. The black finish keeps the installed assembly visually consistent with surrounding chassis parts, and the grouped hardware avoids piecing together separate fasteners for this specific mechanism. On the bench, this spare part suits routine servicing, parts replacement or a fresh chassis build centered on the MF-01X platform. It fits naturally into steering work where worn saver parts, missing hardware or a chassis-specific installation calls for the correct component set rather than a generic substitute.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

Hi-Torque Servo Saver, 1:10 accessory, white

€17.29

The Hi-Torque Servo Saver in white is a steering accessory for RC model setups that need a precise, compatible linkage part. Designed for all Tamiya chassis and many 1:10 models, it supports cleaner steering response while improving return after direction changes, making it useful for fresh builds, maintenance work and replacement installs. The set combines white molded components with the small hardware needed to mount and connect the assembly, including screws, nuts, washers, retaining rings and ball-ended linkage parts. Those ball-joint style connectors support the steering linkage where controlled movement and secure attachment matter, while the retaining rings and fasteners complete the mechanical fit. For MF-01X chassis, combined use with 54120 is specified, which helps align the part choice with that chassis configuration. On a workshop bench, this servo saver suits routine servicing as well as targeted steering updates on compatible 1:10 RC cars. It also works as a useful spare for keeping an existing chassis ready when worn steering parts need to be replaced with matching hardware and mounting pieces.  Warning! Not suitable for children under 14 years.

Spare parts for old cars

Hornet Clamp Aluminum Wheel Hubs 2-Piece Set

€28.29

This 2-piece set of clamp-type aluminum wheel hubs is designed as a focused upgrade for classic Tamiya off-road models, replacing the kit-standard B5 parts with a more rigid wheel connection. Each hub clamps onto the wheel axle instead of relying on a simpler fit, which helps keep wheel attachment precise and supports smoother rotation while the model is running. The set includes 2 aluminum wheel hubs and screws for attachment, keeping the mounting hardware aligned with the upgrade itself. A blue anodized finish gives the hubs a clear visual contrast at the wheel area, adding a technical accent that stands out during assembly and once the model is on display. The clamp construction is the key mechanical difference here: tightening the hub onto the axle creates a firmer interface between axle and wheel, which is especially useful where accurate wheel seating matters. Compatibility is stated for the Hornet, Frog, Lunch Box, Monster Beetle, Grasshopper, Subaru Brat and Fast Attack Vehicle. That makes the set a practical choice for restoring, refining or visually updating several well-known chassis in one parts family. On a bench build or a running model, the hubs bring together precise attachment, aluminum construction and a distinctive blue finish in one compact upgrade.  Warning! Not suitable for children under 14 years.

Shock absorbers & springs

J Parts Fr. Damper Stay, model spare parts set

€14.79

J Parts Fr. Damper Stay is a dedicated spare parts set for the 58618 Mt.Beetle and focuses on the front damper mounting section used in the chassis structure. The molded black components are supplied on a sprue frame, giving a clear overview of the shapes before cutting, test fitting and installation during a repair session. The set is suited to replacing worn, damaged or missing structural parts rather than improvising with unmatched hardware. Multiple mounting pieces and braces are formed as matching components, which helps maintain the intended geometry around the front suspension area. The sprue layout also helps with part identification at the bench, especially when several maintenance jobs are underway at once. Because this is a model spare parts set rather than a complete vehicle or kit, it fits naturally into regular workshop use alongside stored service parts for ongoing upkeep. On the work surface, the parts support a focused rebuild of the front end after heavy running or accidental damage. They also make sense as reserve stock for a 58618 Mt.Beetle build that is driven regularly and maintained over time, where having the correct front damper stay parts ready can shorten downtime between sessions.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

J-Parts for Subaru Impreza WRC'08, model parts

€14.19

This J-Parts set is made for the Subaru Impreza WRC'08 from kit 58426 and serves as a dedicated replacement parts option for that exact model. The defined J-Parts designation helps identify the correct section within the original build, which is useful when an existing model needs a missing or worn component replaced rather than improvised with a non-matching part. Because the data names this set specifically for 58426, the fit reference is tied to that kit and to the Subaru Impreza WRC'08 body version listed here. That makes the set relevant for repair work, restoration of an older build, or keeping a previously assembled model in running or display condition with the intended parts group. As model supplies, these parts are aimed at maintaining an existing build rather than changing it into a different version. On the workbench, a dedicated replacement set like this can save time when sorting spares for a rebuild or when completing a model that is missing one defined parts section. It also gives collectors and builders a clear way to keep kit 58426 aligned with its original specification over repeated maintenance cycles.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

Joint Boot BB21, spare part for Mt.Beetle

€4.39

Joint Boot BB21 is a model spare part specified for the Tamiya 58618 Mt.Beetle. The long black component has a bellows-style form with several ribbed sections and thicker collar points, a shape used where a fitted cover needs to move with the linked assembly while keeping the area around the joint enclosed. The moulded one-piece construction gives the part a clean technical profile for maintenance, replacement or a faithful rebuild of the original model layout. Its accordion-like sections indicate controlled flexibility, allowing compression and extension as the connected mechanism moves. The stepped ends and central collars provide defined seating points that match the intended mounting position rather than acting as a generic sleeve. That makes BB21 useful when an existing boot is worn, split or missing and the assembly needs the correct designated part again. In workshop use, this spare part fits naturally into repair sessions focused on keeping a Mt.Beetle complete and mechanically tidy. It also suits stock-box planning for regular running models, where model-specific service parts help keep maintenance work straightforward and consistent with the original specification.  Warning! Not suitable for children under 14 years.

Shock absorbers & springs

Leaf Spring A (4), model spare part for 58372

€14.49

Leaf Spring A is a dedicated model spare part set for 58372, supplied as 4 matching spring strips in black metal. Each strip has a curved profile, rolled looped ends and 3 round mounting holes near the centre, giving the set the exact component form needed where this part group is missing, worn or due for replacement. The 4-piece pack supports maintenance and rebuild work with a consistent set of identical parts rather than mixed hardware. The metal strips are shaped for suspension-style or retaining-style installation within the matching model assembly, and the repeated hole pattern helps align the part with the existing mounting points on 58372. This makes the set useful for restoring the original mechanical layout of the designated model instead of adapting a generic strip or bracket. The compact spare part format also suits keeping a correct replacement set on hand for workshop storage. On the bench, the set fits naturally into repair sessions, part swaps and planned overhauls of 58372. It also works as a direct stock replacement when a rebuild calls for the exact Leaf Spring A component rather than an improvised alternative.

Shock absorbers & springs

Leaf Spring B, spare part set for 58372

€8.29

Leaf Spring B is a dedicated spare part set for 58372 and supplies 4 matching replacement pieces for repair or maintenance work on the designated model. The set uses one clearly defined component type, making it suitable when the original leaf spring elements need to be exchanged rather than replacing a larger assembly. Each piece follows the same curved form shown in the reference image, with 3 round mounting holes positioned near the centre for attachment. That repeated geometry matters during maintenance because all 4 parts share the same layout and can be fitted as matching replacements within the same suspension area. The black finish keeps the appearance consistent with the pictured parts, while the compact format suits parts storage in a workshop drawer, spares box or model case between repair sessions. As a model spare part, this set is aimed at restoring the intended structure of 58372 with the correct designated component rather than adapting a generic substitute. The 4-piece format supports planned servicing as well as single-part replacement when a matching spare is needed on hand. On the bench, the identical hole pattern and arched profile help keep repair work focused on the exact section that needs attention on 58372.  Warning! Not suitable for children under 14 years.

Shock absorbers & springs

Leaf Spring, spare part set, 2-piece suspension pair

€5.99

This leaf spring set supplies 2 replacement suspension parts for compatible model maintenance and repair work. Each piece is formed as a curved metal spring strip, creating the arched profile needed for a leaf spring layout and giving a clear mechanical role within the assembly. At the center of each spring, 3 round mounting holes provide the fastening area for installation to the matching structure. The ends are bent into looped hooks in opposite orientations, showing that the parts are made as a left and right mirrored pair rather than 2 identical strips. That mirrored construction matters when restoring the original suspension geometry on both sides of a vehicle. The black finish and compact shape also make the parts easy to identify among workshop spares during servicing. The set suits rebuilds, repairs, and parts replacement on a compatible model that uses this spring format. Whether a suspension assembly is being refreshed after wear or a stored build is being returned to running condition, these 2 springs provide the specific hardware needed for the job.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

LED Stopper, model accessory, 2 pcs.

€5.99

This LED Stopper set is a focused model accessory for detailed assembly work, supplied as 2 sprues with multiple molded stopper pieces ready to be removed and fitted as needed. The compact format keeps matching parts together on the runner, which helps maintain order while preparing small components at the bench. Each sprue is injection molded in ABS and marked with part identifiers, giving the set a clear technical character that suits precise hobby tasks. The forked stopper shapes shown on the runners support controlled placement in builds that call for small retaining parts. Because the pieces stay attached until needed, sorting and handling remain straightforward during preparation. The uniform molded layout also helps when checking parts before cutting them free. On the workbench, this set fits naturally into careful model sessions where small components and clean organization matter. It suits builders who want a dedicated supply of matching stopper pieces on hand for compatible projects and detail-focused assembly steps.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

Left Upright Front, RC spare part with ball stud

€6.99

This front left upright is a dedicated spare part for the Stadium Blitzer and is intended to restore a specific suspension or steering connection point in the front corner assembly. The molded piece combines a compact arm shape with a central round mounting hole, creating the defined pivot location needed for the surrounding mechanism to sit correctly. A brass-colored ball stud at one end adds the articulated connection point for the linked assembly. The upright also carries a silver metal shaft with a threaded tip, which provides the fastening point for installation into the matching front section. Reinforced ribs in the molded body support the shape of the part around the mounting area, while the white finish makes the component easy to identify during maintenance or parts sorting. Supplied as 1 piece, it is specified as the front left version rather than a universal side-to-side replacement. This kind of spare part suits focused repairs after wear, damage or a missing original component in the Stadium Blitzer. Kept in a workshop drawer or parts box, it supports routine maintenance and helps return the front assembly to its intended mechanical layout with the correct left-side geometry.  Warning! Not suitable for children under 14 years.

Shock absorbers & springs

Low Friction Damper V Parts, RC spare parts

€7.29

Low Friction Damper V Parts supply the small running components that keep RC damper assemblies working smoothly across a wide range of Tamiya chassis. The set contains 2 V-part sprues with 22 pieces and covers damper ends, top ends, spring retainers, resin pistons and resin damper spacers for low-friction, ultra-low-friction and TRF dampers. This spare parts set is aimed at rebuild work, scheduled maintenance and replacing worn suspension internals without changing the full damper assembly. The dark gray molded parts arrive on sprues for clean identification during bench work. Compatibility reaches across touring, formula, buggy and rally platforms named in the data, including XV-01, TA06, FF-03, TT-02, M-07 CONCEPT, M-08 CONCEPT, F104, DB01 and TD4 chassis. Several applications require combination with matching damper sets such as 53571, 42273, 42355, 42102, 42354, 53901, 53926 or 54993 as specified in the data. On a workshop bench, these components help restore precise damper movement after wear in the original running parts. They also make a practical stock addition for regular chassis servicing, especially where multiple compatible Tamiya platforms are already in use.  Warning! Not suitable for children under 14 years.

Shock absorbers & springs

Lunch Box D-Parts, replacement parts set

€16.99

The Lunch Box D-Parts set is a dedicated replacement parts pack for 58063, supplying molded components on sprues for repair, restoration, or planned maintenance. Black injection-molded pieces with formed mounting shapes and structural contours support accurate replacement work while keeping the original model configuration intact. The sprue layout keeps the individual parts grouped until they are cut free, which helps with part identification during bench work and reduces mix-ups between similar small components. Visible shapes in the set include bracket-style sections, circular adapter-like pieces, connector forms, and a larger reinforced panel with raised ribbing. That mix points to structural and mounting functions rather than decorative trim, making the set useful when worn, broken, or missing components need to be exchanged with matching replacements. The molded finish and defined edges also support clean alignment during fitting. On the workbench, this set suits rebuilds after heavy running, careful restoration of an older Lunch Box, or keeping spare components ready for future service. It also fits organized parts storage for hobby rooms where model-specific replacement sets help keep maintenance straightforward.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

LW X-Joint for W Cardan, model spare part

€5.69

The LW X-Joint for W Cardan is a dedicated spare part set for compatible model driveline assemblies. With 4 replacement pieces in the pack, it supports routine maintenance where worn joint parts can affect the movement of a W Cardan setup during running sessions. Used in the correct compatible assembly, each X-joint serves as a small but important connection point within the driveline. Replacing these parts can help restore the intended fit and motion of the mechanism without changing the overall layout of the model. The set is suited to workshop stock, scheduled service work, or repair after wear on an existing compatible setup. Its focused format keeps the purchase tied to one concrete task: renewing the X-joint section of a W Cardan assembly with matching spare parts. On the bench, the 4-piece pack is practical for keeping replacement parts ready before a maintenance session starts. It also suits hobby storage where frequently used driveline spares are kept together for compatible model repairs and ongoing upkeep.  Warning! Not suitable for children under 14 years.

Screws & ball head screws

M 4 x 11,5mm Step Screw/King Pin, RC spare part

€2.19

This spare-parts set supplies 5 M 4 x 11,5 mm step screws/king pins for selected R/C machines, with a stepped metal form that combines a smooth shoulder section and a threaded end. That layout suits fastening points where parts need both guided location and secure fixing, making the set useful for routine maintenance, worn-part replacement or keeping matching hardware on hand for workshop stock. Each screw uses a slotted dome head, giving a clear contact point for fitting and removal with the appropriate tool. The 11,5 mm length and M4 format identify the hardware precisely, which helps when replacing like for like instead of mixing different screw types in one assembly. As a king pin or step screw, this part is intended for positions where the shoulder section matters as much as the thread, rather than acting as a standard fully threaded fastener. The set is listed as compatible with selected R/C machines including Fiat 500, Team Repsol Mitsubishi Ralliart Racing LANCER, Baja King, DualHunter and Plasma Edge. It fits naturally into repair sessions, rebuilds after heavy running, or parts sorting in a model workshop where exact hardware size matters.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

M-03 Assembly Universal Shaft, RC spare part set

€51.99

The M-03 Assembly Universal Shaft set brings a serviceable drivetrain upgrade to compatible Tamiya chassis with 2 cardan shafts supplied as 15-piece assemblies. Each shaft is built to be assembled and disassembled, giving direct access to the joint parts during installation, cleaning or routine running maintenance. This set is specified for the M-03 chassis and also fits M-05, M-05 PRO, M-05 ver.II PRO, M-06, M-06 PRO and MF-01X chassis. The interchangeable references 53499, 53500, 53681 and 54410 make it easier to match an existing parts list when refreshing a drivetrain or replacing earlier shaft sets. For MF-01X chassis, the data notes combined use with 54000. The included layout shown for the set covers the shaft components, small hardware and assembly tool needed for the 2 shaft builds. In workshop use, the take-apart construction supports regular inspection of the moving joint sections after repeated running sessions. During a rebuild of an M-chassis touring car, the set gives a clear route to replacing worn drivetrain parts while keeping compatibility across several related platforms.  Warning! Not suitable for children under 14 years.

Gears & motor pinions

M-05 Ball Bearing Set, chassis accessory, 18 pcs

€41.49

The M-05 Ball Bearing Set is a chassis accessory made for M-05 machines and brings the full bearing count needed for a focused running gear update into one pack. With 18 metal ball bearings in 2 specified sizes, it supports smoother mechanical movement at the points where rotating parts meet, helping the chassis run with less drag during regular use. The set contains 6 x 850 ball bearings and 12 x 1150 ball bearings, matching the size combination stated for M-05 chassis compatibility. That size split makes the set useful for planned maintenance as well as for replacing worn bearings during a rebuild. In an RC chassis, ball bearings sit at key rotating points and reduce friction compared with basic bushings, which can help the drivetrain turn more freely and keep the response of the running gear more consistent. The silver-coloured metal finish reflects the precision-part character of the set and fits the technical look of workshop spares and tuning parts. On the bench, this bearing set suits routine chassis servicing, parts replacement after extended running, or preparation for a cleaner rolling setup before the next session. It also works as a practical stock part for M-05 owners who prefer to keep the specified 850 and 1150 bearing sizes ready for future maintenance.

Axes & drive shafts

M-05 C-Parts, suspension spare parts set

€17.49

The M-05 C-Parts suspension spare parts set supplies the designated C section for several compact Tamiya chassis, making it a practical choice when suspension-related components need replacement during maintenance or repair. With 46 pieces on 1 parts tree, the set groups matching molded sections together for rebuild work on compatible RC car platforms. Compatibility covers M-06, M-06 PRO, M-05 ver.Ⅱ PRO, M-05, M-05 PRO and MF-01X chassis. That broad fit makes this set useful for workshops, spare parts storage and ongoing running repairs across more than one chassis type. The molded parts format also helps identify and separate the required sections before installation, which keeps rebuild work organized when replacing worn or damaged areas. Scope of delivery: 1x C parts, 46 pieces. This spare parts set suits routine servicing after track use, collision damage or part loss during disassembly. It also fits planned refresh work on an existing chassis, where keeping the correct designated section on hand can shorten downtime between maintenance sessions.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

M-05 F-Teile, spare parts set, wheel hub

€9.39

The M-05 F-Teile set is a dedicated spare parts pack for compatible Tamiya chassis, supplying 12 replacement components for maintenance on running gear assemblies. The set is intended for M-06, M-06 PRO, M-05 ver.II PRO, M-05 and M-05 PRO chassis, making it a practical match when original parts need replacement after regular use. The included F parts are shown as black moulded resin components with multiple mounting holes, pivot points and axle or bearing openings shaped for their specific positions in the assembly. Left and right mirrored forms support correct placement during rebuilds, while the mix of upright, hub and small insert style pieces helps address wear in connected front-end areas. This kind of chassis-specific parts pack is useful when keeping an existing RC car in running condition rather than replacing a full assembly. On the bench, the set suits routine servicing, repair after contact damage, or preparation of a second chassis for use with the same platform family. It also helps maintain parts support across several related M chassis versions, which is useful for hobby setups that rotate between M-05 and M-06 based builds.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

M-05 Ver.II A Parts, chassis spare parts set

€18.79

The M-05 Ver.II A Parts chassis set is a focused upgrade and replacement option for the M-05 platform, bringing Ver.II chassis geometry to existing builds while also restoring worn sections on the M-05 Ver.II PRO. Black molded chassis components form the core of the set, with the layout shaped around updated battery and servo fitment options. Within the chassis, parts A8 and A9 allow installation of square-shaped battery packs in place of earlier chassis pieces, and the instruction data notes that the battery pack is secured with glass tape. A redesigned A3 section opens space for a low-profile servo during assembly, while standard-size servo installation uses part A7 with 3 x 18 mm tapping screws. The motor position shifts 3 mm closer to the center, changing the weight distribution within the chassis. The set is also compatible with Item 54606 one-piece lower suspension arms, which allows rebound stroke adjustment when that arm set is used. Some bodies may require trimming where they interfere with the chassis. This chassis parts set suits maintenance, repair and specification updates on compatible M-05 variants. It fits naturally into workshop sessions that focus on replacing broken sections, adapting battery layout, or revising servo placement on an existing front-wheel-drive touring car build.

Axes & drive shafts

M-05Ra F-Parts, RC chassis parts set

€9.99

The M-05Ra F-Parts set is a dedicated RC chassis parts set for the M-05 RA chassis, centered on the upright front and rear area. With 21 pieces in 1 F-parts frame, it provides the specific molded shapes needed when a suspension or steering section has to be rebuilt with matching left and right components. The set contains black molded parts with multiple mounting holes, cylindrical pivot sections and forked connection points. These details matter during assembly because they define how links, axles and adjacent hardware sit in the chassis. The layout shown for the parts also includes small spacers, washers and connector plates, which support alignment and spacing in the assembled upright section. Rather than replacing unrelated sections, this set addresses one clearly defined area of the M-05 RA platform. That focused fitment suits maintenance after heavy running, accident damage or a full chassis refresh. It also helps when keeping a build consistent with the original M-05 RA configuration, using parts intended for that exact platform. The scope of delivery contains 1x F parts set with 21 pieces.  Warning! Not suitable for children under 14 years.

Gears & motor pinions

M-07 Concept Spur/Counter Gear RC Spare Set

€4.59

The M-07 Concept Spur/Counter Gear set is a model-specific transmission spare for M-07 Concept chassis cars, supplying the 2 molded gearbox gears needed for a full internal replacement. The set contains 1 main spur gear and 1 counter gear, each formed as a compound gear so the paired tooth counts work together inside the gearbox. The spur gear is specified as 37T/21T and the counter gear as 29T/23T. Those tooth combinations are the key mechanical detail of the set, because they determine how the gears mesh across the transmission stages in the M-07 Concept gearbox. As replacement parts, these gears are intended to renew the internal drive path where wear or damage affects smooth running. The studio image shows white molded gears with fine, evenly spaced teeth, hollow center openings and integrated stepped sections shaped for their gearbox positions. This set suits routine drivetrain maintenance on an M-07 Concept chassis car or a targeted gearbox rebuild after heavy use. Kept in a pit box, workshop drawer or spares case, the matched pair gives a direct way to restore the complete gearbox with the specified gear combination for this chassis platform.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

M-08/M-07 Concept A Parts, chassis spare set

€14.29

The M-08/M-07 Concept A Parts set is a dedicated spare tree for keeping compatible chassis cars ready for service. Designed for the M-08 CONCEPT chassis and M-07 CONCEPT chassis, it supplies the A parts needed when original mounting components are damaged, worn or missing after regular RC use. The set contains 1x A parts tree with 24 pieces and provides spares to replace parts on 1 chassis. Its focus is the body mounting area: body mounts and body mount stiffeners restore the connection points that support the shell on the chassis. That makes this set useful when a shell no longer sits correctly, when mounting points have been stressed during running, or when a rebuild calls for fresh hardware from the original parts group. As a model-specific spare set, it stays close to the intended chassis layout instead of relying on mixed universal hardware. The parts suit workshop stock, routine maintenance and targeted repairs on compatible M chassis builds. During a rebuild, the tree format helps keep related components together while damaged pieces are exchanged. For regular RC maintenance, this spare set covers a focused section of the chassis with the exact A parts group named for the M-08 CONCEPT and M-07 CONCEPT platforms.  Warning! Not suitable for children under 14 years.

Gears & motor pinions

M-08/M-07/TA06 Gear Diff. Gasket (2), spare part

€2.69

This spare part set provides gear differential gaskets for compatible Tamiya chassis and supports clean, precise maintenance of the cone differential area. The pack contains 4 flat gaskets, each formed as a circular seal with a shaped center opening, 4 inward tabs and 4 outer holes for the matching mounting pattern. Compatibility covers M-08 CONCEPT, M-07 CONCEPT, TA06, TA06 PRO, TA06 MS, TA05 Ver.II, TD2, TD4, DB01, FF-04 EVO, TRF503, TRF211XM, TRF201XMW, XV-01, XV-01 PRO and XV-01T chassis. For specific setups, TA05 Ver.II uses the gasket with 54312, DB01 uses it with 54329, and TD4 and TD2 use it with 54471. The thin gasket format suits replacement during differential service when worn or compressed seals need to be exchanged for matching new parts. In workshop use, the 4-piece pack supports repeated maintenance sessions or more than one compatible chassis in the collection. The clearly defined cut shape helps align the gasket with the cone differential section during installation, keeping service work focused on fit and correct parts matching.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

Manta Ray A-Parts Gearbox Spare Parts Set

€15.49

The Manta Ray A-Parts gearbox set supplies replacement molded components for the 58087 model, centering on the transmission and nearby chassis-mounted assemblies. The black parts come on a single sprue, making each section easy to identify before cutting and positioning during repair or rebuild work. Visible pieces include a large gearbox housing with multiple screw holes, a separate cover or mounting plate, a cylindrical housing element, several hexagonal hub-like parts, and a wider support bracket. This mix supports work in the drivetrain area where aligned mounting points and matching shapes matter. Because the parts are molded as a coordinated set, the geometry across the housing and support sections stays consistent with the intended assembly. The sprue format also helps keep smaller pieces together until they are needed at the bench. This spare parts set suits restoration of a used chassis, replacement of worn transmission-area pieces, or preparation of a stored Manta Ray 58087 for running condition again. It also fits organized workshop stock where model-specific service parts are kept ready for future maintenance.

Gears & motor pinions

MB-01 29T Pinion Module 0.6, RC pinion gear

€5.39

The MB-01 29T Pinion Module 0.6 is a drivetrain spare part made for the Tamiya MB-01 chassis. With 29 teeth and module 0.6 gearing, it gives the transmission a clearly specified replacement component for maintenance work, rebuilds and planned parts stocking around an existing MB-01 setup. The compact gear uses a toothed outer profile and a central mounting hole to sit in the drive system as intended for this chassis platform. The engraved 29 marking provides a quick visual check during bench work, which helps when matching the installed ratio to workshop notes or separating parts between different builds. As a single-piece replacement, it suits targeted servicing where one worn pinion needs to be exchanged rather than a full drivetrain refresh. The metal construction also makes it a natural fit for a mechanical assembly that depends on accurate tooth engagement. In workshop use, this pinion gear supports routine transmission maintenance, parts sorting and chassis-specific repairs. It also works well as a spare kept alongside other MB-01 running gear, ready for rebuild sessions or for replacing a used gear after repeated track time.  Warning! Not suitable for children under 14 years.

Shock absorbers & springs

MB-01 A-Parts Uprights, chassis parts set

€7.19

This MB-01 A-Parts set brings several core chassis pieces together for focused maintenance on the MB-01 platform. The pack contains uprights, a gear cover, suspension mounts, a damper stay and hex hubs, giving rebuilds and repairs the matching parts needed for the correct locations within the chassis layout. The different components cover multiple mechanical jobs across the car. Uprights sit at the wheel ends and provide the mounting points around the axle area, while the hex hubs connect the wheel fitment to the drivetrain side. The gear cover closes off part of the transmission area, and the suspension mounts and damper stay support the placement of suspension and damping hardware on the chassis. Because these parts are supplied as A-Parts for the MB-01 chassis, the set suits replacement of worn pieces, accident damage or missing original components without mixing unrelated hardware. On the bench, this set supports anything from a single damaged corner repair to a broader chassis overhaul. It also works well as workshop stock for MB-01 owners who want the correct molded parts ready for routine service, rebuild planning or trackside maintenance between running sessions.

Axes & drive shafts

MB-01 C-Parts Transmission Spare Parts Set

€7.19

The MB-01 C-Parts Transmission set supplies replacement drivetrain parts for the MB-01 chassis, centering on the transmission area where matched fit matters most. Black molded components and metal shaft sections form a compact service set for restoring the original mechanical layout with the specified C-parts. Included are differential cup joints, axle shafts, dogbone shafts and propeller shafts, grouped for transmission-related maintenance on the MB-01 platform. The forked cup pieces and connecting shafts handle the mechanical link between rotating drivetrain sections, while the smaller spacers and retaining hardware shown in the set support correct assembly of the replacement parts. This makes the set useful when worn or damaged transmission components need to be exchanged with the designated matching parts rather than improvised substitutes. On the workbench, the set supports targeted repair of an MB-01 drivetrain without changing to a different chassis standard. It suits routine maintenance, rebuilds after heavy running, or keeping spare transmission components ready for the next service interval on an MB-01 model.

Gears & motor pinions

MB-01 D-Parts Gearbox, chassis spare parts

€9.49

The MB-01 D-Parts Gearbox brings together key chassis components for repair, maintenance and parts replacement on the MB-01 platform. This sprue covers several of the mechanical sections that shape the layout of the chassis, with moulded parts for the drivetrain area, deck structure and steering system arranged as one matched set. Alongside the motor mount, gearbox and upper deck, the set also provides an R/C equipment deck and wheelbase adjustment parts for the MB-01 chassis. The black moulded pieces show reinforced ribbing, axle openings, hinge points and screw locations that suit structural mounting and gearbox housing tasks within the chassis build. Because these parts are supplied together on the D-Parts sprue, matching sections can be replaced with the correct group intended for the same platform. This set suits workshop use when an MB-01 chassis needs worn or damaged sections exchanged, or when a stored build is being returned to running condition with the proper chassis hardware. It also fits ongoing bench maintenance where drivetrain housings, steering mounts or deck sections need the original replacement parts for the model.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

MB-01 Full Ball Bearing Set, chassis accessory

€26.29

The MB-01 Full Ball Bearing Set equips the MB-01 chassis with a complete 18-piece bearing package sized for its rotating assemblies. With 12x 1050 bearings, 2x 1280 bearings and 4x 850 bearings, the set brings together the exact mix needed for a full conversion in one chassis-focused pack. Ball bearings are used at points where shafts and axles rotate, replacing plain bushings with rolling elements that reduce friction during operation. In an RC chassis, that lower drag can support freer drivetrain movement and a more direct mechanical feel across the running gear. The different bearing sizes in this set are arranged to match the MB-01 layout, so the contents are not a generic assortment but a model-specific combination for this platform. The compact format also makes the set useful for routine servicing, a fresh build or a rebuild after wear on existing running parts. Kept alongside other workshop spares, the bearing pack gives a straightforward way to refresh the MB-01 chassis with the full quantity already counted out for the job.

Gears & motor pinions

MB-01 G-Parts Gears, chassis parts set

€4.79

The MB-01 G-Parts Gears set supplies drivetrain-related replacement parts for the MB-01 chassis, centered on a G-Parts sprue with a 65T spur gear and differential components. This layout gives the chassis a direct source for key internal gear parts when wear, damage or a full teardown calls for fresh hardware. Within the sprue, the 65T spur gear serves as a defined transmission component rather than a generic gear, while the differential parts address another separate section of the drivetrain. Keeping these parts grouped under the G-Parts designation helps match them to the MB-01 platform during workshop sorting and chassis maintenance. The set is aimed at repair, servicing and parts replacement for an existing model, not at a complete vehicle build. No scale is stated in the data, and the pack is identified specifically for the MB-01 chassis. On the bench, this set fits naturally into routine gearbox service, differential refresh work or a rebuild after heavy use. It also suits keeping a dedicated replacement sprue on hand for the MB-01, so the correct gear and matching internal parts are ready when the chassis is opened for maintenance.

Other spare parts & accessories

MB-01 LD-Parts Fr/Re. Lower Deck, chassis parts

€8.49

The MB-01 LD-Parts Fr/Re. Lower Deck provides the front and rear main chassis sections for the MB-01 platform, giving a model build the structural base that sits at the center of the assembly. These molded chassis parts are intended for replacement, repair or a fresh rebuild where the original lower deck needs to be restored with the correct form and mounting layout. The included parts consist of the main chassis front section and main chassis rear section. In the molded structure, raised side walls, screw mounting posts, recessed fixing areas and formed channels create the attachment points and alignment surfaces needed for surrounding assemblies. This kind of lower deck geometry matters in a chassis build because it determines how major components sit in relation to each other across the front and rear of the platform. The matched front and rear layout also helps maintain the intended fit of connected parts made for the MB-01 chassis. On the bench, these chassis sections suit routine maintenance, accident repair or the revival of a stored model that needs a new structural core. They also work well as workshop spares for MB-01 owners who keep replacement parts ready for ongoing running and rebuild sessions.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

MB-01 M-Parts, chassis spare parts sprue

€5.39

The MB-01 M-Parts sprue brings together several of the chassis pieces that matter most when an MB-01 build needs replacement hardware rather than a full new kit. This set is centered on the MB-01 platform and groups key black molded parts on one sprue, making it a practical match for repair work, routine maintenance, or keeping workshop stock ready for the next rebuild. Alongside suspension arms, the sprue also carries body mounts, a bumper and damper shafts, covering parts that sit across the running gear and upper mounting structure. That mix is useful when wear or impact affects more than one area at once, because the set addresses several connected mounting points in a single purchase. The molded layout also helps identify each piece before removal from the sprue, which keeps preparation straightforward at the bench. As a chassis parts set rather than a complete vehicle, it focuses on restoring original MB-01 component positions and connections. On the workbench, this sprue suits planned servicing as well as targeted replacement after track contact or repeated running sessions. It can be kept as a ready spare for an existing MB-01 chassis or used when a rebuild calls for fresh molded components in the suspension and body support areas.

Other spare parts & accessories

Mt.Beetle body mount parts, model accessory set

€12.99

This accessory set provides E Parts body mount components for the 58618 Mt.Beetle and supports accurate replacement work on the body mounting section of the build. The black molded pieces are supplied on a single sprue frame, giving a clear overview of the included shapes before removal and helping keep the parts organized during workshop preparation. Visible on the runner are several distinct molded forms, including bracket-like pieces, rod-shaped elements, a ring-shaped part, a slotted panel and a larger curved housing with round and square openings. That layout helps identify each section during repair or rebuild work and gives model builders the matching geometry needed for the intended mounting area. As a dedicated spare and replacement set rather than a general hardware assortment, it focuses on the specific fit and form required for the 58618 Mt.Beetle. The set works well when an existing chassis needs fresh mounting pieces after wear, loss or damage, or when a stored build is being brought back into running condition with matching replacement parts. It also suits bench stock for ongoing maintenance, where the correct molded components are ready for the next rebuild step.  Warning! Not suitable for children under 14 years.

Shock absorbers & springs

O-Ring 3x6mm Red, RC spare part for dampers

€3.39

This 10-piece pack of red O-rings in 3 x 6 mm format is made for damper and wheel axle use on selected RC chassis, giving a compact spare set for routine maintenance, worn seal replacement and parts-box stock. The small ring size suits jobs where a matching dimension matters, whether the work focuses on suspension service or axle-related fitting points. Compatibility is clearly defined across several chassis families. The O-rings can be used on TT-02, TT-02D and TT-02FT vehicles equipped with 50746, on TT-01 TYPE-E vehicles equipped with 53619, and on DT-03 or DT-03T vehicles equipped with 54567. TT-02RR lists this part as standard kit equipment. For DT-02, XB cannot be used, so chassis version and installed parts should be checked before fitting. In workshop use, a 10-pack keeps matching replacements ready for rebuilds, scheduled servicing or the correction of worn damper and axle seals after regular running sessions. The simple scope of delivery keeps the focus on the parts themselves: 10 O-rings for compatible RC maintenance tasks.  Warning! Not suitable for children under 14 years.

Screws & ball head screws

OF 5mm Adjusters L, RC accessory, open face

€5.59

OF 5mm Adjusters L is an RC accessory set for linkage tuning and replacement work on compatible models. The pack contains 8 open face reinforced adjusters, each with a 15 mm length, for use in place of standard 5 mm adjusters when a longer rod-end style connection is needed on a mechanical linkage. The instruction diagram shows the adjusters fitted to a threaded rod with grease applied to the threads before assembly. Installation also has a defined orientation: the side marked with a circle symbol is pressed onto the ball connector. That detail matters on steering and suspension style linkages, where the joint needs to seat correctly on the ball stud for clean movement. Different lengths are available separately, which helps keep the setup matched to the geometry required by the model. This set suits maintenance, replacement and setup changes on RC assemblies that use 5 mm adjusters. During fitting, some models may require filing down, depending on the surrounding layout and available clearance at the linkage point.

Screws & ball head screws

OF 5mm Adjusters M, RC accessory, open face

€5.59

The OF 5mm Adjusters M open face set adds a focused tuning and maintenance part for RC linkages, with 8 reinforced adjusters sized for use in place of standard 5 mm adjusters. The 11.5 mm medium length gives a concrete reference when matching an existing setup or planning a replacement during chassis work. The fitting method is clearly defined by the part design. Grease is applied to the threads before the linkage ends are screwed on, and the side marked with a circle is the side that presses onto the ball connector during installation. That orientation detail matters when assembling steering or suspension linkages, because the adjuster is designed to seat in a specific direction rather than as a symmetrical push-on part. The open face construction also supports direct use in rod-end style ball-joint connections where a standard 5 mm adjuster is being swapped out. On the bench, this 8-piece pack suits repair jobs, replacement of worn linkage ends, or small setup changes across compatible RC models. Some models may require filing down during fitting, so the part can be adapted where surrounding components leave limited clearance.

Shock absorbers & springs

Oil Damper VG O-Rings 30deg, damper parts

€9.19

Oil Damper VG O-Rings 30deg are replacement damper parts made to keep oil dampers working with a clean, responsive feel. The 30deg specification is tuned to support strong initial response, which is especially useful when older seals have started to lose their original performance during repeated running. The set contains 8 O-rings in a navy blue finish for routine maintenance or a planned damper refresh across multiple units. Their high-spec construction is designed to minimize the amount of air forced into the dampers while the model is moving, helping the oil circuit stay more stable through longer sessions. That reduction in trapped air supports more even damping behavior instead of the less consistent action that can appear as seals wear. As a focused replacement part, this set suits regular workshop servicing as well as targeted tuning when damper response needs attention. During rebuilds, race-day maintenance, or general suspension servicing, a fresh set of O-rings can make a noticeable difference to how smoothly the dampers cycle. Keeping spare seals on hand also helps maintain a dependable setup between runs when worn internal parts need a direct replacement.

Shock absorbers & springs

On-Road Spring Set, tuning accessory, hard medium soft

€21.29

This on-road spring set adds a wider suspension tuning range to compatible RC chassis with 6 springs in hard, medium and soft rates. The colour-coded finish in fluorescent red, fluorescent yellow and fluorescent blue makes each rate easy to identify during setup changes, helping keep adjustments organised between test sessions and repeat runs. The set is described as a softer spring kit than OP440, which opens another direction for chassis tuning when a setup calls for more compliant suspension response. It is intended for use across a broad group of platforms including F104PRO II, F104W, F104, F103GT, M-07 CONCEPT, M-06, M-06 PRO, M-05 ver.II PRO, M-05, M-05 PRO, MF-01X, TT-02FT, TT-02RR, TT-02D, TT-02 and TT-01 TYPE-E. For F104 and F104W chassis, the data specifies use with 53901. On the workbench, the 3 spring rates support direct comparison of suspension behaviour during circuit setup, whether the focus is front-end response, overall balance or matching the chassis to track conditions. Scope of delivery: 6x springs hard, medium, soft.  Warning! Not suitable for children under 14 years.

Gears & motor pinions

Pinion Gear-Set 16/17T Alu M0.6 for RC Chassis

€8.99

This aluminum pinion gear set brings 2 tooth-count options to compatible RC chassis, with one 16T gear and one 17T gear in M0.6 pitch for drivetrain replacement or gearing changes. The silver-finish parts have a compact machined form, and each pinion is secured with a grub screw for firm mounting on the motor shaft. The set is intended for clearly defined chassis combinations rather than general use. TT-02FT, M-05, M-05 PRO, M-05 ver.II PRO, M-06 and M-06 PRO chassis use only the 16T gear. XV-02PRO, TA07 PRO, TA08 PRO and M-08 CONCEPT chassis use only the 17T gear. For F104PRO II chassis, the set is used with 51609. For TA07 MS chassis, only the 17T gear is usable and it is used with 51356, 51423 and 51548. Scope of delivery: 2 pinions and 2 grub screws. That makes the set a practical choice for workshop stock, scheduled maintenance or a direct replacement when a specific chassis calls for one of these tooth counts. In a bench setup, the stamped 16 and 17 markings help identify the correct gear quickly before installation, keeping chassis-specific drivetrain work clear and organized.  Warning! Not suitable for children under 14 years.

Gears & motor pinions

Pinion Gear-Set 18/19T Alu M0.6, RC gear set

€9.99

The Pinion Gear-Set 18/19T Alu M0.6 brings 2 aluminum motor pinions into one compact drivetrain set, with 18T and 19T tooth counts for compatible Tamiya chassis. Each gear mounts with a grub screw, creating a firm connection on the motor shaft for controlled power transfer through the drivetrain. This set is intended for tuning, replacement and maintenance work across several chassis families. It fits M-05, M-05 PRO, M-05 ver.II PRO, M-06, M-06 PRO, WR-02, WR-02G, WR-02C and WR-02CB chassis. Use on some platforms follows specific tooth-count rules: GF-01CB uses only the 18T pinion, while TT-01 TYPE-E and TT-01D TYPE-E use only the 19T pinion. F104PRO II uses the set with 51609, TA07 MS Chassis uses it with 51356, 51423 and 51548, and F103GT uses only the 18T pinion with 50506. In workshop use, the 2 included pinions give a straightforward way to compare gearing options during a rebuild or drivetrain refresh. The M0.6 specification keeps the set aligned with matching gear applications, whether the goal is restoring a worn drive part or preparing a chassis for a different running setup.  Warning! Not suitable for children under 14 years.

Gears & motor pinions

Pinion Gear-Set 22/23T Alu M0.6, RC gear set

€9.99

This pinion gear set brings 2 aluminum motor pinions into one compact drivetrain upgrade for compatible RC chassis. With 22T and 23T tooth counts and an M0.6 specification, it supports clear gearing choices when adjusting acceleration response or matching a replacement part during maintenance. Each pinion is machined with a central bore and a side threaded hole for the grub screw, so the gear mounts directly to the motor shaft in a straightforward mechanical layout. The included contents are 2 pinions and 2 grub screws. The 22T and 23T markings on the gears make identification quick during setup, storage or parts sorting. Aluminum construction keeps the set focused on a precise drivetrain component rather than a general hardware mix. For TT-01 TYPE-E chassis, the set offers both tooth-count options, while TT-01D TYPE-E chassis can use only the 22T gear. On the bench, this set suits routine replacement work, ratio comparison between 22T and 23T, or keeping a second pinion ready in the parts box for compatible RC running sessions. It also fits neatly into a workshop stock of drivetrain spares where exact tooth count and pitch matter.  Warning! Not suitable for children under 14 years.

Gears & motor pinions

Pinion Gear-Set 24/25T Alu M0.6, motor pinion set

€10.79

This motor pinion set brings a focused drivetrain upgrade to compatible RC chassis with 2 aluminum pinions in 24T and 25T plus 2 grub screws for mounting. The M0.6 gear specification makes it a targeted choice for model builders who need the correct tooth pitch for matching transmission parts and a clean fit on the motor shaft. The set is intended for several established chassis platforms in the Tamiya range. It fits M-07 CONCEPT and M-08 CONCEPT chassis, with the note that only the 24T pinion can be used on M-08 CONCEPT. It also fits TT-01 TYPE-E and TT-01D TYPE-E chassis, where it is used with 53665. That compatibility detail matters during drivetrain setup, because the pinion must match both the chassis layout and the related gear components already in use. The aluminum construction adds a crisp machined finish and a precise look that suits technical RC assemblies. On the bench, this set supports replacement work after wear or a gearing change during a fresh build. In workshop use, the 2 included pinions give a direct choice between 24T and 25T, while the grub screws complete the mounting hardware needed for installation.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

R/C Body Mount Hole Patches, RC accessory, 0.5 mm

€6.69

These R/C body mount hole patches add discreet reinforcement where bodyshells take repeated stress. The clear 0.5 mm material strengthens the area around each mounting point while leaving the shell finish visible, so repairs stay unobtrusive on painted or decorated bodies. Each sheet provides 8 patches, giving several mounting points the same treatment in one session or leaving spares ready for later maintenance. The 6.5 mm internal diameter is sized for use on most body mount holes, making the patches a straightforward choice for many R/C bodyshell layouts. Their ring format focuses support around the opening itself, where cracks and widening can start after repeated fitting, removal and running. In workshop use, the patches suit routine bodyshell upkeep before damage spreads further around the post area. They also work well when refreshing a frequently used shell, helping keep mounting holes neat through repeated body changes between running sessions. This accessory is intended for model hobby use and is marked 14 years and up.

Other spare parts & accessories

RC Servo Saver Kit, universal chassis accessory

€6.79

This RC servo saver kit adds an adjustable steering connection for a wide range of chassis layouts while helping reduce shock loads passed into the servo during running. The set is designed for universal use and is listed for many Tamiya platforms including M-06, M-06Pro, F104, F104 Pro II, DT-02 and DT-03, making it a practical choice for repairs, replacements or fresh steering setups. Several servo saver bases are provided so the mounting interface can be matched to different servo makes. The instruction data names base options for Futaba, Sanwa, Acoms, JR and KO, allowing the spline connection to be selected according to the servo in the chassis. Two spring rates are included: S6 strong and S9 weak. The assembly diagrams also show separate configurations for off-road car and racing car use, with S3 or S5 upper parts chosen according to the layout. Mounting hardware covers 3 mm x 12, 2.6 mm x 10 and 2 mm x 10 screw formats, with S1 and S2 spacers assigned to the screw diameter. During setup, the saver arm can be arranged to suit the direction of the servo in the car, and the linkage can be attached by cranked rod or by ball pin depending on the steering system in use. That makes the kit useful both when restoring an older chassis and when refining a custom RC build around the available servo and linkage parts.  Warning! Not suitable for children under 14 years.

Screws & ball head screws

Router Ctrsk Bit for 2mm Screw, tool accessory

€7.19

The Router Ctrsk Bit for 2mm Screw is a workshop accessory for cutting neat countersunk holes in small machine parts. Its diamond particle coated conical head removes material cleanly in carbon fiber, FRP and similar surfaces, so 2 mm countersunk screws can sit flush instead of leaving the head raised above the part. Beyond countersinking, the flat sides of the head can be used to shape edges during detail work. The #200 particle size gives the abrasive surface a defined cutting character for controlled material removal on compact components. This makes the bit useful when refining Mini 4WD parts that need a cleaner screw seat or a tidier edge profile. Made for use with routers such as the Tamiya Electric Handy Router Item 74042, it supports focused modification work where accuracy matters on every pass. On a tuning bench, the bit helps prepare carbon fiber and FRP parts for a lower-profile screw fit that keeps surfaces cleaner around mounting points. It also suits small finishing jobs where edge shaping and countersinking are handled with the same accessory in a compact tool setup.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

Rubber Tire Cement LoVis. 25g, RC tire adhesive

€14.49

Rubber Tire Cement LoVis. 25g is a dedicated CA cement for R/C car rubber tires, made for clean bonding work where a tire bead meets the wheel. The low-viscosity formula flows smoothly into narrow seams, so the adhesive can reach the joint itself instead of sitting on the surface. The bottle contains 25 g of cement and uses a fine nozzle for controlled application in small contact areas. That layout helps when working around the full circumference of a wheel, where steady placement matters more than excess glue. The adhesive is supplied in a bottle with an aluminum bag that limits humidity during storage. In workshop use, that added protection supports more consistent handling when the cement is opened again for later tire maintenance. The source data identifies this as CA cement for rubber tires, giving it a focused role within R/C car setup rather than general household bonding. It fits naturally into bench work before track sessions, when fresh rubber tires are mounted to wheels and the bead needs an even seal. It also suits repair tasks after running, when a lifted section at the joint calls for careful re-bonding with a smooth-flowing adhesive.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

Sand Scorcher Rear Guard, model accessory

€10.29

This rear guard is a dedicated model accessory for the Sand Scorcher and is listed for chassis references 58441 and 58452. The included contents are 1 protective bar, giving a clearly defined replacement part for the rear section rather than a mixed hardware assortment. Its focused single-part format helps when a specific rear component needs to be replaced during maintenance, repair or restoration work. The stated fitment to 58441 and 58452 keeps compatibility clear at a glance and supports accurate parts selection for the matching Sand Scorcher versions. Because the set contains one rear protective bar, the part can be kept on hand for workshop stock, planned rebuilds or the replacement of a missing original component. On the bench, this accessory suits routine service work where the rear section needs the correct guard rather than a universal substitute. It also fits restoration projects that aim to return a Sand Scorcher to its intended rear layout with the proper dedicated replacement part.  Warning! Not suitable for children under 14 years.

Screws & ball head screws

Screw Bag D BD1-7, model hardware set

€10.89

Screw Bag D BD1-7 is a model hardware set built around the small fastening parts that keep an assembly moving. The pack brings together metal screws, hex nuts, flat washers, split lock washers and threaded spacers, giving compatible model builds the exact kind of joining and spacing parts that are often needed during maintenance or part replacement. The combination of different fastener types supports more than one task within a build. Screws and nuts handle fixed connections, washers sit between parts to spread contact, and split lock washers help hold tightened joints in place. Threaded spacers add distance where mounted sections need clearance between components rather than direct contact. This makes the set useful not only when hardware has been lost, but also when an older build is being refreshed with matching replacement fittings. On the bench, the assortment suits repair sessions, rebuild work and careful parts sorting before assembly starts. The compact hardware format also makes it practical to keep alongside compatible model kits as a dedicated source for replacement fixings when a single missing fastener would otherwise stop progress.

Other spare parts & accessories

Servo Saver P-Parts Set for DT-03 and DF-03

€4.49

This servo saver P-parts set is made for compatible DT-03, DT-02 and DF-03 chassis and supplies the shaped components needed when the original steering parts need replacement. The runner format keeps each piece organised and easy to identify before removal, which helps when checking parts against the build or service instructions. The moulded frame shown here carries numbered components, including ring-shaped and bracket-style pieces used within the servo saver assembly. That layout supports careful maintenance because each part stays attached until the moment it is needed. For older kits, workshop repairs, or chassis refreshes, a dedicated spare set like this helps return the steering mechanism to its intended configuration without substituting unmatched pieces. On the bench, the set suits routine servicing, rebuilds after heavy running, or the completion of a partly used kit where original P-parts are no longer available. It also works as a practical stock spare for model collections built around the DT-03, DT-02 or DF-03 platform.  Warning! Not suitable for children under 14 years.

Screws & ball head screws

Servo Step Screws, aluminum accessory set of 4

€10.89

These aluminum servo step screws are made to improve the way a servo sits in its mounting points, combining a precise fit with a clean hardware layout. The set contains 4 screws, each shaped to suit holes between 4.5 mm and 5 mm, so the screw seats more securely in the opening instead of relying on extra spacing parts. The metallic finish and machined form give the hardware a crisp technical look that matches detailed model builds and electronics work. A stepped profile is the key feature here. By filling the mounting hole more accurately, the screw helps reduce play at the fixing point and supports a tighter connection around the servo case. The integrated shoulder also means separate washers are not required, which keeps the installation simpler and leaves fewer loose parts to track during routine servicing. Hex socket heads add another practical detail, allowing a tool to seat firmly in the screw head for controlled tightening in compact spaces. These screws suit upgrade work, replacement hardware needs, or a fresh servo installation where a closer fit is wanted at the mounting holes. Depending on the servo design, only 2 screws may be needed, leaving the remaining hardware available as spares for later maintenance or another compatible setup.

Axes & drive shafts

Shaft 2 x 9.8 mm, model spare part, 10 pcs

€3.99

This spare shaft set brings exact replacement dimensions to model maintenance with 10 steel shafts measuring 2 x 9.8 mm. The compact format suits small mechanical assemblies where a worn, bent or missing shaft can affect how connected parts sit and move. The 2 mm diameter and 9.8 mm length give a clear reference for matching an existing part before installation. As a workshop consumable, the set supports repeated servicing across compatible hobby models instead of relying on a single replacement piece. The short shaft format is suited to detail areas where space is limited and clean alignment matters. Keeping identical spares on hand can simplify routine upkeep when several connection points use the same measurement. In a home workshop, club pit area or model bench, this shaft pack fits neatly into regular maintenance supplies for ongoing repair work. It also serves as a practical stock addition when checking assemblies, replacing lost hardware or preparing compatible builds for the next running session.  Warning! Not suitable for children under 14 years.

Shock absorbers & springs

Silicone Damper Oil Hard Set, RC oil, #800/900/1000

€20.991 l = €349.83

The Silicone Damper Oil Hard Set brings firmer suspension tuning to RC maintenance with 3 silicone-based oils in grades #800, #900 and #1000. Each bottle contains 20 cc, and the pointed applicator nozzle helps guide the fluid into compact damper bodies with controlled dispensing during rebuilds or setup work. This set is intended for oil pressure dampers and is tailored to Tamiya applications where damping changes are part of chassis adjustment. Higher viscosity means thicker oil and a harder damping feel, so the three grades in this set give a practical range for comparing response and refining how a model settles through corners, braking zones and uneven sections. The bottles are colour coded as pink, clear and light blue, making the three viscosities easier to distinguish on the bench. The fluid is identified for shock absorber use on model vehicles, and the set can also extend the available tuning range when combined with the softer companion sets in the same series. Compatibility listed in the data covers CC-01, F103GT, TB-03 and TB-03 VDS chassis. That makes the set a useful workshop supply for regular servicing, seasonal retuning or keeping several RC builds ready with different damper fills for changing surfaces and handling preferences.  Warning! Not suitable for children under 14 years.

Shock absorbers & springs

Silicone Damper Oil Medium Set #500 #600 #700

€20.991 l = €349.83

This silicone damper oil medium set brings 3 tuning grades together for model vehicle shock absorbers: #500, #600 and #700. The three 20 cc bottles cover the medium range in Tamiya's viscosity system, where a lower number indicates a lower viscosity and a higher number indicates a thicker oil, making step-by-step suspension changes easier to plan at the workbench. The set is intended for model vehicles and uses silicone-based oil in 3 colour-coded grades: green #500, blue #600 and purple #700. At 25 °C, the kinematic viscosities are 500 mm2/s, 600 mm2/s and 700 mm2/s. This spacing supports direct comparison between nearby setups instead of forcing a large jump in damping feel. The pointed bottle tips support controlled dispensing into damper bodies during filling, topping up or rebuild work, and the 20 cc fill quantity on each bottle gives enough material for repeated service sessions. On an RC chassis, these 3 grades can be used when refining how quickly the suspension moves over bumps, settles after compression or reacts to changing grip levels. The set suits routine maintenance as well as test sessions where several oil weights are compared back to back on the same model vehicle.

Shock absorbers & springs

Silicone Damper Oil Soft Set, RC model accessory

€20.991 l = €349.83

This silicone damper oil soft set brings suspension tuning into a clearly graded format with 3 bottles covering #200, #300 and #400 viscosities. The softer range supports fine adjustment of oil-filled dampers on RC model vehicles, whether the goal is a lighter response over uneven sections or a more measured starting point for chassis setup at the workbench. Each bottle contains 20 cc and uses a narrow nozzle that helps guide the fluid into damper bodies with controlled application. The set is identified by red, orange and yellow oils, making the grades easy to separate during rebuilds, refills and comparison testing. The formula is silicone-based and intended for model vehicle shock absorber use. Tamiya's viscosity system follows a simple rule: lower numbers indicate lower viscosity, while higher numbers indicate thicker oil. This soft set can also extend its adjustment range when used together with the medium and hard sets in the same series. Compatible applications named in the data include the GB-01S chassis, CC-01 chassis, F103GT chassis, TB-03 chassis and TB-03 VDS chassis. On a tuning bench, the 3 grades allow direct back-to-back damper changes between runs or during a rebuild, with each step in viscosity offering a clear reference point for suspension experimentation.  Warning! Not suitable for children under 14 years.

Shock absorbers & springs

Silicone Diff. Oil #3.000, model supply, 40cc

€9.391 l = €234.75

Silicone Diff. Oil #3.000 is a model supply for tuning oil-filled sealed differential units and roll dampers in R/C cars. The 40cc bottle and narrow nozzle suit careful, repeatable application at the bench when a setup calls for a 3000 weight fluid on faster layouts with long, sweeping turns. The fluid is identified in the technical data as polydimethylsiloxane, with a kinematic viscosity of 3,000 mm2/s at 25 °C. It is a liquid, odourless and insoluble in water, with a relative density of 0.97 at 25 °C. That specification gives a clear reference point when matching maintenance supplies to an existing differential fill or a planned roll damper setup. The bottle format keeps the quantity compact for workshop storage while still covering repeated servicing across compatible R/C car drivetrains. In use, the oil suits rebuilds of sealed differentials after cleaning, routine setup changes between track conditions, or roll damper servicing on formula and RM chassis. On a pit table or home workbench, the 40cc fill offers a practical amount for keeping one viscosity grade ready for regular tuning work.  Warning! Not suitable for children under 14 years.

Shock absorbers & springs

Silicone Diff. Oil #4000, differential oil, 40cc

€8.991 l = €224.75

Silicone Diff. Oil #4000 is a tuning fluid for oil gear differentials that brings a clear handling change to model vehicles. The high-viscosity grade is intended to support stable, speedy cornering in the high-speed range, making it a useful choice when differential action needs a firmer setup on faster sections. The bottle contains 40cc of yellow silicone oil and is sized for about 22 uses in touring car different gears. Its bottle format with dispensing nozzle supports measured application during maintenance, refills, or setup changes at the bench. The fluid is identified as #4000 viscosity, and the supplied data lists a kinematic viscosity of 4,000 mm2/s at 25 °C. This Hop-Up Option is intended specifically for model vehicle differentials that use oil as part of their tuning setup. On indoor tracks, club circuits, or home workshop setups, the oil can be used to compare differential feel against lower-viscosity grades and refine how the car responds through faster corners. It suits repeated testing sessions where small setup changes matter, while the 40cc volume keeps enough fluid on hand for ongoing drivetrain maintenance.

Other spare parts & accessories

Sponge Tape for Bumper, model accessory, 10-pack

€4.99

Sponge Tape for Bumper is a compact model accessory for fine-tuning fit in RC car setups. Each foam strip measures 150 x 15 x 2 mm and is shaped to sit neatly where a small gap needs to be taken up. Used between a urethane bumper and the body, the tape helps the shell sit more closely against the chassis line, which can support steadier handling on the race track. The same foam material also serves as a spacer on battery holders. Placed between the battery pack and the chassis area, it creates a tighter contact point that helps reduce movement during running. That makes this 10-pack useful not only for body mounting adjustments, but also for routine setup work across multiple cars or repeated rebuilds. The narrow strip format is easy to trim or position according to the space available, while the 2 mm thickness gives a defined layer for controlled spacing. In workshop use, the tape suits quick pre-run checks, replacement during maintenance, or small chassis adjustments before track sessions. It is a straightforward addition for racers who want closer body fit, tidier battery seating and a more dialed-in setup from simple, measurable material changes.

Other spare parts & accessories

Stabilizer Rod Stopper (4), RC chassis hardware

€11.99

The Stabilizer Rod Stopper (4) is a small but important tuning part for RC chassis stabilizer setups. Each collar is fitted onto the sway bar and tightened with a grub screw to hold its position on the rod, so the bar can pivot up and down as intended while lateral movement is kept under control during loaded cornering. The set includes 4 stabilizer collars and 4 grub screws. This layout supports left and right positioning on a stabilizer assembly and gives a clean mechanical stop on the rod itself. The stopper design works as part of the stabilizer system rather than replacing the bar, and it is used with matching sway bar sets on specified chassis. Compatible applications listed in the data include TA06, TA06 PRO, TA06 MS, TB-04, TB-04 PRO, FF-03, FF-03 PRO, TB-03, TB-03 VDS, TA05 ver.II, M-07 CONCEPT, M-08 CONCEPT, TRF502X and DB02, each with the corresponding referenced set. On a touring car sedan setup, this kind of lateral control helps the stabilizer work consistently through repeated laps and setup changes. It suits maintenance, replacement and fine tuning on compatible chassis builds where accurate bar location matters to suspension response.

Screws & ball head screws

Step Screw 3x14mm BB1, model spare screws

€2.19

Step Screw 3x14mm BB1 is a model spare screw set for builds and repairs that call for this exact hardware format. The pack contains 10 screws, giving a ready supply for maintenance tasks where matching dimensions matter and mixed fasteners can interrupt progress. The 3x14 mm specification provides the key reference for selecting the right screw for a compatible assembly, while the BB1 designation adds a second identification point for parts matching. This combination helps when replacing missing hardware, sorting workshop stock or keeping a current project aligned with its intended screw type. As a dedicated spare part, the set supports precise fastening work in model assemblies that rely on consistent screw sizing. On the bench, the 10-piece pack suits routine servicing, partial rebuilds and keeping reserve hardware available between sessions. It also fits neatly into parts storage for quick access when a compatible model needs the same screw again.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

T3-01 Battery Case, chassis accessory, 4xAA

€21.79

The T3-01 Battery Case adds a dedicated 4xAA power option to compatible T3-01 chassis models and gives the Dancing Rider kit an alternative to NiCD, NiMH or Lithium Ion battery packs. The holder is built around a 6V AA layout, with polarity markings in the tray to guide battery placement and a wired connector lead to link the case to the chassis electronics. Inside the assembly, metal battery terminals, springs, screws and the case sections come together as one complete battery compartment. The closure uses a twist-shut cap that can be turned with a coin, keeping the batteries secured once installed. Red and black cable routing is part of the assembly layout, and the connector orientation matters for correct connection to RC equipment. The case is intended for use with 4 AA alkaline or rechargeable batteries and a compatible ESC. Batteries are not included. This accessory suits T3-01 owners who want a separate battery holder matched to the chassis rather than a rechargeable pack format. It fits naturally into maintenance, replacement or conversion work on a Dancing Rider setup, especially when keeping a ready AA-powered option alongside existing running gear.

Shock absorbers & springs

TA-/TB-/TRF Urethane Front Bumper RC Part

€4.59

The TA-/TB-/TRF Urethane Front Bumper is a chassis tuning part for selected Tamiya on-road platforms, using a larger-than-standard bumper profile to reduce the gap between chassis and bodyshell. That closer fit helps suppress body shimmy during high-speed running, giving the shell steadier support at the front of the car. The part is supplied as 1 foam rammer and is shaped as a curved bumper insert with 2 mounting holes and edge cut-outs for installation on compatible layouts. Supported chassis named in the data include TA07 MS Chassis, TA07 PRO Chassis, TA05 ver.II Chassis, TB-Evo.7 Chassis, TB-Evo.6 MS Chassis, TB-Evo.6 Chassis, TB-05 PRO Chassis, TB-04 Chassis, TB-04 PRO Chassis, TB-03 chassis, TB-03 VDS Chassis, TRF419XR Chassis, TRF419X Chassis and TRF419Chassis. As a front-end setup part, it focuses on shell support rather than decoration, making it relevant where close body fit and controlled movement matter on faster laps. It suits rebuilds, maintenance and setup changes on compatible touring chassis already in use. During track preparation, the larger bumper profile can be fitted when a closer bodyshell position is needed at the nose of the car for more settled running at speed.  Warning! Not suitable for children under 14 years.

Gears & motor pinions

TA-01 DF-01 G Parts Gear Set for RC Models

€14.99

The TA-01/DF-01 G-Parts gear set focuses on the mechanical core of compatible RC model assemblies, with injection-moulded components shaped for drivetrain and gearbox-related service work. Visible in the set are a large spur gear with an integrated central bevel gear, 2 medium cylindrical gears with fine outer teeth, smaller gear-form parts on a sprue, and 2 round disc-shaped pieces with raised pegs and centre holes. These parts support repair and replacement tasks where worn, missing or damaged transmission elements affect the running condition of a TA-01 or DF-01 based build. The different tooth forms, mounting holes and moulded connection points indicate use in geared drive sections rather than body or decorative areas. As unassembled service parts, the set gives builders the correct component shapes needed for maintenance without requiring improvised substitutions. On the workbench, the clearly separated moulded pieces help with checking fit before installation and with comparing old and new parts during a rebuild. This makes the set useful for planned servicing as well as for bringing an older chassis back into operating condition after drivetrain wear or gear damage.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

TA-01/02 Front Gear Case, 4WD spare parts, red

€13.99

This spare parts set supplies the red front gear case components for TA-01 and TA-02 4WD models, giving repair and maintenance work the exact housing parts needed for the front transmission area. The A parts tree contains 14 pieces, making it a focused replacement set for restoring the original layout rather than a general assortment. The molded sections shown here cover the front gearbox housing area, with matching red parts that help separate this assembly from other chassis sections during workshop sorting. The set is intended for model servicing where a cracked case, missing section or worn mounting point needs replacement with the correct designated parts. Included metal pins add the small hardware required for the assembly, so the gearbox section can be rebuilt with the supplied connecting elements from this pack alone. On the bench, the clearly grouped A parts support a straightforward check of each housing section before installation. For ongoing TA-01/02 upkeep, this set suits planned maintenance, accident repair and the restoration of older 4WD chassis that need the original front case structure in red.  Warning! Not suitable for children under 14 years.

Gears & motor pinions

TA-01/02/DF-01 Ball Diff. Unit, RC spare part

€43.99

The TA-01/02/DF-01 Ball Diff. Unit is a dedicated RC spare part for compatible TA-01, TA-02 and DF-01 chassis, bringing the differential section back into working order with a matching replacement assembly. As a ball differential, it is intended for the drivetrain, where controlled internal movement helps manage how drive is transferred through the gearbox during running. The set is supplied as 1 ball differential with 8 pieces, giving the core parts needed for this specific maintenance job rather than a mixed assortment of unrelated hardware. The accompanying assembly information refers to ball differential grease during installation, showing that this unit is built as a serviceable mechanical component rather than a sealed module. Documented elements such as the differential spur gear, gearbox joint, hexwrench steps and placement notes point to a structured assembly sequence with attention to part orientation. That makes the unit relevant for repair benches, rebuild projects and routine drivetrain upkeep on older compatible chassis. In workshop use, the unit fits naturally into a maintenance cycle that includes inspection, replacement of worn drivetrain parts and reassembly of the gearbox area. For existing TA-01, TA-02 or DF-01 models, it provides a direct route to keeping a compatible chassis in running condition with the correct differential format.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

TA-01/02/FF-01 C-Parts, rear upright spare set

€12.79

The TA-01/02/FF-01 C-Parts rear upright set is a chassis-specific spare for compatible Tamiya models, supplying the moulded parts needed in the rear upright area on a single black sprue. For repair, maintenance or a careful rebuild, the matched layout keeps related pieces together and ready for selection at the bench. The injection-moulded frame holds several components in their original positions until removal, which helps preserve part identification during preparation and fitting. Mirrored shapes for left and right assembly can be checked before cutting from the runner, reducing mix-ups when replacing worn or damaged suspension-side parts. The sprue format also supports clean storage between repair sessions, since unused pieces remain attached and easier to track than loose small parts. Visible moulded markings on the runner further reflect its role as a functional service part for model maintenance. This spare set fits situations where a compatible chassis needs renewed rear upright components after use, damage or a missing part in a long-running build. It also suits keeping a dedicated replacement sprue on hand for workshop stock, so servicing can stay focused on the exact chassis section rather than replacing unrelated assemblies.

Other spare parts & accessories

TA-01/02/FF-01 D-Parts Body Mount Set

€9.59

This D parts body mount set is made for TA-01, TA-02 and FF-01 model platforms and supplies the core hardware used to position and secure a bodyshell on the chassis. The 22-piece pack combines molded mounting parts with the small metal fixings needed for installation, making it a practical replacement when original body supports are missing, damaged or worn. The set contains 4 long upright posts with a row of adjustment holes, 2 angled mounting arms, 6 screws and 10 metal body clips. That layout supports the usual body-post setup used on compatible on-road chassis, where the shell sits over the posts and is locked in place with clips through the selected holes. The multiple hole positions allow the shell to sit at the required height for the specific bodyshell and mounting point arrangement already on the model. The angled brackets provide the base connection between the posts and the chassis structure. Used during repair, restoration or routine maintenance, this spare parts set helps return a TA-01, TA-02 or FF-01 build to a complete mounting setup. It also suits workshop stock for keeping compatible chassis ready for shell changes, rebuilds and replacement of lost clips or screws after running sessions.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

TA-01/02/TB-01/02/TG Wheel Axle Set, RC spare part

€12.79

This RC spare part set supplies 2 metal wheel axles for compatible TA-01/02, TB-01/02 and TG chassis, giving a direct replacement option where a 39 mm axle is specified. The machined shape combines a threaded end, a cross-hole and a slotted coupling section, so the part matches the connection points used in these model vehicle platforms. The 39 mm format is the key reference for installation planning and parts matching. The pair layout supports side-to-side replacement with matching hardware rather than mixing old and new axle parts. The metal construction shown in the data suits a mechanical role where rotation, fastening and drivetrain connection meet in one compact component. Because the set is defined for TA-01/02, TB-01/02 and TG chassis, the copy stays focused on those stated applications only. In workshop use, this axle set suits routine maintenance, repair after wear, or restoring a compatible chassis to running condition with the specified part format. The 2-piece scope of delivery keeps the contents clear for parts drawers, bench stock and planned service work on supported RC models.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

TA-01/DF-01 Chassis, RC chassis spare part

€23.99

The TA-01/DF-01 Chassis is a molded replacement chassis section for compatible RC model builds, providing the main structural base for reworking a worn frame or completing a repair with the correct platform shape. Its black molded construction uses a ribbed interior layout and a honeycomb reinforcement pattern, giving the part a defined geometry for mounted assemblies while keeping the form focused on mechanical function. The underside shows multiple screw bosses, fastening holes and raised perimeter walls that help position matching components at fixed points across the chassis. An oval cutout on one side and fork-like extensions at the opposite end are integrated into the molding, showing that this is not a generic plate but a chassis section shaped for a specific TA-01/DF-01 layout. The glossy finish comes from the molded surface itself, while the internal bracing and recessed sections are designed around fitment and support. As a spare part, it suits restoration work, replacement after damage, or keeping a compatible workshop build in running condition. On the bench, the chassis gives a clear base for reinstalling drivetrain and mounted hardware in their intended positions. In an ongoing RC collection, it also serves as a practical replacement part for maintaining older compatible models rather than leaving a build incomplete.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

TA-01/DF-01 Upright (2), RC spare part, black

€8.69

TA-01/DF-01 Upright (2) is a black RC spare part set for compatible TA-01 and DF-01 chassis builds, supplying 2 mirrored uprights on a single molded sprue for direct replacement work. The paired form supports left and right side installation, making it easier to restore the original mounting layout when an existing part is worn, cracked or missing. Each upright is injection-molded and shaped with cylindrical mounting sections, angled arms and reinforcing ribs that support the part where screws or pins pass through the fixing points. The molded geometry is designed for chassis assemblies that rely on precise alignment between connected components, so replacement with the correct upright helps maintain clean mechanical fit. The central sprue keeps both matching pieces together until installation and helps identify the set as one complete replacement pair. This spare part suits workshop use during routine maintenance, rebuilds after running wear, or parts-box preparation for TA-01 and DF-01 platforms. Kept on hand with other service components, the 2-piece set supports faster repairs when suspension or wheel-mount areas need attention.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

TA-01/TA-02 B-Parts, gearbox rear parts set

€18.99

This replacement parts set is made for the rear gearbox section of TA-01 and TA-02 based models and comes as a black molded B-parts sprue with 7 individual components. The layout keeps related pieces together on one tree, making it easier to identify the required shapes during maintenance or a focused rebuild of the drivetrain housing area. The stated compatibility references 58136, 58146 and 58154, giving clear model numbers for checking an existing build before fitting. As a dedicated B-parts set, this pack suits repairs where the original rear gearbox components are damaged, incomplete or no longer usable. The black finish matches the supplied parts designation, while the molded format supports clean separation of each piece during assembly. The included contents are 1x B parts tree with 7 parts. On the workbench, this set supports targeted servicing without replacing unrelated sections of the chassis. It fits naturally into a repair routine that starts with model-number checking, then moves to part removal, sprue separation and installation in the rear gearbox area of the compatible TA-01 or TA-02 build.  Warning! Not suitable for children under 14 years.

Gears & motor pinions

TA-02 Gear Set, RC spare part, 15-piece drivetrain

€12.99

The TA-02 Gear Set is a dedicated RC spare part set for transmission repair, built around the updated gear layout shown for this drivetrain. Its 15 included pieces support service work on compatible TA-02 based models, with the main revision centered on a one-piece molded spur and drive gear that replaces the earlier separate parts arrangement. This change brings the large spur gear and the smaller drive gear together in a single repair component, so the transmission uses the revised integrated format specified for this set. The package also uses an idler gear in resin instead of the earlier metal version, and the ball retainer specification is G4. These details matter when replacing worn internal drivetrain parts, because the set is designed around that exact update rather than a generic mix of gears. The scope of delivery is 1 gear set with 15 pieces. On the workbench, the set suits planned transmission overhauls as well as targeted replacement of worn gear components after regular RC running. It is intended for compatible TA-02 applications and is not compatible with 1/10 R/C off-road buggies, making the fit context clear before installation begins.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

TA-02/CC-01/FF-01 Front Upright Pair, RC Spare Part

€7.29

This spare part set is made for TA-02, CC-01 and FF-01 chassis and supplies 2 black front uprights for the steering end of the front axle. The mirrored left and right layout supports a matched fit during repair work and helps restore the intended geometry at the front wheel mounting points. Each upright is moulded with a circular hub opening, fastening holes and a reinforced arm section that connects into the surrounding steering hardware. The ribbed structure adds material where the shape changes direction, while the drilled connection points support accurate screw-based installation with the corresponding chassis parts. As a dedicated replacement part, the set focuses on the front upright area rather than a universal fit across unrelated platforms. The pair suits routine maintenance, rebuilds after wear, or the completion of an older TA-02, CC-01 or FF-01 chassis project. In workshop use, the 2-piece set makes it possible to replace both front sides together and keep the steering assembly consistent across the axle.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

TA-02/FF-01 Front Upright, spare part, blue

€8.69

The TA-02/FF-01 Front Upright blue set supplies 2 replacement uprights for compatible front-end assemblies. Each part is formed as a mirrored counterpart, so the left and right sides can be positioned correctly when restoring the steering or suspension layout on a TA-02 or FF-01 chassis. The shape combines a large cylindrical hub section with a smaller upper mounting point and a flat arm with a fastening hole. Reinforcing ribs add structure to the moulded form, and the visible metal insert at the upper mount provides a ready fixing point within the assembly. The blue colour helps separate this pair from other small chassis parts during sorting, servicing and rebuild work. As a dedicated spare part, this set is intended for precise replacement rather than general-purpose adaptation. The 2-piece format suits routine maintenance, repair of worn front components or keeping matching replacements on hand for workshop use. In a build area or pit box, the mirrored pair can be checked against the existing front assembly before fitting, helping keep the chassis layout consistent on both sides.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

TA-05/TB Evo.IV B-Parts Body Mount Set

€15.99

The TA-05/TB Evo.IV B-Parts Body Mount set provides the dedicated mounting components used around the body support area on compatible chassis. With 12 black moulded parts in one pack, it covers the component group needed when the original posts, braces or mounting pieces need replacement during maintenance or rebuild work. The set is listed as B parts and is supplied as 1x parts pack, which helps keep chassis servicing focused on the exact section rather than replacing unrelated hardware. Visible components include upright body posts with a series of adjustment holes, shaped brackets, reinforcing plates and small spacers. That layout supports precise positioning where shell height or mounting alignment needs to match an existing setup on a TA-05 or TB Evo.IV platform. This kind of parts set suits workshop stock for routine RC upkeep, accident repair or the completion of an unfinished chassis section. It can be used when restoring the original mounting arrangement after wear, damage or missing hardware, and it keeps the fit of the shell support area tied to the intended B-parts group for these model platforms.  Warning! Not suitable for children under 14 years.

Gears & motor pinions

TA-05/TB-03 Drive Shaft, metal spare part, 45 mm

€11.99

The TA-05/TB-03 Drive Shaft 45 mm is a metal spare part for compatible Tamiya chassis setups, with 2 matching shafts supplied for drivetrain service on FF-03 chassis, FF-03 PRO chassis, TA05 Ver.II and TA05. The 45 mm length gives a clear fit reference when a build or repair calls for this exact shaft size. Each shaft uses a straight rod form with ball ends and cross pins, a layout designed to connect with the surrounding drivetrain hardware in the intended mounting points. The metal construction and polished finish give the part a clean technical look while keeping the focus on mechanical function inside the chassis. As a dedicated replacement component, it suits maintenance work, parts refreshes and like-for-like swaps where the named platforms require this specific format. In workshop use, the 2-piece set supports planned servicing or the replacement of worn drivetrain hardware on one of the listed chassis types. Kept alongside other RC spares, the clearly stated compatibility and 45 mm dimension make this part easy to identify before installation.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

TA-05IFS D-Parts, RC chassis suspension arms

€10.99

TA-05IFS D-Parts is an RC chassis spare parts set with 4 molded suspension arms arranged as 2 front and 2 rear pieces. The wishbone-style shape, mounting holes and central attachment points support correct installation on compatible touring car platforms and restore the intended suspension layout after wear or impact damage. The scope of delivery contains 1x D parts tree with 4 parts. These black molded components are intended for replacement and maintenance work rather than universal use, so the value lies in exact fit across the listed chassis families. Compatibility covers FF-03, FF-03 PRO, TA06 MS, TA06, TA06 PRO, TA05 ver.II, TB-Evo.7, TB-Evo.6 MS, TB-Evo.6, TB-05 PRO, TB-04, TB-04 PRO, TB-03, TB-03 VDS, TRF419XR, TRF419X, TRF419, TT-02 TYPE-SR and TT-02 TYPE-S. That broad fit list makes the set useful in a spares box for racers and builders maintaining more than one platform. During workshop servicing, replacement arms like these help return free suspension travel and proper linkage alignment on the compatible chassis. They also suit planned rebuilds where fresh running gear parts are fitted before the next track session.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

TA-05IFS/TB-03 F-Parts Hub Carrier (2), chassis part

€7.79

The TA-05IFS/TB-03 F-Parts Hub Carrier set supplies 2 matching chassis components for RC model maintenance, rebuilds and parts replacement. Shaped as front F parts, these pieces are intended for the front area of compatible on-road platforms, where correct mounting points and part geometry matter for a clean fit during service work. Compatibility covers a wide range of Tamiya chassis: FF-04 EVO, FF-03, FF-03 PRO, TA06 MS, TA06, TA06 PRO, TA05 Ver.II, TB-Evo.6 MS, TB-Evo.6, TB-05 PRO, TB-04, TB-04 PRO, TB-03, TB-03 VDS and TT-02 TYP-S. The scope of delivery contains 1 F parts set with 2 components. That broad fitment makes the set useful as a replacement kept alongside regularly used touring car spares, especially when one workshop supports several chassis generations. During routine maintenance, crash repair or a full chassis refresh, a matched pair helps restore the intended front assembly with the correct left and right quantity already in the pack. The black molded parts shown for this set focus attention on fit and function rather than decoration, making them a straightforward choice for keeping compatible RC chassis ready for the next build session or track run.  Warning! Not suitable for children under 14 years.

Gears & motor pinions

TA-06 Rear Gear Diff. Case Set 52T Spare Part

€4.79

The TA-06 Rear Gear Diff. Case Set 52T is a dedicated spare part for compatible Tamiya chassis, built around a rear bevel gear differential housing layout that supports accurate servicing of the drivetrain. With 7 pieces in the set, it provides the core parts needed for replacing the rear diff case assembly when wear, damage or a rebuild calls for fresh components. This set is specified for TA06, TA06 PRO, TA06 MS, XV-01, XV-01 PRO, XV-01T, M-07 CONCEPT, M-08 CONCEPT and FF-04 EVO chassis. It also fits TD4 and TD2 chassis when used with 54471, which makes the compatibility scope especially useful for hobby benches handling several platforms. The black moulded parts shown for the assembly use multiple fastening points and a separate cover section, supporting a clean mechanical fit around the differential area. On a maintenance bench, the set helps restore a worn rear transmission section with chassis-specific parts instead of improvised substitutes. During a rebuild, the 52T case format and rear mounting design support a focused replacement job for the differential housing section while keeping the chassis setup aligned with the listed applications.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

TA02 D-Parts Suspension Arms, RC spare parts

€18.79

TA02 D-Parts Suspension Arms bring core running gear pieces together in one replacement set for RC chassis maintenance. The black molded sprues show mirrored suspension components, linkage-style parts and smaller inserts, giving a clear starting point when worn or broken originals need to be swapped out. The sprue layout keeps related shapes organised before removal, which helps when matching left and right side parts during a repair. Large A-arm style pieces sit alongside long narrow bars with multiple mounting points, plus smaller lever-like forms and circular bush-style elements. This mix supports detailed work on suspension-related areas rather than general cosmetic changes. The molded numbering on the runners also helps identify individual sections during parts preparation and fitment. On the bench, this set suits routine chassis upkeep, restoration of older TA02-based builds and replacement after hard running sessions. It also works as a practical spare to keep in a workshop drawer, ready for rebuilds that call for original-style suspension hardware and linked structural pieces.

Gears & motor pinions

TA05 IFS Ver.II Spur Gear, RC spare part, 70T M0.6

€6.29

The TA05 IFS Ver.II Spur Gear is a dedicated RC spare part for drivetrain service on selected Tamiya chassis. With 70 teeth and module 0.6, this main gear is built for transmission use where the gear ratio and tooth format must match the existing layout, making it a focused choice for repair or planned parts replacement. The component is supplied as 1 main gear 70T and is shown as a black molded gear with a fine outer tooth ring, a large center hole and multiple evenly spaced inner holes. That geometry matters during maintenance because the mounting pattern and hub area have to align with the drivetrain hardware already in the chassis. Compatibility is stated for TD4 chassis, TD2 chassis, TA08 PRO chassis, TA05 Ver.II chassis and TA05, which keeps selection tied to named platforms rather than broad guesswork. On the bench, this gear suits routine transmission refreshes, rebuilds after wear, or a direct swap when a matching 70T M0.6 part is needed for one of the listed chassis. The single-part scope also keeps the replacement straightforward when an existing drivetrain setup is being restored with the same specification rather than changed to a different ratio.  Warning! Not suitable for children under 14 years.

Gears & motor pinions

TA08 06 Module Spur Gear 71T, RC spare gear

€3.69

The TA08 06 Module Spur Gear 71T is a drivetrain spare part for TA08 chassis cars, built to replace a worn gear with the same 06 module format and 71T tooth count. In the transmission, the spur gear works directly with the pinion gear to pass motor power into the driveline, so a fresh gear can restore clean meshing where wear has built up over time. The part shown has a black moulded finish, a large centre hole and multiple circular cut-outs around the hub. Those openings are part of the gear design and sit around the central mounting area while the fine outer teeth carry the load of the gear mesh. Used as routine maintenance, this replacement helps keep the chassis in running condition when the original gear shows visible wear on the teeth. The pack contains 1 TA08 06 Module Spur Gear 71T. It suits workshop upkeep between running sessions, whether the transmission is being refreshed after repeated use or a worn gear is being swapped before the next outing. For TA08 owners who keep spares on hand, this gear covers a core wear point in the drivetrain with the exact compatibility stated for TA08 chassis cars.

Axes & drive shafts

TA08 A Parts Steering Arm Pully RC Spare Set

€14.49

TA08 A Parts Steering Arm Pully 58693 is a replacement parts sprue for RC model maintenance, centred on steering arm and pulley components that restore key chassis functions on the intended TA08 build. The black moulded frame presents the parts in a clearly organised layout, with each piece held in place until needed at the workbench. The runner carries a mix of larger structural shapes and smaller fitting pieces, including arm forms, ring elements and compact mounting details that belong together within the same assembly area. Moulded reference marks with the letter A and numbers 1 through 14 are visible on the sprue, giving a direct visual guide when matching each section to the required build step or service task. This format helps separate similar-looking pieces before cutting and supports a tidier repair process when a worn section needs replacement rather than a full rebuild. On a maintenance bench, the grouped layout makes it easier to prepare the required sections before installation and keep unused pieces together until later service work. For ongoing chassis care, a dedicated replacement frame like this helps return the matching model to proper mechanical condition with the correct part shapes kept in one set.

Other spare parts & accessories

TA08 BB Parts Body Mount Bumper Spare Set

€14.99

The TA08 BB Parts Body mount/bumper set provides replacement components for the TA08 platform where the body mounting area and bumper section need to be renewed. Supplied as molded black parts on a sprue, the set focuses on the shaped pieces that connect through formed holes, tabs and attachment points within the chassis assembly. The sprue layout keeps each section identifiable before removal, with the larger curved panel, narrower perforated strips and link-style piece grouped in one frame. This format helps during workshop preparation because each molded section stays in place until trimming begins. Visible part markings on the frame support orientation while matching the pieces to the intended build location. As a spare-parts set rather than a complete kit, the emphasis stays on replacing worn or damaged sections with the correct TA08 BB Parts shapes. On the bench, this set fits naturally into routine maintenance, accident repair or a planned rebuild of a used chassis. It can be kept alongside other running spares so the front structure and body support area are ready to restore when a damaged section needs to be swapped out.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

TA08 D Parts Suspension Arms for TA08 Chassis

€13.49

TA08 D Parts suspension arms are replacement chassis components for TA08 cars, supplied as 2 parts for maintenance when existing arms are worn. The set focuses on a key suspension area, making it useful for restoring the chassis with matching parts intended for the named platform. The molded parts shown in the set use a mirrored left and right layout, with multiple pivot points and mounting positions formed into each arm. This geometry matters in an RC chassis because the suspension arms connect the wheel assembly to the main structure and guide movement through compression and rebound. Metal-lined pivot holes are visible in the image, adding defined contact points where the parts mount into the suspension system. The black finish keeps the look consistent with typical chassis hardware and makes the parts easy to integrate into an existing TA08 build. These parts suit routine workshop maintenance, rebuilds after heavy running, or a fresh chassis refresh before the next session. In a repair setup, the 2-piece format supports replacing worn arm sections as a matched pair so the suspension layout stays even across the car.

Gears & motor pinions

TA08 Front Belt 132T, RC spare part for chassis

€12.19

The TA08 Front Belt 132T is a dedicated replacement part for compatible TA08 chassis cars, built to restore the front drivetrain with the specified tooth count and matching belt format. Its black toothed loop is shaped to run around the front transmission pulleys, where it transfers motion through the drivetrain and helps return a worn setup to its intended mechanical operation. As a service part, this belt is focused on fit and function rather than cosmetic change. The 132-tooth layout is the defining specification for this component, making it relevant when an existing belt shows wear through repeated running or maintenance inspection. The thin, flexible construction allows the belt to sit correctly within the chassis transmission path, while the toothed inner profile is made to mesh with the matching pulley system used in the TA08 platform. This replacement suits regular workshop upkeep, planned drivetrain refreshes and repair after belt wear has affected running consistency. Kept as a spare for a TA08 chassis car, it supports faster maintenance decisions when the front drive system needs the correct belt specification rather than a universal substitute.

Gears & motor pinions

TA08 Rear Belt 101T, chassis spare part

€9.19

The TA08 Rear Belt 101T is a dedicated spare part for TA08 chassis cars, built to replace the rear transmission belt when wear starts to affect the drive system. Its toothed inner surface is designed to engage with matching pulleys, creating the mechanical link that carries rotational force through the rear section of the chassis. Used as part of routine maintenance, this replacement belt helps preserve the intended drivetrain function of a TA08 setup. The circular flexible belt format allows it to sit correctly around the pulley path, while the 101T specification identifies the exact rear belt version supplied here. The pack contains 1 rear belt, making it a direct service part rather than a multi-piece upgrade set. Because this is a chassis-specific component, compatibility is stated for TA08 chassis cars. In workshop use, a fresh rear belt is fitted when an existing belt has become worn through repeated running. That makes this part a practical choice for keeping a TA08 car ready for further track sessions, tuning work, and regular upkeep of the transmission system.

Shock absorbers & springs

TAMIYA Silicone Oil #400, damper oil, 40 ml

€8.191 l = €204.75

TAMIYA Silicone Oil #400 is a 40 ml damper oil for model vehicles, made to tune the feel of oil-filled dampers with a simple viscosity change. The #400 grade sits in the firmer range, since higher numbers indicate a harder viscosity, making it a practical choice when suspension setup needs a more controlled response. The bottle uses a narrow dispensing tip that supports careful, drop-by-drop application when filling shock bodies on the workbench. Its larger 40 ml content is aimed at frequent users and offers more oil than the earlier 35 ml and 20 ml bottles referenced in previous sets. Each viscosity grade in the range has its own color coding, which helps keep different oils clearly sorted in a toolbox during maintenance sessions. The supplied safety data identifies the mixture as organopolysiloxanes and lists its intended use as damper oil for model vehicles. On a setup bench, Silicone Oil #400 fits routine shock servicing, viscosity swaps between runs, and fine suspension adjustment when track conditions or handling balance call for a firmer damper fill. It also suits keeping several grades organized side by side, so the selected oil can be identified quickly before the next rebuild or test session.

Other spare parts & accessories

Tamiya Tweezers Straight, precision craft tool

€10.49

Tamiya Tweezers straight bring precise control to detailed model work, with a straight stainless steel body and fine pointed tips that help place small parts exactly where they belong. The slim profile suits close-up tasks at the bench, where careful alignment and a clear view of the work area matter. The pointed ends support delicate handling during assembly, touch-up work and other precision jobs that call for exact placement rather than finger pressure. Stainless steel gives the tool a clean, rigid structure for repeat use, while the black cationic finish adds a durable surface treatment to the long, narrow body. The straight form keeps the handling direct and predictable, which helps when guiding tiny components into narrow gaps or adjusting their position by small increments. On a model bench, these tweezers suit jobs such as setting fine details, moving small pieces into place and handling parts that are difficult to grip by hand. They also fit other craft tasks where accuracy, visibility and a light touch are needed around delicate components.

Gears & motor pinions

TB-03/TT-02SG Spur Gear, RC spare part, 64T

€5.69

The TB-03/TT-02SG Spur Gear 64T M0.6 is an RC spare part built for drivetrain service, replacement and gearing maintenance on compatible chassis. With 64 teeth and module 0.6, it forms the main gear interface that transfers drive through the transmission, making it a concrete choice when an existing setup needs the same specification again. This gear is supplied as 1 main gear and is intended for use with TT-02 chassis, TT-02D chassis, TT-02 TYPE-S chassis and TT-02 TYPE-SR chassis. It can also be used on vehicles equipped with 54500. For TT-02RR chassis, the 64T gear is standard kit equipment, which helps when matching the original drivetrain specification during routine parts replacement. The visible central mounting hole and surrounding fixing points suit its role as a mounted transmission component rather than a general workshop accessory. In workshop use, a like-for-like 64T replacement keeps a compatible chassis aligned with its intended gearing layout after wear or damage. It also suits RC model maintenance benches where specific tooth counts and module sizes matter for keeping transmission parts consistent across different compatible builds.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

TB-03D N-Parts Control Arm Mount, chassis parts

€4.59

The TB-03D N-Parts Control Arm Mount set provides a focused replacement solution for suspension-related service on the TB-03D chassis. With 6 control arm mounts in the set, it covers a key hard-point area where accurate part matching matters during maintenance, rebuilds and chassis refresh work. The data identifies these as N-Parts and links them directly to the TB-03D platform, which helps keep part selection aligned with the intended chassis layout. Control arm mounts sit at a critical connection point in the suspension system, so using the specified part group supports a clean restoration of the original mounting arrangement. The fit reference also extends to the 300047524 1:10 Porsche 934 50th Anniversary model, giving an additional compatibility route where that exact model is being serviced. This is a chassis-parts set rather than a mixed bundle, so the contents stay concentrated on one mechanical area. On the bench, that makes the set useful for replacing missing mounts, refreshing a used drift chassis, or keeping matching spares ready between running sessions. The 6-piece count also suits planned maintenance where several mounting points are checked and renewed together.

Gears & motor pinions

TB-04 One-way/Gear Dif. Ring Gear Set 40T

€7.39

The TB-04 One-way/Gear Dif. Ring Gear Set 40T is a drivetrain spare part for selected RC chassis, built around a 40-tooth ring gear and matching bevel components for freewheel or gear differential use. Its dedicated fitment keeps maintenance work focused on the transmission systems named for this set. The set contains 1 bevel gear set with 3 parts. The large ring gear uses a circular form with evenly cut teeth around the outer edge, while the smaller matching gears complete the assembly for the stated drivetrain function. This makes the set suitable for replacing worn internal transmission parts or preparing a compatible chassis for differential or one-way service work. Compatibility is stated for TB-Evo.7 chassis, TB-Evo.6 MS chassis, TB-Evo.6 chassis, TB-05 PRO chassis, TB-04 chassis, TB-04 PRO chassis and TC-01 chassis. In workshop use, the set supports targeted repairs on the named platforms rather than broad universal fitment. The 40T specification gives a clear reference point when matching replacement drivetrain parts during servicing, rebuilds or planned maintenance on compatible RC car chassis.  Warning! Not suitable for children under 14 years.

Gears & motor pinions

TB-05 06 Module Spur Gear 63T, spare gear

€3.89

The TB-05 06 Module Spur Gear 63T is the direct spare gear for the TB-05 chassis, built to return the drivetrain to the original kit specification with a 63-tooth layout and 06 module tooth form. As an OEM replacement, it is intended for the same transmission position as the stock part, so the gear train can be restored with the correct meshing profile and ratio. The moulded gear uses fine outer teeth around the full circumference to transfer rotational force through the drivetrain, while the large centre bore locates the part on its mounting point. The inner web includes multiple moulded support sections and cutouts that shape the gear body around the hub area. This is a single replacement component rather than a conversion part, making it suitable when the original spur gear is worn or when the stock specification is needed again. The tooth pitch is optimised for use with common gear ratios, as stated in the product data. In workshop use, this spare gear suits routine drivetrain maintenance on a TB-05 chassis or a rebuild that returns the transmission to the original kit setup. It can also serve as a like-for-like replacement to keep a running chassis aligned with the factory gear specification.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

TC-01 C/D-Parts Suspension, chassis spare parts

€12.79

The TC-01 C/D-Parts Suspension set is a dedicated spare parts pack for TC-01 chassis cars, built around 2 C/D parts trees that support accurate maintenance of the suspension system. With molded replacement pieces for key chassis assemblies, it helps restore clean fit and consistent movement where the running gear works hardest. Within the set are suspension arm, knuckle and rocker arm components, grouped as useful service spares for the TC-01 platform. These parts sit in areas that guide wheel movement, support steering articulation and connect suspension elements across the chassis layout. Using model-specific replacement parts keeps mounting points, pivot locations and part geometry aligned with the original TC-01 design. The black molded finish also matches the technical look commonly used across RC chassis assemblies. This set suits workshop maintenance, rebuilds after heavy running sessions, or keeping a spare pack ready for future repairs on a TC-01 car. It can be used when refreshing worn assemblies, replacing damaged pieces after contact, or rebuilding one side with matching counterpart parts from the same set.

Other spare parts & accessories

TC-01/TA-07 Carbon Crossmember Rear RC Part

€15.79

The TC-01/TA-07 Carbon Crossmember Rear adds a focused chassis upgrade to compatible RC touring car builds. Its 2 mm carbon fiber construction spans the left and right rear body mounts, creating a firmer connection that cuts body wobble and gives the rear mounting area a more settled feel during running sessions. The part is supplied with snap pins and 5 mm O-rings for installation at the body mount points. The O-rings are used to cure looseness, helping the mounted shell sit with less play at the connection. A choice of 3 body mount positions adds useful setup flexibility when adjusting shell placement on the chassis. The instruction notes also specify that the crossmember should not contact the body itself, and that instant cement is sold separately for edge treatment. This rear crossmember suits builders refining body mount stability on compatible TC-01 and TA-07 layouts. It works as a compact tuning part for garage setup, shell fitting and track preparation, especially where a more rigid rear mount connection is preferred.

Shock absorbers & springs

TD2/TD4 Alum. BigBore Rear Damper, RC parts set

€88.99

The TD2/TD4 Alum. BigBore Rear Damper set brings a larger aluminum oil damper layout to the rear suspension, with 2 dampers built around threaded bodies, 40.7 mm piston rods and a full set of internal sealing parts. During assembly, the piston is filled with damper oil and moved slowly through the cylinder to release trapped air, giving the aeration design its working basis before the cap is secured. Inside each damper, the build uses O-rings in 2 mm, 3 mm, 6.5 mm, 11.5 mm and 14 mm sizes, plus 4 x 0.1 mm and 3 x 0.2 mm shims to support sealing and internal spacing. Two piston types are provided, with 1.6 mm and 1.7 mm holes, so the oil flow setup can be chosen during the build rather than fixed to one specification. Spacers are used to adjust rebound stroke and damper attachment position, adding another layer of chassis setup detail. Spring retainers and spring adjusters complete the upper section, while screws in 3 x 18 mm, 3 x 15 mm and 3 x 12 mm sizes support mounting. On the bench, this set suits careful suspension rebuilding, oil filling and setup changes between running sessions. Damper oil and coil springs are separately available, and the assembled dampers are intended for TD2 and TD4 rear suspension use.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

TD4 Universal Shaft Set, RC drivetrain parts

€33.99

The TD4 Universal Shaft Set brings a focused drivetrain upgrade or replacement to RC model maintenance, centered on 2 assembled universal shafts and the matching wheel-end hardware. Black-coated metal construction and the articulated joint layout support power transfer where rotating parts need to keep working through steering input and suspension travel. Each shaft is marked 73 and uses a looped eye at one end with a ball end at the other, a mechanical arrangement suited to angled driveline connections rather than a fixed straight link. Alongside the shafts, the set provides 2 axle or outdrive-style components with threaded sections and cross-holes, plus retaining rings, straight pins and 2 short cylindrical couplers. That combination gives the assembly the small locking and joining parts required for a complete drivetrain fitment around the shaft connection points. On the bench, this set suits repair work after wear in the driveline or a planned parts refresh during a chassis rebuild. The compact hardware selection also helps keep RC maintenance organised, with the matching metal pieces grouped for one shaft-related installation rather than drawn from mixed spare parts.

Other spare parts & accessories

Tire Cementing Helper, RC tire gluing tool

€25.49

The Tire Cementing Helper is a dedicated RC workshop tool for bonding tires to wheels with more control at the rim edge. The mounted tire and wheel are placed on the adapter, then light pressure opens a narrow gap between both parts so the cement can flow more easily into the joint. That simple mechanical action helps guide adhesive exactly where the bond is needed during on-road wheel preparation. The set is supplied with an additional adapter for M-chassis use, so it works not only with touring car wheels but also with small diameter M-chassis tires. This makes the tool useful across 2 common RC car wheel formats without changing the basic handling method. The shape is focused on the contact area between rubber tire and wheel rim, where even cement distribution matters most. The tool is intended for manual use during the tire mounting process and supports a steadier workflow when preparing multiple wheel sets. On the bench, the helper suits careful adhesive application before running or display preparation. It can be used when fitting fresh rubber tires, reworking wheel sets, or setting up M-chassis and touring car wheels with a cleaner, more deliberate bonding step.  Warning! Not suitable for children under 14 years.

Gears & motor pinions

TL-01 G-Parts Gear Set, chassis spare parts

€12.29

The TL-01 G-Parts Gear Set is a dedicated spare parts pack for the TL-01 chassis, built around the transmission components used in this platform. With 10 pieces in the set, it provides a focused way to replace worn gearbox parts, refresh a running chassis, or support a rebuild with matching molded elements. The scope of delivery includes 1x G-Parts set with 10 pieces. The visible component group covers several gear forms used in drivetrain layouts, including larger spur-style gears, smaller geared parts and round cover-like elements shaped for gearbox assembly. These molded parts are intended for power transfer inside the chassis transmission, where the gear train routes motor output through meshing teeth and mounted shafts. Using a chassis-specific set helps keep fit and function aligned with the TL-01 layout instead of relying on mixed generic parts. On the bench, this set fits routine service, fault tracing after drivetrain wear, or a planned refresh of an older TL-01 build. It also works well as a workshop spare kept alongside other chassis-specific parts, ready when gearbox maintenance calls for the correct G-Parts group.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

TL-01 Upright C-Holder Set, chassis spare parts

€10.79

This TL-01 B-Teile Achsschenkel/C-Halter set is a dedicated spare parts pack for the TL-01 chassis, supplying the molded components needed when key mounting points on the running gear need replacement. The scope of delivery includes 1x B parts group with 21 pieces, arranged as a matched set for chassis service and rebuild work. The molded black components include upright and C-holder forms together with related small fittings from the same parts section, so the replacement pieces come from one coordinated runner group. Image details show mirrored left and right parts, circular bearing housings, pivot points, hex-shaped hub-style pieces and marked small levers, all indicating precise placement within the chassis assembly. This makes the set useful for restoring worn or damaged areas while keeping the fit consistent with the original TL-01 layout. On the workbench, the set supports routine maintenance, targeted repairs after running sessions or the refresh of an older chassis build. Kept as workshop stock, these chassis-specific parts help avoid mixing incompatible components and make it easier to return a TL-01 model to proper mechanical condition.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

TL01 C-Parts Suspension Arm Body Mount Set

€21.29

This spare parts set is made for the TL01 chassis and brings together C-Parts for suspension arm and body mount functions in one matching pack. With 2x C parts and 52 pieces in the scope of delivery, it supports maintenance work that calls for the correct molded shapes rather than improvised substitutes. The set is suited to rebuilds, repairs and parts replacement on an existing compatible chassis. Suspension arm sections and body mount components sit among the parts group, allowing worn, damaged or missing sections to be exchanged while keeping the intended chassis structure. The molded black finish matches the technical look typically used for RC chassis components and makes the different shapes easy to sort during workshop preparation. Because the parts come as a dedicated C-Parts set, the pack stays focused on the exact component family needed for this area of the build. On the bench, this set fits naturally into routine servicing after heavy running sessions, collision damage or long-term wear on a TL01 model. It also helps when restoring an older chassis that needs original-style replacement parts to return mounting points and suspension connections to working order.  Warning! Not suitable for children under 14 years.

Gears & motor pinions

TL01 Speed-Tuned Gear Set, RC gearbox upgrade

€14.99

The TL01 Speed-Tuned Gear Set changes the character of a TL-01 drivetrain with a replacement 47T spur gear and 29T counter gear. Installed in place of the normal transmission gears, this hop-up option shifts the final drive toward higher speed and gives the chassis a sharper, faster-running setup on the track. The ratio change is clearly defined across 3 pinion choices. With a 19T pinion, the ratio moves from 7.96 to 5.95; with 21T, from 7.20 to 5.39; and with 23T, from 6.57 to 4.92. The technical guide also shows grease application points during assembly, helping the gear teeth mesh correctly inside the gearbox case. Bearings and a hollow carbon gear shaft are shown as available separately, and their use is noted for reducing burden on the motor during running. Scope of delivery: 1x Speed Gear. This upgrade suits TL-01 builds that are being tuned beyond the standard transmission layout. In workshop use, the gear swap gives builders a direct mechanical change to experiment with, while on-road running highlights the effect through a more speed-oriented drive setup.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

TL01 Stainless Steel Suspension Shaft Set

€9.59

The TL01 Stainless Steel Suspension Shaft Set is a hop-up hardware set for TL01 chassis models, built around 8 grooved stainless steel shafts and 16 matching 2 mm E-rings. The shaft layout follows the replacement guide shown for the chassis, with 4 shafts at 3 x 48.5 mm and 4 at 3 x 37 mm, giving the suspension mounting points the specified metal parts for service or upgrade work. The grooved shaft ends are designed to accept the included E-rings, which snap into place to retain each shaft after installation through the relevant suspension points. The guide identifies these shafts as replacements for 3 x 46 mm and 3 x 32 mm screw pins, changing the fixing method from threaded pins to retained shafts with clips. That layout is useful when refreshing a used chassis, replacing missing hardware or preparing a TL01 build with the correct hop-up parts. The set focuses on the pivot hardware itself rather than cosmetic changes, making it a functional addition for maintenance benches and parts boxes. During assembly or repair, the two shaft lengths help match the correct front or rear mounting positions shown in the fitting diagram. The compact metal parts format also makes the set easy to store alongside other chassis spares for routine rebuilds and running upkeep.

Shock absorbers & springs

Touring Car Bumper Sponge, RC accessory, grey

€5.79

This touring car bumper sponge is a grey urethane block sized at 70 x 225 x 25 mm, made to be trimmed into a custom front bumper for RC chassis. The soft material is intended to absorb shocks from contact and falls, helping protect the body shell and chassis when the front end takes an impact. Instead of using a fixed shape, the block can be cut to suit the body mounted on the car. That makes it possible to match the bumper more closely to the shell profile and use the available space at the nose section more effectively. The universal fit information covers a broad list of compatible chassis, including F103GT, FF-04 EVO, FF-03, FF-03 PRO, TA08 PRO, TA07 MS, TA07 PRO, TA06 MS, TA06, TA06 PRO, TA05 Ver.II, TB-Evo.7, TB-Evo.6 MS, TB-Evo.6, TB-05 PRO, TB-04, TB-04 PRO, TB-03, TB-03 VDS, TRF419XR, TRF419X and TRF419. In workshop use, the sponge can be shaped for a new shell, a replacement body or a revised race setup where front-end clearance matters. The rectangular format also leaves room to remove only as much material as the body line requires, rather than working around a pre-formed bumper shape.  Warning! Not suitable for children under 14 years.

Gears & motor pinions

TRF 1050 Bearing Thick 3mm, ball bearings

€4.89

The TRF 1050 Bearing Thick 3mm is a focused tuning and replacement part for touring car chassis that use a reversible suspension system with Double-Cardan drive shafts. Each bearing measures 5 x 10 mm with a 3 mm width, and the set contains 2 ball bearings for the positions that need this narrower format. Its key difference is the reduced width compared with the usual 5 x 10 x 4 mm bearing used in these layouts. That 1 mm change gives the Double-Cardan swing shaft more running clearance at the inside of the hub carrier, which is the exact area named for installation. This makes the bearing useful when a chassis setup calls for extra space around the shaft rather than the standard bearing thickness. The pair is intended only for the front or rear inside portion of the hub carrier, keeping the application specific and technically clear. Compatibility information covers numerous chassis families, including TA07 MS, TA06 MS, FF-04 EVO, TB-Evo.6, TB-Evo.7, TC-01, TRF419, TRF419X, TRF419XR, TT-02 TYPE-SR, TA07 PRO, TA08 PRO, FF-03, TB-03, TB-04, MF-01X, M-05, M-06, M-07 CONCEPT, M-08 CONCEPT, TT-02 TYPE-S and TRF420X, with some applications requiring specified companion parts.

Other spare parts & accessories

TRF 1510 Sealed Ball Bearings, model accessory

€9.79

TRF 1510 Sealed Ball Bearings add a focused drivetrain upgrade to compatible model assemblies by combining smooth rotation with a serviceable sealed design. The 2 included bearings use rubber seals and low-friction oil inside, creating a compact replacement part that supports clean running in areas where drag and fit directly affect how rotating parts behave. The 1510 format is suited to applications such as touring car bulkheads and M-chassis car differentials, where accurate seating and controlled movement are essential. Rubber seals set these bearings apart from metal-sealed versions because they can be opened for cleaning and maintenance. That makes it easier to remove dirt, refresh lubrication and return the bearing to use without replacing the whole unit. In place of plastic and metal bearings, this design improves parts fit and promotes more efficient rotation in compatible assemblies. On the workbench, these bearings suit routine servicing, drivetrain refreshes and targeted upgrades to worn running gear. In a differential or bulkhead setup, the combination of precise attachment and internal low-friction lubrication supports smoother mechanical action across repeated running sessions.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

TRF 730 Sealed Ball Bearings, model accessory

€8.79

The TRF 730 Sealed Ball Bearings set supplies 2 replacement bearings for compatible model assemblies where smooth, controlled rotation matters. The sealed construction is the defining feature here, because it helps shield the internal rolling elements from dirt while the bearing supports turning shafts or axles inside a compact mechanical layout. This set is focused on maintenance and running efficiency rather than decoration. In workshop use, the 730 bearing size gives a clear specification to match against the required location in a chassis, gearbox or other rotating assembly that takes this format. Fresh bearings can restore cleaner movement in parts that have seen repeated use, and the sealed design is especially useful in areas where dust and fine debris can work into moving components. The 2-piece quantity also suits replacing a pair at the same time when a matching assembly uses 2 bearings together. On the bench, this bearing set fits naturally into routine service, rebuilds and parts planning for RC and scale models. It can be kept as a spare for future repairs or installed during a targeted refresh of compatible running gear, helping mechanical systems turn with less resistance and more consistency.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

TRF Alum. Wheel Spacer, model accessory, 0.75 mm

€8.29

The TRF Alum. Wheel Spacer 0.75 mm Blue is a tuning accessory for touring car R/C models that focuses on one small dimension with a clear setup effect. By adding a 0.75 mm spacer at the wheel mounting point, the tread can be adjusted with more precision, making it easier to refine how the chassis sits across the axle line during setup work. The set contains 8 aluminum spacers in blue, giving a consistent group of matching parts for workshop use, replacement needs or side to side setup changes. Aluminum construction adds rigidity at this contact area, which matters when small measurements are used to influence chassis balance. Rather than changing a major component, this spacer works through a controlled adjustment of wheel position, making it a useful choice when fine tuning a touring car model for a more exact tread setting. On the bench, these spacers fit naturally into routine maintenance and setup sessions for compatible touring car R/C models. They suit builders who compare different chassis responses through measured hardware changes and want a simple way to repeat the same spacing on multiple wheel positions.  Warning! Not suitable for children under 14 years.

Shock absorbers & springs

TRF Damper Urethane Bushings, RC Damper Parts

€4.79

The TRF Damper Urethane Bush set supplies 10 replacement bushings for servicing compatible TRF dampers. Used as oil seals, these urethane parts help keep the damper sealed correctly so suspension action stays consistent and maintenance can be carried out before visible wear affects performance. The set is intended for TRF dampers with fluorine coating specification and supports regular rebuild work on a wide range of chassis. Compatibility includes XV-01, XV-01T, XV-01 PRO, TB-03, TT-02, TT-02D, TT-02 TYPE-S, TT-02 TYPE-SR, TT-01 TYPE-E, TT-01D TYPE-E, TT-02RR and TT-02FT when used with 53571. It also fits M-07 CONCEPT chassis when used with 42102, 42273, 42355 or 54000. The scope of delivery contains 10 urethane bushings. In workshop use, fresh seals can be fitted during damper maintenance to restore the intended sealing function and keep the suspension ready for further track sessions. The compact pack format also makes it easy to keep matching service parts on hand for planned rebuilds or routine upkeep across compatible chassis.  Warning! Not suitable for children under 14 years.

Shock absorbers & springs

TRF Dampers Reinforced V Parts, damper upgrade set

€8.19

Reinforced V Parts for TRF Dampers update the standard mounting and spring support pieces with redesigned shapes and material, opening up more setup options for suspension tuning. The set is built around TRF damper maintenance and adjustment, so worn parts can be replaced while the damper layout is matched more closely to the chassis setup in use. Inside the set are 5 mm damper ends in S and M, 5.8 mm damper ends in S and M, 5 mm damper tops, 5.8 mm damper tops, and spring retainers in S and M. The instruction data notes that parts are chosen according to damper length, and one spring retainer version is specified for large diameter springs. One step requires a 1 mm hole as shown in the technical diagram, and the ball connector is pressed in from the indicated side on the relevant parts. For use with V2, V3 and V7, separately sold dedicated 5.8 mm damper ball connector nuts and a cylinder cap are required. This set suits routine damper overhauls, chassis retuning between runs, and replacing standard TRF damper parts with reinforced alternatives. It is compatible with TRF Dampers such as Items 53571, 53901 and 54000 when used with Item 53334, making it a focused upgrade for established TRF suspension setups.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

TRF Drive Shaft 42mm W Cardan, RC spare part

€20.99

The TRF Drive Shaft 42mm W Cardan is a drivetrain upgrade part shaped for front-end use on Tamiya touring cars, where the Double Cardan layout helps cut rotational vibration and gives the steering a cleaner, more settled feel through direction changes. Each shaft uses 2 joint sections, a configuration aimed at smoother power transfer in a part of the chassis where precision is easy to notice. This set contains 2 shafts and is based on the 44 mm Double Cardan Joint Shaft from Item 42216, but with each shaft shortened by 2 mm. That change brings the overall length in line with a standard 42 mm universal drive shaft while leaving more room for suspension setup changes. The result is a tuning part that supports finer adjustment of front suspension geometry without moving away from the familiar 42 mm fit. The dark mechanical finish and compact joint housings match the technical look of competition-focused RC running gear. Installed on the front end of a touring car chassis, these shafts suit builds where steering response, corner entry feel and setup flexibility matter during track tuning. They also work well as replacement drivetrain parts when a front assembly is being refreshed with matching left and right components.

Screws & ball head screws

TRF M4 Serrated Wheel Nuts, RC accessory, blue

€8.49

These TRF M4 serrated wheel nuts add a focused hardware upgrade to an R/C setup, combining blue anodized aluminum with a serrated contact face that is designed to improve wheel grip at the mounting point. The result is a firmer wheel attachment that suits faster running and repeated laps where hardware security matters. The 4 mm M4 specification gives a clear reference for compatible wheel hardware, and the set of 4 pieces covers a full vehicle. The serration works through direct contact at the wheel mount rather than through added bulk, so the change stays compact while addressing a critical fastening point. The aluminum construction keeps the hardware light, and the blue anodized finish makes the nuts easy to identify during bench work, wheel changes and routine checks between runs. On a home workbench, in a pit area or before a club session, this set fits naturally into regular maintenance stock. It suits replacing worn wheel hardware, refreshing a build with matching fasteners, or preparing an R/C chassis for more demanding track use where consistent wheel retention is a priority.

Other spare parts & accessories

TRF O-Rings 40° Gear-Diff., touring car parts

€6.49

TRF O-Rings 40° Gear-Diff. are dedicated replacement parts for touring car oil-filled gear differentials. The set contains 4 blue ring-shaped O-Rings, arranged for direct use in differential service where this specific 40° specification is required. Their dedicated gear differential design focuses on minimal friction inside compatible oil-filled differential assemblies. In practice, that means the differential can work with less internal drag while transmitting drive through the drivetrain. The ring shape and smooth surface suit sealing and moving contact points inside the differential layout used on compatible touring car models. This is a targeted maintenance part rather than a universal ring set, so the stated compatibility with oil-filled gear differentials is the key fit detail. During workshop maintenance, the 4-piece pack supports a planned differential refresh or replacement of worn rings in an existing setup. The compact format also makes the set easy to keep alongside other touring car service parts for rebuilds, tuning sessions, and routine drivetrain upkeep on compatible RC cars.

Other spare parts & accessories

TRF Universal Shaft BB Set, chassis accessory

€15.29

The TRF Universal Shaft BB Set brings the key running hardware for 2 universal shafts into one focused chassis accessory. With 4 ball bearings, 2 drive shafts and 10 E-rings in 1.2 mm size, it supports drivetrain service work on compatible TRF platforms and keeps the shaft assemblies equipped with the specified retaining parts. This set is intended for use with selected components in the TRF421 range, including item 51760 46 mm lightweight swing shafts, item 51761 46 mm drive shafts for double jointed shafts, item 51763 TRF421X front direct joints and item 51764 TRF421X differential joints. That makes it a targeted choice for builders working on the TRF421 chassis item 42384 and the TRF421X chassis item 42391, where the exact bearing and retention hardware matters. The included ball bearings are assigned specifically to the universal shaft setup rather than to general chassis use. On the bench, the combination of shafts, bearings and E-rings suits planned assembly work as well as replacement during maintenance. It fits naturally into a parts stock for race-oriented chassis service, where compatible driveline components are selected by reference to exact item numbers and shaft length.  Warning! Not suitable for children under 14 years.

Shock absorbers & springs

TRF VG O-Ring Damper Grease, model supply, 3 g

€16.191 kg = €5,396.67

TRF VG O-Ring Damper Grease is a dedicated model supply for damper maintenance, developed to support smooth sliding action and a cleaner seal at the O-rings. The blue grease comes in a 3 g case, making it easy to keep with regular bench supplies for suspension service. Its role is specific: the grease is intended for damper use rather than broad workshop application. When applied at the O-rings, it helps the damper move with less drag while also helping to prevent oil leaks. That combination matters during rebuilds and routine maintenance, where seal condition and controlled movement both affect how a shock unit works. The compact format also suits toolboxes, parts drawers and pit setups where small consumables need to stay easy to find. On a workbench, in a pit bag or beside a set of shock parts during servicing, this grease fits naturally into RC maintenance routines. It supports careful damper preparation for fresh builds, rebuilds and seal replacement, with a clearly defined use that keeps suspension work focused and tidy.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

TRF Wrench for Alu.Turnbuckles, RC tool

€14.79

The TRF Wrench for Alu.Turnbuckles is a dedicated RC tool for adjusting aluminum turnbuckle shafts with a compact format that fits naturally into detailed setup work. Its black-finished tip marks it out at a glance from item 42122, the wrench for blue titanium turnbuckle shafts with a silver tip, which helps keep the correct tool close at hand on a busy workbench. The anodized blue handle gives the wrench a clear TRF workshop identity, while ribbed grip sections support controlled finger placement during small steering or suspension link changes. A durable tip section is designed for repeated contact with aluminum turnbuckles, where clean engagement matters during routine maintenance. The tapered body keeps the tool easy to guide into tight spaces around assembled RC chassis and linkages. Printed TRF and TAMIYA RACING FACTORY markings on the handle add a technical finish that matches dedicated tuning equipment. On a setup bench, in a pit bag or beside a parts tray, this wrench supports quick adjustments before running and efficient checks after a session. It suits hobby maintenance where a single-purpose hand tool keeps turnbuckle work direct, organized and easy to identify among other RC tools.

Other spare parts & accessories

TRF417 V5 3.5mm Swing Shaft Cap, chassis part

€5.09

The TRF417 V5 3.5 mm Swing Shaft Cap is a dedicated chassis spare for compatible Tamiya racing platforms, supplied as 5 blades for half shafts in one set. The 3.5 mm size gives a concrete fit reference for maintenance work where matching the stated dimension matters to the driveline layout and the surrounding chassis parts. This spare part is listed for TB-Evo.7, TB-Evo.6 MS, TB-Evo.6, TRF419XR, TRF419X and TRF419 chassis. That model-specific compatibility helps narrow the choice when replacing worn half shaft hardware or preparing a pit box with the correct service parts for these platforms. The set format keeps multiple matching pieces together for routine upkeep, while the dedicated TRF417 V5 designation ties the part to a clearly identified component family rather than a generic hardware option. In workshop use, the blades can be kept on hand for scheduled maintenance or fitted when a compatible chassis needs fresh half shaft parts. The compact 5-piece contents also suit trackside servicing, where having the stated 3.5 mm version ready can simplify replacement work on supported chassis.  Warning! Not suitable for children under 14 years.

Gears & motor pinions

TRF420 Alu. F Direct Cups, spare parts, aluminum

€19.29

The TRF420 Alu. F Direct Cups set is a focused spare parts release for the front drivetrain of the TRF420 chassis. With 2 aluminum front direct cups and 1 swing shaft cap parts set in the pack, it provides the named replacement parts needed when wear begins to affect the front drive section and running efficiency starts to drop. The direct cups are made from lightweight aluminum and finished with a hard coating. That combination gives the parts a low-mass construction at a point in the drivetrain where repeated contact matters, while the coated surface is specified to support durability during regular use. The shape is designed for the TRF420 chassis, so the set suits planned maintenance as well as like-for-like replacement during a rebuild of the front end. Compatibility also extends to cars using the TRF420 Front Direct Pulley 37T, which broadens fitment within TRF420-based setups. On the bench, this set fits naturally into routine drivetrain servicing, especially when worn cups begin to influence how cleanly the front section transfers drive. It also makes sense as a workshop spare for race-day maintenance, where having the correct front-end hardware ready can shorten downtime between running sessions.

Axes & drive shafts

TRF420 C-Parts Front Uprights, chassis spare part

€6.39

TRF420 C Parts Front Uprights bring the specified spare steering components back to the front end of a compatible touring car chassis. The set is intended as a replacement for the TRF420 race car chassis and uses a 2-part upright layout that divides the arm and bearing housing into separate pieces, giving the assembly the structure required by this design. That 2-piece construction is the key technical detail here: the arm and bearing housing are molded as distinct components rather than a single combined part. This layout matches the newer TRF420 front upright design and can also be used on existing touring car racing platforms named in the compatibility data. The parts are molded in carbon fiber-reinforced material, a specification chosen here for higher rigidity in this steering area. The set contains 1 TRF420 C Parts pack. Compatibility covers TRF420, TRF419, TA07 and TB-05 PRO chassis cars, which makes this spare set useful both for direct replacement and for updating supported front-end configurations on other listed platforms. In a workshop setup, these uprights fit naturally into maintenance, rebuild or race-prep routines where worn steering hardware needs to be exchanged for the correct designated parts.

Axes & drive shafts

TRF420 E-Parts Rear Uprights, RC spare parts

€7.59

TRF420 E-Parts Rear Uprights are replacement suspension components for the TRF420 racing car chassis, made to return the rear end to its intended mounting layout. The carbon fiber-reinforced resin construction focuses on rigidity, so the upright keeps its shape where the shaft and bearing seats need stable support during running. Each set contains 1 TRF420 E Parts sprue, supplying the rear upright pieces shown for this chassis family. The bearing positions are precisely aligned, a detail that matters at the rear hub area where smooth rotation and efficient transfer depend on accurate seating. These parts are designed for use with 3 mm diameter shafts, and they work with cars using Item 51639 TRF420 D Parts suspension arms. That combination makes them a direct maintenance choice when worn or damaged rear suspension hardware needs to be replaced with the correct matching parts. On a workshop bench, these uprights fit into a focused chassis refresh where the rear suspension is being rebuilt around the original TRF420 geometry. They also suit race-day spares storage, where keeping the right molded parts on hand helps return the car to running condition with the intended component match.

Other spare parts & accessories

TRF420 F-Parts 4deg HC, RC spare parts

€7.99

TRF420 F-Parts 4deg HC are spare hub carrier parts made for the TRF420 racing car chassis. The set supplies the dedicated carrier shape used at this point in the suspension and steering assembly, with carbon fiber-reinforced resin construction that adds rigidity where bearings, shafts and linkages meet under load. This revised version was developed specifically for the TRF420 platform rather than carried over unchanged from the TRF417, TRF418 and TRF419 era. The updated design has greater resistance to shocks and crashes, which matters most at the hub carrier because this area takes repeated impact from track contact and wheel-side forces. The 4 degree specification defines the geometry of the part itself, while the mirrored pair format matches left and right installation. Upper and lower flanged tubes are identical, which keeps the hardware layout consistent when servicing the assembly. These parts are designed for use with 3 mm diameter shafts and work with cars using TRF420 D Parts suspension arms. On a race chassis, hub carriers are often replaced after heavy contact or updated during setup changes, so a dedicated spare set keeps maintenance focused and the car ready for the next rebuild. The precise molded openings and mounting points support clean installation alongside the matching suspension components.

Gears & motor pinions

TRF420/419 Gear Diff Bevel Set, model spare parts

€5.89

The TRF420/419 Gear Diff Bevel Set is a drivetrain spare-parts set for selected Tamiya chassis, built around redesigned bevel gears for the newer TRF419 gear differential unit. As replacement internal parts, these gears support accurate restoration of the differential mechanism when the original bevel gears show wear through repeated running and maintenance cycles. The set is described for the TRF419 gear differential unit and also appears in the designation for TRF421X, TRF420 and TA08, making it relevant for several closely related platforms. The redesigned gear shape is specified for the newer differential unit with large oil capacity, a detail that matters when matching internal parts to the correct generation of assembly. The pack contains 2 Gear Differential Unit Bevel Sets in the GV parts category, providing a clear service quantity for workshop stock or scheduled rebuilds. This kind of spare part fits naturally into bench maintenance between race meetings, setup revisions or routine transmission overhauls. Kept alongside other drivetrain consumables, the bevel sets help return a compatible gear differential to its intended internal configuration with the correct replacement parts on hand.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

TRF420/419/418 Cross Joint, spare parts set

€4.19

The TRF420/419/418 Cross Joint is a spare parts set for a broad range of Tamiya chassis platforms, bringing together the small connector hardware needed for targeted maintenance and replacement work. In the set are 6 pieces, shown as black cylindrical connector parts, silver metal pins and split rings, giving a clear mechanical match for compact linkage or joint assemblies within the stated fitment range. Compatibility extends across TD4 chassis, TD2 chassis, M-08 CONCEPT chassis, M-07 CONCEPT chassis, TA08 PRO chassis, TA07 MSX chassis, TA07 MS chassis, TA07 PRO chassis, TA06 PRO chassis, TB-Evo.7 chassis, TB-Evo.6 MS chassis, TB-Evo.6 chassis, TB-05 PRO chassis, TRF420X chassis, TRF420 chassis, TRF419XR chassis, TRF419X chassis, TRF419 chassis, XV-02PRO chassis and XV-01 PRO chassis. For TD4 chassis and TD2 chassis, the set is used with 22028. That specific pairing helps when checking fit before a rebuild or when keeping matching service parts ready for repeated chassis upkeep. The small-format parts suit bench work where worn connectors, pins or retaining pieces need a direct replacement instead of a full assembly change. Laid out as separate hardware components, the set supports precise servicing on compatible racing and off-road platforms where correct fit matters during ongoing maintenance.  Warning! Not suitable for children under 14 years.

Gears & motor pinions

TRF420/419/TA-07 Gasket (4), spare part set

€5.59

The TRF420/419/TA-07 Gasket set brings the shared gear differential seal used in the TRF420, TRF419 and TA07 into the Tamiya spare parts range as a dedicated 4-piece replacement pack. Each gasket is a flat ring with a profiled center cutout and 4 mounting holes, shaped to sit within the differential assembly where accurate positioning matters during service work. Replacing worn gaskets at the right time helps keep the differential unit properly sealed and ready for continued use. The 4 included pieces provide matching replacements for maintenance sessions, rebuilds or parts-box stock, especially on chassis that use the common gear differential design named in the compatibility list. The brown fibre-style gasket material shown in the set is suited to its role as a sealing layer between mechanical parts, while the identical cut pattern across all 4 pieces supports consistent fitment. In workshop use, these gaskets suit routine diff overhauls on compatible touring chassis, whether the goal is refreshing a frequently run car or preparing spare seals before the next rebuild. Kept alongside other service parts, the set gives TRF420, TRF419 and TA07 owners the exact gasket type specified for these gear differential units.

Axes & drive shafts

TRF420/TA-07 Direct Pulley (37T), RC spare part

€13.29

The TRF420/TA-07 Direct Pulley (37T) is a dedicated RC spare part for front drivetrain service on compatible chassis cars. Its integrated front direct pulley and holder form 1 molded assembly, trimming 2 g compared with the separate-part layout used on earlier TRF chassis and keeping the rotating section lighter. Included 0.2 mm and 0.3 mm shims allow pulley position and clearance adjustment during installation, which is especially useful when the part is fitted on chassis other than TRF420. The pulley flange pushes into the pulley with a snap-fit connection, creating a compact assembly around the central hub opening. Direct cups are mounted with screws rather than the 2 x 9.8 mm pins used on the previous chassis generation, so cup replacement can be handled separately from the pulley itself. The set contains 1 TRF420 front direct pulley and 4 shim washers, with 2 pieces in each shim thickness. In workshop use, this part suits routine drivetrain refreshes after wear or damage, and it also supports careful fitment tuning where clearance needs fine adjustment. Compatibility covers TRF420 and TA-07 chassis cars, while TRF419 fitment requires separately sold front direct cups.

Other spare parts & accessories

TRF420X Stiffener Nut, model accessory, blue

€13.79

The TRF420X Stiffener Nut set brings a clearly specified hardware option to model maintenance, replacement and setup work. With 5 blue nuts in the pack, the set gives a concrete match for builds or repairs where the TRF420X designation is the key reference and small fastening parts need to be identified quickly on the bench. The blue finish adds a visible sorting cue when hardware is laid out beside other screws, spacers and fittings, helping keep similar small parts easier to separate during assembly. The nut format points to a threaded fastening role rather than a decorative add-on, so the set suits practical workshop tasks built around securing or replacing existing hardware. The 5-piece count also supports repeated service work, whether one nut is needed for a direct replacement or several are prepared for ongoing maintenance across the same model platform. On a work surface, these nuts fit naturally into parts trays, setup stations and repair sessions where compact hardware is handled one piece at a time. For model builders keeping TRF420X-specific spares ready, the set provides a straightforward stock of matching fastening components in a distinct blue finish.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

TRF421 A Parts Upper Arms, model spare parts

€7.99

TRF421 A Parts Upper Arms are model spare parts made for the TRF421 platform, supplying the designated upper arm components for suspension maintenance and chassis rebuild work. The set focuses on one exact assembly group, which makes it easier to replace worn or damaged pieces while keeping the build aligned with the original parts layout. As A Parts, these components belong to a defined section of the TRF421 parts structure rather than a general hardware mix. That clear designation helps when sorting workshop stock, planning a rebuild, or selecting the correct replacement set after track use. Upper arms play a central role in the suspension layout by linking key mounting points and supporting the geometry that guides wheel movement through the chassis travel. Using the correct replacement group helps preserve the intended fit within that section of the model. This set suits bench maintenance, race preparation and post-run servicing when the chassis is stripped for inspection. It also fits well into a spares collection kept ready for fast turnaround between practice sessions, rebuilds and ongoing setup work on the TRF421.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

TRF421 Axle Shafts, RC spare part, double cardan

€15.79

These TRF421 axle shafts are a dedicated RC spare part for double cardan joint shafts and are supplied as a 2-piece set for the TRF421 chassis kit. The pair gives the drivetrain matching replacement components where a rebuild, maintenance cycle or worn shaft calls for the original fit. Each shaft combines a silver cylindrical section with black joint ends, and the visible cross-hole and threaded end show the mechanical connection points used in the assembly. The double cardan layout is designed for articulated drivetrain movement, so the shaft can work through the steering and suspension motion built into the chassis. As a chassis-specific spare part, the set is aimed at accurate fitment rather than universal use, which keeps parts selection clear during workshop preparation. On a bench setup, the 2 matching shafts suit routine service work on the TRF421 platform and help keep left and right replacement parts consistent within the same drivetrain area. For racers maintaining a competition chassis between runs, this set supports quick parts planning by focusing on one exact component group for the TRF421 kit.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

TRF421 C Parts Uprights, RC spare part

€6.49

TRF421 C Parts Uprights provide a direct replacement set for the TRF421 chassis, focusing on the suspension area where accurate part geometry matters during maintenance. The black moulded parts are shaped as dedicated uprights, with the mounting structure needed to restore the original layout when existing components are worn, damaged or missing. Their compact technical form suits bench work that calls for the correct chassis-specific fit rather than a universal workaround. The moulded construction supports clean alignment with the surrounding hardware, and the C parts designation helps identify the set quickly within a larger spares collection. For regular RC maintenance, keeping model-specific replacement parts on hand can shorten downtime after contact on track or wear from repeated running sessions. These uprights fit naturally into workshop routines such as scheduled servicing, partial rebuilds and pre-race checks on the TRF421 platform. They also make a practical addition to a pit box or home parts organiser, where clearly identified replacement sets help keep repairs focused on the exact section of the chassis that needs attention.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

TRF421 D Parts, suspension arms for RC models

€8.99

TRF421 D Parts suspension arms are replacement components for a compatible RC model chassis, supplying the left and right arm shapes needed where suspension geometry and mounting accuracy matter. The pair is shown in black molded material with a mirrored layout, so each side follows the intended orientation within the assembly. Each arm uses a lightweight truss pattern with large triangular openings, molded reinforcement ribs and smooth curved edges. That structure concentrates material around the load-bearing sections and the connection areas rather than filling the whole shape solid. Several circular mounting holes are formed directly into each piece, and the visible bushing-style inserts mark the points where compatible hardware is fitted. Hexagonal recess details and molded reference marks add further visual cues when sorting parts during maintenance. These components suit rebuilds, wear replacement or a fresh chassis assembly where the original arm set needs to be renewed. In a workshop setup, the mirrored pair can be matched side by side before installation, helping keep the suspension layout organized and the mounting sequence clear on a compatible TRF421 platform.  Warning! Not suitable for children under 14 years.

Shock absorbers & springs

TRF421 Damper Oil Seals, model spare parts

€4.39

The TRF421 Damper Oil Seals are spare parts made for the damper system on the TRF421. Supplied as a 4-piece set, they provide the key sealing parts needed when servicing compatible dampers and refreshing worn internal components. Inside a damper, the oil seal sits at a critical point where smooth shaft movement and oil retention need to work together. Replacing used seals can help restore the damper's intended function during maintenance, especially when rebuilding shocks after repeated running sessions. The 4 matching pieces make sense for work across a complete set of dampers, keeping the rebuild consistent from corner to corner. As compact workshop parts, they fit naturally into routine chassis care alongside cleaning, inspection and fresh damper oil. On the bench, these seals suit planned rebuilds as well as targeted repairs when a damper needs attention. For TRF421 owners who keep setup changes and servicing close under control, having the correct oil seals on hand supports a more orderly maintenance routine.  Warning! Not suitable for children under 14 years.

Shock absorbers & springs

TRF421 Damper Parts, RC spare parts set

€5.69

TRF421 Damper Parts are a dedicated RC spare parts set for the damper area of the TRF421 platform. The pack brings together black molded components such as eyelet-style connectors, ring-shaped mounts and slotted retaining pieces that support attachment, pivoting and secure placement within the suspension assembly. These parts are suited to maintenance work where small connection points have worn, gone missing or need replacement after heavy running. The eyelet forms are designed for linkage-style mounting, while the clip and ring elements handle locating and retaining tasks around the damper hardware. Using model-specific replacement parts helps preserve the intended fit of the assembly and keeps service work focused on the exact section that needs attention. On the workbench, the set supports routine rebuilds, race-day spares management and targeted repairs without replacing larger assemblies unnecessarily. It fits naturally into a parts box for ongoing chassis upkeep, especially when several small connectors are best renewed together to return the suspension area to proper working order.  Warning! Not suitable for children under 14 years.

Gears & motor pinions

TRF421 Drive Belt, replacement part, 116T

€10.19

The TRF421 Drive Belt 116T is a dedicated replacement part for the drivetrain of the matching TRF421 chassis. Its closed-loop form and evenly spaced inner teeth are made to run around the corresponding pulley path, creating the mechanical link that carries rotation through the transmission during RC use. The 116T specification identifies the belt size for the intended setup and helps maintain the original drive ratio and belt path of the chassis. The black belt material is flexible enough to route through the drivetrain layout while the toothed inner surface is shaped for positive engagement with matching gears or pulleys. This makes the part relevant during routine maintenance, a full rebuild, or the replacement of a worn belt after repeated running sessions. As a single drivetrain component, it is best chosen by the exact designation rather than by appearance alone. In workshop use, the belt fits naturally into service tasks where the transmission is being refreshed or restored to its stated specification. On a race chassis, a correctly matched drive belt helps keep the power system operating through the intended pulley sequence, so the rest of the drivetrain can work as designed.  Warning! Not suitable for children under 14 years.

Gears & motor pinions

TRF421 Fr. Direct Pulley 37T, RC spare part

€11.19

The TRF421 Fr. Direct Pulley 37T is a dedicated RC spare part for drivetrain service on compatible model setups. Its circular pulley form, central hub and evenly spaced outer teeth are built for direct engagement with a toothed belt, so rotational motion can be transferred through the front drive section with the specified 37T configuration. The black component uses a perforated inner disc with multiple round cutouts, a detail that removes material from the rotating section while keeping the outer toothed ring and hub structure intact. The raised hub section provides the mounting point, and the toothed circumference guides the belt along a defined path instead of relying on friction contact. This makes the part relevant wherever a worn pulley, damaged teeth or drivetrain refresh calls for a like-for-like replacement. The studio image also shows a ring-shaped companion part with an inner groove, indicating a matching hardware element within the spare-part set. In workshop use, the pulley suits routine maintenance, rebuilds and parts replacement after extended running sessions. It fits naturally into a spares box for racers and tuners who keep belt-drive assemblies working with the correct front transmission hardware.  Warning! Not suitable for children under 14 years.

Gears & motor pinions

TRF421 Gear Diff Set, RC differential parts set

€39.99

The TRF421 Gear Diff Set brings the core parts of a gear differential into one RC maintenance and assembly pack, with a 37T differential case, bevel gears, cross pieces and metal outdrive cups arranged for a focused driveline rebuild. The included oil, gasket plate and sealing parts support the internal mechanism where the gears rotate inside the closed housing. Inside the set are 2 black housing halves, 2 large silver bevel gears, 4 smaller bevel gears, 2 white cross-shaped internal parts, 2 metal shafts or pins, 2 small straight pins, 2 ring bearings, blue O-rings, washers, shims, spacer discs, clips and screws. These parts work together through a clear mechanical sequence: the bevel gears sit inside the case on the cross pieces, the outdrive cups connect at each side, and the housing closes around the assembly with the gasket and screws. The bearings support the rotating sections, while shims and spacers help position the moving parts within the differential body. This set suits workshop use, scheduled maintenance and replacement of worn differential internals on a TRF421 build. On the bench, the laid-out parts make it easy to sort the assembly stages, check each sealing and spacing component, and rebuild the differential with the required hardware close at hand.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

TRF421 Rear Body Posts, RC spare parts

€10.19

TRF421 Rear Body Posts are RC spare parts for the rear bodyshell mounting area, intended to restore the correct shell position on a compatible TRF421 setup. When the rear mount has worn, bent or been damaged in use, replacing these posts helps return the bodyshell to its proper height and alignment so the chassis can be prepared with the intended fit. As BB parts, they belong to a specific TRF421 parts grouping rather than a universal hardware assortment. That makes them a focused choice for maintenance, repair and setup work on the matching platform. Rear body posts handle a precise task at the back of the chassis: they support the shell where mounting position influences how the bodyshell sits over the rear section and how cleanly the mounting holes line up. In regular bench work, spare posts are practical to keep on hand for rebuilds after contact, routine wear replacement or setup refreshes before the next run. The compact format suits a pit box, workshop drawer or parts case, where dedicated replacement components help keep RC maintenance organised.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

TRF421 Wheel Axles, chassis accessory, 2 pcs

€13.79

The TRF421 Wheel Axles set supplies 2 matching axle parts for the TRF421 chassis kit, giving maintenance builds and replacement work the exact component type named for that platform. Each axle uses a grub screw attachment, a fastening method that fits the specified chassis layout and keeps the connection method consistent with the intended hardware. The parts shown here have a machined metal construction with a forked end, a smooth cylindrical shaft, a transverse hole and a threaded tip. That geometry matters during assembly because it defines how the axle seats, aligns and connects at its mounting point. As a 2-piece pack, the set covers a paired replacement rather than a mixed assortment of hardware. The note on fit is equally specific: these axles are not compatible with clip type shafts, so the connection standard is clearly separated before installation starts. This set suits workshop stock for the TRF421 chassis kit, whether the goal is a direct replacement, a rebuild after wear, or keeping matching spare drivetrain parts ready between running sessions. The focused pack format also makes it easy to keep the correct axle type on hand for planned service work on the same chassis.  Warning! Not suitable for children under 14 years.

Gears & motor pinions

TRF421/420/419 Spur Gear 116T M0.4, spare part

€4.49

The TRF421/420/419 Spur Gear 116T M0.4 is a dedicated spare part for compatible Tamiya racing chassis, built around a 116-tooth layout and module 0.4 specification. That combination makes it a direct drivetrain replacement when the original gear shows wear, helping restore the intended transmission setup for continued running and regular workshop service. Its role sits at the center of the drivetrain, where tooth count and module need to match the chassis design exactly. The pack contains 1 spur gear, so maintenance can stay focused on the specific part that needs replacement rather than a larger mixed set. The source data also names compatibility with the TRF418 chassis in the long text, while the short designation states TRF421/420/419; this copy therefore follows the current product designation without extending fitment beyond the provided naming. As a model accessory in the Models Supplies category, it suits bench stock for rebuilds, wear replacement and planned servicing. During routine maintenance, a fresh spur gear can be fitted when drivetrain wear becomes visible or when a rebuild calls for the stated 116T M0.4 specification. Kept in a parts case or workshop drawer, it gives compatible chassis a like-for-like replacement ready for the next service interval.  Warning! Not suitable for children under 14 years.

Screws & ball head screws

TRF421/X 3x2.6mm Hex Step Screw, model spare set

€9.79

The TRF421/X 3x2.6mm Hex Step Screw set is a dedicated spare set for model maintenance, built around an exact fastening format rather than a generic replacement. With 4 matching screws in 3x2.6 mm, it supports repair work where the specified size needs to be retained for the original assembly layout. The hex step screw form matters in use because it combines the fastening function with a defined shoulder profile, making it suitable for connection points that depend on this exact geometry. Keeping the stated 3x2.6 mm size avoids guesswork during servicing and helps maintain consistency across repeated repairs. The 4-piece count also makes the set practical for replacing worn or missing hardware while keeping identical spares on hand for later workshop jobs. On the bench, this set fits the kind of maintenance routine where small hardware needs to match the original specification closely. It suits model builders who sort parts by size and type, and it gives existing assemblies a straightforward way to be refitted with the correct screw format after disassembly or wear.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

TRF421/X 3x20mm Damper Shaft, model spare part

€6.19

The TRF421/X 3x20mm Damper Shaft set is a dedicated spare part for suspension servicing on compatible model setups. With a 3 mm diameter, 20 mm length and 2 shafts in the pack, it provides the core replacement component needed when a shock unit is being rebuilt or refreshed. Used inside the damper assembly, each shaft forms the moving element that guides the shock through its travel. Replacing a worn or marked shaft can help restore smooth damper action and keep the suspension working evenly across a matched pair. The compact 3 x 20 mm format also makes this set a practical choice for keeping key maintenance parts ready between rebuilds, whether the workbench is set up for routine servicing or for preparing a chassis after repeated running sessions. For hobby maintenance, a dedicated spare like this avoids replacing complete shock assemblies when only the shaft needs attention. The 2-piece pack fits naturally into parts storage for suspension rebuilds, setup checks and ongoing chassis care.  Warning! Not suitable for children under 14 years.

Screws & ball head screws

TRF421/x 5x6x4mm Hex Ball Nut, model spare part

€6.79

The TRF421/x 5x6x4mm Hex Ball Nut is a dedicated model spare part for maintenance, repair and parts replacement in compatible assemblies. Its specified 5 x 6 x 4 mm format gives builders a concrete reference when matching existing hardware, helping avoid guesswork during service work. This set contains 2 hex ball nuts, making it suitable for replacing a matched pair where even hardware matters across the same mechanism. The hex form supports tool engagement during installation, while the ball nut design suits applications that call for this exact component style rather than a general-purpose nut. Kept in a workshop drawer, spares case or rebuild tray, the set adds a clearly identified fastening part that can be selected by size and type. During routine upkeep, rebuilds or targeted repairs, a correctly specified spare like this helps restore a compatible model assembly with the same stated dimensions. The compact format also makes it practical to keep on hand alongside other service hardware for race-day checks, bench work or scheduled replacement of small mechanical parts.  Warning! Not suitable for children under 14 years.

Screws & ball head screws

TRF421/X 5x7x5mm Hex Ball Nut, model spare part

€6.49

The TRF421/X 5x7x5mm Hex Ball Nut set supplies 5 matching spare parts for detailed model maintenance where exact hardware size matters. Each nut measures 5 x 7 x 5 mm, giving a clear specification for replacing worn fastening points in compatible assemblies and keeping mechanical connections consistent during service work. The hex form allows tool-based fitting and removal, which is useful when access is tight and adjustments need to stay controlled around small moving parts. As a dedicated spare part set, these nuts suit routine workshop tasks such as replacing lost hardware, refreshing used link points, or keeping matching replacements on hand for future repairs. The pack count of 5 supports repeated maintenance without mixing unmatched pieces from different sources. On the bench, this set fits neatly into organised model servicing, whether a current build needs a direct replacement or an existing chassis is being checked over after running sessions. The compact dimensions make it easier to match the required hardware before installation and help keep compatible mechanisms assembled with the intended fit.  Warning! Not suitable for children under 14 years.

Gears & motor pinions

TRF421/X Diff. Case Parts Bag (37T), spare part

€7.79

TRF421/X Diff. Case Parts Bag (37T) is a model supplies spare part created for differential-related service work. The designation identifies the component group directly, making it easier to match a replacement to the correct area of a compatible build when worn or missing parts need to be exchanged. The 37T marking provides a concrete specification within the part name, which helps separate this bag from other drivetrain or case components in a workshop stock. As a dedicated replacement rather than a general accessory, it suits planned maintenance, rebuilds and the careful upkeep of running gear assemblies. The bag format also keeps the included parts grouped together instead of loose in a parts box, which supports clearer storage and faster identification during repair sessions. On the bench, this spare part fits naturally into routine model servicing, whether a differential is being refreshed after use or a stored chassis is being brought back into running condition. It also works as a practical reserve component for builders who keep key drivetrain spares ready between race-day checks and workshop maintenance.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

TRF421/X Shaft 1.6x9mm, model spare part

€6.19

The TRF421/X Shaft 1.6x9mm is a dedicated model spare part for double cardan assemblies, built around a clearly stated 1.6 x 9 mm shaft size and supplied in a pack of 5. That combination gives maintenance benches and race boxes a direct replacement option when a matching driveline pin is needed, without relying on broad, unspecific hardware choices. Its role is straightforward: this shaft belongs in a double cardan setup, where the correct diameter and length matter for fit within the joint assembly. The 5-piece pack supports repeated servicing across more than one maintenance session and helps keep identical replacements on hand for rebuilds. Because the data identifies this part specifically as a shaft rather than a general accessory, the search value sits in the exact designation and measurement, which makes it easier to match against an existing TRF421/X parts list or a worn component removed during service. On the workbench, this kind of spare suits routine drivetrain upkeep, parts-box organisation and targeted replacement before the next running session. In a workshop stock drawer or trackside tool case, the compact 5-pack keeps the required size ready when a double cardan assembly calls for the same 1.6 x 9 mm specification.  Warning! Not suitable for children under 14 years.

Gears & motor pinions

TRF421/X Spur Gear Nut Blue, model accessory

€7.29

The TRF421/X Spur Gear Nut Blue is a dedicated model accessory for the drivetrain area, supplying a specific replacement part for compatible RC builds and maintenance work. Its blue finish gives this small fastening component a clear visual identity on the bench, where quick part recognition matters during rebuilds and servicing. Used at the spur gear mounting point, the nut supports accurate replacement when an original part is worn, misplaced or being swapped during routine upkeep. The compact format makes it easy to sort into organiser trays, hardware boxes or spare-parts drawers alongside other workshop essentials. Because the data identifies this part by its exact TRF421/X designation, it also helps keep parts selection focused on the intended application instead of relying on generic hardware. On a home workbench, in a club pit area or during pre-run checks, a dedicated spare like this keeps drivetrain maintenance moving with less interruption. It fits naturally into regular service routines where small fastening parts are checked, replaced and kept ready for the next rebuild.  Warning! Not suitable for children under 14 years.

Screws & ball head screws

TRF421X 3x6mm Hex Flat Screw, model spare part

€11.89

The TRF421X 3x6mm Hex Flat Screw is a dedicated spare part for model maintenance, repair and exact replacement work. Its stated 3x6 mm specification gives a clear reference for matching an existing fastener in a compatible assembly, which helps keep servicing focused and avoids the guesswork of mixed hardware. The hex drive format is designed for use with a matching hex tool, allowing controlled tightening during bench work. A flat head profile sits flush at the intended fixing point, which supports a tidy fit where this screw type is required. The pack contains 5 screws, useful for replacing missing hardware, refreshing worn fixings or keeping a few matching parts ready in a workshop drawer. As a model accessory rather than a general household fastener, it belongs in planned upkeep of compatible hobby builds. This spare part fits naturally into regular maintenance sessions, whether a model is being checked after running, rebuilt section by section or restored with matching hardware kept close at hand. The compact pack size also works well for parts storage alongside other workshop essentials used for ongoing model care.

Other spare parts & accessories

TRF421X A Parts, suspension arm spare part

€8.79

TRF421X A Parts Upper Suspension Arm (2) is a dedicated spare part set for the TRF421X platform. The pack contains 2 upper suspension arms, giving a direct way to replace worn or damaged suspension pieces and return the chassis to its intended running condition. Within an RC chassis, the upper suspension arm is part of the linkage that guides wheel movement as the suspension works through bumps, load changes and cornering forces. Replacing this section can help bring back the original fit of the suspension area when a heavily used car starts to show play or after contact has stressed the arm. The A Parts designation also makes this set easier to identify when sorting workshop stock or matching replacement components to an existing build. This spare part suits routine maintenance, race-day repairs and keeping key chassis components ready between running sessions. For builders who maintain a TRF421X regularly, a matched 2-piece set supports quick parts changes and a more orderly spares setup at the bench or track.

Other spare parts & accessories

TRF421X Alum. Knuckle Arm, model accessory, blue

€52.49

The TRF421X Alum. Knuckle Arm set brings a clearly specified replacement part to model work, with 4 blue aluminium components supplied under the TRF421X designation. The defined pack count and named part type help keep maintenance, repair and parts selection accurate when a build calls for this exact component group. Aluminium gives the set a distinct material specification, while the blue finish makes the parts easy to identify alongside other chassis hardware during setup or rebuild work. Because the data names the knuckle arm directly, this set suits focused replacement planning rather than broad, undefined spares buying. The 4-piece format also supports work across multiple mounting points where matching parts are required in one purchase. On the bench, the set fits naturally into organised parts sorting, rebuild sessions and component-led tuning work. It also serves as a practical choice when an existing assembly needs the named TRF421X knuckle arm part in matching blue aluminium rather than a generic substitute.

Other spare parts & accessories

TRF421X Alum. Upper Arm Mount A Blue, model part

€22.89

The TRF421X Alum. Upper Arm Mount A Blue is a dedicated model part for chassis maintenance, replacement work and focused setup changes. Its blue aluminium construction gives the component a defined place within a tuned build, where accurate fit at the upper arm mounting area matters during servicing. As a TRF421X-specific part, this mount is suited to repairs that call for the correct designation rather than a generic substitute. The aluminium format makes it a practical choice for workshop use, where repeated assembly and disassembly demand a cleanly machined component. The Upper Arm Mount A position is central to suspension-related rebuild work, so using the matching part helps keep a project consistent with its intended layout. The blue finish also aligns visually with performance-oriented chassis hardware often used in competition-focused model platforms. Whether the task is replacing a worn mount, refreshing a race chassis or keeping spare hardware ready at the bench, this part fits naturally into a model maintenance routine. It works well for organised parts storage, planned rebuilds and trackside servicing where the exact TRF421X reference is the detail that keeps work moving.

Other spare parts & accessories

TRF421X Aluminium Chassis Plate, chassis part

€99.99

The TRF421X Aluminium Chassis Plate is a dedicated lower deck for the TRF421X platform, bringing a model-specific aluminium base into rebuilds, maintenance work and chassis updates. As a single replacement part, it addresses the central structure of the car where the main platform layout begins, making it relevant when a worn or damaged lower section needs to be exchanged. Compatibility is stated for both the TRF421 and TRF421X chassis, which keeps this part closely tied to those 2 racing platforms rather than a broad universal fit. The supplied quantity is 1 aluminium chassis plate, giving a clear match for targeted spare-part planning. The data also states an installation condition for TRF421 use: this aluminium sub-deck and the corresponding motor mount are used as a set when this deck is fitted to that chassis. That requirement matters for workshop preparation because it defines the matching hardware arrangement for the conversion. On the bench, this lower deck suits routine servicing, accident repair and planned chassis refresh work where the main plate is the part being replaced. It also fits organised spare-part storage for TRF421 and TRF421X running gear, where exact platform compatibility is more useful than a generic chassis component.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

TRF421X Aluminum Motor Mount, RC Spare Part

€69.99

The TRF421X aluminum motor mount is a dedicated RC spare part for the matching chassis platform, combining a blue anodized finish with the firm structure of machined aluminum. As the component that holds the motor in place within the drivetrain area, it supports accurate placement during rebuilds, maintenance work, or replacement of a worn original part. Its role sits at the center of the chassis layout, where motor position influences how adjoining drivetrain parts line up and operate together. The anodized blue surface gives the part a clear visual match for performance-focused workshop builds, while the aluminum base brings the crisp, technical look associated with competition-grade RC hardware. Because this is a model supply rather than a complete vehicle, the focus stays on exact replacement and platform-specific compatibility within the TRF421X setup. On the bench, this mount suits routine servicing, race-day spares planning, and selective chassis refresh work. It can be fitted when restoring a used assembly, replacing a damaged holder, or keeping a matching component ready in the pit box for the next maintenance session.

Other spare parts & accessories

TRF421X Aluminum Upper Arm Mount B Blue Part

€22.89

The TRF421X Alum. Upper Arm Mount B Blue is a model spare part shaped for suspension-related maintenance on the TRF421X platform. Its blue aluminum construction gives this mount a clear material identity and a direct role within the chassis, where an upper arm mounting point needs the correct designated version. As an Upper Arm Mount B component, it is suited to replacing a worn part during servicing or keeping a build supplied with the proper hardware for repair work. The aluminum format makes it a focused choice for model workshop use, especially when a chassis requires the exact mount position rather than a generic fitting. The blue finish also helps distinguish this version from other small chassis parts during setup, storage or rebuild tasks. For model maintenance, a clearly identified suspension part can save time when sorting components on the bench. This part fits naturally into rebuild sessions, race-day spares storage or routine chassis upkeep. It can be kept on hand for planned servicing, damage replacement or parts organisation within a TRF421X setup, where the correct mount designation matters as much as the material itself.

Shock absorbers & springs

TRF421X Carb. Bumper Holder 2mm, model part

€17.99

The TRF421X Carb. Bumper Holder 2mm is a dedicated model part for the front end of a compatible chassis build. Its carbon construction and 2 mm specification give builders a clearly defined replacement or upgrade component when the bumper mounting area needs a matching plate. As a bumper holder, this part is shaped for a specific mechanical role rather than general use. The flat carbon format suits setups where low weight and exact material choice matter, and the stated 2 mm thickness helps when comparing an installed part against a fresh replacement. In workshop use, that clear specification can save time during maintenance because the part can be matched directly to the required position. The TRF421X designation also keeps the component tied to its intended platform instead of a broad universal fit claim. This part fits naturally into repair sessions, race-day spares planning, or a careful chassis refresh between runs. On the bench, it supports a straightforward parts check for the front bumper mounting area and helps keep a competition-focused build consistent with its existing setup.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

TRF421X Carb. Rear Stiffener 2mm, model part

€11.99

The TRF421X Carb. Rear Stiffener 2mm is a dedicated model part for the TRF421X platform, built to add a 2 mm carbon brace at the rear of the chassis. Its focused role makes it useful for builders who tune a car through specific structural changes rather than broad part swaps, with the rear section addressed directly by a single component. Carbon gives this stiffener a rigid, lightweight construction suited to competition-oriented setup work. As a rear stiffener, it is intended for one defined mounting area, which helps keep tuning changes controlled and easier to track during rebuilds and test sessions. The 2 mm thickness is a concrete specification for matching the part to the required setup and compatible chassis layout. Used as a replacement or upgrade part, it supports maintenance as well as planned setup variation within the TRF421X range. On the bench, this kind of part fits naturally into detailed chassis preparation before practice or race use. It suits builders who compare setup changes step by step, whether refreshing a worn rear brace or preparing a car with a firmer rear chassis configuration for the next run.

Other spare parts & accessories

TRF421X Carbon Upper Deck Front, model spare part

€19.19

The TRF421X Carbon Upper Deck Front is a model spare part specified as a 2-piece front upper deck in 2 mm carbon. That combination gives the chassis a clearly defined replacement for the front upper deck area, with the material and thickness stated directly for accurate matching during maintenance. As a dedicated TRF421X part, it suits repairs where the front upper deck needs to be replaced with the same named configuration rather than substituted with a different layout. The carbon construction and 2 mm profile provide concrete reference points when checking compatibility within an existing build. The 2-piece format is also part of the stated specification, helping distinguish this front section from other deck parts in the chassis. For workshop organisation, the exact naming makes it easier to sort spares by position, material and thickness before assembly or rebuild work begins. On the bench, this part fits naturally into routine chassis servicing, rebuild preparation or race-day spares planning for the TRF421X. Keeping the front upper deck specification aligned with the rest of the car helps maintain a consistent setup when worn or damaged parts need replacement.

Other spare parts & accessories

TRF421X Carbon Upper Deck Rear 2-Piece 2 mm

€19.19

The TRF421X Carbon Upper Deck Rear 2-Piece 2 mm is a dedicated chassis supply for focused RC maintenance and rebuild work. Its carbon construction and 2 mm thickness define the part clearly, while the rear 2-piece format matches the specified layout for the TRF421X platform. Used in the upper section of the chassis, this component supports accurate replacement when an original deck is worn or damaged. The carbon material keeps the part aligned with competition-style RC setup needs, and the split rear design gives the assembly the exact form stated for this version rather than a one-piece alternative. As a model supply, it belongs in planned servicing, rebuild preparation and parts stocking for ongoing chassis care. Batteries are not included. On the workbench, this is the kind of part reached for during a measured refresh of a race chassis, when the goal is to restore the intended structure with the correct rear upper deck format. It also fits neatly into a spares case for track-day repairs, where having the specified 2 mm carbon component on hand can keep maintenance work focused and efficient.

Other spare parts & accessories

TRF421X Carbon Upper Deck, model chassis part

€42.49

The TRF421X Carbon Upper Deck is a dedicated chassis part for model building and maintenance, combining a 1-piece layout with 2 mm carbon construction. That format gives the upper section a clean, exact deck shape for rebuilds, replacement work and compatible tuning setups where the correct part geometry matters. As a model supplies component, this deck is defined by its material and structure rather than by decorative detail. The carbon plate construction keeps the part slim while the single-piece form avoids split sections across the upper span. The 2 mm specification provides a clear reference when matching the part to an existing build or preparing workshop stock for future service work. The designation TRF421X identifies the intended part family, which helps keep maintenance and replacement planning aligned with the correct chassis platform. On the bench, this kind of upper deck fits naturally into repair sessions, scheduled part changes and fresh chassis assemblies that call for the specified top plate format. It also suits hobby storage where clearly identified spare parts save time during rebuilds and setup checks.

Other spare parts & accessories

TRF421X Cooling Fan Post, model accessory, black

€29.49

The TRF421X Cooling Fan Post is a dedicated model accessory for RC setups that need a defined mounting point for a cooling fan. Its black finish gives the part a restrained technical look that sits neatly within detailed chassis layouts, while the stated weight of 20 g adds a concrete reference for parts selection and setup planning. This accessory is identified by the exact TRF421X Cooling Fan Post designation, which helps when matching replacement parts during maintenance or when refining an existing build with the correct hardware. The part belongs to the models and accessories range and is listed within model supplies, placing it clearly in the workshop side of the hobby rather than as a complete vehicle or kit. The black colour keeps the appearance consistent with many competition-focused assemblies where visible hardware is kept understated. On the bench, this component fits naturally into rebuilds, repairs and specification-led upgrades where the right mounting part matters as much as the fan itself. It also suits organised spares storage, where the exact name and 20 g reference make selection easier during ongoing chassis work.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

TRF421X D Parts, suspension arm set

€9.39

TRF421X D Parts Lower Suspension Arm 2 is a focused replacement set for the TRF421X platform, supplying 2 lower suspension arms for the D section of the chassis. The set supports precise maintenance work where suspension geometry depends on the correct arm shape and fit, making it a practical choice for rebuilds, repairs and regular workshop preparation. Within an RC chassis, the lower suspension arm forms a key link between the suspension mounting points and the wheel assembly, guiding movement as the suspension works over changing surfaces. Using the specified D Parts set helps keep the build aligned with the intended TRF421X layout instead of mixing unmatched components. The 2-piece format also suits common service needs, whether one arm is needed immediately and the second is kept in reserve, or both matching positions are refreshed together during a larger overhaul. On the bench, this set fits naturally into routine chassis care after contact damage, wear or a full strip-down. It also makes sense as a spare kept with race-day equipment, where having the correct TRF421X suspension parts close at hand can shorten interruptions between running sessions.

Shock absorbers & springs

TRF421X Damper Cylinder, model spare part

€38.99

The TRF421X Damper Cylinder set provides 2 replacement cylinders for damper service on compatible Tamiya model applications. As a dedicated suspension spare part, it supports precise maintenance work where the original cylinder bodies need to be renewed to keep a shock unit properly assembled. Each cylinder is intended for damper rebuild and repair tasks rather than general-purpose use. The 2-piece count suits paired shock work, so both sides of an axle setup can be refreshed in one service step when matching parts are required. In a tuning bench or repair area, a dedicated cylinder set also helps keep parts selection focused on the exact suspension section being rebuilt. Batteries are not included. This spare part fits naturally into routine workshop use, whether a chassis is being stripped for maintenance or a damper set is being rebuilt after repeated running sessions. It also works well as a shelf spare for model owners who keep key suspension components ready for future service intervals.  Warning! Not suitable for children under 14 years.

Shock absorbers & springs

TRF421X Front Damper Stay Mount, model spare part

€19.69

The TRF421X Front Damper Stay Mount is a blue model spare part made for front-end chassis service and replacement work. Its dedicated form focuses on the damper stay mounting area, making it a direct choice when that specific fixing point needs renewal during maintenance or a rebuild. Used as a separate replacement component rather than a full assembly, this mount helps keep repair work concentrated on the exact section that has worn, been damaged or is being updated. The blue colour also helps with quick visual identification among other workshop parts during sorting, fitting and inspection. The product data confirms that batteries are not included, which fits its role as a non-powered chassis component rather than an electronic unit. No operating voltage, runtime or speed figure applies here, because this part serves a structural mounting function within a model setup. On the workbench, the mount suits routine chassis upkeep, front-end refreshes and spare-parts storage between running sessions. It also fits planned rebuilds where a dedicated front damper stay mount is needed to restore the intended layout with a matching replacement part.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

TRF421X Front Direct Cup, RC spare part set

€20.29

The TRF421X Front Direct Cup set is a dedicated RC spare part pack for focused maintenance on the TRF421X platform. With 2 matching front direct cups in one set, it provides the exact replacement format for this specific drivetrain area when worn parts need to be exchanged. As a model supply rather than a full kit, this set is built around precise replacement work. The direct cup design serves the front section named in the part title, which helps keep servicing accurate and avoids replacing unrelated assemblies. The pack format of 2 matching pieces suits symmetrical front-end maintenance and gives a clear fit for rebuild planning, workshop stock or routine parts rotation. Where a drivetrain component has taken wear through repeated running, a dedicated replacement like this keeps the repair centered on the affected section. On the bench, the set fits naturally into regular RC maintenance schedules, from checking drivetrain wear during a rebuild to preparing spares before track use. It also suits hobby storage systems where model-specific replacement parts are kept ready for fast servicing between running sessions.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

TRF421X Front Stiffener Carbon, model part

€5.99

The TRF421X Front Stiffener Carbon is a dedicated model part for the TRF421X platform, built around a clearly defined front-end role and a carbon material specification. Its designation points directly to the intended chassis family, which helps keep replacement and setup work aligned with the correct model rather than relying on universal parts. As a front stiffener, this component belongs to the structural area at the front of the chassis and is intended for targeted maintenance, repair or parts planning within that exact platform. The carbon construction gives the part a distinct material profile that suits model builders who sort components by function and specification. Because the data identifies this as a single named part rather than a general accessory set, the focus stays on exact fit within the TRF421X designation and on clear workshop organisation. This kind of chassis part fits naturally into bench work where a build is being refreshed, maintained or prepared with the correct front-end components. It also suits spare-parts storage for model setups that are managed by platform name, making the TRF421X designation and the front stiffener function easy to recognise at a glance.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

TRF421X Gear Diff Set, model accessory set

€39.99

The TRF421X Gear Diff Set is a model accessory set centered on drivetrain service for compatible hobby builds. Its designation points directly to the differential area, making it a clear choice when a workshop setup calls for a dedicated gear diff replacement or a matching spare kept ready beside the chassis. Within the Models & Accessories range and listed under Models Supplies, this set belongs to the maintenance side of model building rather than the finished vehicle itself. That makes it useful for planned rebuilds, parts sorting, and repair work where the differential assembly needs the correct set under a single name. The wording Gear Diff Set also gives a concrete search anchor for hobbyists looking specifically for differential-related spares instead of general accessories. Batteries are not included. On the bench, the set fits naturally into routine drivetrain work such as refreshing a used build, preparing parts before a rebuild, or keeping a compatible spare ready between track sessions. For collectors and active builders alike, the clear TRF421X designation helps separate this set from broader workshop stock and keeps parts selection focused on the intended assembly area.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

TRF421X GearDiff Joints BB, model accessory

€17.29

TRF421X GearDiff Joints BB is a dedicated model accessory for drivetrain-related maintenance and replacement work. The exact designation points to a specific component set within the TRF421X parts range, making it a focused choice when a compatible build needs the matching GearDiff Joints BB part. This accessory is supplied as a separate component rather than a general-purpose workshop consumable, which matters when service work depends on the correct fit within an existing assembly. The naming indicates use around the gear differential area, so it belongs in repair planning, rebuild preparation, or routine parts replacement where drivetrain wear has to be addressed with the proper matching piece. Because the provided data identifies the part by its exact designation, the clearest buying cue is precise part matching rather than broad category claims. On the bench, this kind of replacement part supports scheduled maintenance, targeted repairs after wear, or preparation of spare components for future service intervals. The compact format also makes it practical to keep alongside other model spares, so a compatible drivetrain can be returned to running condition with the correct designated part when needed.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

TRF421X Piston 4 Holes 4x1,2 BLK, model part

€8.19

TRF421X Piston 4 Holes 4x1,2 BLK is a dedicated model spare part for suspension servicing and setup work. The pack contains 4 black pistons, giving a consistent set for replacing worn internals or preparing matching damper builds where equal specification across all corners matters. The 4-hole design in a 4x1,2 configuration defines how shock oil passes through the piston during compression and rebound. That makes this part relevant when damping response needs to be kept consistent after maintenance or changed with a specific piston layout already in mind. The exact TRF421X naming also helps separate this version from other piston types during parts storage and workshop preparation. As a compact tuning and replacement component, it fits naturally into routine rebuilds, damper refreshes and planned setup changes where the internal shock specification is chosen deliberately rather than left mixed. On the bench, the set suits organised rebuild sessions where all 4 dampers are being refreshed together. It also supports trackside maintenance when a matching piston set is needed to return a compatible chassis to an even suspension setup after wear or damage.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

TRF421X Rear Body Mount, RC spare part, carbon

€19.99

The TRF421X Rear Body Mount is an RC spare part made for the rear shell mounting position on the TRF421X. Its carbon construction gives this component a light, technical material profile while focusing on the exact task named in the data: supporting the rear body mounting point where the bodyshell is fixed in place. Used in the rear section of the chassis, this part addresses a specific mounting area rather than a general upgrade category. That clear assignment matters when a worn, damaged or missing rear mount needs to be replaced with the correct component type. The designation points directly to the TRF421X platform, so the part fits into a model setup built around that series rather than a broad universal application. Carbon is also a familiar material choice in competition-oriented RC components, where low mass and clean part definition are often central to the layout of mounting hardware. In workshop use, the part suits routine maintenance, rebuilds after running sessions, or preparation of a fresh chassis setup. It can also serve as a direct replacement to restore the rear shell mounting position before the bodyshell is refitted and the model returns to the track.

Shock absorbers & springs

TRF421X Rear Damper Stay Mount, model spare part

€19.69

The TRF421X Rear Damper Stay Mount is a blue spare part for model maintenance, rebuilds and targeted replacement work. Its role is specific and functional: it provides the mounting point for the rear damper stay area, so a compatible chassis can be restored with the intended component rather than a makeshift substitute. Used during servicing, the mount helps return the rear suspension section to its proper attachment layout. The blue finish gives the part quick visual recognition on the workbench and in storage trays, which is useful when sorting hardware for a rebuild or preparing replacement parts before installation. As a dedicated spare part rather than a universal fitting, it is best matched to the TRF421X designation named in the part title. This kind of component fits naturally into routine chassis upkeep, whether replacing a worn mount after running sessions or keeping a fresh part ready in the spares collection. In a workshop setting, it supports cleaner maintenance planning by keeping the rear damper mounting area equipped with the correct replacement piece.

Other spare parts & accessories

TRF421X Rear Stabilizer, model accessory, Soft

€8.39

The TRF421X Rear Stabilizer Soft BLK/YL ME26 is a dedicated model accessory for chassis setup work, centred on the rear stabilizer as a defined tuning component rather than a general spare. The soft specification and the black and yellow identification make this version easy to distinguish when several setup parts are kept together at the bench. Used on the rear section of the TRF421X, the stabilizer belongs to the suspension tuning area where small hardware changes can be made with clear intent. The product name identifies it as a rear stabilizer and ties it directly to the TRF421X designation, which helps keep parts selection precise during maintenance, rebuilds, and planned setup changes. The soft rating gives this version its own place within a broader tuning routine, especially when comparing component options for different track conditions or handling targets. As a single-purpose accessory, it suits organised workshop storage, repeatable setup notes, and quick identification between runs. At the workbench, this part fits naturally into regular chassis servicing, rebuild preparation, or controlled suspension experiments on a TRF421X platform. On track days, it supports structured tuning sessions where rear-end changes are made one component at a time and then checked in the next run.

Other spare parts & accessories

TRF421X Upper Arm Nut Set Blue RC Spare Part

€22.89

The TRF421X Upper Arm Nut set in blue is a focused RC spare part for suspension maintenance where the exact fastening point matters. With 4 matching nuts in one pack, it supports clean replacement work on the upper arm position named in the designation and keeps the hardware consistent across the assembly. The blue colour gives the set a clear visual distinction during bench work, making the nuts easier to separate from other small fasteners in a parts tray or toolbox. That matters most during rebuilds, routine servicing or when a missing fixing needs a like-for-like replacement instead of a generic alternative. Because the data identifies these specifically as TRF421X upper arm nuts, the set is suited to precise parts management within that model platform rather than general mixed hardware use. This kind of small component often becomes important during suspension work, where secure fastening and correct placement keep the assembly process moving without interruption. Kept as workshop stock or added to a race-day spares case, the 4-piece set covers the named nut type in a compact format that is easy to store and quick to reach when maintenance is underway.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

TRF421X/TA-08 Urethane Bumper RC Spare Part

€7.69

The TRF421X/TA-08 Urethane Bumper is a dedicated RC spare part for the front end of compatible chassis builds. Its wide curved form, shallow centre dip and 2 mounting holes match the shape needed for direct placement, giving the front section a defined cushioning element where contact is most likely to occur. Made from urethane with a foam-like structure, the bumper adds a light impact-absorbing layer without introducing unnecessary complexity to routine maintenance. The textured surface and tabbed mounting points show its purpose clearly: this is a shaped replacement part rather than a universal pad that needs trimming or adaptation. That makes it useful for rebuilds, worn-part replacement and keeping a chassis configuration consistent between running sessions. The compact format also stores easily in a pit box or parts case alongside other maintenance essentials. On a workbench, the bumper supports straightforward servicing when a front-end contact part needs to be swapped. In regular RC use, it helps keep the intended front bumper setup in place for continued running with the matching TRF421X or TA-08 layout.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

TT-01 A-Parts Steering Arm Upright Spare Set

€15.49

The TT-01 A-Parts Steering Arm Upright spare set is made for the TT-01 TYPE-E chassis and brings key front-end components together in one molded parts group. Steering arm and upright sections are central to wheel guidance and mounting geometry, so a matching replacement set helps keep a build aligned with the original chassis layout during repair or maintenance. The scope of delivery contains 1x A-Parts with 26 pieces. Keeping the components on a single runner supports clear identification before removal and helps separate mirrored left and right shapes during assembly. The black molded parts format suits workshop use where individual sections may need to be replaced after wear, damage or a rebuild. Because this set is tied specifically to the TT-01 TYPE-E platform, it serves as a direct chassis component group rather than a universal assortment for unrelated RC models. On the bench, the set fits naturally into maintenance sessions that focus on steering hardware, upright mounting points and surrounding front suspension connections. It also supports planned refresh work on an existing TT-01 TYPE-E build when original molded sections need to be exchanged with matching replacement parts.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

TT-01 Alum.Bumper Stopper, chassis accessory

€13.99

The TT-01 Alum.Bumper Stopper is a chassis accessory for TT-01 Type-E, TT-01 Type-ES and TT-01D Type-E platforms, built to reinforce the front bumper area with a 2 mm aluminium plate. Mounted at the bumper section, it helps the urethane bumper keep its form while the chassis is in use, giving the front end a more controlled structure. The shaped plate uses a dedicated mounting layout for the listed TT-01 variants instead of a generic fit. Its aluminium construction brings a rigid support part to a section that regularly absorbs contact, and the blue anodized finish adds a clear tuning detail to the front of the chassis. The part is supplied as a bumper stopper, not as a full bumper assembly, so it works as a focused replacement or upgrade within an existing TT-01 setup. On a bench build, the stopper suits refresh work on a worn front end or a more detailed custom chassis configuration. Once installed, it supports the bumper section during regular RC running while keeping the visual style of the car clean and technical.  Warning! Not suitable for children under 14 years.

Shock absorbers & springs

TT-01 Urethane Bumper M, chassis spare part

€6.29

The TT-01 Urethane Bumper M is a chassis spare part for selected Tamiya on-road platforms, built around a urethane foam body that sits as the specified impact element on compatible assemblies. Its M-size format and simple plate shape make it a focused replacement choice when an existing bumper insert has worn down, compressed or needs to be renewed during routine maintenance. The part is supplied as 1 urethane foam bumper and is intended for TT-02RR, TT-02D, TT-02 TYPE-SR, TT-02 TYPE-S, TT-02 and TT-01 TYPE-E chassis. The component uses an elongated form with rounded corners and 2 oval mounting holes, a layout that matches the mounting points shown for this spare part and supports straightforward positioning on the relevant chassis area. As a dedicated replacement rather than a universal pad, it helps keep a build aligned with the exact platform list given in the technical data. This kind of spare part fits naturally into rebuilds after track contact, scheduled servicing between runs, or a fresh chassis setup where worn foam has lost its original form. On a parts bench or in a pit box, the single-piece delivery keeps the replacement clear and specific for the supported TT series platforms.  Warning! Not suitable for children under 14 years.

Gears & motor pinions

TT-01/DF-02 Ball Differential Set, RC drivetrain part

€64.49

The TT-01/DF-02 Ball Differential Set is an RC drivetrain upgrade designed to add a limited slip differential effect to compatible chassis. When 1 driven wheel loses contact with the surface, the ball differential helps maintain drive instead of letting power fade away, which supports steadier acceleration on mixed grip sections and uneven ground. This is an assembly-type differential set, and the included gearbox joints form part of the build. The mechanism is adjusted by tightening the 2x10 mm cap screw until the ring gear does not slip, then backing off within an adjustment range of up to 1 turn from the fully tightened position. During adjustment, the 2x5 mm cap screw is removed and then tightened again to prevent loosening. The instruction material also identifies parts such as disk springs, a ball thrust bearing, an 850 metal bearing, a screw bushing and a pressure plate cap, showing the internal layout of the unit and how the rotating parts are aligned. Fitment covers TT-02, TT-02 Type-S, TT-02D, TT-01 Type-E, TT-01 Type-ES, TT-01D Type-E, DF-02 and TT-02B chassis. For TT-02 Type-S, use with Item 53806 TT-01 Ball Differential Cup Joint for Universal Shaft. For TT-02B, MB16 6 mm O-rings are used in different positions depending on front or rear installation.

Other spare parts & accessories

TT-01/E B-Parts, chassis spare parts set

€21.29

The TT-01/E B-Parts set is a dedicated spare parts pack for the TT-01 TYPE-E chassis, combining suspension arm and body mount components in one replacement set. With 42 pieces in the scope of delivery, it supports repair work that restores key chassis connection points and shell mounting positions with parts matched to this platform. The set is supplied as 1x B parts tree and is intended for chassis TT-01 TYPE-E as stated in the product data. Suspension arm sections handle the wheel-side linkage points that guide movement at the chassis, while the body mount parts provide the posts and holders used to position the bodyshell on the car. Keeping these parts grouped in one pack helps when wear, damage or a rebuild calls for the original component shapes rather than improvised substitutes. This spare parts set suits workshop stock for ongoing TT-01 TYPE-E maintenance, whether a chassis is being repaired after running sessions or rebuilt around fresh mounting points. It also fits planned restoration work where suspension connections and shell supports need to be replaced together to return the model to its intended layout.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

TT-01/E/R Drive Shaft Set, chassis spare parts

€13.49

The TT-01/E/R Drive Shaft Set brings the core running gear back into service with 2 wheel axles and drive shaft parts made for TT-01D TYPE-E and TT-01 TYPE-E chassis. Black moulded sections and metal shafts combine the shapes needed for axle mounting, driven connections and secure fastening points, so the compatible chassis can return to smooth mechanical operation. This spare-parts set is aimed at the drivetrain area where rotation, power transfer and wheel fit all depend on correctly matched components. The included parts are supplied as 2 wheel axles and are intended for replacement rather than visual customising, which makes them useful when existing axle parts show wear, damage or loss. Threaded shaft ends support wheel attachment, while the formed housings and square drive ends match the technical layout shown for this set. As a dedicated chassis component, the set fits into regular maintenance work, rebuilds and repair sessions on compatible TT-01 variants. On the bench, the parts suit planned servicing as well as targeted fixes after heavy running. In a workshop setup for RC maintenance, the set helps restore the mechanical link between drivetrain and wheel assembly on the specified chassis types.  Warning! Not suitable for children under 14 years.

Gears & motor pinions

TT-01/E/R G-Parts Gear Set, drivetrain spare parts

€10.29

The TT-01/E/R G-Parts Gear Set is a drivetrain spare-parts set for the TT-01D TYPE-E and TT-01 TYPE-E chassis. With 8 included E/R/G parts, it provides a direct replacement option for gearbox-related components when wear, damage or a rebuild calls for matching parts inside the transmission area. The set is shown with molded black drivetrain pieces such as gear elements, housing-style parts and a ring-shaped spacer component. Toothed gears transfer motion by meshing with one another, while the shaped case parts support correct placement of the internal mechanism during repair or reassembly. This makes the set useful when a compatible chassis needs specific transmission parts rather than a full overhaul with unrelated components. The 8-piece format also keeps the scope focused on the relevant section of the build. On the bench, the set supports planned maintenance as well as targeted replacement after heavy running sessions. It also fits neatly into a spare-parts collection for TT-01D TYPE-E and TT-01 TYPE-E chassis, where matching drivetrain components help keep future repair work straightforward.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

TT-01/E/R Servo Horn Saver Set, chassis parts

€6.79

The TT-01/E/R Servo Horn Saver Set supplies dedicated chassis parts for several Tamiya on-road and drift platforms, with compatibility listed for TT-02B, TT-02FT, TT-02RR, TT-02D, TT-02, TT-01D TYPE-E and TT-01 TYPE-E. As a focused replacement set for the steering connection area, it helps keep servicing work aligned with the original layout of the compatible chassis. The scope of delivery contains 1x P parts sprue with 10 pieces. The moulded components are supplied together on the sprue, which helps identify the matching parts before removal and installation. The set is intended for the servo horn and saver section, where the steering servo transfers movement into the chassis linkage through correctly shaped mounting parts. Using a dedicated set avoids mixing unrelated shapes when worn or missing pieces need to be replaced on supported platforms. This kind of parts set suits routine workshop use, planned chassis refreshes and targeted repairs after heavy running sessions. Kept alongside other maintenance spares, it gives compatible TT-01 TYPE-E and TT-02 based builds a direct source for steering hardware when the original servo saver assembly needs attention.  Warning! Not suitable for children under 14 years.

Shock absorbers & springs

TT-01/TGS Urethane Bumper, chassis spare part

€5.99

The TT-01/TGS Urethane Bumper is a dedicated chassis spare part for selected Tamiya platforms, using a die-cut urethane foam shape to match the front-end layout of compatible models. Its tapered form and 2 oval cut-outs point to a defined mounting position, which matters when a worn or compressed bumper needs to be replaced with the correct part rather than trimmed from generic foam. Compatibility is stated for TT-02RR, TT-02D, TT-02 TYPE-SR, TT-02 TYPE-S, TT-02 and TT-01 TYPE-E chassis. The scope of delivery contains 1 urethane bumper. The foam construction gives this part the compressible structure expected from a bumper insert, while the elongated profile and rounded ends align with the narrow front section commonly used on these chassis families. As a model accessory rather than a complete kit, it is intended for maintenance, repair, or parts replacement on an existing build. This spare fits naturally into workshop tasks such as replacing an older front foam piece during a chassis refresh or keeping a correct backup part ready between running sessions. For collectors and drivers maintaining a compatible platform, a chassis-specific bumper keeps the parts choice focused and avoids guesswork during servicing.  Warning! Not suitable for children under 14 years.

Gears & motor pinions

TT-01/TNS/M-05 Bevel Gear Set, RC spare part

€6.39

The TT-01/TNS/M-05 Bevel Gear Set is an RC spare part for differential maintenance on selected chassis from the Tamiya range. Metal bevel gears with conical, angled teeth are designed to mesh within the differential assembly, where they help keep drivetrain movement consistent as the transmission changes load through corners and acceleration. This set is specified for M-06, M-06 PRO, M-05 ver.II PRO, M-05, M-05 PRO, TT-01D TYPE-E and TT-01 TYPE-E chassis. The scope of delivery contains 1 bevel gear set diff., making it a focused replacement choice when the differential internals need renewal rather than a full gearbox rebuild. The visible parts layout includes larger gears with square centre openings, smaller matching gears with round centre holes and a 3-arm metal piece shaped for the assembly. That combination points to the internal differential gear train rather than external transmission parts. In workshop use, this kind of spare part suits planned servicing after extended running sessions or a targeted repair when a compatible chassis shows drivetrain wear. Kept alongside other maintenance parts, it also helps support faster rebuilds between track sessions and regular bench work on M-05, M-06 and TT-01 TYPE-E based models.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

TT-01D/R/E B-Parts, RC spare parts set, 42 pieces

€24.49

This B parts set is made for the TT-01D TYPE-E platform and brings 42 replacement pieces together in one pack for targeted chassis repairs. The sprues combine suspension arms and body mount sections, making it easier to restore key mounting points after wear, impact, or a stripped thread has taken a car out of use. The molded parts layout groups mirrored left and right components, along with smaller brackets, linkage-style pieces and structural sections that support accurate replacement work. Keeping these parts in the original molded form helps with identification before removal from the sprue and allows the needed section to be selected without sorting through mixed loose hardware. As a dedicated spare parts set rather than a general assortment, it matches the TT-01D/R/E family named in the data and focuses on the areas most often involved in chassis rebuilds. On a bench between running sessions, the set supports quick replacement of damaged arms or mounts so the model can return with its intended structure intact. It also fits neatly into a parts drawer for routine maintenance, where having the correct B tree ready can shorten downtime when a specific chassis section needs to be renewed.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

TT-01E Urethane Bumper, RC spare part

€5.99

The TT-01E Urethane Bumper is a model car spare part shaped for the front end of chassis 58407. Its molded urethane form follows the contour of the mounting area, creating a clean interface between the chassis nose and the surrounding front structure during repair or parts replacement. The gray bumper piece uses a dense foam-like urethane material with an irregular rectangular profile, rounded corners and 2 recessed openings. Those cut-ins align the part with the chassis mounting zone and help position the bumper evenly when an existing piece has worn down or gone missing. As a dedicated TT-01E replacement rather than a universal pad, it is intended to match the original layout of this chassis type. The compact form also makes it a practical workshop spare to keep on hand for routine maintenance of a running model. This component fits naturally into rebuild sessions, front-end refreshes and chassis servicing where the original bumper needs to be exchanged for a matching part. In a parts box for RC maintenance, it covers a specific wear area with the correct shape instead of relying on improvised foam inserts.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

TT-02 A Parts Upright, chassis spare parts

€8.59

TT-02 A Parts Upright brings a focused replacement set to workshop repairs on compatible Tamiya on-road chassis. The 1x A-Parts pack contains 30 pieces and is intended for restoring worn or damaged sections with matching molded components that fit the original platform layout. Compatibility covers the TT-02 chassis as well as TT-02FT, TT-02RR, TT-02 TYPE-S and TT-02 TYPE-SR variants, which makes this set useful when several related builds share service parts on the bench. The black molded parts are suited to repair tasks around upright and chassis assemblies where exact platform matching matters during maintenance. As a dedicated spare-parts pack, the set supports targeted replacement instead of buying a full kit again. The grouped format also helps keep rebuild work organized when a damaged section needs to be exchanged during routine servicing. On a hobby bench, the pack can be kept alongside frequently used service parts for quick access during teardown and reassembly. It also fits planned maintenance on running chassis that need fresh molded components after wear, impact damage or repeated rebuild cycles.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

TT-02 Adjustable Upper Arm Set, RC chassis parts

€26.29

The TT-02 Adjustable Upper Arm Set adds a tunable suspension link setup to TT-02 based chassis, using turnbuckle shafts to adjust camber from 0° to 2°. That range gives model builders a clear way to alter wheel angle for track setup, cornering balance and alignment work while keeping the mechanism mechanical and direct. The set is compatible with TT-02, TT-02RR and TT-02D chassis and replaces the kit upper arm parts B13 and B17. Front arm assembly uses 3x18 mm turnbuckle shafts and a target overall length of about 49.5 mm, while the rear arms use the same shaft size with a target length of about 44.5 mm. The instructions also note left and right orientation on the front arms, suspension ball insertion, grease application at the mounting points and a 3x5 mm screw for camber adjustment examples. Use with assembly universal shafts rather than standard resin drive shafts. Item 42236 is used when adjusting. This set suits rebuilds, suspension maintenance and chassis tuning sessions where repeatable measurements matter. On a bench setup, the stated arm lengths and the 0° to 2° camber range give a concrete starting point before final checks with a camber gauge and further trackside refinement.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

TT-02 B Parts Suspension Arm for TT-02 Chassis

€14.29

The TT-02 B Parts Suspension Arm set supplies a focused replacement pack for the suspension section of compatible TT-02 chassis variants. With 48 pieces in the set, it supports repair and maintenance work where worn, damaged or missing parts need to be exchanged so the chassis can be rebuilt with matching components and a consistent fit. Compatibility covers TT-02FT, TT-02RR, TT-02D, TT-02 TYPE-SR, TT-02 TYPE-S and TT-02 chassis. That range makes the set useful for keeping several related platforms in service with one dedicated parts group rather than mixing unmatched components. The B parts designation also helps identify the correct section during workshop organisation, rebuild planning and parts replacement. The set is intended for model and RC use, where suspension geometry and secure mounting points matter during assembly and ongoing upkeep. On the bench, this parts pack suits routine servicing after repeated running sessions, accident damage or a chassis refresh during a larger rebuild. It also works as a practical spare set for hobby storage, so a compatible TT-02 platform can return to assembly or repair work with the correct replacement group already at hand.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

TT-02 Ball Bearing Set, RC accessory, 16 pieces

€35.49

The TT-02 Ball Bearing Set brings a direct mechanical upgrade to supported TT-02 chassis builds by replacing friction-heavy rotating points with 16 metal ball bearings. That change reduces drive losses in the transmission, so more of the drive system's output reaches the wheels with less drag during running sessions. This set is supplied as a 16-piece bearing pack and is intended for the TT-02RR chassis and the TT-02FT chassis. Ball bearings are a common first tuning step because they support smoother rotation than standard bushings and reduce resistance across the drivetrain. The lower friction can also help extend running time, while the bearing construction is stated to increase bearing life. As an RC accessory rather than a complete vehicle, the set focuses on one specific upgrade area and keeps the installation scope clear. On a fresh build or an already running chassis, the bearings suit workshop tuning aimed at cleaner transmission movement and more efficient power delivery. The compact metal components fit naturally into maintenance, rebuild, or upgrade sessions where the goal is a more refined TT-02 drivetrain rather than a visual change.

Axes & drive shafts

TT-02 C Parts Cup Joint, chassis spare parts

€9.99

The TT-02 C Parts Cup Joint set is a chassis spare parts pack for TT-02 platform maintenance, with 9 included pieces supplied as 1x C parts set. It supports direct replacement work on compatible TT-02, TT-02D and TT-02FT chassis, where matching joint and coupling sections are needed to keep the original mechanical layout in service. The set is intended for model workshop tasks such as replacing worn connection parts, refreshing a used drivetrain area or preparing a rebuild with the correct C section components. The included parts are shown as black moulded components with metal shafts, a combination suited to connection points that need accurate fit between linked assemblies. Because this pack is a dedicated spare parts set rather than a universal assortment, the chassis designation matters: TT-02RR is excluded and should not be paired with these parts. For rear axle work, the fit note is equally specific, as 2 sets are required to manufacture the long rear wheel axle. On the bench, this set suits planned servicing, fault tracing and parts replacement on compatible TT-02 family builds. It also works as a practical stock spare for ongoing upkeep, where having the correct C parts ready can shorten downtime between runs and rebuild sessions.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

TT-02 Cup Joint for Universal Shaft, RC part

€12.79

The TT-02 Cup Joint for Universal Shaft is a dedicated RC drivetrain part for TT-02 chassis builds using the 53792 RC Universal Shaft Assembly. This set contains 2 steel gearbox joint shafts that replace the standard molded drivetrain parts at the gearbox connection points, bringing a more precise mechanical link into the transmission layout. The steel construction gives these cup joints a clear material change at a high-load area of the drivetrain, where rotating parts meet and transfer drive through the universal shaft system. Each joint uses a stepped shaft section with a flange and a forked end profile shaped for its gearbox role, so the parts are built around the actual connection geometry rather than acting as a generic insert. The set is intended as a compatibility-specific upgrade, not a universal spare, and it must be paired with the 53792 RC Universal Shaft Assembly for use. In workshop use, these 2 joints suit maintenance, drivetrain refreshes and planned tuning on a TT-02 chassis already set up for universal shafts. They fit naturally into rebuilds where the gearbox end of the driveline is being updated with matching metal connection parts for consistent running.

Other spare parts & accessories

TT-02 D Parts Motor Mount, chassis spare parts

€6.49

The TT-02 D Parts Motor Mount is a chassis spare-parts set for the TT-02 platform, supplied as 1x D parts with 13 pieces. It is intended for the motor mount area and matches a wide group of compatible chassis versions, making it a practical choice when a build needs the correct replacement section rather than a universal workaround. Compatibility covers TT-02, TT-02B, TT-02D, TT-02FT, TT-02RR, TT-02 TYPE-S and TT-02 TYPE-SR chassis. The molded parts are presented as a dedicated D-parts tree, which helps keep part selection clear during maintenance and rebuild work. For RC model owners who keep several TT-02 variants in service, that shared fit can simplify spares storage and reduce guesswork at the bench. The 13-piece count also points to a defined component group for this area of the chassis rather than a mixed assortment of unrelated hardware. This set fits naturally into repair, restoration and routine upkeep of compatible TT-02 vehicles. It can be used when refreshing a worn motor mount section, replacing damaged original parts, or preparing a chassis for its next running session with the correct matching components from the TT-02 family.  Warning! Not suitable for children under 14 years.

Gears & motor pinions

TT-02 G Parts Gear Set, RC drivetrain spare parts

€7.19

TT-02 G Parts (Gear) brings the core internal pieces of a differential and gearbox service set into one focused spare-parts pack for compatible RC chassis. The layout shown includes differential housing cups, cross-shaped spider gear shafts, multiple bevel gears, a large spur gear and a small bushing or sleeve, giving a clear base for drivetrain maintenance where worn transmission parts need replacement. Inside the differential, the bevel gears and cross shafts form the mechanism that lets drive pass through the axle while allowing the left and right sides to rotate at different speeds in a turn. The housing cups hold these internal gears in position, while the larger toothed gears connect the differential assembly to the rest of the transmission. This makes the set useful for restoring gear mesh, replacing damaged internal parts or rebuilding a gearbox after heavy running. The black molded finish also makes the individual shapes easy to identify on the bench during sorting and fitting. In workshop use, the set suits routine servicing, targeted repairs and full differential rebuilds on a compatible TT-02 platform. It also works as a practical stock spare for RC owners who keep drivetrain wear parts ready between maintenance sessions.

Other spare parts & accessories

TT-02 Lower Deck, chassis frame for TT-02 models

€8.29

The TT-02 Lower Deck is the main tub frame chassis for a wide range of TT-02 platforms and provides the molded base that carries the running gear layout of the car. As the central lower structure, it supports the installation of drivetrain parts, suspension assemblies and electronics in the intended chassis arrangement, making it a practical replacement part for repair work or a new build based on an existing TT-02 setup. This lower deck is specified for TT-02, TT-02B, TT-02D, TT-02FT, TT-02RR, TT-02 TYPE-S and TT-02 TYPE-SR chassis. The scope of delivery contains 1 tub frame chassis. The molded construction uses a deep central tray, raised side walls, reinforcing ribs and multiple screw posts to create the structural base for the vehicle layout. Mounting areas at the front and rear connect with the surrounding mechanical assemblies, while the central section leaves room for the internal chassis components used in the compatible platforms. In the workshop, this part suits rebuilds after wear, damage or heavy use, and it also supports parts-based TT-02 projects that need a fresh lower frame. For maintenance benches, spare-parts storage or a full chassis refresh, the lower deck restores the correct foundation for the compatible TT-02 family.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

TT-02 Lower Deck, chassis part, hard black

€11.79

The TT-02 Lower Deck in hard black gives TT-02 platform builds a rigid main chassis base with a clean, neutral finish. Made from glass fiber-reinforced material, this lower deck is shaped for use as the central tub section in compatible chassis cars, where stiffness and accurate fit matter during assembly and setup. This version adds a black colour variation to the hard lower deck previously offered in white and blue. The hard specification is intended to increase rigidity in the chassis structure, which can help a model make fuller use of its suspension and drivetrain settings once the running gear is installed. As the main lower section of the chassis, the deck forms the mounting foundation for the surrounding mechanical parts and keeps the layout consistent across maintenance, rebuilds and tuning changes. The single lower deck is supplied as 1 piece. Compatibility covers TT-02, TT-02B, TT-02D, TT-02RR, TT-02 Type-S and TT-02T chassis cars. In workshop use, it suits a worn original part, a fresh rebuild or a colour-coordinated update where the black base is intended to sit neatly with the chosen bodyshell and livery.  Warning! Not suitable for children under 14 years.

Shock absorbers & springs

TT-02 Oil Gear Diff Unit, RC drivetrain upgrade

€37.99

The TT-02 Oil Gear Diff Unit brings an oil-filled differential setup to the TT-02 series, replacing the standard differential gear with a drivetrain assembly that supports smooth, efficient power transfer. Inside the unit, die-cast bevel gears work within a glass fiber-reinforced nylon gear case, while the gasket helps seal the housing for oil-filled operation. Setup changes can be made by selecting different oil grades or gear diff putty, which alters how the differential reacts as the chassis loads and unloads through turns. The assembly uses a ring gear, bevel pinion gear, O-rings, shafts and ball bearings to route drive through the gearbox joints with controlled internal movement. The instruction data specifies that oil should be filled only to the level of the differential axle, and the housing screws are tightened little by little in sequence to help prevent leaks. The included bevel pinion gear is used for the conversion, and the unit is not compatible with standard plastic drive shafts. Assembly universal shafts are used instead. This Hop-Up Option suits maintenance, rebuild and tuning work on TT-02 based RC cars where drivetrain response is part of the setup process. Compatible TT-02 series chassis can be equipped with the unit using the required matching parts for TT-02, TT-02D or TT02B applications.  Warning! Not suitable for children under 14 years.

Screws & ball head screws

TT-02/B 3x18mm Step Screw Set, chassis hardware

€6.29

The TT-02/B 3x18mm Low Fric. Step Screw set is a focused chassis upgrade for the steering arm area on the TT-02 and TT-02B platform. Each 3x18mm screw uses a low-friction finish that helps the steering linkage move with less drag at the pivot, supporting a cleaner and more exact response when the front end changes direction. The set contains 2 step screws and an included hex wrench for installation. These screws replace the standard parts used in TT-02 chassis steering arms, while the hex heads match the format used on other option parts in the range. The stepped construction combines a smooth shaft section with a threaded end, so the screw can locate the moving joint correctly while still fastening securely in place. For TT-02 owners, 2 screws are enough to complete a single chassis in this position. TT-02B owners should note that 4 screws are required for the corresponding setup. On a bench build, maintenance session or steering refresh, small hardware changes like this can make the front assembly feel more exact at the point where the linkage pivots. Compatible with TT-02 and TT-02B chassis, this set suits targeted replacement work as well as option-part tuning.

Axes & drive shafts

TT-02/D A-Parts Front Uprights RC Spare Parts

€16.79

The TT-02/D A-Parts Front Uprights set is a focused spare-parts pack for maintenance on compatible TT-02/D chassis builds. Supplied as 2 front uprights, it addresses a specific front-end component group and helps restore the intended mounting position in the suspension assembly. The parts are moulded pieces designed for direct use as A-Parts within the TT-02/D layout. That makes this set useful when wear, impact damage or repeated running has affected the original uprights and a full chassis parts replacement is unnecessary. Replacing only the front uprights keeps repair work concentrated on the affected area and supports a more efficient rebuild process. The pack format also provides a matched pair, which is practical when both sides of the front suspension need attention at the same time. In workshop use, this kind of spare set fits routine servicing, damage repair and planned refresh work between running sessions. The clearly defined component scope also makes it easier to keep a compatible chassis in running condition with the exact parts group needed for the front end.  Warning! Not suitable for children under 14 years.

Shock absorbers & springs

TT-02B Damper Stay, RC spare parts, front rear

€11.79

This TT-02B A-Parts set provides front and rear damper stays as replacement components for the TT-02B platform. The black molded parts arrive on a single sprue, making the individual sections easy to identify before removal and helping keep workshop handling orderly during repair or rebuild work. The damper stay is a key suspension mounting section, as it carries the attachment points for the dampers and helps position them correctly on the chassis. Replacing a worn or damaged stay can restore the intended mounting layout and bring the front and rear suspension back into proper alignment with the rest of the build. The connected runner format also helps keep smaller sections together until the moment they are needed. This is especially useful when several maintenance steps happen at once and parts need to stay sorted. On a bench setup, these replacement pieces suit routine servicing after heavy running, collision damage, or a full chassis refresh. They also fit neatly into a spares box for ongoing TT-02B upkeep, where having the correct front and rear damper stays ready can shorten downtime between rebuild sessions.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

TT01,TGS Toe-in Rear Upright, chassis part

€19.99

The TT01,TGS Toe-in Rear Upright is a chassis spare and tuning part for selected TT-01 platforms, adding 2 degrees of rear toe-in through the shape of the molded uprights themselves. Fitted to the rear assembly, the pair changes wheel alignment at the hub carrier position and gives the chassis a clearly defined geometry update. Compatibility is stated for TT-01 Type-E, TT-01 Type-ES and TT-01D Type-E. The scope of delivery contains 2 parts, covering the rear left and rear right positions as a matched set. Each piece has a molded body with a central cylindrical opening, side mounting arms and visible reinforcing ribs, all shaped for installation at the corresponding mounting points in the chassis. This makes the set suitable for replacing used uprights during maintenance or for introducing a specific rear setup on a rebuild. On a workshop bench, during a refresh of a running chassis or while preparing a second configuration, the pair gives model builders a straightforward way to change rear alignment with a dedicated component rather than improvised modification. The compact format also makes the set practical to keep with spares for TT-01 servicing and parts sorting.  Warning! Not suitable for children under 14 years.

Shock absorbers & springs

TT01D/R/E Urethane Bumper, chassis spare part

€4.79

The TT01D/R/E Urethane Bumper is a grey chassis spare part made for front-end replacement on compatible Tamiya on-road platforms. Its urethane foam construction sits at the nose section of the chassis, where this component forms part of the front bumper area and restores the intended layout during repair or routine maintenance. This spare part is listed for the TT-01 Series and also fits TT-02RR, TT-02D, TT-02 TYPE-SR, TT-02 TYPE-S, TT-02, TT-01D TYPE-E and TT-01 TYPE-E chassis. The set contains 1 urethane foam bumper, making it a focused replacement for a worn, compressed or missing original part rather than a mixed hardware pack. The grey finish matches the stated version, and the single-part format keeps parts selection clear when servicing several compatible chassis types. It suits rebuilds after repeated running sessions, front-end refresh work, or keeping a bench stock of key wear parts for supported platforms. In a workshop setup with multiple TT-01 and TT-02 variants, the shared fitment helps streamline maintenance planning across the compatible chassis range.  Warning! Not suitable for children under 14 years.

Shock absorbers & springs

TT01E/R/D A-Parts, RC spare parts set, 13 pieces

€7.19

This A-Parts set is made for TT-01D TYPE-E and TT-01 TYPE-E chassis and groups damper stay and gearbox frame components into one defined replacement pack. With 13 pieces in the set, it gives a direct way to service specific structural areas of a compatible RC model rather than searching across mixed hardware. The parts group suits maintenance work where the original mounting sections need renewal after wear, damage or a rebuild. Because the set is assigned to named TYPE-E variants, compatibility stays tied to the chassis family stated in the data. The scope of delivery contains 1x A-Parts set, which keeps the contents focused on this single component group. As a spare parts accessory in the Models & Accessories range, it fits naturally into bench stock for regular upkeep of an existing TT-01 platform. In workshop use, the set can be kept on hand for planned servicing or used when a damaged frame section interrupts running time. It also supports tidy restoration work on a compatible chassis where the goal is to return the original layout with the correct A-Parts group.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

TT01E/R/D D-Parts, battery holder motor mount

€13.49

The TT01E/R/D D-Parts set is a dedicated replacement pack for TT-01D TYPE-E and TT-01 TYPE-E chassis builds, centered on the battery holder and motor mount area. With 16 molded components in black, it provides the specific parts needed when these sections show wear, damage or loss during maintenance. The set is supplied as 1x D parts group and is intended for exact compatibility within the listed TT-01 variants rather than as a universal RC fitting. That makes it useful for restoring original mounting geometry in the chassis, especially where the battery holder, motor mount and related structural pieces need to be brought back into service. The molded format also keeps the individual shapes consistent across the full set, which matters when replacing interrelated chassis sections. On the bench, this spare pack fits naturally into routine RC upkeep, whether a drivetrain area is being refreshed, a damaged mount is being replaced or a stored chassis is being returned to running condition. It also serves as a practical stock part for TT-01 owners who maintain compatible platforms and want the correct D section ready for future repairs.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

TT02B C Parts, RC spare parts, suspension set

€15.29

TT02B C Parts provide a focused spare parts set for RC model servicing, centered on suspension arms and body mount components for the TT02B platform. The molded pieces arrive attached to sprues, which keeps the shapes together for identification before trimming and fitting at the workbench. The set is built around replacement and maintenance use rather than a complete vehicle build. In addition to the suspension arms and body mount elements named in the designation, the visible molded frame also carries related structural pieces that support chassis repair tasks and parts matching during upkeep. The black finish makes the contours, mounting holes and connection points easy to read while comparing old and new pieces side by side. This helps when checking orientation before installation and when separating the required parts for a specific repair. TT02B C Parts suit routine workshop jobs such as replacing worn running gear pieces, refreshing damaged mounting sections after use, or keeping spare components ready between driving sessions. On a hobby bench, the grouped sprues support a tidy workflow while the dedicated fit for the TT02B keeps the repair process focused on the correct chassis family.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

TT02B N Parts, drive shaft and wheel axle set

€10.49

TT02B N Parts provide a focused replacement set for compatible model vehicle maintenance, combining drive shaft pieces and wheel axle components in one pack. The black moulded parts are supplied on sprues, with metal pins and threaded posts already integrated into selected pieces, giving each assembly point a clear mechanical role during fitting. The set is suited to repair work where worn, damaged or missing drivetrain and axle parts need to be brought back into service with matching components. The drive shaft pieces handle rotational transfer within the running gear, while the wheel axle parts form the connection point for the wheel assembly. Slotted cylindrical sections and shaped mounting points help distinguish the individual parts before removal from the frame. This makes the set useful not only for direct replacement, but also for keeping spare components ready for workshop storage alongside an existing TT02B build. On the bench, the sprue format helps organise the parts before cutting and installation. During servicing, the grouped layout supports a more orderly check of axle hardware and drivetrain pieces, whether the task is a single-part swap or a broader chassis refresh for continued running use.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

Universal Toolkit, model tool set for 1:10 kits

€4.49

This universal tool set brings together the core hand tools and small hardware often needed around 1:10 model kits. The set contains 2 Allen keys, 4 grub screws and 1 cruciform wrench, creating a practical bench companion for assembly, adjustment and routine maintenance work. The cross-shaped wrench is suited to repeated fastening tasks where a firm hand position and quick tool changes matter. Its 4 socket ends place several sizes in one tool, so common nuts and fittings can be reached without switching between separate drivers. The 2 L-shaped Allen keys are useful for hex socket screws set deeper into components, where the short and long arms help with leverage and access. The 4 grub screws add spare fastening hardware for small locking points that need replacement or readjustment. Used beside a fresh kit build or during later servicing, the set supports the small, precise jobs that keep a model running cleanly. It fits naturally into a workbench routine for chassis tuning, hardware checks and part changes on 1:10 models, and the included mix of tools keeps the most-used essentials together in one place.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

Upright Lunch Box Spare Part Set for 58063

€11.29

This spare part set supplies 2 upright assemblies for the Lunch Box model 58063 and gives repair or rebuild work the matching components for a clean replacement. Each assembly pairs a molded white arm with a polished metal shaft, creating a compact mechanical unit that fits the role shown in the original layout. The arm on each piece has a round pivot opening at one end and 2 smaller linkage holes near the curved tip. That hole pattern supports different linkage mounting positions within the compatible control setup, while the threaded shaft end provides a clear fixing point during installation. The paired format matters here, because both matching pieces are supplied together rather than as a single side only. For maintenance work on a used chassis, that makes it easier to replace worn or damaged parts as a balanced set. The set suits workshop use when a Lunch Box 58063 needs fresh running gear hardware in the upright area or when an older build is being returned to working order. It also fits parts storage for ongoing RC maintenance, where model-specific replacements help keep a compatible vehicle ready for the next rebuild or repair session.  Warning! Not suitable for children under 14 years.

Shock absorbers & springs

Urethane Bumper M Blue, chassis bumper, 15 mm

€7.19

The Urethane Bumper M Blue is a chassis bumper for selected Tamiya touring car platforms, combining 15 mm urethane thickness with a light blue finish that stands out from the standard grey version. Mounted at the front of the chassis, the bumper forms a compressible contact zone that helps manage knocks during RC driving while giving the build a more individual appearance. Compatible chassis listed in the data are TT-02RR, TT-02D, TT-02 TYPE-SR, TT-02 TYPE-S, TT-02 and TT-01 TYPE-E. The urethane material keeps the part lightweight, which suits tuning setups where unnecessary front-end mass is best avoided. The blue colour also pairs visually with the OP682 aluminum bumper when that part is used, creating a coordinated custom look across the front section. The scope of delivery contains 1 bumper. This part suits rebuilds, replacement work and visual updates on existing chassis. It can be fitted when refreshing a used front end, when matching blue option parts across a build, or when preparing a chassis for regular circuit sessions where a foam bumper remains a core contact component.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

Urethane Bushing, model accessory, 10-piece set

€4.19

This set of 10 urethane bushings is made for model maintenance where small replacement parts need to match in shape and material across the whole pack. The compact cylindrical pieces are supplied as loose components, making them straightforward to keep with workshop spares or to allocate to a specific repair job. The product data identifies the set as MB23 / TB-02, which helps place it within an existing parts list or compatible model setup without relying on guesswork. The image shows 10 white porous cylinders arranged as individual inserts, highlighting their uniform size and consistent cut. That even format matters when several matching bushings are needed for the same mechanism or when older parts are being replaced together rather than one by one. Urethane construction also gives this pack a clearly defined material specification instead of a generic mixed-parts description. In practical use, the set suits routine servicing, parts replacement and keeping spare inserts on hand for later workshop tasks. The 10-piece quantity also supports repeated maintenance cycles, whether the aim is to refresh a current build or keep matching bushings available for future model work.

Shock absorbers & springs

V-Parts V1-11, RC spare parts set, C.V.A-Mini II

€7.69

V-Parts V1-11 C.V.A-Mini II is a chassis-specific spare parts set for selected Tamiya model vehicle platforms. The set contains 2 sprues with molded components arranged for replacement work, helping restore the intended fit of assemblies that use this parts group in compatible builds. The fitment list is the key detail here. The set can be used with TT-02, TT-02D, TT-02RR and TT-02FT chassis, and also with vehicles equipped with 50746. It also fits TT-01 TYPE-E vehicles equipped with 53619. Further compatibility covers DT-03 and DT-03T vehicles equipped with 54567, plus the DN-01 chassis. DT-02 XB cannot be used, and on DN-01 the set cannot be combined with 54028. That makes this set useful for planned maintenance, replacing damaged molded parts, or keeping an existing chassis configuration consistent with the required option setup. On the bench, the 2-sprue format makes it easier to identify the molded parts group before installation and compare the frames with the existing assembly. For workshop stock, rebuilds or chassis servicing, this set supports direct parts replacement within the stated compatibility range.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

Wheel Spacer/Blue (8), RC accessory set

€12.99

This wheel spacer set adds a precise tuning option to compatible RC chassis by shifting wheel position with small, measurable changes. The set contains 8 blue spacers and supports tread adjustment through 2 thicknesses, with 4 pieces at 0.5 mm and 4 pieces at 1 mm, so setup changes can be made in fine increments instead of one large step. The ring-shaped parts are suited to maintenance, replacement and chassis tuning where wheel fitment needs a controlled offset. Their compact washer-style form keeps the function straightforward: each spacer sits in the wheel mounting setup to alter position by the stated thickness. On DT-02 chassis, DT-03 chassis and DT-03T chassis, these spacers can only be used for the rear wheels. Scope of delivery: 8 spacers. The set works well as a small workshop supply for routine servicing, for rebuilding a used chassis, or for testing different rear wheel positions during setup changes. The blue finish also makes the individual spacers easy to identify when sorting tuning parts with other RC hardware and replacement components.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

WT-01 A-Parts Gearbox for RC Model Chassis

€13.99

The WT-01 A-Parts Gearbox supplies the main housing pieces for compatible RC model chassis builds, with 2 mirrored components arranged on a single sprue for clean identification before removal and assembly. The molded form shows the structural shell that surrounds the transmission area, with circular openings, recessed sections and shaped outer contours that match the mechanical layout these parts are made to serve. Each piece is injection-molded as a dedicated left or right half, allowing the gearbox area to be rebuilt with matching geometry rather than improvised substitutes. The visible posts and screw locations support accurate positioning during installation, while the enclosed housing format helps organize the internal drivetrain section within the chassis structure. This set is listed for 58231, 57825 and 58514, making it a focused replacement choice when one of those specified models needs original A-parts again. On a repair bench, the 2-part layout keeps the job straightforward: remove the sprue parts, prepare the mounting points and return the transmission case to its intended form. For restoration work, maintenance or keeping spare chassis components ready, this gearbox set covers the essential shell pieces without adding unrelated hardware.  Warning! Not suitable for children under 14 years.

Shock absorbers & springs

WT-01/TL-01B C-Parts, suspension parts set

€14.49

This C-Parts suspension set is made for WT-01 and TL-01B chassis and provides a focused spare-parts solution for repairs, rebuilds and routine workshop maintenance. The black injection-molded sprue holds the components in their original runner layout, making it easier to match each shape to the required position before cutting and fitting the parts into the chassis. The set centers on suspension-related pieces rather than general hardware, with multiple arm forms, mounting elements, ring-style pieces and a larger curved section visible on the frame. Molded part markings such as 12, 13, 15 and 20 support identification during the build or repair process, while smaller numbered and lettered references on the runner help distinguish neighboring pieces. This kind of layout is especially useful when replacing damaged components after running sessions or when restoring an older chassis to working order. On the bench, the sprue format keeps the parts together until they are needed, which helps maintain order during staged repairs. For hobby storage, it also makes this set practical as a model-specific replacement kept alongside compatible WT-01 or TL-01B chassis parts for future servicing.

Shock absorbers & springs

XL Urethane Bumper, RC chassis part for TT-02

€4.39

This XL urethane bumper adds a larger front impact buffer to TT-02 and TT-01 Type-E chassis cars while staying easy to adapt to different bodyshell shapes. The black urethane construction differs from the grey bumpers found on many on-road RC kits, giving this part a distinct look and a generous block of material for custom trimming. The bumper is supplied as 1 black urethane piece and is intended to be cut down to the size needed for the chassis and body combination in use. That cut-to-fit format helps align the foam more closely with the nose section of a touring car bodyshell, where contact in close running can mark or crack the shell. Instead of a fixed outline, the extra-large shape leaves room to remove only the material required for clearance around posts, mounts or body contours. As a chassis part, it focuses on front-end protection rather than styling changes. It suits workshop use when replacing a worn bumper, preparing a fresh bodyshell or setting up a different shell on an existing TT-02 or TT-01 Type-E platform. On indoor tracks, car parks or other smooth on-road running areas, the added urethane buffer helps take the edge off light contact before it reaches the bodyshell.

Other spare parts & accessories

XM-01 B Parts Body Mounts, spare parts set

€8.79

The XM-01 B Parts Body Mounts set provides the shaped structural pieces used to position and support the bodyshell on an XM-01 chassis. Moulded in black and laid out as a dedicated spare parts group, the set focuses on the mounting area where shell height, placement and attachment points need to line up cleanly with the rest of the build. Two main mounting plates form the core of the set, each with multiple screw holes and reinforcing ribs that guide stable installation. Long L-shaped support arms add a row of adjustment holes, allowing the mounting position to be changed in measured steps rather than by guesswork. A cross brace links the assembly with an additional connection point, adding another structural element to this replacement group. These are workshop spares intended for repair, maintenance or a fresh rebuild when original parts are worn, damaged or missing. Used during chassis servicing or parts replacement, this set helps return the shell mounting area to its intended layout so the bodyshell can sit in the correct position. It suits bench work focused on restoring fit and attachment rather than cosmetic changes, and it keeps an XM-01 build supplied with the specific parts needed for this section.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

XM-01 C Parts Uprights, chassis spare parts

€7.99

XM-01 C Parts Uprights provide a dedicated replacement set for the TAMIYA XM-01 chassis, centered on the wheel-mounting and suspension connection area where precise fit matters most. The black molded parts shown here include paired structural pieces for left and right installation, along with small matching rings and caps that complete the set for chassis service work. The main components feature circular seats for bearings or bushings, plus clearly formed pivot and mounting points that tie into the surrounding running gear. Reinforced ribs in the molding add shape to the upright structure, while the mirrored layout reflects the left and right geometry needed at each side of the chassis. This makes the set useful when an existing build needs damaged parts replaced, when a stored chassis is being brought back into running condition, or when spare hardware is kept on hand for routine workshop maintenance. On the bench, these chassis parts support a tidy repair process by replacing like-for-like XM-01 components instead of adapting universal pieces. During running sessions, correctly fitted uprights help the wheel assemblies sit as intended within the chassis layout, which is especially relevant after knocks, wear or repeated disassembly during tuning and upkeep.  Warning! Not suitable for children under 14 years.

Shock absorbers & springs

XM-01 Carbon Damper Stays, RC chassis upgrade

€36.99

The XM-01 Carbon Damper Stays FR set adds front and rear carbon damper stays to XM-01 PRO chassis cars, bringing a rigid mounting base to a suspension area that directly affects damper angle and response. The carbon plates use a multi-hole layout, so damper attachment points can be moved with purpose instead of staying fixed in one position. The set contains 1 front carbon damper stay, 1 rear carbon damper stay, 8 blue 5x6.55 mm ball connector nuts and 8 round head 3x10 mm socket screws. That hardware matches the stays for a clean installation and keeps the upgrade focused on the suspension mounting area rather than requiring separate fastener sourcing. The front and rear pair gives the same material specification at both ends of the chassis, which helps keep setup changes consistent when adjusting the car. Short size dampers are compatible as well and can be attached separately. The data notes this setup mainly for paved roads, where a lower, road-focused damper arrangement may suit the surface. On a tuned XM-01 PRO build, these stays support careful suspension changes for asphalt running, test sessions and setup refinement between runs. They also suit rebuilds where the goal is to update the front and rear damper mounting points with carbon parts and matching installation hardware.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

XM-01 D Parts, chassis spare parts, suspension arms

€7.99

XM-01 D Parts bring the correct suspension arm set back to the TAMIYA XM-01 chassis, whether the goal is replacing worn components or completing a chassis build with matching parts. The black molded pieces show the dedicated shape of this set clearly, with mirrored forms arranged for left and right installation points. The arm design uses reinforced triangular ribbing across each piece, adding structure to the molded form while keeping the mounting layout precise for the XM-01 platform. Cylindrical connection points at the ends define where the arms seat into the chassis assembly, and the molded geometry follows the specific layout required by this spare part group. The set is suited to workshop maintenance where damaged arms need to be exchanged for matching replacements, and it also supports rebuilds that call for the original D Parts designation. The compact component group focuses on a single chassis area, making it a direct choice when suspension hardware needs to be restored with the correct part family. On the bench, these parts fit naturally into repair sessions, rebuild work and planned spare stock for the XM-01 chassis. For model keepers who maintain running cars over time, a dedicated arm set like this helps return the suspension area to its intended configuration with parts made for that exact platform.  Warning! Not suitable for children under 14 years.

Gears & motor pinions

XV-01 G Parts Gears, spare part set for chassis

€4.79

XV-01 G Parts Gears is a spare part set for the gearbox section of selected RC chassis and supplies 4 dedicated components for transmission maintenance. The set is suited to builders who need the named G Parts area rather than a full rebuild pack, making it easier to replace the exact pieces used inside the drivetrain. Compatibility is stated for XV-01, XV-01 PRO, XV-01T, TD4, TD2 and FF-04 EVO chassis. That cross-platform fit makes the set useful for keeping several running models in service with one reference pack. The included parts are shown as dark mechanical components with toothed gear forms and mounting points, indicating their role in transferring drive through the gearbox assembly. As a chassis-specific spare set, it supports repair work after wear, damage or routine inspection of internal transmission parts. On the workbench, the set fits naturally into a maintenance routine built around checking drivetrain function, replacing worn gears and restoring smooth mechanical engagement in compatible chassis. It also works well as a backup spare kept with an RC parts collection for faster turnaround when a gearbox service is due.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

XV-01 K Parts Steering Arm Chassis Spare Set

€11.39

The XV-01 K Parts Steering Arm set supplies 9 molded components for chassis service work on selected Tamiya platforms. Designed for the steering arm area, the set supports accurate replacement when original parts are worn, damaged or missing, helping bring back the intended mounting layout and mechanical function. Compatibility is stated for the FF-04 EVO chassis, XV-01 chassis, XV-01 PRO chassis and XV-01T chassis, which makes this pack a practical match for several related RC builds. The black molded parts are suited to repair benches, rebuild projects and routine maintenance where the correct shape and fit are essential. The supplied pack contains 1x K-Parts set with 9 parts, giving a defined contents list for planning a chassis refresh or targeted replacement task. The data also notes that only KK parts can be used where specified. On the workbench, this set fits the kind of maintenance session where a steering assembly needs fresh hardware after wear or impact. It also suits keeping a compatible chassis in running condition between driving sessions, with the replacement parts ready to install into the matching platform.  Warning! Not suitable for children under 14 years.

Gears & motor pinions

XV-02 06 Module Spur Gear 70T, RC spare part

€3.69

The XV-02 06 Module Spur Gear 70T is a drivetrain spare part for XV-02 chassis cars, built around a 70-tooth gear profile in 0.6 module sizing. As a direct replacement component, it supports maintenance work when a worn transmission gear needs to be exchanged or when the drivetrain specification is being restored to the stated setup. The set contains 1 spur gear and 2 matching ring parts. The gear face shows a molded 70 marking for clear identification, along with a large central hole, smaller circular openings and recessed cutouts across the wheel. These visible details help distinguish the part during bench work and parts sorting, especially when several drivetrain components are stored together. The toothed outer edge is shaped for meshing within the transmission system used on the compatible chassis. In workshop use, this spare part suits routine servicing, repair after wear, or keeping a correct replacement ready in the pit box. Compatibility is stated for XV-02 chassis cars, so the part can be selected specifically for that platform instead of as a generic gear. The compact format also makes it practical as backup stock for regular running sessions and scheduled drivetrain upkeep.

Other spare parts & accessories

XV-02 B Parts Bumper Set for XV-02 Chassis Cars

€11.29

XV-02 B Parts Bumper is a dedicated replacement set for XV-02 chassis cars, bringing the specified front and rear bumper hardware together in one pack for maintenance, rebuilds and chassis refresh work. The set focuses on the bumper and body-mount area, where repeated running, body changes and routine workshop handling can call for exact matching parts. The contents are clearly defined: 1 front bumper, 2 front body mounts, 1 front stiffener, 1 rear bumper, 2 rear body mounts, 1 rear stiffener and 1 transponder stay. That 9-piece layout covers both ends of the XV-02 platform and keeps the front and rear mounting points aligned with the listed chassis fitment. The body mounts and stiffeners sit alongside the bumpers rather than as unrelated extras, so the set supports coordinated replacement across the same structural area. The transponder stay adds the specified mounting part for race or timing setups where that fixture is needed. Used during repair, scheduled maintenance or a fresh chassis build, this parts pack helps restore the intended XV-02 configuration with components named for the exact platform. It also suits keeping workshop spares on hand for track days, club running sessions or rebuilds after contact, where matching bumper and mount parts save time compared with piecing together separate replacements.

Other spare parts & accessories

XV-02 D Parts CasterBlock 6deg Spare Parts

€7.29

The XV-02 D Parts CasterBlock 6deg set adds a chassis-specific replacement pair to the Tamiya spare parts range, with 2 black moulded caster blocks supplied for steering and suspension service. The 6° specification and embossed 6 marking help identify the correct version at the bench when a rebuild calls for the matching geometry on both sides. These D parts are intended for XV-02 chassis use and are also compatible with XV-01, DB and TD chassis cars, which gives the set value across more than one platform in a parts box. The shape shown by each piece combines a central circular opening, a side mounting eyelet and a lower cylindrical connector section, indicating the attachment points needed for front-end assembly work. As a dedicated spare rather than a general hardware piece, this pair supports accurate replacement of the original specified component. In workshop use, the set suits routine maintenance after wear, damage or a strip-down for inspection. Keeping the correct 6° caster blocks on hand helps speed up repairs on compatible rally and buggy-based chassis, while the 2-piece pack provides the left and right parts needed for a matched front-end rebuild.

Axes & drive shafts

XV-02 E Parts, rear uprights spare set

€7.29

XV-02 E Parts brings the rear upright section for compatible XV-02 chassis cars back into the spare parts range, with 2 replacement pieces supplied for the rear suspension area. The set is intended for maintenance work where the original uprights need to be replaced after wear or damage. As E parts for the XV-02 platform, these components are made to match the rear upright position used on that chassis layout. That makes the set useful for planned servicing, repair work after hard running, or keeping matching replacements ready in a workshop parts box. The pack focuses on one specific component group rather than a mixed hardware assortment, which helps keep repairs targeted and straightforward when the rear end needs attention. In regular RC maintenance, rear uprights are one of the chassis-specific parts that need the correct match to restore the intended suspension arrangement. This set supports that job on compatible XV-02 cars with 2 identical replacement parts for the rear position. It fits naturally into rebuild sessions, trackside repairs, or routine upkeep between runs when worn suspension parts need to be exchanged.

Other spare parts & accessories

Molybdenum Grease 10g, model lubricant tube

€6.991 kg = €699.00

Molybdenum Grease 10g is a model lubricant designed for moving assemblies where precise application and controlled coverage matter. The paste-like grey-black grease comes in a tube with a pointed nozzle, making it easier to place a small amount directly onto contact areas while working on model vehicles at the bench. The formulation is identified for use as a lubricant for model vehicles, giving maintenance work a clear technical focus rather than a general household use. Its density is listed as 0.96 ±0.03 g/ml at 15 °C, and the kinematic viscosity is specified as above 20.5 mm2/s at 40 °C. The grease is insoluble in water and has a slight inherent odour. A drop point above 200 °C and a flash point above 200 °C add further material data for hobbyists who maintain drivetrains, rotating shafts and other loaded contact points. In practical use, the narrow nozzle supports careful servicing on compact mechanisms where grease needs to reach a specific spot instead of the surrounding structure. It suits routine workshop tasks such as refreshing lubrication on gears, bearings, joints and shafts in model vehicles, helping keep maintenance neat and targeted.  Warning! Not suitable for children under 14 years.

Shock absorbers & springs

Top-Force 2017 Hi-Cap Dampers, model upgrade set

€66.99

Top-Force 2017 Hi-Cap Dampers bring a focused suspension upgrade to the Top-Force 2017 with 4 aluminum damper cylinders, 4 coil springs and #400 damper oil in a 20 ml bottle. The high-capacity oil damper design gives the chassis a more substantial damper setup than the standard specification, with the visual appeal of aluminum cylinders at each corner. Alongside the main damper parts, the set also contains resin and small metal components needed for the conversion. The package is built around a full 4-damper layout, so the Top-Force 2017 can be equipped across the whole vehicle rather than with a partial change. #400 damper oil is supplied in the set, which keeps the fluid specification aligned with the included hardware. Compatibility is stated for Item 47350 Top Force 2017, making this a model-specific option rather than a generic suspension assortment. On the bench, the set suits builders refining an existing buggy with a dedicated damper package matched to the named chassis. Once fitted, the 4 matching dampers and springs give the model a uniform suspension look and a clear mechanical upgrade centered on the oil damper system.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

1150 Ball Bearing Set, RC bearing pack, sealed

soon available again

The 1150 Ball Bearing set brings a direct drivetrain upgrade to compatible RC chassis by replacing plain rotating points with sealed ball bearings. Each bearing uses rubber-covered sides and an 11 mm outer diameter, 5 mm inner diameter and 4 mm width, creating a compact format for hubs, axles and other moving assemblies where clean rotation matters. Installing ball bearings is a common first step when tuning running performance because they reduce drive loss and support smoother movement through the transmission. The sealed construction adds high dust resistance, which helps the bearings keep turning freely in regular road, buggy and track use. The pack includes 4 bearings for targeted replacement or routine maintenance on frequently used assemblies. Compatibility covers a broad list of chassis, including TD4, TD2, DF-02, DF-03, DT-02, DT-03, DT-03T, TT-02, TT-02B, TT-02D, TT-02RR, TT-02 TYPE-S, TT-02 TYPE-SR, TT-02FT, TT-01D TYPE-E, TT-01 TYPE-E, M-05, M-05 PRO, M-06, M-06 PRO, M-07 CONCEPT, M-08 CONCEPT, MF-01X, RM-01, TB-04, TB-04 PRO, TRF101, TRF102, TRF103, F103GT and F104 Ver.II PRO. On a workshop bench, the 4-piece set suits regular servicing before the next run or a focused upgrade on a fresh chassis build. Once fitted, the bearings support freer rotation in the moving parts that shape how efficiently the model puts power down.  Warning! Not suitable for children under 14 years.

Screws & ball head screws

2x8mm Hex C-sunk Head Tapping Screw, model screws

soon available again

This pack contains 10 hex C-sunk head tapping screws in a 2x8 mm size for model building, maintenance and parts replacement. The countersunk head sits into a matching recess so the fastening point stays level with the surrounding surface, which is useful where body panels, brackets or other fitted parts need a neat finish. The tapping design forms its thread directly in the receiving material during installation, making these screws suitable for compatible model assemblies that use self-tapping hardware. The 2 mm diameter and 8 mm length place them in the small-format hardware range used for detailed fastening jobs, and the hex head gives a defined drive point for controlled fitting. As workshop stock, a 10-piece pack helps keep replacement fasteners on hand when a build is interrupted by missing or worn screws. These screws fit naturally into bench tasks such as replacing lost hardware, refreshing older assemblies or securing parts during a rebuild. In regular model maintenance, having the same head style and size ready can keep repairs consistent across compatible sections of a project.  Warning! Not suitable for children under 14 years.

Gears & motor pinions

39/40T RingGear, spare gear set for XV-02 TT-02

soon available again

This spare gear set brings the key drivetrain parts for direct coupling service into one focused pack. The set contains 2 direct coupling ring gears, one with 39 teeth and one with 40 teeth, plus 2 bevel pinion gears matched to those tooth counts. That layout gives a clear replacement route when the front direct coupling assembly needs the specified parts for continued use. The parts are named for Item 22047, the XV-02/TT-02 Front Direct Coupling Set with 39T, which places this set squarely in the drivetrain area rather than as a general hardware assortment. The 39T ring gear works with its dedicated bevel pinion gear, and the 40T ring gear works with its own matching pinion, so each pairing stays tied to the correct tooth count. The image-supported layout also makes the difference between the 2 ring gear options easy to identify during bench work, with each larger ring gear shown alongside its smaller mating pinion. Compatibility is stated for XV-02 and TT-02 chassis cars, making the set a practical choice for maintenance, repair, or keeping the correct replacement gears on hand between running sessions. On a workbench, the paired parts support straightforward selection when servicing the front direct coupling area of those chassis platforms.

Gears & motor pinions

39T Ring Gear XV-02/TT-02 GD, RC spare parts

soon available again

This RC spare parts set centers on a 39T ball differential ring gear and a 15T bevel pinion gear for XV-02 and TT-02 chassis cars. The matched gear pairing supports the differential drive path where torque changes direction through the bevel teeth, making it a focused replacement choice for drivetrain maintenance on compatible models. Alongside the 2 gears, the set also provides a differential case and a gasket. That combination covers the main housing and sealing elements around the gear area, so service work can address more than a single worn tooth or damaged gear face. The square center opening on the bevel pinion and the mounting pattern on the ring gear are shaped for their intended assembly points, while the gasket sits between housing parts where a clean fit matters. As a dedicated spare parts pack, the set is aimed at repair, rebuild, or routine drivetrain upkeep rather than general customization. On the bench, these parts suit planned maintenance after repeated running sessions or a targeted differential rebuild on an XV-02 or TT-02 chassis car. The separate components also make it easier to replace the affected drivetrain section with matching parts from one set instead of sourcing each piece individually.

Other spare parts & accessories

3mm Shim-Set, RC spacer set, 0.1/0.2/0.3mm

soon available again

The 3mm Shim-Set brings precise spacing control to RC car maintenance with 30 thin washers sized for 3 mm shafts. Each shim has a 3 mm inner diameter and a 5 mm outer diameter, making the set a practical choice for fine adjustment at suspension and other attachment points where excess movement can affect fit. Inside the set are 10 shims each in 0.1 mm, 0.2 mm and 0.3 mm thicknesses. That spread allows small, deliberate changes instead of forcing a single spacing value onto every location. On 3 mm suspension shafts, the shims can be placed to take up unwanted slack and refine how connected parts sit against one another. The ring format keeps the adjustment focused on the shaft position itself, which is useful when tuning linkage or suspension areas that react to very small dimensional changes. For workshop use, the set suits routine maintenance, chassis rebuilding and targeted setup corrections on many Tamiya RC cars. A builder can test one thickness, stack combinations where needed, and match the spacing to the exact attachment point rather than replacing larger components. The scope of delivery contains 1 spacer set with 30 pieces.  Warning! Not suitable for children under 14 years.

Screws & ball head screws

3x10mm Steel CS HexHead Screws, model hardware

soon available again

These 3x10mm Steel CS HexHead Screws are replacement model hardware for fastening points that require a countersunk head and a hex socket drive. The steel construction and fully threaded shafts support firm seating in compatible assemblies, while the black finish matches the clean, technical look often used in model components. Each screw uses a flat tapered head that sits flush when installed in the correct countersunk opening, which helps maintain proper part alignment on compatible builds and repairs. The 3x10mm size is the key fit detail for matching existing hardware, and the pack of 10 gives a ready supply for workshop drawers, routine servicing or targeted replacement of missing fasteners. The hex socket head is designed for secure tightening with the appropriate tool, making it suitable for controlled maintenance work where a precise fit matters. Used as spare hardware, these screws suit regular upkeep on compatible model vehicles and assemblies that call for this exact specification. They can be kept on hand for repair sessions, rebuilds or scheduled parts replacement, especially when worn fasteners need to be changed before they affect how connected parts stay in place.

Screws & ball head screws

3x10mm Steel Hex Head Screws, model hardware

soon available again

These 3x10 mm steel hex head screws bring precise fastening to model maintenance, repair and assembly work. The steel construction and threaded shaft support a firm hold in compatible mounting points, while the hex socket head is shaped for secure tool engagement during tightening and removal. With 10 matching screws in the pack, this hardware set suits routine workshop stock as well as targeted replacement jobs on frequently serviced models. The 3 mm diameter and 10 mm length provide a clearly defined format for builds and repairs that call for this exact screw size. The rounded button-style head sits neatly against mounted parts, and the fully threaded shaft is suited to fastening tasks where even thread contact matters across the full length. On the bench, these screws fit naturally into rebuilds, part swaps and general upkeep between running sessions. Keeping the correct fastener size close at hand helps avoid delays when worn or missing hardware needs to be replaced, and a matching 10-piece set makes it easier to maintain consistency across repeated service work.

Screws & ball head screws

3x10mm Tapping Screw, model hardware pack

soon available again

This hardware pack supplies 10 matching 3x10 mm tapping screws for model assembly, maintenance and parts replacement. The slotted pan-head format and threaded metal shaft give each fastener a clear mechanical role when compatible components need to be fixed in place with the correct size and thread style. The set is focused on workshop practicality rather than broad accessory claims. Each screw is shown as the same silver metal fastener, making the pack useful for replacing missing original hardware, refreshing worn fixings or keeping a consistent spare supply close to a build area. The 3x10 mm specification is the key detail here, because screw diameter and length determine fit across mounting points, brackets and compatible model sections. A 10-piece count also supports repeated use across more than one repair session instead of leaving a single replacement on hand. On the bench, this pack fits naturally into parts drawers, organiser boxes and tool trays where small hardware needs to stay sorted by size. It also works as a straightforward replenishment option for ongoing model servicing when matching screws are needed for routine rebuild or reassembly work.  Warning! Not suitable for children under 14 years.

Screws & ball head screws

3x12mm Steel Hex Head Screws, model hardware

soon available again

These 3x12mm steel hex head screws are small but essential model hardware for keeping compatible assemblies firmly fastened. The steel construction and hex head shape support a secure connection at fastening points where a precise fit matters, whether replacing worn screws or completing routine maintenance on a model car. Each screw measures 3x12mm and uses a fully threaded shaft, making the set useful wherever that exact size is required. The pack contains 10 matching screws, giving enough hardware for several mounting points or for keeping spares on hand in a workshop drawer or parts case. The silver metallic finish matches the straightforward function of workshop hardware and makes each screw easy to identify among other small components. On a repair bench, during a rebuild, or while refreshing frequently used running gear, replacement fasteners help keep compatible model sections properly attached. This set suits regular upkeep of model vehicles and other assemblies that use the same screw format, with the hex head allowing controlled tightening during fitting and replacement work.

Screws & ball head screws

3x14 mm Step Screw, spare part for TT-01 TA-01

soon available again

This spare part set supplies 5 step screws in a 3x14 mm format for TT-01 and TA-01 model applications. The defined dimensions support a direct hardware match where this specific fastener size is required, whether a missing screw needs replacing or an existing build needs the correct fitting part restored. Each screw has a stepped profile that combines a rounded head, a smooth shaft section and a ribbed lower section. That shape suits fastening points designed for this hardware style and helps maintain the intended connection between compatible model parts. With 5 matching screws in one pack, the set covers small repair jobs and routine workshop replenishment without mixing different sizes. On the bench, these screws suit rebuilds, maintenance sessions and parts sorting for ongoing chassis care. The compact 3x14 mm specification also makes the set practical as reserve hardware for TT-01 or TA-01 projects where the correct screw type needs to stay close at hand.  Warning! Not suitable for children under 14 years.

Screws & ball head screws

3x6mm HG Alu HH Screw, model screw set, blue

soon available again

The 3x6mm HG Alu HH Screw set brings precise fastening to detailed model work, with a Hi-Grade manufacturing process that helps each screw thread into place straight and true. The aluminum construction keeps the format focused on lightweight hardware, while the anodized blue finish adds a crisp visual accent on exposed mounting points. Each screw has a hex socket drive and a short 6 mm length suited to compact assembly areas where clean seating and accurate alignment matter. The pack contains 5 matching screws, making it useful for replacing worn hardware, refreshing visible fasteners or keeping identical spares ready for workshop use. The blue finish stands out clearly against neutral chassis parts, which can help when sorting hardware during maintenance. These screws are particularly suited to use with aluminum bulkheads and carbon fiber plates often found on TRF chassis machines. They also fit hobby tasks where a small, accurately made fastener is needed for secure mounting and a consistent finished look across the build.

Screws & ball head screws

3x8mm HG Alu HH Screw, model screw set, blue

soon available again

This set of 3x8 mm HG Alu HH Screws brings precise fastening to model building work where alignment matters. Each aluminum screw is made with a different manufacturing process than standard screws, so it threads into the hole straight and true. The anodized blue finish adds a clear visual match across the set and stands out neatly against surrounding chassis hardware. The pack contains 5 matching screws with hex socket heads and a countersunk profile. That head shape allows the screw to sit flush in a compatible recess, which helps keep adjoining parts evenly seated. The Hi-Grade specification is especially suited to aluminum bulkheads and carbon fiber plates often used in TRF chassis machines. In builds that combine these materials, a straighter screw path can help reduce skew during fastening and support a more exact fit between connected parts. These screws suit replacement work, hardware upgrades and fresh assembly on compatible model applications. On a workbench, the matched dimensions and finish make it easier to keep fixing points consistent across the same section of a chassis or plate layout.

Screws & ball head screws

3x8mm Steel CS HexHead Screws, model hardware

soon available again

These 3x8mm Steel CS HexHead Screws are model hardware for maintenance, repair and replacement work on compatible assemblies. The steel construction and countersunk head shape suit mounting points where the screw needs to sit flush with the surface, while the hex socket is designed for controlled installation with an Allen key style tool. The set contains 10 matching screws, making it useful for replacing lost fasteners or refreshing worn hardware in one go. Each screw combines a threaded shaft with a countersunk profile, a format often used where clean seating and secure fastening matter to the fit of surrounding parts. In regular workshop use, spare hardware like this helps keep a build mechanically consistent instead of mixing different screw types or sizes. The 3x8mm specification gives a clear reference when matching existing fittings on a compatible model. Kept in a parts box, the set is ready for routine servicing, rebuilds or targeted repairs after wear. It also suits bench work where a damaged fastener needs to be exchanged quickly so the assembly can return to proper running condition.

Screws & ball head screws

3x8mm Steel Hex Head Screws, model accessory

soon available again

These 3x8 mm steel hex head screws are a compact spare parts accessory for model maintenance, repair and ongoing workshop use. The steel construction provides the stated material specification, while the hex socket head is shaped for controlled tightening with the matching driver. In the pack, 10 matching screws are supplied for direct replacement where the same size and head type are required. The 3x8 mm measurement gives a clear reference for fit when replacing worn or missing hardware on compatible assemblies. Their machine screw form suits fastening points that rely on threaded metal hardware rather than clips or push pins. The internal hex drive helps apply torque through the center of the head, which is useful when working in small spaces common to model chassis and related components. As a spare parts set, the focus stays on restoring the original fastening function with the correct format rather than adapting a different screw type. In regular bench maintenance, a set of matching screws helps keep repairs consistent across repeated fastening points. For RC car servicing and rebuild work, timely replacement of worn hardware can help maintain proper assembly and keep compatible vehicles running as intended.

Screws & ball head screws

4 mm Flange Lock Nut, model hardware, 4 pcs.

soon available again

This set of 4 mm flange lock nuts brings secure fastening to model maintenance and mechanical assembly work. Each metal nut pairs a hex outer shape with a built-in flange and a nylon insert, creating a self-locking connection that helps threaded joints stay in place when vibration and repeated movement are part of the job. The flange base supports a broader contact area than a standard nut alone, which can be useful where mounted parts need even clamping across the surface. The nylon ring inside the thread adds friction as the nut is tightened onto a matching bolt, so the connection resists backing off during running, transport or repeated handling. With 4 pieces in the pack, the set suits small repairs, hardware replacement and keeping spare fasteners ready at the workbench. The silver metal finish also makes the parts easy to identify among mixed model hardware. Used on model vehicles, mechanical linkages or general hobby assemblies, these lock nuts fit naturally into routine service tasks where dependable retention matters. They are a practical choice for replacing missing hardware, refreshing older builds or stocking essential workshop spares for future adjustments.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

4-7mm Ground Clearance Gauge, setup tool

soon available again

This aluminium ground clearance gauge brings a precise reference to RC car setup work, with a stepped measuring range from 4 mm to 7 mm. The blue anodized body and clearly marked values make each height point easy to identify at the bench, helping setup changes stay consistent across repeated checks. The stepped form is designed for direct measurement against the underside of the chassis, so ride height can be checked against fixed increments rather than judged by eye. Markings at 4, 4.5, 4.8, 5, 5.2, 5.4, 5.6, 5.8, 6, 6.2, 6.5 and 7 mm provide multiple reference points for fine tuning. The machined aluminium construction gives the tool a solid, precise feel in hand, while the compact shape fits easily into a pit box, tool case or setup station. On a workbench before a run, the gauge supports quick confirmation after spring, damper or preload changes. Between sessions, it helps keep left and right setup checks aligned to the same measured clearance, making repeatable tuning work easier to track over time.

Spare parts for old cars

4mm Adjuster (3) Pink, model accessory

soon available again

This set of 3 pink 4 mm adjusters adds a clearly specified accessory part for model maintenance and replacement tasks where the exact diameter matters. The bright pink finish gives the small parts quick visual distinction in a parts tray, tool case or work area, helping separate them from similar hardware during ongoing setup work. The pack combines a defined 4 mm size with a 3-piece quantity, which supports matched use across repeated connection points or keeps spare parts ready for later service. For hobby benches that handle frequent tuning, rebuilds or part changes, a clearly marked adjuster size helps keep component selection consistent. The compact format also suits organised storage alongside other model hardware, where colour coding can speed up identification before fitting. Whether used during routine maintenance, a replacement job or a fresh parts sort, these adjusters fit naturally into detail-focused model work. The set works well as a small stock addition for builders who keep commonly used fittings on hand for future repairs and setup changes.

Screws & ball head screws

5.8 BCNuts for TRF Dampers, spare parts set

soon available again

These 5.8 BCNuts for TRF Dampers are steel spare parts made for precise damper maintenance, with slick metal plating that supports super smooth motion where the connector nut meets the assembly. In a suspension rebuild or a targeted refresh, that combination of steel construction and plated finish keeps the hardware focused on clean mechanical action. The set contains 8 ball connector nuts and is specified for use as spares for parts in Item 54878 Upgrade Set for TRF Super Short Big Bore Dampers. The 5.8 mm format gives a concrete match point when replacing worn damper hardware. As a dedicated maintenance part rather than a general accessory, the set suits workshop stock, scheduled servicing and selective replacement after repeated running sessions. The plated surface is the key working detail here, because it is stated to deliver smoother motion at the moving connection. On the bench, these nuts fit naturally into damper overhauls, suspension tuning sessions and parts-box replenishment for TRF-based builds. Keeping 8 matching spares on hand helps maintain consistent hardware across multiple service intervals and supports clean, focused rebuild work.  Warning! Not suitable for children under 14 years.

Screws & ball head screws

5.8x5mm Hex Ball Connector, model spare part

soon available again

The TRF421/X 5.8x5mm Hex Ball Connector is a dedicated model spare part for precise repair and maintenance work. Its specified 5.8 x 5 mm size gives a clear reference when an existing connector needs to be matched, helping keep a compatible assembly consistent at the fastening point where the part is used. With 2 connectors in the pack, this replacement set covers a paired hardware change without shifting into a mixed assortment of unrelated small parts. The hex ball connector format points to a compact mechanical role inside a model assembly, where correct dimensions matter for fit and connection. Because the data identifies this as a supplies and accessories part rather than a complete model, the focus stays on exact replacement and upkeep rather than on a full build. Batteries are not included. This kind of spare part fits naturally into routine bench maintenance, whether a worn connector is being exchanged during servicing or a damaged piece is being replaced to return a compatible model assembly to working order. The compact format also makes it practical to keep a matching pair on hand for planned repairs.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

Aluminum Reinforced Tape, model accessory, 50 mm

soon available again

This aluminum reinforced tape is made for model applications where high heat builds up close to the body shell. In gas operated vehicles, an exhaust pipe can run near the polycarbonate body, and the adhesive aluminum surface forms a heat resistant shield in that exposed area. The roll measures about 50 mm in width and 2 m in length, which gives flexible coverage for trimming sections to the required size. The reinforced construction suits placement along body areas that sit near hot exhaust routing, while the metallic surface is designed to handle heat exposure where direct proximity could otherwise mark or damage the polycarbonate. Scope of delivery: 1x aluminum tape reinforced. Used on RC vehicle body shells and similar model setups, the tape supports focused protection exactly where heat management matters most. It fits practical workshop tasks such as lining a body section near the pipe outlet, covering a local hot spot, or adding a barrier on an inner panel before the next run.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

Aluminum Spacer Set 5.5/3mm, model accessory

soon available again

This aluminum spacer set brings precise spacing control to model assemblies that use 3 mm screws. With a 3 mm inner diameter and 5.5 mm outer diameter, the rings sit neatly at screw-mounted connection points where height, clearance or part position needs fine adjustment. The blue and silver finish also makes the different pieces easy to sort on the workbench during setup changes. Inside the set are 6 spacer thicknesses: 0.5 mm, 1 mm, 1.5 mm, 2 mm, 2.5 mm and 3 mm, with 4 spacers supplied in each size. That spread supports small, measurable changes instead of broad jumps, which is useful when tuning the fit of linked parts or correcting alignment across paired mounting points. The reference application shown in the data places the spacers with suspension arm blocks and damper mounts, and the same dimensions also suit other assemblies built around 3 mm screw hardware. On a chassis build or maintenance session, the set supports repeatable adjustments when comparing one mounting position against another. Matching quantities across all 6 sizes help keep left and right sides consistent while leaving room to test different stack heights in mechanical layouts that need exact spacing.

Axes & drive shafts

Ball Diff. Joint right MB14, model spare part

soon available again

This Ball Diff. Joint right MB14 is a dedicated model spare part for compatible assemblies that use the specified Group C version. The named right-side format gives a clear replacement reference when an existing joint is worn, missing or needs to be exchanged during maintenance. The MB14 code identifies the joint type directly, which helps keep parts matching tied to the stated designation instead of relying on visual comparison alone. As a single replacement component, it suits repair tasks where only the affected connection point needs attention rather than a broader rebuild. The Group C note further narrows the intended application within the stated model context. That makes this spare part useful for keeping an existing build in running condition with the exact named joint format. In a workshop setting, small drivetrain replacements like this are often kept on hand for routine upkeep between running sessions or service intervals. The clearly stated right-hand version also helps separate it from mirrored or side-specific hardware when preparing parts for maintenance.

Spare parts for old cars

Battery Cover Side Bar Parts Set in Purple

soon available again

This purple C Parts set focuses on two clearly defined component groups: a battery cover and side bar sections. Supplied as moulded parts on a single sprue, it gives model builders a direct way to replace damaged pieces or complete a matching rebuild with the correct colour group already formed into the parts. The layout shown here includes long bar-shaped sections, smaller support pieces and a larger ribbed panel, all kept attached to the frame until separation. That format helps with part control on the workbench, especially when only one section of a model needs attention rather than a full rebuild. The designation C Parts identifies this as a specific spare set rather than a general accessory mix, which is useful when a repair calls for the right shape in the right area. The purple finish also matters in restoration work, where matching visible sections can be as important as replacing the broken piece itself. On the bench, this set suits careful maintenance, rebuild projects and the sorting of stored spare components by colour and part group. It also fits planned refresh work where a battery cover or side bar section needs to be replaced while keeping the rest of the model unchanged.

Spare parts for old cars

Body Mount D Parts, model spare set, purple

soon available again

This purple D Parts body mount set provides molded replacement components for a compatible model build and keeps the specified colour match consistent when a repair or refresh calls for the same parts group. The sprue format presents each piece on a single runner, with mirrored elements and small mechanical forms arranged for clear identification before removal. Visible shapes on the frame include 2 large ring-like bracket pieces, 2 small mirrored arm components, 2 cylindrical cup-like parts, 2 larger housing sections, several small connector-style pieces and 2 ball-ended rod parts. That mix points to a coordinated mechanical section rather than a single loose spare, which helps maintain matching geometry across linked mounting points. The injection-molded finish gives these small parts defined edges and uniform surfaces, useful when a build depends on clean seating and consistent alignment. As an unassembled spare-parts frame, the set suits planned maintenance, replacement of lost pieces or a colour-matched rebuild of the same section. On the bench, the runner format helps keep small components together until the fitting stage. In a repair session, the grouped layout makes it easier to compare paired left and right shapes, separate only the needed pieces and continue the build with the correct purple parts set for the intended assembly.

Shock absorbers & springs

Bruiser 4x4 D-Parts Bumper, RC spare parts

soon available again

The Bruiser 4x4 D-Parts Bumper set brings black molded bumper components to the Toyota 4x4 Pick-Up Bruiser RN36, replacing the white version supplied in kit 58519 with a darker visual match for custom builds. This set is aimed at builders who want to refresh the exterior appearance of the model while staying with parts made for the specified Bruiser platform. The scope of delivery contains 1 D-Parts set with 19 pieces. The parts are supplied as molded components for the bumper area, making the set useful for rebuilds, restoration work and planned visual changes on an existing assembly. The black finish changes the character of the front and rear details without requiring a switch to a different vehicle body or a non-matching accessory group. As a dedicated spare parts set, it focuses on the RN36 configuration named in the data rather than on general universal use. During a rebuild, the set can be used to replace original bumper parts that are missing or to shift the model toward a darker trim layout. It also suits a fresh assembly of kit 58519 when the goal is to move away from the standard white molded version and keep the bumper area visually consistent with other black details.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

C Parts R.Suspen./Gearb., RC spare parts sprue

soon available again

C Parts R.Suspen./Gearb. is a dedicated RC spare parts sprue for the 58618 Mt.Beetle, centered on rear suspension and gearbox components. The black molded frame groups the matching pieces in one place, giving repair and replacement work a clear starting point when an original section needs to be renewed. The sprue format keeps the individual parts attached until trimming, which helps with handling and identification during workshop preparation. Visible on the frame are larger housing-style sections, round cover-like pieces, bracket forms and smaller connector details, all molded as technical components rather than generic craft material. This format also helps confirm that the replacement shapes match the intended assembly area before fitting begins. For RC model maintenance, that matters most when gearbox and suspension sections need the correct geometry at their mounting points. Used during a rebuild, after wear, or when a damaged section needs to be exchanged, this spare parts frame supports a direct return to the specified model configuration. It fits naturally into a hobby bench setup focused on servicing an existing 58618 Mt.Beetle rather than starting a new full kit. Batteries are not included.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

C-Parts 1, CC-02 spare parts tree

soon available again

C-Parts 1 for the 58675 CC-02 is a spare parts tree built around technical replacement work on the CC-02 platform. The black molded runner groups multiple matching components in one set, making it easier to identify and remove the needed section during a repair, rebuild or maintenance session at the bench. Visible shapes on the sprue include suspension-style arms, steering or hub mount forms, housing sections, small mounting blocks and curved cover-like pieces. The layout keeps related parts attached until use, which helps with storage between service jobs and reduces the risk of mixing loose components. Two gear-housing style forms and several connection points indicate use around axle, steering and drivetrain assemblies, while the one-piece runner format supports orderly parts handling when a worn or damaged section needs replacement. This set suits hobby use where the goal is to restore fit and function with matching CC-02 parts rather than improvise with non-matching hardware. It works well as a workshop spare for ongoing maintenance, for replacing broken chassis-area pieces after running sessions, or for keeping a current build on schedule when one specific molded section is needed.

Shock absorbers & springs

C.V.A-Mini II Shock Seal Set, RC spare part

soon available again

The C.V.A-Mini II Shock seal set supplies 6 green damper sealing caps for suspension maintenance on selected RC chassis. As a replacement for 50519, this spare part supports rebuilds where original seals are worn, missing or being refreshed during routine workshop service. The set is standard equipment for the TT-02RR chassis, which makes it a direct match when restoring that platform to its original specification. It can also be used on TT-02, TT-02D and TT-02FT vehicles equipped with 50746, on TT-01 TYPE-E vehicles equipped with 53619, and on DT-03 and DT-03T vehicles equipped with 54567. The scope of delivery contains 6 damper sealing caps, giving a defined quantity for planned maintenance rather than a loose compatibility note. DT-02 XB cannot be used, and on DN-01 chassis this part cannot be combined with 54028. In workshop use, these caps suit scheduled damper service, replacement of lost parts, or preparation of a chassis before the next running session. The clearly stated chassis references help match the set to the correct suspension layout before installation and avoid ordering the wrong spare part.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

CC-02 J-Parts Body Mounts, chassis spare parts

soon available again

CC-02 J-Parts Body Mounts provide a direct spare-parts solution for the CC-02 chassis platform, combining body mounting pieces and suspension arm components in one matched set. The 2 included J Parts sprues support repair work that restores key connection points across the chassis while keeping the replacement process focused on the correct component group. The molded parts are supplied as black sprue frames, with mirrored left and right layouts that make the individual sections easy to identify before cutting and fitting. Multiple mounting bars, linkage-style pieces and bracket forms are arranged to serve structural positions within the chassis assembly. Because the set covers both front and rear areas, it suits maintenance jobs that go beyond a single broken mount and need a coordinated replacement across more than one section. Compatibility is stated for CC-02 chassis models, keeping the fit aligned with that platform rather than generic off-road frames. On the bench, this set supports routine restoration after wear, damage or a partial teardown of a CC-02 build. It also helps keep a running chassis ready for the next repair session by putting the relevant mounting and arm components in one dedicated spare-parts pack.

Axes & drive shafts

CC-02/CR-01 Propeller Shaft, RC spare part

soon available again

The CC-02/CR-01 Propeller Shaft is an RC spare part for compatible chassis, supplied as 1 drive shaft for drivetrain maintenance or replacement. Its dedicated fit for the CC-02 and CR-01 platforms keeps part selection straightforward when an existing build needs a fresh shaft in the driveline. The scope of delivery contains 1 drive shaft. The plastic construction matches the stated material specification, which matters when replacing a worn component with the correct version for the chassis layout already in use. As a focused spare part rather than a general accessory, it is intended for targeted service work on the transmission path between connected drivetrain components. The compact replacement format also makes it practical to keep on hand with workshop spares for regular RC maintenance. This shaft suits repair work after wear, as well as planned parts replacement during a rebuild of a CC-02 or CR-01 model. In a bench setup, it supports quick identification of the correct chassis application before installation into an existing driveline.  Warning! Not suitable for children under 14 years.

Spare parts for old cars

Chassis Grasshopper II, RC chassis spare part

soon available again

The Chassis Grasshopper II is a dedicated RC chassis spare part for repair, restoration and rebuild work on the matching model. Its molded tub layout forms the lower frame section, with raised side walls, internal compartments and a central platform that create the base structure for the vehicle's mechanical and electronic installation. Multiple mounting posts, precision-placed screw holes and molded cutouts define where compatible assemblies connect to the frame. Front and rear upright support sections extend the chassis layout for attaching further modules, while the recessed interior areas help organize the placement of installed components within the lower body. The black molded construction follows the familiar form of a model chassis base rather than a decorative shell, making it relevant wherever the original frame needs replacement after wear or damage. This part suits workshop use during maintenance, parts replacement and long-term model upkeep. It can serve as the starting point for bringing a Grasshopper II back into running condition, or as a fresh base for rebuilding an existing vehicle with correctly positioned mounting features already formed into the chassis.

Gears & motor pinions

Counter Gear 58043/58336 Hornet spare gear

soon available again

Counter Gear 58043/58336 Hornet is a dedicated replacement gear for compatible Tamiya model vehicle assemblies, built to restore the transmission function with the correct compound layout. The part combines 2 gear stages on one central hollow shaft, with a larger lower spur gear and a smaller upper gear formed as one piece for accurate placement in the drivetrain. The moulded white gear body is shaped for mechanical fit rather than decoration, and the 4 round holes in the larger gear face provide a clear visual identifier during servicing. As a spare part in the Models Supplies range, it is suited to maintenance work when a worn or damaged transmission gear needs to be replaced with the matching component. The integrated double-gear format supports the transfer of drive between meshing stages inside the compatible gearbox, where alignment and tooth engagement matter for consistent running. This gear belongs in the workshop, parts box or rebuild bench for compatible Hornet-related maintenance tasks. It can be fitted during transmission repair, routine overhaul or when bringing an older chassis back into running condition with the correct replacement component.

Other spare parts & accessories

DF-01 B-Parts Rear Gear Case Spare Parts

soon available again

The DF-01 B-Parts Rear Gear Case is a replacement sprue for the designated rear transmission housing area of a DF-01 model. The black injection-molded parts are supplied attached to the frame, which keeps each section identifiable before removal and helps separate the individual shapes during repair or rebuild work. Visible on the sprue are multiple structural components for the rear gear case section, including housing forms, circular and cross-shaped pieces, mounting holes and smaller connectors. This format supports a direct parts-based approach when an existing assembly needs the specific B Parts group rather than a full rebuild set. The molded layout also makes it easier to compare each section against the matching area of the vehicle during maintenance. Used as workshop spares or as a replacement during restoration of a DF-01 chassis, this set focuses on the rear gear case area named in the designation. It suits planned servicing, the exchange of worn sections, or the completion of an incomplete chassis where the original B Parts sprue is missing. Batteries are not included.  Warning! Not suitable for children under 14 years.

Shock absorbers & springs

DF-02 A-Parts Damper/Gear Cover Spare Parts

soon available again

DF-02 A-Parts Damper/Gear Cover is a replacement parts set for compatible RC model maintenance, centered on damper bridge and gear cover sections that support the mechanical layout of the DF-02 platform. The set arrives as 2 sprues with 15 pieces in total, providing fresh molded parts for repair work, rebuilds or planned stock for future servicing. The black molded components are supplied in sprue form, so each section stays connected and easy to identify before removal. Visible shapes include cover panels, mounting structures, linkage-style pieces and housing elements that suit technical replacement tasks where worn or damaged originals need to be exchanged. This format supports a clean workflow at the bench, because related parts remain organized until the exact section is needed. The set is aimed at restoring specific structural and protective functions rather than changing the model's configuration. In practical use, the parts can be fitted during drivetrain service, chassis repair or a general refresh of a well-used RC vehicle based on the DF-02 design. Kept as workshop stock, the 15-piece assortment helps avoid delays when a damaged bridge, cover or bracket needs a direct replacement to return the model to running condition.  Warning! Not suitable for children under 14 years.

Gears & motor pinions

DF-03 Bevel Gear Set, spare part for chassis

soon available again

The DF-03 Bevel Gear Set is a dedicated spare part pack for maintenance on the DF-03 chassis. With 5 included components in one set, it supports drivetrain service work where worn or damaged bevel gears need to be replaced with parts matched to the original platform. The pack contains 1 gear bevel gear set with 5 pieces, supplied as replacement components rather than as a universal transmission assortment. The moulded parts show the gear forms, centre holes and contact surfaces needed for installation in a compatible DF-03 layout. This makes the set useful for routine workshop stock, planned rebuilds or targeted repairs after heavy running. Because the parts are specified for the DF-03 chassis, compatibility stays clear during maintenance and parts selection. On the bench, the set fits naturally into gearbox servicing, drivetrain refreshes and rebuild work on an existing model. It can be kept alongside other running spares for the DF-03 platform, ready for the next transmission check or replacement job.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

DF-03 C-Parts Front Upright Steering Arm Set

soon available again

The DF-03 C-Parts Front Upright Steering Arm Set is a dedicated spare parts pack for the DF-03 chassis and focuses on the front steering area where precise component fit is essential. Supplied as 1 C parts tree with 6 parts, the set groups the matching pieces in one place for straightforward identification during maintenance, repair or a planned rebuild. The included components are shaped for the front upright and steering arm section, with mirrored larger pieces and smaller connecting elements that suit the geometry of this chassis area. That layout helps when replacing worn or damaged parts while keeping the original mounting positions and linkage arrangement consistent. The black and dark gray moulded finish also makes the individual forms and mounting holes easy to distinguish on the bench during parts sorting and assembly checks. This set suits workshop stock for an existing DF-03 vehicle, whether the goal is to replace a single damaged section or refresh the front end during a broader service. In a hobby room or trackside pit setup, having the correct C-Parts sprue ready can shorten downtime and keep a DF-03 chassis prepared for the next running session.  Warning! Not suitable for children under 14 years.

Gears & motor pinions

DF-03 Spur Gear Set, RC spare part for chassis

soon available again

The DF-03 Spur Gear Set is a dedicated RC spare part for the DF-03 chassis and supplies 4 replacement gears for transmission service. With 2 large gears, 1 medium gear and 1 small gear in the set, it covers several gear positions used in the drivetrain and gives rebuilds a direct parts match for this chassis platform. The gear shapes shown in the set use a classic spur gear layout, where straight-cut teeth mesh with neighbouring gears to pass motor drive through the transmission. That makes the set useful when worn teeth, damaged gear faces or general drivetrain use call for fresh components. The loose parts format also helps with selective replacement, since only the affected gear position needs to be changed rather than replacing unrelated transmission parts at the same time. Scope of delivery: 1x main gear set with 4 pieces. On the workbench, the set fits naturally into routine DF-03 servicing, rebuilds after heavy use, or parts storage for future repairs. Kept alongside other chassis spares, these gears support faster maintenance planning whenever a compatible DF-03 transmission needs attention.  Warning! Not suitable for children under 14 years.

RC spare parts

DT-02 C-Parts Damper Stay, RC spare parts

soon available again

The DT-02 C-Parts Damper Stay is a dedicated RC spare parts set for the DT-02 platform, intended for repair, maintenance and accurate replacement work. The molded black parts come on sprues and provide the defined shapes, mounting holes and braced sections needed where the original assembly calls for C-parts, keeping rebuild work focused on the correct fit rather than improvised substitutions. The set is suited to chassis servicing where damaged, worn or missing structural pieces need to be replaced with matching components. Visible upright brackets, cross-braced sections and reinforced connection points indicate parts designed to attach securely within the model's structure and support the placement of adjoining assemblies. Because the parts remain on sprues before installation, identification and preparation stay straightforward during workshop sorting. The molded finish and part geometry also make the set useful as a stock spare for future repairs on compatible DT-02 builds. On the bench, this kind of replacement set supports anything from a single damaged mount to a broader refresh of stressed chassis sections after repeated running. It also fits routine rebuilds where keeping the model close to its intended parts layout matters for clean assembly and dependable component placement.

Gears & motor pinions

DT-03/02 A-Parts, spare parts set for RC models

soon available again

DT-03/02 A-Parts 58344 supplies a dedicated replacement sprue for RC model maintenance, with black molded sections shaped for mechanical housing duties. The visible parts include cover and case pieces with circular openings, raised cylindrical forms and multiple mounting holes, giving repair work a direct match to the original layout. Ribbed structural detailing adds definition to the molded sections and helps distinguish each area during sorting and fitting. Because the parts remain attached to the runner, each section stays organized until removal, which supports careful preparation at the workbench. The set is identified as A Parts for 58344, making it a targeted choice when a rebuild calls for the correct molded frame sections rather than a generic hardware assortment. The glossy black finish matches the look typically used for enclosed chassis and gearbox areas. On a repair bench, the sprue format helps with checking shapes and positions before cutting each section free. It also suits keeping a dedicated replacement set on hand for future service work on a compatible build, especially when a damaged cover or casing section interrupts running sessions.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

DT-04 Freewheel Axles Long, RC spare part

soon available again

DT-04 Freewheel Axles Long is a dedicated RC spare part for compatible Tamiya model assemblies. The long axle format supports accurate replacement where the running gear requires this specific version, and the metal construction matches the technical character expected from a drivetrain hardware component. The visible design combines a threaded section, a smooth cylindrical shaft and a locking element, indicating a part made to seat mechanically in a defined mounting point rather than a general-purpose fastener. That combination matters during maintenance because the thread handles fastening while the shaft section aligns the part in use. The long specification distinguishes it from shorter axle variants and helps maintain the intended geometry of the matching DT-04 setup. As a single-purpose replacement component, it belongs in repair stock for existing builds that need the correct axle pattern rather than an improvised substitute. In workshop use, this kind of spare part supports routine servicing after wear, loss or damage to original hardware. It also fits planned rebuilds where a compatible chassis is being refreshed with the correct replacement parts, keeping the assembly focused on proper fit and function.  Warning! Not suitable for children under 14 years.

Shock absorbers & springs

DT-04/03 D-Parts, spare parts set, suspension sprue

soon available again

DT-04/03 D-Parts is a replacement sprue for the 58340 assembly group, supplied as 1 parts tree with multiple molded components kept together on the runner. The black injection-molded frame brings the needed D-section pieces into one clearly organized format for repair work, rebuilds or restoring an existing RC model to running condition. The layout shown on the sprue includes 2 large wishbone-style arms along with several smaller connectors, mounting blocks and a collar-shaped piece. Keeping the components attached to the runner helps preserve the full set until each section is cut free for use. Visible molded identifiers including D, 2, 3 and 4 provide a direct reference on the frame itself, which helps when sorting the pieces during maintenance. As a dedicated spare part rather than a universal accessory, this set is intended for the matching DT-04/03 application named in the data. On the workbench, the sprue supports targeted replacement after wear, impact or loss of an original section. It also fits rebuild sessions where a chassis needs fresh D-group components before the next run or display refresh.

Axes & drive shafts

F104/W/F103 Front Support Arm, Carbon Part

soon available again

This carbon-reinforced front support arm is specified for F104, F104W and F103 chassis applications and serves the front support area where an exact replacement part keeps a model's structure consistent. The dedicated fit makes it a practical choice when an existing arm shows wear, damage or loss during maintenance. Used in the front section of compatible chassis, the part supports orderly repairs and helps keep a build aligned with the original F104/W/F103 layout. The carbon-reinforced construction is the key material detail stated for this component, giving the part its defined specification within the range. Its naming also makes workshop identification more direct when several chassis families and spare parts are stored together. As a model supply rather than a complete kit, it is aimed at repair, upkeep and parts replacement on existing compatible cars. On the bench, this type of spare part fits naturally into rebuild sessions, front-end servicing and pre-run checks on F104, F104W or F103 models. It also works well as a stocked replacement for hobby rooms, pit boxes and parts drawers where the correct chassis-specific component saves time during ongoing maintenance.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

Fluorescent Antenna Pipes, RC model accessory

soon available again

These fluorescent antenna pipes add a clear visual marker to an RC model by lifting the antenna into bright orange, pink, green and yellow. The strong colours stand out well while driving, making the model easier to identify at a glance during fast laps, club sessions or side-by-side running. The pack contains 4 antenna pipes and is suited to colour changes, replacement use or keeping several builds ready with different antenna finishes. Each pipe is a simple add-on for the antenna position, where the bright tube creates a more visible reference point above the bodyshell. The included antenna caps complete the set and provide the small finishing parts needed for installation. As a compact tuning accessory, the set focuses on visibility and appearance rather than changing the drive system or chassis layout. On indoor tracks, outdoor tarmac or busy practice sessions, the fluorescent colours help the antenna remain easier to pick out against the background and among other running models. The different colour options also support matching the antenna to body graphics, race colours or workshop spares for ongoing RC maintenance.  Warning! Not suitable for children under 14 years.

Spare parts for old cars

Front Bumper Grasshopper Hornet RC Spare Part

soon available again

This front bumper for Grasshopper and Hornet is a dedicated RC spare part that replaces a damaged or missing front-end section with the correct shape for the model's original layout. The black moulded piece has a symmetrical frame with a central upper loop, tapered side arms and reinforced struts, creating a defined structural form at the nose of the vehicle. Three mounting holes are integrated into the lower section, with one in the centre and one on each side, so the part can be positioned at the front mounting area as intended for these models. The open braced geometry keeps the component focused on its structural role while preserving the recognisable outline shown on the original design. Rounded end sections on the outer arms complete the profile and give the part its characteristic front bumper shape. This replacement suits repair work after heavy running, workshop overhauls or the completion of an older chassis that is missing front hardware. It also fits restoration projects where the aim is to return a Grasshopper or Hornet to a more complete and correct front-end appearance with the proper dedicated bumper component.

Spare parts for old cars

Front Suspension Arm A Parts in Purple

soon available again

This front suspension arm A parts set in purple is a chassis component for model maintenance, repair and rebuild work. The part group is intended for the front suspension area, where correct fit and free movement matter for clean assembly and dependable operation. The purple colour makes the component easy to distinguish during parts sorting and workshop preparation. As a replacement set, it can be used when original suspension arms are worn, damaged or no longer moving as intended. Keeping the correct A parts on hand helps streamline service work and supports a tidy rebuild process when the front end is being refreshed. The defined part designation also helps match the component to the correct assembly step instead of relying on guesswork during maintenance. This component suits bench work, spare-parts storage and planned chassis servicing between running sessions. It also fits repair jobs where the front suspension section needs a like-for-like replacement part to bring the model back into working order.

Spare parts for old cars

Front Upright Pink (2), RC spare part pair

soon available again

Front Upright Pink (2) is a replacement RC spare part set with 2 mirrored front upright components, each carrying a silver metal axle spindle with a threaded tip. The shape shown in the part design supports wheel mounting at the outer front corner while linking the assembly to the steering and suspension points on the vehicle. Each piece combines a larger pivot hole at the top with 2 smaller mounting holes at the lower end, giving the front corner the attachment points needed for movement and alignment. The left and right layout is clearly mirrored, so the pair matches both sides rather than repeating the same side twice. The bright pink finish also makes the parts easy to separate from other chassis components during repair or rebuild work. Metal spindles are already attached, so the wheel mounting shaft and upright arrive as one assembly. This pair suits maintenance tasks where worn, bent or missing front corner hardware needs to be replaced with matching left and right parts. On the workbench, the mirrored forms, visible mounting holes and threaded axle ends make it easy to identify how each upright fits into the front steering assembly of a compatible RC model.

Gears & motor pinions

Gear Bag 58618 Mt.Beetle, RC spare gear set

soon available again

Gear Bag 58618 Mt.Beetle is a dedicated RC spare parts set for drivetrain maintenance on the specified Tamiya model. The set contains 2 moulded gears: a large spur gear with a central mounting hole and 3 triangular spoke cutouts, plus a compound gear that combines a large outer gear with a smaller integrated pinion. This layout supports a like-for-like replacement where the original geared transmission needs fresh parts. The visible tooth form and centre bores make the parts easy to identify during servicing, while the compound construction keeps the paired gear stages in one piece. That matters when a repair calls for the original gearing arrangement rather than a mixed substitute. The cream-coloured finish also helps distinguish these gears from other workshop parts during sorting and installation. As replacement components rather than a general accessory, they are aimed at keeping an existing RC vehicle in running order with the correct matching shapes. On the bench, the set fits naturally into routine maintenance, rebuilds after wear, or a parts box kept for model support. It also suits a targeted repair when inspection shows damaged teeth or a worn transmission gear in the Mt.Beetle assembly.  Warning! Not suitable for children under 14 years.

Gears & motor pinions

Gear Bag for 58106, RC spare gear set

soon available again

This gear bag for the 58106 Stadium Blitzer brings the key transmission elements together in one replacement set, with a large spur gear, a compound gear and a round mounting plate shaped for drivetrain service. The geared parts transfer rotation through meshing teeth, while the central shaft openings support correct placement on the relevant axle points during repair or rebuild work. The large gear uses a broad toothed outer ring for the main driven stage, while the compound gear combines 2 gear diameters in one part to pass motion onward at a different ratio inside the transmission. The round plate adds 3 upright locating pins and 3 smaller peripheral holes, giving the assembly defined reference points for positioning and fastening. The white moulded finish makes the separate shapes easy to distinguish on the bench when comparing worn parts against the replacements. As a model spare part, this set suits maintenance tasks that focus on restoring clean gear engagement and consistent rotational flow. On a workshop table, the 3 parts can be checked against the existing gearbox assembly before installation. During servicing of a 58106 Stadium Blitzer, the set supports targeted replacement of worn internal transmission components rather than changing unrelated parts.  Warning! Not suitable for children under 14 years.

Gears & motor pinions

Gear Bag for Gr. C Chassis, model spare parts

soon available again

This gear bag supplies drivetrain parts for Gr. C Chassis 70T/0.6 applications, centering the set around a large spur gear and matching support pieces for mechanical replacement work. The cream-white molded parts shown are arranged as individual components, making the set easy to identify when a chassis needs the correct transmission pieces returned to service. The visible contents consist of 1 large toothed gear, 2 flanged ribbed hub-like parts with hexagonal inner openings, and 3 small ring spacers. That combination points to power transfer, axle mounting and spacing functions within the matching chassis layout. The large gear uses a central round hole and 5 smaller mounting holes, while the ribbed parts add structure around the hex openings for placement on the intended mechanical interfaces. The 3 ring pieces support spacing and alignment where rotating parts need controlled positioning. Used during maintenance, rebuilds or parts replacement, this set suits bench work focused on restoring the original gear train arrangement of a compatible Gr. C Chassis model. It also serves as a practical reference set when comparing worn drivetrain pieces against fresh replacement components before installation.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

Gear Box Joint Bag, spare parts set for 58067

soon available again

This spare parts set supplies 2 gear box joints for 58067 and focuses on one specific maintenance task: restoring the connection point within the gearbox assembly with matching replacement components. The silver-colored metal finish and compact machined form give the set the technical character expected of a model drivetrain part. Each piece is shaped for mechanical engagement, with a knurled grip section that supports controlled handling during fitting and a slotted cup-like end designed to connect with the adjoining assembly. One joint is formed with a longer shaft, while the second is shorter, indicating 2 distinct matching parts within the set rather than duplicate loose hardware. That distinction matters during servicing, where the correct shape helps return the gearbox linkage to its intended layout. The set is supplied as a dedicated bag of replacement parts rather than a general-purpose fitting. On the workbench, these joints suit repair after wear, loss or disassembly, and they also support planned parts stocking for an existing 58067 model. For rebuilds, maintenance sessions or drivetrain refreshes, the set provides the named components needed for the specified reference without relying on improvised substitutes.

Spare parts for old cars

Gearbox B Parts, model spare parts, purple

soon available again

These purple gearbox B parts provide a direct source of molded replacement components for model maintenance and repair. The sprue layout keeps each piece together until removal, while the matching color helps maintain a consistent look on a build that uses purple gearbox sections. The set includes 2 large housing halves with tall cylindrical towers, multiple mounting holes and ribbed structural bracing. Smaller round parts sit in the center of the frame, including a gear- or pulley-like disc and 2 matching circular pieces with curved slot patterns. That combination gives a clear mechanical focus: enclosed casing sections supported by smaller shaped parts that fit the same gearbox area. The molded form is suited to replacing worn, missing or damaged sections without mixing unrelated shapes. On the bench, these parts support careful restoration work, rebuilds after wear, or the completion of an unfinished model that needs the correct gearbox section. The attached sprue format also helps with part handling and identification before trimming, test fitting and installation into the intended assembly.

Other spare parts & accessories

Heat Resistant Doublesided Tape, model accessory

soon available again

Heat Resistant Doublesided Tape (5) is a model accessory for mounting, repair and ongoing workshop use where an adhesive layer needs to stay in place during detailed build steps. The set contains 1 adhesive tape pack with 5 pieces, giving a clear supply for replacement or fresh application on compatible model tasks. This version is identified as a replacement for 500908078, which helps match it to an existing parts requirement without guesswork. The heat resistant specification makes it suitable for applications where standard adhesive material may not be the intended choice. As a model supply rather than a finished vehicle or kit, the focus stays on a practical consumable that supports fitting, securing and maintenance work across build benches and repair sessions. On an active project, the 5-piece format allows one strip to be used where needed while the remaining pieces stay ready for later adjustments, part changes or follow-up repairs. It fits naturally into model assembly, restoration and parts replacement work where accurate, purpose-made supplies keep the process moving.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

Heat Shrink Tubing Set, wire insulation, 100 mm

soon available again

This heat shrink tubing set brings a clean, practical finish to model wiring jobs by tightening around cables when heat is applied with a dryer or similar heat source. The tubing is intended to insulate wire runs such as motor and ESC cables, creating a close sleeve over exposed sections, joins or connection points where a tidy covering matters. The set contains 7 pieces in 3 diameters, giving a useful spread for different wiring tasks. There are 5 pieces in 5 mm diameter, plus 1 piece in 3 mm and 1 piece in 2 mm, and every section is cut to 100 mm length. That mix supports both broader cable coverage and narrower sleeves for smaller leads. The black finish keeps the look uniform across custom wiring layouts, repair work and replacement cable sections in model setups. In use, a section is placed over the wire before heating, then shrinks down to fit the cable more closely. This makes the set a handy bench supply for insulating soldered areas, refining cable routing and finishing electronic installations with a more orderly result on model and accessory work.  Warning! Not suitable for children under 14 years.

Spare parts for old cars

Hornet Purple chassis, RC spare part frame

soon available again

The Hornet Purple chassis is a replacement frame component for an RC model build, shaped as the main lower structure that carries compatible assemblies in one defined base. Its one-piece injection-molded form combines raised side walls, mounting holes, screw posts and rectangular cutouts, creating the fixed geometry needed when worn or damaged original parts need to be exchanged. Reinforcing ribs are molded directly into the frame to support the structure across the base, while the front fork-like mounting arms provide a dedicated connection point for matching chassis sections. The layout shown on the frame indicates space for internal hardware such as steering parts, axle mounts, motor installation points and an onboard battery area, but this spare part is supplied as the chassis component itself rather than as a complete vehicle assembly. The purple color matches the Hornet Purple designation and helps separate this frame from other workshop parts during maintenance. Used on the bench for repair, restoration or a fresh rebuild, the chassis gives compatible components a defined starting structure for reassembly. It suits replacement work where the original lower frame has cracked, worn at the mounting points or needs a color-matched swap within a Hornet Purple project.

Axes & drive shafts

K Parts Fr. Steering Arm, model spare part

soon available again

K Parts Fr. Steering Arm is a model spare part named for the 58618 Mt.Beetle designation and focused on the front steering area. It provides a direct replacement route when the original steering arm needs to be exchanged, helping return the linkage to its intended mechanical role within the model. The ShortDescription identifies this piece specifically as K Parts Fr. Steering Arm 58618 Mt.Beetle, which gives the part a clear maintenance context instead of leaving it as a generic workshop component. Its role sits in the front steering assembly, where steering input is carried through connected hardware during operation. Keeping the correct spare part on hand can simplify planned maintenance and the replacement of worn steering components. This listing states a spare part rather than a complete vehicle or full kit, so the focus stays on targeted repair of the steering section named in the data. In a model workshop, this kind of replacement piece fits routine service after running sessions or inspection of the front end. It also suits parts storage for builders who keep model-specific spares ready for maintenance tied to the 58618 Mt.Beetle designation.  Warning! Not suitable for children under 14 years.

Screws & ball head screws

Kugelpfanne kurz 5mm M3, model accessory, 8-pack

soon available again

Kugelpfanne kurz 5mm M3 L14mm is a model accessory set for compact linkage connections in compatible RC and scale builds. The set contains 8 identical ball sockets, each sized at 5 mm with an M3 thread and a length of 14 mm, giving a consistent format for repairs, maintenance work or fresh assembly tasks. The short layout suits installations where surrounding components leave little room for longer connectors. Used on compatible rods or linkages, the M3 thread supports a defined attachment point, while the ball socket form is designed for joints that need controlled articulation around a mounted ball end. Matching dimensions across all 8 pieces help keep geometry even when several connection points are updated at the same time. The black finish keeps the parts visually discreet within many chassis and linkage layouts. In workshop use, the set fits neatly into routine service jobs such as replacing worn rod ends or preparing spare hardware before a rebuild. During assembly of compatible steering or suspension linkages, the 5 mm socket size and 14 mm overall length provide clear reference dimensions when selecting the right connector for the available space.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

M-05 A-Parts, chassis spare parts for M-05

soon available again

The M-05 A-Parts chassis set is a dedicated spare parts pack for the M-05 Chassis and M-05 PRO Chassis. With 6 parts in the set, it supplies the defined chassis section needed when an existing build calls for replacement pieces or when a maintenance job reaches the structural housing area shown in the set. The molded parts form a matched component group rather than a mixed assortment of unrelated hardware. Visible screw holes, mounting bosses, recessed channels and ribbed reinforcement indicate the pack is intended for precise placement within the chassis structure. That focused layout helps keep servicing work aligned with the original M-05 platform, especially where a correct fit between adjoining chassis sections matters. The black molded finish also makes the parts easy to identify against other workshop materials during sorting and rebuild preparation. In a repair setting, the set can be kept with other M-05 running spares so the required chassis section is ready when wear or damage appears. It also suits planned maintenance on an M-05 or M-05 PRO chassis where the original A-Parts group needs to be renewed with the specified 6-piece replacement pack.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

M-08 Concept C Parts, RC spare parts, 2° uprights

soon available again

The M-08 Concept C Parts set restores a key suspension area on compatible chassis cars with replacement uprights, hub carriers and adapters arranged across 2 sprues. Built around hub carrier parts with a 2° caster angle, this set supports the intended front-end geometry while returning worn or crash-damaged assemblies to running condition. The sprues contain front and rear upright components, and the shared design with the M-07 Concept extends fit across more than one chassis family. Assembly information for the hub carriers shows left and right orientation, plus a 2.5 mm hole preparation step on part C5 before the C6 inserts are fitted. That detail matters when rebuilding the steering or axle mounting area, because the bearing seats, hinge-pin points and linkage mounting locations need the correct direction to align with the chassis hardware. On the bench, this set suits targeted repairs after bumps that affect the wheel mounting or suspension connection points. It also helps keep an M-07 or M-08 Concept car ready for the next maintenance session by replacing the exact corner components rather than changing a full chassis section.

Gears & motor pinions

M-08/M-07/TA06 Bevel Gear Diff. Set, RC spare part

soon available again

The M-08/M-07/TA06 Bevel Gear Diff. Set is an RC spare part for restoring the internal gear train of a compatible bevel gear differential. The set contains 2 bevel gear differential sets, with 2 larger bevel gears, 4 smaller bevel gears and 2 cross shafts shown in the included parts layout, giving the drivetrain the internal meshing parts needed to transfer rotation through the diff assembly. Inside the gearbox, the larger bevel gears and smaller pinion gears work together around the cross shafts to distribute drive across the axle while allowing differential action in corners. That mechanism matters when a worn or damaged gear train starts to affect smooth running, because the differential depends on accurate gear engagement at each contact point. Compatibility covers a wide range of chassis: TD4, TD2, DB01, FF-04 EVO, M-08 CONCEPT, M-07 CONCEPT, TA06 MS, TA06, TA06 PRO, TA05 Ver.II, TRF503, TRF211XM, TRF201XMW, XV-01, XV-01 PRO and XV-01T. For chassis-specific installation, TA05 Ver.II uses this set with 54312, DB01 uses it with 54329, and TD4 and TD2 use it with 54471. That makes the set a practical choice for maintenance, rebuilds and drivetrain refresh work on compatible touring, rally and buggy platforms where the differential internals need replacement.  Warning! Not suitable for children under 14 years.

Gears & motor pinions

M-08/M-07/TA06 Gear Diff. Cup Joint (2), RC spare part

soon available again

This spare part set supplies 2 cup joints for the gear differential on selected Tamiya chassis platforms, giving a precise replacement option when the original drivetrain connection parts need renewal. The set is listed as M-08/M-07/TA06 Gear Diff. Cup Joint (2) and is intended for compatible RC model maintenance rather than a universal fit. Compatibility in the data covers M-08 CONCEPT, M-07 CONCEPT, TA06, TA06 PRO, TA06 MS, FF-04 EVO, TD4, TD2, XV-01, XV-01 PRO and XV-01T chassis. That range helps keep one small service part relevant across several builds in the workshop, especially where the gear differential uses this cup joint format. The scope of delivery contains 2 driver cone diff. parts. For TD4 and TD2 chassis, the data also states use with 54471. In practice, this kind of replacement part suits routine drivetrain servicing, rebuilds after wear, or keeping compatible spares ready between running sessions. The 2-piece pack also supports paired replacement when both matching connection points are being refreshed on the same differential setup.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

M03/04 C-Parts, RC spare parts set for chassis

soon available again

The M03/04 C-Parts set is a dedicated RC spare parts set for M03/04 chassis, bringing suspension arm and body mount components together in one matching supply. With 2x C parts and 56 pieces in the scope of delivery, it supports targeted replacement work when specific mounting or linkage sections need to be renewed. The molded layout gathers multiple small mechanical shapes on coordinated runners, which helps keep related parts organized during workshop use. Curved arms, brackets, bushings, links and mounting sections can be identified and separated as needed for chassis service. This format is useful when an existing build needs original-style replacement parts rather than mixed universal hardware. The black finish blends naturally into many established M03/04 assemblies and keeps the visual look consistent after repair. On the bench, the set suits routine maintenance, rebuilds after heavy running, or setting aside matching spares for future service intervals. It also works well as a stock set for modelers who maintain more than one compatible chassis and want the relevant C runner parts ready when wear appears in suspension or body mounting areas.  Warning! Not suitable for children under 14 years.

Spare parts for old cars

M2 Screw 2x8mm, model spare screws, 10-pack

soon available again

This 10-pack of M2 screws in 2 x 8 mm format is built for precise fastening work on compatible model assemblies, with the stated application aimed at 3-pc front wheels. The compact size and machine-thread form suit small-scale hardware jobs where matching dimensions matter for a clean fit and dependable hold. Each screw uses a rounded pan head with a cross-slot drive, a combination that supports careful tool engagement during replacement or maintenance work. The silver-coloured metal finish keeps the pack easy to sort alongside other workshop hardware, while the uniform thread and head shape help maintain consistency across repeated fittings. As a dedicated spare-parts pack, it suits restocking after a lost fastener, preparing a rebuild bench, or keeping identical screws ready for later service. In practical use, the pack fits neatly into routine model upkeep, whether a front wheel is being reassembled, a worn screw is being exchanged, or matching hardware is needed to complete a repair without mixing sizes. The 10-piece count also leaves reserve screws available for future maintenance on the same compatible wheel setup.

Other spare parts & accessories

Micro Nozzle for CA Tire Cement, 10 Cannulas

soon available again

These Micro Nozzles for CA Tire Cement bring precise adhesive control to tire work with a very fine 0.5 to 0.3 mm tip. The narrow opening helps place glue in small contact areas on rubber tires, where a broad applicator can spread adhesive beyond the intended line. The nozzle works by capillary action, drawing the glue forward into the tip for controlled dispensing. After use, contact with air hardens the very end of the nozzle and creates a closed tip. For the next session, the hardened section is simply cut away, so the cannula is ready to guide adhesive again. This makes the nozzles a practical replacement part for regular bench use where clean, accurate glue placement matters. The set contains 10 cannulas, which supports repeated maintenance and setup sessions without interrupting work when a fresh tip is needed. On a hobby bench, during tire mounting, or while preparing replacement wheels, these nozzles help keep adhesive application neat and focused.  Warning! Not suitable for children under 14 years.

Gears & motor pinions

Pinion Gear 10T M0.8, model spare part, 23 mm

soon available again

This 10-tooth pinion gear with module 0.8 is a compact drivetrain spare part for model applications where the gearing specification needs to match the installed setup. The 23 mm format and metal construction give the part a precise mechanical presence suited to motor and transmission assemblies. The gear body shows a toothed drive section, a central mounting opening and a fastening screw for fixing the part onto a shaft. That combination points to direct use in a powered drivetrain, where the pinion transfers motor output into the next stage of the transmission. For maintenance work, the stated 10T and M0.8 specification matters as much as the physical size, because both values determine how the replacement part meshes with the existing gear train. The metallic finish and machined form also make the component easy to identify during workshop sorting and parts checks. In practical use, this spare part fits the moments when a model needs a like-for-like drivetrain replacement or a rebuild based on the same gear standard. It also suits the parts box for ongoing service work, where clearly specified gears help keep repair and setup tasks organised.  Warning! Not suitable for children under 14 years.

Shock absorbers & springs

Silicone Diff. Oil #5000, RC differential oil

soon available again

Silicone Diff. Oil #5000 is an RC differential oil for oil gear differentials, created to fine-tune how a model vehicle responds through corners. The higher viscosity supports a more stable feel in faster sections, making it a useful choice when a setup needs controlled action under higher-speed loads. The formula is based on silicone oil and comes in a 40 cc bottle, enough for about 22 uses in touring car different gears. The green color makes the grade easy to spot among workshop supplies, and the bottle format supports clean, measured application during routine maintenance. As a Hop-Up Option, it gives room to compare different viscosities and adjust differential behavior with a concrete setup change rather than broad trial and error. The data identifies this oil for model vehicle differentials, with kinematic viscosity listed at 5,000 mm2/s at 25 °C. On a workbench, it fits naturally into rebuilds, refresh intervals and handling experiments between runs. It also suits trackside tuning sessions where differential action is adjusted to match faster layouts or changing grip conditions.

Shock absorbers & springs

Silicone Oil #500, damper oil, 40 ml bottle

soon available again

Silicone Oil #500 is a tuning fluid for oil-filled dampers on model vehicles, giving a direct way to change damping feel through viscosity choice. The 40 ml bottle suits regular workshop use, and the green fluid sits in a compact format with a ribbed screw cap and narrow nozzle for measured application during shock service. The #500 grade corresponds to a kinematic viscosity of 500 mm2/s at 25 °C, placing it in the range used when damper action needs a firmer response than lower-number oils. Higher numbers indicate a harder viscosity, so this grade supports deliberate setup steps rather than guesswork. The formula is based on organopolysiloxanes, and the bottle is intended for all types of oil-filled damper. Compared with earlier set bottles in 35 ml and 20 ml sizes, the 40 ml fill gives more capacity for repeated rebuilds, fluid changes and routine maintenance. On the bench, the color-coded bottle helps separate this grade from other viscosities at a glance when several oils are stored together. During servicing, the nozzle shape supports careful filling of shock bodies, whether the task is a full refill before a run or a planned setup change between sessions.  Warning! Not suitable for children under 14 years.

Shock absorbers & springs

Spring Mount, model accessory, 2-piece set

soon available again

This spring mount set provides 2 matching replacement parts for model maintenance and parts planning. The designation names the component directly, making it a focused choice when a specific spring mount is needed rather than a general-purpose hardware substitute. The data identifies the set for 58035, which gives the accessory a clear reference point for compatible use. With 2 pieces in the pack, both matching parts can be kept together for repair work, restoration tasks, or spares storage alongside an existing model setup. The compact component format also suits organized workshop drawers, service boxes, or parts cases where small model accessories need to stay easy to sort and retrieve. This accessory fits naturally into routine upkeep when an existing build calls for the named mount part again. It also works well as a reserve set kept with other maintenance supplies, so a compatible model can return to service with the correct component on hand when replacement becomes necessary.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

Stadium Blitzer Right Upright, spare part

soon available again

The Stadium Blitzer Right Upright is a dedicated front replacement part for the model named in the data, built to restore the specific right-side mounting point in the front assembly. Its compact form combines a moulded white body with a metal shaft and a ball stud, giving the part the hard connection surfaces needed where linked components pivot and attach. The geometry shown for this upright focuses on mechanical fit rather than decoration. A circular mounting hole, a short threaded tip and the ball joint connection provide the key interfaces for installation into the surrounding front-end hardware. The part is supplied as 1 front right upright, which keeps the replacement focused on the exact side named in the specification. That makes it useful when wear, damage or loss affects one defined point in the assembly instead of a wider section. In workshop use, this kind of spare helps return a model to running condition by replacing the named upright with the same designated component type. It also suits parts storage for existing Stadium Blitzer maintenance, where keeping the correct front right spare on hand can shorten downtime between repair and the next run  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

TA-01/02 B-Parts Rear Gearcase, RC spare parts

soon available again

This TA-01/02 B-Parts rear gearcase set brings the rear transmission area back into service with red replacement components made for the TA-01 and TA-02 platform. The set contains 48 pieces, combining molded gearcase sections with the small hardware needed around the assembly, so repair work and parts replacement can stay focused on the correct fit. The included B parts cover the rear gearcase housing area rather than a general mixed assortment, which makes the set useful when a worn, damaged or missing section needs to be replaced with matching components. Alongside the larger red pieces, the contents include screws, metal pins, washers and bushings that support fastening, alignment and mounting within the gearbox assembly. The molded parts show multiple screw locations, shaped edges and dedicated seating points that suit a mechanical housing layout and help keep the rear section properly assembled. On the workbench, this set supports maintenance of an existing chassis, a period-correct rebuild, or the preparation of spare parts for future service. The red finish also keeps the replacement section visually consistent where the original build uses the same color-coded B parts, making it a practical choice for both running repairs and careful restoration work.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

TA-01/DF-01 Front Upright Red, spare part

soon available again

The TA-01/DF-01 Front Upright Red set supplies 2 front steering knuckles for model vehicle maintenance on all DF-01 and TA-01 chassis. Each molded part is shaped for the front end, with a large central opening and several connection points that support the upright's role within the steering and wheel assembly. The red finish also makes the pair easy to spot on the workbench when parts are sorted for a rebuild or replacement job. This spare part is aimed at keeping an existing chassis running with the correct front-end hardware rather than adapting it with guessed alternatives. The paired format covers both sides of the front axle in one pack, which helps when wear, damage or a colour change calls for a matched left-right setup. The mounting holes and arm sections are formed directly into each upright, so the surrounding steering linkage can be connected in the intended positions. That makes the set useful for routine servicing, restoration of an older chassis or preparation of a fresh rolling build based on DF-01 or TA-01 components. On the bench, the 2-piece set suits quick replacement work when the front suspension and steering area is already apart. In a longer rebuild, the red uprights also add a clear visual accent that stands out against neighbouring chassis parts while keeping compatibility focused on the specified DF-01 and TA-01 platforms.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

TA-01/DF-01/02 King Pin Lightweight (4), RC spare part

soon available again

The TA-01/DF-01/02 King Pin Lightweight (4) is a focused RC spare part set for steering and suspension maintenance on compatible chassis. With 4 matching knuckle bolts in a lightweight specification, the set supports clean replacement work where precise hardware fit matters and small differences in fastening parts affect how the assembly comes together. Each piece is a compact metal fastener with a threaded end, a smooth shaft section and a hex head, shaped for use in the knuckle area. That geometry supports accurate positioning during rebuilds and helps keep service work consistent across matching corners of the chassis. The set is supplied as 4 identical parts, which suits planned maintenance, repair after wear, or keeping spare hardware ready in the workshop. Compatibility is stated for G6-01, G6-01TR, GF-01, GF-01TR, GF-01CB, TT-02B, WR-02 and WR-02CB chassis. On the bench, this kind of dedicated hardware helps streamline rebuild sessions because the fit is tied to named chassis families rather than a generic screw assortment. It works well for replacing lost or worn steering fasteners during routine servicing, suspension refreshes or parts-bin restocking for frequently used RC platforms.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

TA-03 C-Parts Steering Arm C-Holder for TA-03F

soon available again

The TA-03 C-Parts Steering Arm C-Holder set is a dedicated spare parts pack for TA-03F and TA-03R chassis, focused on the steering and upright area where accurate fit matters most. The set delivers moulded replacement parts in black resin, making it a practical choice when worn, damaged or missing front-end components need to be brought back into service. The scope of delivery contains 1x C parts sprue with 14 pieces. Within that sprue are the shaped elements used around the steering arm and C-holder assembly, along with smaller related pieces that belong to the same moulded set. Keeping these parts together on one sprue helps match the original component shapes used on the chassis. The moulded format also supports clean parts selection during maintenance, whether the work involves replacing a single damaged section or refreshing several linked mounting points at once. On the bench, this set suits routine repair, careful restoration of an older TA-03 platform, or stocking essential spares for regular running sessions. It fits naturally into RC workshop use where chassis-specific parts save time and reduce guesswork during rebuilds. For compatible installation, the set is intended for TA-03F and TA-03R chassis.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

TA-03 G-Parts Gear-Set M0.6, chassis spare part

soon available again

The TA-03 G-Parts Gear-Set M0.6 is a dedicated spare part set for the TA-03 chassis, built around the exact platform reference needed for targeted transmission maintenance. The set supplies G-parts with an M0.6 gear specification, giving a clear match point when an existing drivetrain section needs replacement. Within workshop use, the TA-03 designation matters because it keeps parts selection tied to the intended chassis instead of relying on visual comparison alone. The included quantity is 1 G-Parts set with 6 pieces, which provides a defined contents count for service planning and parts checks before installation. The gear-set format also makes this a focused option for restoring the relevant transmission area rather than sourcing unrelated components. On the bench, this kind of chassis-specific spare part helps keep repair work orderly when a TA-03 build needs the correct G-section components back in place. It suits routine maintenance, replacement after wear, or completing a stored chassis with the proper M0.6 transmission parts ready for fitting.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

TA-03R A PARTS (BLACK)

soon available again

Other spare parts & accessories

TA-03R L-Parts Body Mount, chassis accessory set

soon available again

The TA-03R L-Parts Body Mount is a dedicated chassis accessory set for the TA-03R platform, supplying the specific mounting pieces needed when a build calls for the correct L parts. The black moulded components are arranged on 1 parts tree, so the full 6-part set stays organised until each piece is removed and fitted. The set is intended for model maintenance, replacement work or completion of an existing chassis configuration where matching body mount hardware matters. The parts tree format helps with part identification at the bench, while the moulded shapes and connection points support clean alignment during installation. Because this set is specified for the TA-03R chassis, it avoids guesswork around fit within that platform and keeps the build focused on the designated mounting layout. On a restoration project, a long-stored chassis can be brought back with the proper mounting pieces in place. During routine workshop upkeep, the set also serves as a practical source for replacing missing or damaged body mount components on a TA-03R model.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

TA-04/TA-05 King Pin Set, RC spare part, 4-piece

soon available again

The TA-04/TA-05 King Pin Set supplies 4 shaft screws for steering knuckle use, giving RC model maintenance a precise replacement set for a small but essential chassis connection. The metal screw format combines a cylindrical head, a smooth shoulder section and a threaded end, matching the kind of hardware used where controlled movement and secure fastening need to work together. This set is listed for TA-04 and TA-05 and is also specified for DF-03, M-06, M-06 PRO, M-05 ver.II PRO, M-05, M-05 PRO and MF-01X chassis. That broad compatibility helps when servicing several platforms from the same workshop stock. With 4 matching pieces in the pack, each screw shares the same form for consistent replacement across the intended mounting points. As a dedicated spare part rather than a generic fastener, the set is aimed at repair, upkeep and parts renewal on named chassis families. In workshop use, the screws can be kept with chassis-specific spares for routine rebuilds, steering knuckle service or the replacement of lost hardware after track sessions. The compact 4-piece format also suits tackle boxes and bench drawers where clearly assigned replacement parts save time during maintenance.  Warning! Not suitable for children under 14 years.

Screws & ball head screws

TA-05/TB Evo.V Suspension Balls, RC chassis parts

soon available again

TA-05/TB Evo.V 5 mm suspension balls are a focused RC chassis spare part for keeping suspension linkages moving as intended on a wide range of compatible Tamiya platforms. With 8 pieces in the set, this hardware suits replacement work, routine maintenance and planned setup changes where matching ball size matters across the suspension assembly. The stated compatibility reaches across TA06, TA06 PRO, TA06 MS, TB-03 VDS and TA05 ver.II chassis, and also covers FF-03, FF-03 PRO, TB-03, TB-04 and TB-04 PRO chassis with the specified option ranges 54064 to 54074 and, where stated, 54171 to 54175. M-07 CONCEPT and M-08 CONCEPT chassis are also named for use with 54760. That model-specific fit helps keep parts selection aligned with the chassis layout already in use, rather than relying on trial and error with general hardware. In workshop use, 5 mm suspension balls are the kind of small component that can make a setup refresh more straightforward when worn or missing hardware needs a direct replacement. The 8-piece count also supports keeping matching spares on hand for rebuilds, service intervals or chassis updates across several compatible on-road platforms.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

TA02/TA01 A-Parts Gearbox, RC spare parts

soon available again

This A-Parts gearbox sprue is made for TA02 and TA01 model applications and provides black replacement components for drivetrain and chassis-related assemblies. The molded runner format keeps the parts together until needed, making it easier to identify each section before separation and fitting during repair or rebuild work. The visible layout includes a central gearbox housing section, additional mounting structures, smaller hexagonal parts and other mechanical pieces formed in black injection-molded material. As a spare parts set, it is suited to replacing damaged or missing original sections where the matching TA02 or TA01 designation matters for fit within the intended assembly. The connected sprue format also helps keep small parts from being misplaced while a rebuild is in progress. This set fits naturally into workshop use for restoring an existing RC chassis, refreshing a stored model or keeping key replacement parts ready in a spares box. Where an older TA02 or TA01 build needs the correct gearbox-related sections rather than a universal substitute, this runner provides the designated parts group in one pack.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

TB Evo.IV/DF-03 Flang.Tube, spare part, 4.6 x 4.7 mm

soon available again

This spare part set supplies 2 collar tubes for selected Tamiya on-road and off-road chassis, using a compact 4.6 x 4.7 mm format that suits precise replacement work during maintenance or rebuilds. The designation TB Evo.IV/DF-03 Flang.Tube 4,6x4,7mm points directly to the specified tube size, helping match the part to the required location in a compatible chassis layout. The set is intended for a wide compatibility range that spans DF-03, FF-04 EVO, FF-03, FF-03 PRO, TA08 PRO, TA07 PRO, TA06 MS, TA06, TA06 PRO and TA05 ver.II. It also fits TB-Evo.7, TB-Evo. 6 MS, TB-Evo.6, TB-05 PRO, TB-04, TB-04 PRO, TB-03, TB-03 VDS, TRF419XR, TRF419X, TRF419, TT-02 TYPE-SR and TT-02 TYPE-S. That breadth makes the pair useful for keeping a parts box aligned with several chassis platforms rather than a single build only. In workshop use, a clearly specified tube size helps when replacing small hardware during servicing, tuning or restoring running condition after wear. The 2 included tubes can be kept as direct replacements for supported chassis or stored as matching spares for future maintenance sessions.  Warning! Not suitable for children under 14 years.

Gears & motor pinions

TB-03 Module Spur Gear 96T RC Drivetrain Part

soon available again

The TB-03 Module Spur Gear 96T is a dedicated RC drivetrain part for standard spur gear applications across a wide group of Tamiya chassis. Its 96-tooth layout supports gear ratio setup in combination with a pinion gear, making it a practical choice when a build calls for a specific transmission balance and clean meshing. The gear is specified for high efficiency, low drive losses and low noise, so power can move through the drivetrain with less wasted motion at the spur stage. The moulded design uses a large centre opening and multiple lightening holes around the gear face, reducing unnecessary mass while keeping the toothed outer ring ready for transmission duty. As a single main gear, it suits maintenance work, replacement of worn parts and gearing changes within an existing chassis setup. Compatibility is stated for F104PRO II, F104Ver.II PRO, F104W, F104, TB-03, TB-03 VDS, TB-04, TB-05, TRF103, TRF102 and TRF101 chassis. In workshop use, the gear fits naturally into rebuilds, race-day spares boxes and planned ratio changes where a 96T spur is the required specification. The scope of delivery contains 1 main gear.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

TL-01/B A-Parts Chassis Spare Parts Set

soon available again

The TL-01/B A-Parts Chassis set provides a dedicated replacement pack for the TL017B chassis and focuses on the structural section where accurate mounting geometry matters most. Supplied as 3 parts, the set supports repair and rebuild work with components shaped for the original layout. The molded pieces show the technical detailing expected in a chassis section: multiple screw holes, reinforced ribbing, circular bearing seats and shaped cutouts that leave space for adjoining assemblies. This kind of geometry matters during maintenance because the chassis section does more than fill space; it positions connected parts at the intended points and preserves the layout of the model. As a model accessory rather than a complete kit, this set is aimed at replacing a specific area instead of reworking the whole vehicle. On the bench, the set suits planned servicing after wear, damage or a stripped mounting point has made the original section unusable. It also fits ongoing restoration work on a TL-01/B based model where the correct A-parts are needed to return the chassis structure to its intended form.  Warning! Not suitable for children under 14 years.

Shock absorbers & springs

Touring Car Tuned Spring Short, chassis spring set

soon available again

The Touring Car Tuned Spring Short set adds a focused suspension tuning option for compatible on-road chassis. With 6 springs in the pack and 3 distinct rates, it supports more precise handling changes than a single-rate replacement and keeps setup work clear through fluorescent color coding. The set contains 2 soft, 2 medium and 2 hard short springs, so front and rear combinations can be matched without mixing rates. Soft springs are marked in fluorescent red, medium in fluorescent yellow and hard in fluorescent blue, making each pair easy to identify during setup changes. The short format covers about half the gap between OP163 and OP440, which adds a useful intermediate step when refining corner response and chassis balance. Compatibility is stated for M-08 CONCEPT, M-07 CONCEPT, M-06, M-06 PRO, M-05 ver.II PRO, M-05, M-05 PRO and MF-01X chassis. At the workbench, the 3-rate layout helps compare suspension changes methodically instead of swapping between wider setup steps. On a running chassis, the paired springs support consistent front or rear installation while leaving room to test different combinations across multiple sessions.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

TRF Cross Joint for D-Kardan, spare parts set

soon available again

The TRF Cross Joint for D-Kardan is a spare parts set for Double Cardan Universal shafts, built to restore the small drivetrain parts that wear through repeated running. By replacing the cross star promptly, compatible chassis can maintain the precise movement needed at the shaft assembly, especially where smooth transfer through the drivetrain matters during regular use. The set contains 4 cross joints, 4 axle rings and 4 shafts for service work on the Double Cardan Universal assembly. Compatibility spans a broad group of chassis named in the data, including TA07 MS, TA07 MSX, TA06 MS, FF-04 EVO, TB-Evo.6, TB-Evo.7, TRF419, TRF419X, TRF419XR, TRF420 and TRF420X. Further listed fits include TA07 PRO, TA08 PRO, TA06, TA06 PRO, FF-03, FF-03 PRO, TB-03, TB-03 VDS, TB-04, TB-04 PRO and TB-05 PRO, with certain applications specified for use with 42216, 42300, 42312, 42218, 42219, 42220 or 42239. This kind of replacement set suits routine workshop maintenance, rebuilds after heavy track sessions and keeping compatible chassis ready with matching service parts on hand. The compact hardware format also makes it practical to store alongside drivetrain spares for quick swaps when a worn cross joint starts to affect running feel.

Shock absorbers & springs

TRF Damper L.Friction V Part (2), damper parts

soon available again

TRF Damper L.Friction V Part (2) is a replacement and tuning set for Tamiya damper systems, built to keep suspension movement smooth and controlled on compatible chassis. The set contains 22 damper V-parts and uses a molybdenum compound that supports increased durability while reducing friction in moving damper sections. This set is designed for the TA05 chassis and for current touring car platforms that use TRF Low Friction dampers. The listed compatibility also extends across a wide range of chassis families when combined with the specified damper sets: 53571 for XV-01, XV-01T, XV-01 PRO, TA06, TA06 PRO, TA06 MS, FF-03, FF-03 PRO, TB-03, TA05 ver.II, TT-02, TT-02D, TT-02 TYPE-S, TT-02 TYPE-SR, TT-01 TYPE-E, TT-01D TYPE-E and TT-02RR; 53901 for F103GT, F104 and F104W; 53926 for DF-03, DB01 and DB02; and 54993 for TD4 and TD2. M-08 CONCEPT requires 42273, 42355 or 54000, while M-07 CONCEPT requires 42102, 42273, 42354, 42355 or 54000. In workshop use, these parts support routine damper rebuilds, replacement of worn components and careful chassis maintenance before the next session. They suit racers and builders who tune suspension response through compatible TRF damper assemblies rather than replacing the full damper set.  Warning! Not suitable for children under 14 years.

Shock absorbers & springs

TRF Damper Oil Seal, RC spare part, 4-piece set

soon available again

The TRF Damper Oil Seal set is a focused RC spare part for servicing Tamiya TRF touring car dampers. Each seal sits in the damper assembly as the barrier around the moving shaft, helping the oil-filled unit keep its intended damping action during setup and running. With 4 matching seals in the pack, the set supports planned maintenance as well as replacement of worn sealing parts. Fitment reaches across a broad group of Tamiya chassis platforms. The list includes XV-01, XV-01T, TA07 MS, TA07 MSX, TA06, FF-03, TB-03, TA05-Ver.II, TC-01, TT-02, TT-02D, TT-02 TYPE-S, TT-02 TYPE-SR, TT-01 TYPE-E, TT-01D TYPE-E, TT-02RR and TT-02FT when used with 53571. It also covers M-07 CONCEPT with 42102, 42273 or 54000, F103GT, F104 and F104W with 53901, plus DF-03, DB01 and DB02 with 53926. In workshop use, these seals suit routine damper rebuilds, chassis refreshes and suspension tuning sessions where consistent oil control matters. The product data also notes a racer tip: adding O-rings or foam bushings between the rubber oil seal and the damper cap can create different damping effects.  Warning! Not suitable for children under 14 years.

Shock absorbers & springs

TRF Damper X-Rings, damper parts for silicone oil

soon available again

The TRF Damper X-Rings 50DM for silicone oil bring a focused upgrade to oil damper maintenance, using an X-shaped cross-section that seals more effectively than a standard circular O-ring. In the workshop, that design supports a cleaner damper build and helps keep the oil where it belongs during repeated use. Each set contains 8 purple damper X-rings made from special silicone material. That material is stated to maintain its shape for longer, so the sealing edge stays more consistent over time inside the damper. The specified hardness is 50, giving this version a clear place in suspension tuning and rebuild work. Item 42214 is designed for silicone damper oil, while the related mineral-oil version is a different part. The rings are used for oil dampers and are described as a match for Aeration Dampers such as the Buggy HL Aeration Damper Set and the Buggy Aeration Oil Filled Damper Set. For maintenance on compatible chassis, the set is also stated for T3-01 use with 54839. Kept in a pit box or parts drawer, the 8-ring pack suits routine damper refreshes, replacing worn seals, or preparing a fresh damper setup before the next run.

Axes & drive shafts

TRF Joint Case for D-Cardan, model spare parts

soon available again

The TRF Joint Case for D-Cardan is a dedicated spare parts set for model drivetrain maintenance, supplied as 2 matching joint cases. The cylindrical metal pieces are shaped for the specific geometry of a D-Cardan assembly, with drilled side holes and ring grooves near both ends visible on each part. Their compact machined form supports accurate placement at the intended connection point, where the case shape matters for fit and movement within the surrounding mechanical setup. As replacement components rather than general workshop hardware, they are suited to restoring the original layout of a worn or damaged assembly. The 2-piece format also provides the matching pair needed when both sides of the mechanism use the same part. In workshop use, these spare parts fit naturally into routine servicing, rebuilds, or targeted repairs on an existing model. They are especially useful when a drivetrain is being refreshed after wear, or when a D-Cardan system needs the correct case geometry to return a mechanical assembly to proper operating condition.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

TRF416 Front Upright, RC spare part for chassis

soon available again

The TRF416 C Parts Front Upright set supplies 2 replacement parts for the front end of selected Tamiya chassis, with each molded piece formed around a large circular hub opening and several mounting holes for the surrounding running gear. This layout supports a clean swap when the original upright has taken wear or impact damage and the steering assembly needs the correct part shape again. The set is intended for a broad range of on-road platforms, covering FF-04 EVO, FF-03, FF-03 PRO, TA07 MS, TA07 PRO, TA06 MS, TA06, TA06 PRO, TA05 ver.II, TB-Evo.7, TB-Evo.6 MS, TB-Evo.6, TB-05 PRO, TB-04, TB-04 PRO, TB-03, TB-03 VDS, TRF419XR, TRF419X, TRF419, and TT-02 TYPE-S. The paired format suits left and right front positions, and the molded construction keeps the mounting points and hub area consistent with the original chassis design. For workshop upkeep, that means less guesswork when replacing a damaged corner and restoring the front suspension layout. Kept in a pit box or parts drawer, these uprights are useful for routine servicing before club racing, for rebuilding a stored chassis, or for replacing a stressed front corner after contact on an indoor or outdoor track. The compact 2-piece set focuses on one critical front-end component rather than a mixed hardware assortment, making it easier to match the needed part to the repair.

Shock absorbers & springs

TRF420 B-Parts Bumper, spare part for chassis

soon available again

TRF420 B-Parts Bumper is a dedicated spare set for TRF420 chassis cars, built to put a damaged front-end component back into service with the correct replacement part for this platform. The set contains 1 bumper and matching B-parts on a moulded sprue, giving a direct route to repair work after contact on the track. The bumper design has been revised so it does not affect the roll characteristics of the chassis, which matters when a car is already tuned around a known handling balance. New body mounts with a 2 mm offset add another adjustment point by allowing different attachment positions. That layout supports body mount relocation to fine-tune the center of balance, using the replacement parts not only for repair but also for setup correction. The moulded format keeps the parts grouped together before removal from the sprue for fitting. In workshop use, this spare set suits routine maintenance between race meetings, rebuilds after heavy contact, or a chassis refresh before the next setup session. Kept in a pit box or parts case, it gives TRF420 owners the exact bumper-related pieces needed for a platform-specific replacement instead of adapting a general component.

Axes & drive shafts

TRF420 D-Parts Sus Arms, chassis spare parts

soon available again

The TRF420 D-Parts Sus Arms are spare suspension arm parts developed for the TRF420 racing chassis kit. The set contains 2 molded parts, shaped for suspension duty and built in carbon fiber-reinforced material to give the arm structure a rigid base where the chassis loads the suspension through corners, braking and acceleration. A revised damper mounting design uses aluminum inserts at the attachment point. By fitting different inserts, sold separately, the lever ratio can be changed across 3 different setups, which adds a clear tuning function to the replacement parts rather than limiting them to like-for-like maintenance. The rear arm layout also carries a 3 mm offset to the rear. That geometry allows use of the shorter TRF420 lower deck while keeping the same wheelbase, and it is specified to increase rear traction. These parts are intended for use with 3 mm diameter shafts. Compatibility is stated for TRF420, and also for TRF419, TA07 and TB-05 PRO chassis cars, with a note that the rear arm offset differs from standard kit parts on the marked chassis and wheelbase adjustment with spacers is required. This makes the set relevant both for TRF420 upkeep and for chassis tuning work across compatible platforms.

Other spare parts & accessories

TT-01 Bathtub Chassis, chassis part, tub frame

soon available again

The TT-01 Bathtub Chassis is a chassis part for TT-01 builds, formed as a black molded tub frame that creates the main lower section of the model. Its one-piece layout brings the mounting areas, compartment sections and structural walls together in a single base, giving the assembly a defined foundation for the rest of the running components. The molded construction shows multiple screw points, reinforcing ribs and raised posts that help position attached parts in the intended locations. Formed front and rear mounting areas support the chassis layout at both ends, while the central cross brace adds another structural element within the frame. The internal shape also provides dedicated recessed sections for component placement, which helps keep the build organized during repair or reassembly. As a spare part, this chassis is suited to replacing a damaged lower frame while preserving compatibility with the TT-01 platform. On the workbench, the tub frame serves as the starting structure for a rebuild, with the molded sections helping sort where major assemblies sit within the chassis. It also fits parts stock for ongoing TT-01 maintenance, where a fresh lower frame can return a used model to a clean, correctly based configuration.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

Wheel Axle (2), RC spare part, 35 mm metal

soon available again

This spare parts set supplies 2 metal wheel axles for compatible RC chassis, with each axle measuring 35 mm. The specified length gives a clear reference for repair, replacement and parts matching when worn or damaged running gear needs the correct component. Compatibility is stated for TT-01R, DF03, TNS and TL01 chassis, making the set a direct choice for those platforms rather than a general axle with unspecified fit. The metal construction suits a mechanical role where the axle connects wheel-related hardware inside the chassis assembly. The pair format supports side-by-side replacement when both matching parts are changed together. The source data also notes further chassis references including DF-03, DT-02, M-06, M-06 PRO, M-05 ver.II PRO, M-05 and M-05 PRO, while XB models are excluded. In workshop use, a defined 35 mm axle length helps when checking an existing build against the replacement part before installation. For routine servicing, rebuilds or wear-related swaps on supported RC cars, this 2-piece set keeps the focus on the exact axle type needed for the stated chassis families.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

WR-02CB Alum. Skid Guard, RC chassis accessory

soon available again

The WR-02CB Alum. Skid Guard is a front underside hop-up part for big wheel chassis models, built as a one-piece aluminum replacement for the kit-standard shaft-holding part. Its 30 degree skid angle changes how the front of the chassis meets rough ground, helping the model ride up and over bumps instead of digging in when the nose touches first. This accessory installs in place of F4 or M8, depending on chassis type, at the point that holds the U-shaped shaft. The aluminum construction adds a light yet rigid contact section at a high-impact area under the front end. Two 3x10 mm screws are included for attachment, and the guard is designed to work together with the front bumper parts already supplied with the chassis. That layout keeps the upgrade focused on the lower front contact zone rather than changing the surrounding suspension structure. Compatibility covers WR-02, WR-02C, WR-02G, GF-01, G6-01 and WR-02CB chassis models. On loose dirt, uneven tracks and rough outdoor surfaces, the skid guard gives the front underside a smoother leading edge where scrapes and knocks are most likely to happen. It suits builders refining a running chassis with targeted protection at the exact point where the model first meets the terrain.

Shock absorbers & springs

XV-01 B Parts Bumper Set for RC Chassis

soon available again

The XV-01 B Parts Bumper set is a chassis spare for keeping compatible RC models in running condition with the correct replacement section. The pack contains 8 pieces and is intended for the B parts area, covering bumper-related components used on supported platforms. This spare parts set matches the XV-01 chassis, XV-01 PRO chassis, XV-01T chassis and FF-04 EVO chassis. As a dedicated replacement group rather than a mixed hardware assortment, it helps maintain the original fit of the specified section when damaged parts need to be exchanged. The black molded parts are arranged as one coordinated sprue set, which keeps the relevant pieces together for workshop storage and parts identification. This format also makes it easier to match the replacement section to the required chassis area before installation. The set suits routine maintenance, repair after contact, or rebuilding an existing model with fresh chassis components in the correct B grouping. It can also serve as a shelf spare for owners running several compatible platforms, where having the matching section ready helps shorten downtime between workshop sessions and track use.  Warning! Not suitable for children under 14 years.

Shock absorbers & springs

XV-01 Dirt Spring Set, RC tuning springs H/M/S

soon available again

The XV-01 Dirt Spring Set H/M/S adds a focused suspension tuning option to compatible RC touring car setups. With 6 metal coil springs in 3 different rates, the set provides 2 hard, 2 medium and 2 soft springs, so matched pairs are ready for damper changes on one axle. The springs are made for chassis equipped with TRF dampers or CVA shock units, which keeps the upgrade tied to established suspension hardware rather than a full conversion. Changing spring rate alters how the suspension compresses and returns under load, making this set useful when refining response for loose dirt sections, mixed-grip surfaces or a more settled feel through repeated laps. The H/M/S layout keeps the choice clear during setup work, and the paired format supports balanced installation side to side. In workshop use, the set suits routine maintenance, replacement of worn springs or a fresh suspension baseline before the next run. On the track, different rates can be tested back to back on the same chassis to compare steering feel, weight transfer and overall composure with the existing damper system.

Shock absorbers & springs

XV-01 J Parts Damper Stays RC Spare Parts

soon available again

The XV-01 J Parts Damper Stays set supplies 14 replacement components for the XV-01 chassis range and gives RC model maintenance a clear, model-specific fit. Intended for the XV-01 chassis, XV-01 PRO chassis and XV-01T chassis, the set supports repair work where original mounting parts need to be renewed after use, disassembly or damage. Within an RC chassis, damper stays and related structural pieces help position suspension hardware and keep mounting points aligned with the rest of the assembly. A dedicated parts set like this keeps rebuilds focused on the exact chassis family named in the data, rather than relying on mixed universal spares. The black molded components are suited to replacing missing or worn pieces while preserving the intended layout of the compatible platform. Scope of delivery: 1x J-Parts set with 14 pieces. This kind of spare set fits naturally into bench work, whether a chassis is being refreshed between runs, repaired after contact, or rebuilt from sorted assemblies. For owners of the XV-01, XV-01 PRO or XV-01T platform, the named compatibility helps streamline parts selection and keeps maintenance centered on the correct vehicle architecture.  Warning! Not suitable for children under 14 years.

Other spare parts & accessories

XV-01 NN Parts Spacers 2, chassis spare parts

soon available again

XV-01 NN Parts Spacers 2 is a chassis spare parts set built around the small components that keep RC model assemblies aligned and moving as intended. With 90 NN parts in the pack, it supports repair benches, routine maintenance and parts replacement when original spacers are missing, worn or needed again during a rebuild. The set is specified for the XV-01, XV-01 PRO, XV-01T and FF-04 EVO chassis, so the fit is tied to named platforms rather than a vague universal claim. Spacer parts sit between connected components, help maintain the intended distance at mounting points and support clean assembly where shafts, joints or linked sections need the correct separation. Keeping a dedicated pack of these small parts on hand can prevent a chassis job from stalling over a single missing piece. The scope of delivery contains 1 set of NN parts with 90 pieces. On the workbench, this set suits planned servicing as well as targeted replacement after teardown. It also helps when an existing chassis is being refreshed and the original spacing parts need to be sorted back into the correct positions during reassembly.  Warning! Not suitable for children under 14 years.

Shock absorbers & springs

XV-02/TD2 Alum. BigBore Fr. Damper (2), RC damper set

soon available again

The XV-02/TD2 Alum. BigBore Fr. Damper set adds a focused front suspension upgrade with 2 aluminum aeration dampers built for oil-filled operation. Big bore cylinders increase internal oil capacity, and the aeration design works by moving the piston through oil while air is bled during filling, supporting a more consistent damping feel through repeated runs. Each damper is built around a 40.7 mm piston rod and uses sealing components including 6.5 mm, 11.5 mm and 14 mm O-rings, plus 3 mm red O-rings and shims in the rod guide section. Two piston types are supplied, with 1.6 mm and 1.7 mm holes, so the internal flow characteristic can be selected during assembly. The set also includes 3 x 18 mm, 3 x 15 mm and 3 x 12 mm screws, 5 mm ball connector nuts, 3 x 2 mm and 3 x 1 mm spacers for adjustment, and 2 x 5 mm cap screws. Damper oil and coil springs are required separately. During setup, oil is filled into the cylinder, the piston is moved slowly to release air bubbles, and the cap is fitted before excess oil and air are removed. Spacers can then be used to alter rebound stroke or mounting position, making this set useful for rebuild work, maintenance, or front-end tuning on compatible RC chassis.  Warning! Not suitable for children under 14 years.

Axes & drive shafts

XV-02/TRF Axle Shaft, model accessory, D-Cardan

soon available again

The XV-02/TRF Axle Shaft for D-Cardan is a dedicated model accessory for RC vehicle maintenance, supplied as a 2-piece set for the specified drivetrain layout. Each shaft is shaped for the XV-02/TRF platform and the D-Cardan system, giving builders a direct route to replacing worn running gear parts with the correct component type. The close-coupled shaft design points to a mechanical role where accurate fit and clean movement matter inside the drivetrain. The parts shown feature a metal body, a threaded end section, a side hole in the shaft body and a pivoting joint-style end, all of which indicate a component made for mounted, moving connections rather than general hardware use. That makes this set relevant for repair work, scheduled maintenance or keeping a chassis configuration consistent after heavy running sessions. On the bench, a matched pair helps keep left and right side service work aligned when the D-Cardan assembly needs attention. In an RC workshop setup, this kind of specific spare part supports faster parts selection, cleaner rebuild planning and a more exact return to the intended XV-02/TRF specification.  Warning! Not suitable for children under 14 years.