RC tuning parts
Higher, faster, further with Tamiya tuning parts. Tune your RC vehicles just the way you want them. If you would like to find out more, you can read more here.
RC tuning parts
0.4 Module Pinion Gear Set, RC accessory, 28/29T
300053262€18.99
This 0.4 module steel pinion gear set brings precise gearing changes to compatible RC chassis, with 28T and 29T pinions that allow a finer adjustment of the transmission ratio than broader tooth-count steps. The steel construction and compact geared form suit drivetrain setups where efficient transfer of motor output matters on the track. The set is supplied as 6 parts: 2 pinion gears, 3 set screws and 1 hex key for installation. The pinions are intended for use with separately available 0.4 module spur gears, and the data names specific pairings for several chassis families. FF-03 and FF-03 PRO use it with 54227, TB-03, TB-04 and TB-04 PRO use it with 54055, TA05 Ver.II uses it with 53857, and F104 or F104W use it with 54166 plus 53104 or 53900. F104PRO II uses it with 54166. Compatible chassis named in the data include F104PRO II, F104 Ver.II PRO, F104W, F104, FF-03, FF-03 PRO, TA05 Ver.II, TB-04, TB-04 PRO, TB-03, TRF103, TRF102 and TRF101. In workshop use, the two tooth-count options support quick ratio changes between runs, while the included hex key helps with fitting and adjustment at the bench or trackside. Warning! Not suitable for children under 14 years.
RC tuning parts
04 Spur Gear 93T/104T, RC gear set, 0.4 module
300053900€9.79
The 04 Spur Gear 93T/104T set is a drivetrain tuning part for RC chassis that use 0.4 module gearing. With 93T and 104T spur gears in one pack, it supports finer ratio selection than the standard 0.6 module gear and opens up smaller adjustment steps when acceleration and running efficiency need closer control. Each gear uses a fine tooth profile that changes how the spur and pinion mesh, making this set useful when a standard ratio jump is too broad for the setup. Molybdenum in the gear material is specified to reduce friction resistance at the contact point, which supports smoother power transfer through the drivetrain. The set is intended for F103 and C Car chassis and is used together with 0.4 pinion gear #53101. That compatibility matters when preparing a chassis for different track layouts, motor characteristics or rolling conditions where a small gearing change can alter response. On a bench setup, the 2 tooth counts make back-to-back comparison straightforward because the gearing can be changed with a direct spur swap. On the track, that means a setup can be tuned toward sharper pull out of slower sections or toward a more efficient running balance across a full session.
RC tuning parts
1:10 Touring Car Short Springs II, RC spring set
300054797€19.99
The 1:10 Touring Car Short Springs II set brings finer suspension tuning to touring car setups by adding 3 short spring rates that sit alongside the existing range. Each pack contains 6 black coil springs arranged as 3 pairs, giving a direct way to alter chassis response for changing track conditions and different driving inputs. The set includes 2 Super Hard springs with white marks, 2 Medium-Hard springs with gold marks and 2 Medium-Soft springs without a color mark. That spread broadens the choices beyond the Hard, Medium and Soft options in Item 42168, making it easier to narrow in on a more exact setup. The color coding helps keep spring pairs sorted during rebuilds, test sessions and repeated suspension changes. As short springs, they are intended for touring car short damper layouts rather than standard-length units. Compatibility covers touring car short dampers in Items 50519, 50746, 53155, 53280, 53571, 53901, 54000, 54753, 42102, 42273, 42287, 42291 and 47342. On a practice day or between race heats, swapping one pair for another gives a clear mechanical route to adjusting handling balance through the suspension rather than changing the whole chassis setup. Warning! Not suitable for children under 14 years.
RC tuning parts
33T Steel Idler Gear, chassis spare part
300022087€9.49
This 33T steel idler gear is a dedicated spare part for selected RC chassis and brings a precise transmission component into repair and maintenance work. Supplied as 1 piece, it is intended for use with the BB-01, TD2, TD4 and XV-01 chassis, where the stated 33-tooth specification matches the required internal gear position. The part is used in place of MA27, identified in the source data as the green gear in the reference image. That direct replacement note matters during servicing, because it points to the exact gear position rather than leaving fitment to guesswork. The steel construction suits a mechanical role inside the drivetrain, while the compact gear form with central hub and slot reflects its function as a transmission component rather than an external accessory. For chassis owners keeping a running model in service, a clearly specified spare like this helps restore the intended internal setup with the named tooth count and platform compatibility. It fits naturally into workshop tasks such as replacing a worn transmission gear during a rebuild, refreshing a used chassis, or keeping a matching spare on hand for BB-01, TD2, TD4 or XV-01 maintenance. The single-piece format keeps the scope clear when one exact idler gear is needed. Warning! Not suitable for children under 14 years.
RC tuning parts
3x23mm Turnbuckle Shaft, RC spare part, blue
300054248€8.79
These 3x23 mm turnbuckle shafts are built for RC chassis tuning where precise linkage adjustment matters. The central turnbuckle section changes shaft length without removing the adjusters, which helps keep setup work direct when steering or suspension geometry needs a measured correction. The blue anodized finish gives the aluminum parts a clean technical look that stands out clearly in a parts tray or on the workbench. The set contains 2 threaded rods and is intended for a wide range of compatible chassis: M-06, M-06 PRO, TA06 MS, TA06, TA06 PRO, TA05, TB-Evo.7, TB-05 PRO, TT-02 TYPE-SR, TT-02 TYPE-S, XV-02PRO, XV-01, XV-01 PRO and XV-01T. Aluminum construction keeps the parts light while providing the rigid threaded form needed for repeatable adjustment. The 3x23 mm size makes this pair a specific fitment choice rather than a generic linkage part, which is useful when maintaining an existing build or preparing a chassis for a setup change. On a bench build, these shafts suit routine replacement, geometry correction or tuning updates between running sessions. The visible center section supports tool access for small length changes, making them practical spares for regular chassis maintenance.
RC tuning parts
4x18mm Titanium Turnbuckle Shafts, RC chassis part
300022086€11.99
These 4x18mm titanium turnbuckle shafts are a dedicated chassis option part for the TA08R family and related Tamiya platforms. The titanium construction pairs low weight with a crisp machined finish, while the threaded design allows the shafts to serve as key linkage hardware in compatible RC chassis assemblies. The set contains 2 shafts and is specified for use with the TA08 PRO, TA08R and TB Evo.8 chassis. Each shaft uses a double-threaded layout with a narrow centre section, a format commonly used where steering or suspension links need compact, accurately made connection points. As an option part, this pack suits routine maintenance, targeted replacement of worn hardware, or a planned chassis refresh using the exact stated size of 4x18mm. For a complete kit application, 4 shafts are required. In workshop use, the clearly defined compatibility helps when matching parts to an existing TA08 PRO, TA08R or TB Evo.8 build. The 2-piece pack also supports staged servicing, whether replacing individual linkage points or combining multiple packs to equip a full chassis with the required shaft count. Warning! Not suitable for children under 14 years.
RC tuning parts
5mm Alum. Ball Nut, RC spare part, blue, 10 pcs
300053640€14.29
This spare parts set supplies 10 aluminium ball nuts in a 5 mm format for RC model maintenance, with a blue anodized finish that gives compatible assemblies a clean, uniform look. Each piece combines a rounded ball head with a hexagonal base, a shape that supports attachment to matching sockets and linked mechanical parts where smooth, accurate movement matters. The set is intended for replacing worn ball connector nuts before play in the linkage becomes imprecise. Fresh hardware helps compatible steering and suspension connections seat correctly and move with less unwanted slack, which supports consistent running performance during regular use. The included quantity of 10 pieces suits full maintenance sessions, partial rebuilds or keeping matching replacements ready in a workshop parts box. Scope of delivery: 10 ball nuts. These aluminium ball nuts fit naturally into routine service work on RC models that use this connector style, whether a single linkage needs attention or several mounting points are being refreshed together. They cannot be used on DT-02 chassis XB models. Warning! Not suitable for children under 14 years.
RC tuning parts
5mm L.Friction Adjuster, RC spare part, 8 pieces
300053601€6.79
The 5 mm L.Friction Adjuster set brings a focused upgrade to linkage movement on compatible RC models. Made from a low-friction material, these ball connectors help linkage rods move smoothly at the connection point, which suits steering tie-rods and camber links that rely on clean, consistent articulation. Each pack contains 8 adjusters and is intended for many Tamiya vehicles that use a 3 mm turnbuckle. The 5 mm connector size makes this set a practical choice when worn rod ends need replacement across several mounting points in the same setup. The parts are supplied as adjustment pieces for model maintenance and tuning, with the connector shape built around ball-joint style linkage use. Compared with the standard material, this low-friction version lasts longer before replacement is needed. The set fits naturally into workshop tasks such as refreshing steering linkages, rebuilding camber link connections, or keeping spare rod-end parts ready between running sessions. DT-02 chassis compatibility is stated, while XB model use is not possible. Warning! Not suitable for children under 14 years.
RC tuning parts
5mm Suspension Balls, RC spare parts, low friction
300054747€9.29
These 5mm suspension balls bring a focused drivetrain and chassis tuning detail to compatible RC vehicles by reducing friction where the suspension pivots. Made from POM resin and supplied as a set of 8, they suit Tamiya vehicles that utilize 5mm suspension balls and give a straightforward way to refresh worn hardware or standardize a setup across multiple corners of the chassis. The design was originally used on the TRF419X chassis, which places these parts in proven competition-oriented running gear rather than generic workshop stock. At each mounting point, the low-friction surface helps the suspension move with less resistance as arms and linkages cycle through travel. That smoother motion can help the suspension react more cleanly to steering input, surface changes and load transfer, especially when a setup depends on free, consistent movement at small contact points. In workshop use, this set fits naturally into routine rebuilds, race preparation and parts replacement on compatible models. The 5mm size keeps selection simple for chassis built around that specification, while the pack of 8 provides enough pieces for a complete refresh of key suspension connection points on many layouts.
RC tuning parts
630 Ball Bearings, chassis tuning parts, set of 8
300054925€15.49
This set of 630 ball bearings adds a direct mechanical upgrade to compatible chassis by replacing plain rotating contact points in the reduction gears with metal bearings designed for smoother running. With 8 bearings in the pack, the set suits targeted maintenance work or the first stage of a driveline tune-up on G6-01TR and GF-01TR models. The main effect comes from lower friction at moving points inside the reduction gear assemblies. That reduction in drag helps the drivetrain transfer motion more efficiently and can lessen wear on surrounding rotating parts over time. The bearings have a compact round format with a polished metal finish, matching the small-scale hardware used in RC chassis assemblies. Each reduction gear requires 2 of these 630 bearings, so quantity planning is straightforward when preparing a larger rebuild. A full GF-01 setup needs 16 bearings in total, while a full G6-01 setup needs 24. In workshop use, the set fits neatly into routine servicing, parts replacement, or a gradual chassis upgrade path. It can be used to refresh a model that has seen regular running or to prepare compatible reduction gears before the next driving session.
RC tuning parts
Alu Wheel Hub Clamp Type 9mm, RC car hub set
300054610€16.79
This clamp type wheel hub set adds a precise 9 mm setup option for compatible RC cars that use hex hubs to secure the wheel on the axle. Each aluminum hub clamps directly onto the wheel axle, a fastening method that increases holding strength while supporting smoother wheel rotation during running and tuning work. The set contains 2 wheel hubs, a 1.5 mm hex wrench, cap screws and 2 x 10 mm shafts for attachment. The machined aluminum parts keep weight low while giving the hub area a crisp, technical fit. At 9 mm thickness, this version expands the range beyond 4 mm, 5 mm and 6 mm hub options, which makes it useful when adjusting track width and wheel position on suitable chassis. The instruction data also notes that fit depends on wheel width and offset, and wheels may contact the bodyshell on some combinations. Compatibility covers TT-01 and TT-02 chassis with longer wheel axles and wide rear tread, plus GF-01 and WR-02G chassis cars. In a workshop setup, the clamp design, included hardware and exact 9 mm thickness make this set a practical choice for replacing wide type wheel hubs or refining the stance of an existing RC car build.
RC tuning parts
Alu. Motor Guard GF-01/WR-02, RC motor cover
300054817€38.99
The Alu. Motor Guard GF-01/WR-02 adds a compact aluminum shield around the motor area on compatible Tamiya chassis, combining physical protection with airflow-focused shaping. Slotted openings across the guard help dissipate heat while the cover reduces direct exposure to dust and debris during running. The set contains 1 aluminum motor guard, 2 cap screws in 3x28 mm size and a hex wrench for attachment. Its cylindrical clamp-style form wraps closely around the motor, while the front flange uses multiple mounting holes to secure the part in position. The aluminum construction gives this accessory a precise machined look that suits detailed RC builds and upgrade-focused maintenance. Compatibility is stated for GF-01, G6-01 and WR-02 chassis cars, making it a targeted fit for those platforms rather than a universal add-on. On dirt sections, mixed surfaces or general outdoor running, the guard adds a useful barrier where loose debris can gather around the motor can. It also suits workshop refreshes and chassis upgrades where a cleaner motor area and a more finished mechanical layout are part of the goal.
RC tuning parts
Alum. Adjustable SepSusMt (A), RC chassis mount
300054884€25.99
Alum. Adjustable SepSusMt (A) brings bushing-based suspension tuning to compatible RC chassis cars with a compact aluminum mount set that replaces the standard suspension mount. The two separate mounts, A-a and A-b, work with offset bushings to alter suspension shaft position, opening detailed setup changes that can be felt in how the chassis is balanced for different track conditions. The set contains 1 Aluminum Adjustable Suspension Mount (A-a), 1 Aluminum Adjustable Suspension Mount (A-b) and 1 bushing sprue. The bushing sprue provides 7 pairs of bushing types, and each type uses a different hole position for the suspension shafts. Rotating and pairing those bushings creates 25 potential shaft offset positions, which allows fine adjustment of toe angle, tread, roll center and skid angle. The mount itself allows settings between XA and C, while the final toe angle depends on the separate suspension mounts and bushings used. Shims can be used to adjust clearance where needed. The blue anodized finish gives the aluminum parts the familiar Tamiya look on the chassis. Compatibility is stated for TRF419, TA07 and TB-05 chassis cars, making this set a focused upgrade for racers refining suspension geometry with measured, repeatable changes.
RC tuning parts
Alum. Ball Connector blue 5mm, RC spare part
300053642€13.79
These 5 mm aluminum ball connectors are a focused upgrade and replacement part for the DT-02 chassis, combining low weight, durable metal construction and a blue anodized finish in a compact hardware set. Each connector uses a threaded shaft, a hexagonal base section and a spherical head, creating a secure mounting point that still allows the linked component to articulate smoothly during running. The set contains 10 ball heads, making it useful for servicing several connection points in one session or keeping matching spares ready for later maintenance. The anodized blue finish gives the hardware a crisp technical look while also making the parts easy to distinguish during a rebuild. Replacing worn connectors in time helps maintain clean linkage action where play or wear can reduce consistency. These parts are not available for XB model use. On a workbench, the connectors suit routine chassis upkeep, targeted repairs and detail-focused tuning on a compatible DT-02 build. Once fitted, the smooth ball shape supports free movement at the joint, which matters wherever linked parts need to pivot through repeated steering or suspension travel. Warning! Not suitable for children under 14 years.
RC tuning parts
Alum. HT Servo Saver Cap, RC spare part, aluminum
300054863€5.59
The Alum. HT Servo Saver Cap is a compact RC spare part that combines a machined aluminum build with a precise fit for hi-torque servo savers. Used in place of the Q4 part, it creates a durable contact point at the saver and brings a crisp blue anodized finish to the steering area, where small hardware details remain visible during maintenance and setup. Its disc-shaped form with a countersunk center is made to seat the fixing screw neatly while keeping the cap aligned in the assembly. The aluminum construction adds a lightweight metal component to a high-load area, and the laser-engraved TAMIYA name gives the surface a clean workshop look without changing the part's function. Supplied as 1 cap, it is suited to replacing a worn original part or refreshing a compatible saver with the same specified shape and role. On an RC chassis, this cap fits naturally into routine steering service, rebuild work or detail-focused tuning. It is especially useful when a hi-torque servo saver is already apart for inspection and the Q4 position needs a fresh, more durable replacement component.
RC tuning parts
Alum. Turnbuckle Shaft 3x18mm, RC spare part
300054247€8.79
The Alum. Turnbuckle Shaft 3x18mm in blue is a compact RC spare part for chassis setups that call for precise linkage adjustment. Made from lightweight aluminum, each shaft combines threaded ends with a central section that supports clean, controlled length changes while the part remains installed, which helps keep setup work focused and efficient at the bench. The 3 x 18 mm format suits a wide range of compatible Tamiya chassis, including M-08 CONCEPT, M-06, M-06 PRO, MF-01X, TA08 PRO, TA07 MSX, TA07 MS, TA07 PRO, TB-Evo.6 MS, TB-Evo.6, TRF420X, TRF420, TRF419XR, TRF419X, TRF419 and TT-01D TYPE-E. A blue anodized finish gives the aluminum surface a crisp technical look and makes the parts easy to spot during maintenance. The stopper uses a slot that is tightened with a cap screw to lock the shaft securely. This layout also supports subtle position adjustment when a carbon shaft is used, while avoiding shaft damage and reducing the need to install or remove bearings during service. With 2 threaded rods in the set, the pair fits neatly into regular repair, replacement and tuning work on compatible RC chassis. Setup sessions, trackside checks and workshop maintenance all benefit from hardware that can be adjusted directly and returned to the car with minimal interruption. Warning! Not suitable for children under 14 years.
RC tuning parts
Alum. Turnbuckle Shaft 3x42mm, chassis part
300054250€9.39
These 3 x 42 mm aluminum turnbuckle shafts add a clean, mechanical adjustment point to compatible RC chassis, with a blue anodized finish that stands out clearly during bench work and maintenance. The threaded ends and central wrench section support direct length changes on the installed linkage, so setup corrections can be made without removing the adjusters first. The pair is intended for chassis including TA07 PRO, TA06, TA06 PRO, TA06 MS, TB-04, TB-04 PRO, FF-04 EVO, TRF419, TRF419X, TB Evo.6, TB Evo.6 MS, XV-01 PRO and XV-01T. Aluminum construction keeps the parts light while providing a precise metal interface for linkage duties. The turnbuckle format is especially useful where camber, toe or related linkage geometry needs measured adjustment through small rotational changes at the shaft body rather than full disassembly. With 2 threaded rods in the set, the parts suit paired replacement on one linkage point or a focused tuning update on an existing chassis build. The metallic blue surface also makes the shafts easy to identify among other hardware during servicing, rebuilds and trackside setup checks. Warning! Not suitable for children under 14 years.
RC tuning parts
Aluminum Adjustable Servo Horn for RC Steering
300054893€43.99
This aluminum adjustable servo horn adds fine steering setup control to compatible RC chassis by allowing the distance between the servo horn center and ball connector to be set in 1 mm increments from 15 to 22 mm. That mechanical adjustment changes the linkage geometry directly, making it possible to tune steering throw with a part that sits at the heart of the steering system. The horn also allows steering range adjustment, which helps match the setup to different chassis layouts in the compatible CC-01, GF-01, G6-01, M-05, M-06, M-07 Concept, M-08 Concept, TA07 PRO, TB-05 PRO, TT-02 and TT-02B families. Its aluminum construction brings a precise, machined feel to a component that handles repeated steering inputs. A built-in servo saver function adds impact management at the horn itself, so shocks from crashes are not transferred straight into the servo mechanism. On a touring, rally or off-road chassis, this part supports careful steering tuning through measurable linkage changes rather than guesswork. It suits rebuilds, maintenance work and setup changes where steering response and protection both matter in the same installation.
RC tuning parts
Aluminum Servo Horn, RC steering arm for TAMIYA/FUTABA
300042248€15.99
This aluminum servo horn brings a direct steering link to compatible RC chassis and replaces servo saver action with a firmer connection at the servo output. The result is a sharper steering response that suits precise setup work on track-focused models, while the blue alumite finish and machined cut surfaces give the part a clean technical look. The arm uses a raised pillow ball mounting point set 1.5 mm higher to reduce linkage interference and maintain steering angle through the linkage movement. A clamp-style serration section adds extra holding force at the spline, and tightening the 2 x 5 mm cap screw secures the horn more firmly than a screw-only layout. Scope of delivery: 1x servo arm. The part is specified for TAMIYA/FUTABA fitment and is listed for TA07 MSX, TA07 MS, TA06 MS, TB-Evo.7, TB-Evo.6 MS, TB-Evo.6, TRF420X, TRF420, TRF419XR, TRF419X and TRF419. On a competition chassis, small steering changes are easy to feel, and this direct horn is built for that kind of exact linkage setup. It suits rebuilds, tuning changes and replacement work where secure spline clamping and clean pillow ball positioning matter to the steering system. Warning! Not suitable for children under 14 years.
RC tuning parts
Aluminum Turnbuckle Shaft Set, RC Chassis Spare
300054249€8.79
This spare part set brings adjustable linkage tuning to a wide range of RC chassis with 2 aluminum turnbuckle shafts in a blue anodized finish. Each shaft uses a central hex section that allows length changes while the adjusters stay in place, making setup work on steering or suspension linkages more direct and controlled. The shafts measure 3 x 42 mm and are intended to replace the standard A12 parts in compatible kits. Supported chassis listed in the data include TT-02 Type-S, TA07 PRO, TA06, TA06 PRO, TA06 MS, TB-04, TB-04 PRO, FF-04 EVO, TRF419, TRF419X, TB Evo.7, TB Evo.6, TB Evo.6 MS, MF-01X and RM-01. For TC-01 chassis, use with adjusters such as 54869 is specified. The aluminum construction adds a metal component where repeated setup changes call for a precise threaded part with a clear wrenching point at the center. On a bench build, these shafts suit geometry changes that need repeated fine adjustment between runs. In maintenance or upgrade work, the 2-piece set provides direct replacement parts for worn or standard kit linkages on the named chassis families. Warning! Not suitable for children under 14 years.
RC tuning parts
Ball Bearing Set 1150, RC car accessory, 16 pcs
300054579€30.99
The Ball Bearing Set 1150 brings a focused drivetrain upgrade to compatible R/C car chassis by replacing plastic bushings with 16 metal bearings sized at 11 x 5 x 4 mm. Each bearing supports smoother rotation at key moving points, helping the transmission run with less drag during acceleration and steady laps. This set is intended for a straightforward tuning change that targets friction where axles and drivetrain parts turn under load. In compatible entry level platforms, the swap can help reduce power loss through the driveline while also supporting the longevity of axle joints. The pack provides enough bearings for several listed chassis layouts: DT-03 and DT-02 require 14 bearings, while WR-02, WR-02G and WT-01 require 16. That fitment detail makes the set useful both for a complete replacement on some chassis and for a near-complete conversion on others. On the bench, the compact 1150 format suits builders refining a buggy or wheelie platform with a practical mechanical upgrade rather than a cosmetic change. It fits naturally into maintenance work, rebuilds and fresh kit preparation where smoother rolling parts and more efficient drivetrain movement matter most.
RC tuning parts
BB-01 Alum. Servo Stays, chassis accessory
300022070€23.99
These BB-01 Alum. Servo Stays bring a metal mounting upgrade to the BB-01 chassis with 2 silver-anodized aluminium parts shaped for the servo stay position. The machined L-form, stepped inner corner and mixed drilled and threaded holes give each stay a defined structural role inside the chassis layout. The set contains 2 stays, allowing the left and right mounting points to match in material and finish. The silver anodized surface gives the aluminium a clean technical look, while the threaded holes support direct fastening at the intended fixing points. The larger plain holes and the vertical leg geometry indicate a part designed to hold position accurately once installed. As a chassis accessory rather than a general hardware piece, this set is focused on the BB-01 platform named in the data. That makes the pair a useful choice when refreshing a used chassis, replacing the standard servo stays, or adding a more detailed metal element during a new BB-01 build. On the bench, the 2 matching parts bring a neat, uniform appearance to the servo mounting area and keep the upgrade closely tied to the specified chassis system.
RC tuning parts
BB-01 Aluminium Damper Stays Rear Accessory
300022089€26.99
The BB-01 Aluminium Damper Stays Rear accessory adds a metal mounting set to the rear section of a BB-01 chassis build. Its layout is intended for installation under the roll cage roof, where the rear aluminum damper mount bar works with the included adapters and stiffener post to create the specified attachment point. The silver-anodized finish gives the visible parts a clean technical look that matches detailed off-road model assemblies. Included in the set are 1 rear aluminum damper mount bar, 1 stiffener post, 2 damper mount adapters and 2 3x30 mm hex head screws. The two adapters use a double-hole form, while the long central bar and the post create a compact hardware group for the rear damper mounting area. This makes the set useful for BB-01 owners looking for the exact parts named for this chassis rather than a generic hardware mix. In a workshop setup, the parts suit maintenance, replacement or a focused chassis update where the rear mounting section needs the specified metal components. The compact contents also make the set easy to keep with other BB-01 spares for later fitting or rebuild work. Warning! Not suitable for children under 14 years.
RC tuning parts
BB-01 Aluminium Steering Arms L/R, chassis upgrade
300022090€28.99
The BB-01 Aluminium Steering Arms L/R bring a focused steering upgrade to the BB-01 chassis with silver-anodized aluminum parts shaped for the left and right sides. Replacing the standard S2 and S3 parts, these arms add rigidity at a key point in the steering linkage, helping inputs travel through the assembly with a more linear response. Each set contains 1 left arm and 1 right arm, so the steering assembly can be updated as a matched pair rather than mixing materials across the same mechanism. The arm shape uses a larger recessed mounting end and a smaller drilled connection point, with reinforced contours around the structure to support accurate pivoting movement inside the front steering layout. This makes the set especially relevant for builders refining steering feel on a BB-01 based machine rather than changing unrelated chassis areas. The parts are intended for use in place of the original S2 and S3 components on compatible builds. Use with Item 22091 is recommended. Ball bearings are required separately. On the bench, this upgrade suits rebuilds, maintenance work, or a fresh BB-01 assembly where the steering system is being specified with metal linkage parts from the start. Warning! Not suitable for children under 14 years.
RC tuning parts
BB-01 Aluminum Damper Stays Front RC Hop-Up
300022088€44.99
These BB-01 Aluminum Damper Stays Front parts add a focused chassis upgrade to the front damper mounting area. The set uses 2 silver-anodized aluminum stays in place of the standard A27 parts, bringing a metal component to a section that handles the damper attachment points on the BB-01 layout. Alongside the 2 stays, the set provides 2 P3 O-rings, 2 P4 O-rings, 4 countersunk 3x12 mm hex head screws, 2 standard 3x12 mm hex head screws, 2 5 mm ball posts and 4 aluminum spacers measuring 3.1 x 4.4 x 1.0 mm. The countersunk holes in the stays work with the included flush screws for a neat fit. The paired O-rings and spacers support the specified mounting arrangement, while the ball posts add the required connection points for the front setup. This accessory suits builders refining a BB-01 buggy with dedicated chassis parts rather than universal hardware. During assembly or maintenance, the silver finish stands out clearly against surrounding components, making the upgraded front section easy to identify on the bench and on the completed model. Warning! Not suitable for children under 14 years.
RC tuning parts
BB-01 Aluminum Front Uprights, chassis parts
300022069€53.49
These silver-anodized aluminum front uprights are made for the BB-01 chassis and supply a matched 2-piece set for the front suspension area. The identical right and left shape keeps both sides visually consistent and streamlines parts selection when the chassis is being serviced or updated. Each upright features a large central opening for the hub area plus smaller mounting points for the surrounding front-end hardware. That layout supports accurate positioning within the chassis assembly and gives the front corner a clean, precisely machined metal component in place of the standard part. The silver anodized finish adds a crisp technical look that stands out clearly during a build or maintenance session. As a dedicated BB-01 chassis part, this set suits replacement after wear, a rebuild of the front end, or a selective aluminum conversion focused on the upright area. The 2 included pieces cover both front sides, making the pair a straightforward choice when matching geometry and finish across the chassis matters.
RC tuning parts
BB-01 Aluminum Steering Bridge, chassis part
300022091€14.79
The BB-01 Aluminum Steering Bridge is a dedicated chassis part for the BB-01 platform, built to replace the standard S1 part with a silver-anodized aluminum component. Its rigid construction strengthens the steering linkage area, supporting a more direct steering feel and a more even response as the front end changes direction. The part comes as 1 piece and is shaped for the BB-01 chassis layout, so it serves as a focused hardware upgrade rather than a general universal fitting. The silver-anodized finish gives the machined aluminum surface a clean technical look while matching the functional role of a precision steering component. The bridge uses the existing mounting position in place of the S1 part, concentrating the upgrade on the connection point that guides steering movement. Use with Item 22090 is recommended. Ball bearings are sold separately. In a workshop build or a running chassis refresh, this steering bridge suits BB-01 owners who want to refine the front steering assembly with a specific metal replacement part. It also fits well into a step-by-step tuning plan where individual steering components are upgraded one area at a time. Warning! Not suitable for children under 14 years.
RC tuning parts
BB-01 Slipper Clutch Set, chassis spare part
300022071€57.49
The BB-01 Slipper Clutch Set adds an adjustable drivetrain element to the BB-01 chassis, centering on a gear-integrated shaft with 20T layout and a spring-loaded clutch assembly. By changing spring tension, the clutch alters slip timing and acceleration traction, which can help the chassis deliver steadier power when grip changes across the surface. The set contains the slipper clutch for BB-01 Chassis and is supplied with the core assembly parts: 1 gear-integrated shaft, 1 slipper screw, Plate A, Plate B, 2 slipper pads, 1 1050 ball bearing, 2 spring seats, 1 spring and 1 2.6 mm lock nut. The friction-based clutch action lets the drivetrain absorb part of the initial load under acceleration instead of locking the drive instantly, giving more scope to tune how the BB-01 responds as power comes in. The included spare part 86T gear extends service support for the same chassis platform. This set suits rebuilds, routine maintenance and setup changes on BB-01 running cars. It can be fitted when refreshing worn drivetrain parts or when a different clutch response is needed for changing track grip, repeated acceleration runs or general chassis tuning.
RC tuning parts
C.V.A.II Damper Collar, RC spare part set
300050950€7.69
The C.V.A.II Damper Collar set is a dedicated RC spare part for suspension maintenance on selected Tamiya platforms. Supplied as 1 sprue with 22 parts, it concentrates on the damper area and gives compatible chassis a defined source for replacement and setup work. Fitment is stated for DT-02 chassis, DT-03 chassis and DT-03T chassis, with additional use on vehicles equipped with 54567. For DN-01 chassis, the data also names an important restriction: 54028 cannot be used together. That combination note matters during parts planning because it keeps the suspension configuration aligned with the listed specification rather than trial fitting unrelated pieces. The set is not available for XB models, which separates it clearly from those versions. On the bench, this spare part set suits routine damper service, rebuilds after wear, or preparation of a compatible chassis before the next run. The 22-part sprue format keeps the included pieces together in one pack, making it easier to sort the required parts for maintenance on the supported DT and DN platforms. Warning! Not suitable for children under 14 years.
RC tuning parts
Carbon Short Damper Stay Set, RC chassis upgrade
300022076€48.99
This Carbon Short Damper Stay Set brings front and rear carbon fiber damper stays into one focused chassis upgrade for XV-02 and XV-02RS cars. The woven carbon fiber plates use multiple mounting holes and slotted positions to open up suspension setup changes, so shock geometry can be adjusted with more precision on paved running surfaces. The set contains 2 damper stays, 4 piston rods measuring 30.5 mm, 8 blue 5 x 6.55 mm ball connector nuts, and 8 round head socket screws in 3 x 10 mm size. The front and rear plates have distinct shapes for their mounting positions, with rounded outer edges, central slots and lower slotted openings that support different attachment points. That layout helps tune how the dampers sit on the chassis and how the suspension reacts through direction changes and corner entry. The supplied piston rods are specifically oriented for on-road performance rather than a general mixed-surface setup. On an XV-02 chassis, this set is used with Items 42102, 54465 and 54871; it also fits XV-02RS chassis cars. It suits builders refining a rally platform for asphalt sessions, club practice or repeatable setup testing where small geometry changes can be felt from one run to the next.
RC tuning parts
CC-01 Alum. Oil Damper Set, RC chassis upgrade
300054541€66.99
The CC-01 Alum. Oil Damper Set is an RC chassis upgrade made for the Tamiya CC-01 platform, using aluminum dampers to bring more composed suspension movement to cross-country running. On loose gravel, rutted tracks and uneven ground, the oil-filled design helps the chassis absorb repeated bumps with a steadier response than a basic friction setup. The set provides the parts needed to assemble 4 dampers, covering both front and rear positions for a balanced suspension layout. Each damper uses a silver anodized cylinder with a dark titanium anodized cap, giving the hardware a clean mechanical look that matches detailed off-road builds. V parts are included, along with small attachment parts for mounting to the chassis. The assembly sheet for the damper set notes standard oil as #400 and indicates separate front and rear spring use from the base kit. This upgrade suits builders refining a CC-01 for trail driving, rocky paths or mixed-surface sessions where repeated compression and rebound shape how the chassis settles after bumps. It also fits restoration or tuning work on an existing CC-01, where metal dampers can replace worn stock units with a full 4-piece suspension set. Warning! Not suitable for children under 14 years.
RC tuning parts
CC-01 Barrel Spring Set, chassis tuning springs
300054666€20.29
The CC-01 Barrel Spring Set adds a focused suspension tuning option to compatible CC-01 chassis cars, using 6 coil springs in 3 stiffness grades to change how the chassis reacts over rough ground. Its barrel shape creates progressive damping, which means resistance increases the further each spring is compressed, giving the suspension a more measured response when the surface starts to break up. The set contains 2 soft springs, 2 medium springs and 2 hard springs, making it possible to fit matched pairs and compare different setups with the same chassis. The springs are shown with colour bands that identify hardness at a glance, helping setup changes stay organised when several rates are on the bench. The shorter and longer spring forms in the set broaden the tuning range within the CC-01 platform and keep the adjustment centred on suspension behaviour rather than cosmetic changes. On loose tracks, gravel paths or uneven off-road sections, the progressive spring action supports a smoother ride and helps the chassis manage body roll with more control. For maintenance, replacement or planned tuning sessions, this spring set gives CC-01 owners a direct way to refine handling through a core suspension component.
RC tuning parts
CC-02 Damper Spring Set, RC chassis suspension parts
300054992€18.29
Built for CC-02 chassis cars, this damper set upgrades the suspension with 4 aluminum cylinders shaped for lower friction and a slimmer profile than the kit-standard cylinders. That narrower cylinder form changes the visual balance around the axles and gives the chassis a more scale-focused look while the dampers work through bumps, ruts and side-to-side weight transfer. Each damper uses cylinder caps, O-ring caps and adjustable retainers, with small attachment parts included to complete the installation. The top and bottom mounting points use ball connectors, replacing the kit's upper screw and collar arrangement. That mounting change supports smoother roll motion, especially when the chassis articulates over uneven ground or settles into off-camber sections. The set is intended to kit out a full 4-damper layout on the CC-02 platform rather than changing only one corner of the suspension. Compatibility stays flexible for tuning work, because the dampers can be paired with kit-standard springs or with the dedicated springs sold separately as Item 54992. This makes the set a useful choice for builders refining suspension response, scale appearance and chassis movement on trail-style RC vehicle builds.
RC tuning parts
CC-02 Full Ball Bearing Set, chassis tuning set
300054910€35.99
The CC-02 Full Ball Bearing Set is a focused chassis tuning upgrade for compatible CC-02 models, built around 22 metal bearings in 4 specified sizes. Installed in the rotating points of the chassis, the bearings support smoother movement and more efficient transfer of drive power than plain bushings, which helps the model run with less drag during use. The size mix of 2x 850, 16x 1150, 2x 1260 and 2x 1510 is matched to the CC-02 platform, so the set covers a full conversion with the required quantities already grouped in one pack. Ball bearings are often one of the first mechanical upgrades added to an RC chassis because they reduce friction where shafts and driven parts turn under load. That lower friction can also help reduce wear in those contact areas over time, especially on a model that sees regular running and routine servicing. During a rebuild, maintenance session or fresh chassis assembly, this set gives a direct route to replacing bushings with bearings across the specified CC-02 layout. The compact metal parts suit hobby benches where precise fit and orderly parts selection matter, and the pre-matched count keeps the upgrade process straightforward for the intended chassis family. Warning! Not suitable for children under 14 years.
RC tuning parts
CC-02 Motor Mt. Bridge Spacer, chassis accessory
300054971€27.29
The CC-02 Motor Mt. Bridge Spacer adds a focused chassis upgrade to CC-02 builds by reinforcing the motor mounting area with an aluminum part placed between the gearbox and the motor cap screws. That extra support helps keep the motor fixed in position, which contributes to a more efficient drive when the gears are set correctly and turning smoothly. The spacer also braces the gearbox against warping, giving the motor mount area firmer support under load. Its gun metal anodized finish matches the technical character of RC chassis hardware, while the curved bridge shape and elongated slots support accurate placement during fitting. The instruction diagram shows the spacer used with 3 x 14 mm cap screws and 3 mm washers while the motor position is adjusted to create proper gear backlash. This setup allows clearance for the gears to run lightly instead of binding at the mesh point. On a workbench build or a maintenance session, this part suits drivers refining drivetrain feel on a CC-02 chassis car. It can be fitted when replacing motor mount hardware, correcting gear mesh, or adding stiffness to the gearbox area for more consistent running across repeated sessions.
RC tuning parts
Clamp Alu Wheel Hub, accessory set, 5 mm blue
300053823€36.29
Clamp Alu Wheel Hub 4 5 mm blue brings a more secure wheel mounting setup to compatible Tamiya chassis through a split aluminium hub tightened by cap screws. The machined blue hubs sit neatly at the axle area and are designed to hold firmly during running, while the clamp construction also keeps 2 x 10 mm stainless steel shafts from slipping out when the hub is removed. This accessory set is intended for a broad range of chassis platforms, including TT-02, TT-02 Type-S, TT-02D, TT-01D Type-E, TT-01 Type-E, TT-01 Type-ES, TA07 PRO, TA06, TA06 PRO, TA06 MS, TA05 Ver.II, TB-04, TB-04 PRO, FF-04 EVO, FF-03, FF-03 PRO, TRF419, TRF419X, TB Evo.7, TB Evo.6, TB Evo.6 MS, M-07 Concept, XV-01T and XV-01 PRO. Use with item 53646 or 53647 is specified where required. The scope of delivery lists 1 Wheel Driver Set with 15 pieces, and the product image shows 4 blue clamp hubs, metal screws, pins and an L-shaped hex key. On a workshop bench, the cap screw fixing allows each hub to be tightened with a direct mechanical grip rather than a simple push fit. During maintenance, wheel removal and refitting stay controlled because the shaft hardware remains retained in the assembly, which helps keep small drivetrain parts organised between runs. Warning! Not suitable for children under 14 years.
RC tuning parts
Clamp Type Alum Hubs NarTrd (4), wheel hubs
300042352€20.99
Clamp Type Alum Hubs NarTrd (4) brings a focused chassis tuning option to touring car models with 4 narrow tread clamp type wheel hubs in aluminum. Mounted at the wheel area, these hubs allow a narrower tread setup that can be used at the front for sharper steering response, at the rear for improved grip, or across the whole car to tune overall balance on the track. Each hub uses a clamp type design and comes with 5 cap screws in 1.6 x 4 mm size for installation. The aluminum construction is finished in Tamiya blue anodizing, giving the parts a crisp technical look that stands out during maintenance and setup work. Compatibility covers TA06, TA06 PRO, TA06 MS, TA07 PRO, TA07 MS, TB-04, TB-04 PRO, TB-05 PRO, TB Evo.6, TB Evo.6 MS, TB Evo.7, TRF419, TRF419X, TRF419XR, TRF420 and TT-02 Type-S chassis. For use with 24 mm width medium-narrow wheels, and items 53646 and 54573 may be required. This set fits naturally into bench tuning before practice laps, race-day setup changes, or a rebuild focused on steering feel and rear traction. The 4-hub format supports a full car conversion, while the clamp layout keeps the adjustment centered on a small but influential chassis component.
RC tuning parts
CR-01 Reinforced Drive Shaft Diff Lock Set
300054108€46.49
Built for the CR-01 chassis, this reinforced drive shaft and diff lock set changes the axle drivetrain into a more direct, mechanically linked setup. The reinforced long and short drive shafts work with diff lock case A and diff lock case B to lock securely in place, supporting efficient power transfer when the axle is under load. The differential lock parts install in place of the bevel gears, as shown in the assembly layout, so the axle no longer relies on standard differential action. That change keeps both sides of the axle turning together, a setup often chosen for technical crawling lines where steady drive at both wheels matters. The set also uses 4 mm E-rings together with 3 x 6 mm screws and 2 x 5 mm cap screws in the assembly. Scope of delivery: 1 reinforced differential lock set with 14 pieces. As a chassis-specific tuning set, these parts suit CR-01 builds that need drivetrain components matched to the original axle housing layout. The black mechanical parts format also makes the upgrade easy to identify during maintenance, parts replacement or a fresh rebuild of the axle section. Warning! Not suitable for children under 14 years.
RC tuning parts
CR-01 Reinforced Wheel Axle, chassis spare pair
300054048€11.29
The CR-01 Reinforced Wheel Axle is a chassis spare pair made for the CR-01 platform and supplied as 2 matching replacement parts. Each axle uses stronger material than the standard version, giving this small drivetrain component a more durable basis where wheel-end hardware and repeated impacts concentrate force. The dark metal finish and machined form underline its role as a functional running part rather than a cosmetic add-on. Each piece combines a slotted lower section, a smooth central shaft with a cross-hole and a threaded tip, so the axle can take its place within the existing wheel assembly layout. The upgraded cup area brings improved wear resistance, targeting a contact point that sees repeated movement during running. That makes this pair a practical choice when a CR-01 build needs fresh axle hardware after demanding use on steep sections, uneven ground or hard descents. In workshop use, the pair suits routine maintenance, worn-part replacement or a durability-focused refresh of an existing chassis setup. For RC owners keeping a CR-01 ready for regular trail sessions, these 2 axles add a direct fit spare option centered on strength and wear performance. Warning! Not suitable for children under 14 years.
RC tuning parts
Damper Set Alum. M-Chassis (4), RC damper set
300054000€99.99
This aluminum damper set brings a chassis-specific suspension upgrade to M-Chassis builds with 4 oil dampers developed around a shorter format. The damper cylinders and damper rods are 2 mm shorter than touring car aluminum dampers, which lowers ride height and opens up more exact stroke adjustment on compact chassis layouts. The set is supplied as a 118-piece assembly package with threaded cylinders, adjustment nuts, springs, pistons, O-rings and mounting hardware. A hard black coating on the damper surfaces reduces friction, while the blue damper caps and white springs give the assembled suspension a crisp mechanical contrast. The internal setup can be tailored through piston choice, with 2-hole and 3-hole pistons specified for different chassis positions in the included build information. Standard damper oil is #400, and damper oil is available separately. On the bench, the set supports detailed front and rear suspension work for M-03, M-04, M-05 and M-06 chassis. It can also be used with TT-01 TYPE-E and TT-01D TYPE-E chassis together with 54059 and 54060, and with MF-01X chassis when the stated 5 x 9 mm cushion balls are added. The result is a more precisely tunable damper package for drivers refining ride height, spring tension and damping response. Warning! Not suitable for children under 14 years.
RC tuning parts
DB-01/TRF501X Reinforc.Belt, drive belt
300054140€11.99
This reinforced drive belt is a dedicated transmission spare part for the DB01, TRF501X WE and TRF511 chassis, combining a 369 size and 3.7 mm width with a toothed inner profile that transfers motion through the drivetrain. In a running model, that layout supports steady power delivery where the belt tracks around pulleys inside the chassis. The belt is supplied as 1 reinforced drive belt and is described as dust repelling, a detail aimed at keeping the drive path cleaner during operation. Its flexible construction is paired with low drive resistance, so the drivetrain can run with less drag while maintaining the belt's engagement on the teeth. The reinforced belt core is stated as about 1.5 times stronger than previous drive belts, and the reinforcement is also described as helping prevent tooth slip under load. That combination makes it a focused replacement part for restoring transmission performance on the named chassis. Used in maintenance, rebuilds or race-day spares, this belt suits model setups where the original transmission part needs replacement after wear. Kept in a pit box or workshop drawer, it gives the stated chassis platforms a matching spare for routine drivetrain service. Warning! Not suitable for children under 14 years.
RC tuning parts
DB01/TRF511 Gear Differential Unit 37T RC Part
300054329€43.99
The DB01/TRF511 Gear Differential Unit 37T adds a sealed oil-filled differential layout to compatible RC buggy drivetrains, replacing the kit-standard ball differential used on DB-01 and 511/502 chassis. That change opens another tuning route at the center of the transmission, where oil viscosity directly influences how quickly the differential moves under load on loose or changing off-road surfaces. Inside the assembly, a 37T pulley works with 12T and 20T bevel gears, while the sealed case uses a gasket, O-rings, shafts, shims and screws to hold the oil around the internal gear set. The instruction data specifies filling the case until the bevel gears are covered, making the working principle clear and easy to service. Higher viscosity oil slows differential movement, so the same unit can be adjusted for different grip levels and handling balance. Compared with a standard ball differential, this gear differential requires less frequent maintenance cycles. The included cross shaft from Item 54311 is supplied as standard, and the differential joint cups can also be sourced later as spare parts. On a prepared buggy, this unit suits drivers who tune for specific track conditions rather than leaving the stock setup unchanged. It also fits workshop maintenance sessions where a worn drivetrain is being refreshed with a sealed differential format that can be reopened, refilled and adjusted as running conditions change. Warning! Not suitable for children under 14 years.
RC tuning parts
DF-02/TT-01 Front One-way Unit, RC drivetrain set
300053671€84.99
The DF-02/TT-01 Front One-way Unit changes the front drivetrain layout by replacing the front differential gear with a one-way mechanism. Under power, the front end keeps traction engaged; when throttle is off, the difference in rotation between front and rear wheels is canceled, supporting smoother, stall-free cornering on technical sections and tighter turns. The set contains 19 parts and is built around the one-way ring gear, left and right front one-way housings, one-way joints, bearing spacers and 1060 flanged ball bearings. During assembly, the housing and ring gear holes are aligned and secured with 2 x 8 mm cap screws using the included 1.5 mm hex wrench. The instructions also note a 6 mm washer adjustment when a universal shaft shows excess play at the one-way joint, giving a clear mechanical route to fine-tuning fit. Fitment details matter with this upgrade. TT-02 TYPE-S and TT-02 TYPE-SR chassis use it together with 53590, TT-02B requires the 6 mm O-ring MB16 in the connection cup, and TT-02RR uses the kit wheel axle and driveshaft together with 53590. For DF-02 and TT-01 based builds, this unit suits tuning sessions focused on front-end response and drivetrain behavior rather than cosmetic changes alone. Warning! Not suitable for children under 14 years.
RC tuning parts
DF-03 Damper Spring Set, chassis tuning set
300053927€26.99
The DF-03 Damper Spring Set adds a focused suspension tuning option for compatible RC buggy chassis by putting 12 metal coil springs with 3 distinct hardness levels into one pack. Soft black, medium gold and hard silver springs give a clear starting point for adjusting how the dampers react to bumps, grip changes and direction shifts on different surfaces. The 3x4 configuration supplies a full set arrangement, so matching spring rates can be fitted across the vehicle instead of mixing unrelated parts. On loose dirt, a softer rate can help the suspension move more freely over uneven ground, while firmer springs suit higher-grip sections and route layouts that call for a tighter response. The color coding speeds up setup checks between runs because each hardness level is easy to identify at a glance. This set is specified for DF-03, TT-02B, DB02, DB01, DN-01 and TRF201 chassis, and TT-02B use is stated together with 53926. At the bench, the springs give a direct way to test setup changes before the next battery pack goes in. On the track, that means suspension tuning can follow the road surface and course shape more closely, whether the goal is a calmer reaction over rough sections or a firmer feel through faster lines. Warning! Not suitable for children under 14 years.
RC tuning parts
DT-03 Carbon Damper Stay Front RC Chassis Part
300054562€19.49
The DT-03 Carbon Damper Stay Front is a chassis upgrade part for DT-03 cars that brings a stiffer front damper mounting point to the suspension layout. Its carbon plate construction and symmetrical multi-hole pattern give the front end a clean, technical setup for damper installation, with the curved upper edge and twin lower tabs shaped to match the chassis mounting area. This set is supplied as ITEM 54562 and is intended to replace the standard C5 part on the DT-03 platform. The included hardware consists of 2 ball connector nuts, 2 3x8 mm screws and 2 3x0.7 mm spacers, which match the mounting points shown for the stay itself. The drilled positions allow adjustment of damper attachment points, which helps builders alter front suspension geometry through the mounting location rather than through unrelated chassis changes. The part is documented for use in place of C5 and for compatibility with the DT-03 CVA Damper Set. On a buggy prepared for loose dirt, compacted track sections or repeated jump landings, the front stay gives the suspension area a more focused base for setup changes. It suits workshop tuning sessions where front damper position, linkage fit and chassis response are adjusted step by step on a DT-03 build.
RC tuning parts
DT-03 Carbon Damper Stay Rear, chassis upgrade
300054563€22.59
The DT-03 Carbon Damper Stay Rear brings a focused chassis upgrade to DT-03 models by combining carbon fiber construction with a rear suspension mounting layout designed for tuning. The flat carbon plate gives the dampers a rigid mounting point, helping the suspension work with a more direct, controlled feel during running sessions. A series of mounting holes across the stay creates more setup scope than a fixed-position part. Damper angle and mounting position can be adjusted to explore different handling responses, making the part useful for track tuning as well as routine chassis refinement. The set also contains the small attachment parts needed for installation, so the carbon stay can be fitted as a complete rear mounting component rather than as a bare plate alone. The instruction data identifies it as a replacement for the standard stay position on DT-03 chassis models. On a prepared buggy, this kind of upgrade comes into its own when surface grip, corner entry and rear stability need closer adjustment through damper position changes. It also suits workshop builds that focus on replacing standard chassis parts with lighter, more rigid option components matched to the DT-03 platform. Warning! Not suitable for children under 14 years.
RC tuning parts
DT-03 Full Turnbuckle Set, RC chassis upgrade
300054572€22.49
The DT-03 Full Turnbuckle Set adds adjustable linkage hardware to DT-03 chassis cars, replacing fixed upper arms and tie-rods with 6 stainless steel turnbuckle shafts. Threaded adjustment makes it possible to fine-tune link length for a more exact chassis set-up while the buggy sits on the bench between runs. The set includes 2 shafts in 3x32 mm, 2 in 3x38 mm and 2 in 3x65 mm, covering the different positions used around the chassis. Each shaft uses an adjustment section that can be turned with the included wrench, so changes can be made without removing every linkage point first. Stainless steel construction gives the shafts a clean, precise finish suited to repeated set-up work, and the supplied attachment parts support installation on compatible DT-03 models. This upgrade suits drivers who want to refine alignment after a rebuild, correct steering link length, or make measured suspension changes for different running conditions. On a maintenance table, at a club session, or between outdoor buggy runs, the set gives the DT-03 platform a more tunable linkage layout with parts sized for direct compatibility.
RC tuning parts
DT-03 Gear Shaft, RC spare part, 5x45mm pair
300054560€3.49
The DT-03 Gear Shaft lightweight 5x45mm set is a focused drivetrain upgrade for DT-03 chassis cars, replacing the shafts used with the spur gear and counter gear. Its pipe construction cuts weight at a rotating point in the transmission, which supports a lighter, more efficient drive layout during buggy running. Each shaft measures 5x45 mm and the set contains 2 matching pieces for the specified replacement point. The hollow metal form does more than change mass: it also helps dissipate heat, which is especially useful around the drivetrain area where moving parts work continuously. Because the change is concentrated in the gear shaft position, the upgrade targets mechanical efficiency without altering the stated DT-03 fitment. This set suits maintenance, repair, or a planned drivetrain refresh on compatible DT-03 chassis cars. Kept as workshop spares or fitted during a rebuild, the 2 shafts offer a straightforward way to swap out the standard kit parts with a lighter alternative matched to the same application.
RC tuning parts
DT-03/02 19T Steel Pinion Gear, M0.8 Accessory
300054629€5.89
This M0.8 module 19T steel pinion gear is a focused drivetrain upgrade for compatible chassis cars, pairing a compact motor-side gear with a tougher material choice for repeated running sessions. The steel construction is stated as more durable than the kit-standard aluminum pinion gear, helping reduce wear at a part of the transmission that sees constant tooth contact. The gear is supplied as 1 piece and comes with a grub screw for attachment, so the pinion can be fixed directly to the motor shaft in the intended position. The 19-tooth specification keeps the gearing at the stated tooth count, which matters when maintaining an existing transmission setup rather than changing to a different ratio. The M0.8 module matches the stated gear format, giving a clear fit reference alongside the chassis compatibility. Compatible DT-03 and DT-02 chassis cars can use this part as a replacement when the original pinion shows wear or when a steel version is preferred for longer service life. In workshop use, this kind of part suits routine drivetrain upkeep between running sessions, especially when a worn motor pinion starts to affect mesh quality. It also fits neatly into a spares box for chassis-specific maintenance, ready for the next rebuild or transmission refresh.
RC tuning parts
DT-03/02 Ball Diff.-Set, RC drivetrain upgrade
300053863€51.99
The DT-03/02 Ball Diff.-Set is an RC drivetrain upgrade for compatible DT-03 and DT-02 chassis, built to add a ball differential with limited slip effect. That setup improves traction and mobility while keeping the car more settled in fast cornering, so power delivery feels cleaner when the rear end is working across changing grip. Inside the assembly, the gear width is reduced from 20 mm to 15 mm, a change that cuts friction loss in the drivetrain. The set contains 29 parts and includes 2 17 mm thrust washers, 10 steel balls, 1 1150 thrust bearing, 1 diff gear, 1 stepped bolt, pressure plate A, pressure plate B, a pressure plate cap, and long and short gearbox joints. The included grease shown for the ball differential supports the contact surfaces during setup and running. This differential layout also helps protect the gears from damage and wear by managing load through the drivetrain more effectively. Compatibility covers selected DT-03 and DT-02 chassis models such as NEO FIGHTER, RACING FIGHTER, DESERT GATOR, SAND VIPER, NEO FALCON and HOLIDAY BUGGY. For operation, universal joint shafts 300053791 or shaft set 309805551 with 300050823 are required separately. This makes the set a focused choice for tuning an existing buggy with a more adjustable differential action and a drivetrain setup aimed at traction and cornering stability. Warning! Not suitable for children under 14 years.
RC tuning parts
DT-03/02 M0,8 Module 17T Steel Pinion Gear
300054628€5.89
The DT-03/02 M0,8 Module 17T Steel Pinion is a drivetrain upgrade part for compatible chassis cars, built to place a steel gear at the point where motor output transfers into the transmission. Its M0,8 module and 17-tooth layout define the meshing geometry, while the compact pinion format keeps the part focused on clean, direct power delivery inside the gear train. Compared with the kit-standard aluminum pinion gear named in the data, this steel version is intended for greater durability and increased gear life during repeated running. The straight-cut teeth and central bore create the working interface, and the side fixing point uses the included grub screw to fasten the gear onto the shaft. The set contains 1 pinion gear and 1 grub screw, keeping the replacement focused on the essential mounting hardware. The black metal finish and engraved top-face marks give the part a technical, workshop-ready look that matches its mechanical role. In a maintenance setup, this gear suits rebuilds after drivetrain wear or ratio changes that call for a 17T pinion in the specified module. It also fits neatly into a spares box for DT chassis servicing, where a correctly matched steel pinion helps keep compatible RC cars running with the intended gear mesh.
RC tuning parts
DT02&TT01 3x22 LF Sus. Shaft, RC spare parts
300054395€8.19
The DT02&TT01 3x22 LF Sus. Shaft set is a focused RC hardware upgrade for compatible Tamiya chassis, replacing 3 x 22 mm screw pins with shaft parts secured by E-rings. That change gives suspension link points a firm mechanical hold while keeping the assembly compact and precise around moving components. Each shaft has a low-friction coating that supports smoother suspension action as the linked parts cycle through movement. The set includes 4 silver metal shafts with machined grooves and 10 matching E-rings for installation. This configuration suits maintenance work on worn hardware, a planned rebuild, or a fresh chassis assembly where the specified shaft format is required. The grooved ends provide the retention points for the E-rings, so the fastening method is built into the part itself rather than relying on threaded screw-pin installation. Compatibility covers DT-03, DT-03T, DT-02, TT-02RR, TT-02D, TT-02 and WR-02 chassis. In workshop use, the parts support clean replacement of existing suspension hardware and help keep moving assemblies operating with a consistent mechanical feel across repeated runs. Warning! Not suitable for children under 14 years.
RC tuning parts
F-104 HT Saver Alu. Horn, servo horn, blue aluminum
300054159€25.49
The F-104 HT Saver Alu. Horn is a machined aluminum servo horn for the High Torque Servo Saver, created to replace the Q5 section and give the steering system a firmer, more direct feel. Its anodized blue finish makes the part easy to identify during a build or maintenance session, while the metal construction targets stiffness in the steering area rather than changing unrelated chassis parts. This servo horn is specified for the High Torque Servo Saver 300050473 in white and 300051000 in black. The stated fit list also names F104 and the F103 15th Anniversary Chassis Kit Item 84056, plus DT-03 and DT-03T chassis. Further listed applications include TB Evo.7, M-08 CONCEPT, F104VerⅡ, TRF101, DT2 and DT4, showing that the part serves as a focused steering upgrade across multiple supported platforms. The change in material from the standard saver section to machined aluminum is aimed at reducing flex in this specific linkage point. In workshop use, this part suits builders refining steering response on compatible chassis or replacing the original saver horn with a stiffer alternative. It fits naturally into maintenance, rebuild and tuning routines where exact servo saver behavior matters on the bench and on the track. Warning! Not suitable for children under 14 years.
RC tuning parts
F104 Spur Gear Adapter, RC chassis accessory
300054215€3.99
The F104 Spur Gear Adapter is a drivetrain accessory for selected Formula chassis that expands gearing options by allowing touring car spur gears to mount on F103 and F104 platforms. That added compatibility supports finer ratio selection, so a setup can be matched more closely to motor choice and driving area when tuning a model for different running conditions. The adapter is supplied as 1 spur gear adapter and works with a defined group of chassis that includes F104PRO II, F104Ver.II PRO, F104W, F104, F103GT, TRF103, TRF102 and TRF101. Compatible spur gears listed for this part are 50978, 51056, 51215, 53857, 54055 and 54227. The installation layout places the adapter on the shaft before the spur gear, where it acts as the mounting interface for the gear assembly. Depending on the transmission used, the spacer may also allow an increase in the number of differential balls. In workshop use, this part suits rebuilds, ratio changes and chassis-specific drivetrain updates where a broader spur gear selection is needed. It also fits maintenance sessions that replace worn transmission parts while keeping an existing Formula chassis in active running trim. Warning! Not suitable for children under 14 years.
RC tuning parts
F104/F103 Front Upright, RC spare part, reinforced
300054154€8.29
The F104/F103 Front Upright reinforced set is an RC spare part for Formula chassis that replaces the kit-supplied K-6 component with a reinforced design. Supplied as 2 front steering knuckles, the set is intended for front-end service, rebuild work or a targeted upgrade when running a high-output motor or a 0.4 module spur gear. Each upright uses a black molded structure with a ribbed arm section and a mounted metal shaft, creating a compact assembly for the front steering area. The pair format supports matched installation on the left and right side, while the threaded shaft ends and included fastening hardware suit precise chassis work at the bench. Compatibility covers F104PRO II, F104Ver.II PRO, F104W, F104, TRF103 and TRF101 chassis, making this set a useful stock part for several Formula platforms in one pit box. During maintenance between race sessions, worn front-end parts can be swapped as a pair to keep steering hardware consistent across the axle. On a fresh build or chassis refresh, the reinforced construction suits setups that place extra demand on the front assembly, especially when stronger drive output or the stated gear configuration is in use. Warning! Not suitable for children under 14 years.
RC tuning parts
FC 5mm Alum. Ball Nut, RC accessory set
300053599€16.79
These FC 5 mm aluminum ball nuts bring a precise hardware upgrade to compatible RC model chassis, combining a low-friction coating with a lighter aluminum build for smoother moving connections. Supplied as a set of 10, they suit linkage points that rely on clean articulation and consistent mechanical contact during running and setup. Each part uses a rounded ball head with a hexagonal fastening base, a shape that supports controlled installation and a defined connection point for linked components. The metallic finish and machined form match the technical character of model chassis hardware, while the 5 mm specification keeps the fit tied to the stated application. The set is intended for DT-02 chassis use. Cannot be used on DT-02 chassis XB models. This pack fits naturally into maintenance, repair, or tuning work where worn hardware is being replaced or a chassis is being assembled with selected upgrade parts. In workshop use, 10 matching ball nuts provide consistent hardware across several connection points, helping keep steering or suspension movement even across the build. Warning! Not suitable for children under 14 years.
RC tuning parts
Gear Differential Shim Set, model accessory, 0.2/0.3 mm
300054589€7.49
The Gear Differential Shim Set 0,2/0,3mm (4) brings precise spacing control to oil-filled gear differential units used in compatible RC models. With 2 shim thicknesses, 0.2 mm and 0.3 mm, the set allows fine adjustment of the bevel gears so the differential can be set up with closer attention to mesh and internal fit. Each shim measures 5 x 10 mm, making the set suitable for the specified differential format rather than a broad, undefined range of uses. The pack contains 4 shims in 0.2 mm and 4 shims in 0.3 mm, which gives scope for incremental changes during maintenance, rebuilds or tuning work. This is a focused workshop accessory for differential setup, where small measurement changes can matter across the gear train. The set is intended for Tamiya oil-filled gear differential units employed in 4WD touring cars and 4WD off-road buggies. It fits naturally into bench work such as refreshing a differential, correcting gear spacing or preparing a drivetrain for the next running session, with both shim sizes ready in one pack.
RC tuning parts
Lo-Mount Aluminum Retainers, RC damper spring set
300022080€28.49
These Lo-Mount Aluminum Retainers for Large-Diameter Springs adjust spring position lower on compatible RC car dampers, giving the suspension a cleaner working range and a more direct response in handling. The set includes 4 retainers and 4 aluminum spacers sized 5.5 x 0.5 mm, forming a focused tuning upgrade for cars that run large-diameter springs. A thinner section between the damper ends and cylinders allows damper stroke to be used more efficiently, which helps the spring move with less interruption through compression and rebound. Large-diameter springs are often paired with Super Short Big Bore dampers, making this set a useful option when refining suspension geometry around that layout. The slotted retainer shape supports installation around the damper assembly while keeping the update compact and purpose-built. Compatibility depends on the suspension arm shape and damper angle of the chassis in use. On some setups, contact between the dampers and suspension arms can occur, and any interfering area may need to be shaved down. This makes the set best suited to detailed suspension tuning where spring height, stroke use and chassis response are being adjusted with care.
RC tuning parts
M-03/04/05/06 Reinforced Gear Set, chassis spare part
300054277€8.29
The M-03/04/05/06 Reinforced Gear Set black is a drivetrain spare part for selected Tamiya M chassis platforms, built to refresh the gearbox with reinforced transmission components. The black parts set suits repair work, scheduled maintenance and rebuilds where worn internal pieces can affect how cleanly the drivetrain runs. The scope of delivery contains 1 gearbox with 5 parts. Visible component types include spur gears, a splined shaft and circular gearbox pieces that work together inside the transmission housing. As the gears mesh, rotational force is carried through the drivetrain, so the condition of these internal parts matters for smooth mechanical engagement. The reinforced construction is intended as a durable option in the gearbox, as stated in the source data. Compatibility is specified for chassis M-05, M-05 PRO, M-05 Ver.II PRO, M-06 and M-06 PRO. This set fits naturally into workshop tasks such as replacing tired gearbox internals after long running use or preparing a compatible chassis for a fresh rebuild. In a bench setup, the defined platform list helps match the parts to the correct transmission family before installation, keeping service work clear and focused. Warning! Not suitable for children under 14 years.
RC tuning parts
M-05 Low Friction King Pin, chassis hardware
300054237€10.59
The M-05 Low Friction King Pin set brings a focused chassis upgrade to compatible Tamiya platforms by combining stronger metal hardware with a special plated surface that reduces friction loss. In use, that lower-resistance contact supports smoother movement at the relevant suspension or steering mounting point, making this set a practical choice for maintenance, repair, or setup refinement on running models. Each pack contains 4 silver-coloured king pins with a rounded head, a smooth shoulder section and a threaded end. The hex screw head provides a positive drive for tool engagement during fitting, which helps keep attachment controlled when replacing worn hardware. The set is listed for DF-03 chassis, M-06 chassis, M-06 PRO chassis, M-05 ver.II PRO chassis, M-05 chassis, M-05 PRO chassis and MF-01X chassis. The supplied parts are also described as usable with M-05, M-05Ra and TA04 chassis machines. This hardware suits bench servicing, parts replacement and small tuning updates where consistent fastening parts matter across the assembly. Kept in a spares box or fitted during a rebuild, the 4-piece set supports straightforward upkeep of compatible chassis systems. Warning! Not suitable for children under 14 years.
RC tuning parts
M-05 VII Stainless Sus Shaft Set, chassis upgrade
300054613€7.29
The M-05 VII Stainless Sus Shaft Set upgrades the suspension mounting points on M-05 Ver.II PRO chassis cars with 8 stainless steel shafts and matching 2 mm E-rings. Used in place of screw pins, these shafts attach the front and rear arms with a more exact fit, helping the suspension move with greater precision during running and setup work. The set includes 2 newly designed 3x58 mm shafts, 2 shafts in 3x48.5 mm, and 4 shafts in 3x37 mm, covering the different positions shown for the chassis layout. Each shaft has grooves near the ends for E-ring retention, and 16 E-rings are supplied for attachment. The installation guide shows the shafts fitted through the front and rear pivot points, where they are locked in place with the 2 mm E-rings. Long nose pliers are used to attach the retaining rings during assembly. This chassis option suits builders refining an existing M-05 Ver.II PRO setup or replacing the original pin arrangement with stainless steel hardware. On the bench, the different shaft lengths correspond to specific front and rear mounting locations, making the set a focused upgrade for suspension arm attachment rather than a general hardware assortment.
RC tuning parts
M-05 VII Suspension Arm Set, chassis parts
300054606€10.19
The M-05 VII Suspension Arm Set updates the front and rear suspension layout with 1-piece arms developed for the M-05 Ver.II platform. Compared with the standard 2-piece M-Chassis arrangement, the single-piece design increases rigidity at the arm section, which supports a more direct handling feel during setup and running. This set is used on Item 58593 M-05 Ver.II PRO Chassis Kit and also works as a service replacement when original arms are worn or damaged. The front installation uses chassis kit-included parts in place of C3, C4 and C8, while the rear installation replaces C11 and C19. Left and right arm orientation matters during fitting, and the instruction material shows the required mounting positions for front and rear assemblies. For rebound stroke adjustment on M-05 and M-05 PRO chassis, Item 54605 chassis parts are required so the droop screw can be used on the suspension arm itself. Compatibility covers M-05 Ver.II PRO, M-05 and M-06 chassis. M-05 Version 1 and M-06 platforms require parts modification as described on the 54606 instruction sheet. The set suits maintenance, repair and chassis updates where a Version 2 suspension specification is needed.
RC tuning parts
M-05/M-Chassis Freewheel Axle Set (2), RC axle set
300054183€12.29
The M-05/M-Chassis Freewheel Axle Set (2) brings a precise axle upgrade to compatible Tamiya chassis, using machined wheel axles to support a cleaner wheel fit and reduced play at the mounting point. In a workshop setup or during routine chassis maintenance, that added accuracy helps keep the wheel assembly feeling more exact. This set is built around 2 wheel axles and 10 shims, each shim measuring 0.2 mm for fine adjustment work. The shim stack allows small setup changes instead of broad spacing steps, which is useful when dialling in axle fit on M-Chassis platforms. Compatibility covers FF-04 EVO, FF-03, FF-03 PRO, M-08 CONCEPT, M-07 CONCEPT, M-06, M-06 PRO, M-05 ver.II PRO, M-05 and M-05 PRO chassis. The same axle set can also be used for the rear wheels of the M-05 chassis, the rear wheels of the M-03 and the front wheels of the M-04. On a bench, the parts suit rebuilds, replacement work and tuning-focused maintenance where wheel play needs closer control. The compact set fits naturally into a spares box for M-Chassis running gear, ready for targeted axle changes on compatible front-wheel-drive and M platform builds. Warning! Not suitable for children under 14 years.
RC tuning parts
M-07 Concept Alu. Heat Sink RC chassis accessory
300054759€22.79
The M-07 Concept Alu. Heat Sink adds a focused cooling upgrade to the motor area of the M-07 Concept chassis. Its aluminum body uses raised fins to dissipate heat during extended running, helping the motor maintain steadier performance when temperatures build over the course of a long race. The curved shape is designed to mount neatly around the motor position on the chassis, and the blue anodized finish gives the part a crisp technical appearance that stands out during maintenance or setup. A 3 x 8 mm screw is included for attachment, matching the part to its intended mounting point without the need to source separate hardware. The fin structure increases surface area at the motor mount, which supports heat transfer away from the motor can while the chassis is in use. After running, the heat sink may become hot and should be handled with care. This accessory suits M-07 Concept builds that spend longer periods on track, where repeated acceleration and sustained pace can raise motor temperature. It also fits well into maintenance routines that focus on chassis-specific tuning parts rather than broad universal add-ons. Warning! Not suitable for children under 14 years.
RC tuning parts
M-07 Concept Carbon Bumper Support for RC Chassis
300054791€14.49
The M-07 Concept Carbon Bumper Support is a focused chassis upgrade for M-07 Concept cars, replacing the standard B2 part with a carbon fiber version that combines low weight with higher rigidity. Mounted at the front section of the chassis, it is designed to keep the urethane bumper securely in place during running and handling. The support uses a curved plate shape with 2 large mounting holes and a wide semicircular cutout, matching the front layout shown for the M-Chassis platform. The set contains 1 carbon fiber bumper support and the small attachment parts needed for fitting. In the installation diagram, the part is fixed with 3 x 8 mm hexagon countersunk screws and 3 mm countersunk washers in place of B2. The carbon fiber construction gives this component a crisp, woven finish while concentrating stiffness in a part that braces the bumper area. On an M-07 Concept build, this part suits drivers refining the front end with selected option components rather than changing the whole chassis layout. It works as a direct replacement in the intended position, making it a clear upgrade choice for maintenance, tuning, or a fresh rebuild of an existing M-Chassis car.
RC tuning parts
M-07 Concept Carbon D Stay F, RC chassis part
300054761€15.99
The M-07 Concept Carbon D Stay F is a front chassis upgrade that swaps the standard damper stay for a 3 mm carbon fiber part with lower weight and higher rigidity. Mounted at the front suspension area of the M-07 Concept chassis, it changes how the dampers are supported and gives the setup a more direct, more defined feel during running sessions. Its 4 attachment holes expand the tuning range beyond the 2-hole kit-standard shock tower, so damper position can be adjusted with finer steps. That added hole count gives more scope to alter front suspension geometry and handling balance around different track layouts. The set contains 1 front damper stay and attachment screws for installation. The instruction data also identifies this part as a replacement for B11 on the chassis. This upgrade suits M-07 Concept builds that are being tuned around front-end response rather than broad parts changes across the whole car. On indoor circuits, club tracks or home practice layouts, the carbon fiber stay adds a focused adjustment point that can be matched to damper setup and driving conditions. Warning! Not suitable for children under 14 years.
RC tuning parts
M-07 Concept Carbon Damper Stay Rear RC Part
300054762€17.59
The M-07 Concept Carbon Damper Stay Rear brings a sharper suspension mounting setup to the M-07 Concept chassis with a 3 mm carbon fiber plate that combines lower weight with greater rigidity than the kit standard part. Mounted at the rear, it gives the damper area a more precise base for setup changes while keeping the upgrade focused on a key handling point. Its layout expands tuning range with 4 attachment holes, doubling the 2-hole arrangement of the standard shock tower. That wider choice of mounting positions supports more exact damper angle changes when dialing the chassis for different track conditions. The set also includes attachment screws for installation. Instruction data shows use with M-07 L and M-07 M configurations, and the carbon stay is installed in place of part B12. The manual also notes part direction during fitting and specifies 3 x 10 mm screws, 3 x 1 mm spacers and 5 mm ball connector nuts in the assembly layout. On a prepared M-07 Concept build, this rear stay suits tuning sessions where suspension geometry changes are tested one step at a time. It also fits maintenance work that replaces the standard molded part with a carbon fiber alternative at the rear shock mounting area. Warning! Not suitable for children under 14 years.
RC tuning parts
M-07 Concept Rein. C Pts, chassis parts set
300054810€12.19
The M-07 Concept Rein. C Pts set brings a stiffer carbon-fiber reinforced nylon option to the M-07 Concept chassis, giving tuning work a more focused mechanical change than a like-for-like replacement. With 2 C parts sprues in the pack, this set targets the areas where molded chassis components influence flex and load transfer during running. The reinforced material changes the flex characteristics compared with the standard kit parts, which is especially relevant on high-grip carpet and asphalt surfaces where chassis response becomes more immediate. The molded parts show bearing seats, hinge-pin style ends and multiple mounting holes, indicating their role in suspension and steering-related assemblies. 4 small metal washers or spacers are also supplied for assembly where spacing needs to be set correctly. As a chassis-specific option part, the set is made for the M-07 Concept platform and suits maintenance, repair and setup refinement with the correct matching geometry. On an indoor carpet track, the added rigidity can support a sharper, more settled feel through linked corners and direction changes. On asphalt, the same material change gives builders another clear setup route when comparing standard and reinforced chassis parts during tuning sessions.
RC tuning parts
M-07 Concept Rein. D Pts, chassis parts
300054811€12.19
The M-07 Concept Rein. D Pts set upgrades the suspension area of the M-07 Concept chassis with carbon-fiber reinforced nylon parts shaped for a stiffer response than the standard kit components. Supplied as 2 D parts sprues, the set is aimed at running conditions where grip levels place more load into the chassis and suspension. The reinforced material changes the flex characteristic of the suspension arms, helping the chassis react more directly on high-grip carpet and asphalt surfaces. That makes this set a focused tuning choice for drivers refining handling balance rather than changing the basic layout of the car. The arm shape, mounting points and platform-specific fit are made for the M-07 Concept chassis, so the upgrade stays within the intended geometry of the platform. The black molded parts shown in the set provide the core suspension components for this specific replacement and tuning role. On carpet tracks and grippy asphalt layouts, suspension loads build quickly through corners, transitions and repeated direction changes. In that setting, a stiffer arm set can support a more consistent chassis feel lap after lap, whether the goal is maintenance of an existing M-07 Concept or a setup change for higher-traction running.
RC tuning parts
M-07 Concept Stabilizer Set FR, chassis accessory
300054757€33.49
The M-07 Concept Stabilizer Set FR adds a focused suspension tuning option to the M-07 Concept chassis with front and rear stabilizers in 2 stiffness levels each. Soft red and hard blue bars give a clear visual distinction during setup work, while the included adjusters make left and right balance changes easier to manage at the bench or between runs. The set contains 2 front stabilizers and 2 rear stabilizers, covering both ends of the chassis with matching tuning parts. Stabilizer stoppers and small attachment parts are included for installation, so the bar system can be fitted as a dedicated chassis upgrade rather than assembled from separate pieces. By changing stabilizer stiffness, the suspension can be set up with a different level of roll resistance, giving a practical route to refining handling characteristics on the M-07 Concept. This accessory suits drivers who like to tune a chassis for different track conditions and driving styles. It works well as a setup addition for test sessions, club racing preparation, or repeatable comparison runs where front and rear balance changes need to be made with specific hardware rather than guesswork.
RC tuning parts
M-07 Concept Steering Arm Set, RC chassis upgrade
300054763€37.99
The M-07 Concept aluminum steering arm set brings a more exact steering action to the front end by replacing the standard K1 and K2 parts with machined left and right aluminum arms. That change sharpens steering response and gives the chassis a more direct feel through the linkage, while the blue anodized finish adds a crisp technical look to the assembly. The set contains 1 aluminum steering arm left and 1 aluminum steering arm right, plus a screw and adjustment shims shown for installation on the steering mechanism. The leaflet specifies use in place of K1 and K2, with a 3 x 8 mm screw and 3 x 5 x 0.1 mm shims used as spacers during fitting. Those shims help set the arm position on the mounting posts so the steering movement stays free and correctly aligned. Aluminum construction also provides a more secure attachment than the standard FRP parts named in the source data. Installed on an M-07 Concept chassis, this hop-up part suits drivers tuning steering precision for track sessions, setup changes or routine maintenance. Ball bearings are required separately, so the set can be matched with the preferred bearing choice during the upgrade. Warning! Not suitable for children under 14 years.
RC tuning parts
M-07 Concept, suspension mount set, aluminum rear
300054760€34.99
The M-07 Concept aluminum rear suspension mount set brings a precise metal upgrade to the rear suspension area of the chassis. 4 blue anodized aluminum mounts replace the standard D4 parts on both sides, creating a secure attachment point for the suspension arms while adding a clean technical finish to the rear end of the car. Each mount is used with an included suspension ball, and the instruction diagram shows the parts fastening in place with 3 x 16 mm hex flat head screws. That layout matters in use: the suspension ball keeps the joint moving smoothly, including setups where toe is applied to the wheels. The set is focused on one specific chassis area rather than a general hardware assortment, which makes it a targeted option for tuning, maintenance or replacing the original rear mount parts on an M-07 Concept build. On the bench, the 4-piece mount set gives the left and right rear sides matching hardware for a consistent installation. During setup work, the aluminum construction and dedicated fit suit builders who want a defined rear suspension mounting point on the M-07 Concept chassis.
RC tuning parts
M-07C Alu Rear Suspension Mount Set, RC chassis
300054787€34.99
The M-07C aluminum rear suspension mount set adds a focused chassis tuning option to M-07 Concept cars by changing the position of the rear suspension shafts. Each mount uses suspension ball holes offset by 0.5 mm from the standard layout, giving 2 different mounting positions that alter rear suspension arm skid angle at the back of the chassis. The set contains 4 aluminum rear suspension mounts in 2 types, with 2 A parts and 2 B parts, plus the small attachment parts needed for fitting. The mounts replace the standard D4 parts on both sides. Instruction diagrams show 2 example geometry settings, including 1.3° skid angle and 0° skid angle, illustrating how the shaft position changes the rear setup. This adjustment also changes rear roll characteristics, making the set useful when tuning handling for different track conditions. The blue anodized finish gives the machined parts a clear visual distinction during assembly and setup checks. Mounted at the rear of the chassis, these parts suit bench tuning sessions where suspension geometry is adjusted step by step and then checked again after running. For M-07 Concept cars used on changing surfaces, the alternate mount positions create a direct way to refine rear-end response through hardware rather than guesswork.
RC tuning parts
M-08 Alum. Frame Posts, RC chassis accessory
300054966€15.49
The M-08 Alum. Frame Posts set brings a focused chassis upgrade to M-08 Concept cars by replacing the kit-standard B8 components with 4 aluminum posts in a blue anodized finish. Fitted at the section that joins the chassis front and rear, these parts increase overall rigidity and support more responsive handling from the rear-wheel drive layout. Each post is supplied as a matching machined component, giving the conversion a consistent fit across the chassis structure. The change in material from the standard parts to aluminum concentrates on the connection area where stiffness matters, helping the chassis react more directly to steering inputs and load changes. The blue anodized surface also adds the signature Tamiya look to the visible hardware without changing the intended compatibility of the car. This accessory is intended for M-08 Concept chassis cars and suits tuning sessions that focus on setup refinement rather than major redesign. All 4 posts are used on M and L wheelbase cars, while S wheelbase cars require 2 posts, making the set suitable for different wheelbase configurations within the M-08 platform.
RC tuning parts
M-08 Concept Steering Arms, Aluminum Upgrade
300054891€32.99
The M-08 Concept aluminum steering arms bring a focused handling upgrade to the chassis by replacing the standard steering linkage parts with machined metal components. Each set contains 1 right steering arm and 1 left steering arm, both finished in Tamiya blue anodizing, for a clean mechanical look that stands out clearly during a bench build or maintenance session. The key change comes from the material itself. Aluminum steering arms guide steering movement with greater precision, which the product data describes as leading to more direct steering feel. The parts also offer extremely secure attachment, supported by the threaded mounting points built into each arm. Their dedicated left and right forms are shaped for the M-08 Concept layout, so the upgrade targets the steering system rather than changing unrelated areas of the chassis. This set is intended for use on the M-08 Concept chassis and is recommended for use with the separately sold steering bridge, Item 54892. In a workshop setup, the pair suits drivers refining steering accuracy on an existing chassis build, and on the track the firmer linkage can help inputs feel cleaner through quick direction changes and technical sections. Warning! Not suitable for children under 14 years.
RC tuning parts
M-08/M-07/TA-06 Steel Bevel Gears, RC spare set
300054428€19.79
The M-08/M-07/TA-06 Steel Bevel Gears bring a metal drivetrain upgrade to compatible RC chassis where angled gear transfer is under constant load. Designed to replace the kit-standard GV1 and GV2 gears, this 6-piece set supports running in tougher conditions such as rally driving and use with a high-powered motor. The bevel gear format is used where drive force changes direction inside the transmission or differential area, so gear accuracy and material choice matter directly to how the drivetrain handles repeated stress. These steel parts are intended for a wide range of chassis including M-08 CONCEPT, M-07 CONCEPT, TA06 variants, DB01, TD4, TD2, FF-04 EVO, XV-01 variants and selected TRF platforms. For TA05 ver.II chassis the set is used with 54312, for DB01 with 54329, and for TD4 and TD2 with 54471. As a spare and tuning set for 14 years and up, the gear pack suits rebuilds after wear, planned drivetrain updates, or preparation for rougher surfaces and stronger motor setups. The delivery scope contains 6 bevel gears, making the contents clear for workshop stock, maintenance planning, and chassis-specific parts selection. Warning! Not suitable for children under 14 years.
RC tuning parts
M-08C Rein. C Parts, chassis parts set, 2deg
300054982€12.19
The M-08C Rein. C Parts set brings carbon fiber-reinforced nylon to a key chassis area, giving M-08 Concept running gear a tougher replacement for the standard glass-fiber reinforced parts. Front and rear uprights sit at the center of wheel location and suspension movement, so this material change targets a part of the car that sees repeated load during cornering, contact and recovery after a crash. Inside the set are 2 M-08 Concept C Parts sprues, supplying the component group used for upright and hub carrier assembly. The instruction reference shows 2deg hub carriers with dedicated R and L orientation, plus a 2.5 mm hole that is made in the specified location during assembly. That layout matters when rebuilding worn suspension parts or preparing a fresh chassis, because the mirrored left and right pieces need to sit in the correct direction around the axle and mounting points. The visible shapes also show bearing and pivot openings that connect the upright assembly to the rest of the chassis hardware. This parts set suits routine maintenance, crash repair and planned setup work on compatible cars. It fits M-07 Concept and M-08 Concept models, making it a practical stock part to keep alongside a regularly used RWD chassis when upright wear or impact damage calls for a direct replacement.
RC tuning parts
M0.6 25T Pinion Gear, RC accessory, hard coated
300054578€9.99
This M0.6 25T pinion gear brings a lightweight aluminum construction and a hard coated finish to RC drivetrain maintenance, tuning and replacement work. The newly designed gear uses rounded teeth, so the mesh runs with lower friction loss while the tooth surface is set up for stronger resistance to wear during repeated use. The 25T format suits setups that call for this exact gearing step, and the M0.6 specification matches 06 Module spur gears for correct pairing in compatible transmissions. A 3 mm grub screw is supplied with the gear, allowing the pinion to be fixed to the motor shaft with the intended mounting hardware rather than requiring a separate screw. The stamped tooth count on the face also makes workshop identification quicker when several gearing options are kept together for setup changes. On the bench, it fits naturally into rebuilds, ratio changes and routine parts replacement for RC models that use M0.6 gearing. In running setups, the rounded tooth profile supports efficient power flow through the drivetrain, making this gear a focused choice for racers and builders who keep a close eye on transmission response and component wear.
RC tuning parts
M0.6 Alu.Pinion Gear 23T, motor pinion gear
300054363€10.29
The M0.6 Alu.Pinion Gear 23T is a drivetrain tuning part for compatible RC chassis that pairs a 23-tooth layout with an M0.6 gear module for accurate engagement at the motor side. Its aluminum construction keeps the part light, while the hard-coated finish is applied to the gear surfaces that handle repeated contact under load. Rounded teeth are used here to minimize friction loss as the gear turns, which supports smooth and efficient power transfer through the drivetrain. The set includes the pinion itself and a grub screw for fastening to the motor shaft. Compatibility covers a wide range of chassis named in the data, including TD4, TD2, CR-01, FF-04 EVO, FF-03, M-08 CONCEPT, M-07 CONCEPT, TA08 PRO, TA07 series, TA06 series, TB series, TC-01, TT-02 series and XV series. For TA07 MS Chassis and TA07 MSX Chassis, use is specified with 51356, 51423 and 51548. This gear suits setup changes where a specific tooth count is needed to match motor response and drivetrain balance in a supported model. On bench setup or race-day maintenance, the clearly defined 23T specification makes it easy to select the right pinion for planned gearing adjustments. Warning! Not suitable for children under 14 years.
RC tuning parts
M0.6 Hard Coated Alum. Pinion 27T, RC pinion gear
300054981€9.99
The M0.6 Hard Coated Alum. Pinion 27T brings a focused drivetrain upgrade to compatible RC chassis, combining an aluminum gear body with a hard-coated finish and a 27-tooth layout. In a compact transmission setup, that combination supports smooth power transfer while the metallic gear profile adds a precise mechanical fit at the motor mount. Its M0.6 module specification makes it a dedicated choice for chassis built around that gear standard, and the engraved 27T marking gives a clear tooth reference during setup changes or maintenance. The included 3 x 3 mm grub screw secures the gear on the shaft, keeping installation centered on the actual drive component rather than extra hardware. Teeth are shaped to reduce loss in the mesh with the spur gear, which means the contact point is engineered not only for drive efficiency but also for quieter running. The hard-coated aluminum surface is used here as a functional treatment on the gear itself, where repeated contact places the most demand on the part. This hop-up part suits tuning sessions that compare gearing changes across touring and shaft-driven chassis, and it also fits well into routine rebuilds when a fresh pinion is needed for a known setup. TT-02 and TT-02D chassis require separately sold Item 54500.
RC tuning parts
M03/04/05/06 Lightweight Hollow Shaft, chassis part
300054319€3.39
The M03/04/05/06 Lightweight Hollow Shaft is a stainless steel chassis upgrade for M-03, M-04, M-05 and M-06 platforms. It replaces the kit-standard 5 x 40 mm and 5 x 21 mm shafts that hold the spur and counter gears, bringing a lighter setup to a key point in the drivetrain while keeping the original function of those parts. The set contains 2 shafts, with 1 long and 1 short version to match the specified gear positions. Their hollow construction removes 6 g compared with the standard parts, a focused change that suits builders refining weight distribution through selected components rather than broad changes across the whole chassis. The polished stainless steel finish also gives the parts a clean mechanical look when the gearbox area is opened during maintenance or rebuilds. This upgrade suits workshop use, scheduled replacement of worn running parts, or a fresh chassis build based on the listed M-series platforms. In a tuning session, it fits naturally alongside other drivetrain-focused changes where small weight reductions and exact fit matter at component level. Warning! Not suitable for children under 14 years.
RC tuning parts
MF-01X Ball Bearing Set, chassis accessory, 24 pcs
300054643€49.99
The MF-01X Ball Bearing Set brings a focused drivetrain upgrade to MF-01X chassis cars by replacing friction-heavy rotating points with metal bearings matched to the chassis layout. With 24 pieces in the set, the bearing selection covers the full conversion needed for the kit and supports smoother running during on-road or rally-style sessions. The set includes 20 1150 ball bearings, 2 850 ball bearings and 2 850 flanged bearings, giving the MF-01X platform the specific sizes required at different mounting points. Ball bearings help rotating shafts turn with less drag than plain bushings, which can improve running efficiency across the drivetrain. The flanged bearing format also suits positions where a locating edge is required in the assembly. As a chassis-specific accessory, this set is aimed at builders who want a direct fit rather than a mixed hardware assortment. During maintenance, rebuilds or a fresh MF-01X assembly, the bearing set adds a practical mechanical upgrade that works at the points where wheels and drivetrain parts rotate under load. It suits hobby benches focused on tuning, replacement and keeping an MF-01X car running cleanly over repeated use.
RC tuning parts
Motor Heat Sink, aluminum RC motor cooler blue
300053664€18.99
This motor heat sink adds focused cooling support to compatible RC chassis with a finned aluminum design and a blue anodized finish that stands out clearly in the drivetrain area. The 11 cooling fins increase surface area around the motor can, helping heat move away more efficiently during longer running sessions. The part is made for DF-02, TT-01D TYPE-E, TT-01 TYPE-E and XV-02PRO chassis, giving these platforms a dedicated motor cooling accessory rather than a universal workaround. Its curved form fits the role of a wraparound heat sink, and the single included component keeps replacement or upgrade work straightforward. As a tuning part, it suits builds where motor temperature management matters during repeated acceleration, extended laps or warm running conditions. Mounted in a compatible chassis, the heat sink supports a cleaner thermal setup around the motor area while adding a bright blue hardware accent. It works well for refresh projects, spare-parts boxes and performance-minded RC maintenance where a specific chassis fit is needed.
RC tuning parts
Motor Pinion Gear 20T Aluminum for F201 Chassis
300053509€14.29
This 20T motor pinion brings a focused drivetrain upgrade to compatible RC chassis with a lightweight machined aluminum body, 0.6 module tooth form and a hard fluorine coated surface. The Gun Gray finish gives the gear a technical look, while the engraved 20 marking helps identify the ratio quickly during setup and servicing. The surface treatment combines cemented carbide alumite processing with added fluorine, creating a steel-like strength characteristic together with strong lubricity at the gear mesh. That combination supports efficient meshing between gears and helps limit wear where the pinion meets the spur gear. The part is specified for the F201 chassis and is intended for builders refining gearing to match track layout, motor choice or driving conditions. Depending on the setup, an alternate spur gear size may be required. In use, the pinion sits at the center of the drivetrain, where small gearing changes can alter how power is delivered out of corners and along straights. The scope of delivery includes 1 motor pinion and 2 x 3 mm grub screws for installation on the motor shaft, making this a compact but meaningful tuning part for RC maintenance, replacement or ratio adjustment. Warning! Not suitable for children under 14 years.
RC tuning parts
On-Road Tuned Hard Spring Set, RC chassis springs
300053440€24.99
The On-Road Tuned Hard Spring Set adds a firmer suspension option for RC chassis setups that need more stability at higher speed. This set contains 8 extra hard springs and is intended for a broad range of compatible on-road platforms, making it a focused tuning part for setup work rather than a general replacement. The springs are part of a 4-step range from soft, medium and hard through to EX hard, with color coding in red, yellow, blue and white for quick identification during setup changes. That coding helps keep spring choices clear when comparing handling differences across multiple runs. The extra hard rate improves stability at speed compared with OP163, and the set can widen the adjustment range when combined with other springs from the same range. For TA07 MS chassis, use is specified with 53571. For F104 chassis and F104W chassis, use is specified with 53901. Compatibility spans many established platforms, including F104PRO II, FF-04 EVO, FF-03 PRO, TA06 PRO, TB-Evo.7, TB-04 PRO, TB-03 VDS, TT-02RR, TT-02 TYPE-SR and XV-01 PRO. In practical tuning sessions, that broad fitment supports repeatable suspension experiments across several chassis families while keeping spring selection clearly sorted by rate and color. Warning! Not suitable for children under 14 years.
RC tuning parts
Pinion Gear 26/27T 48P, RC gear set, steel
300054382€16.79
This RC gear set brings 2 tuning options to compatible drivetrains with a 26T pinion gear, a 27T pinion gear and 48 pitch tooth spacing. Made from carburized steel, both gears are designed for repeated contact in the drive system, where clean meshing and consistent fit matter during running sessions and workshop changes. The offset screw attachment holes are arranged in 2 positions, a detail that helps the gears fit motor shafts of different lengths instead of limiting installation to one shaft format. Rounded teeth are used to minimise friction loss at the mesh point, supporting smoother transfer of motor output through the drivetrain. The set is intended for cars equipped with a 48 pitch spur gear, so the tooth profile matches the required spur specification. A grub screw is included for installation, making the set ready for direct use as a replacement part or gearing change. On a bench setup, the 26T and 27T combination allows a quick switch between 2 tooth counts when servicing an RC car or adjusting the drive layout for a different setup. It also works well as a spare set to keep alongside other drivetrain parts for routine maintenance on compatible models.
RC tuning parts
Pinion Gear Coated Alu 22T M0.6, RC gear
300054770€9.99
This 22T pinion gear brings a focused drivetrain upgrade to RC maintenance and tuning work. Made from aluminum and finished with a hard coating, it combines reduced rotating weight with a surface built for repeated gear contact. The M0.6 specification matches 0.6 module spur gears, making the gear pitch clear at a glance when selecting replacement or setup parts. Its rounded teeth are designed to cut drivetrain friction loss while improving resistance to wear. That tooth profile matters at the mesh point, where the pinion transfers motor output into the transmission with every rotation. The 22-tooth count also gives a defined gearing option for builders adjusting acceleration and running characteristics through pinion changes rather than larger drivetrain modifications. A central bore and set screw are provided for mounting the gear onto a shaft. On the bench, this gear fits naturally into rebuilds, ratio changes and routine servicing of compatible RC drivetrains. It works as a direct spare when a worn pinion needs replacement, and it also supports more deliberate setup changes when a transmission is being tuned around a specific motor and spur gear combination. Warning! Not suitable for children under 14 years.
RC tuning parts
Pinion Gear Coated Alu 24T M0.6, RC spare gear
300054771€9.99
The Pinion Gear Coated Alu 24T M0.6 is a drivetrain spare part built for RC model setups that use 0.6 module gearing. Its aluminum body keeps the gear light, while the 24-tooth layout provides a defined gearing option for tuning or replacing a worn motor pinion in an existing transmission. A hard coating covers the tooth surface to handle repeated contact in the gear mesh, and the rounded tooth shape is specified to increase wear resistance while reducing friction loss in the drivetrain. The central bore mounts the gear on the motor shaft, and the included set screw secures it in place for accurate positioning against the spur gear. The 24 marking on the face makes identification straightforward during maintenance or parts changes. This spare gear suits workshop tasks such as refreshing a used RC drivetrain, correcting a damaged pinion, or preparing a matching motor-and-spur combination for the next run. In regular bench maintenance, the compact metal part is easy to sort, inspect and swap when the transmission needs the correct M0.6 pinion again. Warning! Not suitable for children under 14 years.
RC tuning parts
Servo Mount Short, RC chassis accessory, aluminum
300053596€15.49
The Alum. Servo Stays Short is a chassis accessory for TT-01D TYPE-E and TT-01 TYPE-E builds that places a small servo in a lower position. Machined aluminum construction brings high rigidity and accurate fit to this mounting point, helping the steering installation sit neatly within the chassis layout. The set is supplied as 1 short servo mount with 14 pieces. Alongside the aluminum stays, spacers are included for fine adjustment during installation. Those spacers also make it possible to attach a large servo, which broadens the range of compatible steering setups without changing the basic mount. The hardware shown in the set supports the fastening task directly, with washers and screws matched to the mount configuration. In workshop use, this accessory suits rebuilds, tuning work and replacement jobs on compatible TT-01 TYPE-E platforms. A lower servo position can be useful where chassis layout and linkage placement need a more compact arrangement, while the aluminum parts add a clean technical finish to the steering area. Warning! Not suitable for children under 14 years.
RC tuning parts
Suspension Mount Shim Set, RC tuning accessory
300054987€7.19
This suspension mount shim set adds a fast, precise tuning option to an RC chassis setup. The pack contains 20 shims in 2 measured thicknesses, 0.2 mm and 0.3 mm, with 10 pieces of each, so spacing changes can be matched more closely to the handling balance being dialled in at the suspension mount. Each shim uses a U-shaped profile that can be inserted after the mount screw is loosened, which avoids fully removing the fastener during setup work. The forked shape and circular seat help the shim sit around the fixing point in a controlled way, making small geometry changes easier to repeat from one adjustment to the next. The set is designed for use together with washers included in the chassis kit. Shaded and marked parts shown in the fitting diagram are not included in the set. On a workbench, this kind of measured spacing change helps when comparing one suspension setting against another or when refining left and right mount positions in small increments. It suits builders who want quicker access to setup variation during maintenance, testing and chassis tuning, while keeping the adjustment process focused on the mount area rather than a full strip-down.
RC tuning parts
TA-05/IFS Carbon Rein.F Parts, chassis parts
300054031€10.79
TA-05/IFS Carbon Rein.F Parts bring a focused chassis upgrade to compatible RC car builds by using carbon fiber-reinforced resin for the hub carriers. That material choice gives these parts a tougher structure than standard resin versions, with a more direct effect on steering feel when the car is loaded through turns and direction changes. The set is intended for the TA05-IFS and TRF416 chassis and is supplied as 1x F parts tree with 2 components. The paired layout supports left and right installation, matching the mirrored geometry needed at the wheel mounting area. In use, the stiffer carrier construction helps maintain alignment more consistently when the chassis is pushed through fast corner entries, linked bends and repeated steering inputs. This makes the parts relevant not only for replacement after wear, but also for tuning a car toward a more precise front-end response. On a workshop bench, the set suits planned maintenance on a TA05-IFS or TRF416 build where worn carriers are being swapped for reinforced versions. At the track, the sharper steering response can be felt in tighter line control and a cleaner handling balance through technical sections. Warning! Not suitable for children under 14 years.
RC tuning parts
TA-06 Alum. Cup Joint Gear Diff. Unit (2), RC part
300054532€22.29
This aluminum differential cup joint set is made for TA-06 drivetrain tuning, replacing the standard front or rear differential cup joints with lighter metal parts. The 2 output bevel differential cups cut 7.6 g compared with the standard kit joint cups, trimming weight from the drive system where rotating parts matter. Each cup joint works at the differential connection point where drive is passed into the shaft assembly, and the slotted cup form is designed for use with the matching blade parts. Pin protectors are included to reduce wear on the cup and shaft contact areas, which is especially useful in running conditions where repeated drivetrain load can mark the joint surfaces over time. The set is intended for TA06 Chassis, TA06 PRO Chassis and TA06 MS Chassis, giving a focused option for maintenance, replacement or weight-conscious setup changes within that platform family. Use this pair when refreshing a worn front or rear differential connection or when building a TA-06 configuration with closer attention to drivetrain mass. Depending on the chassis setup, a shorter driveshaft may be required.
RC tuning parts
TA-06 Cross Shaft, RC differential spare part
300054311€10.59
The TA-06 Cross Shaft Met. Bevelge.-Diff. is a compact RC differential spare part designed to replace the standard resin cross shafts in the kit-included differential gear unit of the TA06 chassis. The metal construction brings added rigidity to this high-load area and supports smoother operation as the differential turns through acceleration, braking and cornering. The scope of delivery contains 2 cone differential shafts, matching the paired layout used inside the differential assembly. Beyond TA06 fitment, the stated compatibility list extends to TD4, TD2, DB01, FF-04 EVO, M-08 CONCEPT, M-07 CONCEPT, TA06 MS, TA06 PRO, TA05 ver.II, TRF503, TRF211XM, TRF201XMW, XV-01, XV-01 PRO and XV-01T. For TA05 ver.II chassis, this part is used with 54312. For DB01 chassis, it is used with 54329. This spare part suits maintenance work, drivetrain refreshes and targeted upgrades where the differential is already being serviced. The small machined format also makes it a practical bench-stock component for keeping compatible chassis ready for the next rebuild or running session. Warning! Not suitable for children under 14 years.
RC tuning parts
TA-06 Steel Gear Diff. Unit Rear, RC spare part
300054471€40.99
The TA-06 Steel Gear Diff. Unit Rear brings a complete rear differential upgrade together for TA-06 based RC chassis, combining steel bevel gears and metal cross shafts in a drivetrain assembly made for the rear gearbox. Inside the housing, the bevel gears transfer drive across the axle while the cross shafts support the internal gear action, creating the controlled differential movement needed when cornering on track. The set groups the main assembly parts for this rear unit in one place, including a rear gear case set, a gear differential cup joint set, a gear differential gasket, 2 large bevel gears, 4 small bevel gears and a gear cross shaft. The gasket sits between the housing sections to help seal the differential during assembly. Cup joints connect the finished unit to the drivetrain, while the internal gear layout allows the left and right wheels to rotate at different speeds through turns. This makes the set useful for replacing worn parts or building a rear differential with steel internal gears instead of standard components. On TA06, TA06 PRO, FF-03R and XV-01 chassis, the unit suits workshop maintenance, race-day servicing and focused rear-end tuning. For standard FF-03 cars, item 54398 FF03 Gear Case for Gear Differential is required separately.
RC tuning parts
TA-06/XV-01 18 Teeth Alum. Pully, RC spare part
300054450€27.49
The TA-06/XV-01 18 Teeth Alum. Pully is a drivetrain upgrade part for Tamiya TA-06 touring car chassis and XV-01 crossover chassis platforms. Its 18-tooth aluminum construction brings a precise replacement for the standard pulley, while the high-lubricating coating on the surface is designed to improve transmission efficiency and durability during use. The compact assembly adds a focused mechanical change where belt drive performance matters most. The included hardware shown for the assembly consists of the pulley, spacer parts, a metal pin and an E-clip. For the XV-01 platform, the pulley can be installed at both front and rear positions, which supports consistent drivetrain setup across multiple mounting points. The instruction diagram shows the part used in place of the existing 18T pulley on TA-06, making it a direct specification match rather than a tooth-count change. Aluminum spacer elements support the installed position and help complete the pulley assembly as intended for the chassis layout. On a workbench build or maintenance session, this pulley suits focused transmission servicing, replacement of worn drive components, or a planned chassis upgrade. It fits naturally into tuning work where belt movement, rotating efficiency and precise fit are the priority within TA-06 and XV-01 running setups.
RC tuning parts
TA-07 Aluminum Motor Mt Posts, chassis upgrade
300054725€12.29
The TA-07 Aluminum Motor Mt Posts bring a focused chassis upgrade to TA07 PRO cars by replacing the standard motor mount parts with 2 blue anodized aluminum posts. Positioned at the main motor plate, these parts increase rigidity at a key mounting point, which helps support the motor more firmly when higher powered setups place greater load on the drivetrain. Each post is designed for use in place of part A15, making the change specific and direct rather than a broad rebuild. The machined aluminum shape creates a more solid attachment point than the standard resin pieces, and the anodized finish adds a clean technical look that matches performance-oriented tuning parts. The installation diagram specifies correct orientation and straight screw fitment, with thread lock applied during assembly. That detail matters at this location, where alignment at the motor plate affects how securely the parts seat against the chassis hardware. On a TA07 PRO build, this kind of upgrade suits drivers refining a car for stronger motor output and more controlled power delivery. It fits naturally into workshop sessions focused on drivetrain tuning, chassis response and targeted parts replacement, especially when a standard mounting point is being upgraded for a stiffer setup.
RC tuning parts
TA-07/TB-05 Soft Stabilizer Set for RC Chassis
300054979€35.49
The TA-07/TB-05 Soft Stabilizer set adds a focused suspension tuning option for compatible RC chassis cars by supplying 6 stabilizer bars with stepped stiffness choices for front and rear use. Front bars are included in 1.3 mm, 1.2 mm and 1.1 mm sizes, while rear bars come in 1.2 mm, 1.1 mm and 1.0 mm sizes, making it possible to adjust roll characteristics with a measured hardware change rather than broad setup guesses. The set uses stabilizer ends with integrated adjusters, a detail that keeps the assembly light and simplifies trackside setup work. That construction helps when comparing front-to-rear balance across repeated laps, because the bars can be fitted and adjusted with a direct mechanical reference. The included range supports fine changes instead of a single large step, which is useful when a chassis needs a narrower setup correction for changing grip levels or a specific circuit layout. Compatibility is stated for TA07, TB-05 and TRF420 chassis cars, placing the set squarely in the tuning category for on-road RC running. On practice days, club races or timed sessions, the different bar options support back-to-back testing through fast corners, linked direction changes and tighter infield sections where small setup differences can show up in lap consistency.
RC tuning parts
TA02/01 Alum. Motor mount Set, model accessory
319804966€35.49
The TA02/01 Alum. Motor mount Set adds a machined aluminium mounting solution to compatible model builds, centring the motor base around a circular plate with a wide middle opening and a ring of evenly spaced holes. This layout supports careful positioning during repair, replacement or tuning work and gives the drivetrain area a clean, technical fit. Alongside the main plate, the set uses threaded cylindrical spacers, a flanged adapter piece and a countersunk Phillips screw to create the motor base assembly. The metal parts shown in silver are shaped for screw-fastened installation, with countersunk openings that let the screw sit flush in the mount. The threaded sections support neat connection between the individual components, while the different spacer forms help establish the required stand-off and mounting height within the chassis area. On the workbench, this hardware suits rebuilds, maintenance sessions and targeted upgrades where a worn or standard motor base is being replaced with aluminium parts. The compact set focuses on the mounting zone itself, making it a practical choice for model hobby setups that need precise motor support rather than decorative add-ons.
RC tuning parts
TA08 Carbon Damper Stays FR, RC chassis parts
300022005€28.49
TA08 Carbon Damper Stays FR adds a focused suspension tuning option to compatible TA08 chassis cars with 2 carbon stays for the front and rear. Each stay is 3 mm thick and uses a lightweight plate format with multiple mounting points, giving the chassis a clear path to more precise damper geometry changes during setup. The front stay provides 4 damper attachment positions, while the rear stay provides 5, so adjustments can be made separately at each end of the car instead of relying on a single fixed mounting location. The set also contains 4 hex head screws in 3 x 6 mm size for installation. The carbon construction and machined hole layout suit builders who want to work directly with suspension settings and compare different damper angles on the same TA08 platform. On a bench setup, the different attachment points support careful testing of front-to-rear balance before the next run. At the track, the front and rear stays allow repeated setup changes with the same chassis base, making this set a useful choice for drivers refining handling on compatible TA08 cars.
RC tuning parts
TA08 LF King Pin Balls, RC chassis option parts
300022016€12.69
TA08 LF King Pin Balls bring a focused suspension upgrade to compatible RC chassis cars by replacing the standard 7 mm suspension balls and king pins with 4 low-friction aluminum components. The hard anodized finish changes the contact surface from the kit-standard steel setup and supports a more rigid suspension point where the upright moves through its travel. Each king pin ball reduces weight by about 0.4 g, trimming unsprung mass at a part of the chassis that reacts directly to steering and surface input. That reduction is small in absolute terms but meaningful at the suspension, where lighter moving parts can help the car settle more quickly and track more consistently through repeated corner entries. The set can be installed at either the front or rear, using 1 king pin ball at the top and bottom of each upright. Compatibility is stated for TC-01 and TA08 PRO chassis cars. A full setup for 1 kit requires 2 sets. When fitting this Hop-Up Option, new 51663 TC-01 C/D Parts Suspension 2 pcs and 51669 TA08 D Parts Suspension Arms 2 pcs are recommended. This makes the set a targeted choice for tuning an existing chassis with a clearly defined suspension change rather than a general-purpose hardware pack.
RC tuning parts
TA08 LW Front One-Way 37T, chassis upgrade set
300022039€66.99
The TA08 LW Front One-Way 37T is a chassis upgrade set for selected Tamiya on-road cars, built to alter front drivetrain behavior with a dedicated one-way mechanism. Installed at the front, the unit leaves the front wheels unbraked during deceleration, which changes how the car responds when power is applied and when entering corners. At the center of the set is an aluminum one-way housing paired with a slim lightweight 37T pulley. That layout focuses on a compact rotating assembly at the front end, while the included cup joints, urethane bushings and 3x5 mm hex head screws provide the hardware needed for the conversion. The one-way action is a mechanical tuning change rather than a cosmetic add-on, aimed at drivers refining acceleration response and corner entry on belt-driven chassis layouts. Compatibility is stated for TA08 PRO, TA07 and TRF420 chassis cars. This kind of front setup suits track sessions where steering response and exit speed are being tuned corner by corner. In workshop preparation or race-day maintenance, the set gives experienced builders a defined 37T front one-way option for platform-specific drivetrain adjustment.
RC tuning parts
TA08 Stabilizer Set F/R, chassis accessory kit
300022003€38.49
The TA08 Stabilizer Set F/R adds a focused suspension tuning option to compatible TA08 chassis cars by supplying front and rear anti-roll bar parts in 2 stiffness levels. Super soft green stabilizers and soft red stabilizers are both included, making it possible to alter roll response at each end of the chassis and match the car more closely to track grip and corner balance. The set contains long Open Face 5 mm reinforced adjusters, 5 mm stabilizer end adjusters, aluminum stabilizer rod supports, 5x10 mm aluminum hex head ball connectors, 630 ball bearings and 3x2.5 mm grub screws. That hardware gives the bars their mounting points and link connections while the bearings help the mechanism move smoothly through suspension travel. Using 2 front and 2 rear stabilizers keeps the setup specific to both ends of the TA08 layout rather than treating the chassis as a single undivided system. On a technical indoor layout or a higher-grip circuit, the different bar rates can be swapped to explore how the car settles into turns, changes direction and carries speed through linked corners. As a workshop upgrade, this set suits drivers who tune handling step by step and want a dedicated stabilizer package matched to the TA08 platform.
RC tuning parts
TA08R/Pro Alum. Diff.-Mount +0,5, RC chassis part
300022079€28.49
These aluminum differential holders are an option part for the TA-08 platform and related touring car chassis, adding a more rigid mounting point around the differential area while supporting accurate belt tension adjustment. The set contains 2 holders and uses a +0.5 specification that changes differential position compared with the standard layout. The rigid aluminum parts are designed to hold the adjustment notch securely, which helps the belt setting stay consistent under load. Their shape also supports smooth rotation at the differential area and improves rigidity where the holders connect with the bulkheads. In that section of the chassis, oil damper motion is transmitted more directly to the main structure, which can help the suspension response stay more faithful to the setup. Laser engraving distinguishes these holders clearly from Item 22079, which uses a different offset. Compatibility covers TA08R, TA08 PRO, TRF420X and TRF420 chassis. Depending on surface conditions, the alternative 0.5 mm offset holder arrangement can be relevant for setup tuning, and a raised differential position is stated to stabilize the car on high-grip surfaces. On a prepared track, that gives builders another precise chassis setting to match grip level and drivetrain feel.
RC tuning parts
TA08R/Pro Alum. Diff.-Mount +0.8, chassis option part
300022078€28.49
These aluminum differential holders are a focused chassis upgrade for TA08R, TA08 PRO, TRF420X and TRF420 builds. The 2-piece set adds a 0.8 mm offset and gives the differential section a rigid mounting point, while the integrated notch works with belt tension adjustment for a more exact drivetrain setup. Under load, the aluminum construction helps limit deformation at the connecting sections with the bulkheads. That added rigidity supports smooth differential rotation and helps oil damper motion transfer properly into the chassis, so suspension input is carried more directly through the assembly. Laser engraving distinguishes this version clearly from Item 22079, which uses a 0.5 mm offset. Depending on surface conditions, that alternative offset can also be used as part of setup tuning. On high-grip surfaces, differential height becomes an important setup variable, and raising the differential can stabilize the car. That makes these holders a useful option when refining belt tension, comparing offset choices and preparing a TA08R or TRF420 platform for track-specific handling changes.
RC tuning parts
TA08R/Pro Alum. Motor Mount, chassis option part
300022081€39.99
The TA08R/Pro Alum. Motor Mount is a chassis option part for TA08 PRO and TA08R platforms, built around a 3.0 mm TA08R aluminum motor plate and matched mounting hardware. Its machined form and countersunk screw positions suit precise installation in the motor area, where fit and alignment matter during a rebuild or tuning update. The set contains 1 aluminum motor plate, 2 aluminum upper deck mounts and 2 countersunk 3x6 mm hex head screws. The blue anodized finish gives the metal parts a clear technical look while keeping the focus on the component geometry, including the cutouts and mounting points needed for the chassis layout. As an option part, this set is aimed at maintenance, replacement or setup changes on an existing compatible chassis rather than a complete vehicle build. Used during workshop servicing or a focused chassis refresh, the parts support a direct hardware update on TA08 PRO and TA08R assemblies. The compact contents make it suitable for racers and model builders who keep specific spare and tuning parts ready for platform-based maintenance. Warning! Not suitable for children under 14 years.
RC tuning parts
TA08R/Pro Rear Upper Arm Mount Set, RC chassis part
300022084€60.79
This aluminum rear upper arm mount set is an option part for the TA08R and TA08 PRO chassis, supplying 2 mirrored pieces for the left and right sides of the rear assembly. The machined shape, multiple mounting holes and slotted section create a precise interface where the upper arm area meets the chassis, giving builders a focused upgrade for this section of the car. The set is described as a chassis aluminum rear upper arm mount and is intended for model tuning rather than general replacement across unrelated platforms. Its geometry is specific to the TA08 family, and the pair format ensures the rear section receives matching hardware on both sides. Dedicated attachment points also support the separately sold TA08R Carbon Upper Deck in 2.0 mm thickness, which opens an additional configuration route for builders working with TA08R-based layouts. During bench setup, the design allows easier attachment and detachment of upper arm ball connectors, which is useful when rear suspension parts need to be accessed repeatedly for maintenance or adjustment. Compatibility is stated for the TA08 PRO and TA08R chassis, making this set a direct fitment choice for those specific platforms. Warning! Not suitable for children under 14 years.
RC tuning parts
TA08R/Pro Rein. Rear Body Mounts, chassis option part
300022085€28.29
This rear body mount set is an option part for TA08R-based chassis setups and brings the key hardware for a focused shell mounting update into one pack. The set combines 2 carbon fiber bases with 2 aluminum posts, creating a rear mounting structure that supports accurate body placement and a tidy fit around the shell line. The included body mount extensions, carried over from Item 54604, allow mount height adjustment according to the body in use. That makes the set useful when shell shapes or mounting positions differ, because the rear posts can be set to suit the body rather than forcing a fixed height. Small hardware is also supplied for installation, with 2 3x6 mm hex head screws, 2 3 mm washers and 2 7 mm snap pins completing the package. The mix of carbon fiber, aluminum and fastening parts keeps the upgrade centered on the rear body mounting area instead of spreading across unrelated chassis sections. Compatibility is stated for the TA08 PRO, TA08R and TB Evo.8 chassis, making this set a direct choice for those platforms when rear shell mounting needs replacement or adjustment. On a finished RC touring car, that can help when setting body height and securing the shell cleanly at the rear mounting points. Warning! Not suitable for children under 14 years.
RC tuning parts
TA08R/Pro Upper Arm Mount Set, aluminum chassis part
300022083€60.79
This aluminum front upper arm mount set is made for the TA08 PRO and TA08R chassis and supplies a matched left and right pair for the front section. The mirrored parts use a hole pattern and slotted geometry shaped for the chassis connection area, giving the assembly a dedicated option part focused on front-end tuning and maintenance access. A key function of the set is its provision for the separately sold TA08R Carbon Upper Deck in 2.0 mm thickness. The added attachment points make that deck compatible with this mount layout, which is useful for builders refining a TA08R or TA08 PRO setup with model-specific chassis parts. The aluminum construction brings a precise machined look to the front assembly, while the left and right format keeps the installation matched across both sides. Content is 2 pieces. During workshop use, the easier attachment and detachment of upper arm ball connectors can simplify repeated setup work at the front end. That matters when camber or suspension-related adjustments call for frequent access around the upper arm area. As an option part rather than a universal accessory, this set is intended specifically for TA08 PRO and TA08R chassis builds and upgrade projects. Warning! Not suitable for children under 14 years.
RC tuning parts
TB Evo.IV/TRF416 D-Parts, suspension arm set
300051104€17.29
The TB Evo.IV/TRF416 D-Parts suspension arm set is a dedicated carbon spare part for selected RC touring car chassis, built to restore the correct fit where suspension components take repeated load. Supplied as 1 D-parts set with 2 parts, it gives a direct replacement route for maintenance work on compatible platforms. Fitment covers FF-03, FF-03 PRO, TA05 Ver.II, TB-04, TB-04 PRO, TB-03, TB-03 VDS, TT-02 TYPE-SR and TT-02 TYPE-S chassis. That wide chassis coverage makes the set useful for keeping several workshop builds in service with the same reference part. The suspension arm shape uses defined mounting holes and cutout sections to match the intended chassis layout. In running gear assembly, this kind of component links key suspension points and helps preserve the geometry set elsewhere on the car. On the bench, the set supports routine replacement after wear, damage or a full teardown. It also suits planned rebuilds where the correct D-parts are needed before the next setup session, helping compatible chassis return to smooth, consistent operation with the intended arm structure. Warning! Not suitable for children under 14 years.
RC tuning parts
TB-04 Bevel Gear Set, RC chassis spare parts
300054593€7.19
This TB-04 bevel gear set brings carbon fiber-reinforced resin construction to a key drivetrain area, giving TB-04 chassis cars gears that are more resistant to wear and suited to use with higher-powered motors. The set is made up of 3 matched transmission parts that work together where rotational force changes direction inside the chassis. A 40T ring gear handles the larger driven stage, while the 16T bevel gear and 20T miter gear complete the meshing set for the TB-04 layout. The angled teeth on these gears are designed to engage under load as the drivetrain transfers power through the chassis, making correct fit and matched tooth contact especially important. Because the parts are specified as a set, installation as a complete group helps maintain the intended relationship between the gears rather than mixing single replacements into an existing worn setup. This spare parts set suits maintenance, repair and drivetrain refresh work on compatible TB-04 chassis cars. It fits naturally into workshop sessions focused on restoring clean gear action after running with stronger motor setups or replacing worn internal transmission parts with the correct matched components.
RC tuning parts
TC-01 Alu. Steering Arms L/R, RC chassis parts
300054958€35.99
The TC-01 Alu. Steering Arms L/R brings a focused steering upgrade to TC-01 chassis cars with a left and right aluminum arm set finished in blue anodizing. Designed as a hop-up option for the freshly released TC-01 platform, these parts support smoother handling while giving the front steering assembly a more precise mechanical feel. The set replaces the kit-standard components T4 and T7, using lightweight aluminum parts in their place at a key point in the steering mechanism. That material change gives the mounting area a more secure attachment and adds a more direct response through steering inputs. The machined shape and mounting holes are tailored to the TC-01 layout, so the upgrade stays specific to the chassis it is made for instead of relying on a generic fit. For a matching setup within the same steering area, use with the aluminum steering bridge in item 54957 is recommended. On the bench, this pair suits builders refining a TC-01 car with selected metal hop-up parts rather than changing the whole chassis at once. Bearings are not included, so the set can be planned into a build, maintenance session, or steering refresh with the required hardware already on hand.
RC tuning parts
TC-01 Alu. Steering Bridge, chassis hop-up part
300054957€28.79
The TC-01 Alu. Steering Bridge is a focused hop-up part for TC-01 chassis cars, replacing the kit-standard T9 component with a precision aluminum bridge that adds rigidity to the steering area and supports smoother handling. Its blue anodized finish gives the machined part a clear visual identity while matching the technical character of a tuned chassis build. The bridge is supplied as 1 aluminum component and is designed to sit between the steering parts shown in the TC-01 layout. The mounting holes and central slot allow accurate positioning during installation, while shim adjustment can be used to set clearance so the steering bridge and arms move smoothly. The instruction data also recommends gel type thread lock on the screws to help prevent loosening, and 630 ball bearings are recommended for the steering assembly. Recommended for use with the aluminum steering arms in Item 54958. Compatible with TC-01 chassis cars. On a bench build, this part suits targeted chassis tuning where the steering system is being refined one section at a time. In running sessions, the added rigidity and cleaner steering movement support a more settled response through direction changes on a TC-01 setup.
RC tuning parts
TC-01 Alum. Damper Extenders, chassis hop-up set
300054960€9.29
TC-01 Alum. Damper Extenders bring a focused suspension upgrade to TC-01 chassis cars with 4 lightweight aluminum components shaped for damper mounting. The blue anodized finish gives the set a crisp technical look while the precision-machined construction targets a more exact hardware fit in a high-spec chassis setup. As a Hop-Up Option, this set is aimed at builders refining how the suspension is configured rather than changing the character of the whole car at once. Each extender replaces the kit-standard version with an aluminum alternative, shifting this area of the assembly from standard molded hardware to machined metal parts. That makes the set a clear tuning step for TC-01 builds where damper function and suspension detail matter. The pack contains 4 matching extenders, allowing the same specification to be carried across the chassis instead of updating only one corner. On the bench, the set suits planned rebuilds, fresh TC-01 assemblies, or targeted suspension revisions between running sessions. The matched parts and chassis-specific compatibility make it a straightforward choice when the goal is a cleaner, more consistent damper setup on a TC-01 platform.
RC tuning parts
TC-01 Alum. Rocker Arms, chassis hop-up parts
300054955€19.99
The TC-01 Alum. Rocker Arms (2) bring a focused suspension upgrade to TC-01 chassis cars by replacing the kit-standard rocker arms with lightweight aluminum parts. Their higher rigidity reduces flex at the linkage, which helps the suspension react with a more direct feel when the chassis loads and unloads through corners, braking and acceleration. Each set contains 2 aluminum rocker arms and is intended as a hop-up option for builders refining the suspension character of a TC-01 machine. The change in material affects how force passes from the suspension linkage into the dampers, so damper action feels cleaner and more immediate than with the standard molded parts. The blue anodized finish adds the familiar technical look associated with Tamiya tuning parts while also marking the upgrade clearly during maintenance and setup. This set suits targeted chassis tuning, whether the goal is a sharper response on a prepared track or a more defined suspension feel during test sessions in a car park. For a complete front and rear rocker arm conversion on 1 car, 2 sets are required.
RC tuning parts
TC-01 DblCrd Prop Shaft, chassis hop-up part
300054961€35.99
The TC-01 DblCrd Prop Shaft is a dedicated hop-up part for TC-01 chassis cars, built to support more efficient drive with a double cardan layout that maintains true rotation across a range of operating angles. Crafted in steel, the shaft replaces the kit-standard propeller shaft parts with a more rigid driveline component suited to tuning the chassis around its moving suspension geometry. The set is supplied as parts for assembling 1 shaft, not a full front and rear conversion. That makes it a focused upgrade for builders working on a specific driveline position first, while keeping the option to match the chassis with a second set later. The included shaft length shown in the documentation is 54 mm, and the assembly uses joint pieces, pins and axle rings to create the finished rotating linkage. The double cardan mechanism is especially relevant where the shaft must transmit power cleanly while the angle changes through steering and suspension movement. Installed on a TC-01 car, this hop-up part suits workshop tuning sessions that concentrate on driveline efficiency rather than cosmetic changes. It also fits rebuilds where worn standard parts are being replaced with a steel alternative matched to the chassis platform.
RC tuning parts
TC-01 Stabilizer Set, RC chassis option parts
300054956€27.29
The TC-01 Stabilizer Set adds a focused suspension tuning option to TC-01 chassis cars by introducing sway control that supports steadier cornering balance. With 3 rod rates in 1.1 mm, 1.2 mm and 1.3 mm, the set gives a clear path to adjusting chassis response for different surfaces and driving styles while keeping the installation compact within the car layout. Each rod sits between the upper cover and the chassis, where clearance can be adjusted via 3 x 3 mm grub screws. Aluminum hex head ball connectors make setup changes easier when comparing different stiffness choices. The black rods use red, yellow and blue markings so each rate can be identified quickly during bench work. The stabilizer can be installed at the front or the rear, which allows targeted tuning of entry feel and mid-corner balance on a TC-01 build. On practice days or race preparation sessions, the set supports back-to-back setup testing with a direct hardware change rather than a full suspension redesign. One set equips either the front or the rear; 2 sets are required to complete one car with front and rear sway bars. Compatible with TC-01 chassis cars.
RC tuning parts
TC-01/TB Gear Different, aluminum shaft set
300054533€9.99
This shaft set is made for the TC-01/TB gear differential and supplies 2 matching aluminum parts for maintenance, repair or parts replacement in a model drivetrain. The compact format and dedicated fit make it a focused choice when a differential assembly needs the correct metal component rather than a generic substitute. Each piece has a cylindrical profile with a darker central hex section, indicating a layout designed to locate securely within the relevant differential area during assembly. Aluminum construction keeps the parts light while providing the crisp, machined character expected for RC model hardware. Because the set contains 2 identical shafts, both sides of the intended mechanism can be refreshed with matching components instead of mixing old and new drivetrain parts. In workshop use, this kind of spare is well suited to routine servicing, rebuilds after heavy running sessions, or keeping essential replacement parts on hand between maintenance intervals. It also fits neatly into a planned parts stock for TC-01/TB based builds where drivetrain condition and exact component matching are part of careful setup work.
RC tuning parts
TC-01/TB-04 Gear Diff. Steel Bevel Gears
300054540€20.49
TC-01/TB-04 Gear Diff. Steel Bevel Gears are drivetrain spare parts for compatible Tamiya chassis, centered on the internal gear differential where controlled power distribution depends on clean, accurate gear engagement. The steel construction gives these bevel gears the material specification stated for the set, making them suited to differential rebuilds and scheduled parts replacement on used running gear. Within a gear differential, bevel gears work at the core of the mechanism, transferring drive through meshing angled teeth while allowing the left and right sides of the axle system to rotate at different speeds in turns. That makes this set relevant when a TC-01 or TB-04 build shows wear in the diff internals or when a fresh drivetrain setup is planned during maintenance. The designation covers 2 chassis families, so the parts can be matched directly to those platforms instead of relying on generic hardware. As a model supply in the Models & Accessories range, the set is aimed at repair, upkeep and chassis-specific workshop use. On the bench, these gears suit routine differential servicing, a full gearbox refresh, or a rebuild after extended running. They also fit neatly into a spares box for future maintenance on TC-01 and TB-04 cars, where having the correct internal metal gears on hand helps keep a project moving without delay.
RC tuning parts
TD4 Aluminum Steering Arms, RC car accessory
300022033€39.99
These TD4 aluminum steering arms are a focused chassis upgrade for TD4 cars, combining machined metal construction with built-in ball bearings to sharpen steering feel at the front end. The set includes a left arm and a right arm, each shaped for its position, with the blue anodized finish giving the parts a clean technical look once fitted on the chassis. The aluminum structure keeps weight low while providing firm attachment at the mounting points, which helps the steering linkage transmit input with a more direct response. Built-in ball bearings support the pivot area and promote smoother movement through the steering action. The long cutout profile and compact arm shape reflect the purpose of the part: reducing excess mass while keeping the component ready for repeated running sessions on a TD4 platform. Installed on a TD4 chassis car, the pair suits maintenance, repair or a move from standard parts to a metal steering setup. The matched left and right layout keeps the front steering assembly consistent, whether the goal is restoring worn hardware or refining the control feel of an active RC buggy.
RC tuning parts
TD4 Ball-Diff. Nut/Screw Set, RC spare parts
300022029€11.29
The TD4 Ball-Diff. Nut/Screw Set brings together the small mechanical parts used in a TD4 ball differential, giving RC model maintenance a focused hardware pack instead of a search through mixed workshop stock. The set contains a shouldered screw, a coil spring, washers, a blue metal retainer piece and 8 steel balls, all centered on the differential assembly shown in the designation. Within a ball differential, these parts work as a pressure and contact system: the spring loads the assembly, the screw provides the fastening point, the washers sit between moving or clamped surfaces, and the steel balls form the running contact elements inside the mechanism. That combination matters when a differential needs fresh hardware after wear, disassembly or a lost part during service. The blue anodized component adds a dedicated fitted part to the set rather than relying only on generic screws and washers. On the bench, this kind of pack supports a clean rebuild of the TD4 differential with the exact group of small components kept together in one place. It suits routine maintenance sessions, targeted repairs after drivetrain wear, or preparation of a spare parts box for future servicing on a compatible RC chassis.
RC tuning parts
TRF 1050 Sealed Ball Bearings, RC spare part
300042366€9.29
The TRF 1050 Sealed Ball Bearings set adds a focused drivetrain and running upgrade to model applications that rely on clean, accurate rotation. Each bearing uses a rubber-sealed design and low-friction oil inside the race, combining smooth movement with a construction that can be opened for servicing when dirt and residue build up over time. The set contains 2 bearings and is suited to locations such as uprights, where steady support around a rotating shaft helps the surrounding assembly run more cleanly. The rubber seals differ from metal-sealed versions by allowing access to the internal bearing surfaces for maintenance work. That makes it possible to clean the bearing, refresh lubrication and return it to service instead of treating it as a closed component. In use, the ball bearing construction also improves fit compared with plastic and metal bearings, which helps reduce resistance in moving parts. On a workshop bench, during a rebuild, or as part of a running upgrade, these bearings suit model setups where precise rotation and service access both matter. They work well for replacing worn standard bearings in assemblies that see repeated movement and need a more exact mechanical response.
RC tuning parts
TRF 1150 Sealed Ball Bearings, RC spare part
300042377€9.99
TRF 1150 Sealed Ball Bearings are a compact RC spare part for maintenance, replacement and fresh assembly work where smooth, controlled rotation matters. The 2-piece set provides a matched pair of bearings with blue seals and metal outer rings, making it suitable for compatible mounting points that need consistent fit and even running. The sealed construction is the key working feature here: each bearing encloses its rolling elements behind the seal, helping limit the entry of dust and debris during use. That matters anywhere an axle or shaft turns repeatedly, because cleaner internals support steadier movement through the assembly. The metal bearing rings provide the firm contact surfaces needed for accurate seating in the relevant housing. In workshop use, a matched pair also simplifies servicing when both sides of a rotating assembly need replacement at the same time. This bearing set fits naturally into regular RC upkeep, whether a model is being refreshed after repeated runs or assembled with new running gear. On the bench, the pair format keeps replacement work straightforward; in use, the sealed design supports smooth mechanical action in the parts these bearings are built to serve.
RC tuning parts
TRF 44mm Double Cardan Joint Shaft RC Spare Part
300042216€72.99
The TRF 44mm Double Cardan Joint Shaft set brings a more controlled drivetrain feel to RC chassis that run direct couplings, using 2 joint sections per shaft to cut rotational vibration where it starts. That layout helps the suspension work with less disturbance as power passes through the driveline, which is especially useful when a spool is fitted in place of a differential. Each shaft is made from high-strength steel and matches the overall length of a standard 44 mm universal drive shaft, so the upgrade keeps the intended drivetrain dimensions while changing the joint design. The set contains 2 shafts, and the instruction data shows related assembly details such as grease application, left and right axle ring orientation, and use with thin 1050 ball bearings at 3 mm thickness where required by the chassis layout. If the upright contacts the shaft, the marked section can be trimmed to clear rotation. This spare part suits maintenance work as well as targeted drivetrain tuning on compatible RC models. Each component is available separately as a spare part, which supports servicing worn sections instead of replacing the full assembly after extended running sessions.
RC tuning parts
TRF 5mm O-Ring Set, gear differential spare
300042259€4.99
The TRF 5 mm O-Ring red set is a drivetrain spare for oil-filled sealed gear differentials, built to support a cleaner seal inside compatible assemblies. Its key difference is the slightly smaller inner diameter compared with the standard black kit O-ring, creating a tighter fit where differential oil needs to stay contained during use. This pack contains 8 red O-rings and is intended for many sealed gear differential units across the Tamiya range. The data specifically names the TA-05 option sealed gear set, plus the included differential sets used in TA-06, XV-01 and TRF417 series cars. That makes the set useful both as a direct replacement during maintenance and as a practical stock part for workshop drawers, pit boxes or ongoing chassis service. In oil-filled differentials, small sealing parts have a direct effect on how consistently the unit holds fluid, so the ring size matters. During rebuilds or routine servicing, these O-rings slot into the differential assembly as functional sealing components rather than cosmetic extras. They suit racers and builders who keep multiple compatible chassis in rotation and want the correct red 5 mm rings ready when a differential is opened for inspection or refresh work.
RC tuning parts
TRF 5mm Reinforced Adjuster, RC chassis part
300054257€5.89
The TRF 5 mm Reinforced Adjuster is a chassis part for compatible RC buggy platforms where linkage points face repeated load during driving. Its reinforced construction is intended for buggies that take heavy loads, while the special low-friction resin helps the adjuster move smoothly at the connection point. In the workshop or during a rebuild, that combination supports clean, controlled fitting on the chassis models listed for this part. This set comes in grey and contains 8 ball sockets, with each adjuster sized at 5 mm. The shape shown for each piece uses a long stem and rounded ball end, suiting the compact hardware layout common to competition-focused buggy chassis. Compatibility is stated for TD4, TD2, DB02, DB01, DN-01, TRF503, TRF502X, TRF211XM, TRF201XMW and TRF201 chassis, so the same pack can cover replacement needs across several established platforms. The multiple-piece count also suits keeping matching spares ready between maintenance intervals. On a fresh build, the 8-piece set can be fitted across the required linkage points on a supported chassis. During servicing, worn adjusters can be swapped for matching 5 mm replacements to keep movement consistent across the assembly. Warning! Not suitable for children under 14 years.
RC tuning parts
TRF 850 Sealed Ball Bearings, RC accessory, 2 pcs
300042368€8.49
TRF 850 Sealed Ball Bearings bring smooth rotation and precise fit to compact RC drivetrain positions where clean running and efficient movement matter. The 2 included bearings use rubber seals instead of metal seals, giving the assembly a serviceable design that can be opened for cleaning when dirt and residue build up around frequently used running gear. Inside each bearing, low-friction oil lubricates the internal workings to support freer movement during operation. In place of plain plastic or metal bearings, the ball bearing construction helps rotating parts run with greater efficiency and a more exact fit at the mounting point. The 850 size suits compact transmission and shaft locations where small tolerances affect how directly power moves through the assembly. Applications named in the data include the center shaft area on TRF420 and TA07MS chassis, as well as M-chassis gears. These bearings fit naturally into maintenance routines for RC cars that are driven regularly and stripped for cleaning between sessions. They also suit targeted upgrades in worn or high-use drivetrain areas, where a fresh pair of sealed bearings can restore cleaner rotation and more consistent mechanical response.
RC tuning parts
TRF Big Bore Dampers+ (4), touring car damper set
300042354€97.99
TRF Big Bore Dampers+ brings the TRF419 damper design into a touring car tuning set built for sharper suspension response and stronger track grip. The 4-damper package uses cylinders that are 0.5 mm wider than standard, increasing oil volume by 10% and giving the damping action a steadier feel through repeated corner entries, direction changes and acceleration zones. Each damper is built around HL cylinders, titanium-coated shafts and transparent silicone O-rings, a combination that supports smooth movement and reliable sealing inside the assembly. Aluminum spring retainers work with the threaded adjusters to fine-tune spring tension and ride height, while the overhauled reinforced V parts expand setup choices for different surface conditions. The internal layout uses 3-hole big bore pistons, oil seals, rod guides and urethane bushings, giving experienced builders more scope to refine how the chassis settles, rolls and transfers weight. Damper oil and silicone oil are required separately. On a touring car chassis, that extra tuning range becomes useful when the setup needs to react to changing grip levels between practice sessions and race runs. A bench build can focus on oil fill, piston movement and preload settings, then move straight to track testing where the suspension can be adjusted corner by corner for a more planted feel.
RC tuning parts
TRF Cross Joints, universal shaft parts, 2-pack
300042357€4.29
These TRF Cross Joints are built to reduce friction and wear in universal shaft setups, using a low-friction fluorine coating on each joint to support efficient motion where the driveline is under constant load. The pack contains 2 cross joints and the matching pins and grub screws needed for attachment, keeping the hardware aligned with the intended installation. The compact metal parts are shaped for use with compatible universal drive shafts, where the cross joint forms the moving connection between shaft sections. As the shaft rotates, the joint and pin arrangement allows motion to pass through the assembly while the fluorine coating helps limit contact wear at the working surfaces. That makes this set a practical choice for replacing tired hardware or refreshing a driveline that has seen repeated running sessions. The included grub screws secure the assembly in place, and the included pins complete the joint connection without requiring separate attachment hardware from the start. In workshop use, these parts suit routine maintenance, driveline servicing and targeted replacement of worn joint hardware on compatible model car setups. They also fit builds where efficient power transfer and reduced friction at the universal shaft connection are a priority.
RC tuning parts
TRF Damper Rod Guide&O-Ring (4), damper set
300053574€10.39
The TRF Damper Rod Guide&O-Ring (4) is a damper service set for TRF Touring Car dampers, built around machined fluororesin rod guides, spacers and low-friction silicone O-rings. Inside the shock, these parts support smoother piston rod movement and help keep the damping action feeling clean and controlled during maintenance refreshes. The scope of delivery contains 12 damper accessories. Clear rubber O-rings handle the sealing role, while fluorine bumper guides add a dedicated contact part within the damper assembly. This set is intended for rebuild and conversion work rather than a complete shock replacement, making it a focused choice when internal wear parts need attention. The listed fitment reaches across multiple chassis families, including XV-01, XV-01T, TA07 MS, TA07 MSX, TA06, FF-03, TB-03, TA05-Ver.II, TC-01, TT-02, TT-02D, TT-02 TYPE-S, TT-02 TYPE-SR, TT-01 TYPE-E, TT-01D TYPE-E, TT-02RR and TT-02FT. Further compatibility is also stated for M-07 CONCEPT, M-08 CONCEPT, F103GT, F104, F104W, DF-03, DB01 and DB02 with the specified companion parts. On the bench, the set suits scheduled damper servicing, chassis refresh work and targeted replacement of internal shock components before the next running session. Warning! Not suitable for children under 14 years.
RC tuning parts
TRF Sh. Damper Spring Medium, RC spring set
300053631€7.79
The TRF Sh. Damper Spring Medium adds a focused suspension tuning option for compatible RC chassis, using a medium spring rate and a free length about 5 mm shorter than the hard spring from the OP440 street specification. That shorter length lowers vehicle height, which supports added stability during higher-speed running and gives setup work a more planted base. This set contains 2 matching coil springs and is intended for use with Item 53571 TRF Damper Set with fluorine-coated dampers. Across compatible FF, M, TA, TB and TT chassis, the spring choice broadens the available adjustment range when combined with other springs in the setup. The yellow finish makes the pair easy to identify on the bench or during maintenance, while the matched format suits left and right damper installation on the same car. Compatibility includes FF-03, FF-03 PRO, FF-04 EVO, M-07 Concept, TA05 Ver.II, TA06, TA06 PRO, TA06 MS, TA07 PRO, TA07 MS, TB-03, TB-03 VDS, TB-04, TB-04 PRO, TB-05 PRO, TT-01 Type-E, TT-01 Type-ES, TT-01D Type-E, TT-02, TT-02D, TT-02 Type-S and TT-02RR chassis. On a tuning bench or at the track, this spring pair supports quick suspension changes when a lower ride height and a different damping balance are needed.
RC tuning parts
TRF Sh. Damper Spring Soft, RC damper springs
300053630€7.79
The TRF Sh. Damper Spring Soft is a suspension tuning part for compatible RC chassis and is supplied as a pair of red metal coil springs. Its softer setup and shorter free length support a lower vehicle stance, which helps settle the chassis during faster on-road running and gives suspension tuning another clear direction to explore. These springs are intended for use with the 53571 TRF damper kit with fluorine-coated dampers. Compared with the hard spring from the OP440 street specification, the free length is about 5 mm shorter, which lowers vehicle height and broadens the available setup range when combined with other spring options. Compatibility spans a wide group of chassis including FF-03, FF-03 PRO, FF-04 EVO, M-07 Concept, TA05 Ver.II, TA06, TA06 PRO, TA06 MS, TA07 PRO, TA07 MS, TB-03, TB-03 VDS, TB-04, TB-04 PRO, TB-05 PRO, TT-01 Type-E, TT-01 Type-ES, TT-01D Type-E, TT-02, TT-02D, TT-02 Type-S and TT-02RR. In workshop use, the pair suits setup changes aimed at refining ride height and suspension response for different track conditions. The springs can be fitted as part of a broader damper tuning routine when a chassis needs a lower stance and a wider spring combination range. Warning! Not suitable for children under 14 years.
RC tuning parts
TRF Super Short Big Bore Dampers, RC damper set
300042353€99.99
TRF Super Short Big Bore Dampers+ brings a focused suspension upgrade to touring car chassis built around Super Short Big Bore damper geometry. The set provides the parts for 4 dampers and combines a compact 6.5 mm shorter format with a cylinder interior that is 1.2 mm wider than TRF Special Dampers Item 42102, a layout aimed at high-grip, technical circuits where quick direction changes and corner speed matter. The damper package uses HL coating cylinders, silicone O-rings, POM resin pistons, aluminum spring retainers and titanium-coated piston rods. Black super soft springs are included, along with 4 blank pistons and 4-hole pistons for setup changes that alter how the suspension reacts under load. The reinforced V parts introduced with Item 54871 broaden the available tuning range further through revised designs and materials. Blue anodized aluminum parts give the assembled dampers a clear competition look while keeping the hardware easy to identify during bench work. On a touring car prepared for this damper format, the shorter body and big bore layout suit technical track sections with frequent braking zones, linked corners and fast transitions. Compatible damper stays and Item 42344 are required separately for use.
RC tuning parts
TRF418 Rein. Arm Hub Carrier 4° RC spare parts
300054580€10.99
The TRF418 Rein. Arm Hub Carrier 4° is a suspension upgrade part shaped for RC chassis that use short reversible suspension arms and double-cardan swing shafts. Its carbon reinforced construction and built-in 4° caster combine fitment-focused design with a geometry change aimed at tighter, lower-speed track sections. The carrier is made to avoid contact with double-cardan shafts during use, which helps preserve free movement at the front end where steering angle and shaft clearance matter most. Direct attachment to the Item 53928 Short Reversible Suspension Arm set keeps installation aligned with the intended suspension system. Compatibility is stated for cars fitted with Item 53928 Short Reversible Suspension Arms, including TB-03, TB-04, TB-04, TA-05, TA-06, FF-03, TRF 416 and TRF 417. In workshop setups focused on technical circuits, the 4° caster angle gives a concrete tuning option for lower-speed corners and smaller layouts. Supplied as a pair, these hub carriers suit maintenance, replacement or chassis-specific setup changes where suspension geometry and shaft clearance need to work together.
RC tuning parts
TRF419/418 Rear Uprights, RC spare parts
300054570€6.89
The TRF419/418 E-Parts Rear Upr. set supplies 2 rear uprights for 1/10 touring car maintenance, using the same carbon fiber-reinforced material found on the TRF418 chassis kit. Each upright is molded with the mounting points and pivot geometry needed at the rear suspension corner, where alignment and smooth movement matter during setup and running. This set is intended for Tamiya 1/10 touring car models fitted with short reversible suspension arms. The listed compatibility covers TB-03, TA-05 Version II, TA-06, TRF416 and TRF417 chassis, giving a clear route when replacing worn rear suspension parts on those platforms. The reinforced material choice supports the role of the upright as a link between suspension arms, axle hardware and the rest of the rear assembly. Supplied as a left and right pair, the 2-piece format suits a complete rear-corner refresh on one axle line. On a workshop bench, these E-Parts fit naturally into routine chassis upkeep, rebuilds after race wear, or a planned spares stock for touring car running. For drivers maintaining several compatible Tamiya platforms, the named chassis list makes it easier to match the set to the correct rear suspension layout.
RC tuning parts
TRF420 DC Axle Shafts, RC spare part set
300042363€18.79
These TRF Axle Shafts for TRF420 DC are a dedicated RC spare part set for the revamped universal shafts used on the TRF420 chassis. Supplied as 2 axle shafts, they provide a direct way to replace this exact drivetrain component when wear, damage or a rebuild calls for fresh parts at the axle end. The shafts are designed for compatibility with double cardan drive shafts, which makes them relevant for TRF420 DC running gear maintenance and targeted drivetrain servicing. Their separate release means this specific part can be sourced on its own instead of replacing a complete universal shaft set. That keeps parts selection focused on the component actually needed for repair or upkeep. The product data also states an important fitment note for cross-chassis use: when these shafts are installed on chassis other than the TRF420, 4 mm thickness bearings are required. On the bench, this 2-piece set suits planned maintenance, damage replacement and parts stocking for an existing TRF420 DC setup. It also gives builders working across compatible chassis a clear reference for the extra 4 mm bearings needed when adapting the shafts beyond the original TRF420 application.
RC tuning parts
TRF420 Steel F Direct Cups, RC chassis parts
300054934€19.19
TRF420 Steel F Direct Cups bring a focused drivetrain upgrade to compatible Tamiya touring car chassis, combining steel construction with extra front-end mass for a more deliberate tuning setup. Each cup weighs 8 g, which is double the weight of the kit-standard aluminum part, so the change is not only about material but also about how weight is placed at the front of the car. The pair is designed for the front drivetrain area, where repeated contact and impact can put stress on rotating parts. Steel gives these cups a stronger basis for that duty, while the included swing shaft caps complete the set with the matching companion parts listed for installation. This is a 2-piece direct cup set rather than a mixed assortment, keeping the upgrade specific to one drivetrain position. Compatibility is stated for TA07 MS, TA07 PRO, TRF419, TRF419X, TRF419XR and TRF420 chassis. In workshop tuning, the added 8 g per cup can be used when a build calls for more weight toward the front of the chassis. On track, that makes this set a practical option for racers refining setup changes through clearly defined hardware rather than improvised ballast.
RC tuning parts
TRF420 TA-08 TA-07 Gear Diff Shim Set
300042313€3.59
The TRF420/419X/TA-07 Gear Diff Shim Set is a focused tuning set for oil-filled gear differentials in compatible TA07 PRO, TRF419 and TRF419X chassis. These large-diameter shims are inserted into the differential internals, where they adjust the position of the spider gear assembly and support a more exact internal setup during maintenance or rebuild work. The set provides 3 dedicated shim sizes for differential tuning: 5 x 15 x 0.3 mm shims, 5 x 15 x 1 mm shims, and 2.6 x 9.5 x 0.1 mm shims. That size spread allows fine changes to spacing rather than a single broad adjustment, which is useful when dialing in gear engagement inside an oil-filled unit. The larger outer diameter suits the intended differential application, and the mixed thicknesses give a practical range for setup work across compatible chassis. On the bench, this shim set supports routine differential service, rebuilds, and setup corrections when gear mesh needs closer adjustment. It also suits racers and builders keeping spare tuning parts ready for drivetrain maintenance, especially when reducing skipping is part of protecting the internal gears from avoidable damage. Warning! Not suitable for children under 14 years.
RC tuning parts
TRF420/419 Swing Shaft Caps, RC spare parts
300054921€4.79
The TRF420/419 Swing Shaft Caps are reinforced replacement parts for the shaft area on compatible chassis, created to hinder wear where repeated movement puts stress on small drivetrain components. Supplied as a 2-piece set, they suit maintenance work that focuses on keeping a race setup precise and responsive over time. These caps are intended for the TRF420 and TRF419 platform and are changed regularly as part of normal upkeep when the original parts show wear. Their compact role in the assembly makes them easy to overlook, yet they directly support the condition of the surrounding shaft hardware during repeated use. The reinforced construction is the key detail here, because it addresses wear at the contact point rather than changing the layout of the car. The set is also specified for use with Item 54879 TRF419 Aluminum Front Direct Cups (2pcs.), which gives a clear compatibility reference for matching front-end configurations. In a workshop setting, this 2-piece pack fits neatly into a spares box for scheduled servicing between runs. On race days, fresh caps can be swapped in during routine checks to keep the drivetrain area ready for the next session. Warning! Not suitable for children under 14 years.
RC tuning parts
TRF420/419/TA-07 Alu Steering Arm Set, RC option parts
300054704€35.99
The TRF420/419/TA-07 Alu Steering Arm Set brings a focused steering upgrade to compatible Tamiya chassis with 2 lightweight aluminum arms, a rigid construction and pre-inserted 850 ball bearings. In a fast on-road setup, that combination supports sharper front-end response and a more connected feel through direction changes. The parts share the proven TRF419 race machine design and are intended to replace the standard A4 steering arm position shown in the chassis layout. Each arm uses a larger bearing seat at one end and a threaded mounting point at the other, with 3 x 5 x 0.2 mm shims and 3 x 0.7 mm spacers used in the installation sequence shown in the fitting diagram. The blue anodized finish gives the steering area a clear visual match with other alloy hop-up parts. For matching setup, use is recommended with the TA07 Aluminum Steering Bridge. On a TA07 PRO, TRF419 or TRF419X build, this set suits drivers refining steering precision for higher-speed laps and cleaner line changes. The 2-arm format makes it a direct left and right upgrade for the front steering assembly, with the bearings already in place for fitting. Warning! Not suitable for children under 14 years.
RC tuning parts
TRF420/419/TA07 Gear Diff Unit Set, RC spare parts
300051649€41.99
The TRF420/419/TA07 Gear Diff Unit Set brings a complete 37T gear differential build into one spare-parts package for RC chassis maintenance and drivetrain tuning. Black housing parts, internal bevel gears, shafts, O-rings, shims, gasket and screws come together as a sealed differential assembly that can be built, filled with silicone oil and fitted into a compatible belt-drive layout. The differential pulley and case use a slimmer design that saves 1.5 g compared with predecessor units, reducing weight in this rotating assembly. The construction is also more oil-tight than earlier versions, helping the silicone oil stay around the bevel gears where it controls differential action. Assembly uses the included gasket, O-rings, pins and shims to seal, space and secure the unit. The instruction sequence shows oil filling until the gears are covered, then fastening the pulley side with screws for a compact 37T differential layout. On the bench, multiple units can be built with different oil viscosities and kept ready for circuit changes or setup testing. The set fits TRF420 directly, while TRF419 and TA07 installations use shims to adjust bearing position, pulley position and clearance for the chassis in use.
RC tuning parts
TRF421 45mm Rear Swing Shafts, RC spare parts
300042385€14.79
These 45 mm lightweight rear swing shafts are specified for the TRF421 chassis kit and supply 2 matching replacement parts for the rear drivetrain. The 90 degree offset between the drive pin and cross shaft positions is stated to limit vibration while driving, giving this small component a direct role in how the chassis transfers power under load. Each shaft is intended for the rear section, so the fitment stays focused on the exact area named in the data rather than a general drivetrain swap. The lightweight construction concentrates on a rotating part of the assembly, where mass and balance matter during running. With 2 pieces in the set, both sides of the rear end can be serviced with matching parts. The 45 mm length is the stated specification, which keeps replacement work aligned with the original chassis requirement. This spare part suits routine maintenance, repair after wear, or a planned rebuild of a TRF421 setup. During track preparation or workshop servicing, the pair can be fitted as the designated rear swing shafts to restore the intended drivetrain layout. The compact format also makes them a practical addition to a race box built around TRF421 running parts. Warning! Not suitable for children under 14 years.
RC tuning parts
TT-01 Alum. Prop. Joint & Shaft RC chassis part
300054026€21.29
This aluminum propeller joint and shaft set upgrades the center driveline of TT-01 series RC chassis with a direct rotating connection and a clean blue anodized finish. Designed as a replacement for kit-standard resin parts, the set supports efficient power transfer between the front and rear sections of the chassis while adding a more technical metal component at the core of the drivetrain. The 3-part set consists of 1 propeller shaft with front and rear propeller joints. In the drivetrain layout, these parts take over the job of linking the central shaft to the surrounding transmission components, so rotation passes through the chassis with the aluminum parts in place of the original molded pieces. The set is compatible with TT-01 Type-E, TT-01 Type-ES and TT-01D Type-E chassis, and the instruction material also identifies use as spare parts for TT-01R chassis. Installed in a touring car build or used during drivetrain maintenance, the set suits chassis refreshes, targeted upgrades and replacement work on worn center shaft parts. The blue finish stands out clearly during bench work, and the matched shaft-and-joint layout keeps the upgrade focused on the exact components used in the middle of the driveline. Warning! Not suitable for children under 14 years.
RC tuning parts
TT-01 Ball Bearing Set, RC chassis bearings
300053497€40.99
The TT-01 Ball Bearing Set brings a low-friction upgrade to compatible RC chassis builds by replacing standard bearing parts with 16 metal ball bearings. As rotating shafts and axles run through shielded bearing races instead of plain bushings, the drivetrain can turn with less resistance and a freer feel during driving. This set contains 12 x 1150 bearings and 4 x 1280 bearings. The bearing sizes are arranged as a complete pack for the stated chassis application, so the key rotating points can be equipped with matching parts from one set. Ball bearings are a common tuning step for RC models because they support more efficient transfer of motor power through the transmission and wheel assemblies. The scope of delivery contains 1 ball bearing set with 16 pieces. On the bench, the set suits maintenance, repair or a fresh chassis build where smoother running is the goal. Once fitted, the reduced drag can help the model roll and drive with improved efficiency, making this upgrade a practical choice for regular track, car park or off-road RC use. Warning! Not suitable for children under 14 years.
RC tuning parts
TT-01 Spur Gear Set, RC drivetrain gears
300053665€15.48
The TT-01 Spur Gear Set adds 55T and 58T gearing options to supported TT-01 chassis, giving the drivetrain a clear route beyond the standard 61T setup. Both gears are molded with the tooth count on the part itself, which keeps identification straightforward when comparing ratios at the workbench or during routine transmission service. This set is intended for TT-01 Type-E, TT-01 Type-ES and TT-01D Type-E chassis. The central mounting area uses a splined fitting, and the gear faces feature a reinforced 4-lobed hub section that supports stable installation in the transmission assembly. Used as tuning parts or replacement parts, the 55T and 58T gears let builders alter how the car responds on different layouts by changing the final drive relationship inside the drivetrain. Pairing with separately sold 22T, 23T, 24T or 25T pinion gears expands the available combinations further. On faster circuits, a smaller spur gear can help shift the setup toward more speed, while other ratios can be chosen to suit tighter sections and repeated acceleration zones. The set also works well as a workshop spare for TT-01 owners who like to keep multiple gearing options ready between running sessions. Warning! Not suitable for children under 14 years.
RC tuning parts
TT-01 Turnbuckle Tie-Rod Set, RC chassis accessory
300053662€11.99
The TT-01 Turnbuckle Tie-Rod Set adds direct adjustability to supported TT-01 chassis builds, using a hex center section that changes rod length with a simple turn. That layout allows toe-in and toe-out correction on the model, which keeps setup work fast when steering alignment needs a small change before the next run. This 13-piece set is intended for the TT-01D TYPE-E chassis, TT-01 TYPE-E chassis and TT-01 Type-ES chassis. The turnbuckle shafts work with rod ends and ball connectors to create adjustable links with pivoting movement at the mounting points. Because the adjuster does not need to be removed for length changes, alignment work stays more precise and less disruptive than rebuilding a fixed link. The included wrench supports the center-section adjustment and hardware tightening during installation and maintenance. On a workshop bench, the set suits routine chassis tuning, steering correction after parts changes, or preparation for different track layouts. Between runs, small toe-angle changes can be made quickly to refine straight-line stability or turn-in response on compatible RC touring car setups. Warning! Not suitable for children under 14 years.
RC tuning parts
TT-01/02 Damper Set, RC chassis upgrade, CVA Mini
300053619€42.99
The TT-01/02 Damper Set with 4 CVA Mini shock units brings oil-filled suspension tuning to compatible Tamiya touring car chassis. Replacing kit-standard friction dampers, the cylinders deliver more efficient shock absorption and a more controlled response when the model runs over uneven sections, transitions and corner entries. Each of the 4 dampers is built for use on TT-01 Type-E, TT-01 Type-ES and TT-01D Type-E chassis. The key tuning advantage comes from the oil-filled design: different separately sold oil viscosities can be used to alter damping feel, making it possible to tailor suspension movement to surface grip and handling preference. This turns the set into more than a replacement part; it is a practical chassis upgrade for builders who want finer setup options than the standard friction damper layout can provide. On a workbench, the set supports suspension rebuilding and setup changes with a clear mechanical purpose. Once fitted to a compatible chassis, the 4 matching dampers help create a more even suspension response across the model, whether the focus is regular running, maintenance or incremental tuning between sessions. Warning! Not suitable for children under 14 years.
RC tuning parts
TT-01/DF-02 Alum. Motor Mount, RC spare part
300053666€14.99
The TT-01/DF-02 Alum. Motor Mount is a dedicated RC spare part for selected Tamiya chassis and combines secure motor attachment with a built-in heat sink effect. Made of aluminium and supplied as 1 motor mount, it brings a focused mechanical upgrade or replacement to the drivetrain area where stable positioning matters. Its die-cast construction gives the mount the rigid form needed for installation in compatible platforms, while the central opening and mounting points are shaped for its specific role inside the chassis layout. The part is intended for DF-02, TT-01D TYPE-E and TT-01 TYPE-E chassis, making it a direct choice when worn hardware needs replacement or when a standard mount is being swapped for an aluminium version. As a single dedicated component, it suits maintenance benches, rebuild projects and chassis-specific parts storage without adding unrelated extras. In use, the mount supports tidy workshop repairs and planned upgrades on compatible RC car builds. It fits naturally into service tasks such as replacing a damaged mount, refreshing an older chassis or preparing a model for repeated running sessions where firm motor seating and heat transfer both matter. Warning! Not suitable for children under 14 years.
RC tuning parts
TT-01E Ball Bearing Set, RC car accessory
300054025€46.99
The TT-01E Ball Bearing Set brings a focused drivetrain upgrade to compatible TT-01 Type-E based chassis by replacing friction-heavy rotating points with 20 metal bearings. With 12 size 1150 bearings and 4 each in 1280 and 850, the set is arranged for the bearing positions used in the TT-01 Type-E, TT-01 Type-ES and TT-01D Type-E platforms. In use, ball bearings help the drivetrain turn with less resistance than plain bushings, so more of the motor's output reaches the wheels instead of being lost through drag. The set also includes the bearing sizes used around the steering posts, where freer rotation supports a more direct response at the front end. That makes this upgrade relevant not only for straight-line efficiency but also for the feel of directional inputs during corner entry and line changes. As a tuning step, it targets the mechanical areas that influence rolling efficiency and steering precision without changing the basic chassis layout. This set suits a fresh TT-01 Type-E build as well as a running chassis that is being refined part by part. On indoor tracks, car parks or smooth outdoor surfaces, the reduced drivetrain resistance can contribute to cleaner acceleration and a more settled response through repeated laps. Warning! Not suitable for children under 14 years.
RC tuning parts
TT-02 Alum. Racing Steering Set RC Upgrade Parts
300054574€55.99
The TT-02 Alum. Racing Steering Set brings a rigid aluminum steering layout to TT-02 chassis builds, replacing standard steering parts with blue anodized metal components that focus on cleaner input transfer at the front end. The set centers on 2 matching steering arms with installed pivot hardware, supported by dedicated posts, flanged bushings, screws, set screws and washers arranged for the steering section they serve. The machined aluminum construction gives this upgrade part its character, with each arm shaped for the steering mechanism rather than as a decorative add-on. Black inserts at the arm ends and the central pivot hardware show how the assembly is built to mount and move through its steering arc. The included flanged bushings and screw set support accurate fit at the connection points, while the matched pair format suits the left and right sides of the steering assembly. As a chassis-specific option for the TT-02 platform, this set fits naturally into tuning work that focuses on steering precision rather than broad cosmetic changes. On an assembled RC touring car, that translates into a front end that reacts through a firmer linkage path when direction changes come quickly on smooth track surfaces or car park running lines. It also suits maintenance work on an existing TT-02 build where the steering section is being refreshed with metal replacement parts instead of standard components.
RC tuning parts
TT-02 Alum. Rear Upright 2.5°, RC chassis part
300054549€48.99
The TT-02 Alum. Rear Upright 2.5° brings a focused chassis tuning change to TT-02 machines by replacing the standard rear uprights with an aluminum pair that sets the rear toe angle to 2.5°. That geometry change targets steering response through a concrete suspension adjustment rather than a cosmetic upgrade, making it a useful option when refining how the rear end behaves in corners. The set consists of a dedicated right and left upright, marked 2.5A and 2.5B for clear side identification during fitting. Each part uses an anodized blue finish and a machined shape built around the hub or bearing opening and the mounting points used at the rear suspension arm area. In the standard TT-02 layout, the kit resin parts A11 run at 0°, while this pair introduces 2.5° of toe-in when installed in their place. The metal construction adds rigidity at this mounting point, where alignment accuracy matters to repeatable setup changes. On a workbench, the marked left and right parts make setup changes easier to track between maintenance sessions or handling experiments. Once fitted to a TT-02 chassis, the altered rear alignment supports more deliberate cornering behaviour and gives hobby users a direct way to tune the chassis with a clearly defined geometry change.
RC tuning parts
TT-02 Alum. Steering Bridge, RC chassis upgrade
300054575€29.99
The TT-02 Alum. Steering Bridge is a focused chassis upgrade for TT-02 and TT-02B builds, replacing the standard A5 steering part with a blue anodized aluminum component. The metal construction brings greater precision and toughness to the steering area, supporting more exact handling when the front linkage is working under load. This part is installed in the steering servo assembly area, where the bridge mounts to the chassis and links into the steering mechanism. The set contains 1 aluminum steering bridge as well as shims and small attachment parts for installation. The instruction data shows 3 x 12 mm screws and 3 x 0.1 mm shims at the mounting points, where spacing is adjusted to suit the assembly. A B11 insert and the D6 support area are part of the illustrated fitment layout, with the steering servo positioned beneath the bridge assembly. On a compatible RC chassis, this upgrade suits builders who want a more exact front-end response from the steering system rather than a cosmetic change alone. It fits naturally into a workshop session focused on tuning, maintenance or replacing the standard steering bridge with a more rigid aluminum alternative. Warning! Not suitable for children under 14 years.
RC tuning parts
TT-02 Aluminium Propeller Joint, chassis option part
300054502€10.99
The TT-02 Aluminium Propeller Joint is a focused drivetrain upgrade for TT-02 chassis builds that replaces the standard resin joint parts with blue anodized aluminum components. Fitted at the front and rear propeller shaft connection points, the 2 matching joints help reduce power loss in the transmission so more of the drive reaches the wheels during running. Their role sits deep in the driveline, where small losses at rotating connection points can affect how efficiently power moves through the chassis. The aluminum construction gives these option parts a more exact interface than the stock resin version, making them a useful choice for maintenance, tuning or a planned parts upgrade. The blue anodized finish also makes the modified driveline easy to identify during servicing. These joints are designed specifically for the TT-02 platform and pair naturally with other compatible transmission upgrades in the same chassis family. On a fresh build, they support a more considered drivetrain setup from the start. On an existing TT-02 car, they offer a straightforward way to refresh front and rear shaft connections while keeping the original chassis concept intact.
RC tuning parts
TT-02 Aluminium Propeller Shaft, chassis accessory
300054501€8.99
The TT-02 Aluminium Propeller Shaft is a dedicated chassis accessory for TT-02 builds, replacing the kit-standard resin shaft with an aluminium version shaped for more stable rotation at higher speeds. In running sessions where the driveline is working harder, that steadier rotation helps reduce power loss through the transmission and keeps the transfer of drive more consistent. The shaft is finished in Tamiya blue anodized aluminium, giving the part a clean machined surface as well as a distinct visual match for other tuned chassis components. A laser-engraved TAMIYA marking is applied directly to the shaft, making the upgrade easy to identify on the bench during fitting, inspection or parts changes. The pack contains 1 TT-02 aluminium propeller shaft, keeping the change focused on a single driveline component rather than a broad rebuild. This kind of option part suits builders refining a TT-02 chassis step by step, whether the goal is a sharper setup for higher-speed running or a more precise driveline specification. It also works well when replacing a worn standard shaft with a metal alternative that is made specifically for the same chassis layout.
RC tuning parts
TT-02 Aluminum Motor Heat Sink, RC chassis part
300054571€16.49
The TT-02 Aluminum Motor Heat Sink is a compact cooling upgrade for TT-02 series RC chassis, pairing a finned aluminum body with a curved slide-on form that sits directly on a 540 motor. By increasing the surface area around the motor can, it helps heat dissipate more efficiently during use and supports steadier running under load. The blue anodized finish gives the part a crisp machined appearance, while the open clamp shape is designed for straightforward mounting as shown in the instruction leaflet. Compatibility is stated for TT-02, TT-02B and TT-02D chassis. The leaflet also specifies use with Type 540 motors, RS-540 Sport Tuned Motor and RS-540 Torque-Tuned Motor, and notes that certain motor types must not be used where the terminals could contact the heat sink and cause a short circuit. When fitted on TT-02 series chassis, parts D7 and D8 are removed before attachment. This chassis part suits bench upgrades, rebuilds and running maintenance where motor temperature management matters over longer sessions. It also works well for builders refining a TT-02 series setup with functional aluminum hardware that adds cooling support without changing the basic motor layout.
RC tuning parts
TT-02 Aluminum Servo Mount, chassis upgrade part
300054977€28.29
The TT-02 Aluminum Servo Mount is a chassis upgrade part that brings a more rigid steering foundation to compatible TT-02 chassis cars. Its one-piece aluminum construction replaces the standard separate A12 pieces, helping the steering section hold its shape more firmly during direction changes and supporting more precise servo motion. The mount uses an integrated design rather than a multi-part standard layout, which changes how the steering area is braced within the chassis. A blue anodized finish gives the machined aluminum a crisp technical look, while the laser-engraved logo adds a clean visual detail to the installed part. Included 3x8 mm screws and 3 mm washers provide the attachment hardware listed for fitting the mount to the chassis. Installed in a TT-02 build, this part suits drivers who want to refine steering response through a more rigid servo mounting point. It also fits well into a detail-focused upgrade plan where finish, fit and steering accuracy matter as much as the visible chassis hardware.
RC tuning parts
TT-02 Carbon Bumper Support, chassis accessory
300054814€11.29
The TT-02 Carbon Bumper Support is a chassis accessory for TT-02 and TT-01 Type-E touring car platforms, built around a 2 mm carbon fiber plate that brings a lighter and more rigid front support section. Its elongated shape, rounded ends, 4 circular mounting holes and 2 angled center slots match the task of securing the bumper area with a clean, purpose-built part. This support installs in place of TT-02 B7 or TT-01 Type-E D4 parts, making it a direct hardware swap for compatible cars rather than a broad chassis conversion. The carbon fiber construction gives the part a stiff structure at a key mounting point, which helps keep the bumper attachment more secure during running. Compatibility is specific: it fits TT-02 and TT-01 Type-E chassis cars and cannot be used on TT-02B. On the bench, it suits a focused refresh of a worn front section or a tuning step aimed at trimming mass without changing the overall chassis layout. In a rebuild or parts upgrade, the single support keeps the work centered on the bumper mount and the original fixing points of the compatible touring car chassis.
RC tuning parts
TT-02 Carbon Dstay II, RC chassis stay, 3.5mm
300054947€28.79
The TT-02 Carbon Dstay II is a 3.5 mm carbon fiber damper stay for TT-02 chassis cars, created as a stiffer suspension component for front or rear installation. The woven carbon plate and revised hole layout give the chassis a firm mounting point while opening more room for setup changes at the damper tower. Compared with Items 54639 and 54640, this version is 0.5 mm thicker, bringing added rigidity to a central suspension area without changing the core TT-02 fitment concept. The new design is also compatible with the adjustable front upper arms in Item 54874, a fitment point that the earlier Item 54639 does not offer. The set contains the stay plus collars and attachment hardware, and the instruction data shows mounting positions for both TRF dampers and friction dampers. Use with Item 53571 TRF Damper Set (Fluorine Coated) is recommended. TT-02B and TT-02 Type-S chassis are excluded, and this stay is also not compatible with Items 54000 and 42305. On a bench build, the 4 attachment positions allow measured suspension changes without replacing the stay itself. During chassis tuning, the same part can be fitted at the front or rear to support different damper layouts on compatible TT-02 cars.
RC tuning parts
TT-02 CVA Super-Mini Set, RC damper set, 4 pcs
300054753€36.99
The TT-02 CVA Super-Mini Set adds oil-filled damping to TT-01 and TT-02 chassis cars, bringing steadier suspension action when the car crosses uneven ground. With parts for 4 CVA Super Mini dampers and matching medium springs, the set gives a complete front and rear shock conversion in one pack. Each black spring is marked with yellow paint for quick spring-rate identification, which helps keep setup changes clear during tuning or maintenance. The assembly uses damper oil inside the cylinder, where the piston moves through the fluid to control compression and rebound more smoothly than a basic friction setup. The instruction sequence shows the piston rod, O-rings, oil seal and cylinder cap working together to seal the unit and maintain consistent damping action. Ball connectors and mounting hardware are provided to fit the completed dampers in place of standard dampers and screws on compatible chassis. On a running TT-01 or TT-02 machine, that oil-filled action helps the car settle more cleanly over bumpy sections and hold its line with more composure. For builders making a first suspension upgrade, this set focuses on one clear area of chassis tuning and adds a matched 4-damper package that can be assembled and installed as a dedicated hop-up.
RC tuning parts
TT-02 High Speed Gear Set 68T, chassis gear set
300054500€15.19
The TT-02 High Speed Gear Set 68T is a drivetrain option part for TT-02 chassis builds that shifts gearing toward faster setups while keeping the conversion focused on a few dedicated components. At the center is an FF-03 PRO 68T spur gear in module 0.6, paired with a newly designed aluminum spur gear mount and a 7 x 5 x 11.4 mm spacer for the assembly. This set enables gear ratio settings from 9.82:1 to 6.55:1. The instruction data also shows revised motor attachment positions on the D9 plate when a Type 540 motor is used, because the 68T tooth count changes the mounting position compared with the standard chassis manual. A stainless steel 2 x 9 mm shaft is included for the conversion, and the gear assembly is secured with the dedicated mount rather than reusing the standard 70T arrangement. The set is compatible with all TT-02 chassis, making it a focused upgrade for builders refining transmission response through gearing changes rather than broad chassis modification. On the bench, this gear set suits planned tuning sessions where pinion choice and motor position are adjusted together. It can also be used with a separately sold 64T spur gear to reach lower ratios, adding another gearing route for TT-02 setups built around different track demands.
RC tuning parts
TT-02 HT ServoSaver & Alu.Horn, RC steering set
300054799€20.49
The TT-02 HT ServoSaver & Alu.Horn is an RC steering upgrade set for TT-02 chassis variants that combines a hi-torque servo saver with a dedicated aluminum servo horn. This layout helps shield the internal servo gears from impact loads while sharpening the connection between servo output and steering linkage for a more direct feel at the wheels. The set includes 1 black Hi-Torque Servo Saver, 1 TT-02 Aluminum Servo Horn and attachment screws. The aluminum horn is designed specifically for the TT-02 platform, so it matches the steering layout used across the chassis family. In use, the servo saver spring assembly takes the force from sudden steering knocks instead of passing it straight into the servo geartrain. That makes it a useful choice when the steering system sees repeated curb taps, barrier contact or rough direction changes during track sessions. The parts are intended as a replacement for the standard chassis kit servo saver components. Mounted in a TT-02 touring car, buggy or truck conversion based on the same chassis family, the set supports a more precise steering connection while keeping the protective function of a servo saver in place. It suits rebuilds, maintenance work and targeted steering updates where the focus is on response, fit and gear protection rather than a full chassis overhaul. Warning! Not suitable for children under 14 years.
RC tuning parts
TT-02 Low Friction Suspension Ball, RC chassis part
300054559€9.49
The TT-02 Low Friction Suspension Ball is a chassis tuning part for TT-02 and TT-02B models, created to reduce resistance where the suspension pivots. Compared with the standard resin balls, the low-friction material gives the linkage a smoother action, which helps the suspension move more freely as the upright changes angle through travel. The set contains 4 matching suspension balls and is used in place of the specified standard parts in the suspension assembly. The instruction sheet shows each ball being inserted from the side marked with a circle symbol, with care taken not to mark the ball surface during fitting. It also notes that the front upright should remain free to move, so the fixing screw must not be overtightened. These details make the part's role clear: it forms a cleaner pivot point inside the suspension linkage rather than changing the chassis layout itself. This upgrade suits routine maintenance, a fresh build based on the TT-02 platform, or a setup refresh focused on suspension response. On a workbench, the 4-piece set supports a straightforward swap at the relevant mounting points and adds a more fluid feel to the moving suspension parts once assembled. Warning! Not suitable for children under 14 years.
RC tuning parts
TT-02 SRX Alu PropJointt & SS Cap, chassis parts
300022066€11.79
The TT-02 SRX Alu PropJointt & SS Cap set brings a tuned driveline update to compatible TT-02 chassis cars with 2 aluminum propeller joints and optional swing shaft caps. The blue aluminum parts are shaped for direct use in supported chassis layouts, giving the center driveline a component set intended for replacement of standard kit parts where specified. Each aluminum propeller joint offers 2 slot widths, so the setup can be configured with or without the swing shaft caps depending on the chosen arrangement. The set also includes 1 TRF417 V5 Swing Shaft Cap, and the data notes that this service part should be replaced periodically. When fitted, the swing shaft caps limit wear on joint cups and propeller shafts, which makes them a functional addition rather than a cosmetic extra. Compatibility covers TT-02, TT-02D, 1/10 R/C First Try R/C Kit with On-Road TT-02 Chassis, plus TT-02 Type-S and Type-SR chassis cars. In the stated applications, the parts are used in place of kit-standard C5 or E2 parts. The set is also recommended for use with the TT-02 Aluminum Propeller Shaft, making it a focused option for maintenance, replacement, or a driveline parts update on supported 1/10 on-road builds.
RC tuning parts
TT-02 Steering Parts Set, RC chassis upgrade
300054752€83.99
The TT-02 Steering Parts Set brings a focused steering upgrade to a stock TT-02 chassis machine by replacing the kit-standard steering parts with option components made for the same platform. Aluminum steering arms, aluminum steering posts and a steering bridge reshape the linkage area, while the Hi-Torque Servo Saver and the dedicated TT-02 Hi-Torque Servo Saver Horn complete the conversion around the servo connection. The set is built around the steering mechanism itself rather than cosmetic changes. In the assembly layout, the steering bridge connects across the steering arms with ball connectors and shims, and 2 turnbuckles are made to a 38 mm length for the linkage. The instruction data also shows a 5 mm adjuster trimmed by 2 mm before fitting to a 3 x 18 mm turnbuckle shaft, giving the linkage a defined build dimension. A range of metal attachment parts and setup hardware is included to support installation and steering adjustment on the chassis. On the bench, this upgrade suits a rebuild of worn standard parts as well as a first move into TT-02 option tuning. During setup, the dedicated horn and servo saver arrangement helps match the steering linkage to the chassis layout, keeping the work centered on the front steering assembly rather than a full vehicle rebuild. Warning! Not suitable for children under 14 years.
RC tuning parts
TT-02 Type-S Carbon Damper Stay Front, RC chassis part
300054632€24.99
The TT-02 Type-S Carbon Damper Stay Front is an RC chassis upgrade part that brings a stiffer carbon fiber structure to the front damper area. Mounted in place of the standard fiberglass stay, it supports more effective damper movement and gives the front suspension section a more rigid mounting base during running and setup work. The plate uses a symmetrical carbon fiber layout with multiple round holes, elongated slots and lower mounting tabs to position the front dampers and related hardware at the shock tower area. Included small parts such as ball connector nuts are supplied for attachment. The instruction diagram specifies 3 x 12 mm screws, 3 x 8 mm screws, 5 x 6.55 mm ball connector nuts and 5.5 x 3.0 mm spacers for the mounting sequence, while shaded chassis parts shown in the diagram are not included in the set. The part is designed for the TT-02 Type-S chassis platform. On a TT-02 Type-S build, this front carbon stay suits tuning work focused on suspension response and mounting rigidity. Use with a standard TT-02 chassis requires separately sold reversible suspension arms, the TT-02 Type-S Aluminum Suspension Mount Set and oil dampers.
RC tuning parts
TT-02 Type-S Carbon Damper Stay Rear RC Part
300054633€26.79
The TT-02 Type-S Carbon Damper Stay Rear is a chassis upgrade part that brings a stiffer carbon fiber mounting point to the rear suspension area of the TT-02 Type-S. By replacing the standard fiberglass stay, it increases rigidity around the dampers and supports more effective damper movement when the chassis loads up through corners and direction changes. The plate uses a wide rear stay shape with multiple round holes and slotted mounting positions, giving scope to adjust damper attachment points with precision. That layout helps fine-tune rear suspension geometry rather than locking the setup to a single fixed position. Small attachment parts are included in the set, including ball connector nuts, screws and a spacer, matching the hardware shown for the standard mounting position. The carbon fiber construction also keeps the part focused on tuning accuracy at the shock tower area. Installed at the rear of the chassis, this upgrade suits builders refining a TT-02 Type-S for circuit running and setup work. It can also be used with a standard TT-02 chassis when separately sold reversible suspension arms, the TT-02 Type-S Aluminum Suspension Mount Set and oil dampers are added.
RC tuning parts
TT-02 Type-SRX Gearbox Joints, RC spare parts
300022065€16.79
The TT-02 Type-SRX Gearbox Joints set is a drivetrain spare parts upgrade for race-focused TT-02 Type-SRX chassis setups. Its 2 aluminum gearbox joints use low-friction anodized surfaces to keep the transmission running with less resistance, supporting smoother power delivery when the drivetrain is under load. The included TRF417 V5 swing shaft cap works with the joints to reduce wear at the contact points between joint cups and drive shafts. That makes this set useful not only for replacement work, but also for keeping a tuned chassis consistent through repeated running and maintenance cycles. Compatibility is stated for the TT-02 Type-SRX chassis and for TT-02 chassis used with Item 22049. The metallic joint parts and the cap are supplied as separate components for installation into the drivetrain assembly. This set suits bench servicing, race-day maintenance and planned parts changes between running sessions. The swing shaft cap is a periodic replacement part, and the set is intended for race cars rather than heavy-duty use, so setup and use should match that application.
RC tuning parts
TT-02-S Alu. Upper Arm Mt., RC chassis parts
300054651€29.29
The TT-02-S Alu. Upper Arm Mt. set brings a precise suspension tuning change to TT-02 Type-S specification cars through 2 blue anodized aluminum mounts. By changing the height of the turnbuckle upper suspension arms, these parts alter suspension stroke and let chassis handling be adjusted with a more exact setup change at the mounting point. Each mount can be installed at the front or rear of the TT-02 Type-S chassis, which gives the same pair of parts flexibility within that specific platform. The set uses mirrored left and right mounts and comes with the small attachment parts needed for fitting. Blue anodized aluminum combines low weight with a rigid metal structure at a heavily used suspension area. That material choice also adds reinforcement at the upper arm mounting position, where repeated setup work and running forces act on the chassis. On a bench build, these mounts suit focused setup work around suspension geometry rather than cosmetic change alone. Once fitted, they support handling adjustments for drivers refining how the TT-02 Type-S responds through different running conditions while staying within the dedicated Type-S specification compatibility stated for the set.
RC tuning parts
TT-02-S Steel Rebound Stopper, chassis accessory
300054638€21.79
The TT-02-S Steel Rebound Stopper is a focused suspension tuning part for TT-02 Type-S chassis setups. Mounted to the TT-02 Type-S suspension mounts, each steel stopper works as a physical limit for rebound stroke, helping the car resist bottoming out while running and giving a more deliberate suspension setting on the bench and on track. The set contains 2 steel rebound stoppers and is intended for use with the TT-02 Type-S suspension mounts found in Item 54634 or sold separately as Item 54636 for the front and Item 54637 for the rear. Installation uses the same basic arrangement at both ends of the chassis, so front and rear rebound settings can be matched or adjusted according to the required setup. This makes the part useful for drivers refining suspension travel rather than changing springs or dampers alone. On a standard TT-02 chassis, use requires TT-02 Type-S suspension mounts, a damper stay and oil dampers sold separately. In a workshop setup or between race sessions, this small steel hardware set adds a direct way to tune how far the suspension extends, with a change that can be felt in how the chassis settles over uneven sections and under load.
RC tuning parts
TT-02/B Alum. Motor Mount, chassis accessory
300054558€22.99
The TT-02/B Alum. Motor Mount blue anodized is a chassis upgrade part for TT-02 and TT-02B based builds, combining a high-precision aluminum structure with direct fit replacement for the standard mount. The blue anodized finish and laser-marked positions give the part a technical look while keeping adjustment points easy to read during installation. Designed for TT-02, TT-02B, TT-02FT, TT-02RR, TT-02D, TT-02 TYPE-SR and TT-02 TYPE-S chassis, the mount is supplied as 1 motor mount with screws for attachment to the chassis. The central opening and numbered hole layout support accurate motor positioning around the pinion settings marked 16, 17, 18, 19 and 20. In use, the metal mount holds the motor more securely than the kit-standard resin part, which helps the drivetrain deliver power with less loss through movement at the mounting point. This upgrade suits workshop tuning, replacement during a rebuild, or a focused gearing change before the next run. Clear markings and included hardware keep the fitting process straightforward, while the stronger mounting point supports repeatable setup work across compatible TT-02 series chassis. Warning! Not suitable for children under 14 years.
RC tuning parts
TT-02/B/T/D Diff Lock Block, chassis accessory
300054649€19.99
The TT-02/B/T/D Diff Lock Block is a drivetrain tuning accessory for TT-02 chassis variant cars that converts the differential to a locked setup. Installed in the differential gear case in place of the kit-standard gears, it changes the way drive is delivered across the axle and supports a more direct traction response in specific running conditions. This conversion part is intended for situations where a standard differential is not the preferred setup. On extreme high-grip surfaces, the locked differential changes wheel action compared with the stock gear arrangement. The same hardware change can also be used when drifting, where a fixed differential setup is often part of chassis tuning. The part shown has a blue metal-look finish and is supplied with 4 silver screws for mounting. As a compact upgrade for TT-02 platform tuning, this accessory suits bench setup changes before track sessions or drift runs. It can be fitted when adjusting a car for a particular surface condition, then paired with the rest of the chassis setup to explore a different handling balance.
RC tuning parts
TT-02B Carbon FR Damper Stays RC Upgrade Set
300054754€60.99
The TT-02B Carbon FR Damper Stays set upgrades the front and rear shock mounting area of TT-02B chassis cars with 3 mm carbon fiber parts. Each stay replaces the standard FRP version with a more rigid structure, giving the suspension a firmer base where dampers and linkages attach during running and setup changes. The set includes 1 carbon front damper stay and 1 carbon rear damper stay, both shaped with multiple mounting points for the chassis layout. The carbon weave construction and 3 mm plate thickness focus this upgrade on stiffness rather than decoration, changing how load is carried through the damper towers under braking, acceleration and direction changes. The front and rear pieces are matched to the TT-02B platform, so the upgrade addresses both ends of the buggy instead of only one section. In tuning terms, a stiffer stay can make setup changes easier to read because the mounting area flexes less than the standard parts. On a workbench, the pair suits a focused chassis refresh or a targeted suspension update before the next run. Once installed on a TT-02B buggy, the carbon stays support damper mounting at the front and rear where repeated cornering loads and landing forces pass into the chassis structure. Warning! Not suitable for children under 14 years.
RC tuning parts
TT-02B DF-03 Aluminum Damper Set 2+2
300054993€87.99
This aluminum damper set equips a TT-02B or DF-03 chassis car with 4 oil-filled suspension units designed for controlled movement and a sharper response on the track. Slick-coated aluminum cylinders help the pistons move efficiently through the oil, supporting consistent shock absorption when the car lands, turns and changes direction. The set provides dedicated front and rear dampers, with 2 units for each end of the chassis rather than a one-size layout. Assembly documentation shows different piston setups for the 2 compatible chassis, including a 3-hole piston for TT-02B and a 2-hole piston for DF-03, plus a chassis-specific O-ring arrangement for DF-03. Silicone damper oil is included for filling the cylinders, and the build uses seals, rod guides, shaft guides, spacers and E-rings to complete each unit. The spring retainers can be rotated to adjust ground clearance on TT-02B, adding another tuning point alongside spring selection. Installed on a buggy chassis, the 4 dampers support more settled landings over jumps, steadier behavior through uneven sections and finer suspension setup work at the bench. For rebuilds, upgrades or fresh chassis builds, the grippy knurled caps and adjusters help keep small damper parts manageable during assembly and maintenance.
RC tuning parts
TT-02B Full Turnbuckle Set, RC tuning parts
300054539€23.79
The TT-02B Full Turnbuckle Set adds direct adjustability to key suspension and steering links on the TT-02B chassis. Metal turnbuckle shafts, rod ends and ball hardware work together so link length can be changed with the included wrench, making setup work more precise at the bench and easier to refine between runs. The set is arranged to build 7 adjustable links across the chassis. Instruction details show 3 x 23 mm shafts used for front upper arms and steering links, while 3 x 32 mm shafts are used for rear upper arms. Reference assembly lengths of 11.5 mm for the front upper arms and 16.5 mm for the rear upper arms are given in the manual, providing a clear starting point before fine tuning. The wrench is marked with 4 mm, 5 mm and 5.5 mm sizes, matching the small hardware used during installation and adjustment. Ball connectors, adjusters, flanged tubes, washers and screws complete the linkage hardware needed for the conversion. Once fitted, the turnbuckles can be rotated in place to make the links narrower or wider, a practical way to alter camber and steering geometry for different track conditions. That makes the set useful both during a fresh build and when revising handling after test laps. Batteries are not included.
RC tuning parts
TT-02B Rein Covers & L-Arms, chassis parts
300054815€9.99
The TT-02B Rein Covers & L-Arms set refreshes core suspension and drivetrain protection parts on TT-02B chassis cars with 2 matching sets of reinforced components. The parts tree combines lower suspension arms, gear covers, body mounts and battery posts in one chassis-focused pack, making it a practical choice when the original C sprue parts need replacement. The reinforced material is specified for improved chassis rigidity, a change that supports more stable response on high-grip carpet and asphalt surfaces. Front lower arms are supplied as C1 parts, rear lower arms as C9, body mounts as C6, gear covers as C7 and battery posts as C8. That spread of parts covers several heavily used mounting and running areas in one purchase, rather than replacing each section separately. Compatibility is stated for TT-02B chassis cars, and the set is intended for use with turnbuckle shafts. On a workshop bench, the grouped sprue format keeps related left and right chassis parts together during maintenance. For regular runners on carpet tracks or asphalt car parks, the reinforced arm and cover sections offer a straightforward way to restore worn areas with the correct TT-02B-specific parts.
RC tuning parts
TT-02BR Balldiff Gearbox Joints, RC spare parts
300022063€14.99
TT-02BR Balldiff Gearbox Joints are a focused RC spare parts set for maintenance on the TT-02BR platform. The pack centers on 2 molded joint pieces paired with 2 retaining rings and 2 metal pins, a combination suited to rebuilding a worn or incomplete balldiff gearbox connection with the correct matching hardware. The black joint components use a cylindrical upper section and a slotted lower end, a shape that indicates a guided mechanical fit where the pin locks the part in place and the retaining ring secures the assembly. That layout matters during service work because small drivetrain parts need the right companion pieces to go back together cleanly. Instead of mixing general workshop hardware, this set keeps the parts grouped for the specific TT-02BR balldiff area. The compact format also makes it practical to keep as a bench spare for routine rebuilds. Used during repair or scheduled maintenance, the set supports a direct refresh of the gearbox joint area when wear, loss or disassembly interrupts a running chassis. On a hobby bench, the separated parts are easy to identify before installation, and the matched count of joints, rings and pins helps keep the rebuild process organized.
RC tuning parts
TT-02S Alu. Steering Set LT, RC steering upgrade
300054965€69.99
The TT-02S Alu. Steering Set LT is an RC steering upgrade for TT-02 Type-S chassis cars, built around an aluminum steering bridge with a long tie-rod design for smoother cornering and a more intuitive driving feel. Aluminum steering arms for the left and right sides, aluminum steering posts and reinforced adjusters bring the steering assembly together as a focused chassis tuning set. The set uses 3 turnbuckle shafts in 2 lengths, with 2 pieces at 3x38 mm and 1 piece at 3x42 mm, allowing the linkage to be set up to the required geometry. Open face reinforced adjusters support fine adjustment, while the long tie-rod layout helps the steering move with a clean, controlled action through corners. The image and parts layout show a hardware-based upgrade with machined metal parts, threaded links, rod ends, washers and mounting hardware arranged for a complete steering conversion. New steering post attachment positions contribute to greater reliability in the steering area during repeated running sessions. On the bench, this set suits drivers refining the response of a TT-02 Type-S chassis car with a more precise linkage layout than the standard steering assembly. Once fitted, the aluminum parts and adjustable turnbuckles support careful setup work for track sessions where steering feel and corner entry matter.
RC tuning parts
TT-02S Steel Suspension Mount Set F/R for Chassis
300054634€53.99
The TT-02S Steel Suspension Mount Set F/R adds a focused chassis upgrade to the TT-02 Type-S platform with steel front and rear suspension plates and matching hardware for both ends of the car. The revised plate design opens up rebound stopper compatibility, giving the suspension layout more room for detailed setup changes during track preparation. Alongside the front and rear plates, the set contains 4 gearbox joints plus front and rear suspension shaft adapters, with spacers and flanged pipes supplied to complete the installation hardware. One black plate is marked 3.0, and the rear mount is designed to give 3 degrees of toe-in, a geometry choice that helps the chassis settle more cleanly in higher-speed sections. The parts are intended for TT-02 Type-S chassis use. Suspension arms and uprights are not included. For standard TT-02 chassis use, separately sold damper stays are required at the front and rear, along with oil dampers. This makes the set a strong choice for builders refining a current TT-02 Type-S machine or planning a more exact suspension layout around optional rebound stoppers and chassis-specific hardware.
RC tuning parts
TTFR Sh. Damper Spring Hard (2), RC spring set
300053632€7.79
The TTFR Sh. Damper Spring Hard (2) is a suspension tuning set with 2 blue metal coil springs for RC chassis setups that use the TRF damper set 53571. Its shorter free length, about 5 mm below the hard spring from OP440 street spec, lowers vehicle height and supports a more settled attitude when pace rises on faster sections. This spring set is intended for a wide spread of touring and front-wheel-drive chassis, including FF-03, FF-03 PRO, FF-04 EVO, M-07 Concept, TA05 Ver.II, TA06, TA06 PRO, TA06 MS, TA07 PRO, TA07 MS, TB-03, TB-03 VDS, TB-04, TB-04 PRO, TB-05 PRO, TT-01 Type-E, TT-01 Type-ES, TT-01D Type-E, TT-02, TT-02D, TT-02 Type-S and TT-02RR. In use, the firmer rate broadens suspension adjustment when combined with other springs, making it easier to tune ride height and chassis response for different surfaces and layouts. The 2-piece format suits left and right installation on the same end of the car. On indoor circuits, smooth asphalt layouts or club setups with longer straights, the lower stance can help keep the chassis composed through quick direction changes. As part of a suspension tuning box, these springs add another setup option for drivers refining balance, grip and response within a compatible damper package. Warning! Not suitable for children under 14 years.
RC tuning parts
Wheel Hub Clamp Type 6mm, RC wheel hub set
300053569€36.29
Wheel Hub Clamp Type 6mm brings a more secure wheel fixing method to compatible RC chassis by using a slotted hub that tightens with a cap screw on the axle. The machined aluminum construction adds precise shaping at this critical mounting point, where clean fit and firm clamping matter every time the wheel is installed. A key detail of this design is the captured 2 x 10 mm stainless steel shaft. When the wheel comes off, the shaft does not drop away as easily, which helps keep maintenance tidier and reduces interruptions at the bench. The set includes 4 wheel hubs, 5 cap screws and 5 stainless steel shafts, plus the hardware needed for the clamp system shown in the supplied parts. This accessory is intended for a broad range of compatible chassis, including TD4, TD2, CR-01, DF-03, DF-02, DT-03, DT-03T, DT-02, FF-03, FF-04 EVO, MF-01X, TA06, TA07, TA08 PRO, TB-03, TB-04 PRO, TB-05 PRO, TC-01, TRF420, TRF419, TT-02, TT-02B, TT-02D, TT-02RR, TT-01 TYPE-E, WR-02C and XV-02PRO. It suits rebuilds, worn-part replacement and chassis updates where wheel retention and assembly accuracy at the axle are a priority. During routine wheel removal, the clamp layout helps keep the hub and shaft arrangement together, which supports faster service between running sessions. Warning! Not suitable for children under 14 years.
RC tuning parts
XV-01 Alu. Sus. Mount XJ, chassis mount
300054379€21.29
The XV-01 Alu. Sus. Mount XJ is a chassis upgrade part for compatible XV series platforms, combining a machined aluminum build with a blue anodized finish and a direct fit for the suspension mount area. On XV-02PRO, XV-01, XV-01 PRO and XV-01T chassis, it replaces the kit-standard part with a more rigid mount section that is tuned for hard off-road driving. That added rigidity matters at the point where suspension loads transfer into the chassis. By firming up the mount section, the holder allows smoother suspension movement when the car is driven over loose ground, ruts and uneven sections. The U-shaped form and threaded mounting points are made for precise installation in the relevant chassis area, and the anodized surface gives the part a crisp workshop look alongside the rest of a tuned running setup. Scope of delivery contains 1 control arm holder. This part suits maintenance work, targeted tuning and rebuilds where the suspension mount section is being refreshed with a metal replacement. It fits naturally into off-road running setups that place repeated stress on the chassis and call for accurate movement through the suspension travel. Warning! Not suitable for children under 14 years.
RC tuning parts
XV-01 F Parts, suspension arms for RC chassis
300054444€11.69
These carbon reinforced F Parts are designed for the XV-01 chassis and replace the kit-standard front and rear suspension arms with a stiffer setup. The added rigidity supports a more consistent suspension geometry on tarmac surfaces, where steering input and cornering balance depend on precise arm movement and stable mounting points. The molded parts use a ribbed arm structure with circular mounting holes and integrated linkage posts, giving the suspension layout the exact connection points needed for installation on the XV-01 platform. As chassis tuning parts, they focus on a specific mechanical area rather than changing the whole car, making them a targeted upgrade for drivers refining handling response. The front and rear arm format keeps the suspension layout matched across both ends of the chassis. Carbon reinforcement adds stiffness to the component itself, which is the key change from the standard version named in the data. In workshop use, these parts fit naturally into routine maintenance after wear, damage or a handling-focused rebuild of an XV-01 runner. On sealed surfaces, the stiffer arm setup supports cleaner corner entry and a more settled line through bends when the chassis is driven on tarmac.
RC tuning parts
XV-01 Sep. Sus. Mounts 1XJ, suspension mounts
300054376€28.99
The XV-01 Sep. Sus. Mounts 1XJ are an aluminum chassis upgrade for the suspension mount area on XV-01 series vehicles, bringing a more rigid foundation to a section that works constantly over uneven ground. The blue-anodized finish and machined form give the pair a clean technical look while fitting directly into the layout used by compatible chassis. This set is intended for the XV-01 chassis, XV-01 PRO chassis and XV-01T chassis. By replacing the standard resin parts with aluminum mounts, the suspension mount section gains greater rigidity, which supports smoother suspension movement during hard off-road driving. The scope of delivery includes 2 control arm holders, covering this specific upgrade point as a matched pair rather than a mixed assortment of hardware. The engraved 1XJ marking identifies the mount specification used for this part. On rally-style runs over loose dirt, rough tracks or broken surfaces, the stiffer mount section helps the suspension work with a more consistent response under load. As a focused tuning part for compatible XV-01 platforms, these mounts suit builders refining chassis behavior through material changes at key mounting points. Warning! Not suitable for children under 14 years.
RC tuning parts
XV-01 Sep. Sus. Mounts 1XM, suspension mounts
300054377€28.99
The XV-01 Sep. Sus. Mounts 1XM bring a focused chassis upgrade to the suspension mount area on XV-01 series models. Made from aluminum and finished with a blue anodized surface, these mounts replace the standard kit parts with a stiffer mounting point that supports smoother suspension movement when the chassis is driven hard off road. The upgrade is specified for XV-01 chassis, XV-01 PRO chassis and XV-01T chassis, so fitment stays tied to the platform named in the data rather than a broad universal claim. The separate suspension mount design concentrates on the section that locates the control arms, where rigidity influences how freely the suspension can move under load. The machined metal construction and anodized finish also make the parts easy to identify during a rebuild or tuning session. Scope of delivery: 2 control arm holders. On loose dirt, rutted tracks and uneven mixed surfaces, suspension response depends on how accurately the mount section holds its position as the arms cycle through travel. This upgrade suits maintenance, repair and performance tuning on compatible XV-01 models, especially where repeated off-road use calls for a more rigid suspension mounting setup. Warning! Not suitable for children under 14 years.
RC tuning parts
XV-01 Slipper Clutch Set, RC chassis accessory
300054378€61.49
The XV-01 Slipper Clutch Set adds a dedicated tuning function to compatible XV-01 based chassis by introducing a clutch unit that can slip under load instead of passing every shock directly into the transmission. On loose rally-style running, that controlled response helps the chassis stay composed when throttle inputs, braking zones and uneven landings place sudden stress on the driveline. This set is designed specifically for the XV-01 chassis and also works with the XV-01 PRO chassis and XV-01T chassis. For XV-01 and XV-01 PRO, it is used in combination with 54382, 54383, 54466, 54467 and 54468. For XV-01T, it is used with 54382. The scope of delivery contains 1 slipper clutch set with 11 pieces, built around the clutch hardware needed for this upgrade. Installed on a compatible chassis, the unit gives builders a practical way to tune power delivery for changing surface conditions, especially where low grip makes abrupt drivetrain transfer harder to manage. It suits workshop upgrades focused on transmission protection, traction tuning and more controlled running across acceleration zones, braking points and rough landings. Warning! Not suitable for children under 14 years.
RC tuning parts
XV-01/T Front/Rear Stabilizer Set, RC chassis tuning
300054514€24.99
The XV-01/T Front/Rear Stabilizer Set adds a focused suspension tuning option to the Tamiya XV-01 cross platform chassis, using front and rear sway bars to alter how the car responds through corners and direction changes. Instead of changing major drivetrain parts, this set works through roll stiffness, making it a practical way to refine balance on rally-style running surfaces. The set supplies 3 stabilizer wire diameters, 1.1 mm, 1.2 mm and 1.3 mm, with 2 of each included for setup changes at both ends of the chassis. Blue stabilizer ends connect the bars to the suspension hardware, while 5 mm adjusters, 4 mm adjusters, grub screws and mounting screws support the linkage assembly. The instruction material shows front and rear linkages built to 25.5 mm, with adjusters trimmed and secured by screws before installation on the suspension arms. This gives the set a clear mechanical role: the bars twist as the suspension loads up, influencing chassis roll with a setup that can be changed to suit conditions. Compatibility is specified for the XV-01 and XV-01T chassis. XV-01 TC chassis models are not supported. On a loose track, a milder bar can keep the response more progressive, while a firmer choice can sharpen the car on higher-grip sections and help dial in front-to-rear balance during testing sessions.
RC tuning parts
XV-02 37mm Drive Shafts, RC spare part pair
300022054€20.79
These 37 mm drive shafts are a dedicated drivetrain upgrade for XV-02 chassis cars and bring the Double Cardan layout into the driveline with a matched pair of shafts. Each shaft carries 2 joints, a configuration described for ground-hugging drive, which helps the chassis keep drive transfer connected through changing suspension angles. The 37 marking on each shaft identifies the specified length at a glance during setup or maintenance. The set contains 2 drive shafts and matches the size of the 37 mm universal drive shaft, making it a focused choice when a build calls for this exact format. As part of the Hop-Up Option Series, these shafts suit replacement work, driveline servicing and chassis-specific tuning on compatible XV-02 cars. The listed companion parts are axle shafts, joint casings, cross joints and 1050 ball bearings, which shows the intended Double Cardan component system around the shafts. On the bench, the pair supports precise rebuilds where matching left and right driveline parts matter. In running sessions on an XV-02 chassis, the Double Cardan joint structure is aimed at keeping drive planted as the car moves across uneven sections and changing grip levels.
RC tuning parts
XV-02 Alu. Damper Stay Mount, RC chassis part
300022056€30.99
The XV-02 Alu. Damper Stay Mount is a dedicated RC chassis part for XV-02 cars, made to support the damper stay area with a precisely machined aluminum component. Supplied as 1 mount, it fits either the front or rear position, which gives the same part a clear role in repair work or targeted chassis tuning. Its metal construction brings a firm mounting base where the damper stay is fastened, and the shaped profile uses multiple mounting points to align with the XV-02 layout. The compact form keeps the part focused on structural support rather than adding unnecessary bulk. As a replacement component, it suits worn or damaged assemblies; as a tuning part, it gives builders a defined way to revise suspension mounting hardware with a material change from the standard setup. On the workbench, the mount fits naturally into rebuilds, maintenance sessions and setup revisions on XV-02 cars. Front or rear use also makes it practical to keep on hand when preparing a chassis for regular running, part replacement or incremental handling changes. Warning! Not suitable for children under 14 years.
RC tuning parts
XV-02 Alu. Steering Arms L/R, RC chassis parts
300022072€39.99
The XV-02 Alu. Steering Arms L/R bring machined aluminum construction to a key steering area on XV-02 chassis cars. Each set contains a left and a right steering arm, both finished in Tamiya blue anodizing, with integrated ball bearings already built into the upper eyelets for smooth pivot action where the linkage changes direction. The metal construction gives these chassis parts a more technical feel than standard molded pieces, and the cutout shape keeps the design focused on the steering assembly rather than adding bulk. One arm uses a forked lower section with a threaded mounting point, while the matching counterpart uses a reinforced bracket form with 2 lower threaded holes, reflecting the different jobs each side handles within the front steering layout. That left and right specific design helps the pair sit correctly in the XV-02 geometry. On the bench, these parts suit repair work, a fresh chassis build, or a focused upgrade of the steering mechanism on an existing XV-02 car. During installation, the built-in bearings reduce the need for separate bearing handling at that pivot location, and the anodized finish makes the steering area easy to identify when the front end is apart for maintenance or tuning.
RC tuning parts
XV-02 Alum. Spur Gear Holder, chassis accessory
300022053€12.19
The XV-02 Alum. Spur Gear Holder is a chassis accessory developed for XV-02 cars and focused on one critical drivetrain area: the spur gear and center shaft. Its aluminium construction and firm hold around the spur gear support stable gear function, while the precise positioning of the center shaft helps the drivetrain transmit power with less loss through misalignment. As a Hop-Up Option, this part is aimed at builders who refine the running hardware of an existing XV-02 setup rather than changing the character of the whole chassis. The holder is supplied as 1 aluminium spur gear holder and is shaped for the matching XV-02 layout. In use, the part supports the spur gear at its mounting point, keeping the gear train located more exactly as the center shaft rotates through the drivetrain. That more exact placement matters where gear mesh and shaft alignment need to stay consistent across repeated running sessions. It fits naturally into service, replacement or tuning work on XV-02 chassis cars, whether a drivetrain is being refreshed after use or updated with selected aluminium upgrade parts. For bench installation, parts matching the XV-02 platform are required, and the holder is intended specifically for that chassis family. Warning! Not suitable for children under 14 years.
RC tuning parts
XV-02 Aluminum Adjustable Suspension Mount
300022055€20.79
The XV-02 Aluminum Adjustable Suspension Mount XH is a tuning part for compatible XV-01 and XV-02 chassis cars, built around an aluminum mount and matching bushing that support a firmer suspension attachment. The XH specification gives a defined mounting position for suspension setup work, with the same part usable at the front or rear of the chassis. The mount works with adjustable suspension mount bushings, which alter suspension shaft hole positions for more exact geometry changes than a fixed mount layout. In the XV-02 chassis, N3 is the standard bushing reference, while other bushing positions can be used to fine-tune settings. The instruction data also shows that different bushing offsets can affect toe angle, roll center and skid angle, adding more scope for detailed chassis tuning. Clearance can be adjusted with shims where needed during installation. The blue anodized finish and printed setup marks make the mount easy to identify among other chassis parts on the bench. This accessory suits builders refining an existing rally or on-road chassis setup, whether the goal is front-end response or rear-end stability. Used during rebuilds, maintenance or trackside setup changes, it adds a more adjustable suspension mounting point without changing the core chassis platform. Warning! Not suitable for children under 14 years.
RC tuning parts
XV-02 Carbon Bumper Support, RC chassis part
300022073€12.99
The XV-02 Carbon Bumper Support brings a focused chassis upgrade to XV-02 cars with a 2 mm carbon fiber plate and matching installation hardware. Its woven carbon pattern gives the front end a crisp racing look, while the shaped plate layout sits neatly around the bumper mounting area for a more technical finish on the completed model. Large outer mounting holes, smaller fixing points and the central cutout structure define how the part is arranged on the chassis. The set also includes 2 rubber bushes, 2 6 mm snap pins and 2 3 x 16 mm round socket screws, matching the specified mounting hardware for installation. The flat plate format keeps the component compact, and the carbon fiber construction makes it a natural choice for builders refining the appearance of an XV-02 machine with a dedicated option part. On a rally, road or mixed-surface XV-02 build, this support adds a visible upgrade at the front of the chassis where the carbon weave stands out immediately. It suits fresh builds as well as rebuilds that replace worn standard parts with a more distinctive carbon fiber alternative.
RC tuning parts
XV-02 Carbon Damper Stay R, RC chassis part
300022058€33.99
The XV-02 Carbon Damper Stay R is a rear chassis upgrade part for XV-02 cars that swaps the standard damper stay for a 3.5 mm carbon fiber plate. Its rigid construction gives the rear suspension a firmer mounting point, while the low material weight suits tuning work that focuses on response and setup precision around the damper area. The plate uses 5 rear damper attachment positions, giving more scope to alter mounting geometry than the standard stay. Precision-cut holes and slots support clean hardware placement, and the large center cutout reduces unnecessary material in the middle of the part. The set contains 1 rear carbon damper stay, 4 5 mm ball connectors, 4 3x10 mm hex head screws and 2 5.5x2.0 mm spacers. The included hardware matches the conversion shown in the supplied fitting information for the XV-02 platform. Installed at the rear of an XV-02 chassis car, this hop-up part suits bench tuning between runs or a more focused suspension setup before the next session. It adds a concrete adjustment point for builders comparing damper positions and refining how the rear end reacts on changing surfaces. Warning! Not suitable for children under 14 years.
RC tuning parts
XV-02 Gear Diff 06 Spur, RC spare gear, 70T
300022050€6.99
The XV-02 Gear Diff 06 Spur 70T is a dedicated RC spare gear for converting the kit-standard differential gear unit on the XV-02 to a center differential setup. By replacing the original ring gear with this 70-tooth spur gear, the drivetrain can distribute front and rear wheel speeds in a different way, which supports improved turning on the track and a more settled feel through direction changes. The black gear is built as a compact circular drivetrain component with fine outer teeth, a central bore and 4 evenly spaced mounting holes. Those details matter during installation because the gear must sit correctly within the differential assembly and mesh cleanly with the surrounding transmission parts. As a model-specific tuning component for the XV-02 platform, it is aimed at targeted setup changes rather than cosmetic modification. The 70T specification gives builders a clear reference when matching the part to the intended differential conversion. In workshop use, this spare gear suits maintenance, repair or planned drivetrain tuning on an existing XV-02 build. It fits naturally into bench sessions focused on cornering balance, transmission response and replacing worn internal gear parts with the correct designated component. Warning! Not suitable for children under 14 years.
RC tuning parts
XV-02 Setting Spring Set, chassis accessory, 40 mm
300022051€14.19
The XV-02 Setting Spring Set expands suspension tuning for XV-02 chassis cars with 3 distinct spring rates in one pack. Soft, medium and hard options make it possible to change how the chassis responds under load, giving a more deliberate route to setup work than relying on a single standard pair. With 6 springs in total, the set provides 2 pieces per rate for front or rear installation as required by the chosen setup. The springs measure 40 mm in length and are grouped by both rate and finish for quick identification during bench work. Black marks the soft pair, gold marks the medium pair, and silver marks the hard pair. The medium gold springs are the kit-standard specification, which gives a known baseline before moving to a softer or firmer setting. This makes back-to-back comparisons easier when adjusting the chassis for grip level, surface character or driving balance. On a workshop table, the set supports focused tuning sessions with clear hardware changes rather than guesswork. During maintenance or rebuilds on an XV-02 chassis car, the 3x2 format keeps the available rates together in one dedicated suspension option for repeatable setup changes.
RC tuning parts
XV-02 Slipper Clutch Set, RC chassis upgrade
300022048€69.99
The XV-02 Slipper Clutch Set is a Hop-Up Option for XV-02 chassis cars that adds a spring-loaded clutch unit between the drivetrain components to help absorb sudden surges. When load spikes travel through the transmission, the clutch can slip in a controlled way instead of passing the full shock straight through, which helps protect the drivetrain and supports steadier running where grip is limited. The set is built around the mechanical parts needed for this function, including pressure plates, a spur gear, spring, shaft, bearings, washers and retaining hardware. In use, the spring applies preload to the clutch assembly, while the friction surfaces and gear work together to moderate how force is transferred through the driveline. That makes this set relevant not only as a replacement assembly, but also as a tuning part for drivers refining how an XV-02 chassis responds under changing traction. On dusty pavement, loose surfaces or other low-grip conditions, the controlled slip can help the car settle more cleanly after abrupt power inputs. It also suits maintenance work on an existing XV-02 build where worn clutch or transmission parts need to be renewed with matching components for the same chassis platform.
RC tuning parts
XV-02 Universal Propeller Shaft RC Chassis Part
300022052€19.29
The XV-02 Universal Propeller Shaft is a drivetrain upgrade part for XV-02 chassis cars, replacing the kit dog-bone type propeller shaft with a universal shaft layout for steadier, more efficient power transfer. At the center of the set is a 66 mm aluminium swing shaft, joined to the input shaft through a cross joint that helps the drivetrain articulate smoothly while staying firmly connected. The set contains 1 aluminium swing shaft, 1 input shaft, 1 cross joint, 1 2x9.8 mm shaft and 1 3x2.5 mm grub screw. The instruction data also shows grease application points during installation and notes that the propeller shaft and input shaft use a firm joint that supports straightforward maintenance. A spacer is used for front installation, while rear installation does not require the spacer. Urethane bushings are referenced in the fitting guide, with the number depending on installation position and the center unit used. This chassis part suits builders refining the XV-02 drivetrain for running sessions where clean, consistent power delivery matters. It can be fitted at the front or rear, making it a focused upgrade when replacing the standard kit input shaft and propeller shaft in an existing XV-02 setup.
RC tuning parts
XV-02/TT-02 Ball Diff Set 39T, RC differential set
300022046€69.99
The XV-02/TT-02 Ball Diff Set 39T is a Hop-Up Option set for XV-02 and TT-02 chassis cars, built to change the rear drivetrain feel with a ball differential and 39T gear. Its limited slip differential effect supports steadier rear traction when the car loads up under power, helping the chassis settle more cleanly through changing grip conditions. The set is supplied as a full differential assembly package with gear parts, outdrives, diff housings, washers, bearings, pins, spring and adjustment hardware. In a ball differential, the internal balls run between the diff plates and gear components, while the screw and adjuster set the pressure that controls how freely the differential action works. That mechanism gives a tunable alternative to a fixed setup and allows the rear end to react with a different balance under throttle. The design also aims to keep grease from leaking, which helps maintain lubrication where the moving contact surfaces need it. On the bench, this set suits drivetrain tuning, maintenance work and rebuilds for compatible XV-02 and TT-02 cars. Once installed, it supports running sessions where cleaner power delivery and a more settled rear end matter, whether the chassis is being refreshed or tuned for a different track surface.
RC tuning parts
XV-02/TT-02 F Direct Coupling Set 39T
300022047€37.49
The XV-02/TT-02 F Direct Cpl 39T is a Hop-Up Option set for RC drivetrain tuning, built to give XV-02 and TT-02 chassis a more direct front drive feel on low-grip surfaces. By replacing front differential action with a direct coupling, this setup channels power to the front wheels in a more immediate way, which can sharpen launch response when traction is limited. The assembly shown in the set uses a 39-tooth gear together with outdrives, bearings, circlips, pins and screws, creating a dedicated front-end drivetrain unit rather than a general-purpose hardware pack. That focused layout makes it a targeted tuning change for drivers adjusting handling balance at the axle level. The effect under braking is equally important: with reduced differential effect at the front, the chassis can stay more composed as speed comes off and the car turns into a corner on dusty, loose or otherwise slippery tracks. This kind of tuning suits track sessions where surface grip changes through the day or where a standard differential setup gives away too much drive at corner exit. Installed in a compatible XV-02 or TT-02 chassis, the set supports a more locked-in front response for acceleration zones, braking points and repeated lap tuning on technical layouts.
RC tuning parts
XV-02/TT-02 Oil Gear Diff Unit, chassis accessory
300022049€37.49
The XV-02/TT-02 Oil Gear Diff Unit brings adjustable differential tuning to compatible RC chassis through an oil-filled gear design. Built for the XV-02 and TT-02 platforms, it uses the viscosity of the oil inside the differential case to alter how the internal gears transfer drive, giving a more deliberate way to refine handling than a fixed setup. The set shown includes the main differential housing, ring gear, internal bevel gears, cross shafts, outdrive cups, bearings, O-rings, gasket, shims, pins, screws and gear oil. Those parts support servicing, rebuilding or converting the drivetrain section with matching components in one package. On the XV-02 chassis, combining this unit with Item 22050, the 06 Module Spur Gear 70T for XV-02 Gear Differential, allows use as a center differential. That adds a specific configuration path for builders working on that chassis layout. This accessory suits tuning sessions, maintenance work and planned drivetrain changes on compatible RC cars. It fits naturally into bench work where differential action, sealing parts and rotating hardware are being refreshed together, and it gives repeatable setup scope through oil choice rather than through a full hardware swap each time.
RC tuning parts
XV-02/TT02 Axle & Ring Set, RC spare parts
300054623€14.79
The XV-02/TT02 Axle & Ring set updates the wheel end of a universal shaft assembly with 2 wheel axles and 2 axle rings. This layout is designed to deliver smoother rotation with less power loss, helping the drivetrain run with a cleaner, more direct feel when the car is in motion. Instead of the earlier axle shaft style that used a set screw to hold the pin in place, this version uses an axle ring arrangement that addresses potential looseness in that area. The parts fit to the swing shaft in an existing universal shaft set, so the upgrade targets the working section of the drivetrain rather than replacing the full assembly. The instruction data also notes that axle ring orientation differs between left and right, making correct installation direction part of the setup. The set can be used in place of the wheel axle in Items 53597, 53791 and 53792, and it also serves as a direct replacement for Item 53497 or 53681. On compatible M-Chassis, TT-02, DT-03 and DF-03 cars fitted with universal shafts, this set suits routine maintenance, worn-part replacement or a focused drivetrain refresh. It is a compact hardware upgrade for builders who want to refine rotation at the axle end while keeping the existing universal shaft system in service. Warning! Not suitable for children under 14 years.
RC tuning parts
XV-02RS Stabilizer Set, chassis accessory, front rear
300022074€23.19
The XV-02RS Stabilizer Set Fr./Re. adds a front and rear anti-roll setup to the XV-02RS PRO Chassis, using 2 stabilizer bars and dedicated mounting parts to connect suspension movement across each axle. As the chassis leans in direction changes, the linked action of the bars helps moderate roll and supports a more settled handling feel on the track. The set contains 4 stabilizer rod stoppers, 4 stabilizer end 5 mm adjusters, 4 mm adjusters for 3 mm screws, 4 ball connectors in 5 x 10 mm size, and 8 grub screws. These parts work together as the connection points and adjustment hardware for the stabilizer mechanism, rather than as generic fasteners. The black rods and compact hardware layout suit the low, technical character of the XV-02RS PRO platform. Compatibility is stated for Item 58726, which keeps the fit tied to a specific chassis application. On a prepared RC car, this kind of tuning part is used when suspension balance needs a more exact mechanical response between left and right sides. It suits workshop setup sessions, chassis refinement between runs, and trackside changes where front and rear roll behavior needs to be matched to surface conditions. Warning! Not suitable for children under 14 years.
RC tuning parts
TRF Special Damper Set, RC chassis accessory
300042102€86.99
The TRF Special Damper Set brings a race-focused suspension upgrade to compatible on-road touring car chassis with 4 high-grade dampers for front and rear installation. Black fluorine-coated damper cylinders and titanium-coated piston rods work together to reduce friction and support smoother movement as the suspension cycles through corners, braking zones and direction changes. Each damper uses an oil-filled design with seals, O-rings and urethane bushings arranged to control movement inside the cylinder. The set includes 2-hole and 3-hole pistons, allowing the damping setup to be matched to different chassis needs, while the cylinder nut adjusts spring tension by rotation. Damper oil is not included in the set. Blue damper caps, O-ring caps and spring retainers add a distinctive technical finish, and the included white medium springs complete the 4-piece layout. This chassis accessory suits tuning sessions, rebuilds and suspension refreshes on compatible RC touring cars. It fits most on-road touring car chassis, with listed examples including TT-01, TA05, TB-02, TB-Evo.V and TRF415, making it a useful choice when a build calls for lower-friction damper action and adjustable spring preload. Warning! Not suitable for children under 14 years.
RC tuning parts
0.6 Alu Pinion Gear 16T, RC drivetrain gear
300054464soon available again
This 0.6 module aluminum pinion gear with 16 teeth is built for RC drivetrain setups that need precise meshing and a clean mechanical response. The hard coated finish works with the aluminum construction to support repeated use, while the compact 16T format suits gearing changes where tooth count directly shapes how the drivetrain responds on the track or bench. A special tooth shape sets this gear apart from a standard cut pinion. As the teeth engage, the profile is designed to reduce friction loss in the mesh, which helps power move through the transmission with less wasted motion. The same tooth design also reduces gear noise, giving the drivetrain a more controlled sound during running checks and setup work. For tuning sessions, a pinion like this can be a small but meaningful change, because module, tooth count and tooth form all affect how the motor and spur gear work together. The gear suits builders maintaining an existing RC model, replacing a worn drivetrain part, or adjusting gearing for a different running setup. It also fits neatly into a spares box for workshop use, where a specific 16T pinion can be the exact part needed to complete a fresh transmission combination.
RC tuning parts
42mm TRF/TT-02 Swing Shaft, RC spare part
300042356soon available again
The TRF/TT-02 42mm Swing Shaft (Hard) is a drivetrain upgrade part for RC chassis builds that need efficient power transfer through an assembly type universal shaft. Each pack contains 2 silver metal shafts marked A 42, with a reinforced construction and a hard anodized finish that supports repeated use in running setups where the driveline is under regular load. A key detail lies in the shaft geometry: the drive pin and cross shaft are positioned 90 degrees apart, a layout that promotes smoother rotation when power is applied. That mechanical relationship helps the universal shaft work with less interruption through the turn of the drivetrain, which is especially useful when a chassis is set up with stronger power systems. The different thickness compared with standard counterparts gives these parts a more reinforced specification for replacement, maintenance, or tuning work. The 42 mm size is intended for direct use with TT-02 Type-S and TB Evo.6 chassis cars, making the pair a focused option for keeping those platforms running cleanly. In workshop use, the shafts suit routine rebuilds, worn-part replacement, or a driveline refresh before the next session on track. The 2-piece pack also provides the matching pair needed for balanced installation within the compatible universal shaft setup.
RC tuning parts
Adjustable Suspension Mount E, aluminum RC part
300054882soon available again
The Adjustable Suspension Mount E is a focused RC tuning part for chassis setup changes that go beyond a fixed suspension block. Its aluminum construction replaces the standard suspension mount and works with interchangeable bushings to alter toe angle, tread, roll center and skid angle in one compact assembly. The blue anodized finish gives the part the familiar Tamiya appearance while keeping the function clearly visible during setup work. The included bushing sprue carries 7 pairs of bushing types, each with a different suspension shaft hole position. Together they create 25 potential shaft offset positions, so small geometry changes can be made by selecting and rotating the inserts rather than changing the whole mount. This E mount allows settings between C and G, and the final toe angle depends on the separate suspension mounts and bushings used alongside it. The instruction data also notes that shims can be used as needed to adjust clearance during installation. On the bench, this part suits repeatable tuning sessions where a chassis is adjusted step by step for different track layouts and handling goals. It is compatible with TRF419, TA07 and TB-05 chassis cars, making it a direct upgrade path for drivers refining suspension response within those platforms.
RC tuning parts
Alu.Servo Stay (R) TB-03, chassis accessory
300054090soon available again
The Alu.Servo Stay (R) TB-03 is a chassis accessory built to give the servo mounting area a stronger aluminum support while also reducing the contact area with the chassis. That combination targets two concrete effects in one compact part: firmer servo retention and improved roll characteristics during running. The set contains 1 right-side aluminum servo stay and 7 parts in total for installation. The blue stay is paired with mounting hardware shown as screws and washers, forming a dedicated fastening set rather than a generic bracket alone. Its right-side layout is specific to the stated application, which matters when tuning or replacing steering-related chassis hardware. For the FF-04 EVO chassis, this stay is used instead of NN29. For the TA05 ver.II chassis, there is one stated fitment limit: part 54096 cannot be used together. This kind of upgrade suits rebuilds, maintenance work and chassis-specific setup changes where the servo mount needs a defined replacement part rather than a universal solution. On the bench, the aluminum construction and model-specific fitment help keep a compatible drivetrain or steering build on the intended parts path. Warning! Not suitable for children under 14 years.
RC tuning parts
Buggy Champ Ball Diff Set II, RC option part
300054897soon available again
The Buggy Champ Ball Diff Set II brings a classic drivetrain upgrade back into the regular Hop-Up Option parts series and gives compatible buggy re-issues a more efficient, more controllable way to deliver power. Built around a ball differential mechanism, the set supports finer tuning than a fixed differential feel and suits running sessions where traction changes across dirt, gravel, or mixed surfaces. This re-issue follows the previously limited edition release 84113 and makes the same upgrade available again as a standard option part. The included hardware covers key internal components for the assembly, with a 1150 ball bearing, 8 differential balls in 3 mm size, and 4 mm and 5 mm screws listed in the set contents. Differential adjustment can be carried out while the unit remains installed in the gearbox, which simplifies service access during routine tuning and lets setup changes happen with less disassembly. Compatibility is stated for Item 58441 Buggy Champ 2009, Item 58452 Sand Scorcher 2010, and Item 47304 Fighting Buggy 2014. For restoration projects, period-style buggy builds, or regular track use, this option part adds a concrete tuning step to the drivetrain rather than a cosmetic change. It fits naturally into workshop sessions focused on traction balance, throttle response, and maintaining classic rear-drive buggy platforms with period-correct upgrade parts. Warning! Not suitable for children under 14 years.
RC tuning parts
CC-02 Alum. Spur Gear Mount, chassis upgrade
300054970soon available again
The CC-02 Alum. Spur Gear Mount is a focused drivetrain upgrade for CC-02 chassis cars, replacing the kit-standard A5 part with an aluminum mount at the spur gear. That material change adds rigidity at a heavily loaded point in the transmission and supports more efficient power transfer, which the product data links to stronger acceleration. The mount fixes to the spur gear with 3 screws instead of the 2 used by the standard part, creating a more secure connection at the center hub. Included 5 x 7 x 0.3 mm shims are used to fine-tune the fit and reduce play in the assembly. The instruction data also shows the mount installed around a 2 x 10 mm shaft and secured with a 2 x 5 mm cap screw, with the completed gear assembly then fitted into the gearbox housing. A gun metal anodized finish gives the aluminum part a clean mechanical look that matches the technical character of the chassis. On a bench build, this upgrade suits drivers refining a CC-02 transmission with a more rigid spur gear mounting point. In running use, the tighter attachment and shim adjustment support a cleaner drivetrain setup for trail and off-road sessions.
RC tuning parts
CC-02 CarbSteel PropShaft 75mm, drivetrain part
300054998soon available again
The CC-02 CarbSteel PropShaft 75mm is a drivetrain upgrade part for CC-02S and CC-02M chassis cars, built to replace the standard P-parts propeller shaft with a more rigid carbon tool steel assembly. Its 75 mm format suits the specified chassis layout, and the telescopic structure allows the shaft length to change as suspension travel alters the distance between connected drivetrain points. That movement control is paired with a layout focused on efficient power delivery. The carbon tool steel material helps the shaft resist twisting when torque passes through the driveline, while the jointed construction with 2 propeller joints and 2 cross joints supports smooth rotation through changing angles. Propeller shafts A and B are included at 1 each to complete the assembly, and the matte black plated finish gives the installed part a clean mechanical look within exposed chassis areas. This set is intended for builders refining a CC-02 platform for more precise drivetrain action on running sessions where suspension movement is part of the chassis behavior. The box contains parts for 1 shaft assembly, so 2 sets are required to equip the full chassis where both shaft positions are being upgraded.
RC tuning parts
CC-02 Fr. Assy Univ. Shafts, RC chassis upgrade
300054984soon available again
The CC-02 Fr. Assy Univ. Shafts upgrade targets the front end of a CC-02 chassis car with a jointed drive layout built for efficient rotation and a more direct transfer of power. Carbon tool steel construction gives the shafts high rigidity, while the matte black plated finish adds a technical look that suits exposed axle and hub areas. This set uses Front Universal Shafts A and B together with 2 universal axles and 2 cross joints to replace the standard front drive parts. The universal-joint design changes how the front wheels receive drive as the steering moves, supporting smoother operation through the driven steering assembly. The included wheel axle parts are used in place of the kit wheel axles during upright attachment, as specified in the assembly information. A small amount of anti-wear grease is included for the moving joint areas, and threadlock is noted separately in the instructions for the grubscrews. On a trail-style CC-02 build, the upgrade focuses on the area that combines steering input and front-wheel drive, where cleaner joint movement can matter most. It also suits maintenance or rebuild work when the front axle assembly is being refreshed with more rigid drivetrain parts matched to the CC-02 platform.
RC tuning parts
DF-03Ra Heat Sink Bar Set, chassis option part
300053924soon available again
The DF-03Ra Heat Sink Bar Set adds a functional aluminum upgrade to the motor mounting area on compatible RC chassis. A blue anodized aluminum gear plate pairs with 3 heat-sink bars to increase heat dissipation around the motor section, while the ribbed bar shape expands the cooling surface in a compact layout. The set is designed for DF-03, FF-03 and FF-03 Pro chassis and installs at the motor plate area shown in the assembly diagram. The cooling effect can be adjusted by removing 1 or more of the bars, which allows different setups around the drivetrain space. The instruction diagram shows the bars mounted with 3 x 10 mm screws alongside the aluminum motor plate, with the motor shaft and pinion aligned into the gearbox. Gear clearance is adjusted so the gears turn smoothly after installation. Scope of delivery contains 1 heat sink set with 7 pieces. This option part suits rebuilds, tuning work and replacement projects where the motor area is being reworked on a compatible chassis. It also adds a distinct blue metal finish that stands out when the gearbox section is opened for maintenance or setup changes. Warning! Not suitable for children under 14 years.
RC tuning parts
DF-03Ra Slipper Set, RC chassis option part
300053925soon available again
The DF-03Ra Slipper Set adds an adjustable slipper clutch system to DF-03 chassis builds, pairing an 82T spur gear with clutch hardware that helps the drivetrain cope with the repeated shock of off-road running and jumping. Instead of a fixed connection alone, the assembly uses controlled slip at the spur gear to moderate sudden load changes through the transmission. The set works through a stack of pressure discs, slipper sheets, a slipper spring, spring retainer and 4 mm flange lock nut mounted around the spur gear. A 1 mm standard adjustment position is shown for the spring setting, and loosening the nut from that reference increases slipper action. The included 82T gear also opens further ratio choices when paired with compatible R/C 05 pinion gears in 23T, 25T, 26T or 27T sizes, as shown in the gearing chart for the DF-03 system. This option part suits maintenance, repair and tuning work on DF-03 based RC buggy setups where drivetrain response matters on loose ground and after landings. The 10-piece set keeps the main clutch components together for workshop installation, whether replacing worn parts or adding slipper control to a chassis that needs a broader tuning range. Warning! Not suitable for children under 14 years.
RC tuning parts
DT-02 Alu. Servo Mount, chassis accessory set
300054397soon available again
The DT-02 Alu. Servo Mount is a chassis accessory set for the DT-02 platform, built around aluminum parts that bring a clean, technical upgrade to the steering installation area. The compact L-shaped mounts and matching hardware suit maintenance benches, replacement work and fresh chassis builds where a dedicated servo fixing part is needed. The set contains 10 servo mount pieces, making it useful for keeping matching spares on hand across repeated rebuilds or service intervals. The included parts shown with the mounts support fastening during installation, while the metal construction gives the assembly a crisp, precise look inside the chassis layout. As a model accessory rather than a complete vehicle, this set focuses on one specific task: securing the servo mount position on the DT-02 chassis with parts made for that platform. On the workbench, the pack fits naturally into parts sorting, repair sessions and planned upgrades for an existing DT-02 setup. It also suits builders who keep replacement hardware ready between runs, so the next maintenance job can move straight to fitting and alignment with the correct mount parts close at hand. Warning! Not suitable for children under 14 years.
RC tuning parts
DT-02 Alum. Motor Heat Sink, RC motor cooler
300053831soon available again
The DT-02 Alum. Motor Heat Sink adds targeted cooling to RC motor setups with a blue anodized aluminum heat sink and matching motor plate. More and longer fins than ordinary heat sinks increase the surface area around the motor can, helping heat move away more effectively while the chassis is in use. A slit in the motor clamp opening allows air entry at the point where the heat sink grips the motor, supporting the cooling effect with a simple mechanical detail. The set includes 1 heat sink and 1 motor plate, and the instruction diagram shows the heat sink sliding onto the installed motor body after the motor is mounted in the gearbox. The blue anodized finish gives both parts a clean technical look while keeping the focus on thermal control for electric motor operation. Compatible with DT-02, DT-03 and DT-03T chassis, this upgrade suits rebuilds, maintenance work and performance-focused tuning sessions. It fits naturally into workshop setups where motor temperature management matters during repeated runs and longer driving periods.
RC tuning parts
DT-02 Turnbuckle Suspension Arm Tie-Rod Set
300053828soon available again
The DT-02 Turnbuckle Suspension Arm Tie-Rod Set brings adjustable suspension and steering links to the DT-02 chassis, replacing the standard upper arms and tie-rods with turnbuckle shafts that can be tuned directly on the car. Right and left-hand threads work through the central adjusters, so rod length changes with a simple rotation instead of removing the linkage each time camber or toe needs correction. The set contains 2 each of the 3x42 mm and 3x38 mm shafts, plus 1 each of the 3x65 mm and 3x85 mm shafts. A dedicated wrench is included for the turnbuckle sections, along with adjusters, ball connectors and the required mounting hardware. This layout supports use across the front and rear upper wishbones and the 2 track rods named in the supplied fitment notes. The opposite thread directions on the rods are part of the adjustment mechanism, allowing precise setup changes while the linkage stays assembled. On a DT-02 build or maintenance bench, this set supports more exact suspension and steering alignment before running sessions. It also suits routine setup changes when surface conditions or handling balance call for a quick camber or toe correction on the compatible chassis. Warning! Not suitable for children under 14 years.
RC tuning parts
DT-02/DT-03 Spring Set, RC damper tuning kit
300053832soon available again
This spring set expands the suspension setup range for DT-03, DT-03T and DT-02 chassis that run with CVA dampers. The pack contains 8 coil springs, with 2 soft and 2 hard springs for the front and the same combination for the rear, giving a direct way to tune the chassis for different road conditions. A key detail lies in the spring design itself: the softer springs use a longer free length, while the harder springs use a shorter free length. That difference keeps vehicle height unchanged when swapping between the two rates, so spring choice can focus on suspension response rather than ride-height correction. The set is intended for use with the DT-03 CVA oil damper set, the CVA oil damper set mini and the CVA oil damper set short, making it a focused upgrade for compatible buggy layouts. On loose ground, mixed surfaces or a familiar practice track, this set supports quick chassis experiments with front and rear balance. It suits builders who want to compare softer and firmer damping support on the same compatible platform and refine handling with a simple spring change. Warning! Not suitable for children under 14 years.
RC tuning parts
DT-03 Alum. Battery Bar, chassis accessory
300054564soon available again
The DT-03 Alum. Battery Bar is a dedicated chassis accessory for DT-03 models, built to hold the battery with a firm, rigid retainer. Its lightweight aluminum construction keeps the part focused on secure battery mounting while fitting the technical character of RC buggy maintenance and upgrade work. The bar uses a machined aluminum form with a blue anodized finish and is supplied with the small attachment parts needed for installation. This combination gives the chassis a clearly defined battery restraint that supports a neat internal layout around the battery bay. As a model supply rather than a complete vehicle, the part is intended for fitting into an existing DT-03 build where battery retention matters during repeated running sessions. The dedicated compatibility with DT-03 chassis models keeps selection straightforward for matching repairs or planned upgrades. On the workbench, the bar suits routine servicing, replacement of a worn retainer, or a fresh custom build based on the DT-03 platform. Once installed, it becomes part of the battery mounting setup inside the chassis, supporting a more secure hold where movement of the pack needs to be controlled by the fitted hardware.
RC tuning parts
DT-03 Alum. Steering Servo Mount, RC chassis part
300054565soon available again
The DT-03 Alum. Steering Servo Mount upgrades the steering servo installation on DT-03 and DT-03T chassis with a blue anodized aluminium mount that combines low weight and rigid support. Used in place of the standard M9 part, it gives the servo a firmer hold in the front chassis area, where steering input and component alignment work together through repeated running sessions. The mount is shaped for the steering servo assembly and is installed with the included small attachment parts. The instruction layout shows 3 x 10 mm screws, 3 mm washers and 3 x 1.5 mm spacers used during fitting, with a marked short and long side to guide the correct orientation of the mount. That directional fit matters because the servo mount sits directly within the steering section of the chassis, where placement affects how securely the servo is held. The aluminium construction replaces the standard molded part with a more rigid mounting point while keeping the setup focused on the DT-03 platform. On a buggy built around the DT-03 or DT-03T chassis, this chassis part suits maintenance, repair or a targeted steering-area upgrade. It fits naturally into rebuild work when the original M9 part is being replaced, and it also supports fresh assemblies that call for a more firmly mounted servo position.
RC tuning parts
DT-03 Rein M Part DS Mount, chassis spare parts
300054816soon available again
The DT-03 Rein M Part DS Mount brings a focused chassis update to DT-03 cars with carbon-fiber reinforced resin parts shaped for key structural positions. On the sprue are a damper stay mount, wing stay, front bumper parts and additional matching components that replace standard sections exposed to repeated load during running. The carbon-fiber reinforcement changes how these areas respond under stress, giving the chassis a firmer feel on high-grip carpet and asphalt where traction can place more force through the suspension mounts and bumper area. As a dedicated M parts sprue, this set suits repair work after wear as well as targeted tuning when a DT-03 setup needs more support in the front and rear mounting zones. The moulded layout also keeps each piece grouped for straightforward identification during parts selection. In workshop use, the set fits naturally into routine maintenance for a buggy that has seen frequent track sessions or repeated contact with barriers and jumps. It also serves as a practical upgrade path when preparing a DT-03 chassis for grippier indoor carpet or clean asphalt running, where a more rigid structure can help the car respond with greater consistency.
RC tuning parts
DT-03 Stabilizer Set Front/Rear RC Chassis Tuning
300054561soon available again
The DT-03 Stabilizer Set front/rear adds a focused suspension tuning option to DT-03 and DT-03T chassis cars by fitting sway bars at both ends of the car. Once installed, the bars reduce chassis roll and help the car carry a more even balance through changing off-road track conditions, whether the surface is loose, grippy or uneven. The set provides 2 stiffness choices for the front and 2 for the rear, with soft red rods and hard blue rods for setup changes. That gives room to adjust how strongly each end resists roll instead of locking the chassis into a single response. The included parts go beyond the bars themselves, with stabilizer ends, 5 mm ball connectors, screws, grub screws and a 1.5 mm hex wrench supplied for assembly. The manual notes front rods in 1.4 and 1.6, and rear rods in 1.4 and 1.8, adding another concrete reference for setup selection across the front and rear suspension. On a prepared dirt track, a looser surface or a layout with repeated direction changes, this tuning range helps tailor the car to the conditions rather than leaving the suspension in one fixed state. For drivers refining a DT-03 buggy or DT-03T truck, the set adds a direct way to adjust roll behavior through hardware mounted on the chassis itself.
RC tuning parts
F104 Alu Clamp Type Wheel Stopper, chassis part
300054240soon available again
The F104 Alu Clamp Type Wheel Stopper is a chassis part for all F104 chassis, built around a clamp mechanism that secures the shaft by tightening the slot in the stopper with a cap screw. That layout gives a controlled hold at the shaft while keeping adjustment work more precise during setup and servicing. A key detail of this design is its handling on carbon shafts. The stopper can be repositioned with subtle changes in placement without damaging the shaft surface, which matters when fine tuning drivetrain or wheel-related alignment on an F104 platform. The aluminium construction adds a crisp mechanical feel to repeated workshop use, and the clamp format avoids the more awkward handling that can come with installing and removing bearings in this area. On the bench, that means maintenance work around the shaft section can move forward with fewer interruptions when parts need to be checked, shifted or refitted. The included rim driver set with 4 pieces supports fitting and adjustment tasks, making this a focused upgrade part for keeping an F104 chassis easier to service and more exact to set up over repeated running sessions. Warning! Not suitable for children under 14 years.
RC tuning parts
F104 Alu. Diff Housing Set, RC chassis upgrade
300054158soon available again
The F104 Alu. Diff Housing Set brings blue anodized aluminum construction to the differential area of compatible Tamiya chassis, combining a cleaner mechanical feel with easier workshop handling. Once installed on an F104-series machine, the housing stays together when the wheels come off, so routine checks and maintenance take less disassembly around the rear drivetrain. The set is supplied as a 13-piece differential parts set and covers the core hardware needed for this upgrade section. Visible components include diff housings, a 2 x 14 mm shaft, an 1150 ball bearing, a differential spacer, a 4 mm lock nut, 3 x 3 mm grub screws, disk springs, washers and a 1.5 mm hex wrench. The assembly sequence uses the grub screw to align with the shaft recess, while the lock nut is adjusted to set the differential position. Manual notes also show grease application and a quarter-turn backing-off point after fully tightening the lock nut as the standard adjustment position. Compatibility is stated for F104PRO II chassis, F104W chassis and F104 chassis. The set can also be used on the F103 chassis when item 54162 is added, because a shorter axle is required there. This makes the set a focused upgrade for racers who tune drivetrain response, service the rear axle regularly, or want a more refined differential housing than the standard setup. Warning! Not suitable for children under 14 years.
RC tuning parts
FF-03 Pinion Gear 26/27T, RC spare part, M0.6
300054228soon available again
The FF-03 Pinion Gear 26/27T M0.6 set adds a focused drivetrain upgrade for compatible RC chassis, combining 2 aluminum motor pinions with a fluorine lubricating coating and a newly developed tooth tip shape. Rounded teeth help the gears mesh more smoothly, which can reduce friction losses and running noise while supporting cleaner power delivery through the transmission. The set provides 26T and 27T options in one pack, making it useful for gearing changes between different track layouts or maintenance sessions. In the box are 2 pinion gears, 3 set screws and an L-shaped hex wrench for fitting and adjustment. The M0.6 gear pitch matches the stated applications, and the parts are intended for use on a broad range of chassis including FF-04 EVO, FF-03, FF-03 PRO, TA08 PRO, TA07 PRO, TA06 PRO, TB-Evo.7, TB-Evo.6, TC-01, TT-02, TT-02D, TT-02RR, XV-02PRO and XV-01 PRO. For TA07 MS chassis, use with 51356, 51423 and 51548. For TT-02, TT-02D and TT-02RR chassis, use with 54500. This makes the set a practical choice for tuning, servicing or replacing drivetrain parts where the correct matching components are already in place. Warning! Not suitable for children under 14 years.
RC tuning parts
H.T. Servo Saver Alum. Horn, RC steering part
300054121soon available again
The H.T. Servo Saver Alum. Horn anodized is an RC steering upgrade part that replaces the Q5 part in the high torque servo saver. Its aluminum construction increases rigidity in the steering section, which the product data states creates a more direct steering feel. The blue anodized finish adds a distinct visual accent at the steering assembly while keeping the focus on a functional replacement part. This part is intended for a wide range of Tamiya chassis families named in the data, including XV-01, XV-01T, XV-01 PRO, TA06, TA06 PRO, TA06 MS, FF-03, FF-03 PRO, TB-03, TB-04, TB-04 PRO, TA05 ver.II, M-05, M-05 PRO, M-05 ver.II PRO, DF-03, GF-01, GF-01TR, GF-01CB, G6-01, G6-01TR and CC-01. For G6-01, G6-01TR and CC-01 chassis, use is stated in combination with 51000 or 50473. The scope of delivery contains 1 servo arm. In workshop use, the horn suits rebuilds, steering refreshes and chassis-specific tuning where a firmer connection at the servo saver is required. It also fits display-oriented builds that benefit from the blue anodized detail around the steering hardware. Warning! Not suitable for children under 14 years.
RC tuning parts
M-05 Alu Racing Steering Post RC Chassis Upgrade
300054193soon available again
The M-05 Alu Racing Steering Post is a steering upgrade part for selected Tamiya M-chassis platforms, replacing the standard B3 parts with machined aluminum components. The rigid construction focuses on the steering column area, where cleaner support can help the mechanism react with a more direct feel during corner entry and direction changes. Compatibility is stated for the M-06 PRO chassis, M-05 ver.II PRO chassis, M-05 chassis and M-05 PRO chassis. The set is not included in the M-05 PRO as a standard part, making it a relevant hop-up for builds based on the regular chassis specification. The instruction sheet also specifies replacing the steering arm's /850 plastic bearings with ball bearings when fitting this part. Shaded components shown in the diagram are not included in the set, so the upgrade stays focused on the steering post area rather than a full steering assembly. In workshop use, this kind of aluminum steering hardware suits drivers refining response on compact front-wheel-drive RC chassis and builders maintaining an existing M-series setup. The 10-piece steering arm post pack also supports spare-part planning when servicing steering components between running sessions or during a fresh chassis rebuild. Warning! Not suitable for children under 14 years.
RC tuning parts
M-05 Alu.Turnbuckle Steer Rod, RC linkage set
300054195soon available again
The M-05 Alu.Turnbuckle Steer Rod is an RC linkage set for specified M chassis platforms, built to replace the standard 3 x 89 mm twin screw shaft with an adjustable aluminum alternative. Its blue anodized finish and square center section give the rod a clean technical look while supporting subtle length changes directly on the car. Instead of removing the linkage for every correction, the center section can be turned to alter the rod length while the assembly remains fitted. That makes steering setup work more direct when small alignment changes are needed between runs or during bench maintenance. The set contains 4 pieces and is intended for use with M-06 chassis, M-06 PRO chassis, M-05 ver.II PRO chassis, M-05 chassis and M-05 PRO chassis. The part is not included in the M-05 PRO. On a workshop table, this kind of adjustability helps keep setup changes controlled and repeatable when refining steering response on a compatible RC chassis. It also suits rebuilds that replace the stock shaft with a lighter aluminum linkage component while keeping the fit focused on the listed M series platforms. Warning! Not suitable for children under 14 years.
RC tuning parts
M-05 VII Carbon Rein. L Parts, suspension arms
300054614soon available again
The M-05 VII Carbon Rein. L Parts upgrade the suspension layout of Tamiya M-chassis cars with carbon fiber-reinforced nylon arms shaped for the M-05 Version II platform. Their higher rigidity compared with the standard glass fiber-reinforced parts helps the chassis react more directly on high-grip surfaces, giving steering inputs a crisper feel through corners and direction changes. This set is designed as a suspension arm replacement for the M-05 Ver.II PRO and can also be used on M-05 and M-06 chassis cars when parts modification is carried out. The arm design also supports rebound stroke adjustment through a screw on the arm itself when combined with Item 54605 M-05 Ver.II A Parts. Dampers must attach to the chassis via ball connectors, matching the mounting method shown for this setup. The instruction material also references left and right arm orientation, front and rear installation positions, and use in place of specific standard chassis parts during the conversion. On a tuned M-chassis build, this upgrade suits drivers refining steering feel for grippy indoor tracks or prepared asphalt layouts. It also fits workshop sessions focused on setup changes, where rebound tuning and arm rigidity are adjusted to match surface grip and chassis balance.
RC tuning parts
M-07C Alu Querlenkerhalter, chassis part, 4°
300054786soon available again
The M-07C Alu Querlenkerhalter vo./4° blau is a chassis tuning part for M-07 Concept cars that combines an aluminum build with a 4° front suspension setting. Mounted at the front suspension point, it changes the caster angle from the 5° of kit B1 parts to 4°, a setup stated to deliver more bite in turns on short and technical course tracks. The part comes as 1 aluminum front suspension mount with a blue anodized finish. Its machined metal construction is described as offering excellent rigidity compared with the standard resin part used in the kit, giving the front end a firmer mounting point. The visible 4° marking helps identify the setup during maintenance or rebuilds, and the mount is intended only for M-07 Concept chassis cars. As a dedicated chassis component rather than a general accessory, it targets handling adjustment through a specific geometry change at the front of the car. On compact layouts with frequent corner entries, this mount supports a setup focused on sharper turn-in bite. It suits bench tuning, replacement during a rebuild, or a planned change in front suspension geometry when preparing an M-07 Concept car for tighter circuits.
RC tuning parts
M-08 Concept Alum. St. Bridge RC Steering Upgrade
300054892soon available again
The M-08 Concept Alum. St. Bridge is a steering upgrade part for the M-08 Concept chassis, built to bring a more precise steering action and a firmer attachment point for linked components. Its blue anodized aluminum finish gives the part a clean technical look that matches the focused character of an RC chassis build. The set contains 1 aluminum steering bridge plus 5.5 x 2 mm spacers and 5.5 x 1.5 mm spacers, with 2 of each size supplied for clearance adjustment. The bridge works within the steering assembly and can also be attached in the opposite direction. Different spacer combinations can be used to alter steering Ackerman, giving a practical way to change how the front linkage responds through turns. The instruction material also shows a defined adjuster direction during fitting, which helps keep the steering geometry aligned as intended. Recommended for use with separately sold steering arms Item 54891. Installed on an M-08 Concept chassis, this part suits builders refining steering feel through hardware changes rather than broad setup guesses. It fits naturally into workshop sessions focused on front-end tuning, linkage alignment and repeatable handling adjustments between runs.
RC tuning parts
M-Chassis Aluminum Axle & Hub Set for RC Cars
300054996soon available again
This M-Chassis lightweight axle and hub set swaps the standard separate axle and wheel hub for a one-piece aluminum design, reducing the combined weight to half of the kit standard metal axle with a 5 mm hub. The lower rotating mass supports a more direct, clean wheel mounting setup on compatible RC chassis. Each set contains 2 one-piece aluminum axle and hub parts, plus spacers for tread adjustment. The aluminum parts have a hard anodized coating, adding a durable surface to these high-contact components. On M-07 and M-08 Concept chassis, spacer positions can be changed to match 4 mm, 5 mm or 6 mm hub values, while M-05 and M-06 chassis use the one-piece conversion in a 5 mm equivalent layout. The technical setup replaces the free wheel axle and uses the supplied hardware to secure the assembly in the upright. In workshop use, this set suits rebuilds, weight-focused tuning and worn axle replacement on M-Chassis cars. It also helps align wheel position with different body or track-width setups by changing spacer arrangement rather than changing separate hub sizes.
RC tuning parts
TA-06 Alum. Gear Diff Cover, RC chassis upgrade
300054602soon available again
The TA-06 Alum. Gear Diff Cover is a focused RC chassis upgrade for selected Tamiya platforms, built to replace the standard differential unit cover with an aluminum version that improves differential casing durability. Its blue anodized finish gives the part a crisp technical appearance while the machined form is designed for a clean fit in the gear differential area. This hop-up part is intended for TA06, TA06 PRO, TA06R, XV-01, FF-03R and TRF201XM chassis cars. The set contains the aluminum differential cover together with 4 countersunk screws and 2 bushings for installation. In the differential assembly, the cover helps secure the unit where repeated running loads act on the casing, making it a useful choice for high-specification chassis builds and maintenance work. The compact circular layout with raised center section follows the mounting pattern shown for the replacement step. It suits bench upgrades, rebuilds after wear, and planned tuning work on compatible chassis cars. During maintenance or a fresh setup, the part swaps into the differential area as a direct replacement component and adds a more hard-wearing metal element to this key section.
RC tuning parts
TA-07 Aluminum Steering Bridge RC Chassis Part
300054705soon available again
The TA-07 Aluminum Steering Bridge brings a focused steering upgrade to compatible RC chassis with a lightweight aluminum construction, a rigid layout and a blue anodized finish that stands out clearly on the bench and on the car. Developed around the proven TRF419 race machine design, this part is intended to replace the standard resin steering bridge on the TA07 PRO and sharpen front-end response during higher-speed running. Each set contains 1 aluminum steering bridge with 630 ball bearings pre-inserted, so the steering pivots are already prepared for installation. The machined shape combines low weight with a firm structure at the steering section, helping the chassis react more directly to input when pace rises. Compatibility covers TA07 PRO, TRF419 and TRF419X chassis, and the part is also recommended for use with the TA07 Aluminum Steering Arm Set for a matched steering setup. This upgrade suits rebuilds, race-day maintenance and targeted chassis tuning where steering feel matters as much as outright speed. Fitted in place of the standard part, the bridge supports a more connected response through quick transitions, sweepers and technical sections where precise line control makes a visible difference. Warning! Not suitable for children under 14 years.
RC tuning parts
TA08R Carbon Upper Deck, chassis option part
300022082soon available again
This TA08R carbon upper deck is a chassis option part for the TA08 PRO and TA08R, built around a 2.0 mm carbon fiber plate with a woven finish, multiple mounting holes and a central cutout. The shape and hole pattern make it a model-specific component for racers adjusting the upper structure of the chassis with a part designed for these platforms. The set contains 1 carbon upper deck, 1 630 ball bearing, 2 shims in 3 x 0.1 mm and 6 hex head screws in 3 x 6 mm. That combination supports installation with the matching small hardware instead of leaving the upper deck as a bare replacement plate. The carbon fiber construction keeps the part light while giving the chassis a distinctly technical look through the visible weave. The forked end geometry and larger circular opening show that this is not a generic panel, but a dedicated TA08-series tuning component shaped around the chassis layout. On a TA08 PRO build, the stated combination uses TA08 Aluminum Front Upper Arm Mounts, TA08 Aluminum Rear Upper Arm Mounts and the TA08R Aluminum Motor Mount. This makes the upper deck a clear choice for rebuilds, maintenance work and setup-focused bench sessions where model-specific compatibility matters as much as the part itself. Warning! Not suitable for children under 14 years.
RC tuning parts
TB-05 Alu. Diff Housing Set, chassis accessory
300042324soon available again
The TB-05 Alu. Diff Housing Set upgrades the differential section of compatible TB and TB Evo chassis cars with 2 aluminum 40T housing parts, replacing the standard resin components with a more rigid assembly. That higher rigidity supports smoother, more stable running, especially when the differential is shimmed precisely and the internal parts are seated cleanly inside the housing. The set contains Housing A, Housing B, 1 gasket and 8 screws in 2x5 mm size, concentrating the change on the differential case rather than the rest of the drivetrain. Aluminum also helps minimize heating of the internal oil during running, which supports steadier differential action as sessions continue. The housing shape is designed for the TB platform family named in the compatibility list, so the upgrade stays closely matched to the original chassis layout. As an option part, it suits builders who want to refine a running car with a more rigid differential case instead of changing the full chassis configuration. Compatibility covers TB-05 PRO, TB-04, TB Evo.7 and TB Evo.6 chassis cars. In workshop use, the set fits naturally into a rebuild, maintenance interval or performance-focused differential refresh where stable oil behavior and precise shimming matter.
RC tuning parts
TC Large Dia. Short Spring Set, damper tuning set
300042306soon available again
The TC Large Dia. Short Spring Set brings a focused suspension tuning option to RC setups that use super short big bore dampers. Inside the set are 6 black coil springs in 3 stiffnesses, with 2 soft, 2 medium and 2 hard springs that make back-to-back comparisons straightforward when a chassis needs a different response. Each spring has a free length of 20 mm, matching the compact format required by super short big bore damper layouts. The large-diameter design is made for the corresponding damper specification rather than general spring use, so the set stays targeted and easy to apply during setup work. Marking sleeves are included for the hard and soft pairs, with 2 yellow sleeves and 2 red sleeves that help separate spring rates quickly on the workbench. That clear visual coding reduces mix-ups when several damper sets or spare springs are laid out side by side. On carpet, asphalt or another prepared RC surface, changing from soft to medium or hard springs can help dial in how the suspension reacts to the track in front of the car. The set suits routine maintenance, race-day experimentation and repeatable setup testing where a small spring change can reshape the handling balance of a compatible chassis. Warning! Not suitable for children under 14 years.
RC tuning parts
TC-01 Carbon Battery Holders, chassis option part
300054986soon available again
These TC-01 Carbon Battery Holders bring a clean carbon fiber upgrade to the battery mounting area, replacing the kit-standard A11 parts with 3 mm components that combine low weight and firm support. One set weighs 3.6 g, giving this chassis section a lighter specification while keeping the structure focused on a precise fit. The release mechanism stays straightforward in use: removing a pin frees the battery pack, so access happens through a simple mechanical step rather than a more involved holder removal. The set contains 2 holders and is intended as an option part for compatible chassis cars. The instruction material also identifies use in place of A11 and shows installation on both sides of the chassis. For carbon edge protection, instant cement is available separately, and synthetic rubber cement may be used to retain the spacers during installation. On the bench, this option part suits rebuilds, maintenance intervals and detail-focused chassis updates where battery access and component weight both matter. It also fits multi-chassis collections that include TC-01, M-07 and M-08 cars, allowing the same holder format to be used across more than one platform.
RC tuning parts
TD4 Aluminum Rocker Arms, RC chassis upgrade
300022036soon available again
The TD4 Aluminum Rocker Arms set adds a focused suspension upgrade for TD4 chassis cars with 2 blue anodized aluminum parts and integrated ball bearings. Designed as left and right matching components, these rocker arms take the place of the kit-standard C5 parts and give the damper linkage a more exact, controlled feel during running. Each L-shaped arm uses a reinforced profile with a rounded outer corner and a bearing-supported pivot area, so movement through the suspension stroke stays clean and mechanically direct. The aluminum construction changes the character of this section compared with the standard resin part, while the anodized finish gives the pair the familiar Tamiya blue look. Because the set is dedicated to the TD4 platform, fit stays specific to that chassis layout rather than acting as a universal add-on. For tuning sessions, maintenance work or a step-by-step chassis build, this pair suits drivers who want to refine one section at a time. The set contains 2 rocker arms, one for each side, and 2 sets are required to fully kit out the chassis. That makes it suitable both for replacing a single axle pair and for planning a complete chassis conversion with matching hardware across the suspension system.
RC tuning parts
TD4 Rear Suspension Mount, RC chassis accessory
300022038soon available again
The TD4 aluminum rear suspension mount is a chassis accessory built for focused setup work on TD4 cars. Its aluminum construction and blue anodized finish give this rear mount a clean mechanical look while supporting a precise fit in the suspension area. The key function lies in its compatibility with separate resin bushings for suspension shafts. When those bushings are fitted, the mount allows detailed adjustment of toe, tread, roll center and skid angle settings, making it a useful choice for tuning chassis geometry around track conditions and handling preferences. The mount itself is dedicated to the rear suspension position, so changes can be directed at one specific area of the car rather than the whole chassis layout. The set shown consists of the blue mount and black insert parts for the mounting system. On a workbench, this kind of part suits planned setup changes between runs or a more exact rebuild of a TD4 rear end. It also fits neatly into a spares and upgrade collection for drivers who keep different geometry options ready for testing and maintenance.
RC tuning parts
TD4 Slipper Clutch Set, RC drivetrain parts
300022031soon available again
The TD4 Slipper Clutch Set focuses on a key section of the drivetrain, combining a 79-tooth spur gear, a 20-tooth pinion gear and the clutch hardware needed for this assembly. The layout is built around controlled friction between the clutch plates, so power passes through the gear train with a measured slip effect instead of a fixed, direct lock. The set also provides 2 friction discs, 2 octagonal plates, a compression spring, an O-ring, bushings, a shaft, a pin and a lock nut. Those parts work together as the clutch stack: the spring applies pressure, the discs create the friction surface, and the shaft and hardware hold the assembly in position. The marked tooth counts on the gears give a direct reference during setup and parts matching. The mix of gear, clutch and mounting components makes this set relevant for drivetrain service as well as for replacing worn clutch parts in an existing transmission. On the workbench, the separate parts make the mechanical sequence easy to follow during assembly and inspection. In running use, a slipper clutch of this type is used where controlled transfer through the drivetrain matters, especially when acceleration loads reach the gear stage quickly.
RC tuning parts
TD4 Stabilizer Set F/R, RC chassis tuning set
300022037soon available again
The TD4 Stabilizer Set F/R adds front and rear roll control to TD4 chassis cars, using 2 stabilizers to steady the car through corners and support a smoother, more composed handling feel on the track. The set is built around chassis tuning rather than cosmetic changes, so each part works directly on how the suspension reacts when the car loads up in a turn. Included are soft 1.1 mm and hard 1.3 mm stabilizer rods, with different shapes for the front and rear positions. That gives a direct way to alter how quickly the chassis transfers weight and how firmly each end resists roll. The aluminum hex head ball connectors allow minute left and right balance adjustments at the linkage, which helps when refining steering response or settling the car for changing grip conditions. The hardware layout shown for the set supports installation of the stabilizer system as a dedicated front and rear tuning upgrade. On a technical track layout with repeated direction changes, the set helps the chassis stay more consistent from one corner to the next. It also suits setup sessions where small suspension changes are tested back to back, with the 1.1 mm and 1.3 mm rod options giving 2 clearly different starting points for comparison.
RC tuning parts
TD4/TD2 Carbon Damper Stay Rear RC Part
300022061soon available again
The TD4/TD2 Carbon Damper Stay Rear brings a focused suspension upgrade to compatible TD4 and TD2 chassis cars, combining a carbon plate layout with a higher rear damper attachment for more tuning scope at the back of the car. With the mounting position set 2 mm higher than the standard arrangement, the stay supports effective use of optional dampers such as big bore dampers and gives the rear suspension a broader setup window. The set contains 1 rear carbon damper stay, 2 wing stays, 4 3x10 mm hex head screws, 2 3x8 mm countersunk hex head screws, 2 3x18 mm hex head screws, 2 mm aluminum spacers, 5 mm ball connectors and nylon lock nuts. The carbon construction keeps the main mounting section light while providing a firm base for the rear damper area. Multiple fastening points and the supplied hardware support a clean fit on the chassis, while the wing stays lift the rear wing position when a higher mounting point is required for added downforce. On a tuned buggy setup, this combination allows suspension and aero changes to be handled in one rear section. It suits rebuilds, replacement work and performance-focused chassis updates where damper geometry and rear wing position both play a role in track setup. Warning! Not suitable for children under 14 years.
RC tuning parts
TRF Special Damper F103GT, RC damper set
300053901soon available again
The TRF Special Damper F103GT is an RC damper set built to sharpen suspension response on compatible Tamiya formula chassis. A fluorine-coated cylinder works with a titanium-coated piston to reduce friction inside the unit, so the damper stroke stays smooth as the suspension moves over uneven track sections and through repeated corner entries. The set contains 26 pieces for damper assembly and is designed for use with the F103GT chassis as well as F104PRO II, F104Ver.II PRO, F104W, F104, TRF103, TRF102 and TRF101 platforms. The spring retainer is adjustable, and spring pressure is tuned by rotating the cylinder nut, allowing setup changes to match surface grip and handling balance. The instruction sheet also specifies a basic setting with #400 damper oil and a 3-hole piston. Damper oil is required separately. Mounted between the chassis and suspension points, the assembled dampers support more controlled movement when refining a formula car for practice sessions, setup work or repeat laps on a home or club track. This makes the set a focused upgrade for builders who want to tune suspension action with dedicated TRF hardware rather than standard kit dampers. Warning! Not suitable for children under 14 years.
RC tuning parts
TT-01/TGS Adjustable Upper Arm RC Suspension Set
300053674soon available again
The TT-01/TGS Adjustable Upper Arm set adds direct camber tuning to compatible TT-01 and TGS chassis layouts through adjustable top links and front and rear arm parts. Link length can be changed with the included flat wrench, making suspension geometry changes more straightforward during setup or maintenance at the bench. This 15-piece set is designed for TT-01 Type-E, TT-01 Type-ES and TT-01D Type-E chassis. The instruction layout shows 3 x 18 mm turn-buckle shafts used in both front and rear assemblies, with 2 rear units and 2 front units built from the included parts. Direction matters during installation, and the front and rear assemblies use dedicated arm components identified as K1, K2, K3 and K4 in the leaflet. The camber angle can be adjusted by changing rod length, opening a broader suspension setting range than fixed upper arms allow. The set suits rebuilds, replacement work and chassis tuning where wheel alignment needs to be matched more closely to running conditions. It also fits maintenance routines for existing TT-01 based cars that need fresh linkage parts or a more adjustable suspension layout. Warning! Not suitable for children under 14 years.
RC tuning parts
TT-02 Type-SRX Fr. Direct CupJoint, spare parts
300022064soon available again
The TT-02 Type-SRX Fr. Direct CupJoint is a dedicated spare parts set for service work on the TT-02 Type-SRX. Its compact layout brings together the small mechanical pieces needed for a front joint repair, with 2 black slotted housings, 2 metal pins, 2 retaining rings, 1 white round insert and 4 white C-shaped clips arranged as a matched replacement group. The slotted housings form the core of the set, while the pins and retaining rings handle the locking function that keeps the assembly together during use. The white insert and clips supply the smaller support parts that are often hardest to replace individually once wear, loss or damage interrupts a clean rebuild. Because the parts are grouped for one defined area, maintenance can stay focused on the front direct cup joint rather than drawing in unrelated components. This makes the set especially useful when a drivetrain refresh calls for the exact hardware shape intended for the TT-02 Type-SRX. On the bench, the assortment of clips, rings and pins supports careful repair work with clearly separated pieces that are easy to identify before fitting. For ongoing chassis maintenance, it serves as a practical replacement pack for restoring a worn or incomplete front joint assembly with the correct dedicated parts.
RC tuning parts
TT-02S Steel Adjustable Rear Suspension Mount
300054967soon available again
The TT-02S Steel Adjustable Rear Suspension Mount brings the adjustable rear mount system from the TT-02 Type-SR chassis to compatible TT-02 Type-S based cars. A steel mount replaces the standard rear B8 suspension plate and gives the rear suspension a firm mounting point, while the included plastic bushings change the position of the suspension shaft holes for detailed chassis setup work. Those bushing offsets do more than alter one setting. Different combinations can adjust rear toe and skid angle, and they also affect wheelbase and tread. The instruction diagram shows setup examples around the standard N1 position, with further options through N2 to N7 bushings. That makes this Hop-Up Option useful for drivers refining rear-end balance, throttle response and roll characteristics through measured geometry changes rather than broad parts swaps. On a prepared circuit car, these adjustments help tailor the rear of the chassis to surface grip and handling preference. The set is compatible with TT-02 Type-S and TT-02 Type-SR chassis cars, and it can also be used with separately sold rebound stoppers when a wider suspension setup range is needed.
RC tuning parts
W Cardan Shaft (M-Chassis), RC drivetrain set
300042300soon available again
The W Cardan Shaft (M-Chassis) brings a Double Cardan joint layout to compatible M-Chassis RC cars, giving the front drivetrain a more controlled feel as the suspension and steering work through their travel. Developed for the M-05 Ver.II R chassis kit, this Hop-Up Option is also offered as a stand-alone upgrade for selected compact on-road platforms. The set uses 2 drive shafts, 2 wheel axles, 2 joint casings and cross joint parts to build a matched left and right assembly. In use, the Double Cardan mechanism is designed to keep power transfer more consistent through steering angle changes, which is where the stated minimal deviation comes into play. The instruction reference also shows left and right orientation for the axle rings, plus a 1.6 x 9 mm shaft pin in the joint assembly. Molybdenum grease is applied to the moving contact points during assembly. Where an upright or hub carrier interferes, the instructions note trimming for clearance. Compatibility covers M-05, M-06, MF-01X and TA05 M-Four chassis cars. That makes this set a targeted choice for maintenance, rebuilds or a drivetrain update on existing M-Chassis running gear, especially when smoother joint action is the goal. Warning! Not suitable for children under 14 years.
RC tuning parts
Wheel Hub Clamp Type 4mm, RC hub set, blue
300053570soon available again
Wheel Hub Clamp Type 4mm is an RC hub set for model chassis that uses a slotted clamp mechanism to secure each hub with a cap screw. The machined aluminum construction brings precise fit to the wheel mounting area, while the blue finish gives the hardware a clean technical look on the chassis. A 2 x 10 mm stainless steel shaft sits in the axle area, the hub slides into place, and the cap screw tightens the slot to lock the assembly. This layout helps keep the shaft in position when the wheel is removed, which can make servicing and rebuild work more orderly at the bench. The set contains 4 wheel hubs, 5 cap screws and 5 stainless steel shafts, plus a hex wrench shown in the supplied reference material for installation. The assembly reference also specifies a 1.6 x 4 mm cap screw and a 1.5 mm hex wrench, with a clear note not to overtighten. Compatibility covers a broad group of touring and chassis platforms including F103GT, FF-03, FF-03 PRO, M-07 CONCEPT, M-08 CONCEPT, TA08 PRO, TA07 series, TA06 series, TA05 Ver.II, TB-Evo.6, TB-Evo.7, TB-05 PRO, TB-04, TB-03, TC-01, TRF419 series, TRF420 series and TT-02 TYPE-SR. For FF-03, FF-03 PRO, TB-03 and TA05 Ver.II chassis, use is stated with 53646 and 53647. Warning! Not suitable for children under 14 years.
RC tuning parts
XV-01 Reinforced Drive Belt, RC spare part, 573mm
300054448soon available again
The XV-01 Reinforced Drive Belt is a dedicated RC spare part for compatible XV-01 chassis setups, built to transfer power through a 573 mm continuous loop with an inner toothed profile. Its flexible construction allows the belt to run around the drivetrain path with controlled engagement, supporting steady motion between connected transmission components. The reinforced design is made to minimize friction loss while coping with the output from high power motors. That combination matters most when a drivetrain is asked to deliver repeated acceleration, longer running sessions, or sharper load changes on mixed surfaces. The toothed inner edge helps maintain positive engagement with matching pulleys, while the smooth outer surface keeps the belt compact within the chassis layout. As a replacement part, it addresses a wear point that directly affects drive efficiency and response. In workshop use, this belt suits routine maintenance, drivetrain refreshes, and targeted repairs after heavy running. It fits naturally into parts storage for XV-01 owners who keep key transmission components ready between rebuilds and track sessions.
RC tuning parts
XV-01/T Front Universal Shaft Set 42mm
300054515soon available again
The XV-01/T Front Assy. Univ. Shaft 42mm set upgrades the front drivetrain of compatible Tamiya cross platform chassis with 42 mm universal shafts that transmit drive more efficiently than dog-bone style parts. Installed at the front axle, the universal joint layout supports steadier wheel engagement through suspension and steering movement while helping the drivetrain stay connected during contact. The set contains 2 driveshafts, 2 wheel axles and 2 cross joints for a left and right front conversion. The shaft assemblies use a jointed construction that reduces the tendency of conventional dog-bone shafts to dislodge on impact, a useful change for running on mixed road surfaces where the front end is working constantly under steering input. Compatibility is stated for XV-01 and XV-01T chassis. XV-01 TC chassis models are excluded from fitment. On a rally or road setup based on the XV-01 platform, this front-end upgrade focuses on the area that sees repeated steering angle changes and surface variation. It suits maintenance, repair or drivetrain tuning work where secure power delivery and stable front axle action matter during repeated runs.
RC tuning parts
XV-01/T Rear Assy. Univ. Shaft 39mm RC Parts
300054516soon available again
The XV-01/T Rear Assy. Univ. Shaft 39mm set is a rear drivetrain upgrade for Tamiya XV-01 and XV-01T chassis models. Each 39 mm universal shaft is designed for the rear of the chassis, where it helps transfer drive more efficiently than a dog-bone style layout while keeping the joint engaged through suspension movement. The set contains 2 drive shafts, 2 wheel axles and 2 cross joints for a complete left and right rear assembly. Universal shaft construction reduces the tendency of a shaft to dislodge on impact, which is especially useful when the chassis is driven over uneven sections that keep the rear suspension working. The jointed layout also helps the rear wheels follow the road surface more consistently, supporting steadier power delivery as the chassis loads and unloads through direction changes. The metal parts shown in the set are shaped for drivetrain use, with axle and joint components that assemble into the rear transmission path. This set is intended specifically for XV-01 and XV-01T chassis compatibility. XV-01 TC chassis models are not supported, so the fit stays tied to the correct platform. In workshop use, the parts suit maintenance, replacement of worn rear driveline components, or a focused upgrade when a smoother universal-joint rear setup is preferred.
RC tuning parts
XV-02 Carbon Damper Stay F, chassis upgrade part
300022057soon available again
The XV-02 Carbon Damper Stay F is a front chassis hop-up part for XV-02 cars that replaces the standard damper stay with a 3.5 mm carbon fiber version. Its lighter, more rigid construction gives the front suspension a firmer mounting base, while the woven carbon finish and cut plate shape bring a technical look to the chassis during a bench build or trackside setup. The plate uses 3 damper attachment positions at the front, allowing suspension geometry changes through the shock mounting point rather than through a full chassis redesign. That added adjustment range helps tune how the front end reacts as surfaces and grip levels change. The set contains 1 front carbon damper stay, 4 5 mm ball connectors, 4 3 x 10 mm hex head screws and 2 5.5 x 2.0 mm spacers. The included hardware matches the mounting layout shown on the part, with multiple holes and slots arranged for precise placement. Installed on an XV-02 chassis car, this hop-up part suits drivers refining a rally or on-road setup with targeted front suspension changes. It also fits neatly into a workshop build where a standard molded stay is being swapped for a carbon fiber alternative with broader adjustment potential. Warning! Not suitable for children under 14 years.
RC tuning parts
TA-07/TRF418/417 Stabilizer Set, RC chassis tuning
300042281available in stores
This stabilizer set gives compatible 4WD touring car chassis a direct way to tune cornering behavior through front and rear roll control. The set provides 3 front wire bars in 1.5 mm, 1.4 mm and 1.3 mm diameters, plus 3 rear wire bars in 1.3 mm, 1.2 mm and 1.1 mm diameters, creating a clear spread of stiffness choices for setup work. Each wire bar carries a color-code marking, so different diameters can be identified quickly during bench setup or between runs. That makes it easier to compare axle balance changes methodically instead of relying on guesswork. The included attachment parts support a complete installation around the stabilizer layout itself, keeping the focus on suspension adjustment rather than hunting down separate mounting pieces. The set is intended for TRF418 cars and also fits TRF417 and TB04 chassis cars when they are equipped with TRF418 D parts suspension arms. On a practice day or race weekend, the different front and rear combinations allow measured changes to chassis response as grip levels and track conditions change. Batteries are not required. Warning! Not suitable for children under 14 years.
RC tuning parts: get the best out of your RC model!
With RC tuning parts, you can give your vehicle a personal touch and take its performance to the next level. Whether you want to make your RC car faster, more stable, or visually unique – you'll find the right tuning options with us to make your hobby even more exciting.
Why RC tuning parts are a must for your model
More performance, more driving fun
With the proper RC tuning parts, your model will not only stand out visually, but it will also have significantly improved driving characteristics. RC aluminium tuning parts such as shock mounts and wheel axles provide more stability and durability, ensuring you maintain full control even at high speeds or on rough terrain. Additionally, specialised motor pinions or servo mounts allow you to increase acceleration and precision. This means: even more adrenaline with every race!
Visual customisation
RC tuning isn’t just about performance – it’s also a way to make your model unique. With stylish tuning parts made from aluminium or other high-quality materials, you can give your RC car a truly personal touch. Whether it’s vibrant colours, cool rims, or custom body parts – your RC model is guaranteed to turn heads on the track.
The joy of building and optimising
A key part of RC model building is the enjoyment of tinkering and customising. With the right RC car tuning parts, you can adjust the driving behaviour to suit your needs and get immediate feedback on your work – a rewarding experience that is sure to thrill! From improved control arms to special wheel hubs: every tuning part brings your model closer to perfection.
Find the right RC tuning parts for your model
Excited to try RC tuning? Then browse through our selection and discover high-quality RC tuning parts for your model. Whether you're looking for RC aluminium tuning parts or specific components for your vehicle – we offer a wide range that makes RC car tuning a real adventure. Make your model unique and feel the difference with perfectly matched tuning parts.