Model kit accessories

Model-making abrasive material

#1500 Sanding Cloth, model hobby sanding sheet

€4.69

This #1500 sanding cloth brings controlled surface refinement to model hobby work with a fine abrasive grade and a soft sheet format. The 170 x 130 mm sheet sits comfortably in the hand and reaches flat panels, edges and smaller shaped sections where a rigid abrasive can feel less forgiving. The cloth can be used for both dry and wet sanding, making it easy to match different finishing steps and material needs. The #1500 grit is part of a 5-grade range that also includes #600, #1000, #2000 and #3000, with the number indicating the grit level. Its soft construction develops limited fold lines, a useful detail when working across visible surfaces where deeper scratch marks can interrupt the next coat or polishing stage. One sheet is included. On the bench, it suits careful smoothing between shaping, priming and finishing steps on model hobby projects. The flexible sheet format also makes it easier to wrap around contours or guide across narrow areas with steady pressure when a clean, even surface matters.  Warning! Not suitable for children under 14 years.

Model-making abrasive material

1500 Sanding Sponge Sheet, model finishing abrasive

€6.19

The 1500 Sanding Sponge Sheet brings fine surface finishing to model work with a flexible abrasive layer bonded to a cushioned backing. That combination helps the sheet sit against curves, edges and narrow parts with steadier contact than a rigid sanding surface, making it useful for refining small components by hand. The 1500 grit is suited to light finishing passes where surface texture needs to be reduced without removing too much material at once. The sponge base can be cut into smaller pieces for targeted work on tubes, rods and other shaped sections, and the sheet format leaves room to prepare custom sizes for different stages of a build. Used dry by hand, it supports controlled smoothing on detail areas, cleanup around joins and preparation before the next finishing step. On the workbench, the sheet fits the kind of close, careful handling used on scale parts, body details and other small sections that need a softer touch. It also works well when a narrow strip or small pad is needed to reach contours that are awkward for a standard flat abrasive sheet.  Warning! Not suitable for children under 14 years.

Model-making masking tapes

1mm Masking Tape, model masking tape, 18m roll

€5.791 m = €0.32

This 1 mm masking tape is made for modelling work that calls for narrow, accurate paint separation. The thin tape format follows fine contours and small sections closely, helping create sharp lines on painted and unpainted scale models. Its strong adhesive backing holds well even on uneven surfaces, which is useful around raised details, edges and shaped body sections where wider masking material can be harder to place cleanly. The tape is designed not to absorb paint colour and not to leave unsightly marks, so the masked edge stays defined and the finished surface keeps a cleaner look after removal. With a roll length of 18 m, there is enough material on hand for repeated striping, trim work and detail masking across longer build and finishing projects. The narrow 1 mm width suits fine borders, accent lines and small-area coverage on scale plastic models and radio control models. It fits naturally into paint preparation, body finishing and detail work, whether the task is isolating a slim section before spraying or protecting an adjacent painted area during careful touch-up work.

Model-making abrasive material

2000 Sanding Sponge Sheet, model finishing sheet

€6.19

The 2000 Sanding Sponge Sheet combines a fine aluminum oxide abrasive with a 5 mm flexible sponge base, giving model finishing work a controlled feel on shaped parts and delicate surface areas. On plastic models, the sheet is suited to removing small protrusions while keeping contact more even across contours, where a rigid abrasive can skip or dig in. Its flexible backing bends around curved surfaces and settles into harder-to-reach corners, which helps when refining sculpted folds, rounded panels or tight edges. The 114 x 140 mm format leaves enough area for broad passes, yet the sheet can also be cut with a modeling knife into smaller sections for narrow parts, touch-up work or repeated use at the bench. Wet sanding compatibility adds another handling option when a cleaner sanding process or a finer finish is needed. Beyond plastic models, the same sheet can be used on wood and metal finishing materials, which makes it useful across different stages of a build or restoration project. It fits naturally into surface preparation before primer, smoothing after seam cleanup, and final refinement before paint or detail finishing, especially where curved shapes call for a sanding surface that can flex with the part.  Warning! Not suitable for children under 14 years.

Model-making masking tapes

2mm Masking Tape, model supply, 18m adhesive roll

€5.791 m = €0.32

This 2 mm masking tape brings fine control to model painting where narrow lines and tidy colour separation matter. The thin tape format follows edges closely and helps create sharp, crisp borders on painted surfaces, whether the task is outlining trim, isolating small sections or protecting adjacent areas during finishing work. Its adhesive layer is designed for modelling use and holds well even on uneven surfaces, which is useful around contours, panel shapes and small raised details. The tape also resists absorbing paint colour, helping maintain a clean barrier while work is in progress. That combination supports accurate masking on both unpainted parts and already finished sections where neat transitions are needed. The translucent amber roll format also makes it easier to place short lengths with visual control during detailed work. With 18 m on the roll, the tape suits repeated use across multiple sessions at the bench, from body detailing on radio control models to careful paint separation on scale plastic builds. It can be applied for narrow stripes, edge definition and small-area masking wherever a broader tape would cover too much surface.

Model-making abrasive material

3000 Sanding Sponge Sheet, model sanding sheet

€6.19

The 3000 Sanding Sponge Sheet brings controlled finishing to model work with a flexible sponge base and an aluminum oxide abrasive surface. Sized at 114 x 140 mm with a 5 mm sponge thickness, it adapts to shaped parts while keeping a broad working area for steady, even passes across detailed surfaces. Its fine 3000 grit suits light refining work where raised spots, small imperfections and transition areas need a smoother finish before the next stage. The sponge base bends into curved sections and reaches corners that are awkward with a rigid sanding block, which helps when working on body lines, clothing folds or other sculpted details. Because the sheet can be cut with a modeling knife, smaller sections can be prepared for narrow parts or confined areas instead of using the full sheet each time. Wet sanding use adds another practical option for controlled finishing on plastic models, and the abrasive surface is also stated for wood and metal materials. On the bench, the sheet supports careful cleanup after assembly, surface preparation before paint, and final touch-up work on shaped components. Cut sections can be kept beside files, knives and other finishing tools for repeated detail work on corners, edges and curved forms.  Warning! Not suitable for children under 14 years.

Model-making tools

40ml Square Bottle Holder, model accessory, 80x80mm

€3.89

This 40 ml Square Bottle Holder adds a simple layer of control to model-building work by surrounding a square bottle with a PE sponge frame sized at 80 x 80 x 12 mm. The snug fit helps limit tipping if the bottle is knocked during cement application, keeping the work area steadier while parts, tools and materials are spread across the bench. The holder is intended for the 40 ml square bottles used for modeling cement and similar aids, so the bottle sits within a cutout rather than balancing on its own base. That extra support matters most during close brush work, when a hand, sleeve or tool can catch the bottle edge. The PE sponge material keeps the format light and easy to place, and the single-holder design makes it easy to position one bottle exactly where the current build needs it. An included tab also allows multiple holders to be linked together for a more ordered arrangement of bench liquids. On a busy workbench, the holder helps separate cement from painted parts, decals and unfinished assemblies by giving the bottle a defined place. It also suits longer building sessions where the same adhesive is picked up and set down repeatedly, keeping the bottle stable and close to the active work area.

Model-making tools

A4 Cutting Mat, hobby craft mat, 320 x 225 mm

€16.79

This A4 cutting mat brings a measured, stable work surface to model making and paper craft, with a 320 x 225 x 2 mm format that sits neatly on the bench while still extending slightly beyond standard A4 paper. The green surface carries printed reference markings that keep trimming, alignment and layout work clear at a glance. The front side combines a 1 cm grid, 10-degree angle guides, a 1 mm step ruler, curved markings and circular references, giving one surface for straight cuts, angled lines and repeated shape work. A 3-ply structure places a hard inner layer between softer outer layers, a construction designed to leave cut traces less conspicuous and help preserve blade sharpness over longer use. The reverse side is plain, so the mat can be turned over when a clean surface suits the task better. The printed markings are intended as guides, and precise measurement work should still be checked with dedicated measuring tools. On the bench, the mat supports jobs such as trimming sheet material, cutting paper patterns, preparing masking shapes and setting out small model parts before assembly. It should be stored flat and kept away from high temperatures to help prevent warping over time.

Other accessories

Anaerobic Gel Thread Lock, model adhesive, red 1g

€8.29

Anaerobic Gel Thread Lock is a model adhesive designed to help keep threaded metal parts from working loose during R/C use. The red gel format supports controlled placement on screw threads, so the compound stays where it is needed on small fasteners in vehicles, chassis sections and engine-related assemblies. The 1 g container is sized for precise hobby maintenance rather than broad surface bonding. Its anaerobic formula is intended for threaded connections, where it works within the joint instead of acting like a general-purpose glue across exposed surfaces. That makes it useful for screws and other metal fittings that face repeated vibration, regular handling and ongoing setup changes. The compact jar format also keeps the compound close at hand on a workbench for quick application during servicing. In practical use, a small amount can be placed on the thread before fastening a metal part into position on an R/C chassis or engine assembly. It suits routine maintenance sessions, rebuilds after running, and fresh installations where a more secure threaded hold is needed on metal hardware.

Model-making tools

Angled Round Tip Tweezers, Craft Tool, Steel

€18.49

These angled round tip tweezers bring clear sightlines and controlled handling to close-detail work. The bent tip profile helps approach small parts from the side instead of directly above, which can make placement easier when working in confined areas or around raised details. The steel body gives the tool a precise, clean feel, while the broad flat grip section supports stable finger placement during slow, exact movements. The round tip form is suited to delicate handling where a sharp point would be too aggressive, making it useful for lifting, turning or settling fine materials into place. In model making, the angled shape can help when positioning markings, adjusting miniature components or guiding small pieces into narrow openings. The slim profile also suits electronics handling and other bench tasks that call for careful control over tiny parts. On a hobby desk, these tweezers fit naturally alongside assembly, finishing and detail correction work. They support steady placement during miniature builds, careful repositioning during surface detailing, and neat handling whenever fingertips are too large for the job.  Warning! Not suitable for children under 14 years.

Model-making tools

Angled Tweezers, model tool, stainless steel

€12.99

These angled tweezers bring precise control to close-up model work, with bent fine tips that make it easier to reach small parts and place decals where a straight tool can get in the way. The angled form keeps the working point visible during careful positioning, which helps when aligning tiny pieces on detailed builds. The tweezers are made from stainless steel and finished with a black cationic coating. This combination gives the tool a clean, technical look while supporting long-term workshop use. Rounded edges are designed to prevent scratching, an important detail when working near painted surfaces, clear parts or freshly applied markings. The slim body suits delicate handling tasks such as lifting, turning and adjusting small components during assembly or finishing. On the bench, the tool fits naturally into decal application, part placement and other fine correction work that calls for a steady grip and a narrow contact point. It also works well as a dedicated craft tool kept alongside knives, files and cutters for repeated detail sessions on scale models.  Warning! Not suitable for children under 14 years.

Other accessories

Anti-Slip Sticker, model supply, 75 x 150 mm

€4.19

This anti-slip sticker sheet adds controlled grip exactly where small parts, tools and work surfaces tend to shift. The 75 x 150 mm size gives enough area for display bases, rulers, mats or custom cut sections, while the synthetic rubber face creates traction and the acrylic adhesive underside holds the sheet securely after placement. At about 0.4 mm thick excluding the backing film, the material stays slim enough for close contact on precision tools and flat working areas. The polyester cloth base supports the sheet structure while keeping it flexible enough to adapt to different applications. On metal rulers and cutting mats, the added grip helps keep the contact area steadier during cutting work. Applied to tweezer tips, the surface helps hold small parts more securely. Two sheets can also be combined to create a double-sided anti-slip layer for custom workshop setups. The sheet also suits bench and display use where movement needs to be reduced without adding bulky pads. It can be placed under finishing abrasives so the abrasive stays put while a part is moved back and forth across the surface, supporting cleaner, more controlled filing and sanding work.  Warning! Not suitable for children under 14 years.

Model-making tools

Basic Drill Set, model tool, 1.0 to 3.0 mm

€17.99

The Basic Drill Set brings 5 drill sizes into one compact model tool set, covering 1.0 mm, 1.5 mm, 2.0 mm, 2.5 mm and 3.0 mm for precise hole work across a wide range of hobby tasks. This spread gives a practical progression from fine starter holes to larger openings when parts need a broader pass. Each diameter serves a distinct role during model preparation and finishing. Smaller bits can be used where narrow openings or careful pilot points are needed, while the larger sizes support follow-up drilling when fittings, posts or mounting points call for more space. Keeping these 5 sizes together makes it easier to select the required diameter for the next step instead of working around a single fixed size. The set format also keeps the focus on measured, deliberate drilling rather than improvised tool choices. On the bench, the range suits routine workshop jobs such as preparing parts, adjusting openings and refining fit before final joining. It also works well for hobby sessions that move between delicate detail work and broader drilling tasks, with each bit size ready for the specific opening required.

Model-making tools

Basic File Set (3), modeling tool set, 16 cm

€10.79

The Basic File Set (3) brings 3 distinct file shapes into one compact modeling tool set for controlled shaping, smoothing and edge work. Flat, round and half-round profiles make it easier to match the filing surface to the part being worked, whether the task involves straight edges, drilled openings or curved contours. Each file measures about 16 cm in length, giving a hand-friendly format for bench work where smaller parts and tighter areas need steady control. The set is specially developed for modeling use, with double-cut surfaces that support material removal on plastic and soft metals. That combination suits cleanup after cutting, refining contact points, easing tight fits and smoothing visible areas before the next build step. On a workbench, the flat file can true edges and level small surfaces, while the round file reaches into holes and narrow recesses. The half-round profile helps follow curved sections where a flat face alone cannot sit cleanly. Black handles support a firm grip through repeated strokes, keeping the focus on accurate hand finishing across hobby, craft and model-building tasks.  Warning! Not suitable for children under 14 years.

Model-making tools

Bending Plier for Photo Etched Craft Tool

€34.49

The Bending Plier for Photo Etched is made for the precise shaping work that gives scale builds a cleaner, more refined finish. Its long, narrow metal jaws reach small tabs and edges on photo-etched parts, making controlled bends easier when working with thin stainless metal components that demand a steadier touch than standard molded parts. A spring loop between the handles keeps the jaws open after each movement, so the plier is ready for the next adjustment without constant resetting. This helps when a part needs to be held, aligned and bent in short, careful steps. The curved black handles support a stable grip during close bench work, especially when handling tiny detail pieces where finger placement and pressure matter. In a photo-etched workflow, the plier covers the shaping stage after parts have been cut free and cleaned, giving fine metal additions their intended form before placement on the model. On the workbench, it suits tasks such as folding tabs, refining edges and positioning narrow stainless metal details before attachment. The compact, precision-led format also fits careful touch-up work on hard-to-reach areas where broader tools can get in the way.  Warning! Not suitable for children under 14 years.

Model-making adhesive

Body Set R/C PC Reinf Mesh Tape, hobby tape

€10.791 m = €5.40

This reinforcing mesh tape gives polycarbonate body shells a practical way to add support exactly where repeated impacts and flex can wear down vulnerable sections. Supplied as a 2 m roll with a 35 mm width, it suits targeted reinforcement on spoilers, fenders and similar areas inside an R/C body, where extra backing helps stressed sections stay usable for longer during regular running and repair work. The mesh format is the key to how it works. Instead of covering a large section with a rigid patch, the open structure can be positioned on the inside of the shell over the area that needs support. Clear silicone adhesive is required separately to fix the tape in place. That method makes it easier to reinforce curved contours and narrow sections without adding a bulky layer, which is especially useful around edges, bends and other high-strain points on lightweight polycarbonate shells. On the workbench, the roll format keeps material ready for quick trimming when a body picks up cracks, weak spots or stress around exposed sections. It also suits planned reinforcement before the next session, whether the focus is on spoiler edges, wheel arch areas or other parts of the shell that see frequent contact.

Model-making tools

Conical File 1.5-8 mm, hobby tool, #200 finish

€24.49

This conical file is built for precise modification work on molded parts with holes, using a tapered filing surface to reach areas that flat tools cannot address cleanly. With an overall length of 150 mm, a 55 mm file section and a working diameter range from 1.5 mm to 8 mm, it supports controlled shaping of narrow openings, rounded cutouts and gradually widening holes on model parts. The #200 grade finish is tuned for fine adjustments rather than aggressive removal, making it useful when a part needs a cleaner edge, a more accurate opening or a smoother transition inside a curved recess. The conical form allows contact at different points along the taper, so the same tool can work near the tip for smaller openings or farther down the file for broader shaping. An embossed grip supports a secure hold while changing the filing angle across detailed surfaces. A transparent cover protects the filing section when the tool is stored in a drawer, toolbox or hobby case. On the workbench, this file suits careful fitting and cleanup on molded components that need subtle correction before final assembly or finishing. It is especially useful during test fitting, edge refinement and detail preparation where a gradual taper gives more control than a straight file.

Other accessories

Cotton Swab round extra small, hobby applicators

€5.69

These round extra small cotton swabs are made for scale model work where control matters more than bulk coverage. Tightly spun cotton tips keep a cleaner shape during painting, decal application and panel lining, so small corrections and fine placement feel more deliberate at the workbench. Each swab uses an extra small head with an 8.5 mm tip length and a 2.2 mm diameter, which helps reach confined sections and narrow surface details without flooding the surrounding area. The industrial strength build is designed for hobby use rather than general household tasks, so the cotton resists fraying more effectively when wet or dipped in solvents. That makes them useful for subtle weathering, careful cleanup around markings and controlled application of finishing media on compact parts. The round tip shape also suits gentle blending and small circular motions where a pointed edge is not required. A pack of 50 supports repeated use across long build sessions, whether the task is settling decals onto body panels, refining panel lines or adding weathering to small areas such as Waterline series models. They also work well with Weathering Master Set colours when rust stains and other surface effects need a measured, local application.  Warning! Not suitable for children under 14 years.

Other accessories

Cotton Swab round small, hobby applicator, 50 pcs

€5.69

This pack of 50 small round cotton swabs is made for scale model work where clean application and control matter. The tightly spun cotton tips keep their form more reliably than common supermarket swabs, which helps when placing decals, refining panel lines or working paint into small sections. With a 3 mm tip width and a 12 mm tip length, the swab reaches confined areas while keeping contact focused. The industrial strength design is intended for hobby use, including work with wet media and solvents. Because the cotton frays less easily, the swab leaves less loose fibre behind during detail work and reduces wasted material. The round tip shape suits dabbing, blending and controlled transfer on model surfaces, especially where a brush may carry too much material at once. It also supports weathering effects in small zones, such as rust staining and subtle surface variation. On ship subjects, aircraft details or other compact assemblies, the slim double-ended format helps move from one section to the next without changing tools immediately. The swabs can also be used with Weathering Master Set colours when building up fine effects on corners, seams and other narrow points of the model.  Warning! Not suitable for children under 14 years.

Other accessories

Cotton Swab round, hobby applicator, 50 pieces

€6.59

These round craft cotton swabs are made for scale model work where control at the tip matters. Each swab uses tightly spun cotton that keeps its shape more reliably during painting, decal application and surface detailing than loosely wound household alternatives. The pack contains 50 swabs, giving a practical bench supply for repeated finishing sessions. The round tip measures 12.5 mm in length and 3.5 mm in width, a format suited to broader contact on small model sections while still staying manageable around edges and recessed detail. When the tip is wet or dipped in solvents, the industrial strength construction helps it resist fraying, so the cotton stays more consistent during cleanup, blending and correction work. This makes the swabs useful not only for placing decals and working panel lines, but also for refining weathering effects and applying color from weathering sets to focused areas. On the workbench, the swabs fit naturally into the finishing stages of a build: smoothing decal edges, adjusting panel line application, lifting excess material or adding subtle rust and dirt effects. The round head shape also suits repeated passes over compact surfaces where a pointed tip would cover less area with each stroke.  Warning! Not suitable for children under 14 years.

Other accessories

Cotton Swab Tria.extra small, hobby applicators

€6.69

These extra small Tria. cotton swabs are made for model finishing where a standard household swab can feel too soft or lose its form too quickly. The tightly spun triangular cotton tips create a more defined contact area for careful work on decals, panel lining and other small surface details, especially where edges and corners need a narrower touch. Each pack contains 50 swabs, and the double-ended format puts a working tip on both sides for repeated use across painting and weathering steps. The tip section measures 8 mm, with a slim 2.3 mm profile that suits compact parts and fine surface sections. Compared with loosely spun supermarket swabs, these industrial strength swabs are designed to fray less easily when wet or dipped in solvents, which helps keep the cotton shape more consistent during detailed bench work. They fit naturally into scale model routines, from pressing decals into recessed lines to applying weathering colors in small zones. On compact subjects such as Waterline series models, the triangular tip shape helps target tight areas where broader applicators can leave excess color or disturb nearby detail.  Warning! Not suitable for children under 14 years.

Other accessories

Cotton Swab Tria.medium 50-Piece Cleaning Set

€5.69

The Cotton Swab Tria.medium pack brings a precise, workshop-ready format to detailed cleaning and careful surface work. With 50 swabs in the pack and a double-ended layout, each piece offers two usable cotton tips on a slim white stem, making it easy to keep work moving during maintenance, touch-up preparation or dust removal around small parts. Each cotton head measures 10.5 mm in length and 4.5 mm in width, giving this Tria.medium format a balanced size for controlled contact on narrow sections, edges and recessed areas. The cotton surface supports gentle handling on finished components where a firmer tool would be less suitable. The medium tip size also suits jobs that need more coverage than a very fine point while still staying focused on small zones rather than broad wiping. On a hobby bench, these swabs fit naturally into routine care for models, tools and display pieces. They can be kept close at hand for cleaning sessions, detail work between build stages or careful upkeep of visible surfaces where neat, measured application matters.  Warning! Not suitable for children under 14 years.

Model-making tools

Craft Knife II hobby cutter with auto-lock blade

€6.39

Craft Knife II combines a slim retractable format with an ergonomic black handle and a stainless steel segmented blade for precise hobby cutting. The auto-lock slider fixes the blade at the selected extension, helping maintain a steady feel when trimming masking film, scoring sheet material or cutting clean lines through paper and card at the workbench. The blade is made from high-carbon stainless steel with a thickness of 0.38 mm, a detail that supports a fine cutting edge while adding resistance to rust. When the cutting edge dulls, the rear clip detaches by squeezing the tabs on both sides and serves as a blade snapper for removing worn sections. The blade can also be removed, reversed and reinstalled for left-handed use, so the same knife adapts to different hand positions without changing the handle layout. Commercially available small cutter knife replacement blades are compatible. On a model bench, in a craft corner or beside a cutting mat for decal and masking work, the compact body keeps the tool easy to place, pick up and reset between cuts. The retractable blade format also suits short, repeated trimming passes where controlled extension matters as much as edge sharpness.  Warning! Not suitable for children under 14 years.

Model-making tools

Craft Saw Blade, replacement hobby saw blade

€6.99

This craft saw blade brings fine-toothed cutting control to detailed hobby and model work. The slim metal form, long rectangular profile and narrow toothed edge suit careful trimming, separating and shaping where a broader workshop saw would feel too coarse. A rounded front tip helps the blade move into tighter working areas while keeping the cutting edge clearly visible during each pass. The blade is shown as a standalone replacement part with a circular mounting hole for fitting to a compatible handle. Its dark metal surface and brushed finish keep the form easy to read on the bench, especially when following marked lines or working close to small components. The continuous row of fine teeth along one side is geared toward measured hand movement rather than fast rough cutting, which makes it useful for controlled material removal in model building, craft assembly and detail work. On the workbench, this blade suits jobs such as trimming sheet material, refining openings and separating delicate sections before sanding or final fitting. It also works well as a spare blade kept alongside other hobby tools, ready for precise hand cutting when a knife or larger saw is not the right match.

Model-making tools

Craft Tools Bending Tweezers for PE Parts

€23.99

Craft Tools Bending Tweezers for PE Parts are made for the precise handling and shaping that photo-etched details demand. The stainless steel tool is designed for brass and nickel silver parts, with a slim 100 mm format that sits neatly in the hand while working over small model assemblies and etched fittings. Unlike general-purpose tweezers, this tool is built around the bending task itself. The tips are made as thin as possible so they can be positioned directly along a fold line before the metal is bent by hand. That close contact helps keep narrow tabs and fine edges aligned while forming crisp angles on delicate components. The tweezers can be used on fold lines up to 10 mm in length, which suits many of the small brackets, panels and detail sections found in photo-etched parts sets. For model builders working with finer metal additions, that focused geometry gives more control than a standard pickup tool. On the bench, the compact length supports careful work in tight spaces around unfinished assemblies, detail sprues and small subassemblies. The stainless steel construction also suits repeated use as part of a regular modelling tool set, whether shaping a single etched flap or preparing several metal details for a larger build.  Warning! Not suitable for children under 14 years.

Model-making tools

Curved Scissors for Polycarbonate Hobby Trimming

€19.49

These curved scissors are made for the precise trimming work that polycarbonate R/C car bodies demand. The stainless steel blades combine a slim profile with a curved cutting edge, giving clear access to shaped sections where flat tools can be awkward to position. Around wheel openings, roof edges and molded corners, the blade shape helps follow the line of the body with a steadier cutting path. The compact format suits close hand work on hobby benches, where small adjustments often matter as much as the main cut. The curved blade tip reaches into formed contours with less repositioning, which helps when refining openings after the main body shape is removed. Stainless steel construction gives the cutting edges a solid, workshop-ready feel for repeated use on polycarbonate shells and other detailed trimming tasks linked to model body preparation. Used during body finishing, these scissors support careful shaping before painting, mounting and final assembly. They fit naturally into R/C car build sessions where clean edges and controlled cuts help the bodyshell sit neatly and keep the finished outline crisp.  Warning! Not suitable for children under 14 years.

Model-making tools

Curved Scissors, PC Body Tool, 12 mm Blade

€31.49

These curved scissors are made for detailed trimming work on polycarbonate model bodies, where a clean line matters as much as the paint and decals that follow. The 12 mm blade size keeps the cutting area compact, making it easier to guide the edge through tight curves, narrow openings and shaped sections that appear around wheel arches, windows and cockpit cutouts. The curved blade profile changes how the tool meets the material. Instead of forcing a straight path through rounded shell sections, the cutting edge follows the contour more naturally, which helps reduce awkward hand repositioning during fine trimming. On thin polycarbonate sheets, that added control is useful when separating molded sections, refining body edges or cleaning up small areas after the first rough cut. The format suits bench work where precision matters more than reach. In a model building setup, these scissors slot in alongside knives, reamers and sanding tools as a dedicated option for curved cuts. They are especially useful during body preparation, when shell openings and perimeter lines need steady, repeatable shaping before mounting and finishing continue. Their focused 12 mm blade size keeps the tool aimed at detail work rather than broad sheet cutting.

Model-making tools

Cutting Mat α A4, hobby mat, 300 x 220 mm

€15.99

The Cutting Mat α A4 brings a compact 300 x 220 mm work area to model benches where clean cuts, measured layouts and repeatable alignment matter. Its 2 mm thickness and translucent blue finish create a clear visual base for trimming sheet material, marking lines and setting small parts in place during close-up hobby work. The surface is printed with more than a standard grid. In addition to straight measurement guides, it carries R curves and dedicated lines for cutting masking tape, which helps when preparing paint masks or repeating narrow tape widths. The mat is made from low-odor olefin resin, a practical choice for indoor bench use where tools, parts and markings stay close at hand. A 3-layer structure places a hard inner core between softer outer layers, guiding the knife edge through repeated passes while helping reduce wear on blades. The printed markings serve as layout guides for cutting and positioning tasks across model and craft work. On a worktable beside a ruler, knife and small components, the A4 format fits neatly into limited space while still leaving room for measured cuts and angle checks. It suits routine bench tasks such as trimming masking material, sizing styrene pieces, marking curves and keeping small-scale hobby work organized in one defined area.

Model-making tools

Cutting Mat α A5, hobby cutting mat, blue

€10.29

The Cutting Mat α A5 brings a compact 220 x 150 x 2 mm work surface to model making, craft cutting and bench preparation, with a translucent blue finish that stays easy to read under strong task lighting. Its A5 footprint suits smaller desks, side tables and portable tool setups where clean measuring and controlled knife work need to happen in a limited space. Across the printed face, the mat combines edge rulers with millimeter markings, a measurement grid, angle guides, circular references and a large protractor-style semicircle. Radius curves marked from R100 to R500 add a practical reference when shaping or checking rounded sections. The reverse side is plain, giving a second working face when a clear surface is preferred for layout tasks. The olefin resin material is described as low odor, which helps during longer indoor sessions focused on trimming parts, preparing paint masks or sizing sheet stock. On the bench, the printed tape-cutting lines support repeatable masking strips when a ruler and hobby knife are used together. The mat suits detail tasks such as measuring small components, setting cut angles and preparing curved templates before assembly or finishing work begins.

Model-making tools

Decal Scissors, model tool for precise trimming

€24.49

These Decal Scissors bring fine control to 2 common model workshop jobs: trimming paper decals and cutting soft R/C racing rubber tires. The carbon steel construction and pointed blade shape support close, accurate cuts where larger scissors can feel clumsy, whether working around small printed markings or removing thin flash from molded tire edges. For decal work, the narrow tip helps separate intricate shapes from the sheet with less excess paper left around the design. For tire prep, the blades can trim molding flash from soft racing rubber and also support precise modifications when a track setup calls for a specific cut pattern. The compact format suits bench work where small movements matter, and the sharp cutting edge is intended for detail-focused handling rather than broad general-purpose cutting. To preserve the cutting edge, the scissors are intended for paper decals and should not be used on vinyl stickers. On a model bench, they fit naturally beside paint, tweezers and sanding tools during the finishing stage. At the track, they help clean tire edges or prepare a fresh set of rubber before setup changes, giving builders and racers a focused tool for neat, exact trimming work.  Warning! Not suitable for children under 14 years.

Model-making tools

Decal Tweezers, hobby tool with angled tips

€22.49

These decal tweezers are shaped for careful handling of both small and larger transfers, giving model work a more controlled touch where printed markings need exact placement. The angled tip makes it easier to approach surfaces at a clear working angle, whether positioning a narrow stripe along an edge or settling a larger graphic onto a curved section. The stainless steel body brings a slim, precise format suited to close bench work, while the tip geometry divides the task by size. Smaller decals can be picked up delicately at the pointed ends, where fine contact helps with detailed alignment on compact areas. Larger decals are supported lower down the tip, allowing a broader hold that helps keep the transfer flat while it is moved into place. This split handling approach is the key mechanism of the tool: the same tweezers use the point for fine markings and the lower tip area for wider pieces. On a model-building bench, that means one tool can move from tiny insignia to broader printed graphics without changing grip or reaching for a second pair. Used alongside water-slide markings during finishing work, the angled form helps maintain a clear view of the placement area while guiding the decal onto the target surface.  Warning! Not suitable for children under 14 years.

Model-making tools

Design Knife Blade (30), replacement blades

€5.69

Design Knife Blade (30) supplies a fresh cutting edge for detailed hobby work, with 30 replacement blades stored together in a plastic container for orderly handling between sessions. The blade shape suits fine trimming, scoring and close detail work where controlled cuts matter on small parts and precise outlines. As a replacement accessory for the Design Knife, this set focuses on keeping cutting performance consistent as edges wear through regular use. Swapping a worn blade promptly helps maintain a cleaner cut and steadier handling during modelmaking, craft preparation and careful finishing work. The compact storage case keeps the blades contained in one place on the bench and helps separate unused blades from loose tools and materials. On a build table, the set supports repeated detail tasks such as trimming film, refining edges or cutting small shapes with a sharper working edge available when needed. It also fits neatly into a regular hobby supply setup, where spare blades are kept ready for ongoing assembly, finishing and workshop use.

Model-making tools

Design Knife, hobby craft knife with 30 blades

€12.99

The Design Knife brings fine control to trimming, scoring and detail cutting, with a sharp triangular blade mounted in a metal chuck and a black and gold handle shaped for steady hand work. Ridged and knurled grip areas support careful guidance when working along narrow edges, small openings or precise cut lines on model-making materials. The blade format suits close, deliberate cuts where a larger craft knife would feel less exact, and the metal chuck keeps the mounted blade aligned during detailed work. A set of 30 replacement blades extends the knife's working life across repeated bench sessions and keeps fresh cutting edges close at hand. Protective cap parts are also included for covered storage between uses. The visible Made in JAPAN marking identifies the origin stated on the tool itself. On a model bench, the knife supports clean trimming of parts, careful scoring before separation, and small corrective cuts during finishing work. It also fits general hobby and craft tasks that call for a narrow blade tip, controlled pressure and a compact handle that stays precise in the hand.

Model-making tools

Diamond File for Photo Etched, hobby file

€11.29

The Diamond File for Photo Etched is a precision hobby tool made to refine thin metal details with more control than a standard file. Its diamond abrasive surface is suited to light carving on hard materials such as stainless metal, helping clean up edges on photo-etched parts while keeping the work focused and accurate. The slim profile and pointed working end also make the tool useful for narrow grooves, corners and other small sections that need careful finishing. A key advantage of this file is the way it moves across delicate etched metal. The surface files equally well in any direction, so shaping strokes can follow the angle of the part instead of forcing a single filing path. It is also designed not to snag on thin photo-etched sections, which matters when working with fine tabs, cut lines and small decorative details. The half-circle shape adds another practical benefit by reaching into curved or recessed areas that are awkward with flatter tools. On the bench, this file fits naturally into the finishing stage after parts are cut free and before bending or final placement. It helps remove flash, smooth contact points and tidy hard-to-reach areas on detailed model assemblies where a clean metal edge changes the final look.  Warning! Not suitable for children under 14 years.

Other accessories

Display Case C, model display case, 1:20 and 1:24

€21.99

Display Case C gives finished scale models a clean, defined setting with clear walls and a mirrored base insert that brings underside detail into view. Sized for 1:20 racing cars and 1:24 sports cars, it turns a completed build into a focused display piece rather than leaving it exposed on an open shelf. The case has inner dimensions of 247 x 133 x 92 mm, giving compact vehicle models a measured fit that suits low, wide body shapes often seen in racing and sports car subjects. Outer dimensions of 260 x 144 x 105 mm keep the overall footprint manageable for cabinets, desks or hobby rooms. The mirror sheet applied to the base adds a second viewing angle, so chassis parts, floor shaping and lower body contours remain visible without lifting the model. Placed in a collection cabinet, on a workbench or in a study, the case helps present a finished model with a more deliberate layout. It also suits display after painting, decaling and final assembly, when surface finish and stance deserve a clear, unobstructed view.

Other accessories

Display Case P, display case for 1:20 and 1:700

€25.99

Display Case P gives finished scale builds a defined presentation with a clear acrylic cover and a black molded base. Sized for selected 1:20 car models and 1:700 Water Line Series subjects, it turns a completed build into a clean display piece while keeping the shape and finish fully visible. The acrylic upper section offers high transparency, so body lines, paintwork, deck structures and small markings remain easy to see through the cover. Inner dimensions of 287 x 132 x 93 mm provide the enclosed display space, while the outer dimensions of 299 x 145 x 106 mm help when planning shelf or cabinet placement. The product data also lists dimensions of 260 x 144 x 105 mm, but this measurement conflicts with the stated inner and outer sizes and is therefore not used here. On a desk, in a hobby room or inside a display cabinet, the case gives a finished model a clear boundary and a tidier presentation. It suits builders who want to keep a completed car or Water Line subject together in one covered space while leaving the details visible from the outside.

Model-making tools

E-Ring Tool 2 mm, model tool for tiny clips

€11.29

The E-Ring Tool 2 mm is a dedicated hand tool for one of the fiddliest jobs in RC model building: fitting and removing tiny 2 mm E-rings. Its specially designed tip uses a unique shape to catch the clip securely, making small fastening work easier to control during construction and maintenance. Instead of relying on general-purpose pliers or improvised tools, this format focuses directly on the narrow opening and small contact area of 2 mm E-rings. The forked working end helps guide the clip onto its groove or lift it away again when a model needs servicing. That targeted shape is especially useful around compact assemblies where retaining clips sit close to moving parts and limited space makes precise handling more important. The slim tool body keeps the action close to the fingertips for careful placement. On the workbench, it suits repeated jobs such as drivetrain upkeep, suspension service or replacing worn parts that use small retaining clips. During a fresh build, it helps keep clip installation neat and controlled; during maintenance, it supports quicker removal when parts need to come apart for cleaning or replacement.  Warning! Not suitable for children under 14 years.

Model-making tools

Engraving Blade Holder, craft tool, aluminum

€18.99

The Engraving Blade Holder combines a slim pen-style form with a 126 mm length and 6 mm diameter, giving precise hand control for fine engraving, scribing and trimming work on model parts. Its lightweight aluminum body keeps handling nimble during careful passes along panel lines, edges and marked cutting paths. A knurled grip section supports steady finger placement, while the chuck in nickel-plated brass secures the blade in the holder. Blade insertion and removal follow a direct sequence: lightly pinch the chuck, rotate the handle to loosen it, place the blade, then tighten the handle again. This mechanism keeps blade changes straightforward when switching between different detailing tasks. The holder is compatible with Fine Engraving Blades 74135, 74136, 74137 and 74138, and also accepts the Design Knife Blade 74074. On the bench, the slim profile suits close, deliberate movements when refining grooves, extending panel lines or cutting precise shapes from sheet material. A protective cap is included to cover the tip in storage, and it can also be fitted to the end of the handle during use to help prevent the holder from rolling across the work surface.  Warning! Not suitable for children under 14 years.

Model-making tools

Fine Craft Knife, hobby knife, stainless steel

€13.49

The Fine Craft Knife brings slim stainless steel construction and a segmented precision blade to detailed hobby cutting. Its pen-like shape and stepped slider make it easy to set a short extension for close trimming or a longer reach for straight cuts on paper, masking film and similar light materials at the workbench. The black sliding lock section secures the blade position once set, which helps keep handling consistent during careful edge work. Snap-off blade segments provide a practical way to renew the cutting edge when one section becomes worn, so fine lines and clean corners stay easier to manage over repeated sessions. The narrow metal body keeps the tool compact in storage and easy to place alongside rulers, cutting mats and other bench essentials. Visible blade markings indicate stainless steel construction, and the overall format is suited to model finishing, decal preparation and small craft adjustments where accuracy matters more than force. On a model bench, the knife supports tasks such as trimming masking shapes, cleaning excess material from edges and scoring thin sheet stock before separation. It also fits general craft use for neat, controlled cuts in projects that call for a light touch and a clearly guided blade path.  Warning! Not suitable for children under 14 years.

Model-making tools

Fine Craft Saw blade III, hobby saw set, 0.15 mm

€11.29

Fine Craft Saw blade III is a hobby saw set for narrow, controlled cuts where a normal modeling saw would remove too much material. The etched metal blades are just 0.15 mm thick, so the cut stays fine and helps avoid unwanted changes to the length of small parts during model work. The sheet provides 4 blade formats for different cutting situations, with each profile shaped to suit a particular kind of access or cutting line. Fold-over grips let the blades mount onto a Modeler's Knife Item 74040 for a pen-like hold and close control during careful trimming. The metal sheet marking shows the blade variants as III-A, III-B, III-C and III-D, which helps keep the different shapes clearly organised before use. The visible SUS304 marking identifies the stainless steel material used for the etched blade sheet. This tool set suits detailed bench work such as adjusting fitted parts, opening narrow cuts, or separating small sections where accuracy matters more than cutting speed. In model building sessions with tight tolerances and delicate components, the slim blade profile supports cleaner planning before sanding, fitting, or final assembly.

Model-making tools

Fine Craft Saw Blades, scribing tool set 0.1 mm

€11.79

This set of Fine Craft Saw blades is made for precise scribing and detail recovery in model work. The 0.1 mm stainless steel construction supports narrow cuts when seam cleanup has softened surrounding detail, and it also helps deepen existing panel lines with a controlled, fine kerf. On the etched sheet, 6 blades are arranged in 2 rows of 3, ready for careful removal and use at the bench. The blade selection combines straight profiles with rounded profiles, which gives more flexibility across flat sections, curved bodywork and tighter access points. Compared with Item 74094, these blades use smaller teeth and a finer pitch, which suits more delicate surface work where heavier cutting action would be too coarse. The material is stainless steel, and the thin profile keeps the cutting edge focused on light engraving and detail correction rather than broad removal. Fold the grips over and the saws can be used on their own for close hand control during panel restoration, trim work or fine surface adjustment. When a longer handle is preferred, the blades may also be fitted to Modeler's Knife Item 74040. At the workbench, that combination supports steady passes along engraved lines, corners and shaped sections on scale models.

Model-making tools

Fine Drill Bit 0.3 mm, model tool accessory

€6.49

The Fine Drill Bit 0.3 mm brings exact sizing to delicate model-making tasks where a very small opening matters. With its 0.3 mm diameter, it supports careful drilling for fine detailing, subtle modifications and other close-control bench work on miniature parts. This single drill bit is suited to jobs that call for a narrower diameter than standard hobby bits can offer. It can be used to prepare tiny holes for detail placement, light pinning work or other precision steps during a build, while keeping material removal to a minimum. The compact accessory format makes it easy to keep alongside knives, files and other workshop essentials used in scale modelling. On the workbench, the 0.3 mm size is especially useful when a project needs measured, hand-led accuracy rather than a broader cut. It fits naturally into careful model assembly, detailing and finishing routines, whether the task involves refining a small component or preparing a precise point for the next build step.  Warning! Not suitable for children under 14 years.

Model-making tools

Fine Drill Set, hobby drill bit set, 0.3-0.8 mm

€18.49

This Fine Drill Set brings 5 micro sizes together in one compact format, giving model and hobby work a precise way to open small holes from 0.3 mm up to 0.8 mm. The range covers 0.3, 0.4, 0.5, 0.6 and 0.8 mm, which helps when a build calls for closely stepped diameters rather than one broad jump between sizes. The slim metal bits are suited to detail-focused tasks where larger workshop drills would be too coarse. Small diameter changes matter when preparing openings for pins, wire, rods or other fine components, and this set keeps those increments close at hand. The spiral cutting sections are made for careful drilling on miniature parts, while the fold-open case stores each bit in its own place instead of letting the sizes mix loose on the bench. That layout also makes it easier to return each bit after use and pick the next diameter quickly. On a modelling desk, the set fits naturally beside cutters, files and sanding tools for bodywork, cockpit details, scratchbuilding or electronics-related hobby tasks. The compact case travels neatly to club meets or workshop sessions, and the grouped size selection supports steady, methodical progress when a project needs more than one hole diameter.  Warning! Not suitable for children under 14 years.

Model-making tools

Fine Engraving Blade 0.15mm, modeling tool

€33.49

The Fine Engraving Blade 0.15mm is a precision modeling tool for adding or sharpening engraved detail on plastic parts. Its tungsten carbide construction is designed for smooth, consistent scoring, making fine panel lines and custom surface work easier to control during advanced finishing tasks. The 0.15 mm blade thickness suits narrow engraved lines, while the 25 mm total length and 2 mm shank match dedicated tool setups for stable handling. Recommended compatibility includes the Engraving Blade Holder 74139, plus Fine Pin Vise D 74050 and D-R 74112. The working method is straightforward: hold the blade at a 45° to 60° angle, then pull lightly across the plastic surface and repeat as needed to deepen the line with a clearly defined result. A color mark on the shank helps identify the thickness quickly when several blade sizes are kept together. For bench work focused on panel lines, hatches, access covers or custom scribed detail, this blade supports careful, repeatable passes instead of heavy pressure. The included storage case holds up to 10 blades, keeping matching sizes close at hand during longer modeling sessions.  Warning! Not suitable for children under 14 years.

Model-making tools

Fine Engraving Blade 0.1mm, hobby tool blade

€33.99

The Fine Engraving Blade 0.1mm is a precision hobby tool blade for adding sharply defined surface detail to plastic models. Made from tungsten carbide, it is designed for advanced engraving work such as refining panel lines or cutting new fine grooves, with a slim 0.1 mm profile that supports exact, narrow scoring. The blade measures 25 mm in total length and uses a 2 mm shank diameter for use with dedicated holders and compatible pin vises. For operation, the blade is held at a 45 to 60 degree angle and pulled lightly across the surface, then passed again as needed to deepen the line gradually. This pull action helps create a cleaner result than forcing a deep cut in one pass. A color-coded marking on the shank identifies the blade thickness quickly when several sizes are kept on the bench. Each blade comes in a storage case that holds up to 10 blades, keeping replacements together between sessions. It suits careful detailing on body panels, access hatches and other recessed lines where a narrow, controlled cut gives the surface a more defined scale look. Recommended holders are available separately.  Warning! Not suitable for children under 14 years.

Model-making tools

Fine Engraving Blade 0.25mm, hobby tool blade

€32.99

The Fine Engraving Blade 0.25mm is a precision hobby tool blade for scoring narrow lines and sharply defined surface detail on model parts. Held at a 45 to 60 degree angle and pulled lightly across the surface, it cuts a controlled scribed line that can be deepened gradually with repeated passes. Its 25 mm total length and 2 mm shank diameter suit compact hand-tool setups where close control matters. A color-coded marking on the shank identifies the blade thickness quickly, which helps when several engraving sizes are kept on the bench for different line widths. The blade is recommended for use with the dedicated Engraving Blade Holder and is also compatible with Fine Pin Vise D and Fine Pin Vise D-R. One blade is supplied. The included case stores up to 10 blades, making it easier to keep replacements together and ready for the next detailing session. On aircraft, cars, armor or sci-fi subjects, the narrow 0.25 mm profile supports clean recessed lines, refined hatch outlines and sharper separation between adjacent surface sections.

Model-making tools

Fine Engraving Blade 0.2mm, craft tool blade

€32.99

The Fine Engraving Blade 0.2mm is a precision craft tool blade for adding narrow engraved lines to plastic model surfaces. Made from tungsten carbide, it combines a very fine 0.2 mm blade thickness with a 25 mm overall length and a 2 mm shank, creating a compact format suited to controlled hand work on small details. This blade is used by inserting it into a compatible engraving blade holder or pin vise, then drawing it lightly across the surface in several passes to cut a clean groove. The documented use method focuses on a pull stroke rather than pushing down with force, which helps avoid raised edges, distortion, or blade bite in the material. A colour mark on the shank identifies the thickness, so this 0.2 mm version can be separated quickly from 0.1 mm, 0.3 mm, and 0.5 mm blades in the same range. An engraving blade holder is sold separately. On model parts, templates, and panel line work, the narrow profile supports crisp scribing where broader blades would remove too much material. The included case stores up to 10 blades, keeping spare and in-use blades together between work sessions. Protective goggles are recommended during use, as plastic shavings can form while engraving.  Warning! Not suitable for children under 14 years.

Model-making tools

Fine Engraving Blade 0.3mm, hobby tool blade

€32.99

The Fine Engraving Blade 0.3mm is a precision hobby tool blade for adding sharper panel lines and custom surface detail to scale models. Made from tungsten carbide, it is designed for smooth, consistent scoring when held at a 45 to 60 degree angle and drawn lightly across the surface in repeated passes. Its 25 mm total length and 2 mm shank diameter suit the dedicated Engraving Blade Holder and also fit Fine Pin Vise D and Fine Pin Vise D-R. The 0.3 mm thickness gives a defined line width for visible detail work without moving into broader cuts. A color-coded marking on the shank helps identify the blade thickness quickly when several sizes are kept together. Each blade comes in a storage case that holds up to 10 blades, keeping replacements and used blades organized between sessions. This blade suits advanced model finishing tasks such as deepening panel lines before paint, refining molded detail, or adding new engraved features to body shells and other model surfaces. Light repeated pulls across the material allow gradual control over depth and line definition, which is especially useful when working on visible exterior sections where clean edges matter.  Warning! Not suitable for children under 14 years.

Model-making tools

Fine Engraving Blade 0.4mm, hobby tool

€32.49

The Fine Engraving Blade 0.4mm is a precision hobby tool for adding sharper surface detail to plastic models. Its tungsten carbide construction is designed for engraving panel lines and custom scribed features with a smooth, consistent finish, giving shells, fuselages and body panels cleaner definition under paint and weathering. This blade measures 25 mm in total length and uses a 2 mm shank, a format intended for controlled detail work with compatible holders. Recommended use is with the dedicated Engraving Blade Holder 74139, and it is also compatible with Fine Pin Vise D 74050 and D-R 74112. For use, the blade is held at a 45 to 60 degree angle and pulled lightly across the surface to score it, with repeated light passes used to build a clearly defined line. A color-coded marking on the shank identifies the blade thickness quickly when several sizes are kept on the bench. The supplied case stores up to 10 blades, which helps keep matching sizes together between projects and supports a tidier setup for ongoing model detailing. This 0.4 mm version suits builders who want to emphasize existing lines or cut new recessed detail with a clearly controlled width.  Warning! Not suitable for children under 14 years.

Model-making tools

Fine Engraving Blade 0.5mm, hobby tool blade

€33.49

The Fine Engraving Blade 0.5mm is a precision hobby tool blade for adding sharper definition to model surfaces. Made from tungsten carbide, it is designed for engraving panel lines and cutting custom detail with a smooth, consistent finish that suits advanced model work. The 0.5 mm blade thickness gives a broader engraved line than finer variants in the same range, while the 25 mm total length and 2 mm shank diameter keep the format compact for controlled handling. It is recommended for use with the dedicated Engraving Blade Holder 74139 and is also compatible with Fine Pin Vise D 74050 and D-R 74112. The shank carries a color-coded marking so the thickness can be identified quickly when several blade sizes are kept together. Each blade comes in a storage case that can hold up to 10 blades. For use, the blade is held at a 45 to 60 degree angle and pulled lightly across the surface to score it. Repeated light passes help build a clearly defined line on plastic model parts, whether refining existing panel detail or adding new engraved features to a custom build.  Warning! Not suitable for children under 14 years.

Model-making tools

Fine Engraving Needle 20°, modeling tool

€23.49

The Fine Engraving Needle 20° is a precision modeling tool for clean, controlled scribing on curved and straight surface details. Its pointed needle tip differs from the hooked profile used on engraving blades, so it can trace arcs, corners and fine panel lines with a lighter, more exact feel on model parts. Crafted from cemented carbide and finished to a precise standard, the needle combines a 25 mm total length with a 2 mm shank for stable mounting in compatible holders. The working method is simple and exact: insert the needle carefully, hold it at the shown angle, then pull it lightly across the surface in repeated passes to score a clearly defined line. This approach helps avoid rough edges that can come from forcing a single deep cut. The needle is recommended for the Engraving Blade Holder 74139 and is also compatible with Fine Pin Vise D 74050 and D-R 74112. On the workbench, it suits tasks such as emphasizing existing panel lines, adding new engraved detail and refining curved shapes on plastic model surfaces. A protective case is included for storage and can hold up to 10 needles as well as separately sold engraving blades, keeping small precision tools together between detailing sessions.  Warning! Not suitable for children under 14 years.

Model-making abrasive material

Fine Lapping Film #3000, polishing film, 3 sheets

€9.99

Fine Lapping Film #3000 is a finishing supply for surface work on model parts, using polyester film coated evenly with fine abrasive particles to reduce blemishes and leave a smooth, consistent finish. The #3000 grade is suited to careful polishing stages where control matters, especially on clear parts, painted sections, and small areas that benefit from a flat, flexible sheet rather than a bulkier abrasive block. The uniformly coated surface helps maintain an even contact pattern during polishing, which is useful when refining plastic and metal components without concentrating abrasion in one spot. As a thin film format, each sheet is easy to position on narrow edges, curved sections, and detailed areas where precision matters. The material can also be used for wet sanding, adding another working method for controlled surface refinement during paint preparation or final finishing. With 3 sheets in the pack, the film fits neatly into repeated bench use, whether the task is cleaning up minor surface marks, improving clarity on transparent parts, or speeding up polishing on painted components. It suits hobby workflows that move step by step through preparation, correction, and final surface refinement.  Warning! Not suitable for children under 14 years.

Model-making abrasive material

Fine Lapping Film #8000, sanding film, 3 sheets

€10.49

Fine Lapping Film #8000 brings an extra-fine abrasive step to paint finishing, helping model builders smooth rough surfaces, seams and joints before the final polish. The 3 pink sheets measure 93 x 228 mm each and offer a thin, flexible format that can be cut or handled to suit broad panels as well as smaller sections on scale builds. Each sheet is uniformly covered with fine abrasive particles, which supports an even contact pattern during sanding and helps avoid patchy results on painted areas. The #8000 grade is positioned as a pre-treatment for compound polishing, making it a useful stage when working toward a glossy surface finish. Wet sanding compatibility adds another practical option, especially when a controlled, refined surface correction is needed on delicate paintwork. On the workbench, the film suits finishing passes on body panels, cleanup around joints, and surface preparation before compound use. It fits naturally into model painting routines where a smoother base and a more consistent sheen matter across the final finish.

Model-making tools

Fine Pin Vise D, hand drill, 0.1-3.2 mm chuck

€23.99

Fine Pin Vise D is a manual hand drill for model assembly tasks that call for clean, controlled holes in different diameters. Its chuck accepts drill bits from 0.1 mm to 3.2 mm, giving one compact tool the range to handle very small openings as well as larger pilot holes. The metal body, slim profile and precision tip suit close work on parts where powered drilling would be too aggressive. The long knurled handle gives the fingers a secure hold while the tool is turned by hand, and the hexagonal top cap provides a steady contact point for guided rotation. That layout helps when starting a hole exactly on a marked spot, opening mounting points, or adjusting fit on detailed assemblies. Because the drilling action is manual, the bit can be advanced gradually with close control over pressure and direction. This makes the tool useful for careful work on model parts, conversion tasks and other fine hobby jobs that depend on accuracy rather than speed. On the workbench, Fine Pin Vise D fits naturally alongside drill bits used for plastic kits, scratch-building and detail modification. It supports measured, step-by-step drilling where neat edges and exact placement matter most.  Warning! Not suitable for children under 14 years.

Model-making tools

Fine Pin Vise D-R, hobby drill, 0.1-3.2 mm

€24.49

The Fine Pin Vise D-R is a hand-held hobby drill made for precision hole work in scale model projects. Its 0.1 mm to 3.2 mm bit capacity covers delicate openings for fine detailing as well as broader drilling tasks used during model modification, giving steady manual control where small parts call for a lighter touch. The body is made from nickel-plated brass, combining a clean metallic finish with the weight and feel needed for accurate handling. An elastomer grip sits at the center to support a secure hold during slow, careful turns. At the rear, the rotating grip end uses built-in ball bearings, so the cap moves smoothly against the hand while the tool turns. This mechanism helps keep pressure consistent and the drilling motion controlled when working on narrow contact points or marked pilot positions. On the bench, the Fine Pin Vise D-R suits jobs such as opening mounting points, refining detail areas, or preparing parts for custom changes on scale models. The metallic sticker marked PIN VISE and the engraved rubber grip add clear workshop identity while the compact manual format stays focused on close, accurate work.  Warning! Not suitable for children under 14 years.

Model-making tools

Fine Pin Vise, hand drill for 0.1-1.0 mm bits

€14.79

The Fine Pin Vise brings measured hand control to drilling jobs that appear throughout model assembly, especially when small parts need a clean opening without the force of a powered tool. Its 0.1 mm to 1.0 mm bit range suits very fine work, from starting pilot holes to opening marked points in miniature components. The tool uses a compact metal construction with a black body, a textured center section and a silver front chuck. The knurled grip improves purchase during slow rotation by hand, while the chuck is shaped to hold micro drill bits used in detailed hobby tasks. A hexagonal swivel cap at the rear provides a firm resting point, allowing steady forward pressure while the fingers turn the body. This layout supports careful alignment when working on narrow surfaces, small panels or parts that need exact placement. On the bench, the Fine Pin Vise fits the rhythm of precise build work such as preparing openings before fitting detail parts or refining holes after test placement. It also suits craft and miniature projects where a hand-driven tool gives closer feedback than a motorized drill. Batteries are not required.

Model-making tools

Fine Pivot Bit 0.2mm, drill bit, 1mm shank

€7.99

The Fine Pivot Bit 0.2mm Shank 1mm is built for precise hole drilling in small-scale model work, where a very fine cutting diameter and steady handling are essential. Its 0.2 mm bit size targets delicate drilling tasks, while the 1 mm shank gives the tool a secure fit in compatible hand vises. The pivot drill bit design uses a bit section that is thinner than the shank. This construction helps reduce deviation at the drilling point and supports more accurate placement when working on fine parts. The material is described as shatter-resistant, giving the bit added resilience during careful manual drilling. A high-quality bit finish further supports clean results, especially when accuracy matters more than speed. This bit suits detailed workshop tasks such as opening tiny guide holes, refining model components or preparing parts that need exact alignment. It is compatible with the 74050 Pin Vise D, 74051 Pin Vise S and 74112 Pin Vise D-R, fitting neatly into established hand-tool setups for controlled hobby work.

Model-making tools

Fine Pivot Bit 0.6mm Shank 1mm, drill bit

€5.59

The Fine Pivot Bit 0.6mm Shank 1mm is made for detailed modeling work where hole placement and clean results matter. Its 0.6 mm bit is thinner than the 1 mm shank, a pivot-drill layout that helps reduce deviation during drilling while giving the bit greater resistance against shattering. That combination suits small, exact openings in parts that need a controlled start and a neat finish. The high-quality bit finish supports excellent hole quality, which is especially useful when refining components for scale builds or adding precise openings to scratch-built sections. The bit can be used on plastic, metal, brass and wood, making it a practical choice for mixed-material bench work instead of a single-surface specialist. A plastic storage case is included to keep the bit protected between sessions and easier to sort with other workshop tools. Compatibility with Pin Vise D 74050 and Pin Vise D-R 74112 gives this bit a clear place in a hand-tool setup for careful drilling tasks. On a workbench, it suits measured marking, slow hand rotation and close control when a standard bit would be too thick for the job.  Warning! Not suitable for children under 14 years.

Model-making tools

Fine Pivot Bit 0.7mm Shank 1mm, drill bit

€5.59

The Fine Pivot Bit 0.7mm Shank 1mm is built for detailed drilling work where a clean, controlled opening matters. Its pivot construction uses a 0.7 mm bit with a thicker 1 mm shank, a layout that supports precise hole placement while helping reduce deviation during delicate modelling tasks. The thinner cutting section handles fine openings, while the stronger shank adds resistance against shattering under careful hand or tool use. A high-quality bit finish supports clean hole quality, which is especially useful when preparing parts for added detail or refining small openings in model components. The bit can be used on plastic, metal, brass and wood, making it a practical choice for different stages of bench work across mixed-material projects. A plastic storage case is included to keep the bit protected between sessions and easier to sort with other workshop tools. On the workbench, it suits jobs such as opening pilot holes, refining marked drill points and handling small-scale detailing where a 0.7 mm diameter is required.  Warning! Not suitable for children under 14 years.

Model-making tools

Fine Pivot Bit 0.8mm, drill bit, 1.5mm shank

€5.59

This Fine Pivot Bit combines a 0.8 mm drilling tip with a 1.5 mm shank to support precise hole work on small model components. The pivot format uses a bit section that is thinner than the shank, which helps keep the drill running with less deviation while adding resistance against shattering during careful hand drilling. The 6.0 mm flute length gives space for controlled cutting, and the recommended hole depth of 5.5 mm helps match the bit to fine-detail tasks where depth matters as much as diameter. The finished surface of the bit is designed for excellent hole quality, which is useful when parts need a clean opening for pins, wire routes or detail additions. Use extends across plastic, metal, brass and wood, making this a practical choice for mixed-material bench work. A plastic storage case is included for keeping the bit protected between sessions. Compatibility with Pin Vise D 74050 and Pin Vise D-R 74112 makes the bit easy to place into established hand-tool setups. On the workbench, it suits measured drilling in compact spaces, whether opening starter holes in styrene, refining brass details or adding neat openings to wooden parts.  Warning! Not suitable for children under 14 years.

Model-making tools

Fine Pivot Bit 0.9mm, drill bit, 1.5mm shank

€5.59

This Fine Pivot Bit combines a 0.9 mm bit with a 1.5 mm shank to support precise hole drilling in detailed model work. The pivot design uses a bit section that is thinner than the shank, which increases resistance against shattering and helps reduce deviation while drilling by hand. A 6.0 mm flute length gives the cutting section a compact working area for controlled entry, and the recommended hole depth of 5.5 mm helps match the bit to small, exact tasks. The high-quality finish supports clean hole quality, which matters when opening mounting points, preparing detail holes or refining parts that need accurate alignment. The bit can be used on plastic, metal, brass and wood, making it useful across different stages of model building and workshop preparation. Each size comes with a storage case for keeping the bit protected between sessions. Compatibility with Pin Vise D and Pin Vise D-R makes it easy to pair with established hand-drilling setups for bench work, part modification and careful finishing on scale projects.  Warning! Not suitable for children under 14 years.

Model-making tools

Fine Pivot Bit 1.1mm, drill bit for precise holes

€5.59

The Fine Pivot Bit 1.1 mm with a 1.5 mm shank is made for controlled, accurate drilling in detailed hobby and model work. Its pivot design uses a bit section that is thinner than the shank, a construction that increases resistance against shattering and helps keep the drill path from wandering as the hole starts. This bit extends the Fine Pivot range beyond the existing 0.2 to 1.0 mm sizes, adding a larger option for jobs that still call for a slim, precise cutting point. The bit size is marked directly on the tool for quick recognition during bench work, which helps when several diameters are kept close at hand. A high-quality finish supports clean hole quality, especially where neat openings matter for pins, rods or added detailing. The bit can be used on plastic, metal, brass and wood, giving one tool a place across several stages of a build. Each size comes with a storage case for keeping the bit protected between sessions. Compatibility with Pin Vise D and Pin Vise D-R makes it easy to add this 1.1 mm size to an existing hand-drilling setup for careful workshop tasks and fine adjustment work.  Warning! Not suitable for children under 14 years.

Model-making tools

Fine Pivot Bit 1.2mm, drill bit for pin vise

€5.59

The Fine Pivot Bit 1.2mm Shank1.5mm is made for precise drilling work where clean placement matters. Its 1.2 mm bit is thinner than the 1.5 mm shank, a pivot design that gives the working tip added support and helps keep the drill line steady during careful hand use. This geometry is intended to reduce shattering and decrease deviation, which is especially useful when opening exact holes in model parts and detail components. The bit is marked with its size for quick recognition on the bench, so it can be picked out easily when several diameters are in use. A high-quality finish supports neat hole edges across different tasks. The bit can be used on plastic, metal, brass and wood, covering common materials found in scale modelling, scratch-building and modification work. Each size comes with a plastic storage case for straightforward organisation between sessions. The bit also complements existing Fine Pivot Bit sizes from 0.2 mm to 1.0 mm, making it a practical addition when a 1.2 mm diameter is needed for larger openings or specific fitting points. Compatible with Pin Vise D and Pin Vise D-R.  Warning! Not suitable for children under 14 years.

Model-making abrasive material

Finishing Abrasives Fine Set, model sanding sheets

€5.99

The Finishing Abrasives Fine Set brings 5 sanding sheets into model work where surface correction, smoothing and preparation need controlled grit steps rather than a single coarse pass. With 400, 600 and 1000 grades in one pack, the set supports gradual refinement on parts that need shaping first and a cleaner finish afterward. The sheet mix includes 2 pieces of 400 grit, 1 piece of 600 grit and 2 pieces of 1000 grit, giving a practical spread for workshop tasks around body shells, detail parts and scratch-built sections. The abrasive can be used on metal, wood and model materials such as ABS or styrene, which makes the set useful across different stages of a build or modification. Wet sanding helps carry away residue during finer finishing, while dry use suits quick corrections and edge work at the bench. The clog-resistant surface helps the abrasive keep cutting more consistently through repeated use. On a build table, the finer 1000 grit sheets suit final smoothing before paint-related steps, while 400 and 600 grit grades handle earlier correction and blending work. The flat sheet format stores easily with other workshop supplies and can be brought out whenever seams, edges or filled areas need a more even surface.  Warning! Not suitable for children under 14 years.

Model-making abrasive material

Finishing Abrasives Mid., sanding sheets, 5-pack

€4.99

Finishing Abrasives Mid. brings 5 sanding sheets into the workshop for modification and finishing work on model surfaces. The pack combines 180 grit, 240 grit and 320 grit grades, so heavier correction, intermediate smoothing and finer surface preparation can be handled with one set while parts move from shaping to paint-ready refinement. Each sheet measures 180 in the listed format and is intended for use on metal, ABS and wood. The mixed grit layout gives 2 sheets of 180, 1 sheet of 240 and 2 sheets of 320, which helps match the abrasive cut to the task instead of forcing one grade across every step. Wet or dry use changes the working method to suit dust control, surface feel or the material being refined. The clog-resistant abrasive surface keeps contact more even during repeated sanding passes, which is especially useful when cleaning seams, adjusting edges or refining filled areas on scale builds. On the bench, the coarser sheets can be used to correct joins and reshape small sections, while the finer grades help prepare panels, body parts or wooden components for the next coat or finishing stage. The format also suits keeping several grit levels close at hand during one build session, so surface correction and final smoothing can follow in a clear sequence.  Warning! Not suitable for children under 14 years.

Model-making abrasive material

Finishing Abrasives P1000, sanding sheets

€3.49

Finishing Abrasives P1000 brings controlled surface refinement to model building and modification work. The 3-sheet pack is intended for finishing tasks on Tamiya builds, where a fine abrasive grade helps even out transitions, tidy edges and prepare parts for the next stage at the workbench. The P1000 grade suits detail-focused sanding where a coarser sheet would remove too much material. Each sheet can be used on metal, ABS and wood, which makes the pack useful across mixed-material projects such as body parts, structural sections and scratch-built additions. Wet or dry application gives flexibility in how the abrasive is handled during different stages of shaping and finishing. The clog-resistant surface helps maintain a more even cut while working across flat sections, corners and smaller contact points. At the bench, the sheets fit naturally into repair, conversion and paint-prep routines, whether smoothing filler, refining joins or cleaning up modified parts before the next coat. The compact 3-sheet format also makes it easy to keep a fresh abrasive grade ready alongside knives, files and putty during ongoing model work.  Warning! Not suitable for children under 14 years.

Model-making abrasive material

Finishing Abrasives P1200, sanding sheets

€3.89

Finishing Abrasives P1200 brings controlled, fine sanding to model making and detail work, with a grit grade suited to refining surfaces before the next finishing step. The sheets are made for modification and finishing tasks on Tamiya builds, where clean transitions and even surfaces matter across small parts and visible sections. The abrasive can be used on metal, plastic and wood, which makes it useful across mixed-material projects without changing to a different sheet for each surface. Wet or dry application allows the sanding method to match the task, whether a damp pass is preferred while smoothing a painted area or a dry pass suits quick correction work on edges and joins. The clog-resistant surface helps the abrasive keep cutting more evenly during repeated strokes, especially when working on filler, coatings or fine surface irregularities. The pack contains 3 sheets, giving material for repeated finishing sessions or separate use across different stages of a build. At the workbench, P1200 grit suits the point where shaping gives way to refinement, such as smoothing a seam after adjustment, evening out a repaired section or preparing a surface for further coating. It also fits small, careful corrections on parts that need a lighter touch than coarse abrasives can provide.  Warning! Not suitable for children under 14 years.

Model-making abrasive material

Finishing Abrasives P1500, sanding sheets

€3.89

Finishing Abrasives P1500 brings a fine sanding grade to modification and finishing work on model parts, with 3 sheets sized for repeated use across shaping, cleanup and paint preparation. The P1500 surface is intended for refining rather than heavy removal, making it useful where a smoother finish is needed before the next step on metal, ABS or wood. The sheets can be used wet or dry, so the sanding method can match the material and the stage of work. Wet use helps carry away residue during fine surface work, while dry use suits quick corrections during fitting or edge cleanup. The clog-resistant abrasive surface keeps the sheet working longer during repeated passes, which is especially useful when smoothing filled areas, blending transitions or preparing small sections for paint. The thin, flexible sheet format also makes it easier to follow flat faces, edges and gentle curves on model components. On the bench, this grade fits the later stages of body preparation, part refinement and finishing touches before colour coats or final assembly. It also suits small correction work between build steps, where a controlled abrasive surface is needed instead of a coarser cut. For model making, workshop touch-ups and careful surface preparation, these 3 P1500 sheets add a precise finishing material to the tool set.  Warning! Not suitable for children under 14 years.

Model-making abrasive material

Finishing Abrasives P2000, sanding sheets

€3.79

Finishing Abrasives P2000 brings controlled surface refinement to model work where the last sanding stages shape the final look. The fine P2000 grit is suited to modifying and finishing tasks on Tamiya builds, helping prepare surfaces for clean paint application and careful detail work. Each sheet can be used on metal, wood and model materials, which makes the set useful across different parts of a single build or across separate workshop projects. The abrasive can be used wet or dry, so the sanding method can be matched to the material and the stage of work. Its clog-resistant surface helps the abrasive keep cutting consistently during longer finishing sessions, especially when smoothing primer, refining filled areas or evening out small surface marks. With 3 sheets in the pack, the set fits naturally into regular bench use, whether the task is correcting a seam line on a body shell, softening an edge on a fabricated part or preparing a painted section for the next coat. The fine grade also suits careful touch-up work where a lighter abrasive action is needed than in earlier shaping steps.  Warning! Not suitable for children under 14 years.

Model-making abrasive material

Finishing Abrasives P400, sanding sheets, 3-pack

€2.89

Finishing Abrasives P400 brings controlled surface preparation to model building, repair and finishing work with a medium grit suited to refining parts before the next stage. The sheets are intended for modifying and finishing Tamiya ranges and can be used on metal, wood and plastic, making them useful across mixed-material builds on the workbench. The P400 grade is suited to smoothing joins, cleaning up adjusted edges and evening out surfaces after shaping or correction work. Wet or dry use allows the sanding method to match the task, with water helping manage sanding residue on delicate areas and dry use supporting quick bench work between assembly and paint preparation. The clog-resistant abrasive surface helps maintain cutting action through repeated passes, which is especially useful when working across seams, corners and small shaped sections. With 3 sheets in the pack, the set fits routine workshop use such as part cleanup, body preparation, scratchbuilt detail work and general finishing on hobby projects. It also works well as a bench staple for keeping different grit stages organised alongside fillers, primers and other modelling supplies.  Warning! Not suitable for children under 14 years.

Model-making abrasive material

Finishing Abrasives P600, sanding sheets

€2.89

Finishing Abrasives P600 brings controlled surface refinement to model making, with a grit grade suited to modification work and finishing passes on parts that need a smoother, more even surface before the next step. The sheets are intended for use when modifying and finishing Tamiya builds, where steady abrasion helps tidy transitions, soften small imperfections and prepare components for further treatment. The abrasive material works on metal, wood and synthetic surfaces, which makes the pack useful across different stages of a build and across mixed-material projects. P600 grit sits in a practical range for refining rather than heavy stock removal, making it a strong choice when seams, edges or worked areas need a more uniform surface. The sheets can be used wet or dry, allowing the sanding method to match the material and the task. A clog-resistant surface helps maintain cutting action through repeated use, which supports cleaner, more consistent finishing on detailed parts. On the bench, these sheets fit naturally into body preparation, part cleanup and final surface correction before painting or after adjustment work. The pack contains 3 sheets, giving a ready supply for repeated workshop use across multiple model projects.  Warning! Not suitable for children under 14 years.

Model-making abrasive material

Finishing Abrasives P800, sanding sheets 3-pack

€2.89

Finishing Abrasives P800 is a 3-pack of sanding sheets made for modification and finishing work on modelmaking projects. The P800 grit gives a fine abrasive grade suited to smoothing surfaces, refining transitions and preparing parts for later paint or detail steps. Each sheet is thin and flexible, which helps when working around edges, corners and shaped sections where rigid sanding tools can be less precise. The sheets are suitable for metal, plastic and wood, covering the main materials often found in scale builds and workshop repairs. Wet or dry use allows the sanding method to match the task: water can help control residue during careful finishing, while dry sanding suits quick corrections and general surface preparation. The clog-resistant surface supports more even abrasion during repeated passes, which helps maintain a steady finish on small components and narrow contact areas. On a workbench, these sheets fit naturally into body preparation, part cleanup and final surface refinement before painting or assembly. They also suit touch-up work on already built sections, where controlled abrasion matters more than heavy material removal.  Warning! Not suitable for children under 14 years.

Model-making abrasive material

Finishing Abrasives Ultra Fine Set, sanding sheets

€5.89

The Finishing Abrasives Ultra Fine Set brings 5 sanding sheets together for careful surface work on model builds and detail parts. With 1200, 1500 and 2000 grit grades in one pack, the set supports the later stages of shaping, smoothing and finish preparation where small surface marks and transitions need a lighter touch. The sheet mix includes 1x 1200 grit, 2x 1500 grit and 2x 2000 grit, giving a clear progression across very fine abrasive levels. These abrasives can be used on metal, wood and plastic, which makes the set useful across mixed-material model work rather than only one surface type. Wet or dry application allows the sanding method to match the task at hand, and the clog-resistant construction helps the abrasive surface stay usable during longer finishing sessions. On a workbench, the finer grades suit cleanup after filling, seam reduction, paint preparation and final surface refinement before the next coat or finishing step. The compact 5-sheet format also makes it easy to keep several grit options close at hand during careful modification work on scale models and accessories.  Warning! Not suitable for children under 14 years.

Model-making tools

Handy Craft Saw II, craft saw, 2 carbon steel blades

€12.49

Handy Craft Saw II brings fine-toothed cutting control to model modification, Mini 4WD work and woodcraft, with 2 carbon steel blades that cover both detailed trimming and broader cuts. The slightly thicker .35 mm blade format helps the saw stay truer in use, while the smooth finish supports cleaner edges on shaped parts and craft sections. The set contains 1 wide blade and 1 slim blade, each designed for a different cutting task rather than repeating the same profile. The wide blade measures 46 mm and gives more reach for straight trimming passes, while the slim 43 mm blade suits tighter areas where a narrower cutting line is useful. Both blades fit into the included grip, creating a compact hand tool that can be adapted to the material and the cut path. Carbon steel construction gives the blades the crisp tooth definition needed for careful hobby and craft work. On the bench, the saw suits jobs such as separating parts, opening slots, refining body sections or adjusting wood pieces with a hand-guided cut. In model and craft sessions where a powered tool would be too aggressive, the fine teeth and narrow blade profiles support slower, more deliberate shaping with clear visual control.  Warning! Not suitable for children under 14 years.

Model-making tools

HC File PRO/Half-Rd 5mm, hobby file, half-round

€34.99

The HC File PRO/Half-Rd 5mm is a precision hand tool for shaping and refining model materials with a slim 160 mm format and a half-round working profile. One side presents a flat filing surface while the opposite side follows a curved form, making it easier to work along straight edges, inside curves and narrow recesses with the same tool. Its double-cut pattern gives the teeth a clear, even bite, which helps remove material in a controlled way during adjustment and finishing work. The file is intended for hard materials such as metal, carbon fiber and FRP, and it also handles standard model parts where a finer fit or cleaner contour is needed. A chrome coating on the teeth helps prevent shavings from packing into the cut, so the working surface stays clearer through repeated passes. The black PVC grip has a non-slip finish, plus the twin star logo and white printed wording. At the workbench, this format suits trimming a tight corner, refining a curved opening or smoothing a shaped edge before the next build step. A plastic case is included for storage between sessions and helps keep the filing surface protected when the tool is not in use.  Warning! Not suitable for children under 14 years.

Model-making tools

HG Angled Tweezers, model tool, stainless steel

€18.99

HG Angled Tweezers bring precise control to model work where small plastic parts and narrow spaces demand a more exact grip. The stainless steel construction and angled tip shape support clean pickup, steady positioning and careful release, especially when fingers or broader tools block the view of the work area. This model tool is made for handling delicate components during assembly rather than for general household use. The angled profile approaches parts from the side, which helps when placing pieces near raised details, inside tighter sections or along edges that are awkward to reach with a straight tool. Precision-made tips transmit small hand movements directly into controlled placement, which matters when aligning lightweight parts before fixing them in place. The stainless steel build also suits repeated bench use around cutting mats, sprues and subassemblies. On the workbench, the tweezers fit naturally into tasks such as lifting trimmed parts from the mat, holding a component steady during test fitting or guiding a small piece into its final position on a scale model. For detailed assembly sessions, this focused shape keeps handling accurate and the contact point easy to judge.  Warning! Not suitable for children under 14 years.

Other accessories

HG II Rounded Flat Brush, medium paintbrush

€9.99

The HG II Rounded Flat Brush Medium PBT is a dedicated hobby paintbrush built for controlled coverage and clean handling during model painting. Its rounded flat brush shape combines the broader contact of a flat profile with a softer edge, helping paint settle across surfaces with more control than a sharply squared tip. PBT bristles give the brush its working character, supporting steady paint pickup and a consistent stroke across repeated passes. The medium size suits a wide range of bench tasks, from laying down base colour on larger sections to guiding paint along edges, raised details and shaped panels. Within the HG II tool range, this brush is positioned as a practical choice for careful finishing work where brush shape and bristle response matter as much as colour choice. The format also fits hobby routines that move between coverage and refinement without changing tools for every step. At the workbench, the brush suits model parts, figures and other detailed painted surfaces that call for measured, even application. It works well in sessions that alternate between broader areas and tighter sections, keeping the painting process focused and precise.  Warning! Not suitable for children under 14 years.

Model-making tools

HG RevAction Angled Tweezers, hobby tool

€22.49

HG RevAction Angled Tweezers combine a reversed operating mechanism with an angled tip to give fine-detail work a more controlled feel at the bench. Squeezing the handle opens the tips and releasing closes them, so the tool can keep hold of a small part while the hand focuses on guiding it into place in tight, crowded areas. The angled profile helps the tips approach recessed spots and narrow gaps from a clearer working angle. Stainless steel construction gives the tweezers a precise, tool-focused build, while vulcanized fiber grips add a distinct contact surface on the handle. This combination suits tasks that call for repeated pick-up, placement and adjustment of small components, especially where steady pressure matters more than constant pinching. On a model building table, the tweezers can assist with aligning tiny fittings, shifting delicate pieces into position or handling small detail parts during careful assembly. They also suit electronics and other precision hobby work where access is limited and controlled grip matters across longer sessions.  Warning! Not suitable for children under 14 years.

Model-making tools

HG RevAction straight Tweezers, craft tweezers

€22.49

The HG RevAction straight Tweezers use a reversed operating mechanism that changes how small parts are held during detailed hobby work. Squeezing the handle opens the tips, and releasing it closes them, so the tweezers keep hold of a component while the hand can stay more relaxed. This setup is especially useful when a part needs to be held in place for longer moments during model assembly or fine positioning. The straight tip keeps operation simple and direct, with a clear line of sight to the contact point when placing or adjusting small pieces. Stainless steel construction gives the tool a precise, clean-working structure for repeated detail tasks, while vulcanized fiber grips add a distinct handle surface where control matters most. The narrow form also helps when working around compact assemblies, where larger tools can block access or obscure the view of the part being handled. On a workbench, the tweezers suit tasks such as holding tiny components steady, positioning delicate detail parts, or keeping a piece aligned while another step is completed. In model building sessions that involve repeated pick-up and placement, the RevAction layout supports consistent handling with less interruption between movements.  Warning! Not suitable for children under 14 years.

Model-making tools

HG Straight Tweezers, craft tool, round tip

€18.49

The HG Straight Tweezers are a steel craft tool made for precise handling in model building and other detailed hobby work. Their straight form and rounded tip support careful pickup, placement and adjustment of small parts, especially where fingertips would cover the work area or make alignment harder. The slim tip profile helps reach confined spots between assembled sections, while the longer body keeps the hand slightly back from the working area for a clearer view. The steel build gives a consistent response during repeated use, whether holding a tiny component in place, shifting a detail by a fraction, or guiding a decal into position. A wide, flat handle section adds control during light pressure changes, which matters when working with delicate pieces that need steady, measured movement rather than force. On a modelling bench, these tweezers fit naturally into tasks such as placing fine detail parts, lifting small pieces from a tray, or making small corrections before adhesive sets. They also suit careful craft and electronics handling where accuracy, reach and a clean grip matter more than bulkier hand tools.  Warning! Not suitable for children under 14 years.

Model-making tools

HG Tweezer Grip Scissors, hobby scissors

€28.99

HG Tweezer Grip Scissors bring compact control to close modeling cuts with a push-together action that keeps the hand position clear of the working area. The stainless steel blades are short at about 12 mm, which helps place each cut with accuracy on small surfaces where larger scissors can feel obstructive. The mechanism follows the same grip principle used on the Mini 4WD Curved Scissors in Item 74151, using pressure on the grips to open and close the blades. At 115 mm in total length, the tool stays easy to guide around corners, edges and narrow sections. The blade shape and size suit trimming vacuum molded bodies, cutting decals, shaping stickers and preparing masking tape for paint lines. Stainless steel construction gives the cutting edges a clean, consistent feel across repeated hobby tasks. On a workbench beside a scale model, the compact format fits naturally into detail-focused steps such as body trimming, decal preparation and masking work before painting. Between sessions, the included cap covers the blade area for tidy storage in a drawer, case or toolbox.

Model-making tools

HG Tweezers Grip Tip, precision hobby tweezers

€28.99

The HG Tweezers Grip Tip is a precision stainless steel tool made for handling minute components during static model assembly and R/C model maintenance. Its pronged tip geometry is built to grip small shafts, wire and rounded parts with more control, bringing steadier handling to close, detailed work at the bench. Each tip combines 2 prongs with a central groove, a layout designed to reduce the chance of parts slipping out from the front or the sides while being lifted, aligned or removed. The documented grip examples are concrete: 3 mm diff balls and small-diameter shafts can be held securely, and the tool is suited to assembling and dismantling R/C model gear differential units. Defined grip thresholds add clarity in use, with shafts or wire held sideways from 1 mm diameter, rounded objects from 2 mm diameter, and shafts or wire held lengthways from 1.5 mm diameter. The stainless steel body uses SUS410 material. On a model bench, that means cleaner placement of tiny drivetrain parts, more controlled retrieval of narrow metal pieces, and steadier handling when a fingertip is too large for the space. The slim straight profile also helps when working between closely packed components where direct access is limited.  Warning! Not suitable for children under 14 years.

Model-making tools

Long Nose Pliers with Cutter for RC Kit Assembly

€29.99

Long Nose Pliers with Cutter bring precise control to RC kit construction, combining narrow jaws for close access with a built-in cutting edge for wire work at the bench. The tapered nose reaches confined points around small assemblies, helping with gripping, bending and positioning when fingers or broader pliers would block the view. The steel body is made for repeated hobby use, and the polished head pairs with black handles for a clear, workshop-focused layout. Serrated gripping sections near the center of the jaws help hold small parts more securely during adjustment, while the cutter is stated for brass or steel wire used in model and radio control work. This makes the tool useful across several common build stages, from preparing wire lengths to aligning compact components before fastening. On a model bench, the slim profile supports careful handling in crowded areas where accuracy matters more than force. During electronics-related tasks, the same shape helps guide wire ends, hold small fittings and make controlled cuts without switching between separate gripping and trimming tools.

Other accessories

Masking Fluid 20g, model supply, precision bottle

€7.89

Masking Fluid 20g adds a controlled way to cover small sections before paint is applied, especially on uneven or curved surfaces where straight masking tape can be awkward to place. The bottle uses a soft body and a pointed dispensing nozzle, making it easier to guide the fluid onto shaped details, edges and narrow areas with a steady hand. The 20 g format gives a practical amount for repeated use on model painting tasks without taking much space on the workbench. The liquid form suits sections that need a flexible masking layer rather than a cut strip, and the nozzle layout helps place the material exactly where coverage is needed. This makes it useful for painted borders, small clear parts, trim lines and other detailed zones that benefit from careful separation during finishing work. On aircraft, cars, figures or other scale subjects, the bottle can be kept close at hand for touch-up masking and detail preparation between paint stages. It fits naturally into hobby bench routines where shaped surfaces, fine contours and controlled application matter as much as the colour coat itself.  Warning! Not suitable for children under 14 years.

Model-making masking tapes

Masking Sticker (5), model masking sheets 240x180mm

€11.491 m² = €51.07

This pack of 5 Tamiya Masking Sticker sheets gives model and craft work a clean starting point for controlled paint application. Each sheet measures 240 x 180 mm, providing enough area to cut broad covers, narrow strips or shaped sections for specific zones on a surface. The flat sheet format suits jobs where ready-cut tape widths do not match the outline that needs to be covered. The masking sheets are intended for painting tasks on R/C models, static models and craft creations. Sections can be cut to follow body contours, panel shapes or small detail areas before paint is applied, helping keep neighbouring sections separate during multi-colour work. The plain yellow sheet form also makes it easy to plan cuts visually before lifting the chosen shape from the backing. For repeated layouts, several matching pieces can be prepared from the same 240 x 180 mm sheet. On model bodies, scale parts or general hobby surfaces, the sheets support custom masking where standard rolls may be less practical. They fit neatly into painting setups that call for sharp edges, blocked sections or individually shaped covers, whether the task is a single accent area or a more complex layered finish.  Warning! Not suitable for children under 14 years.

Model-making masking tapes

Masking Sticker, 240x180 mm, model craft sheets

€11.991 m² = €53.29

These masking sticker sheets bring clean coverage and measured cutting to painting work on R/C models, static models and craft creations. Each pack contains 5 sheets, and every sheet measures 240 x 180 mm, giving enough surface for broad masked sections as well as narrow strips cut to size. A printed grid runs across the sheet surface, making it easier to mark out straight lines, repeated widths and consistent shapes before the material is trimmed. That layout is useful when paint schemes call for parallel edges, evenly spaced sections or matched pieces across more than one part. The adhesive sheet format also supports selective coverage on curved or flat areas where only certain sections need to stay clear during painting. On a workbench, the sheets can be cut into long bands for body lines, smaller blocks for detail zones or custom shapes for one-off graphics on model parts and craft builds. The 240 x 180 mm size leaves room to plan several pieces from one sheet, while the 5-sheet pack keeps extra material ready for later colour stages, corrections or a second project.  Warning! Not suitable for children under 14 years.

Model-making masking tapes

Masking Tape Sheets, paint masking film 2-pack

€5.891 m² = €61.35

These masking tape sheets bring precise paint control to model finishing with 2 large 200 x 240 mm film sheets that can be marked, cut and applied exactly where a paint boundary needs to sit. The flat sheet format suits custom templates, from long straight separations to curved sections and angled shapes across body panels and other detailed surfaces. The film is intended for masking work in model making and supports sharp, clear paint lines even when a heavier paint application is used. A printed 1 mm grid version is mentioned for the sheet range, making measured cuts possible where that variant applies. For multi-colour paintwork such as camouflage patterns, the film can also be placed on surfaces that have already been painted, allowing layered colour planning without disturbing the coat underneath. After painting, the film lifts away without leaving residue on the masked area. In practical use, the sheets suit custom paint jobs, edge definition and one-off masking shapes that standard roll widths cannot match. Scope of delivery: 2x masking film.  Warning! Not suitable for children under 14 years.

Model-making masking tapes

Masking Tape with Plastic Sheeting, 550 mm

€12.99

This masking tape with pre-attached plastic sheeting combines edge definition and broad surface coverage in one roll. When unfolded, the clear sheeting reaches 550 mm width, making it suited to paint work that needs more than a narrow tape line, such as covering larger sections of R/C car bodies during spraying. The tape attaches securely to the surface being covered, helping protect adjacent areas from unwanted paint while keeping the masked line clean and sharply defined. The transparent sheeting extends that protection across a wider area without needing separate film and tape, which streamlines preparation before colour coats or detail work. With a total roll length of 10 m, the material supports repeated use across multiple painting sessions or longer continuous sections. In practical use, the roll can be unspooled along rooflines, side panels or other broad sections where overspray needs to stay contained. It also suits general model finishing tasks that call for a crisp paint boundary and quick coverage of nearby surfaces, then lifts away easily once the painted area is complete.  Warning! Not suitable for children under 14 years.

Model-making tools

Mini Bending Pliers for PE, hobby tool

€36.99

Mini Bending Pliers for PE bring controlled shaping to small photo-etched parts where no clear bending line is present. The flat metal tip grips delicate sections securely while helping protect the surface from scratches, so fine details can be adjusted with a cleaner finish during model work. The tool is designed for close, precise handling on etched metal parts that need careful alignment before fitting. Straight lines up to 15 mm can be bent at one time, which helps when working on narrow flanges, tabs and edge sections that benefit from an even fold. When a right-angle bend tends to spring back, the jaw shape supports the section during the bend and makes the angle easier to form without relying on special techniques. Comfortable grips add steadier hand pressure during repeated adjustments and detailed assembly sessions. On the workbench, the pliers suit tasks such as shaping cockpit details, brackets, covers or other fine add-on parts before they are attached to a model. The tool can also be used with other materials such as plastic, giving added utility for small-scale hobby and craft jobs that call for neat, accurate bends.  Warning! Not suitable for children under 14 years.

Model-making tools

Model Cleaning Brush Anti-Static, hobby tool

€28.49

The Model Cleaning Brush Anti-Static is a dedicated hobby tool for keeping display models clear of dust, shavings and light debris without crowding delicate surfaces. Its slim metallic handle carries a wide brush at one end and a capped mini brush at the other, giving model care a precise, compact format that sits neatly beside paints, cutters and finishing tools. The main brush uses long fibers to move around raised details, fine edges and fragile assemblies where a cloth or larger duster can catch. Static control is built into the fibers, helping reduce the charge that draws dust back onto freshly cleaned surfaces. The capped mini brush adds a second cleaning option for recessed sections, panel lines and other narrow areas that need a smaller contact point. This 2-way arrangement supports regular maintenance on scale models after building, painting or display. On a shelf, in a cabinet or at a workbench, the brush suits quick touch-ups before photography, after sanding, or during routine display care. It also works on other household objects where light dust settles into small details, with the cap helping keep the smaller brush protected between uses.  Warning! Not suitable for children under 14 years.

Model-making tools

Modeler Knife pro Narrowchisel, hobby blade set

€8.49

The Modeler Knife pro Narrowchisel is a replacement blade set for detailed trimming work in confined areas. With 5 narrow chisel blades at 0.55 mm thickness, the set supports controlled removal of small protrusions on flat surfaces where a broader edge can be harder to place cleanly. The slim stepped tip gives the blade a focused contact point for careful cleanup on molded parts. Its narrower format is specifically positioned below the already available 4 mm chisel blade in the range, which makes this version better suited to close-set ribs, recessed sections and other tight spaces on model components. The chisel shape is intended for shaving away excess material rather than piercing, so it lends itself to refining edges, leveling raised marks and tidying mold-related irregularities with measured pressure. The included storage case keeps the blades together between work sessions. On the bench, this blade set fits tasks such as cleaning flat molded panels, refining ribbed structures and removing small surface protrusions before painting or further assembly. It suits model-making workflows that call for a narrow metal edge with more reach into restricted sections than a wider chisel format.

Model-making tools

Modeler Knife Pro Scraper, hobby blade set, 0.5 mm

€8.49

The Modeler Knife Pro Scraper brings a dedicated scraping profile to model finishing work, with 2 blades shaped specifically for changing surface texture and reducing surface thickness in a gradual, controlled way. At 0.5 mm thick, each blade offers a defined edge geometry that suits careful refinement on parts where a standard cutting blade would remove material too abruptly. The scraper-shaped end is intended for pull strokes, drawing the blade toward the body to shave away a selected section of the surface. That motion helps keep adjustments deliberate when refining contours, easing down raised areas or preparing a part for a smoother transition into surrounding detail. Because the blade is built for scraping rather than slicing, it suits tasks where the goal is measured removal across a wider area instead of a cut line. The set format keeps a second matching blade ready for ongoing bench work or replacement. On the workbench, this tool fits naturally into detailing, correction and surface-prep stages between shaping, test fitting and final finishing. It can be used when a panel, edge or molded section needs gradual reduction, or when a plain surface calls for a changed texture before the next build step.

Model-making tools

Modeler Knife Pro Scriber, blade set, 0.4 mm

€8.49

The Modeler Knife Pro Scriber blade set brings fine 0.4 mm scoring to detailed model work, with 5 replacement blades sized for narrow lines and careful surface marking. Each blade is designed for pull-stroke use, so the cutting edge scores the material as it is drawn back, giving a controlled action for panel lines, trimming guides and measured cut paths. Its slim profile is thinner than the Plastic Scriber II Item 74091, which makes this version especially suited to precise, closely spaced detail where a broader groove would look heavy. The blade format also supports score-and-break work on plate material: mark the line, deepen the pass, then separate the section to the required size. That makes the set useful not only for surface engraving but also for shaping custom parts during scratchbuilding and modification work. The 5-piece pack keeps matching blades ready for repeated bench sessions, whether the task is refining engraved detail, preparing clean edges on sheet stock or cutting plate sections for a tailored fit. A storage case is shown in the product presentation for organized handling between uses.

Model-making tools

Modeler's Blade Pro chisel, replacement blades

€8.49

The Modeler's Blade Pro chisel replacement set keeps a precision bench tool ready for detailed surface work with 10 spare blades in one pack. Each blade is 0.55 mm thick, giving the edge a defined profile for controlled chiseling, engraving and cleanup on flat areas where excess material needs to be pared back carefully. The blade format suits tasks that call for a straight, deliberate pass rather than a pointed cut. Raised marks, small protrusions and uneven spots can be worked down with measured pressure, while engraved lines can be refined with a tool shape made for contact across a flat face. The 10-piece quantity supports longer project cycles across multiple builds, touch-ups or finishing sessions without interrupting the workflow when a fresh edge is needed. As replacement blades, they are a practical match for keeping the Modeler's Blade Pro in regular use on the workbench. During model preparation, body cleanup or detail correction, these blades fit naturally into the stages where surface accuracy matters most. They suit careful bench tasks such as refining panel areas, tidying molded excess and sharpening engraved detail before painting or final assembly.  Warning! Not suitable for children under 14 years.

Model-making tools

Modeler's Blade Pro Curved, replacement blades

€8.49

Modeler's Blade Pro Curved is a set of 3 replacement blades for fine hobby cutting where a shaped edge matters as much as a sharp point. Each metal blade combines a pointed tip, a curved cutting edge and an oval mounting slot, creating a format suited to careful trimming, guided slicing and close work on thin materials. At 0.45 mm thick, each blade is built for soft fabric materials such as film, cloth and Japanese paper. The curved profile helps the cutting edge track along arcs, corners and narrow outlines with a more natural motion than broad straight cuts. The pointed tip gives added control when starting a cut or reaching into small sections, while the mounting slot supports secure fitting in the matching handle system. The 3-piece pack keeps spare blades ready for ongoing bench work without interrupting a project. On a model making table, these blades suit jobs such as trimming covering film, shaping paper parts or refining cloth-based material with a lighter touch. They also fit craft setups where clean, accurate cuts matter across repeated detail tasks.  Warning! Not suitable for children under 14 years.

Model-making tools

Modeler's Blade Pro Straight, hobby knife blades

€8.49

Modeler's Blade Pro Straight brings a focused cutting format to detailed hobby work, with 5 straight replacement blades designed for exact trimming and careful edge work. The 0.5 mm blade thickness supports controlled handling in tight areas where small adjustments and clean lines matter. Each blade is shaped for precise, detailed tasks rather than broad cutting passes, which makes the set well suited to refining parts, cleaning edges and handling close work on model-making projects. The straight profile gives a clear cutting path for measured movements, while the replacement format keeps a fresh edge available across repeated bench sessions. A compact storage case keeps the blades together when not in use and helps separate unused blades from the one currently fitted. On the workbench, the set fits naturally into finishing steps that call for accuracy, whether trimming small sections, tidying cut lines or preparing parts for the next stage. The 5-piece count also makes it practical to keep spare blades ready for ongoing craft and model tasks where a sharp, consistent edge is part of the result.  Warning! Not suitable for children under 14 years.

Model-making tools

Modeler's Knife Blade Set, Replacement Blades

€6.49

The Modeler's knife blade set keeps a Modeler's Knife ready for precise cutting with 25 replacement blades stored in a compact plastic container. The pointed metal blade shape is suited to fine trimming work, where a clean edge and close control matter during modelling and craft tasks at the bench. Replacing a worn blade promptly helps maintain the knife's cutting performance and supports neater results on detailed work. The storage case keeps the blades gathered in one place between sessions, so the set stays organised in a drawer, toolbox or hobby area. The pack is focused on the working part that sees regular wear, making it a practical refill for repeated use rather than a one-off accessory. On model building projects, the spare blades are ready for careful trimming, shaping and detail work whenever the current edge starts to dull. In a craft or workshop setup, the container format also helps keep replacement blades together and easy to locate when steady, accurate cutting is needed again.

Model-making tools

Modeler's Knife Mint Green, model tool

€14.49

The Modeler's Knife Mint Green brings a clear, focused cutting tool to detailed hobby work, with a slim hand-held format that suits careful trimming, shaping and preparation on scale builds and craft projects. The mint green finish stands out on the workbench, making the knife easier to locate among cutting mats, sprues, paints and small components during concentrated sessions. Used for fine cutting tasks, this model tool helps create neat edges on masking material, decals and small build parts where accuracy matters. The narrow format supports controlled movement in tighter areas and along short cut lines, which is useful when refining details before painting or final assembly. Its role fits naturally into bench work that involves repeated small adjustments rather than broad cutting passes. The simple, dedicated design keeps the function clear: controlled trimming for model making and related hobby tasks. On a build table, the knife can be kept close at hand for shaping small sections, tidying edges and preparing surfaces between construction and finishing steps. It also fits craft setups where precise hand cutting is needed for detail-led work on compact materials and components.  Warning! Not suitable for children under 14 years.

Model-making tools

Modeler's Knife Pro, hobby knife, reinforced handle

€31.49

The Modeler's Knife Pro is built for controlled, detailed cutting, pairing a reinforced handle with a precise blade mount for careful work on hobby materials. The elastomer grip sits securely in the hand, while the metal chuck clamps the blade firmly for steady trimming, scoring and fine shaping at the bench. The set comes with 7 interchangeable blades in 3 profiles: 3 straight blades, 2 curved blades and 2 chisel blades. That mix supports different cutting actions, from long clean slices to shaped cuts around tighter lines and flat-edged trimming where a defined corner matters. A protective cap covers the knife when it is not in use, and a separate spare blade case stores the remaining blades together instead of leaving loose edges on the work surface. The black handle and gold-toned chuck give the tool a clear technical look that matches its workshop focus. On model kits, sheet materials or masking work, the different blade shapes allow close, deliberate cuts where scissors or larger cutters would be less exact. The compact format suits repeated bench use, whether separating small parts, refining edges or cleaning up detail before the next assembly step.  Warning! Not suitable for children under 14 years.

Model-making tools

Modeler's Knife, hobby craft knife with 25 blades

€13.99

Modeler's Knife brings precise control to plastic model construction with a medium-size format, a fine pointed blade and a 0.45 mm blade thickness suited to intricate cutting, curving and shaving. The slim profile helps guide the blade into narrow corners, along panel edges and across small surfaces where clean trimming matters. The black handle pairs with a textured metal grip section that supports steady hand placement during close detail work. Alongside the knife, the set contains 25 spare blades for continued use across repeated building sessions. A protective cap covers the blade between tasks, and the blade case keeps replacements together instead of loose on the bench. The presentation image also shows a dedicated handling tool attached to the case for blade management, adding order to routine blade changes. At the workbench, the knife suits jobs such as refining cut lines, shaving excess material from plastic parts and adjusting small details before final assembly. It also fits careful finishing passes where a pointed blade can follow tight contours more closely than broader cutting tools.

Model-making tools

Modeling Drill Chuck, hand tool, 1.5-6.5 mm

€38.99

The Modeling Drill Chuck is a hand-operated bench tool for controlled drilling when a normal pin vise is not enough and an electric drill would be too strong. Its blue handle gives a fuller grip in the hand, making it easier to apply steady turning force while keeping close control over small, precise movements at the work surface. At the front, the black chuck clamps drill bits from 1.5 mm to 6.5 mm, extending the working range beyond very fine pin-vise tasks. That wider capacity makes the tool useful for different drilling steps in model making, from starting larger openings to reworking holes that need a cleaner fit for parts or hardware. The manual format keeps the action direct: the handle is turned by hand, the chuck holds the bit, and the drilling pressure stays closely managed through each rotation. The ribbed section near the chuck also supports a secure hold while guiding the tool tip into place. On a hobby bench, this tool fits the moments that call for more force than a slim precision holder can provide, yet still reward a slower, more deliberate touch than a powered drill. It suits careful work on model assemblies, detail modifications and other fine workshop tasks where control at the bit matters as much as the hole itself.  Warning! Not suitable for children under 14 years.

Model-making tools

Modeling Flat Chisel Blade 2mm, hobby tool

€22.49

The Modeling Flat Chisel Blade 2mm is a precision hobby tool for finishing plastic model parts with a clean, controlled cut. Made from high-speed steel, it combines a 2 mm blade width, 2 mm shank diameter and 25 mm overall length in a compact format that reaches small surface details and tight working areas. This blade is intended for final removal work rather than heavy cutting. Thicker protrusions should be filed down first, then the blade can be drawn across the remaining material with the underside kept flush to the plastic surface. That low-angle scraping action helps shave away the last raised trace without digging deeply into the part. It is also suited to spots that are awkward to reach with a modelling knife or side cutters. A storage case is included for keeping the blade covered when not in use. The blade is compatible with Item 74139, the recommended holder, and with Item 74112. On the workbench, it fits naturally into detail-finishing steps such as refining seams, removing small imperfections and preparing surfaces for final abrasive cleanup. Protective goggles should be worn during use because plastic shavings may fly.  Warning! Not suitable for children under 14 years.

Model-making tools

Modeling Scissors for PE-Parts Craft Tool

€25.99

Modeling Scissors for PE-Parts bring close, controlled cutting to one of the most delicate stages of model finishing. The compact scissors use 1 cm blades that suit tiny photo-etched sections, making it easier to separate fine metal details cleanly when a standard knife feels less precise on small attachment points. Photo-etched parts in stainless metal can be trickier to handle than standard molded parts, so the tool focuses on the cutting step with a shape made for detailed bench work. The short blades place the cutting point near the fingertips, which helps with careful alignment on narrow tabs and small contours. The tool is intended for precision photo-etched part work and is not meant for thicker surfaces. A special cap is included to cover the blades when the scissors are stored between sessions. On a model bench, the scissors fit naturally into finishing tasks such as preparing grilles, brackets, panels or other fine etched details before filing or shaping. Used as the first step in a photo-etch workflow, they help keep small parts manageable and support a tidier path toward crisp scale detail.  Warning! Not suitable for children under 14 years.

Model-making tools

Modeling Template Round 1-12.5, scribing template

€9.59

Modeling Template Round 1-12.5 brings controlled circle scribing to model work with a photo-etched stainless steel fret and 3 removable template sheets. The round openings span 1 mm to 12.5 mm in 0.25 mm steps, so small inspection covers, larger access circles and repeated matching details can be laid out with a consistent diameter. The 0.1 mm stainless steel construction keeps the edge fine against the work surface, which helps the engraving needle track the inside of each circle cleanly. On convex parts such as aircraft fuselage sections, the sheets can be bent to follow the shape, with a minimum target component radius of 30 mm stated for curved surfaces. The templates are intended for scribing and engraving PS and ABS resin parts. The fret format also keeps the full size range together between tasks, while the removable sections let the chosen circle sit exactly where the marking is needed. On a bench, the set suits careful layout work before painting, weathering or panel accenting, and it also supports repeat detailing when several matching circles are needed on the same build. Light repeated passes with the needle produce the marked line gradually, giving steady control on flat panels and gently curved shells alike.  Warning! Not suitable for children under 14 years.

Model-making tools

Modeling Template RR 1-6, hobby scribing guide

€9.99

Modeling Template RR 1-6 brings rounded rectangle scribing into a controlled, repeatable format for detailed model work. The photo-etched stainless steel fret is designed for use with Tamiya engraving needle tools, letting fine lines follow a defined edge instead of relying on freehand marking across small surfaces. The fret contains 3 template sheets with rounded rectangle openings in multiple sizes, spanning 1 mm to 6 mm in width and 1.5 mm to 12 mm in length. That spread supports small access panels, vents, hatches and other surface details where matching proportions matter across more than one part. The smallest opening measures 1 mm x 1.5 mm, while the largest reaches 6 mm x 12 mm, so the same set covers both tight detailing and larger marked features. The 0.1 mm stainless steel construction keeps the edge fine while allowing the sheet to conform to shaped parts. On curved assemblies, the template can be bent against convex surfaces with a minimum target component radius of 30 mm, which makes it useful for aircraft fuselage sections and similarly rounded bodies. It is intended for scribing and engraving PS and ABS resin parts when paired with the matching needle tool, adding a precise guide to bench work focused on clean repeated shapes.  Warning! Not suitable for children under 14 years.

Model-making tools

Modeling Template Square 1-10, stencil set

€9.59

Modeling Template Square 1-10 brings repeatable square and rounded-square marking to detailed model work with a photo-etched stainless steel fret designed for fine scribing. The set supports clean layout of access panels, hatches and surface details by giving the engraving needle a precise edge to follow across sizes from 1 mm to 10 mm. The fret contains 4 separate template sheets, and each sheet covers the full size range in 0.5 mm increments. One sheet uses right-angle corners, while the other 3 apply R10%, R15% and R20% corner ratios for rounded-square shapes. That ratio system keeps the corner radius tied directly to the side length, so a 10 mm square at R10% produces 1 mm radius corners. The templates are made from 0.1 mm stainless steel, which helps them sit close to the surface while remaining flexible enough to bend over convex parts. The stated minimum target component radius is 30 mm. On aircraft fuselage pieces, vehicle panels or scratch-built surfaces, the thin metal sheets help transfer matching shapes again and again instead of drawing each line freehand. The graduated openings support both small maintenance-panel details and larger geometric markings, making the set a focused tool for precise, repeatable surface work in model building.

Model-making tools

Needle Nose Pliers with Cutter for Model Work

€39.99

These needle nose pliers combine a long, slim jaw shape with an integrated cutter, giving model work a precise hand tool for gripping, bending and trimming. The chromium-vanadium steel jaws reach into tight areas where broader pliers cannot, which helps when handling small parts on R/C projects, static models and other detailed hobby tasks. Their narrow profile also allows the tool to be used much like tweezers when a part needs a firm hold rather than fingertip contact. At the hinge, the cutting edges add a second workshop function without taking up extra bench space. They cut mild steel wire up to 1.2 mm diameter and brass wire up to 1.3 mm, covering common wire sizes used for detail work, adjustments and scratchbuilding. The long jaw form supports careful bends as well as straight gripping, so one tool can move from shaping wire to placing components in the same session. A twin star logo appears on the hinge joint. The PVC-coated handles provide a non-slip grip that supports controlled pressure during repeated use. On a workbench, beside an R/C chassis or over a partly finished static model, the slim tips help guide the tool exactly where the task is happening, whether that means holding a tiny part, bending brass wire or making a quick clean cut.

Other accessories

Non-Scratch Grips LNP II, model accessory, 2set

€3.19

Non-Scratch Grips LNP II is a model accessory set built around a clear functional detail: a non-scratch contact surface paired in a 2set format. That combination supports handling, replacement and setup tasks where grip is needed but finished parts should stay free from unwanted marks. The LNP II designation identifies this specific version rather than a generic grip, which matters when matching accessories to an existing model setup. With 2 matching pieces in the pack, the set suits applications that need a left and right pair or a direct spare kept ready for later maintenance. The accessory format also makes it easy to store alongside other workshop supplies for regular adjustment sessions. No battery-powered function is involved in the set itself, so the focus stays on the contact surface and the paired quantity. On a model bench, these grips fit naturally into routine replacement work, setup changes or careful handling of finished assemblies. They also suit parts boxes kept for ongoing maintenance, where an exact named version and a matched pair save time during future repairs or refresh work.  Warning! Not suitable for children under 14 years.

Model-making tools

Non-Scratch Long Nose Pliers II, hobby pliers

€22.99

Non-Scratch Long Nose Pliers II brings fine control to bench work where standard hand tools can feel too broad. The slim nose shape reaches into narrow gaps, helping with careful wire bends, small-part handling and close-up adjustment work during model making and hobby assembly. The jaw profile is designed for tasks that call for accuracy rather than force. Non-scratch contact surfaces support cleaner handling on delicate components, which is useful when working with soft metal details, shaped wire or finished fittings that need to stay neat while being held or positioned. The elongated nose also improves access around crowded subassemblies, letting the tool approach parts from tighter angles than shorter pliers. For repetitive bench tasks, that combination of reach and controlled grip helps keep movements measured and precise. On a worktable, these pliers fit naturally into build sessions that involve trimming, bending, test-fitting and part placement. They also suit repair and adjustment work on scale models, miniatures and other detailed hobby projects where small components need a steady hold and a lighter touch than general-purpose tools usually provide.  Warning! Not suitable for children under 14 years.

Model-making tools

Paint Stirrer Metal, paint tool, 2 stainless stirrers

€6.39

This paint tool set brings controlled colour mixing to bottled paints with 2 stainless steel stirrers, each measuring 15 cm. The slim format reaches into narrow paint jars, while the metal construction gives a firm, direct feel during mixing. At one end, a small spoon shape helps lift pigment and paint from the bottom of the bottle. The opposite flat spatula end supports blending, folding and working different shades together with a more even motion. The double-ended layout gives each stirrer 2 distinct working surfaces for different paint-handling tasks. The spoon tip suits settled colour and denser material near the base of the bottle, while the flat end can spread and combine paint more broadly during shade adjustment. Stainless steel also makes the set suitable for repeated workshop use where clean, precise handling matters. With 2 matching tools in the pack, one stirrer can stay with a current colour while the other is used for the next mix. On the bench, the set fits naturally into model painting, detail finishing and colour preparation before brush work. It also supports mixing custom tones in small quantities when several bottled paints are used in the same session.  Warning! Not suitable for children under 14 years.

Model-making tools

PhotoEtched 0.1 mm Saw Blade Set, craft saws

€13.49

The PhotoEtched 0.1 mm Saw Blade Set brings highly controlled cutting to detailed model work, using thin photo-etched metal saws to make extremely fine cuts in small sections and narrow spaces. The slim blade profile helps when a standard hobby blade would remove too much material or struggle to follow a tight line. Each saw features a grip section that can be folded over to increase support while handling the blade by hand. That added structure helps during careful trimming and scribing on PS and ABS resin parts, where a steady hold matters for clean edges and accurate line placement. The set includes 5 saws, giving several blades ready for repeated bench use. The sheet format also shows multiple blade profiles suited to different access angles and cut shapes. For more controlled bench work, the blades can also be fitted to the handle of the Modeler's Knife. This setup suits panel line work, slot cutting, careful separation of molded sections and other detail-focused shaping tasks on scale models. The saws are intended for PS and ABS resin parts and are not for use on metal or hard plastics.

Model-making tools

Plastic & Soft Metal Scissors, hobby tool

€29.99

Plastic & Soft Metal Scissors bring controlled cutting to model making, workshop prep and general craft tasks with anti-rust treated stainless steel blades and a compact 170 mm format. The 40 mm blade length supports close work on sheet materials, while the navy blue grip gives a clear, secure hold during repeated trimming passes. These scissors are designed to handle a broader range of materials than standard scissors. Cutting guidance covers Tamiya Pla-plate up to 1.2 mm, Tamiya Clear Pla-plate up to 0.5 mm, polycarbonate up to 1.0 mm and other plastics up to 1.0 mm. Softer metals are also within scope, including aluminum up to 0.5 mm and copper, brass or nickel up to 0.3 mm. Beyond model materials, the blades can also be used on leather and paper up to 2.0 mm, plus cardboard or rubber sheeting up to 5.0 mm. These figures are intended as a guideline for material choice and cut planning. On the bench, the narrow blades suit body shell trimming, sheet shaping and careful cut lines where bulky household scissors can get in the way. The broad material range also makes the tool useful for mixed-media hobby work, from preparing templates in paper to refining thin metal or plastic parts for custom builds.  Warning! Not suitable for children under 14 years.

Other accessories

Plastic Beam 3x3mm SquareTube, model supplies

€7.49

Plastic Beam 3x3mm SquareTube brings clean geometry to scratch-building and model modification, with a square 3 x 3 mm profile that supports straight runs, measured cuts and neatly aligned joins. The 5-piece pack gives builders matching stock for repeated structural work, detail fabrication or replacement sections where consistent dimensions matter. The square tube format is useful wherever a build needs crisp edges and a stable profile rather than a rounded rod. It can be cut to length, combined into frames, used as internal bracing or adapted for custom details on scale models and workshop projects. Because each beam shares the same section, layouts stay uniform across multiple contact points and parallel structures. The compact profile also suits confined spaces where larger stock would crowd surrounding parts. On a bench, these beams fit naturally into measured fabrication work, from reinforcing a body support to creating small structural inserts and straight-edged custom features. They also serve well in repair jobs where a damaged section needs replacement with matching square stock. Since batteries are not included, no battery-related function applies to this model supply.

Other accessories

Plastic Beam 5x5mm SquareTube, model supply

€7.49

Plastic Beam 5x5mm SquareTube brings a clean square profile to model building, with 5 x 5 mm dimensions that suit structural additions, fabricated frames and custom detailing. The pack contains 4 matching beams, giving consistent stock for repeated cuts and balanced left-right sections in scratch-built work. The square tube format offers straight edges and an even cross section that help when planning measured joins, supports and boxed shapes. In contrast to narrower strip material, this profile can define corners and framed sections with more visual presence. The identical beam size across all 4 pieces supports tidy geometry when a build calls for parallel members, repeated lengths or matching braces. The compact format also makes the material easy to combine with other model supplies in conversions, diorama structures or workshop modifications. On the bench, these beams suit careful trimming, test fitting and placement in areas where a hollow square section gives the right look or structure. They work well for custom projects that need clean lines, repeatable dimensions and a straightforward base for fabricated details in scale scenes or model assemblies.

Other accessories

Plastic Beam 8x8mm SquareTube, model supply

€7.49

This set of Plastic Beam SquareTube parts brings a clean 8 x 8 mm profile to scratch-building, structural detailing and custom model work. With 3 matching beams in the pack, it supports measured cuts, repeated sections and tidy alignment across frames, supports or fabricated add-ons where a square cross section is needed. The tube format opens up more than one use within a build. It can serve as a visible framework element, a hidden spacer, or a base for adapting other parts around a consistent shape. The plastic material is easy to integrate into many modelmaking workflows where straight edges, even dimensions and repeatable lengths matter. The 8 x 8 mm section also gives a clear reference when planning fit around body panels, scenery elements or workshop-style structures. On the bench, these beams suit custom projects, repairs and one-off conversions that call for simple geometry and clean lines. They also work well as stock material for keeping matching sections ready for later adjustments, replacement pieces or parallel fabrication tasks within the same modelmaking setup.  Warning! Not suitable for children under 14 years.

Model-making tools

Plastic Model File Flat 6mm, hobby hand tool

€23.49

This flat model file combines a narrow 6 mm working width with wave pattern teeth for controlled shaping and a clean surface finish on small parts. The tooth pattern is designed to keep shavings from clogging the filing face, so the cut stays consistent while seams, edges and formed sections are refined by hand. The conventional flat shape suits a wide range of model-making tasks where a broad abrasive block would reach too far. Its slim metal filing section can be guided along straight runs, pressed into tighter areas and used to level raised material with measured strokes. The long handle adds a steady grip for careful pressure control, which helps when adjusting fit, cleaning part lines or preparing surfaces for the next finishing step. On the workbench, this file fits naturally into plastic model building, detail correction and general hobby finishing. It can be used between trimming and final surface preparation, or kept close for repeated touch-ups as individual parts are shaped and checked during assembly.  Warning! Not suitable for children under 14 years.

Model-making tools

Plastic Scriber II, hobby tool with spare blades

€11.79

Plastic Scriber II is a dedicated hobby tool for scoring and cutting plastic sheets, with a hooked blade shape that supports controlled line work on model materials. On the workbench, that focused cutting action helps start clean guide lines for trimming, reshaping and other detailed modification tasks. Beyond sheet work, the tool is also intended for creating mold lines on model parts and for modifying Mini 4WD machines. The blade can be retracted after use, which keeps the edge covered when the tool is set down between steps or returned to storage. Two spare blades are stored inside the handle, so replacements stay with the tool instead of getting lost among other bench supplies. The handle itself keeps the core parts together in one compact format suited to repeated workshop use. During model preparation, Plastic Scriber II fits naturally into jobs such as marking cut paths, refining part surfaces and adjusting small sections that need a more exact line than a general craft knife can provide. It also suits bench setups where compact tools and stored spares help keep detailed work moving without breaking concentration.  Warning! Not suitable for children under 14 years.

Model-making tools

Plastic Soft Metal Side Cutter, craft tool

€38.49

This side cutter brings precise control to trimming work with angled jaws, a silver metal cutting head and black curved grips shaped for steady handling. The cutting action suits plastic parts and small soft metal pieces, making it a useful bench tool for model assembly, craft work and fine cleanup tasks. The jaw shape helps reach close to attachment points on sprues, pins and wire, so cuts can be placed with more accuracy where neat separation matters. The metal head keeps the cutting area clearly defined in view during detail work, which supports careful preparation before fitting, gluing or finishing. Curved grips give the hand a stable hold through repeated use, helping maintain even pressure across short, controlled cuts. This focused format suits hobby benches where small components, narrow spaces and tidy edges matter more than heavy-duty cutting force. On a model-building table, the side cutter supports clean part removal before sanding and fitting. In general craft use, it also handles fine wire and other soft metal pieces when shaping, shortening or preparing components for the next step.  Warning! Not suitable for children under 14 years.

Model-making tools

Precision Screwdriver (+) Static, model tool

€11.99

Precision Screwdriver (+) Static is a hand tool for model building and maintenance where small Phillips screws call for steady, direct control. The fixed manual format keeps the action simple at the workbench, whether fitting parts during assembly or making small adjustments on finished builds. Its focused design suits detailed hobby tasks better than broad household hardware work, because the tip is intended for the compact screw sizes commonly found in models and accessories. During assembly, the screwdriver helps guide careful turns in confined areas where larger handles or higher torque would be less suitable. It also fits routine upkeep, such as retightening small fittings after handling or transport. The manual, non-powered format keeps feedback immediate through each turn, which is useful when working close to painted surfaces, small brackets or narrow mounting points. On a build table, it supports measured progress across repeated fastening steps without adding extra complexity to the setup. It also earns a place in a regular hobby toolkit for adjustment sessions, replacement work and general bench maintenance around scale projects.  Warning! Not suitable for children under 14 years.

Model-making tools

Quick Hose Joint Airbrush Connector Type-S PF-1/8

€26.49

The Quick Hose Joint streamlines airbrush setup by placing a quick-connect fitting between the airbrush and hose. A single-touch action replaces repeated screwing and unscrewing, which is especially useful when more than 1 airbrush is used during the same painting session. The metal connector parts shown in the set focus on fast tool changes while keeping the hose connection process direct and controlled. Operation is based on a sliding center section: slot the airbrush side into the joint to connect, then slide the middle section to detach. If the connection does not engage smoothly, the slide section can be moved up and down and the fitting retried. The set contains 1 Quick Hose Joint and 2 plugs, allowing multiple airbrush-side fittings within the same workflow. The joint size is Type-S PF-1/8. It is compatible with all Tamiya Spray-Work series airbrushes. Spray-Work Basic Airbrush requires a separately sold Connector Joint. At the workbench, the fitting helps keep paint sessions moving when different spray patterns, colours or airbrush setups are needed in sequence. It suits bench layouts where the hose stays in place and the airbrush is the part changed most often. Not compatible with Tamiya Badger airbrushes, air cans or Basic Compressor.  Warning! Not suitable for children under 14 years.

Model-making tools

R/C Tool Set (8pcs), RC tool kit, blue

€39.99

The R/C Tool Set (8pcs) gathers a focused selection of workshop tools into one coordinated kit for model bench use. With 8 pieces in the set and blue handles across the range, it brings a clear, easy-to-identify look to setup and maintenance sessions around R/C models. As a dedicated tool set for Models & Accessories and Models Supplies, it fits naturally into regular bench routines where small parts, fasteners and adjustments call for steady hand control. The matching format keeps the set visually consistent, while the compact 8-piece scope centres on the tools most often reached for during assembly support, tuning work and general upkeep. The blue finish also helps the tools stand out quickly among other bench equipment. On the workbench, the set suits repeated tasks such as preparing a new chassis, making running adjustments after use, or handling routine maintenance between sessions. It also works well as a go-to starter kit for keeping core hand tools together in one place for model building and R/C servicing.  Warning! Not suitable for children under 14 years.

Model-making tools

Rt Screwdriver PRO & (+) Bit L, ratchet tool

€35.99

The Rt Screwdriver PRO & (+) Bit L combines a ratcheting handle with a precision 72T gear for swift, controlled screw work at the bench. Short return movement keeps the tool engaged, so repeated turns feel fluid when working through model assembly, maintenance or parts changes. Mode selection sits directly on the handle tab, with settings for tightening, loosening and lock to match the task in hand. The Quick Rotation grip adds fingertip control for faster spinning on screws that have already broken free or only need light final turning. The included precision bit is crafted from chrome molybdenum vanadium steel, a material chosen for tool applications that demand dependable contact at the screw head. Its working range covers (+) screws from 3 mm to 5 mm, making it suited to a broad spread of workshop jobs. The magnetic bit supports steadier handling by helping screws stay at the tip during pickup, placement and removal. That added control is especially useful around compact assemblies, where dropped fasteners can slow progress and interrupt careful fitting. On a model bench, during chassis service or while fitting small hardware, this screwdriver keeps each turn direct and efficient.  Warning! Not suitable for children under 14 years.

Model-making abrasive material

Sanding Cloth #1000 Grit, Model Sanding Sheet

€4.69

This #1000 sanding cloth brings controlled abrasion to model finishing work, combining a soft sheet format with a mid-fine grit that suits smoothing passes where a surface needs refinement without overly aggressive cutting. The 170 x 130 mm size gives a broad working area for hand use while still fitting neatly on a bench beside paints, fillers and body parts. The cloth can be used for both dry and wet sanding, so the same sheet can support different stages of preparation depending on the material and finish being worked. The grit number identifies the abrasive grade, and within the available range from #600 to #3000, #1000 is positioned for smoothing work after coarser correction and before finer finishing steps. Its soft construction develops fewer strong fold lines than stiffer abrasive sheets, which helps keep pressure more even across contours and reduces the risk of deep scratch marks on the surface. On scale bodies, fairings, panels or other hobby components, the sheet can be folded for narrow sections or used flat across broader areas. It also suits workshop routines where one abrasive sheet needs to move between edge work, curved parts and general surface preparation while keeping handling simple and direct.  Warning! Not suitable for children under 14 years.

Model-making abrasive material

Sanding Cloth #2000 Grit for Wet and Dry Use

€4.69

This #2000 grit sanding cloth brings fine surface finishing into model hobby work with a 170 x 130 mm sheet that is easy to handle on flat sections, edges and smaller shaped areas. The fine abrasive grade supports controlled smoothing when paint, primer or filler needs a more delicate cut than lower grit sheets deliver. The cloth can be used for both dry and wet sanding, which allows the same sheet to fit different stages of bench work. Wet use can help carry away sanding residue during finishing, while dry use suits quick correction passes between steps. Within the available range of 5 types, the number after the # mark identifies the grit level, and this version is the #2000 grade. The sheet format also makes it simple to cut or position for targeted work where a bulky sanding block would be less practical. On a model bench, it suits refining painted panels, easing back filler transitions and preparing surfaces for the next coat. The soft cloth structure develops limited fold lines during use, helping avoid pronounced scratch marks when the sheet is wrapped around contours or guided by hand across detailed parts.  Warning! Not suitable for children under 14 years.

Model-making abrasive material

Sanding Cloth #3000 Grit for Wet and Dry Sanding

€4.69

This sanding cloth in #3000 grit is made for model hobby finishing where a smooth, controlled surface matters. The soft cloth format combines fine abrasion with a flexible feel, making it easier to work across curved parts, flat panels and narrow edges while keeping the sanding action even. At 170 x 130 mm, the sheet offers enough area for repeated passes before a fresh section is needed. The #3000 grit grade suits light refining work, including smoothing surfaces between finishing steps and reducing minor marks before the next stage. The cloth can be used for dry sanding or with water for wet sanding, so the same sheet adapts to different materials and finishing routines. Its construction develops limited fold lines during use, which helps prevent deep scratches from sharp creases pressing into the surface. The pack contains 1 sanding cloth. On a workbench, the sheet can be wrapped around fingertips, folded for tighter access or laid flatter across broader sections to keep pressure consistent. It fits detailed model hobby tasks where a finer abrasive is needed for careful surface preparation and clean final touch-up work.  Warning! Not suitable for children under 14 years.

Model-making abrasive material

Sanding Sponge Sheet 1000, sanding sheet

€6.19

The Sanding Sponge Sheet 1000 brings fine abrasive control to model finishing, combining a 1000 grit surface with a flexible foam backing that follows curves, edges and narrow round parts more closely than stiff sanding paper. In use, the sheet wraps around tubes, corners and small shaped sections, so the abrasive stays in contact while material is removed in a measured way. The sponge layer gives the sheet a cushioned structure that helps maintain an even touch across uneven surfaces. That makes it useful for refining molded parts, smoothing shaped components and preparing areas that need a lighter finishing pass after coarser sanding steps. The sheet can also be cut into smaller sections when a build calls for work on seams, recesses or tight detail zones. Its hand-held format suits careful finishing on plastic, resin and other common model-making materials where control matters more than fast stock removal. On the bench, it fits naturally into paint preparation, part cleanup and final surface correction before the next stage of a build. It also works well for small cylindrical pieces and rounded edges where a flat abrasive tends to skip across the surface instead of following the shape.  Warning! Not suitable for children under 14 years.

Model-making abrasive material

Sanding Sponge Sheet 180, model sanding sheet

€6.19

The Sanding Sponge Sheet 180 brings controlled abrasion to model finishing with an aluminum oxide surface bonded to a flexible 5 mm sponge base. That combination helps the sheet sit evenly on shaped parts while smoothing protrusions, seam lines and other raised areas that can interrupt a clean finish on plastic models. At 114 x 140 mm, the sheet offers enough area for broad passes across larger sections, yet it can also be trimmed with a modeling knife into smaller pieces for narrow edges, corners and localized correction. The sponge backing compresses slightly during use, which helps the abrasive stay in contact across curved surfaces instead of only touching the highest points. Beyond plastic models, the abrasive surface is also suited to finishing work on wood and metal, giving the sheet a clear role across different stages of bench work. The 180 grit sits in the more assertive end of the range for material removal and early surface preparation. On a workbench, that makes the sheet useful for refining body parts, shaped accessories and other detailed components before painting or further finishing steps. Wet sanding compatibility adds a second working method for jobs where a cleaner surface and closer control of residue are preferred.  Warning! Not suitable for children under 14 years.

Model-making abrasive material

Sanding Sponge Sheet 240, model sanding sheet

€6.19

The Sanding Sponge Sheet 240 combines aluminum oxide abrasive with a 5 mm sponge base, giving model finishing work a controlled, adaptable contact surface. Its 240 grit suits general smoothing and surface preparation, especially when protrusions, seam lines or uneven spots need to be reduced across shaped parts and detailed contours. At 114 x 140 mm, the sheet offers enough area for broad passes while still being easy to trim into smaller sections with a modeling knife. That makes it useful for narrow edges, recessed areas and custom sanding shapes that match the part being worked on. The sponge layer bends with the surface instead of forcing a flat contact point, which helps maintain a more even finish on curves, corners and sculpted details. The abrasive format is suitable for plastic models and can also be used when finishing wood and metal parts. Wet sanding use adds another practical option during bench work, particularly when a cleaner sanding process is preferred on finely shaped components. On figures, body parts, panels or scratch-built details, the sheet supports careful material removal with close control over where the abrasive meets the surface. As part of a wider sanding range with 3 abrasion levels, the 240 version sits in the middle for balanced shaping and finishing tasks.  Warning! Not suitable for children under 14 years.

Model-making abrasive material

Sanding Sponge Sheet 320, model sanding sheet

€6.19

The Sanding Sponge Sheet 320 brings controlled surface finishing to model work with an aluminum oxide abrasive layer bonded to a flexible 5 mm sponge base. That combination helps the sheet sit evenly against shaped parts while smoothing protrusions on plastic models, and it also suits finishing work on wood and metal. The 320 grit supports finer abrasion where a cleaner surface is needed before the next build step. With a 114 x 140 mm format, the sheet provides enough area for broad passes across larger sections while still remaining easy to handle at the bench. The sponge backing bends into curved panels, around sculpted forms and into harder-to-reach corners where a rigid abrasive can skip or dig in. When a smaller contact area is needed, the sheet can be cut with a modeling knife to match narrow edges, recessed details or compact parts. Wet sanding compatibility adds another working method for builders who want to adapt the finish process to the material and the stage of preparation. On scale models, figures and detail parts, the sheet supports careful cleanup after trimming, seam work or surface preparation. It fits neatly into finishing routines that move between broad smoothing and more targeted correction, especially on parts with changing contours and fine molded detail.  Warning! Not suitable for children under 14 years.

Model-making abrasive material

Sanding Sponge Sheet 400, model sanding sheet

€6.19

The Sanding Sponge Sheet 400 brings controlled abrasion and a flexible backing to model finishing work, combining 400 grit cutting action with a sponge base that follows curves, edges and narrow round parts more naturally than a rigid sheet. In the hand, the surface can wrap around tubes, rods and shaped sections, making it easier to keep contact where flat abrasives tend to miss high and low spots. That flexible structure is especially useful during shaping, seam cleanup and surface preparation on parts with changing contours. The sheet can be trimmed into smaller sections for detail work on confined areas, which helps reserve a larger piece for broader passes on panels or formed components. The sponge layer also cushions pressure during sanding, giving more control when refining small parts and reducing the abrupt feel of a hard backing on delicate geometry. On the bench, this grade fits early to mid-stage finishing tasks where visible marks, edges or uneven joins still need material removed before moving on to finer abrasives. It suits hand sanding during model assembly, part cleanup and general hobby work, especially when cylindrical or curved pieces need a sanding surface that can bend with the shape instead of fighting it.  Warning! Not suitable for children under 14 years.

Model-making abrasive material

Sanding Sponge Sheet 600, sanding sheet for models

€6.19

The Sanding Sponge Sheet 600 brings a controlled abrasive surface together with a flexible foam backing, making it easier to work across curves, edges and narrow parts that are awkward to reach with rigid sanding media. In model making and detail finishing, that combination helps smooth joins, refine shaped components and prepare surfaces with a more even touch. The 600 grit grade suits tasks that need a finer abrasive than coarse shaping, such as cleaning up small imperfections, evening out transitions and preparing parts before the next finishing step. The sponge base bends around rounded tubes and contoured pieces, so contact stays closer to the surface instead of catching only the high points. As a full sheet, it can also be cut into smaller pieces for tighter access around compact assemblies and delicate sections. This makes it useful on plastic model parts, hobby materials and other small components where controlled hand sanding matters. On the workbench, the sheet fits naturally into build and finishing routines, whether smoothing a curved part, tidying an edge or preparing a surface before paint is applied. The hand-held format supports precise, local work on individual areas without switching to bulky tools.  Warning! Not suitable for children under 14 years.

Model-making tools

Screwdriver PRO L, hobby tool, long Phillips shaft

€10.99

The Screwdriver PRO L is a handheld hobby tool built for precise manual work, with a long metal shaft and a Phillips cross-head tip that reaches screws set deeper inside assemblies. Its extended form helps when cross-head fasteners sit behind braces, inside narrow chassis sections or below surrounding parts, where a shorter driver can be awkward to position. The rounded handle combines a blue body with black grip inserts, creating a shape that supports a steady hold through repeated fastening and loosening. That direct hand feel helps with careful screw control during model assembly, RC maintenance and general bench work. The cross-head tip is designed for matching screw heads, so alignment stays clear while turning pressure is applied by hand. The clean, simple layout also makes the tool easy to keep within reach on a work surface alongside parts trays, sprues and small hardware. On a model-building bench, it suits detail-focused tasks such as fitting components, adjusting mounted parts or reopening assemblies for maintenance. In RC use, the long shaft is especially useful where surrounding structure limits access and a controlled manual turn is more useful than speed.  Warning! Not suitable for children under 14 years.

Model-making tools

Screwdriver PRO M, hobby tool, Phillips driver

€8.39

The Screwdriver PRO M is a hand tool built for precise fastening work in model building, RC maintenance and general hobby assembly. Its Phillips tip engages cross-head screws directly, while the blue and black handle shape supports a steady grip during careful bench work. The long silver shaft adds reach in tighter layouts, where screw heads can sit below surrounding parts or inside compact structures. The metal shaft gives the tool a clear, direct feel when turning fasteners by hand, which helps with measured pressure on smaller screws and controlled alignment during assembly. The rounded handle form sits securely in the hand, and the rubberized grip surface supports consistent control through repeated turns. This makes the tool useful not only for first-time builds, but also for adjustment, part changes and routine maintenance on hobby models and related equipment. On a workbench, in a parts tray setup or beside an RC chassis during service, the Screwdriver PRO M fits naturally into regular workshop use. The hanging hole at the end of the handle also makes storage simple, keeping the tool close at hand for the next repair, setup or build session.  Warning! Not suitable for children under 14 years.

Model-making tools

Sharp Pointed Side Cutter, plastic model tool

€44.99

The Sharp Pointed Side Cutter is built for close, accurate work on plastic model sprues, where small attachment points call for a narrow jaw and a clear view of the cut. Thin, pointed blades help reach confined areas around delicate molded parts, making careful separation easier during detailed bench work. The cutting blades are made from chrome-vanadic alloy and are hand-finished for optimum sharpness. That combination gives the jaws a crisp edge profile suited to trimming fine plastic sections with controlled pressure. The short angled head keeps the cutting area visible while guiding the tool into tighter spaces on runners and around smaller components. Black textured handles add a secure hold that supports steady hand positioning during repeated cuts. On the workbench, this cutter suits model preparation, part removal and cleanup before fitting or painting. It works well when a build includes slender pieces, fine detail sections or closely spaced sprue gates that need a more exact approach than a general-purpose cutter can offer. For hobby sessions focused on neat part release and controlled handling, it brings a dedicated cutting shape to the task.  Warning! Not suitable for children under 14 years.

Model-making tools

Side Cutter for Plastic, precision hobby tool

€37.99

This precision side cutter is made for plastic modeling and focuses on one job: removing parts from sprue without damaging them. The short angled cutting head supports close access around attachment points, so small molded sections can be separated with more control before sanding, fitting or final assembly. The cutter uses chrome vanadic alloy, a material chosen here for impact resistance and long life. A spring between the handles reopens the jaws after each cut, which helps maintain a steady pace when several parts need to be clipped from the same frame. The vinyl covering on the handles adds grip for careful hand positioning during detailed bench work. Together, these features suit repeated trimming tasks where clean separation matters more than force. On a model building table, the cutter fits naturally into the early preparation stage, when runners are being cleared and individual components sorted for the next steps. It also works well for careful cleanup sessions on compact plastic parts where access is limited and controlled snips are needed around narrow gates and edges.  Warning! Not suitable for children under 14 years.

Model-making tools

Side Cutter Modeler α, hobby nipper, Mint Green

€17.49

Side Cutter Modeler α brings a dedicated cutting tool into model-building work, pairing the familiar nipper format with a Mint Green finish that stands out clearly on the bench. The compact hand tool is shaped for trimming tasks around parts preparation, where clean separation and steady handling matter during assembly. In model-making use, a side cutter is typically reached for at the stage where parts come away from runners and need controlled cleanup before fitting. That makes this tool a practical match for repeated bench work across plastic model projects, especially when small components call for a precise cut rather than twisting or pulling. The α designation and the specific Side Cutter Modeler naming place it clearly within hobby-tool use rather than general household cutting. Batteries are not included. Set beside paints, sanding tools and tweezers, the Mint Green finish remains easy to pick out between steps, which helps keep the workflow moving during longer build sessions. Whether the task is opening a new kit, preparing detail parts or tidying cut points before final assembly, this cutter fits naturally into the sequence of model construction.

Model-making tools

SP Side Cutter Slim Jaw, model tool, 115 mm

€47.99

The SP Side Cutter Slim Jaw is built for one specific workshop task: removing plastic scale model parts from the sprue with clean, controlled cuts. Its sharp jaw blades and slimmer head profile help reach smaller components where attachment points sit close to surrounding frame sections, making detailed trimming work more precise at the bench. The 115 mm format keeps the cutter compact and easy to position around fine assemblies, while the slim jaw shape improves access in narrow gaps that broader cutters can struggle to reach. PVC grip covers provide a firm hold during repeated cutting passes, supporting stable hand placement when working through runners with multiple small parts. The tool is marked with the twin star logo and TAMIYA CRAFT TOOLS FOR PLASTIC. On a model building table, this cutter suits the early stages of part preparation, when clean separation from the sprue affects fit and finish in later assembly steps. It also works well for careful trimming sessions focused on smaller plastic components, where close visibility and controlled pressure matter more than heavy cutting force.  Warning! Not suitable for children under 14 years.

Model-making tools

Spray-Work Airbrush Cleaning Brush Standard

€5.99

The Spray-Work Airbrush Cleaning Brush Standard is a maintenance tool for Tamiya Spray-Work series airbrushes, made to clean the paint cup area and the section where the cup attaches to the airbrush. Its standard brush size also supports cleaning at the front opening, where twisting motion helps lift paint residue from the nozzle area during routine care. The instructions show 2 brush types in the wider cleaning system, with this version identified as the standard brush for broader internal access than the extra-fine option. It is used as part of airbrush servicing that can include removing the paint cup, loosening the needle chuck screw, and taking off the nozzle cover, nozzle and needle cover for deeper cleaning. A nozzle wrench is used for the front assembly during that process. The brush is not for use with Tamiya Airbrush Lite series airbrushes from Sparmax. On the workbench, this brush fits into regular maintenance between painting sessions or during a more thorough strip-down when spray performance starts to change. Used with care on the correct Spray-Work airbrush, it helps keep narrow passages and attachment points clear for cleaner operation in model painting tasks.  Warning! Not suitable for children under 14 years.

Model-making tools

Spray-Work Airbrush Cleaning Brush XF Tool

€6.99

The Spray-Work Airbrush Cleaning Brush XF is built for precise maintenance of Spray-Work series airbrushes, using an extra-fine brush head to clean the needle cavity and other narrow internal spaces. Its slim metal form and loop handle support controlled handling when working around small front-end components. The extra-fine format is intended for passages that standard cleaning tools cannot enter easily. Instructional material for this brush shows use in the nozzle and needle area, where careful insertion helps remove paint from tight channels. The long twisted wire stem reaches into slim openings while keeping the brush head aligned during cleaning. This brush is for use with the Tamiya Airbrush System Spray-Work series and is not intended for Tamiya Airbrush Lite series airbrushes. The documentation also identifies it as equipment for advanced users and notes that the air supply should be turned off before disassembly and cleaning. In regular workshop use, the brush fits maintenance routines for airbrushes used with fine paint work, especially when residue collects in narrow passages near the front of the tool. It can be used during nozzle and needle cleaning steps alongside careful disassembly, helping keep detailed spray work consistent across repeated painting sessions.  Warning! Not suitable for children under 14 years.

Model-making tools

Spray-Work HG Trigger Airbrush Super Fine 0.2

€254.99

The Spray-Work HG Trigger Airbrush Super Fine 0.2 brings pistol-grip handling and detail-focused spray control into hobby painting, with a 0.2 mm nozzle suited to careful work on model surfaces. The trigger mechanism changes output from fine to wide as the lever is moved, making it easier to shift between narrow passes, soft transitions and broader coats during the same painting session. The metal body combines a top-mounted paint cup, a tapered front nozzle and a rear adjustment section in one compact tool. The cup is filled from above and closed with a cover during use, keeping paint close to the spray path while helping manage movement around the work area. Instruction details also show paint thinning as part of setup, with spray results changing when paint is too thick or too thin. Internal parts can be accessed for care after use, including the needle, nozzle cover, air stop valve and valve spring, and a nozzle wrench is supplied for servicing the front end. On a model car body, the airbrush supports close, hand-controlled passes for edges, smaller sections and gradual colour changes. After painting, prompt cleaning of the cup and inner passages before paint cures helps keep the 0.2 mm nozzle and needle working as intended for the next session.  Warning! Not suitable for children under 14 years.

Model-making tools

SW Quick Hose Joint Plugs, airbrush connectors

€11.99

SW Quick Hose Joint Plugs are replacement connector sections made for the Quick Hose Joint system in Item 74561. The set contains 2 matching plugs that add extra connection points for airbrush equipment, making it easier to keep more than one setup ready at the bench. The metal construction and machined finish give each fitting a precise, compact form suited to repeated handling. Each plug has a stepped shaft and a knurled cap with a diamond-textured surface, so the fitting can be gripped securely when attaching or removing it by hand. In the Quick Hose Joint system, the airbrush and hose connect or disconnect with a single touch by sliding the center section. These replacement plugs are built to work with that mechanism, extending the same quick-change function to additional compatible connections. The set is intended for use with Item 74561 only. In a workspace where several airbrushes are used for different paints or spray tasks, the extra plugs help keep changeovers short and orderly. They also suit a bench setup that stays assembled between sessions, with dedicated fittings ready for the next hose connection when airbrushing resumes.

Model-making adhesive

Tamiya Cement w/Brush 20ml Plastic Model Glue

€3.791 l = €189.50

Tamiya Cement w/Brush 20ml is a liquid adhesive for plastic modeling that combines controlled application with a compact 20 ml bottle. The brush built into the screw cap reaches directly into seams and contact points, making it easier to place cement where body parts meet during model assembly. The cement is described for strengthening a Dangun Racer body by applying it to the fitted parts before they are secured with screws. That sequence matters: the adhesive works at the mating surfaces while the screws hold the parts in position, helping the body come together as a more secure shell. The formula is a colorless liquid with ester odor and a density of 0.86 g/mL at 20°C. The safety data sheet classifies it as flammable and notes that it should be used only in well ventilated areas. On the workbench, the brush-cap bottle suits careful seam work on plastic bodies, small panels and other fitted sections where a broad applicator would be less precise. It fits naturally into model kit assembly sessions that call for measured adhesive placement rather than heavy glue flow, especially when reinforcing joined plastic sections before final fastening.

Model-making tools

Tamiya HG Straight Tweezers Precision Craft Tool

€19.99

HG Straight Tweezers bring precise control to close-up model work, with a straight stainless steel form that carries finger movement directly to the fine pointed tips. That direct line between hand and tip helps when lifting, placing and adjusting small plastic model parts where a broader tool can hide the contact point. The precision-made stainless steel body has a slim, tapered profile suited to detail tasks that call for a clear view of the work area. Fine tips can grip small edges and contact points for careful alignment during assembly, touch-up work or part placement. The straight pattern differs from angled tweezers by keeping the approach in line with the hand, which supports exact positioning on flat sections, narrow joins and compact assemblies. The satin metal finish and narrow arms also suit bench setups where controlled, repeatable movements matter. On a model bench, these tweezers fit naturally beside sprue cutters, files and other hobby tools for handling tiny components that are awkward to pick up by hand. They also suit careful placement work on detail sections where accuracy and visibility matter most.  Warning! Not suitable for children under 14 years.

Model-making tools

Thin Blade Craft Saw, modeling tool with spare blade

€24.49

The Thin Blade Craft Saw brings a narrow cutting profile and fine serrated teeth to detailed modelmaking work, supporting clean, controlled cuts where bulkier workshop saws can feel too coarse. The black handle and long metal blade create a focused layout for trimming small sections, opening narrow gaps, and separating delicate parts with measured hand control. A round tightening knob mounts the blade to the handle, giving the tool an adjustable, replaceable blade setup rather than a fixed one-piece form. That construction helps keep the saw ready for repeated bench use and makes the included spare blade a practical part of the set, not an afterthought. The slim blade shape is especially useful when working close to molded details, along panel lines, or through thinner hobby materials that call for accuracy over force. The fine tooth pattern is built for careful forward-and-back strokes that remove material gradually and help maintain a defined cut path. On a modelmaking bench, the saw fits naturally alongside trimming, fitting, and part-preparation work before final assembly or finishing. It suits tasks such as cutting through attached sections on model components, refining openings, or making careful adjustments where a knife alone is less suitable. The included spare blade adds continuity for longer projects and keeps the tool ready for the next precise cut.  Warning! Not suitable for children under 14 years.

Model-making tools

Transmitter Bag, RC carry case with accessory storage

€59.99

The Transmitter Bag is built to keep an RC transmitter protected and organised while travelling to the track, workshop or storage shelf. Its upright rectangular format, black finish and blue zipper details give the bag a focused racing look, while the dedicated internal transmitter compartment keeps the controller in its own defined space instead of shifting among loose gear. Inside, the layout separates equipment into clearly usable zones. Above the main transmitter area sits a sub-compartment for related R/C equipment or parts, and the front cover carries an inner pocket for additional stowage. The front panel opens on 3 sides, which creates a wide access point when packing, unpacking or checking gear between runs. A soft strap cover handle supports brief hand carry, and the strap can be attached at different positions to convert the bag for shoulder use. Rear attachment points also allow the bag to be secured to Item 42337 R/C Trolley Pit Bag. This layout suits race days, club meetings and travel between home and circuit, where a transmitter often needs its own protected place rather than sharing space with tools and spares. The bag also works well as a compact grab-and-go case for carrying a controller and a small set of related RC essentials in one organised format.

Other accessories

Ultra Thin Aluminum Sticker, foil sheets, 0.01 mm

€9.99

Ultra Thin Aluminum Sticker brings real metal surface material into model finishing with 2 foil sheets at 0.01 mm thickness. The format suits builders who need a very fine layer for selected panels, trim sections or localized detailing where molded lines and body contours should remain visible. The metallic surface gives scale projects a crisp, technical look that works especially well on aircraft skins, car body accents and other hard-surface subjects. Each sheet can be cut to shape for the exact section being covered, which supports careful work around openings, edges and narrow framed areas. The thin foil format is useful when a painted effect is not the goal and an actual metal layer is preferred for visual contrast. On curved bodywork or tapered sections, the material can be adapted more closely than thicker sheet stock, making it suitable for detail-focused finishing rather than broad structural covering. The 2-sheet pack also leaves room to test placement on smaller sections before committing to a larger area. In a workshop setup, the sheets fit naturally into body detailing, aircraft panel work and custom trim application. They can be used during a fresh build or added later to refine a completed model with extra surface variation and sharper metallic definition.  Warning! Not suitable for children under 14 years.

Model-making tools

Work Stand w/Magnifying Lens, hobby work stand

€139.99

The Work Stand w/Magnifying Lens brings magnification, lighting and bench organization together in one tabletop station for detailed model work. An adjustable arm carries the magnifying lens above the work area, while 6 white LEDs add direct light for part cutting, assembly, painting and decal application on small components. The base is shaped as a practical workstation rather than a plain stand. A brush support, clip holder, bottle holder and decal tray keep key tools and materials within reach during longer sessions. The bottle holder fits Tamiya cement, acrylic paint and enamel paint bottles, and the cutting mat frame secures the Tamiya 74056 A4 cutting mat when used. A backboard is included to help stop parts from flying off while cutting pieces from sprues. Power comes from 4 R20/D/UM1 batteries or an AC adapter, both required separately. On a hobby desk, the stand supports close-up marking, trimming clear parts, checking painted surfaces and placing decals with a clearer view of edges and small details. The carry grip also makes it easier to move the workstation between storage and the bench when the next build session starts.  Warning! Not suitable for children under 14 years.

Model-making adhesive

Extra Thin Cement Quick-Set, model cement

€6.991 l = €174.75

Extra Thin Cement Quick-Set is a liquid model cement designed for precise bonding on plastic model assemblies. Its extra thin consistency lets the adhesive run into narrow joins by capillary action, making it useful when parts are already positioned and only the seam needs cement. The quick-setting character supports a faster working rhythm on builds with many small attachment points. The 40 ml bottle contains a clear liquid cement for detailed bench work, and the screw cap carries an integrated brush for controlled application along edges, corners and fine contact lines. This format helps place a small amount exactly where the joint is needed instead of flooding surrounding detail. The bottle shown is glass, which gives the cement a stable container for repeated workshop use. The formulation is identified as a solvent-based plastic cement, with ethyl acetate, acetone and butanone listed in the safety data. The liquid has a density of 0.86 g/mL at 20 °C and a boiling point of 56 °C. On aircraft, cars, tanks or other scale builds, this cement suits assembly stages where thin parts, interior sections or long body seams benefit from a flowing adhesive. Use requires careful handling in well-ventilated spaces, as the safety data states that the liquid and vapour are highly flammable and may cause serious eye irritation or drowsiness.  Warning! Not suitable for children under 14 years.

Model-making adhesive

Tamiya Cement w/Brush 40ml, plastic cement

€4.991 l = €124.75

Tamiya Cement w/Brush 40ml is a plastic model cement designed for precise bonding work on scale model assemblies. The built-in brush stored inside the screw cap allows the cement to be applied directly to seams and connection points, helping keep placement controlled while parts are aligned on the workbench. The cement comes in a 40 ml bottle, giving a useful amount for repeated building sessions and longer projects. The bottle is made of glass, and the liquid inside is transparent with an ester odour. According to the supplied safety data, the formula contains solvents including n-butyl acetate, acetone and cyclohexane. The safety documentation also classifies the cement as flammable liquid category 2 with a flash point of -18 °C and a boiling point of 56 °C. It is intended for use in well-ventilated areas and should be handled with care during model-building work. On the bench, the brush format suits tasks such as running cement along part edges, touching adhesive into narrow joints and working around small plastic components during assembly. The clear bottle and white label make the cement easy to spot among tools, paints and parts trays, whether used for a single kit or kept ready for regular hobby sessions.  Warning! Not suitable for children under 14 years.

Model-making adhesive

Mark Fit 40ml Decal Solvent with Brush

€4.991 l = €124.75

Mark Fit 40ml is a decal solvent for scale models that helps wet slide decals settle onto curved and uneven surfaces with a cleaner, closer finish. The clear liquid comes in a 40 ml bottle with an attached brush, making it easy to apply the solvent exactly where the decal needs support. The application method is part of what makes the formula useful in detailed model work. First, the solvent is brushed onto the area where the decal will sit. After the decal is placed, it can be slid into position with a wet finger, then excess water and trapped air can be removed with a soft cloth or cotton swab. A second coat over the decal helps it conform more closely to the model surface while it dries. This sequence is especially helpful around bumpy sections, curved bodywork and other shapes where decals are harder to settle evenly. On a body shell, fairing, tank or other contoured part, Mark Fit supports sharper decal placement without changing the graphic itself. It suits careful finishing sessions where panel lines, raised details and compound curves call for more control than water alone can provide.  Warning! Not suitable for children under 14 years.

Model-making masking tapes

6mm Masking Tape Refill, model supply, 18m roll

€2.891 m = €0.16

This 6 mm masking tape refill is made for model finishing where narrow coverage and crisp paint separation matter. The thin tape follows edges closely and adheres well even on uneven surfaces, making it useful for curves, raised details and tight sections on scale builds. Its strong adhesive layer holds the tape in place while paint is applied, yet the material is designed not to absorb colour or leave unsightly marks behind. That combination supports cleaner transitions between painted areas and helps preserve the surface appearance on both painted and unpainted parts. With a roll length of 18 m, the refill suits repeated use across multiple sessions, whether masking body lines, window frames, trim sections or small detail zones that need a precise boundary. The narrow format fits hobby benches where careful control matters more than broad coverage. It can be used on scale plastic models and radio control models when sharp lines are needed for multi-colour finishes, touch-up work or staged painting steps. The refill format also makes it a practical choice when an existing tape dispenser or holder is already part of the modelling setup.

Model-making adhesive

Decal Adhesive Softener, model decal solution

€5.891 l = €589.00

Decal Adhesive Softener is a decal setting liquid for scale model work that combines adhesive and softening properties in a 10 ml bottle. Used with water-slide decals, the transparent formula helps the marking film settle onto painted surfaces and follow shaped sections more closely, so insignia, stripes and small printed details sit with a cleaner painted-on look. The mixture is described as polyvinyl alcohol in solvents and is intended specifically as a decal adhesive with softener for Nassschiebebilder. The liquid is transparent, has an alcohol odour, and a density of 0.99 g/mL at 20°C. Physical data in the supplied sheet lists a boiling range of 82 to 120°C, a flash point of 35°C and a vapour pressure of 4.4 kPa at 20°C. These details place it firmly in the specialist finishing stage of model building, where decal placement and surface contact matter as much as paint and assembly. On aircraft, cars, motorcycles or military subjects, the bottle size suits bench work where only a small amount is needed at a time for serials, sponsor graphics or panel markings. The supplied safety data classifies the liquid as flammable and eye irritating, so handling belongs in a well-ventilated workspace with appropriate care during application and storage.

Model-making adhesive

Mark Fit Strong 40ml, decal solvent, brush cap

€4.991 l = €124.75

Mark Fit Strong 40ml is a decal solvent for scale model work where standard decal placement struggles on curved, uneven or matte-painted surfaces. The stronger formula is designed to soften the decal film so markings can settle more closely over raised details, recessed areas and changing contours, giving complex bodywork and shaped panels a cleaner finished look. The application method is built around direct, local control. Solvent is first brushed onto the area where the decal will be positioned, then the decal is slid into place with a wet finger. A soft cloth or cotton swab removes excess water and trapped air bubbles before another coat is brushed over the decal to help it conform to the model surface as it dries. The cap includes the brush applicator, so the bottle is ready for precise placement straight away. This 40 ml bottle suits regular bench use, whether adding small sponsor logos, instrument markings or larger graphics across compound curves. Care is required on painted finishes, as the formula may cause damage in some cases, particularly on surfaces painted with acrylic paints. Flammable and warning hazard pictograms are shown on the safety information.  Warning! Not suitable for children under 14 years.

Model-making masking tapes

Masking Tape 10mm, modelling tape with dispenser

€6.691 m = €0.37

This modelling tape combines a thin tape body with strong adhesion, giving masking work a controlled feel on painted parts, bare surfaces and shaped model sections. The 10 mm width suits trim lines, panel areas and repeated strip placement, while the 18 m roll provides enough length for extended painting sessions at the bench. Its adhesive layer is described for uneven surfaces, which matters when tape has to follow contours, edges or small changes in level on scale plastic and radio control models. The thin construction helps the tape sit close to the surface during spraying or brush painting, supporting clean paint breaks instead of soft, wandering edges. A dispenser is part of the format, keeping the roll together between sessions and making it easier to pull and cut manageable lengths during detail work. The tape is intended for moments when colour separation has to stay precise, whether masking a body shell, protecting adjacent painted sections or defining narrow bands before the next coat goes on. It also suits unpainted parts that need temporary coverage during preparation and finishing. On the workbench, the combination of controlled width, long roll length and clean removal supports steady progress across single details and larger multi-step paint jobs.

Model-making masking tapes

Masking Tape Refill 18 mm, model tape roll

€5.191 m = €0.29

This masking tape refill is built for model making where clean edges and dependable adhesion matter. With a 18 mm width and 18 m length, the roll covers broad sections, long stripes and repeated masking tasks on scale builds while keeping the working area neat and easy to define. The thin tape construction helps it sit close to the surface, which is especially useful on contours, panel transitions and other uneven areas that can challenge ordinary tape. Its strong adhesive grip is intended for modelling use and holds firmly during painting, while the material is designed not to absorb paint colour. That combination supports clearer colour separation and a tidier finish on painted parts. The tape can also be used on unpainted scale plastic or radio control models when precise coverage is needed before the next step in finishing. As a refill roll, it suits regular bench use where masking lines, borders and protected sections need to be laid down quickly and removed cleanly after spraying or brush work. On body shells, aircraft parts, car panels or detail sections, the 18 mm format gives enough coverage for wider areas while still allowing accurate placement by hand.

Model-making adhesive

CA Cement Gel Type 3g, model adhesive gel

€4.991 kg = €1,663.33

CA Cement Gel Type 3g is a gel-type cyanoacrylate adhesive made for model-making tasks that call for fast bonding and more controlled application than a runnier glue. The 3 g tube and narrow nozzle suit small parts, tight seams and careful placement on detailed assemblies, where a compact bead of adhesive helps keep work focused and tidy. The gel consistency is useful when bonding contact points that need the adhesive to stay where it is dispensed before the parts are pressed together. This makes the tube a practical choice for repair jobs, detail work and short workshop sessions with limited glue use. The formula is identified as cyanoacrylate, with ethyl-2-cyanoacrylate listed at more than 85% in the safety data. Storage is specified at 2-8 °C, and the adhesive is described there as light- and moisture-sensitive. The same document also states the warning classification for skin irritation, serious eye irritation and respiratory irritation. On the bench, the small tube format is easy to keep alongside cutters, files and sanding tools for quick access during a build. It suits moments when a part needs a rapid join, a loose section needs reattachment, or a narrow edge calls for a carefully placed line of adhesive rather than a wide spread.  Warning! Not suitable for children under 14 years.

Model-making masking tapes

3mm Masking Tape, model masking tape, 18 m

€5.791 m = €0.32

This 3 mm masking tape is made for model finishing where narrow coverage and clean paint separation matter. The thin tape format follows fine contours and small sections more easily than wider strips, making it useful around trim lines, body details and other tight masking zones on scale plastic and radio control models. The adhesive layer is designed to hold firmly, even on uneven surfaces, so the tape can be pressed down across shaped parts and raised details before paint is applied. Because the tape does not absorb paint color, it supports crisp edges and helps keep the masked line clear when different colours meet. It can be used on painted or unpainted surfaces, which makes it suitable for both fresh builds and later detailing work. With a roll length of 18 m, the tape suits repeated workshop use across body shells, small components and staged paint jobs that need several masking passes. The 3 mm width is part of a wider size range that also includes 1 mm and 2 mm versions, allowing narrow line work to stay consistent when a finer masking width is needed.

Model-making masking tapes

Masking Tape 6mm, modeling tape with dispenser

€6.091 m = €0.34

This 6 mm masking tape is made for modeling work that depends on crisp paint boundaries and controlled placement. The thin tape conforms neatly as it is applied, which helps when following narrow trim lines, small edge sections and detailed body contours on scale plastic and radio control models. Its strong adhesive holds reliably even on uneven surfaces, so masking stays where it is placed while paint is applied around raised details and shaped sections. The 18 m length gives the roll useful reach for repeated paint sessions, from small corrections to larger multi-step masking jobs. The integrated dispenser keeps the roll contained and ready to pull, making it easier to handle short lengths for precise placement at the bench. The housing also helps keep the tape clean between sessions. The tape is suited to both painted and unpainted model surfaces where clear separation lines are needed. Because it does not absorb paint color and does not leave unsightly marks, it supports tidy results on body shells, trim areas and other detailed sections that benefit from careful masking before spraying or brush painting.

Model-making adhesive

Multipurpose Cement Clear, model adhesive, 20 g

€12.791 kg = €639.50

Multipurpose Cement Clear is a model adhesive made for clean bonding work on clear and painted parts. The transparent formula helps keep attention on the assembled section rather than on the join itself, which matters on windows, light covers, canopies and other visible details. With 20 g in the tube, the cement fits neatly into regular bench work without taking up much space among knives, files and sanding tools. The tube format supports careful placement during model assembly, especially on smaller contact points where excess adhesive can distract from painted finishes or transparent pieces. Its stated use on clear and painted parts makes it a practical choice when a build combines finished surfaces with sections that still need secure attachment. The white screw cap closes the tube between sessions, and the compact pack is easy to keep alongside other modelling supplies for repeat use on ongoing projects. On the workbench, this cement suits detail-focused tasks such as fitting cockpit glazing, attaching lenses or securing painted trim after the main structure is complete. It also works well as a handy adhesive to keep nearby for touch-ups, repairs and late-stage assembly jobs where a clear bond line is the better visual match.  Warning! Not suitable for children under 14 years.

Model-making adhesive

Paint Remover 250 ml, model paint stripper

€20.491 l = €81.96

This 250 ml Paint Remover is made for stripping paint from already painted models and preparing parts for a fresh finish. The liquid removes Tamiya acrylic, enamel and lacquer-based paints from polystyrene parts, and it can also be used on plated plastic parts when a build calls for the plated layer to come off before repainting. For local correction, the remover can be applied with a cloth or a cotton swab to lift excess colour from small areas. When a whole section needs to be cleared, painted or coated plastic parts can be placed in the liquid for a short soak. Small parts are treated for about 10 minutes, while the immersion time should not exceed 1 hour. After soaking, loosened paint is washed off with a brush, then the parts are rinsed with water and left to dry completely before the next finishing step. The formula is not suitable for ABS plastics. On the workbench, this makes it easier to correct paint runs, clear older finishes from model parts or remove plating before a new colour scheme. It suits repainting jobs, restoration work on previously finished builds and careful surface preparation before the next coat is applied.  Warning! Not suitable for children under 14 years.

Model-making tools

Cera-Grease HG 10g, ceramic grease, hobby care

€10.291 kg = €1,029.00

Cera-Grease HG 10g is a ceramic-based lubricant for model maintenance, formulated with Boron Nitride to support smooth movement in fine mechanical parts. Applied to gears and bearings in MINI 4WD cars, R/C cars and Robocraft assemblies, it helps reduce friction where repeated motion and close tolerances matter most. The formula is suitable for both plastic and metal parts, which makes it useful across mixed-material drivetrains, rotating joints and transmission components. The grease comes in a 10 g aluminum tube, and the narrow nozzle helps place a small amount directly onto compact contact areas instead of spreading it across surrounding parts. That controlled application is especially useful when servicing gear trains, bearing seats and other tightly packed mechanisms that need precise lubrication rather than broad coverage. The white paste format is designed for hobby workshop use on model vehicles and related mechanical builds. On a maintenance bench, Cera-Grease HG fits naturally into routine care before running sessions or after parts cleaning. A small amount can be applied to moving assemblies during setup work on MINI 4WD, R/C or Robocraft builds, while power switches should be left free of grease as stated.

Model-making tools

Modelers Side Cutter, hobby tool for plastic parts

€17.99

The Modelers Side Cutter is built for clean, controlled work on plastic parts used in scale models and Mini 4WD builds. Narrow cutting jaws and a hand-friendly format help guide the tool into small spaces around sprues, gates and closely placed components, where accurate trimming matters before test fitting, sanding or paint preparation. The blades are made from hardened carbon steel, a material chosen here for lasting edge retention during repeated use on plastic runners and molded parts. The cutter is designed specifically for plastic, making it a focused bench tool for separating parts rather than a general workshop cutter. A spring-loaded action reopens the handles after each cut, which supports a steady cutting rhythm when working through multiple pieces in one session. The gray finish keeps the look understated on the workbench while the pointed jaw shape helps maintain a clear view of the cut line. On a model bench, this cutter suits early build stages such as removing body parts, chassis pieces or detail components from runners before cleanup. It also fits compact hobby setups where precise hand control and a clear approach to small plastic sections make preparation work more exact and efficient.  Warning! Not suitable for children under 14 years.

Model-making tools

Paint Mixing Jar 23ml Round Glass Hobby Jar

€2.89

This round 23 ml paint mixing jar brings a clean, practical format to colour preparation on the workbench. The clear glass body keeps the contents visible at a glance, so mixed shades, remaining volume and paint condition are easy to check while preparing small batches for model finishing. The compact jar shape suits measured hobby use where only a limited amount of paint is needed at one time. A ribbed screw cap adds grip for repeated opening and closing, which helps during sessions that move between mixing, testing and storing. The round profile also keeps the format straightforward to handle when preparing custom shades, separating colours for detail work or keeping a ready-mixed batch aside for the next stage. On a modelling bench, the jar fits naturally into painting routines for miniatures, scale builds and fine touch-up tasks. It works well for mixing a fresh colour before brush application, holding a prepared shade between steps or keeping a small amount of paint ready for later corrections on the same build.

Model-making adhesive

Decal Adhesive 10ml, model adhesive

€6.291 l = €629.00

Decal Adhesive 10ml is a dedicated model adhesive for water-slide decals, made to help markings stay in place on smooth painted surfaces. The compact bottle format suits careful bench work, where small amounts can be applied exactly where a decal needs extra hold. The formula is based on polyvinyl alcohol with water, a combination identified in the supplied data for this adhesive mixture. The 10 ml content fits detail-focused modelling jobs such as insignia, numbering and fine graphic sections without taking up much space in a tool tray. The clear workshop role is straightforward: support decal placement, help the film bond to the surface and keep finishing work controlled on scale builds. The bottle shown in the supplied material uses a tall black cap, which gives a secure grip when opening and closing between short application steps. On the workbench, this adhesive fits naturally into the decal stage after painting, when small graphics need a steadier bond than water alone provides. It suits model makers handling aircraft, cars, armour or other scale subjects that rely on crisp markings to complete the final look.  Warning! Not suitable for children under 14 years.

Model-making tools

Paint Mixing Jar Mini 10ml, round hobby jar

€2.89

The Paint Mixing Jar Mini 10ml is a compact round glass jar made for preparing and holding small amounts of hobby paint. Its clear body keeps the colour and level visible during mixing, while the screw cap closes the jar for short-term storage between painting steps at the workbench. The 10 ml capacity suits touch-up colours, test mixes and small custom batches that do not need a larger container. The round shape keeps the format simple and easy to handle when paint is being stirred, checked and set aside for the next stage of a model project. Glass gives the jar a clean, smooth interior surface for liquid paint, and the ribbed cap adds grip when opening and resealing the container with paint on the fingers. The transparent wall also helps compare mixed tones across several jars without opening each one. On a hobby bench, the mini jar supports organised paint preparation for detail sections, accent colours and repeat mixes used across several sessions. It also works as a dedicated container for separating a small quantity from a main paint bottle before brush work or other precise application begins.

Model-making adhesive

40ml ABS Cement Bottle for Model Assembly

€6.791 l = €169.75

This 40 ml ABS cement bottle is made for model assembly work on ABS parts, using a clear liquid formula that suits precise bonding and repair on compatible components. The square glass bottle and ribbed blue screw cap give the cement a compact bench presence that is easy to place, open and close during focused build sessions. The label identifies the cement specifically for ABS, which matters when a build combines different materials and the adhesive choice needs to match the part being joined. The safety data names it as a solvent-based mixture and lists acetone at under 60%, with a solvent content of 85%, a density of 0.9 g/ml at 20 °C and a flash point of -18 °C. Hazard pictograms on the label mark the cement as flammable and as an irritant warning, so handling and storage belong in a well-prepared hobby workspace. The bottle format keeps the quantity contained in one dedicated container rather than loose transfer into separate pots. On the bench, this cement fits the moments when ABS housings, structural sections or detail parts need a material-specific bond during a build or a repair. It also suits restocking a model toolkit for repeat assembly tasks, where a clearly marked 40 ml bottle can stay alongside cutters, files and other workshop essentials between projects.  Warning! Not suitable for children under 14 years.

Model-making masking tapes

Masking Tape 18mm, model supply, with dispenser

€8.791 m = €0.49

This 18 mm masking tape brings precise paint control to model finishing, with a thin tape body that follows surfaces closely and a 18 m roll length that supports longer masking passes across shells, panels and other broad sections. The included dispenser keeps the roll compact and ready at the bench, so the tape can be pulled, positioned and cut with steady handling during painting work. Its strong adhesive is designed for modeling use and adheres well even on uneven surfaces, which helps when masking around molded contours, panel transitions or raised details. The tape is intended for sharp and crisp lines, making it useful wherever two paint areas need a clearly defined boundary. Because the material does not absorb paint color, it helps maintain a cleaner edge during spraying or brush application. It is also suited to painted and unpainted scale plastic models as well as radio control models, giving the same roll a clear place in both finishing and repaint work. On a workbench, the 18 mm width suits larger coverage zones such as body sections, roof areas or side panels where narrow tape would take longer to place. It also works as a quick masking layer before adding narrower strips for tighter curves or smaller graphic details. For touch-ups, full repaint jobs or separating color blocks on RC bodies, the roll supports controlled, repeatable masking with less cleanup after removal.

Model-making masking tapes

Modeling Wax with Applicator for Scale Models

€16.791 l = €559.67

Modeling Wax with Applicator adds a finishing step to painted scale models, combining polishing wax and a dedicated cloth in one set for controlled surface care at the workbench. The wax is intended for model building use and suits smooth exterior areas where a clean, even sheen helps completed bodywork look more refined under light. The bottle contains 40 ml and uses a pointed cap that supports measured dispensing onto the cloth instead of flooding the surface. According to the provided safety data, the wax is a liquid O/W emulsion with additives, with a pale blue to green colour and a pH value of 7 at 25 °C. That composition makes it a specialised finishing supply rather than a paint or adhesive, giving model builders a separate step for polishing cured surfaces. The included applicator cloth is shown folded for hand use, allowing the wax to be spread, worked in and buffed with direct control across panels, cowls or other finished sections. On a completed car body, aircraft fuselage or other painted shell, the wax can be applied after the main finishing stages to refine the look of the surface before display. It also fits routine bench use when a finished build needs a fresh polish after handling, transport or time in a display cabinet.  Warning! Not suitable for children under 14 years.

Model-making masking tapes

150mm Masking Tape w/Sheet, masking film roll

€11.291 m = €1.13

This masking tape with attached polyethylene sheeting combines edge definition and surface cover in a single 150 mm format, making paint preparation faster and more controlled around model parts and nearby sections. The clear film unrolls from the tape edge in one motion, so larger areas can be covered without building up multiple separate layers by hand. The roll measures 10 m in length, which supports repeated use across priming, colour coats and detail work. Polyethylene sheeting is resistant to paint, helping reduce the chance of seep-through while the taped edge marks a clean boundary for the area being worked on. The sheeting is made as a double layer, and the layers can be cut apart when a wider piece is required for broader coverage. This gives the roll added flexibility for narrow sections, larger panels and changing masking layouts during a project. On a model bench, the roll suits jobs where overspray needs to be kept off surrounding surfaces while a defined edge stays in place. It can be used to cover adjacent body sections, protect nearby parts during airbrushing, or prepare larger areas before multi-stage paint application.

Model-making adhesive

CA Cement Accelerator, adhesive accessory, 10ml

€12.49

This CA Cement Accelerator is a focused workshop aid for faster bonding with CA cement, especially where tiny contact areas leave little room for error. The alcohol-based formula is intended for model assembly and keeps damage to plastic parts to a minimum, which matters when working close to visible surfaces and fine detail. Application follows a clear 2-surface method: place the accelerator on 1 cementing surface and the CA cement on the other, then press both parts together to form a strong bond quickly. That sequence suits photo-etched details, slim attachment points and other delicate joins where a standard curing pace can slow careful work. The bottle carries 10 ml, a practical amount for repeated bench use without taking much space among knives, tweezers and sanding tools. An applicator brush built into the cap helps place the liquid exactly where it is needed, which is useful when fitting narrow metal details or parts with only a very small cementing surface. On a model bench, that controlled application supports cleaner handling during detail assembly, repair work and finishing stages where excess liquid can interfere with alignment.  Warning! Not suitable for children under 14 years.

Other accessories

Plastic Beams 1mm Round (10), model supplies

€6.49

Plastic Beams 1mm Round (10) brings a clean, uniform rod format to model building, with 10 round beams at 1 mm diameter ready for precise custom work on miniature projects. The narrow profile suits fine additions where a consistent circular section matters, whether shaping small supports, adding linear detail or preparing replacement parts for a careful rebuild. Each beam can be cut to length and adapted to the layout of the build, giving model makers raw material for scratch-built sections that need repeatable dimensions across several matching pieces. The round cross-section lends itself to pins, rods, braces and other slim structural elements where flat strip or sheet stock would not match the intended form. With 10 pieces in the pack, there is enough stock to plan test pieces, mirrored parts or several small assemblies within the same project. On the workbench, these beams fit naturally into detail-focused tasks such as refining body features, adding framework touches or replacing missing small parts with a closer visual match. The 1 mm size also supports careful integration into compact spaces where larger rod stock would overpower the scale of the build.

Other accessories

1 mm Square Masking Stickers, model masking strips

€6.49

These 1 mm Square Masking Stickers bring fine control to paintwork where broad masking tape is too wide. The narrow pre-cut format helps define straight separations, slim borders and geometric accents on detailed hobby surfaces, keeping the focus on clean lines and careful finishing. The pack contains 10 masking strips, giving room for repeated layouts or multi-stage colour work across several sections. Their square profile suits edges, corners and panel-style divisions that call for a consistent width from start to finish. On plastic models, RC bodyshell details, miniatures or other painted parts, the thin format helps isolate narrow areas that would be difficult to cut evenly by hand. This makes them useful for stripe work, framed sections and precise paint boundaries where symmetry matters. On the workbench, the strips fit naturally into detail painting sessions that involve layered colours, touch-ups or sharply defined trim lines. They also support careful planning before spraying or brush painting, especially when a build calls for repeated narrow markings across multiple surfaces.

Other accessories

2mm Round Plastic Beams, model building rods

€4.59

These 2 mm round plastic beams add a straightforward building material to model work that calls for clean lines, repeatable dimensions and small-scale fabrication. The round profile suits custom supports, braces and shaped details, while the white material makes marking and trimming easy to follow at the bench. With 10 beams in the pack, there is enough matching stock for test pieces, mirrored parts or several stages of the same build. The slim diameter works where flat sheet or thicker stock would be too bulky, and the uniform round section helps keep scratch-built elements visually consistent across a chassis detail, body modification or workshop-made accessory. The beams can be cut to length, combined with other hobby materials and adapted to many kinds of model construction where a narrow rod is the right starting point. They fit naturally into spare-parts drawers, tool caddies and ongoing project boxes, ready for quick use when a build needs a brace, pin, spacer-style detail or a simple custom addition. On the workbench, the pack serves as practical raw material for measured fabrication rather than a single one-use component.

Other accessories

2mm Square Beams, Model Building Material Set

€4.59

This set of 2 mm square beams gives model builders a clean, uniform building stock for scratch construction, structural detailing and custom modifications. The straight profile helps when creating framed sections, narrow supports or crisp edges, whether the workbench holds a scale structure, a diorama element or a one-off conversion. The pack contains 10 beams, providing matching lengths for repeated sections and measured layouts. The white finish makes cut lines and fit checks easy to read during planning and assembly. In small-scale work, a square section like this can be used where flat strip would not give the same defined corner or boxed-in look. The consistent 2 mm format also helps when combining several pieces into grids, braces or layered framework. On a hobby bench, these beams suit jobs such as reinforcing openings, building internal frames, outlining panels or adding architectural detail to scenery pieces. They can be trimmed to length and arranged to match the exact geometry of the build, making them a practical material choice for careful, parts-led model construction.

Model-making adhesive

CA Cement Micro Nozzles, adhesive accessory, 10-pack

€4.09

These CA Cement Micro Nozzles add a finer application point to adhesive work where small joints and narrow seams need more accuracy than a standard bottle opening can offer. The pack contains 10 nozzles, each with a 2.5 mm connection section for use with compatible Tamiya CA Cement bottles, including Item 87062 and 54511. The very fine tube lets cement travel toward the tip by capillary action. During detailed assembly, that narrow path helps place adhesive exactly where two parts meet instead of flooding the surrounding area. When work pauses, cement hardens at the tip and blocks the opening until the next use, making the nozzle itself part of the dispensing control. This mechanism suits careful bonding on compact model sections where excess adhesive can mark nearby detail. On the bench, the 10-piece pack supports repeated use across multiple builds, repairs or part-fitting sessions. The slim shape is suited to moments that call for short, precise adhesive runs along edges, corners and small contact points. These nozzles are intended specifically for Tamiya CA Cement rather than general liquid transfer, and the 2.5 mm diameter distinguishes them from Item 53580 with its 3.0 mm connection size.

Other accessories

Epoxy Putty Smooth Surface, 2-part modeling putty

€23.991 kg = €239.90

Epoxy Putty Smooth Surface is a 2-part modeling putty made for shaping, filling and refining model work with a cleaner finish. The 100 g pack combines 2 separately wrapped components, with 35 g in one part and 65 g in the other, ready to be kneaded together when fabrication or repair work begins. The Smooth Surface formulation suits projects where the final contour matters as much as the build itself. It can be used for RC-modeling detail fabrication, sculpting, kit modifications and repairs, giving model makers a material that can bridge gaps, build up forms or refine custom sections. The 2-compound format helps control when the curing process starts, because the components stay separate until mixing. That makes it practical for staged work on body alterations, added details or scratch-built shapes that need careful placement before finishing. The larger 100 g quantity also supports broader jobs that go beyond small touch-ups. On the bench, the putty fits naturally into custom model workflows, whether the task is reshaping a panel line area, building a new contour, or correcting a damaged section before sanding and paint. It also suits full-scratch fabrication where a smooth outer surface helps define the final form with less follow-up correction.  Warning! Not suitable for children under 14 years.

Model-making adhesive

Mark Fit Super Strong 40ml Decal Setting Solution

€5.991 l = €149.75

Mark Fit Super Strong 40ml is a decal setting solution made for demanding marking work on model surfaces where standard applications can struggle. The liquid softens thicker decals so they can settle more closely over uneven areas, rounded sections and matte finishes, helping printed markings sit down with a cleaner painted-on look. The bottle contains 40 ml and uses a brush applicator fixed to the underside of the cap, which keeps application direct and controlled during placement. This Super Strong version sits above the standard Mark Fit and Strong Mark Fit formulas in strength and is intended for especially difficult target surfaces or thicker decal films. The liquid is a clear, transparent solvent mixture with an alcohol odour, and the safety data lists a flash point of 25 °C. Because the stronger formula may damage some decals or affect painted surfaces, it is recommended for advanced users. On a body shell, aircraft fuselage or other shaped model part, the brush can place the solution exactly along edges, recesses and compound curves as the decal settles into place. It suits finishing stages where markings need extra help to conform over detail that would otherwise leave raised edges or trapped air.

Other accessories

3 mm Round Beams, modeling rods, pack of 10

€6.49

These 3 mm round beams bring clean, uniform rod stock to scratch building, detailing and structural model work. The pack contains 10 matching rods, giving builders a ready supply for repeated cuts, shaped inserts and custom additions where a consistent round section matters across the whole build. The white beam material suits a wide range of workshop tasks, from internal bracing and spacers to visible framework and fine surface additions. The 3 mm diameter is substantial enough for structural accents yet still manageable for careful trimming, fitting and placement on scale scenes or custom assemblies. Straight rod stock also helps when a project needs repeated lengths with the same profile, keeping fabricated parts visually consistent. In mixed-material builds, round beams can support mock mechanical parts, railings, supports or stand-off elements without forcing a change in section shape. On the bench, these rods fit naturally into custom model projects, diorama structures and one-off modifications that call for measured, repeatable material. They also suit hobby work where standard beam stock is easier to adapt than searching for a preformed part in the exact size needed.

Other accessories

3mm U Plastic Beams, Model Building Supply, 5-Pack

€7.29

These 3 mm U-shaped plastic beams bring clean geometry and repeatable structure to model building work that calls for narrow channel sections. The pack contains 5 matching white beams, making it easier to plan parallel runs, mirrored layouts or multiple support points within the same build. The U-profile gives each beam an open groove that can be used where parts need to sit in line, slide into position or follow a defined edge. That shape suits scratch-building tasks such as framing, guides, rails and custom supports, while the white finish provides a neutral base for visible sections or later painting. The slim format also helps when space is limited and a full solid strip would take up too much room. Used as trim, reinforcement or a construction connector, each beam adds a crisp, technical look to detailed assemblies. On workshop tables, diorama projects and custom model modifications, these beams support accurate, repeatable placement across small-scale structures. The 5-piece set also leaves room for test fitting, matched left and right sections or extending the same profile through several areas of a build.

Model-making adhesive

CA Cement Easy Sanding, model adhesive, 3 g

€7.191 kg = €2,396.67

CA Cement Easy Sanding is a cyanoacrylate adhesive for model making, supplied in a 3 g tube for small, controlled applications on parts, seams and contact points. The Easy Sanding formula suits builds where the joined area may be finished after bonding, keeping assembly work aligned with later surface preparation. This adhesive is a liquid, colourless mixture of polymers dissolved in esters and is intended for careful use on hobby model assemblies. The tube format supports close placement on narrow joins and detail sections where excess adhesive can get in the way of clean results. Storage at 2-8°C helps protect the cement from light and moisture sensitivity noted for this formula. The safety data identifies ethyl-2-cyanoacrylate as the main component and classifies the cement as irritating to skin and eyes and capable of irritating the respiratory tract. On the workbench, the small tube size fits repair jobs, detail attachment and short assembly sessions without taking much space among other modelling supplies. Use belongs in well-ventilated areas, especially when handling fine parts at close range and preparing surfaces that will be sanded after the bond has set.  Warning! Not suitable for children under 14 years.

Model-making tools

Craft Spatula Width 20mm, model tool, POM

€3.39

The Craft Spatula Width 20mm is a model tool for mixing and applying paints with a broad 20 mm working edge and a newly shaped blade. That shape gives steady contact when colour is spread across a palette or guided onto small parts, helping keep application controlled during detail work. Made from POM, a polyacetal resin, the spatula is specified for resistance to water and chemical damage. This material choice also supports use with epoxy cement and putty, so the same tool can move between paint preparation, adhesive handling and surface filling without changing tools. The flat blade and angled front edge suit lifting, spreading and smoothing soft modelling materials in measured amounts. On the workbench, the long handle keeps the grip clear of wet paint and filler, while the hanging hole makes the spatula easy to store within reach. It fits naturally into finishing tasks such as mixing small batches, applying filler to seams and spreading cement with a controlled edge.  Warning! Not suitable for children under 14 years.

Model-making tools

Paint Mixing Jar 46 ml, hobby paint storage jar

€3.79

This 46 ml paint mixing jar brings measured paint preparation and tidy storage into one compact workshop essential. The clear container shows the fill level at a glance, while side measurement markings support consistent ratios when mixing colours or thinner for model finishing. A large ribbed screw cap gives a firm grip when opening and closing the jar, and the wide mouth makes it easier to fill, stir and decant paint during bench work. The glass body suits repeated use for holding custom colour mixes between sessions, whether the task is brush painting small details or preparing a batch for later application. Its transparent format also helps keep mixed shades identifiable without opening the container each time. On the workbench, the jar sits neatly alongside brushes, palettes and other finishing tools without taking much space. It fits naturally into model painting routines where accurate measuring, temporary storage and clean handling matter from one session to the next.

Model-making tools

Paint Mixing Jar Mini Square 10ml Hobby Bottle

€2.89

The Paint Mixing Jar Mini Square 10 ml brings compact paint handling to the modelling bench with a clear small-format container and a ribbed screw cap that closes the jar securely after mixing. Its square profile keeps the footprint tidy on crowded work surfaces, while the transparent body makes colour and fill level easy to read during paint preparation. The 10 ml volume suits small custom batches, touch-up colours and leftover mixes that need to be kept together for the next stage of a build. Flat sides make the jar easy to hold while pouring or transferring paint, and the wide, stable base helps it stand neatly beside brushes, pipettes and thinner bottles. The mini format also supports organised storage when several shades are prepared for one model, because each mix can be kept in its own clearly visible container. The screw cap allows mixed paint to be closed between sessions instead of being left exposed on an open palette. On a workbench used for brush painting, detail correction or airbrush preparation, the compact square jar keeps small quantities manageable and close to the task at hand. It also works well as a dedicated container for test mixes before a final colour is applied to a bodyshell, figure or scale detail.

Other accessories

Pla-Paper 0.2mm B4, model sheet, 3 white sheets

€12.49

Pla-Paper 0.2 mm B4 is a thin sheet material for model making, scratch-building and custom detailing. The 0.2 mm profile supports light surface work where a full plastic block would be too heavy or too thick, while the B4 format of 257 x 364 mm leaves room for larger patterns, long trim sections and multiple smaller cutouts on the same sheet. The pack contains 3 white sheets, which helps when a build calls for mirrored parts, repeat pieces or a second attempt after a test fit. The white surface makes pencil marks, traced outlines and template lines easy to read during measuring and cutting. In workshop use, the material suits panel overlays, interior details, backing pieces and other flat components that need a clean, uniform look. The thin format also makes it practical for layering where extra surface definition is needed without adding much bulk. On the bench, one sheet can be kept for templates while the remaining 2 are reserved for final parts, helping maintain consistency across a conversion or repair. For hobby projects that rely on hand-cut shapes and careful fitting, this sheet stock adds a straightforward material option for precise custom work.

Other accessories

Pla-Plate 0.3mm B4 Size, model sheet pack

€10.49

Pla-Plate 0.3mm B4 Size is a thin sheet material for model making that brings clean, uniform stock to scratch building, custom detailing and structural additions. The 0.3 mm profile suits work where a lighter layer, a surface skin or a finely trimmed insert needs to sit neatly against surrounding parts, while the B4 format opens up room for larger templates and repeated shapes. The pack contains 5 white sheets, giving a steady supply for multi-stage fabrication or for keeping matching material across one project. Flat sheet stock like this supports measured marking, straight cuts and controlled shaping for panels, covers, liners and other custom-made sections. In model workshops, a thin plate can be used to create overlays, refine contours or add new surfaces where molded parts do not provide the required form. The white finish also makes pencil lines, cut marks and layout planning easier to read during preparation. On the bench, the larger B4 size helps when drafting several parts from one sheet or when testing a full pattern before trimming it down. It fits naturally into scratch-built projects, conversions and repair work where consistent thickness matters across every added section.

Other accessories

Pla-Plate 0.5mm B4 Size, styrene sheet pack

€11.49

Pla-Plate 0.5mm B4 Size is a styrene sheet set for model making and custom fabrication, combining a thin 0.5 mm profile with a large B4 format that suits clean, measured work on flat parts and added detail. The white sheets present a plain surface that can be marked out clearly before cutting, helping planned shapes stand out during layout and trimming. With 4 sheets in the pack, the set supports repeated parts, spare sections and larger scratch-built elements without mixing formats. The thin stock is suited to overlays, panels, facings and other shaped components where a full block material would be too heavy or too thick. In workshop use, the broad sheet area leaves room to arrange several templates on one board, while the consistent thickness helps matching parts sit evenly across a build. The flat form also makes it practical for testing fit before committing to a final shaped section. On scale models, dioramas and custom hobby projects, the sheets can be cut into body panels, interior sections, structural inserts or visual detailing where plain stock is needed. The format also suits craft benches that need a uniform material for prototyping, pattern work or small-batch part making across several stages of a project.

Other accessories

Pla-Plate 1.0mm B4 Size, styrene sheet set

€11.29

Pla-Plate 1.0mm B4 Size is a sheet material for model making, scratch-building and custom fabrication, giving builders a clean white styrene surface that can be marked, cut and shaped for tailored parts. The 1.0 mm thickness adds substance for structural sections and larger panels, while the B4 format leaves room to plan several pieces on one sheet before trimming. This pack contains 2 matching sheets, which helps when a build needs mirrored parts, repeat sections or spare material for test fitting. The plain sheet format suits body modifications, interior panels, scenery elements and workshop-made details where standard kit parts do not cover the required shape. White styrene also makes pencil lines, templates and edge work easy to see during measuring and cutting. Because the material arrives as flat stock, it can be adapted to many model-making tasks that depend on exact dimensions rather than pre-formed shapes. On the bench, the larger B4 area supports careful layout work before the first cut, whether the goal is a single broad panel or several smaller components from one sheet. In diorama and conversion projects, the 2-sheet pack keeps the same thickness available across connected sections and follow-up adjustments.

Other accessories

Pla-Plate 1.2mm B4 Size, plastic sheet

€13.49

Pla-Plate 1.2mm B4 Size is a flat sheet material for model making, scratch building and custom hobby fabrication. The 1.2 mm thickness gives the sheet enough substance for structural layers, shaped inserts and clean-edged cut parts, while the B4 format leaves room for larger layouts, repeated templates and broad surface sections on a single sheet. Each pack contains 2 sheets, which supports paired parts, mirrored shapes and spare material for test fitting before final assembly. The flat format suits measured marking with rulers, pattern transfer from paper templates and trimming into panels, strips or backing pieces for conversions and diorama details. In workshop use, the larger sheet area helps reduce seams on wide sections and leaves more freedom when planning multiple components from one board. On the bench, the sheets can serve as base stock for custom body details, interior panels, display elements or structural additions where a consistent 1.2 mm profile matters. For hobby projects that call for clean geometry and repeatable cuts, the 2-sheet pack provides practical material for both planning and final execution.

Other accessories

Plastic Beams 3mm H, model supplies, white

€7.29

Plastic Beams 3mm H is a white model supplies set built around a simple, exact format: 5 matching beams with a 3 mm H profile. That defined section makes the pack useful wherever a build calls for repeatable structural pieces, whether for replacement work, extensions or custom fabrication. The straight beam shape supports clean alignment across adjoining sections, and the white colour keeps visible additions consistent with lighter layouts and finishes. Because all 5 pieces share the same profile, the pack suits measured planning where several supports, rails or spacers need to match one another closely. The format also lends itself to cut-to-length work in scratch-building and conversions, where a uniform section is more useful than mixed offcuts. As model supplies, these beams fit naturally into workshop stock for ongoing projects that need spare structural material on hand. On the bench, the set works well for refining a single build or keeping matching material ready for later repairs. The compact pack of 5 beams also suits hobby drawers and parts organisers, where clearly defined white sections are easy to sort and retrieve for the next modelling task.

Model-making adhesive

Polycarbonate Body Reinforcing Cement, RC adhesive

€18.291 kg = €182.90

This reinforcing cement is made for R/C model polycarbonate bodies and focuses on one clear task: adding support where a bodyshell needs repair or extra backing. The 100 ml tube and included plastic spreader create a straightforward setup for applying cement across inner surfaces, seams or damaged sections inside a shell. The formula is intended for polycarbonate, the material widely used for lightweight R/C bodyshells that flex during running and handling. Spread onto the inside of the shell, the cement can be worked over stress points, crack lines or worn areas where reinforcement is needed. The flat spreader helps guide the material into a broader layer instead of a narrow bead, which is useful when covering a larger patch zone or building support around a split. This makes the cement a practical workshop supply for maintenance between running sessions or during a body refresh. On the bench, it fits naturally alongside routine bodyshell care such as checking impact points, strengthening corners and restoring areas that have taken repeated flex. For hobby use centered on keeping a favourite shell in service, this cement supports clean repair work on polycarbonate R/C bodies with a tool included for direct application.  Warning! Not suitable for children under 14 years.

Other accessories

1:14 Highroof 56375, model parts, cab section

€28.99

Highroof 56375 brings a 1:14 cab section into truck model work with unpainted molded parts that show the main front body shape, a rectangular window opening and defined exterior panel lines. The sprue layout keeps the individual sections organised during preparation and helps separate the main shell from the smaller trim elements before fitting and finishing. The set centres on the upper cab area and front face rather than a complete vehicle, making it suited to replacement work, restoration projects or a custom body configuration built around a high-roof truck look. Separate curved front pieces add another construction stage at the nose of the cab, where alignment and surface preparation shape the final appearance. Molded attachment points support placement of the parts during assembly, while the plain white finish leaves the surfaces ready for primer, paint and detailing matched to the chosen model scheme. On the bench, the parts support measured trimming, dry fitting and paint planning before final installation on a compatible build. In a workshop setup focused on truck models, the 1:14 scale and cab-specific form make this set a practical basis for replacing worn body sections or developing a different front-end style.  Warning! Not suitable for children under 14 years.

Other accessories

3 mm Round Beam, modelling material, clear rods

€6.49

These clear round beams bring a precise 3 mm profile to model making, scratch-building and custom craft work. The transparent finish keeps the structure visible without adding colour, which suits frames, supports, guides and detail parts that need a clean technical look. The pack contains 5 beams, giving consistent material for repeated components or several separate modifications within one build. The soft material supports cutting and adapting to the required shape, which helps when a project calls for custom lengths or fitted internal structure. In small-scale scenes, transparent rod stock can be used where spacing, alignment or light transmission matters. The round section also suits mechanical mock-ups, educational constructions and hobby experiments that rely on a uniform diameter. On the workbench, these beams fit naturally into projects that move beyond standard kit parts. They can support one-off details, replacement sections or original structures built from raw material, whether the goal is a cleaner finish, a visible framework or a custom display element.

Other accessories

3mm Pipe Beams, model building tubes, white

€8.39

These 3 mm pipe beams bring a clean, technical building element to model making, with a white finish and a hollow tube profile that suits structural additions, custom fabrication and replacement work. The 6 matching pieces give a consistent starting point for projects that need repeated lengths, aligned detailing or uniform tubing across a build. The cylindrical form makes these beams useful wherever a round section is needed instead of a flat strip, and the open ends support applications where the tube shape itself is part of the look or function. In scratch-built assemblies, they can serve as spacers, framework sections or visible technical accents. The white material also works well as a neutral base for further finishing, while the simple beam format keeps cutting, fitting and combining straightforward within a wider model workshop setup. On the bench, these tubes suit careful modification work, small repairs and custom detailing on scale scenes or vehicle projects. They also fit neatly into parts storage for repeat use when a build calls for matching round beams rather than mixed offcuts.

Other accessories

3mm Square Beams, plastic model supply, 10-pack

€6.99

These 3 mm square beams provide a clean, consistent starting point for scratch-building, structural detailing and custom model work. The pack contains 10 white styrene strips, giving a ready supply of matching sections for measured cuts, repeated lengths and neat framed shapes on the workbench. The square profile makes these beams useful wherever straight edges and even corners matter. Styrene can be adapted for supports, braces, spacers and small fabricated sections, whether the task involves extending a structure, refining an interior layout or adding custom reinforcement. Because all 10 strips share the same 3 mm format, planning mirrored parts and keeping dimensions consistent becomes easier across a series of cuts. The white finish also helps pencil marks and cut lines stay visible during measuring and trimming. On a hobby bench, the beams fit naturally into projects that call for custom geometry rather than pre-formed parts. They can be prepared in short sections for compact details or kept longer for rails and frame runs, making them a practical material choice for ongoing model modification and scratch-built construction.

Other accessories

5 mm Pipe, Plastic Beams accessory, white

€8.39

These Plastic Beams 5 mm Pipe parts add a clean tubular element to custom model work, with a white finish and hollow form that suit structural accents, spacing tasks and lightweight scratch-built details. The set contains 5 matching pieces, making it useful where the same diameter needs to repeat across a build. The 5 mm format gives a clear reference point for planning fit and proportion in technical scenes, vehicle interiors or workshop-style assemblies. The open circular ends allow the tube shape to read clearly in exposed layouts, and the smooth surface supports neat trimming and placement. White colouring stands out well during measuring, test fitting and marking, which helps when several small components are being arranged at once. As a model supply rather than a finished display piece, these beam pipes can be cut, positioned or combined according to the needs of the build. On the bench, the set suits restocking a parts box, refining a conversion or adding simple pipework to a diorama section. It also works for replacing worn sections in an existing project where matching diameter and a tidy tubular profile matter.

Other accessories

5 mm Plastic Beams, model building accessory

€7.29

These white plastic beams provide straightforward building stock for model making, custom fabrication and scratch-built details. The pack contains 5 pieces, giving matching material for repeated sections, parallel supports or small structural additions where a consistent profile matters on the bench. The 5 mm beam format supports measured cutting and planning when a build calls for clean lengths instead of improvised offcuts. Straight stock like this can be used to form internal bracing, visible framework, edging or custom add-ons in hand-built scenes and conversions. The white material also offers a neutral base for sanding, trimming and finishing to match the surrounding assembly. Because all 5 pieces share the same format, it is easier to prepare mirrored parts or repeated elements that need the same visual rhythm. On a worktable, these beams fit naturally into ongoing model projects, whether the task is replacing a missing section, extending a structure or adding fresh detail to a custom build. They also make practical workshop stock for keeping core shapes ready between larger fabrication steps.

Other accessories

5 mm Round Beams, model building rods, white

€6.49

These 5 mm round beams bring clean geometry to model building, scratch construction and custom detailing. The white finish keeps layout lines visible during marking and trimming, while the uniform round profile supports repeatable sections for braces, spacers and shaped additions. Each pack provides 6 beams for builds that need matching diameters across several points, whether the task is extending a structure, adding internal supports or preparing duplicate parts. The rod format suits measured cutting, sanding and fitting, making it useful for workshop prototypes as well as fine visual detailing. In scale projects, round stock like this can be worked into frames, mounts or cylindrical features where a square strip would not match the intended form. On the bench, these beams fit naturally into careful planning and test fitting before final placement. They suit custom model work, conversions and one-off fabrication where consistent 5 mm material helps keep proportions even from one section to the next.

Other accessories

5 mm Square Beams, model building strips

€6.99

These 5 mm square beams give scratch-built models and custom scenes a crisp, regular profile that is easy to plan around on the workbench. The white styrene material suits measured cutting, shaping and joining, whether the goal is a simple frame, a structural brace or a clean-edged detail added to a larger build. The square section helps keep corners consistent when building supports, borders or fabricated components that need a uniform look across repeated parts. With 2 matching beams in the pack, the same profile can be carried through paired rails, parallel members or mirrored details without changing stock midway through the job. The long strip format also leaves flexibility for either full-length applications or several shorter sections, depending on the layout of the model. In architectural scenes, workshop builds or vehicle conversions, the material can be adapted to visible trim as well as hidden reinforcement. On a hobby bench, these beams fit naturally into scratch-building tasks where raw material matters as much as the finished shape. They suit diorama structures, custom body details, internal framing and other model-making work that starts with accurate stock and careful hand finishing.

Model-making tools

Builder's 8 Screwdriver Set, hobby tool kit

€28.49

Builder's 8 Screwdriver Set gathers the core hand tools for fine model work into a compact 8-piece format. The set combines 3 Phillips screwdrivers, 2 flat screwdrivers, 2 nut drivers and 1 hex wrench with a detachable grip, giving small fasteners and fittings a single, organized tool station for bench use. Each head can be paired with the grip as the task changes, which suits the stop-and-start rhythm of RC maintenance, miniature assembly and detail adjustment. The mix of tip styles supports common fastening points found in hobby builds, while the separate nut drivers and hex wrench extend the set beyond standard screw turning. Red holders keep the individual tools visually sorted, so the required head can be picked out quickly instead of being mixed loose in a drawer. The clear carrying case keeps the full set together for storage and transport between shelf, toolbox and work area. On a model bench, the set supports careful fitting, small corrections and repeat adjustments without taking up much space. It also works well as a dedicated companion for ongoing RC and scale model projects where several fastener types appear across one build.

Model-making adhesive

CA Cement & Primer Set, model adhesive, 3g

€13.491 kg = €4,496.67

This CA Cement & Primer set combines a 3 g tube of adhesive with a 3 g primer pen for bonding model parts made from PP, PE, POM and EVA. The quick-drying primer is brushed onto both cementing surfaces a few times, preparing materials that are often difficult to join with standard model cement alone. After the primer has dried, a small amount of CA cement is applied to 1 surface, and the parts are attached soon after for the strongest effect. That sequence gives the set a clear working method rather than a trial-and-error approach, which is especially useful on tracks, structural parts and other low-adhesion components. The primer is intended only for PP, PE, POM and EVA parts, and it is not needed for materials that can be attached only with CA cement. The set can be used on Mini 4WD series parts, Educational Construction series components, Military Miniature tracks and other difficult-to-cement model materials. On the workbench, it supports repair jobs, replacement parts and precise assembly steps where a fast bond and the right surface preparation matter.

Model-making tools

Cutting Mat α A3 Half, hobby cutting mat, blue

€18.29

The Cutting Mat α in A3 half format brings a compact 450 x 145 x 2 mm work surface to model benches where long, narrow space matters as much as clean measuring. Printed grids, angle guides, R curves and reference scales give rulers and hobby knives clear alignment points, while the translucent blue finish keeps markings easy to read during close detail work. Made from low-odor olefin resin, the mat is built as a practical bench surface for trimming, marking and layout tasks around scale modelling and craft work. The printed face combines standard measurement aids with curved and circular references that help position parts, tape and sheet material before the blade touches down. A plain reverse side adds a second usable face when a cleaner surface is needed for other bench steps. The A3 half shape also suits narrow shelves, portable tool setups and smaller workstations where a full A3 mat would take more room than necessary. During masking work, the dedicated tape-cutting lines help prepare repeated strip widths with less guesswork. For scoring styrene, trimming decals or cutting paper against a metal ruler, the long 450 mm edge gives useful reach while the 145 mm depth stays easy to place beside paints, tools and in-progress assemblies. The result is a focused cutting surface sized for regular hobby use rather than a full-desk layout.

Other accessories

Foam Board 2mm B4, craft sheets, 4 pieces

€14.69

This pack of foam board sheets brings a clean, practical base material to model making, layout work and craft builds. Each set contains 4 white sheets in B4 format, with a 2 mm thickness and a sheet size of 257 x 364 mm, giving a broad surface for measured cuts, layered shapes and lightweight panels on the workbench. The slim foam board structure suits tasks where a flat board is needed without the bulk of thicker stock. It can be marked out for templates, trimmed into custom forms, or used as a backing layer for presentation pieces and scenery sections. The plain white finish keeps the surface neutral for sketching, covering, painting or combining with printed references and other hobby materials. Straight-cut edges also make it easier to align repeated sections and keep corners tidy during layout work. On a model bench, the sheets can serve as a base for mock-ups, architectural studies, display backings or terrain elements that need a light core. In craft use, the B4 format gives enough area for larger shapes while still fitting neatly into organised storage and regular cutting spaces. Radio gear, a battery pack, a charger and paints are not required for use with this foam board.  Warning! Not suitable for children under 14 years.

Other accessories

Foam Board 5 mm, craft board sheets, B4 size

€12.49

This foam board set brings clean edges, low weight and useful thickness to model making and craft work. The pack contains 2 white sheets in B4 size, each measuring 364 x 257 mm, with a 5 mm profile that gives flat layouts more structure and presence. Whether used for backing panels, mock-up walls or simple display surfaces, the format is easy to integrate into bench projects where straight cuts and consistent sizing matter. The lightweight construction, listed at 60 g per sheet, keeps handling straightforward when sections need to be moved, checked or combined. The 5 mm depth supports layered builds, raised details and simple stand-up forms without relying on heavy board stock. The white surface also works well for drawn guide lines, trimmed shapes and clean visual contrast around painted parts, printed graphics or small scenic elements. In workshop use, the pair of matching sheets gives enough material for mirrored sections, test pieces or a main panel with spare stock kept aside. On a hobby table, the boards suit diorama bases, presentation backdrops and quick structural mock-ups. They also fit craft tasks that call for a light panel with a larger working area than small card pieces, while the B4 format remains easy to store between sessions.

Other accessories

Pla-Board 2mm B4, modeling sheet, 2 pcs

€13.49

Pla-Board 2mm B4 is a white modeling sheet set for scratch building, fabrication and custom hobby work. Each pack contains 2 sheets, and each sheet measures 257 x 364 mm in B4 format, giving a large, consistent surface for planning parts, cutting shapes and building clean structural sections for models or craft projects. The 2 mm board thickness supports work that calls for more substance than a thin facing layer, such as internal supports, formed panels, dividers or custom-built housings. The white surface is easy to mark during layout work and keeps edges, cut lines and fitted shapes clearly visible while parts are being prepared. Across diorama construction, model modification and general hobby fabrication, the sheet format leaves room for larger patterns as well as several smaller components taken from one board. On the workbench, the pair of matching sheets helps keep material consistent across repeated parts or mirrored sections. The broad B4 size also suits template transfer, mock-up building and one-off custom pieces where standard kit parts do not cover the required shape or dimension.

Other accessories

Pla-Board 3mm B4, model building sheet, white

€9.49

Pla-Board 3mm B4 is a white model-building sheet made for scratch construction, custom fabrication and clean structural work in hobby projects. The 3 mm thickness gives the board substance for parts that need more presence than thin sheet material, whether used for bases, spacers, panels or shaped inserts. The B4 size measures 257 x 364 mm, leaving enough surface for larger cut sections, repeated templates or several smaller components from one board. The flat format supports careful measuring before cutting, and the plain white surface keeps pencil marks, layout lines and edge checks easy to read during fabrication. Supplied as 1 board, it fits focused modification work where a single panel is the right starting point. On the bench, the sheet can be trimmed into straight strips, shaped into custom sections or used as a backing layer for diorama structures and model details. It also suits repair and conversion tasks that call for a clean, uniform board with consistent 3 mm thickness across the full panel.

Other accessories

Plastic Beams 3mm L, model building spare parts

€6.69

Plastic Beams 3mm L brings clean white structural stock into model building work where straight lines, repeatable cuts and a consistent profile matter. The set contains 6 separate beams, each made for trimming, fitting and integrating into custom assemblies, repairs or added framework on hobby builds. The 3 mm beam format suits jobs that need narrow stock rather than broad sheet material. It can be cut to length, aligned as a brace, or used to form small supports and structural sections inside a build. The white finish keeps the material easy to see during measuring and placement, which helps when matching lengths across repeated parts. Because the beams are supplied as individual lengths, the set also works well as workshop stock for ongoing conversions and detail work. On the bench, these beams support careful scratch-building, reinforcement of existing structures and the addition of clean linear details to model scenes or custom assemblies. They are equally useful when replacing worn sections, testing a new layout or keeping matching material ready for the next stage of a build.

Model-making tools

RC Pit Bag Large with 3 Inner Storage Boxes

€79.99

The RC Pit Bag Large brings structured transport to race days with a padded rectangular bag and 3 removable inner boxes sized to the larger TRF501X package format. That layout keeps machines and support equipment grouped in separate sections, so bench essentials stay easier to sort when moving between storage, travel and trackside setup. Each inner box is described as durable enough for heavier contents such as batteries and chargers, which makes the set useful for carrying dense RC equipment rather than only lightweight spares. The inner boxes slide into the main bag from the side and help maintain the bag's internal form while dividing the load into clear sections. Carry handles on the boxes add another practical step at the workbench, since a single section can be lifted out instead of unpacking the whole bag. The outer bag combines navy blue fabric with blue grip belts and fasteners, plus Tamiya and TRF logos that give the case a workshop and race-team look. On a club day, the bag can move from shelf to car to pit table with machines and support gear kept together in one box-shaped case. Between runs, one inner box can sit beside the setup area while the remaining sections stay packed, helping the transport routine stay orderly when equipment needs to move quickly.

Model-making tools

RC Pit Bag Medium, carrying bag with 2 inner boxes

€69.99

The RC Pit Bag Medium brings order to race-day transport with a nylon canvas carry bag and 2 included inner boxes sized for common 1/10 scale RC equipment. With outer dimensions of 28 x 47 x 30 cm, it creates a compact footprint for moving a buggy or touring car together with the gear that usually travels alongside it. The 2 inner boxes measure 44.5 x 25.7 x 14 cm each and divide the interior into clear storage zones, so models, tools and running essentials can be packed with less mixing during travel. The bag format is intended for 1/10 scale off-road buggies and touring cars, giving those chassis types a dedicated transport option instead of loose loading in larger cases. A zippered opening around the top and side gives broad access to the main compartment, which helps when lifting equipment in and out between runs. Wraparound webbing straps support the bag body while carrying heavier RC gear. The inner boxes are also stated as durable enough to hold heavier contents such as batteries and chargers. At the track, the layout supports a cleaner setup on the pit table because the main car and supporting equipment can be unpacked from one place. Between workshop storage, car travel and casual racing sessions, the bag keeps frequently used RC equipment together in a format built around transport and quick access.

Model-making tools

TRF Storage Box, 8-compartment case set

€19.99

The TRF Storage Box (8-Comp) (3) brings small-part organisation into a compact format built around 3 separate 8-compartment storage cases and 1 outer case. Together they create 24 independent sections for screws, nuts and similar hardware, so mixed fasteners can be separated by size, type or current project while staying in one place. Each inner case can be arranged as its own sorting unit inside the larger holder, which helps keep frequently used parts grouped for bench work, RC maintenance or transport to a race meeting. The semi-transparent material gives a quick view of the contents before opening, reducing time spent checking each section by hand. The outer case measures 186 x 96 x 39 mm, a footprint that fits easily into a tool bag, drawer or field box while still carrying multiple categories of small components. On the workbench, the compartment layout supports cleaner parts handling during builds, repairs and routine upkeep. In a pit setup or storage drawer, the 3 removable cases make it easier to separate hardware for different models, spare sets or tuning tasks without loose pieces shifting into one shared space.  Warning! Not suitable for children under 14 years.

Model-making tools

A3 Cutting Mat, hobby work surface, 450 x 320 mm

soon available again

This A3 cutting mat creates a clean, measured work zone for model building and paper craft, with a 450 x 320 mm surface that sits slightly larger than A3 paper. The green 2 mm mat gives knives and similar tools a dedicated base while helping keep the desk underneath clear during trimming, marking and layout work. Its 3-layer structure combines a harder inner layer with softer outer layers. That construction is designed so cut ends remain less conspicuous, and it also helps the blade stay sharp for longer during repeated use. The front side is printed with a dense set of practical guides, including grids, angled lines, R curves and circular lines. These markings support alignment, spacing and repeatable shapes when preparing sheet material, planning cuts or checking symmetry on small parts. The reverse side uses a plain solid color, which changes the mat from a measured cutting surface into a simpler backing for other bench tasks. On a hobby desk, that makes it easy to move between precise knife work, template placement and general craft handling without changing the work area. The format suits model supplies, paper sheets and other flat materials that benefit from a stable, clearly defined surface.

Other accessories

Cotton Swab Tria.small, hobby tool, 50 pieces

soon available again

The Cotton Swab Tria.small is a compact hobby tool for precise cleanup and controlled application work. Each swab uses a narrow cotton tip measuring 10.5 mm in length and 3 mm in width, a format that helps reach confined sections where a broader tip would cover too much area. The slim white stick carries cotton on both ends, giving 2 working tips per swab and 100 usable ends across the 50-piece pack. This layout supports short, exact motions when handling small amounts of material, lifting residue from edges or working around recessed details. The tria.small designation points to a compact tip profile, making the swabs especially suited to fine-scale maintenance and finishing tasks where contact needs to stay localized. On a workbench, the narrow tip can be used for careful touch-up preparation, gentle surface cleaning or controlled work around corners and small openings. In model building and finishing routines, the 50-count pack provides a practical supply for repeated detail sessions without taking much space in the tool area.  Warning! Not suitable for children under 14 years.

Other accessories

Cotton Swab Triangular 50pc Hobby Applicators

soon available again

These triangular cotton swabs are made for model work where a standard household swab quickly loses its edge. The tightly spun cotton tips keep their form during painting, decal application and panel lining, giving steadier contact on small surfaces and more control around raised details. The pointed profile helps guide pigment, lining fluid or decal pressure into corners and along narrow sections that are awkward with a rounded tip. Industrial strength construction means the cotton is less likely to fray when wet or when dipped in solvents, so the working edge stays cleaner through repeated passes. The pack contains 50 swabs, ready for regular bench use across touch-ups, weathering and cleanup steps. Tip dimensions shown in the product data are 10.5 mm in length, with widths of 3.4 mm and 2.3 mm for the two illustrated pointed profiles. On a painted bodyshell, the swabs can press decals down over panel lines and contours with a lighter, more exact touch. During weathering, they help place rust stains, blend effects in confined spots and carry Weathering Master Set colours onto selected areas without flooding the surrounding surface.  Warning! Not suitable for children under 14 years.

Other accessories

Display Case C, model display case for 1:20, 1:24

soon available again

Display Case C gives finished scale models a dedicated presentation space with clear panels, a black molded base and proportions matched to 1:20 racing cars and 1:24 sports cars. The transparent cover keeps the focus on paint, markings and body shape while the dark base creates a clean visual frame around the model. The inner dimensions measure 247 x 133 x 92 mm, giving compatible builds a defined enclosure that suits shelf display, cabinet placement or a workbench setup. Outer dimensions of 260 x 144 x 105 mm make the overall footprint easy to plan when arranging several finished models side by side. The molded base can be modified to suit individual display requirements, which helps when a build calls for a particular mounting position or presentation layout. On a desk, in a hobby room or inside a display cabinet, the case turns a completed build into a focused centerpiece instead of leaving it exposed on an open surface. It suits builders who want a clear, measured way to present a finished racing car or sports car model after painting and final detailing.

Other accessories

Display Case D, display case for 1:12 motorcycles

soon available again

Display Case D gives finished scale models a clean presentation with transparent panels and a black base that frames the silhouette clearly on a shelf, desk or in a cabinet. Sized for 1:12 motorcycles and also suitable for 1:24 small cars, it creates a defined space that keeps the focus on the model itself rather than the surroundings. The case measures 260 x 144 x 145 mm on the outside, with inner dimensions of 247 x 133 x 132 mm for the displayed build. That sizing supports compact vehicle subjects without wasting space around them, which helps smaller models sit neatly within the enclosure. The transparent construction keeps paintwork, markings and overall proportions visible from several sides, while the dark base gives bright liveries, chrome parts and wheel details a stronger outline. Placed in a hobby room, office or display cabinet, the case suits finished motorcycle builds that deserve a dedicated setting after assembly and painting. It also works for smaller 1:24 cars when a single model needs a tidy standalone presentation with clear visibility and a measured footprint.  Warning! Not suitable for children under 14 years.

Other accessories

Display Case F, display case for 1:35 military

soon available again

Display Case F gives larger 1:35 military models a clean, enclosed setting that keeps the focus on the finished build. The clear cover and black molded base create a strong contrast around paintwork and surface detail, while the overall outer size of 360 x 168 x 145 mm suits shelves, desks and display cabinets. Inside, the usable space measures 350 x 158 x 131 mm, which fits substantial 1:35 subjects rather than only compact vehicles. The format is intended for military builds and is sized for models such as a Challenger 2 or a Type 90 tank with mine roller, as stated in the product data. The base is molded in plastic and can be modified to suit a chosen layout, which helps when positioning a finished model or adapting the presentation to a specific scene. The transparent cover keeps the silhouette visible from side to side instead of closing it off with a solid surround. Placed in a hobby room, office or cabinet, the case gives a completed armored vehicle a dedicated space instead of leaving it exposed on an open shelf. It also suits builders who want a neater way to present a finished 1:35 military subject after painting, detailing and final placement on the base.

Model-making tools

Paint Jar Stand, hobby paint organizer with clips

soon available again

The Paint Jar Stand brings order to a busy painting bench with a rotating 2-tier layout that keeps labels in view and colors easy to reach. As the trays turn, paint selection becomes quicker and the workspace stays more focused during detail painting, touch-ups and longer finishing sessions. Each tray is shaped for clear jar storage, with capacity for up to 7 acrylic mini jars or 9 enamel jars. The stand measures 135 mm across and 220 mm high, using vertical space instead of spreading jars across the table. A central holder at the top keeps brushes upright, so paint and tools stay gathered in one place. Small grooves along the tray edges accept the 4 included alligator clips, which can hold newly painted parts above the tray while surfaces dry. The stand is designed for stable tabletop use, and the stated maximum load is 1.5 kg for the stand. On a model bench, the rotating trays help bring the needed color forward instead of shifting rows of jars by hand. During painting breaks, clipped parts can stay raised and separated while brushes return to the center holder, keeping the next step ready without crowding the work area. Paints are not included.  Warning! Not suitable for children under 14 years.

Model-making adhesive

Tamiya Cement Low Odor, model adhesive, 40 ml

soon available again

Tamiya Cement Low Odor is a model adhesive in a square 40 ml bottle, made for plastic model assembly and suited to styrene plastic. The water-based formula pairs focused material compatibility with a lower-odor handling profile, while the brush built into the lid keeps the applicator ready as soon as the bottle is opened. The square bottle shape sits neatly on a work surface and is easy to position beside parts, cutters and sanding tools during a build. Because the brush is stored in the cap, adhesive can be lifted and placed directly onto seams, edges and small contact areas without reaching for a separate tool. That setup helps when aligning body panels, interior sections or other styrene components that need careful placement before joining. The 40 ml volume also suits repeated use across multiple assembly stages instead of a single quick repair. On the bench, this adhesive fits the steady rhythm of model construction, whether attaching small detail parts or working along longer joins on larger sections. It suits builders who want a dedicated cement for styrene kits and a bottle format that keeps application simple, tidy and close at hand throughout the build.  Warning! Not suitable for children under 14 years.

Model-making tools

TRF RC Tool Bag, tool case, polyester storage

soon available again

The TRF RC Tool Bag keeps workshop essentials together in a compact soft case built for hobby transport and bench organisation. Black polyester gives the bag a cushioned structure around stored contents, and the 310 x 200 x 60 mm format suits regular movement between storage, work area and trackside setup. Inside, the layout focuses on keeping hand tools and small accessories sorted instead of loose. An internal divider separates contents into sections, while a touch fastener tape strap helps hold larger tools in place. The lid adds a mesh pocket for flat accessories, and elastic loops create dedicated spots for slim pieces such as drivers, pens, cables or similar workshop gear. A zip-around closure opens the case wide, making the contents easier to see and reach when adjustments need to happen quickly. The size is stated for TRF tools and long-nose pliers, which makes the bag a practical match for RC maintenance routines, parts organisation and transport between home storage and race meetings. Printed Tamiya and TRF logos on the top complete the clean workshop look without changing the bag's straightforward storage role.

Model-making tools

TRF TC Carrying Case, hard storage case

soon available again

The TRF TC Carrying Case is a hard storage case for touring car transport when only the model needs to come along. Its black plastic card construction creates a firm outer shell, and the material is stated to resist water as well as internal oil spills, which suits workshop storage and travel to running sessions. The case is supplied as 1 carrying case and uses a compact format that keeps the focus on the car rather than a full equipment loadout. A plastic handle is built into the design, so lifting the case from shelf to pit table or from car boot to trackside takes a direct, single-hand grip. TRF and Tamiya logos appear on the top panel, giving the exterior the look of dedicated racing equipment without changing the straightforward storage function. This format fits moments when a touring car model is heading out on its own and the larger tool collection stays behind. It also works as a neat way to keep the model enclosed between sessions, with the hard case structure helping separate the stored car from dust, splashes and oily marks in a busy hobby space.

Model-making adhesive

CA Cement Quick Type 2g, instant adhesive

soon available again

CA Cement Quick Type 2g is an instant adhesive for model-making work that combines fast bonding with a compact applicator format. The light gray body, yellow-orange push button and narrow front tip create a clear handling setup for placing adhesive on small joins, edges and detail parts where a broad glue spread would get in the way. The 2 g fill suits short, precise bonding tasks rather than large-area application. A removable cap covers the tip between uses, and 2 tapered nozzle tips add a finer application option for narrow contact points. The adhesive is a cyanoacrylate formula, identified in the safety data as containing ethyl-2-cyanoacrylate at more than 75%. The mixture is liquid and colorless, with a density of 1.0 +/- 0.1 g/ml at 20 °C. This makes it suited to careful placement during assembly, repair or detail fitting in hobby builds. On the workbench, the push-button format helps keep attention on the join itself, whether attaching a small part, fixing a clean break or securing a detail piece in place. The compact applicator and fine tips fit neatly into model-building sessions where controlled adhesive placement matters as much as bond speed.  Warning! Not suitable for children under 14 years.

Other accessories

Clear Pla-Plate 0.2mm B4, model sheet, 5 pack

soon available again

Clear Pla-Plate 0.2mm B4 is a thin model-building sheet material for custom fabrication, detail work and clean transparent overlays. The 0.2 mm thickness suits jobs where a lighter profile matters, such as window inserts, covers, layered surfaces or fine scratch-built sections that need to sit close to the base structure. Each sheet comes in B4 size, giving ample area for laying out templates, tracing repeated shapes and cutting several parts from the same piece. The clear finish helps when guide lines, printed patterns or underlying edges need to stay visible while marking and trimming. With 5 sheets in the pack, matching material is available for test cuts, alternate versions and repeat parts across the same project. This makes the set useful for scale model modification, diorama detailing and general hobby fabrication where consistent thickness is important. On the workbench, the sheets can be measured, scored and cut into custom panels, inserts or protective covers for model scenes and vehicle builds. The transparent material also suits projects that call for neat alignment over drawn plans or existing components, keeping layout work easy to follow while shaping each section.

Other accessories

Clear Pla-Plate 0.4mm B4, styrene sheet pack

soon available again

Clear Pla-Plate 0.4mm B4 is a transparent styrene sheet set for model making, scratch building and custom detailing. With 4 sheets in B4 size and a 0.4 mm thickness, it gives builders a clean base for parts that need both accurate cutting and a clear finish, whether the goal is glazing, overlays or shaped panel work. The transparent material opens up uses that opaque sheet cannot cover, such as windows, lenses, shields and visible surface layers. The 0.4 mm gauge is light enough for scoring and trimming by hand, while still offering enough substance for neat edges and controlled fitting. B4 format leaves room for full-size templates, longer strips and several smaller components on one sheet, which helps when matching repeated shapes across a build. In scratch-built projects, the sheets can also be laminated, bent or cut into inserts depending on the design. On the workbench, this sheet stock suits custom vehicle interiors, aircraft canopies, architectural details and display additions that call for a transparent surface. It also works well as spare material kept alongside other modelling supplies, ready for repairs, modifications and one-off fabricated parts when a standard kit piece is not enough.

Other accessories

Clear Pla-Plate, sheet set, 0.3 mm B4 size

soon available again

Clear Pla-Plate 0.3 mm B4 is a sheet material for model making, scratch building and detailed craft work, combining a large 257 x 364 mm format with transparent stock that stays easy to mark, align and trim. The clear surface lets outlines, reference drawings and underlying shapes remain visible while parts are planned, which supports accurate transfers and cleaner fitting during custom work. With 4 sheets in one pack, the set gives room for repeated attempts, mirrored parts and spare sections without cutting immediately into the last piece. The 0.3 mm gauge is suited to thin panels, glazing-style inserts, overlays and other light-detail applications where a heavier board would be less practical. The broad B4 format also leaves space for longer strips, wider panels or several smaller components laid out on one sheet. For hobby benches that move between repair work, conversions and original builds, that larger working area helps keep cuts organised. The sheets suit tasks such as replacing worn clear sections, creating custom templates or preparing neat surface details for scale scenes and hand-built assemblies. On a cutting mat beside rulers, scribers and reference sketches, the transparent stock supports careful measuring before the first cut and tidy finishing once the shape is set.

Other accessories

Foam Board 3 mm, craft board sheets, 257 x 364 mm

soon available again

This foam board set brings clean sheet material and practical dimensions together for model making, display builds and general craft work. The pack contains 3 white sheets in B4 size, each measuring 257 x 364 mm, with a 3 mm thickness that gives flat panels and shaped sections a defined, easy-to-handle format on the workbench. The styrene foam core keeps the sheets light while still giving enough body for cutting, scoring and layering. Straight edges, backing panels, raised details and simple structural forms can be planned from a consistent sheet size, which helps when several matching parts are needed in one project. The white surface also works well as a neutral base for drawn guide lines, coverings, printed graphics or painted finishes, depending on the build. On architectural mock-ups, diorama sections, signs or presentation boards, the format supports quick layout work and tidy assembly. The 3-sheet pack also leaves material ready for test cuts, repeated shapes or separate stages of a larger hobby project, whether the goal is a clean display panel or a lightweight scenic element.

Model-making masking tapes

Masking Tape 10mm/18m Refill for Model Painting

soon available again

This masking tape refill combines a thin tape profile with strong adhesion for model painting work that calls for control at the edge. With a width of 10 mm and a roll length of 18 m, it covers repeated masking tasks on scale builds while staying easy to position along trim, panel breaks and other painted sections. The adhesive layer conforms well to uneven surfaces, which helps when the masking line needs to follow raised detail or subtle contours instead of only flat areas. The tape is made for modeling use and suits both painted and unpainted scale models, including radio control models. Its material resists paint absorption, so color stays on the surface rather than soaking through the tape edge. After painting, the tape can be lifted away without leaving unsightly marks, keeping the finish cleaner around the masked area. On the bench, this refill works for separating body colors, protecting adjacent sections during touch-ups, or defining narrow painted accents with a steady 10 mm strip. The 18 m roll also gives enough length for repeated use across several projects, whether the task is a single body shell or a series of smaller detail sections.

Other accessories

Pla-Paper 0.1mm B4, styrene sheet for model making

soon available again

Pla-Paper 0.1 mm B4 is a thin white sheet material for model making, scratch-building and detail work, with a large 257 x 364 mm format that leaves room for full templates, long strips and broad surface sections in one piece. The 0.1 mm thickness suits jobs where a light overlay or finely cut addition is needed rather than a heavier panel. The B4 size gives more continuous working area than small offcuts, which helps when laying out repeated shapes or trimming larger covers. With 3 sheets in the pack, the same material can be kept on hand for matching parts, trial pieces and follow-up adjustments during a build. The white finish also makes pencil lines and cut marks easy to place when preparing patterns or fitting custom sections. On a workbench, the sheets can be used for body details, interior panels, templates or surface skins on scale projects. They also fit general hobby tasks that call for thin, even sheet stock, whether the goal is refining an existing model or creating new parts to match a planned design.

Model-making tools

R/C Car Bag, model accessory, nylon 57 x 34 cm

soon available again

The R/C Car Bag adds a simple layer between an R/C car and the rest of the gear packed for a session. Made from nylon and sized at 57 x 34 cm, it slips over the car as a soft transport cover that helps keep dirt and residue away from a carrying case or pit bag after use. The bag uses a drawstring closure at the top, allowing quick opening for loading and a snug pull to close once the car is inside. Its flexible fabric folds flat when not in use, so it takes little room in a workshop drawer, track box or travel kit. The printed TRF branding gives it the look of a dedicated racing accessory rather than a generic storage pouch. When a body clip, small trim part or other loose piece comes away during transport, the enclosed format helps keep that part with the car instead of letting it disappear into larger luggage. It suits the moments between bench, car park and track when a used chassis needs covering before the next stop. It also works as a tidy storage layer on a shelf or in a vehicle, where the nylon surface keeps the car separate from surrounding equipment and ready for the next outing.

Model-making tools

Switch Lubricant, contact grease for model controls

soon available again

Switch Lubricant is a contact grease for model vehicles that supports electrical conductivity in control components and helps address arcing at speed controllers. The white, pasty formula is supplied in a tube with a separate precision applicator tip, creating a controlled way to place small amounts exactly where contact surfaces need treatment. The formulation is described as polyolefins with additives, giving this lubricant a grease-like consistency rather than a thin liquid flow. At 15 °C, the density is 0.9 g/ml, and the material is insoluble in water at 20 °C. The data sheet lists a drop point of 220 °C and a flash point above 200 °C. These physical properties define the material itself and distinguish it from lighter hobby oils used for other maintenance tasks. In use, the narrow tip supports careful application on compact electrical parts where excess lubricant would be unhelpful. This accessory fits naturally into regular workshop care for RC and model vehicle electronics, especially when switch contacts or speed controller contact points need targeted lubrication. Kept alongside other bench supplies, the tube and applicator tip support repeatable maintenance on small assemblies and detailed electrical hardware.  Warning! Not suitable for children under 14 years.

Model-making adhesive

Tamiya Extra Thin Cement, model cement, 40 ml

soon available again

Tamiya Extra Thin Cement with Brush 40 ml is a liquid model cement made for plastic model kits that use polystyrene. The extra thin formula is designed for precise bonding on small sections, where clean placement matters and excess adhesive can interfere with surrounding detail. With the bottle open and the brush lifted from the cap, the cement can be guided straight into fine seams and contact points during careful assembly. This cement is especially suited to detailed work on small parts that need pinpoint accuracy and finesse. The liquid consistency helps it reach tight joins instead of sitting heavily on the surface, which is useful when working around narrow edges, delicate subassemblies and closely fitted pieces. The integrated brush keeps the applicator with the bottle, so the same tool used to open it is also used to place the cement. That direct brush-to-seam handling supports steady progress during repeated fitting, joining and adjustment steps on model builds. On the workbench, the 40 ml size fits regular building sessions without taking much space beside cutters, files and paint jars. It suits tasks such as joining body sections, attaching fine detail parts and running cement along assembled seams where careful control matters most.  Warning! Not suitable for children under 14 years.

Model-making tools

Thread Forming Tap M3x0.5, modeling tool

soon available again

The Thread Forming Tap M3x0.5 brings precise thread preparation to plastic model parts, making fastening work on R/C chassis and similar assemblies more controlled at the workbench. Its 3 mm diameter and 0.5 mm pitch suit M3 threading tasks where a clean internal thread helps screws seat more consistently in pre-drilled plastic sections. This tool is supplied as 1 tap and is intended for use with the 74086 modeling drill chuck. The metal tap features a threaded cutting section, a smooth shank and a square drive end for secure engagement in a compatible holder. A plastic storage case keeps the tap together with bench tools between assembly or maintenance sessions. The stated application focuses on plastic parts, and the tool cannot be used for self-tapping screws or counter-rotating screws. On an R/C bathtub chassis, the tap can be used before final screw installation to prepare mounting points in structural sections and reduce resistance while fastening. It also suits general model-building tasks where plastic components need an M3 x 0.5 thread formed before parts are joined. Scope of delivery: 1x thread drill.  Warning! Not suitable for children under 14 years.

Model-making tools

Modeler's Punch 2mm/3mm, hobby punch tool

Factory sold out

The Modeler's Punch 2mm/3mm brings 2 commonly used hole sizes into one compact hobby tool, making it easier to prepare neat circular openings for model building, detailing and bench work. Its twin punch layout keeps the 2 mm and 3 mm cutters together, so the required size is close at hand when sheet material needs a clean, controlled cut. The working sections are metal, giving the tool the firm cutting edges needed for precise punching on small parts and material sections. A holder keeps both punch shafts aligned in one format, which helps with storage and quick access during repeated workshop tasks. This setup suits jobs such as preparing openings in thin hobby materials, refining scratch-build details or creating consistent holes across matching components. The compact format also fits naturally into a model bench routine where small tools are used in quick succession. On a build table, the punch can be used between measuring, marking and assembly steps to create tidy openings before parts are fixed in place. It also suits general craft and maintenance work where accurate 2 mm or 3 mm holes help keep small-scale results clean and uniform.  Warning! Not suitable for children under 14 years.

Model-making tools

NON SCRATCH GRIP BAG : 74061

only available from customer service

Model-making tools

TRF Alum. Maintenance Stand 160x100x42mm

available in stores

Article number: 300042371 Product: TRF Alum. Maintenance Stand 160x100x42mm Space-efficient and safe are the watchwords for this new product, which will help re-define the way you work on your car in the pit. Tamiya logos and coloring will catch the eye, too. Item Contents/Information • Crafted in aluminum, the stand has the iconic Tamiya blue anodized finish, and comes with the TRF and twin star logos on its side. • Two holes at either end can hold your dampers, gear differentials, etc. while you work on your model. • Length: 160mm, width: 100mm, height: approximately 42mm. • Can be used with a range of models from touring cars to longer-stroke rally models, and even buggies with less rebound stroke, such as TT-02B and comical buggy models.

Model-making tools

TRF Aluminium Parts Tray 110x140mm

available in stores

Article number: 300042292 Product: TRF Aluminium Parts Tray 110x140mm Are you tired of small parts such as screws, spacers and so on rolling around your pit table and going missing? This aluminum tray eliminates such problems, keeping your table neat and tidy. Item Contents/Information • Aluminum Parts Tray x1 • Tray dimensions: 110mm x 140mm • This thin and lightweight product features deep indentations to ensure that parts do not fly out of the tray. • A handy scale is marked on the tray. Inserting your screw head in the indentation allows simple measurement of screw length. • Finished in a stylish blue and decorated with the TRF team logo.

Model-making tools

TRF RC Trolley Pit Bag with 5 Inner Boxes

available in stores

The TRF RC Trolley Pit Bag combines mobile transport and structured storage in one compact workshop companion. Its rolling format, black outer shell and blue zipper detailing give the bag a clean paddock look while keeping RC equipment contained and easier to move between home, car and track. A soft-sided outer cover encloses a drawer-style storage layout with 5 cardboard inner boxes. The large upper box is sized for a touring car model, while 4 smaller boxes create separate spaces for battery packs, parts and other RC essentials. An adjustable pull handle changes the carrying balance to suit the load, and a strap handle with a comfortable grip offers a second way to lift the bag when rolling is less practical. Tamiya logo stickers are included for added workshop styling. Exterior storage expands the layout beyond the main compartment. Pouches on the top and side keep tools within quick reach during setup and maintenance, and the rear pocket stores a setting board or other flat accessories without mixing them into the inner boxes. The water resistant material adds useful protection when transport involves damp ground or light rain, making the bag a tidy way to organize race-day gear and bench supplies.

Model-making masking tapes

40mm Masking Tape, model paint masking roll

available in stores

This 40 mm masking tape is made for model painting where broad coverage and a clean edge matter at the same time. The thin tape lays down closely across the surface, making it useful for separating colour areas on scale plastic builds and radio control bodies while keeping the masking line controlled and consistent. Its adhesive holds well even on uneven surfaces, which helps when working around shaped panels, curved sections or raised details that can challenge wider tape. The 40 mm format suits larger sections that would otherwise need several narrower strips, and the 18 m roll gives enough length for repeated workshop use. The tape can also be cut into narrower sections when a layout calls for smaller masked areas inside a wider paint scheme. Because the material does not absorb paint colour or leave marks, it supports a tidier result on both painted and unpainted model surfaces. It fits naturally into airbrush sessions, spray can work and detail painting where a sharp division between colours is needed across fuselages, bodyshells, panels or other model parts.

Model-making adhesive

Limonene Cement Extra Thin, model cement, 40 ml

available in stores

Limonene Cement Extra Thin is a model cement for plastic kit assembly, designed to run into narrow gaps between fitted parts. The extra thin consistency helps the adhesive reach seam lines cleanly, so joins can be treated after parts are positioned and held together. The bottle contains 40 ml of cement and uses a cap with an attached brush for direct application. That brush supports controlled placement along edges, corners and fine contact areas where a broader applicator would be less exact. In use, the cement can be touched to the join so it flows into the gap instead of sitting heavily on the surface. This makes it especially useful on smaller parts, close-fitting sections and assemblies where visible marks from dried adhesive would distract from the finished model. The limonene-based formula also sets this cement apart from standard hobby glues in the same work area. On the bench, it fits naturally into careful assembly routines for aircraft, cars, tanks and other plastic kits that rely on neat seams and tidy part alignment. For detail-focused building sessions, the square bottle stays easy to place beside cutters, tweezers and sanding tools while the brush cap keeps the applicator ready between steps.  Warning! Not suitable for children under 14 years.

Model-making adhesive

Limonene Cement, model adhesive, 40 ml

available in stores

Limonene Cement is a 40 ml model adhesive developed for plastic model work, combining a clear liquid formula with a citrus scent for bench sessions focused on clean joining and careful placement. The bottle format keeps the cement ready for repeated assembly steps on model parts where controlled application matters. The safety data identifies this cement for plastic model objects and names D-limonene as a key component. The liquid has a relative density of 0.86 at 20 °C, a boiling range around 175 to 176 °C, and a flash point of 48 °C. It is classified as a flammable liquid and carries warnings for skin irritation, eye irritation, allergic skin reactions, and aspiration hazard if swallowed. For that reason, handling belongs in well-ventilated work areas, with contact to skin and eyes avoided during use. On the workbench, this cement fits the steady rhythm of model assembly, whether joining smaller plastic details or preparing larger sections before the next build stage. The 40 ml content gives a practical volume for regular hobby use while keeping the bottle compact enough to store with other model-making supplies between sessions.  Warning! Not suitable for children under 14 years.